Samsung CL29K5MQ Specifications

COLOR TELEVISION RECEIVER

Chassis : K57A(N)

Model : CL29K5MQKX/XAP

COLOR TELEVISION RECEIVER CONTENTS

1.

Precautions

2.

Specifications and IC Data

3.

Disassembly and Reassembly

4.

Alignment and Adjustment

5.

Troubleshooting

6.

Exploded View and Parts List

7.

Electrical Parts List

8.

Block Diagram

9.

Wiring Diagram

10.

Schematic Diagrams

ELECTRONICS

© Samsung Electronics Co., Ltd. MAY . 2003

Printed in Korea

AA82- 00622A

Precautions

1. Precautions

Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.

1-1 Safety Precautions

1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields.

2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers.

3. Make sure that there are no cabinet openings through which people—particularly children—might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers.

If the measured resistance is less than 1.0

megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer.

4. Leakage Current Hot Check (Figure 1-1):

Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards

Institute (ANIS C101.1, Leakage Current for

Appliances), and Underwriters Laboratories

(UL Publication UL1410, 59.7).

5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit’s AC switch first in the

ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.

DEVICE

UNDER

TEST

TEST ALL

EXPOSED METAL

SURFACES

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED

(USING AC ADAPTER

PLUG AS REQUIRED)

LEAKAGE

CURRENT

TESTER

(READING SHOULD

NOT BE ABOVE

0.5mA)

EARTH

GROUND

Fig. 1-1 AC Leakage Test

6. Antenna Cold Check:

With the unit’s AC plug disconnected from the

AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector.

7. X-ray Limits:

The picture tube is especially designed to prohibit X-ray emissions. To ensure continued

X-ray protection, replace the picture tube only with one that is the same type as the original.

Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection.

8. High Voltage Limits:

High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced.

(X-ray protection circuits also may be called

“horizontal disable” or “hold-down”.)

Heed the high voltage limits. These include the X–ray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.

1-1

Precautions

1-1 Safety Precautions (Continued)

9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components.

10. Design Alteration Warning:

Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer’s warranty.

11. Hot Chassis Warning:

Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the

AC source.

To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert.

Re-measure the voltage between the chassis and ground.

12. Some TV chassis are designed to operate with

85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source.

13. Some TV chassis have a secondary ground system in addition to the main chassis ground.

This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered.

14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards.

1-2

15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts.

16. Picture Tube Implosion Warning:

The picture tube in this receiver employs

“integral implosion” protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original.

17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some

“in-line” picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such “permanently attached” yokes from the picture tube.

18. Product Safety Notice:

Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection.

These safety features and the protection they give might be lost if the replacement component differs from the original—even if the replacement is rated for higher voltage, wattage, etc.

Components that are critical for safety are indicated in the circuit diagram by shading,

( ) or ( ).

Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications.

A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.

Samsung Electronics

Precautions

1-2 Servicing Precautions

Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions.

Warning2: An electrolytic capacitor installed with the wrong polarity might explode.

1. Servicing precautions are printed on the cabinet. Follow them.

2. Always unplug the unit’s AC power cord from the AC power source before attempting to: (a)

Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor.

3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.

4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged.

5. Check the insulation between the blades of the

AC plug and accessible conductive parts

(examples: metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug.

The insulation resistance between each blade of the AC plug and accessible conductive parts

(see above) should be greater than 1 megohm.

7. Never defeat any of the B+ voltage interlocks.

Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.

8. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last.

1-3

Precautions

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

1. Some semiconductor (“solid state”) devices are easily damaged by static electricity. Such components are called Electrostatically

Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity.

2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power— this is an electric shock precaution.)

3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge.

4. Do not use freon-propelled chemicals. These can generate electrical charges that damage

ESDs.

5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs.

6. Use only an anti-static solder removal device.

Many solder removal devices are not rated as

“anti-static”; these can accumulate sufficient electrical charge to damage ESDs.

7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.

8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.

CAUTION

These servicing instructions are for use by qualified service personnel only.

To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

1-4 Samsung Electronics

2. Specifications and IC Data

2-1 Specifications

Television System:

MODEL

TXM2792FX

SYSTEM

NTSC ONLY

Channels:

System

Band

VHF

UHF

CABLE

NTSC

2 - 13

14 - 69

1 - 125

Intermediate Frequencies (MHz) :

SYSTEM

IF Carrier Frequency

Picture IF Carrier

Sound IF Carrier

Color Sub Carrier

Picture Tube:

NTSC

45.75

41.25

42.18

29 Inch A68QCP891X100 29Inch Flat, +380MG

Power Requirements:

Antenna Input Impedance:

Speaker Impedance

AC 120V, 60Hz

VHF, UHF : Telescopic dipole antenna (75 ohm unbalanced type )

8 ohm, 15W+15W (Dual Type)

Specifications and IC Data

Samsung Electronics 2-1


2-2 IC Line Up

Loc. No

IC201S

IC301

IC501

IC602

IC801S

IC802

IC202

PC801S

PC802S

IC101

IC601

ICP01

ICW01

ICG01

Specification

SPM-464A

Table 2-1 IC Line-Up

Description

TDA9592 PS/NI, SPM-464A,64P

LA7845

TDA6108QJF

TDA7297

KA5Q1265R

KA7632

M24C08

TCET1108 / LTV817B

LA7510

MSP-3425G-B8

VIPER12AD1P

NJM2235D

4558

VERTICAL OUTPUT

RGB DRIVE AMP

SOUND-AMP (15W x 2CH)

POWER IC (STR)

CUSTOM REGULATOR (5V, 8V, 3.3V)

