Insteon Water Leak Sensor Owner's Manual
Add to My manuals7 Pages
INSTEON Water Leak Sensor is a wireless device that detects water leaks and sends alerts to your smartphone or other connected devices. It includes a water sensor that can be placed on the floor or anywhere else where water might leak. The sensor will detect water and send a signal to the hub, which will then send an alert to your phone. You can also use the sensor to control other INSTEON devices, such as turning on lights or closing blinds. This can help you to prevent water damage and keep your home safe.
advertisement
Leak Sensor
INSTEON
®
Leak Sensor
Owner’s Manual
#
2852-222
Page 1 of 7 Rev: 10/28/2013 8:11 AM
Page 2 of 7 Rev: 10/28/2013 8:11 AM
Leak Sensor
In the Box
Leak Sensor
Quick Start Guide
Tools Needed
None
Optional Accessories
INSTEON Hub
INSTEON Setup
Some products have subtle differences in their setup procedures. Where necessary, please refer to the other device’s owner’s manual for details.
INSTEON Controllers, Responders and Links
Let’s define a few terms.
• Each INSTEON compatible product is called a device
• The INSTEON “transmitter” is called a controller
• The INSTEON “receiver” is called a responder
The association between the controller and responder is called a link
Basic INSTEON Link
Link
Controller Responder
Note that a link is one way. If you wish to have control “the other way,” simply add a link “the other way.”
Add Leak Sensor to INSTEON Hub
1) Open INSTEON App on smartphone/tablet and follow onscreen instructions to set up
Leak Sensor
Responders
Make Leak Sensor a Controller
Follow the steps below to link Leak Sensor as a controller of another INSTEON device. The linked device will respond when Leak Sensor detects moisture.
1) Press and hold Leak Sensor Set button for about 3 seconds. Leak Sensor LED will start blinking green.
2) Place Leak Sensor on floor in desired location.
3) Adjust responder to desired brightness/state
4) Press and hold responder Set button until it double-beeps. Leak Sensor LED will stop blinking.
Page 3 of 7 Rev: 10/28/2013 8:11 AM
5) Test by tapping Leak Sensor Set button. Responder will turn on.
6) To add multiple responders, repeat steps 1-5 for each additional responder
Remove Leak Sensor as a Controller (Unlink)
1) Press and hold Leak Sensor Set button until the status LED begins blinking
LED will start blinking green
2) Press and hold Leak Sensor Set button again until the status LED blink cadence changes
LED will continue blinking
3) Press and hold responder Set button until it double-beeps
Leak Sensor’s LED will stop blinking
4) Test by tapping Leak Sensor Set Button with Responder in the Off state
Former responder will not respond
Factory Reset
All settings and scenes will be erased.
1) Using a small flat blade screwdriver, carefully open the bottom case of Leak Sensor
2) Pull out the battery
3) Wait 5 seconds
4) Push in Set button and hold it. Do not let go.
5) Reinstall the battery while holding down the Set button
LED will turn on solid Green for a few seconds
LED will then turn off
6) Release Set button
Page 4 of 7 Rev: 10/28/2013 8:11 AM
Specifications
General
Brand
Manufacturer product no.
UPC
Warranty
INSTEON
INSTEON
2852-222, INSTEON Leak Sensor
813922013078
2 years, limited
INSTEON powerline mesh repeater No
INSTEON RF mesh repeater No
INSTEON controller
INSTEON responder
Yes
No
Maximum links/scenes
Commands supported as responder
400
On Group 1 (Dry)
Heartbeat (Group 4)
Software configurable
RF range
Phase bridge detect beacon
INSTEON device category
INSTEON device subcategory
Mechanical
Yes
Up to 150 feet (open air)
No
0x10
0x08 (915MHz RF frequency)
Mounting
Case color
Buttons
Plastic
Rubber
Conductive Feet
Beeper
Setup LED
Dimensions
On Group 2 (Wet)
Place on flat surface where leak will occur
White
1, Set
Polycarbonate
Polyethylene rubber
Corrosion resistant nickel plated bronze
No
Yes, green
Excluding antenna: 0.9" H x 3.6" W x 1.4 D (23mm H x 92mm W x 36mm
D)
Weight
Operating environment
Operating temperature range
Operating humidity range
Storage temperature range
Electrical
With antenna: 3.7" H x 3.6" W x 1.4" D (93mm H x 92mm W x 36mm D)
3 oz (0.2 lb, 90g)
Indoors
32-104°F (0-40°C)
0-90% relative humidity
-4-158°F (-20-70°C)
Battery
Voltage
One (1) AA battery included
1.5VDC
Retains all settings without power Yes, saved in non-volatile EEPROM
Mean battery life 10 years
Certifications FCC, IC Canada
Page 5 of 7 Rev: 10/28/2013 8:11 AM
Troubleshooting
Problem
Leak Sensor is unable to communicate with another INSTEON device
It takes a long time for one or more of
Leak Sensor’s responders to respond
Possible Cause
Leak Sensor and the other device are out of range
The other device is near a localized powerline noise source or attenuator
Leak Sensor is repeatedly retrying to control a missing responder
Solution
Install more INSTEON products
(including, but not limited to Range
Extenders/Access Points)
Isolate the noise/attenuator using a
FilterLinc
If the responder is still available, unlink it
from Leak Sensor. See Remove Leak
Sensor as an INSTEON Responder
Perform a factory reset. See Factory
None. As designed. Leak Sensor can turn responder on, but not off
Leak Sensor is not designed to turn off responders. This prevents warning lights or other leak indication devices from turning off in the event the leak dries.