EEPROM

PHOTO COUPLER

IF DETECTOR-IC

Sound Processor

PWM CONTROCER-IC

VIDEO Swiching-IC

OP AMP-IC

Remark

Philips

Sanyo

Philips

Philips

FIAIR CHILD

FIAIR CHILD

TEMIC

Micronas


2-3 Semiconductor Base Diagrams

ELECTROLYTIC-

CONDENSER

DIODE


IC

SPM464A(Pin 64)

MSP3425G(Pin 52)

LM393(Pin 8)

VIPER12ADIP(Pin 8)

M24C08(Pin 8)

4558(Pin 8)

NJM2235D(Pin 8)

TRANSISTOR

KSD5703

KSA614

B

C

E

IC

LA7845(Pin 7)

TDA6108Q(Pin 9)

KA7632(Pin 10)

TRANSISTOR

KSC815-Y

KSA539-Y

E B C

11

1

SAW-FILTER

TRANSISTOR

KSC2331-Y

M3953M

M9370M

Fig. 2-1 Semiconductor Base Diagrams

E C B


2-4

MEMO

3. Disassembly and Reassembly

3-1 Back Cover Removal

Disassembly and reassembly

1. After removing the screws, press the tension rib and pull the cabinet backwards.

2. To reassemble, press the tension rib (see diagram).



3-2 Main Board Removal

1. Separate the socket board from the CRT neck.

2. Remove the Anode Cap from the CRT.

3. Remove the main board by pulling it with both hands.

Warning: The FBT is charged with high voltage.

Before removing the Anode Cap, discharge the voltage through one of the heat sinks on the main board.

3-3 Speaker Removal

1. Remove the speaker by pressing the tension rib.


3-4 CRT Removal


Samsung Electronics

1. Spread a soft mat on the floor. Place the TV set face down.

2. Remove the 4 nuts mounting the CRT to the front cabinet. Lift the CRT.

3. Caution: Because of the high vacuum and large surface area of the picture tube, be careful while handling it: (1)

Always lift the picture tube by grasping it firmly around the faceplate, (2) Never lift the tube by its neck. (3) Do not scratch the picture tube or apply excessive pressure.

Fractures of the glass may cause an implosion.

3-3

MEMO


Alignment and Adjustments

4. Alignment and Adjustments

4-1 Preadjustment

4-1-1 Factory Mode

1. Do not attempt these adjustments in the Video

Mode.

2. The Factory Mode adjustments are necessary when either the EEPROM (IC202) or the CRT is replaced.

3. Do not tamper with the “Adjustment” screen of the Factory Mode menu. This screen is intended only for factory use.

4-1-2 When EEPROM (IC202) Is Replaced

1. When IC202 is replaced all adjustment data revert to initial values. It is necessary to re-program this data.

2. After IC202 is replaced, warm up the TV for

10 seconds.

4-2 Factory/Service Mode

4-2-1 Procedure for the “Adjustment” Mode

1. This mode uses the standard remote control.

The Service Mode is activated by entering the following remote-control sequence :

(1) DISPLAY

→ FACTORY.

(2) STAND-BY → MUTE → 1 → 8 → 2

→POWER ON.

2. The “SERVICE (FACTORY)” message will be displayed. The Service Mode has four components: ADJUST, OPTION , G2-ADJUST and

RESET.

3. Access the Adjustment Mode by pressing the

“VOLUME” keys ( Up or Down). The adjustment parameters are listed in the accompanying table, and selected by pressing the CHAN-

NEL keys ( , ).

4-1-3 When CRT Is Replaced

1. Make the following adjustments AFTER setting up after setting up purity and convergence :

White Balance

Sub-Brightness

Vertical Center

Vertical Size

Horizontal Size

Fail Safe (This adjustment must be the last step).

2. If the EEPROM or CRT is replaced and set SC as 30(factory mode).

4. Selection sequences for the all system:

DOWN or UP key:

SCT>SBT>BLR>BLB>RG>GG>BG>VSL>VS>

VA>HS>SC>CDL>STT>AKB>NDL>NSR>

SCBT>VOL>CAP>MVOL>RP00>RP01>

AGCS>OMD>SCL>PWL>MUS>AGC>

HPAR>HBOW>EWID>EPAR>EUCN>ELCN>

ETRP>VZ>SVM>VMA>SSP>PSNS>

DNSR>DSBT>DCDL>DBLR>DBLB>DSK

5. The VOLUME keys increase or decrease the adjustment values (stored in the non-volatile memory) when Adjustment Mode is cancelled.

6. Cancel the Adjustment Mode by re-pressing the “FACTORY” or “Power OFF” keys.



4-2-2 Main Adjustment Parameter

15

16

17

18

19

10

11

12

13

14

5

6

7

8

9

NO

1

2

3

4

28

29

30

31

32

23

24

25

20

21

22

26

27

O SD F U N CT I ON

SCT Su b Co n t ra s t

SBT Su b Br i g h t n e s s

BLR

BLB

Bl a c k Le v e l o f f se t R

Bl a c k Le v e l o f f se t B

RG

GG

R e d G a i n

G r e e n G a i n

BG Bl u e G a i n

VSL Ve r t i ca l S lo p e

VS Ve r t i ca l Sh i f t

VA

HS

Ve r t i ca l A m p l i t u d e

H o r i z o n t a l Sh i f t

SC S- Co r r e c t i o n

CD L Ca t h o d e D r i ve Le ve l

ST T Su b T i n t

RP00

RP01

AGCS

OMD

SCL

PWL

MUS

AGC

AKB A K B O n / o f f

ND L NT SC De l a y

NSR N T SC Su b c o l o r

SCBT S c r e e n B r i g h r t n e s s

VO L Vo l u m e p re s e t t i n g

CAP C a p t i o n P o s i t i o n

MVOL M e l o d y V o l u m e

R a t i o P r e / o v e r s h o o t

R a t i o P r e / o v e r s h o o t

HPAR

HBOW

EWID

I F A G C S p e e d

O f f s e t I F D e m o d u l a t o r

S o f t C l i p p i n g L e v e l

P e a k W h i t e L i m i t t i n g

C o l o r M a t r i x

A u t o m a t i c G a i n C o n t r o l

H o r i z o n t a l P a r a l l e l o g r a m

H o r i z o n t a l B o w

E W W i d t h

R A N G E

0 ~ 23

0 ~ 23

0 ~ 6 3

0 ~ 6 3

0 ~ 1

0 ~ 1 5

0 ~ 2 3

0 ~ 6 3

0 ~ 6 3

0 ~ 1 5

0 ~ 5 0

0 ~ 6 3

0 ~ 6 3

0 ~ 6 3

0 ~ 6 3

0 ~ 6 3

0 ~ 6 3

0 ~ 6 3

0 ~ 6 3

0 ~ 1 5

0 ~ 7

0 ~ 1

0 ~ 1

0 ~ 3

0 ~ 6 3

0 ~ 3

0 ~ 1 5

0 ~ 1

0 ~ 6 3

0 ~ 6 3

0 ~ 6 3

0 ~ 6 3

10

12

7

1

1

5

0

1

5

36

I N I T I A L D AT A

13

9

32

32

28

31

32

30

25

31

27

29

11

15

1

33

1

15

3

32

32

32

SELECTION

FIX

FIX

FIX

FIX

FIX

ADJ

ADJ

FIX

FIX

FIX

ADJ

FIX

ADJ

ADJ

FIX

RE M ARK

ADJ

ADJ

ADJ

ADJ

FIX

FIX

ADJ

ADJ

ADJ

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX



37

38

39

40

41

NO

33

34

35

36

45

46

47

42

43

44

O SD

EPAR

EUCN

ELCN

ETRP

VZ

SVM

VMA

SSP

PSNS

DNSR

DSBT

DCDL

DBLR

DBLB

DSK

F U N CT I ON

E W P a r a b o l a

E W U p p e r C o n e r

E W L o w e r C o n e r

E W T r a p e z i u m

V e r t i c a l Z o o m

D e l a y o f R G B t o V M O u t p u t

A m p l i t u d e o f S V M O u t p u t

S u b S h a r p n e s s

I d e n t i f i c a t i o n s e n s

N S R i n D V D m o d e

S B T i n D V D m o d e

C D L i n D V D m o d e

B L R i n D V D m o d e

B L B i n D V D m o d e

D y n a m i c S k i n T o n e C o n t r o l

R A N G E

0 ~ 6 3

0 ~ 6 3

0 ~ 6 3

0 ~ 6 3

0 ~ 6 3

0 ~ 3

0 ~ 3

0 ~ 2 0

0 ~ 1

0 ~ 2 3

0 ~ 2 3

0 ~ 1 6

0 ~ 6 3

0 ~ 6 3

0 ~ 1

10

32

32

0

1

5

4

I N I T I A L D AT A

32

12

12

12

48

0

3

5

SELECTION

FIX

FIX

FIX

FIX

FIX

RE M ARK

ADJ

ADJ

ADJ

ADJ

FIX

FIX

FIX

FIX

FIX

FIX



4-2-3 Option Bytes

In the Service Mode, various can be selected via the Option Table. Example:

13

14

5

6

7

8

9

10

11

12

3

4

1

2

OSD

SYSTEM

VIDEO MUTE

ZOOM

AUTO POWER

AUDIO MUTE

START LANG.

HOTEL MODE

BULE SCREEN

V-CHIP

AV OPTION

TILT

DEMO

EXT COMB

V-Guard

Option Table : xx xx

SETTING

CT-N EN/SP/FR

OFF

NOR/ZOOM

OFF

ON

ENGLISH

OFF

OFF

ON

AV1/AV2/S-V/DVD

ON

OFF

OFF

ON

REMARK

- Language

- Video Mute On/Off changing the channel

- Picture Size Option

- Master S/w Option

- Audio Mute On/ Off without signal

- Inital Language agter Factory Reset

- Hotel mode On/ Off

- Bule Screen On/ Off without signal

- V-CHIP ON/OFF (U.S.A)

- AV + S-V + DVD

- TILT ON/OFF

- DEMO ON/OFF

- External 2H-COM ON/OFF

- Vertical Guard ON/OFF (*MAIN PCB A LOT : OFF)



4-2-4 RESET

The Reset Mode is used during factory inspection.

Function Reset:

1. Picture Mode

4.

Melody

5.

Surround

6.

Turbo Sound

7. MTS

8. Language

9.

Caption

10. Timer

Dynamic

Custom

Off

On

Off

Off

Stereo

English

Off

Off

4-3 Other Adjustments

4-3-1 General

1. Usually, a color TV needs only slight touchup adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus.

2. The picture should have good black and white details. There should be no objectionable color shading; if color shading is present, perform the purity and convergence adjustments described below.

3. Use the specified test equipment or its equivalent.

4. Correct impedance matching is essential.

5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the

TV. When inserting signal markers, do not allow the marker generator to distort test results.

6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate.

7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.

8. To protect against shock hazard, use an isolation transformer.

4-3-2 Automatic Degaussing

A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation.

The degaussing coil operates for about 1 second after the power is switched ON. If the set has been moved or turned in a different direction, disconnect its AC power for at least 30 minutes.

If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil.

Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before removing power.



4-3-3 High Voltage Check

CAUTION: There is no high voltage adjustment on this chassis.

The B+ power supply must be set to +130 volts (Full color bar input and normal picture level).

1. Connect a digital voltmeter to the second anode of the picture tube.

2. Turn on the TV. Set the Brightness and

Contrast controls to minimum (zero beam current).