If you have tried these solutions, reviewed this Owner's Manual, and still cannot resolve an issue you are having with Leak Sensor, please call the INSTEON Support Line at 1-866-243-8022
Page 6 of 7 Rev: 10/28/2013 8:11 AM
Certification and Warranty
FCC and Industry Canada Compliance Statement
This device complies with FCC Rules Part 15 and Industry Canada RSS-210 (Rev. 7). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.
The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures:
- Re-orient or relocate the receiving antenna of the device experiencing the interference
- Increase the distance between this device and the receiver
- Connect the device to an AC outlet on a circuit different from the one that supplies power to the receiver
- Consult the dealer or an experienced radio/TV technician
WARNING: Changes or modifications to this device not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Limited Warranty
Seller warrants to the original consumer purchaser of this product that, for a period of two years from the date of purchase, this product will be free from defects in material and workmanship and will perform in substantial conformity to the description of the product in this Owner’s Manual. This warranty shall not apply to defects or errors caused by misuse or neglect. If the product is found to be defective in material or workmanship, or if the product does not perform as warranted above during the warranty period, Seller will either repair it, replace it, or refund the purchase price, at its option, upon receipt of the product at the address below, postage prepaid, with proof of the date of purchase and an explanation of the defect or error.
The repair, replacement, or refund that is provided for above shall be the full extent of Seller’s liability with respect to this product. For repair or replacement during the warranty period, call the INSTEON Support Line at 866-243-8022 with the Model # and Revision # of the device to receive an
RMA# and send the product, along with all other required materials to:
INSTEON
ATTN: Receiving
16542 Millikan Ave.
Irvine, CA 92606-5027
Limitations
The above warranty is in lieu of and Seller disclaims all other warranties, whether oral or written, express or implied, including any warranty or merchantability or fitness for a particular purpose. Any implied warranty, including any warranty of merchantability or fitness for a particular purpose, which may not be disclaimed or supplanted as provided above shall be limited to the two-year of the express warranty above. No other representation or claim of any nature by any person shall be binding upon Seller or modify the terms of the above warranty and disclaimer.
Home automation devices have the risk of failure to operate, incorrect operation, or electrical or mechanical tampering. For optimal use, manually verify the device state. Any home automation device should be viewed as a convenience, but not as a sole method for controlling your home.
In no event shall Seller be liable for special, incidental, consequential, or other damages resulting from possession or use of this device, including without limitation damage to property and, to the extent permitted by law, personal injury, even if Seller knew or should have known of the possibility of such damages. Some states do not allow limitations on how long an implied warranty lasts and/or the exclusion or limitation of damages, in which case the above limitations and/or exclusions may not apply to you. You may also have other legal rights that may vary from state to state.
Protected under U.S. and foreign patents (see www.insteon.com/patents ).
© Copyright 2013 INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 866-243-8022, www.insteon.com
Page 7 of 7 Rev: 10/28/2013 8:11 AM
advertisement
Key Features
- Detects water leaks and sends alerts to your smartphone
- Easy to install and use
- Can be used to control other INSTEON devices
- Helps to prevent water damage and keep your home safe
Related manuals
Frequently Answers and Questions
Can I use the Leak Sensor outdoors?
How long does the battery in the Leak Sensor last?
Can I use the Leak Sensor to control other devices?
advertisement
Table of contents
- 3 Leak Sensor
- 3 INSTEON Setup
- 3 INSTEON Controllers, Responders and Links
- 3 Add Leak Sensor to INSTEON Hub
- 3 Make Leak Sensor a Controller
- 4 Remove Leak Sensor as a Controller (Unlink)
- 4 Factory Reset
- 3 Basic INSTEON Link
- 1 Specifications
- 6 Troubleshooting
- 7 Certification and Warranty
- 7 FCC and Industry Canada Compliance Statement
- 7 Limited Warranty
- 7 Limitations