3. The high voltage should not exceed 33KV.

4. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 33KV under any conditions.

4-3-4 FOCUS Adjustment

1. Input a black and white signal.

2. Adjust the tuning control for the clearest picture.

3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen.

4-3-5 Cathode Voltage Adjustment

(Screen Adjustment)

1. Input a Toshiba pattern.

2. Go to service mode and select ‘G2-Adjust.

3. Adjust bottom VR of FBT to display

“SCREEN ADJUST : OK”

4. Use the Menu or Mute key to complete

G2 adjustment.

4-3-6 Purity Adjustment

1. Warm up the receiver for at least 20 minutes.

2. Plug in the CRT deflection yoke and tighten the clamp screw.

3. Plug the convergence yoke into the CRT and set in as shown in Fig. 4-2.

4. Input a black and white signal.

5. Fully demagnetize the receiver by applying an external degaussing coil.

6. Turn the CONTRAST and BRIGHTNESS controls to maximum.

7. Loosen the clamp screw holding the yoke.

Slide the yoke backward or forward to provide vertical green belt. (Fig. 4-3).

8. Tighten the convergence yoke.

9. Slowly move the deflection yoke forward, and adjust for the best overall green screen.

10. Temporarily tighten the deflection yoke.

11. Produce blue and red rasters by adjusting the low-light controls. Check for good purity in each field.

12. Tighten the deflection yoke.


6 Pole Magnet

Clamper

Screw

4 Pole Magnet

2 Pole Magnet

2 POLE

PURITY

YOKE

CLAMP

SCREW

6 POLE

CONVERGENCE

4 POLE

CONVERGENCE

Fig. 4-2 Convergence Magnet Assembly

Vertical Green Belt


ADJUST THE ANGLE

(VERTICAL LINES)

31m/m

Samsung Electronics

1

2

Fig. 4-4

Fig. 4-3 Center Convergence Adjustment

4-3-7 White Balance Adjustment

(a) Set up

1. Warm up the TV for at least 30 minutes in the

Aging Mode (OSD White). This mode is displayed by entering the following sequence:

DISPLAY

→

FACTORY

→

FACTORY

2. Input a Toshiba pattern.

(b) Low-Light Adjustment

1. Set SBT to 1.5 fL in the Factory Service

Mode with using CA100. See Fig. 4-4.

2. Adjust RG,BG so that the levels are suitable to each local area.

(c) High-Light Adjustment

1. Set SCT to 45 FL in the Factory Service Mode with using CA100.

See Fig. 4-4 .

4-7


4-3-8 Center Convergence Adjustment

1. Warm up the receiver for at least 20 minutes.

2. Adjust the two tabs of the 4 pole magnets to change the angle between them. Superimpose the red and blue vertical lines in the center area of the screen.

3. Adjust the Brightness and Contrast controls for a well defined picture.

4. Adjust the two-tab pairs of the 4 pole magnets, and change the angle between them.

Superimpose the red and the blue vertical lines in the center area of the screen.

BLUE

RED

BLUE RED

5. Turn the both tabs at the same time, keeping the angle constant, and superimpose the red and blue horizontal line in the center of the screen.

6. Adjust the two-tab pairs of the 6-pole magnets to superimpose the red and blue line onto the green. (Changing the angle affects the vertical lines, and rotating both magnets affects the horizontal lines.)

7. Repeat adjustments 2~6, if necessary.

8. Since the 4-pole magnets and 6-pole magnets interact, the dot movement is complex

(Fig. 4-5).

RED/BLUE GREEN

RED/BLUE

GREEN

4-Pole Magnet Movement 6-Pole Magnet Movement

Fig. 4-5 Center Convergence Adjustment



4-3-9 RF AGC Adjustment

Set the AGC data to 33 (Factory Mode).

4-3-10 Sub-Color Adjustment

4-3-11 Geometry Adjustment

SC →VS→VA→VSL→HS

1. Input a lion head pattern.

2. Set the SC (S-Correction) as 29 and VS(Vertical

Shift) 31 so that the lion head circle becomes oval.

3. Adjust with VA (Vertical Amplitude) so that the top margin of the picture is 4.

5 5

Fig. 4-9

6. Adjust EWID (EW Width) so that the left and right margins of the picture are 5.

7. Input a cross-hatch pattern.

4

Fig. 4-7

4. Adjust with VSL (Vertical-Slope) so that the bottom margin of the picture is 4.

4

Fig. 4-8

5. Adjust with HS (Horizontal Shift) so that the lion-head pattern and CRT centers are aligned.



8. Adjust EW Geometry

1 HPAR (Horizontal Parallelogram)

2 HBOW (Horizontal Bow)

3 EWID (EW Width)

4 EPAR (EW Parabola)

5 EUCN (EW Upper Coner)

6 ELCN (EW Lower Coner)

7 ETRP ( EW Trapezivm)




MEMO


Troubleshooting

5. Troubleshooting

5-1 No Power

Counect the Power code

Check the

Power LED

LED Off

Check the

12.5V-A Line

LED On

Normal

Abnormal

Check the

3.3V-A,8V-A Line of IC201S

Abnormal

Check the

FD802S, IC801S or AC-Fuse

Check/Replace

IC802

Normal Check the

X-tal,SDA,SCL port of IC201S

Abnormal

Normal Replace

IC201 S

Check the

(33)Pin (H-Drive) of IC201S Abnormal

Normal

Check the

130V- A Line

Abnormal

Normal

Check / Replace

Q401

Check the

FBT,D808


Troubleshooting

5-2 No Video (Sound OK)

Check RK,GK,BK

Signal

Abnormal

Nornal

Check the

Voltage of heater

Abnormal

Nornal

Check/Replace

R418,R522,R523

Check R,G,B

Signal into CRT

PCB

Nornal

Abnormal

Check IC501

B+(180V-B)

Nornal

Abnormal

Check the resistance of R519

Check IC301

-

+

B Volt

Abnormal

Nornal

Abnormal

IC301 Check/Replace

D406,R414,D405,R413

Check/Replace

Nornal

Replace

R519

Check

CRT and FBT

Abnormal

Check/Replace

IC201S

Abnormal

Check IC201S

Pin 51,52,53

(R.G.B)

Nornal

Check IC201S

Pin50(IK,V-GUARD)

Nornal

Check

CRT and FBT

Check/Replace

D407,FBT


Troubleshooting

5-3 No Sound (Video OK)

Abnormal

Check

IC101,TUNER

Abnormal

Check

B+ Line

5V-B, 8V-B

Checkthe signal

Output from CN602

CN603

Abnormal

Normal

Check

Speaker and Wire

Check IC602

Pin4,12

Abnormal

Normal

Check IC602

B+

Abnormal

Check IC601

Pin47(SIF)

Normal

Check IC601

B+

Normal

Check/Replace

IC601

Check FD801S

D805

Normal

See

No Power

Normal

Replace

IC602

Abnormal

Replace

FD801S,D805


Troubleshooting

5-4 Horizontal Lines Appear or Screen

Check IC301 B+

16V-C,-13.5V-C

Normal

Check IC201S

Pin 21,22

(VDN,VDP)

Normal

Check / Replace

IC301

Abnormal

Abnormal

Check

R413,R414

D405,D406

Check

IC201S


6. Exploded View & Parts List

6-1 CL29K5MQKX/XAP

You can search for the updated part code through ITSELF web site.

URL : http://itself.sec.samsung.co.kr

Samsung Electronics

Exploded View & Parts List

2

2-1

2-2

2-3

No Code No Description;Specification

1-12

1-13

1-14

1-15

1-7

1-8

1-10

1-11

1-3

1-4

1-5

1-6

1

1-1

1-2

AA64-03418B

AA64-70117B

AA64-02629A

AA61-60003J

AA96-00906S

AA96-01156A

6003-001268

AA65-00011B

AA61-40113A

AA64-02632A

6003-001026

AA64-02635A

6003-001026

AA91-00507A

6006-001095

CABINET FRONT;29K5,HIPS,HB,G4309,SV012 K

BADGE-BRAND;-,AL,-,-,L65,R2000,SILVER,SS

KNOB-POWER;29K5,ABS HB,G3676,SVM-3012

SPRING ETC-CS;-,SUS304,-,-,OD6,N7,OD6,-,

ASSY COVER P-FRONT;29K5,XAX,HIPS HB,G430

ASSY MISC,A/V SIDE,CFT2791KX/SMS;K57A

SCREW-TAPTITE;TH,+,B,M4.0,L12.0,ZPC(YEL)

CLAMP-WIRE;ALL MODEL,NYLON 66,V2,NTR,15M

STOPPER-PCB;-,ABS,HB,NTR.

WINDOW-RMC,LED;29K5,PC,CLR

SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR

KNOB-CONTROL;29K5,ABS HB,G3676,SVM-3012


ASSY HOLDER SPK;-,-,8OHM/15W,-,ASSY HOLD

SCREW-ASS’Y TAPT;WP,BH,+,M4,L12,ZPC(YEL)

Q’ty Remark

1

4

1

1

1

1

1

1

1

2

1

1

1

1

1

CWFCL

SP

WR

WR+CF

KC

KC+CF

AHS

SPK+CF

CF

BADGE

KP

SPRING

F/C

APAVS

AV+CF

AA03-00273A

AA60-10050V

AA65-00019A

3704-000114

CRT COLOR;A68QCP891X100 ,380MG,1.11MH,14

SCREW-ASSY;WC,HH,+,M6,L30,SWRCH18A,ZPC(S

CLAMP CORE-D,COIL;25-34,NYLON 66,V2,NTR

SOCKET CRT;14P,29.1,35.5SN,1SH09S/BK

1

4

4

1

CRT

CRT+CF

C/CORE

VA999

3

3-1

3-2

AA64-03417B

6003-001026

AA96-20109C

CABINET BACK;29K5,HIPS,HB,G4309


ASSY PWR-CORD;CP2/NO(4.0)H/C300,KKP419C,

1

7

1

C/B

CB+CF

PWR/AC

6-1

Electrical Parts List

7. Electrical Parts List

7-1 CL29K5MQKX/XAP

Loc. No.

Code No.

Description ; Specification

ASSY CHASSIS

1 A/CHASSIS AA91-06211W ASSY CHASSIS;CL29K5MQKX/STR,K57A

3 CN603

3 CN502

3 CN701

3 CN501

3 Q801

4

4

3 Q402

3 Q401

4

4

4

3 IC802

4

4

4

4

4

3 IC801S

4

4

4

3 IC602

4

3

3

2 A/MAIN AA94-13064A ASSY PCB MAIN;29K5,K57A,LATIN

3 0202-000008 SOLDER-WIRE;S63S-D3.0,S63A,D3,63/37

3

0202-000187 SOLDER-WIREFLUX;-,RS60S,D1.2,6

0204-000442 SOLVENT;CH3-CH5H-CH396%IM-1000

0204-001024 FLUX;DF-96TVS,-,20%,-

4

4

3 D801S

4

4

AA96-00276C ASSY H/S;-,BRIDGE ,AA62-00052A,GSIB660,

0205-000129 GREASE-SILICON;SC102,JAPAN

0402-001399 DIODE-BRIDGE;GSIB660,600V,6A,SIP-4,BK

6003-000335 SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR

AA60-30003A WASHER;-,-,-,-,T1.5,-,SBHG-1

4

3 D404

AA62-00052A HEAT SINK-PS;-,-,-,SILVER,HOLE 18.5mm, 2

0402-001296 DIODE-RECTIFIER;FMP-3FU,1500V,5A,T0-3PF

3 PC801S 0604-001038 PHOTOCOUPLER;TR,130-260%,200MW

3 ICW01 1001-000211 IC-VIDEO SWITCH;NJM2235D,-,DIP,8P,300MIL

3 IC202 1103-001200 IC-EEPROM;M24C08-WBN6,1024x8Bit,DIP,8P,3

3 IC601 1204-001662 IC-SOUND PROCESSOR;MSP3425G-B7,DIP,52P,5

3 NT801S 1404-001045 THERMISTOR NTC;4.7OHM,15%,2900K,35.0MW,T

3 PT801S 1404-001264 THERMISTOR-PTC;4.5OHM,+30/-20%,220V,290V

3 CY801S 2201-000446 C-CERAMIC,AC;CK45PE400V332-M(T

3 CR403S 2306-000327 C-FILM;CF922P1.6KVT632-H-25/85

3 CX801S 2306-000318 C-FILM,MPPF;220NF,20%,250V,-,2

3 CR406S 2306-001017 C-FILM,MPPF;680NF,5%,400V,26X1

3 C803

3 C821

3 SF101S

2401-003031 C-AL;470uF,20%,450V,GP,BK,35x45mm,1

2401-003633 C-AL;220UF,20%,160V,GP,ST,22X25MM,1

2904-001107 FILTER-SAW AV;45.75MHz,SIP5K,TP,12.6dB,N

3 SF102S

3 RL801S

3 FP801S

3 JA701

3 JA702

2904-001418 FILTER-SAW AV;45.75MHZ,-,ST,-,-,-

3501-001040 RELAYPOWER;12VDC,500MW,10A,1FO

3601-000293 FUSE-CARTRIDGE;250V,5A,SLOW-BLOW,GLASS,5

3722-001333 JACK-RCA9P,3.2mm,NI,BLK

3722-001423 JACK-RCA;3P+S1P,3.4mm,NI,BLK,-

3 IC201S

3 T444S

3 T801S

3 T401A

3 L808

3 L409

3 L410

3 LX801S

3 WG

3 TU01S

AA09-00316A IC MICOM;TDA9592PS/N1/3I,SPM-464A,64P,3.

AA26-00057A TRANS-FBT;-,FUH-29A001B(S),25/29,130

AA26-00179C TRANS SWITCHING;EER4950,K57A,CFT2791KX,9

AA26-50001M TRANS HORIZ DRIVE;-,80MH,520UH,4UH,E

AA27-00098A COIL CHOKE;-,-,24uH,10%,-,0.1,3.0A,DR10X

AA27-00056A COIL HORIZ. WIDTH;-,600uH,YL9N 15x27.5 C

AA27-00067A COIL HORIZ. WIDTH;-,240uH,YL9N 12x20 C:6

AA29-00011A FILTER LINE NOISE;CZ32W8,-,0.20MAX,1.5KV

AA39-20010B LEAD-CONNECTOR,ASSY;-,YFH800-01,500MM,1P

AA40-00073A TUNER-TECC1040PG32A(S),181CH,45.75MHZ,75

3711-002644 POST-HEADER;67094-005(AUTO)

3711-002645 POST-HEADER;67094-006(AUTO)

3711-002647 POST-HEADER;67094-008(AUTO)

3711-002648 POST-HEADER;67094-009(AUTO)

0502-000242 TR-POWER;KSA614,PNP,-80V,-55V,

0502-001007 TR-POWER;KSC2073-H2,NPN,150V,1

AA96-00624A ASSY H/S;-,POWER,AA62-00057A,KSD5703,WA


0502-001136 TR-POWER;KSD5703,NPN,70W,TO-3PF,ST,8-

6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW

AA60-30001A WASHER-PLATE;-,M3,ID3.5,15X8.5,T1.0,-,SB

AA62-00057A HEAT SINK-PS;-,-,T1.0,-,41*20*60,D2,-,-,

AA96-00245A ASSY H/S;-,-,AA62-00055A,KA7632,-

1203-001939 IC-POSI.FIXED REG.;7632,SIP,10P,-,PLASTI

6003-000334 SCREW-TAPTITE;RH,+,2S,M3,L6,ZP

AA62-00055A HEAT SINK-PS;-,-,T1.0,-,35*15*25,D1,-,-,

AA96-50371J ASSY H/S;BRKT+SCREW,KA5Q1265RF,OIL SILIC


1203-002597 IC-PWM CONTROLLER;KA5Q1265RF-YDTU,TO-3PF


AA61-11028A BRACKET-IC;SECC,T1.0,-,

AA62-30181H HEATSINK-ES;-,AL6063EXTR.,2,WHT,50MM,-

AA96-50398A ASSY-H/S;-,-,AA62-30182E,TDA7297,-


Remark Loc. No.

Code No.

Description ; Specification Remark

4 D408

4 D304

4 D802

4 D803

4 D402

4 D403

4 D951

4 D807

4 D405

4 D401

4 D406

4 DE04

4 D303

4 D407

4 D409

4 DE02

4 DZ101

4 DZ204

4 DZ213

4 DZ214

4 DZ215

4 DZ402

4 DZ601

4 DZ602

4 DZ805

4 DZ806

4 DZ809

4 DZ201

4 DZ812

4

4

4

3 IC301

4

4

4

4

3 D805

1201-001064 IC-POWERAMP;7297,ZIP,15P,-,DUA


AA62-30182E HEAT-SINK,ES;-,A6063 EXTR,-,WHT,-,-,-,40

AA96-50406G ASSY H/S;,POWER,AA62-30180K,K57A

1204-001807 IC-VERTICAL PROCESSO;LA7841,SIP,7P,708MI


AA62-30180K HEATSINK-ES;-,A6063EXTR,-,WHT,50/13,-,


BP96-00020F ASSY HEAT SINK P;H/S TR,SCREW,FFPF10U20S

4

4

4

4

3 D808


0402-001375 DIODE-RECTIFIER;FFPF10U20S,200V,10A,TO-2


AA62-00045A HEAT SINK-PS;-,-,T1.0,-,-,DREAM,-,-,-,-,

BP96-00020J ASSY HEAT SINK P;H/S TR,SCREW,FMG-G2CS,O

4

4

4

4


0402-001230 DIODE-RECTIFIERFMG-G2CS,1000V,3A,TO-22



3 PWR/AC AA96-20109C ASSY PWR-CORD;CP2/NO(4.0)H/C300,KKP419C,

4

4

AA39-10006X POWER-CORD;-,KKP419C,KLCE-2F,2.286MT

AA61-20284A HOLDER P CORD;PP,VO,BLK,KE-002

3 L/PQS AA68-01018A LABEL-PQS,-,50mmX,13,-,WHITE,-

3 CR402S 2301-001037 C-FILM,PPF;6.8NF,3%,1600V,TP,2

3 LR401S AA27-00099A COIL LINEARITY;23.5uH,23.5uH,DR14x15C:5.

3 QE01

3 L405

3 ICE01

3 SW201

3 RM201

0505-001723 FET-SILICON;FQP630TSTU,N,200V,9A,0.4OHM,

AA27-00057A COIL HORIZ. WIDTH;-,10mH,YL-9N 15x27.5 C

1202-000103 IC-VOLTAGECOMP.393,DIP,8P,300MIL,DUAL,

3404-001004 SWITCH TACT;12V,50MA,160GF8.4X22.7MM

AA32-00015A MODULE-REMOCON;FRP-3521H31,38KHZ,940MM,M

3 C406

3 LD201

2301-001296 C-FILM,MPPF;720NF,5%,400V,BK,26X15.5X20M

AA96-00555A ASSY LED GUIDE;-,-,UEX-LD-030,GREEN

3 A/AUTO AA97-13903Q ASSY AUTO-MAIN;CL29K5MQKX/XAX,K57A

4 D202 0401-000005 DIODE;1N4148,100V,300mA,1V,8nS,TAPING

4 D206 0401-000005 DIODE;1N4148,100V,300mA,1V,8nS,TAPING

4 D804

4 D809

4 D811

4 DZ403

4 DE01

0401-000005 DIODE;1N4148,100V,300mA,1V,8nS,TAPING







0401-000006 DIODE-SWITCHING;BAV21,250MA,400MW,50NS,2

0401-000006 DIODE-SWITCHING;BAV21,250MA,400MW,50NS,2

0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41



0402-000493 DIODE-RECTIFIER;1R5GU41,400V,1

0402-000534 DIODE-RECTIFIER;RG10V,400V,1.5

0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5



0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.




0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500















Loc. No.

Code No.


4 DZ223

4 DZ224

4 DZ808

4 DZ208

4 DZ216

4 DZ217

4 DZ219

4 DZ801

4 DZ303

4 DZ804

4 DZ301

4 DZ305

4 DZ302

4 DZ810

4 D602

4 D201

4 Q205

4 Q206

4 Q211

4 Q702

4 DZ802

4 DZ306

4 DZ811

4 DZ803

4 DZ202

4 DZ205

4 DZ206

4 DZ207

4 DZ209

4 DZ210

4 DZ211

4 DZ212

4 DZ218

4 DZ220

4 DZ221

4 DZ222

0403-000699 DIODE-ZENER;TZP27B,27V,27-30.8

0403-000700 DIODE-ZENER;TZP33A,33V,31-35V,

0403-000700 DIODE-ZENER;TZP33A,33V,31-35V,

0403-000716 DIODE-ZENER;MTZJ4.7B,4.7V,4.55-4.8V,500m




















0403-001211 DIODE-ZENER;MTZJ12B,11.44-12.03V,500MW,D

0403-001221 DIODE-ZENER;UZ39BSB,35.36-37.19V,500MW,D

0403-001327 DIODE-ZENER;MTZJ18A,16.22-17.06V,500mW,D



0403-001329 DIODE-ZENER;MTZJ24B,22.61-23.77V,500mW,

0403-001373 DIODE-ZENER;MTZJ5.1A,4.81V-5.07V,500mW,D

0404-000156 DIODE-SCHOTTKY;RB441Q,10V,100MA,DO-34,TP

0404-000156 DIODE-SCHOTTKY;RB441Q,10V,100MA,DO-34,TP

0501-000283 TRANSISTOR;KSA539-Y(TAPG)/YTAM




4 R211

4 R212

4 R214

4 R215

4 R219

4 R220

4 R272

4 R273

4 R274

4 R275

4 R276

4 R417

4 R420

4 R809

4 R316

4 J708

4 R712

4 R713

4 R103

4 R202

4 R210

4 Q301

4 Q951

4 Q203

4 Q204

4 Q207

4 Q208

4 Q802

4 Q701

4 IC603

4 IC803


0501-000369 TRANSISTOR;KSC2331-Y(TAPG)

0501-000389 TRANSISTOR;KSC815-Y(TAPG)/YTAM






1203-000515 IC-VOL. DETECTOR;7042,TO-92,3P,177MIL,PL

1203-001217 IC-POST,ADJUSTREG;431,T0-92,3P,4.58MIL,P

4 VX801S 1405-000187 VARISTOR;750V,1250A,12.5x7mm,TP

4 R231 2001-000005 R-CARBON;390OHM,5%,1/8W,AA,TP,

4 R903

4 R906

4 R289

2001-000005 R-CARBON;390OHM,5%,1/8W,AA,TP,


2001-000011 R-CARBON;75Kohm,5%,1/8W,AA,TP,1.8x3.2mm

4 R216

4 R306

4 R806

4 R405

4 R817

2001-000012 R-CARBON;680Kohm,5%,1/8W,AA,TP,1.8x3.2m

2001-000016 R-CARBON(S);1OHM,5%,1/2W,AA,TP

2001-000019 R-CARBON(S);10ohm,5%,1/2W,AA,TP,2.4x6.4m

2001-000020 R-CARBON(S);22OHM,5%,1/2W,AA,T

2001-000020 R-CARBON(S);22OHM,5%,1/2W,AA,T

2001-000085 R-CARBON(S);100KOHM,5%,1/2W,AA


2001-000109 R-CARBON(S);470OHM,5%,1/2W,AA,

2001-000258 R-CARBON;1.8Kohm,5%,1/8W,AA,TP,1.8x3.2m

2001-000258 R-CARBON;1.8Kohm,5%,1/8W,AA,TP,1.8x3.2m

2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP

2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP















Remark Loc. No.

Code No.


4 R294

4 R829

4 RE08

4 R204

4 R205

4 R221

4 R222

4 R601

4 R602

4 R603

4 R604

4 RE04

4 R270

4 R271

4 R203

4 R208

4 R209

4 R223

4 R230

4 R236

4 R293

4 R716

4 R101

4 R102

4 R250

4 R719

4 R228

4 R229

4 R814

4 R245

4 R401

4 R261

4 R314

4 R833

4 R907

4 R908

4 R901

4 R904

4 R251

4 R718

4 R279

4 R609

4 R611

4 R248

4 J213

4 R207

4 R617

4 RE01

4 R256

4 R717

4 R260

4 R213

4 R258

4 R615

4 R618

4 R619

4 R813

4 R822

4 R835

4 RE03

4 R315

4 R277

4 R288

4 R296

4 R605

4 R606

4 R607

4 R608

4 R613

4 R614

4 RW01

4 RW02

4 RW04

4 RW05

4 RE07

4 RW03

4 R206
















2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,













2001-000343 R-CARBON;130OHM,5%,1/8W,AA,TP,1.8X3.2MM







2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP
















2001-000563 R-CARBON;27KOHM,5%,1/8W,AA,TP,1.8X3.2MM




















2001-000739 R-CARBON;4.7MOHM,5%,1/8W,AA,TP

2001-000739 R-CARBON;4.7MOHM,5%,1/8W,AA,TP

2001-000780 R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm






Loc. No.

Code No. Description ; Specification Remark Loc. No.

4 R104

4 R714

4 R246

4 R201

4 R217

4 R610

4 R612

4 R136

4 R257

4 R105

4 R708

4 R711

4 R247

4 R705

4 R706

4 R707



2001-000793 R-CARBON;47OHM,5%,1/8W,AA,TP,1














4 R709

4 R710

4 R292

4 R812

4 R402

4 R823

4 R824

4 R828

4 R404

4 R825



2001-000989 R-CARBON ;820Kohm,5%,1/8W,AA,TP,1.8x3.2m

2001-001067 R-CARBON(S);11KOHM,5%,1/2W,AA,TP,2.4X6.4

2001-001077 R-CARBON(S);150OHM,5%,1/2W,AA,




2001-001114 R-CARBON(S);270OHM,5%,1/2W,AA,

2001-001131 R-CARBON(S);33KOHM,5%,1/2W,AA,

4 R803

4 R804

4 R827

4 R807

4 R808



2001-001168 R-CARBON(S);6.8KOHM,5%,1/2W,AB

2001-001170 R-CARBON(S);6.8OHM,5%,1/2W,AB,

2001-001170 R-CARBON(S);6.8OHM,5%,1/2W,AB,

4 R810

4 R403

2001-001192 R-CARBON(S);820OHM,5%,1/2W,AB,

2001-001079 R-CARBON(S);15OHM,5%,1/2W,AB,T

4 RY801S 2002-001012 R-COMPOSITION;8.2MOhm,5%,1/2W,AA,TP,3.7X

4 R313 2003-000537 R-METALOXIDE(S);1KOHM,5%,1W,AD

4 R408 2003-000540 R-METALOXIDE(S);1KOHM,5%,2W,AD

4 R801

4 R802

4 R830

4 R831

4 R841

4 R818

4 R832

4 R419

4 R423

4 R407

2003-000586 R-METALOXIDE(S);22KOHM,5%,2W,A





2003-000998 R-METALOXIDE;300OHM,5%,2W,AF,T

2003-001035 R-METALOXIDE(S);27OHM,5%,2W,AF

2003-001040 R-METALOXIDE(S);47Kohm,5%,2W,AF,TP,3.9x1

2003-002007 R-METAL OXIDE(S);4.7KOHM,5%,2W,AF,TP,3.9

2003-002008 R-METAL OXIDE(S);18KOHM,5%,2W,AF,TP,3.9X

4 R819

4 R820

4 R821

4 R309

4 R310

2003-002064 R-METALOXIDE;7.5OHM,5%,2W,AF,T



2003-002150 R-METAL OXIDE;270OHM,5%,2W,AG,TP,6X16MM

2003-002150 R-METAL OXIDE;270OHM,5%,2W,AG,TP,6X16MM

4 R305

4 R307

2004-001371 R-METAL(S);1.5KOHM,1%,1/2W,AA,

2004-001371 R-METAL(S);1.5KOHM,1%,1/2W,AA,

4 RR401S 2004-001390 R-METAL(S);1KOHM,2%,1/2W,AA,TP

4 R834 2004-001889 R-METAL(S);127KOHM,1%,1/2W,AA,TP,2.5X6.5

4 R416 2004-001402 R-METAL(S);6.8KOHM,1%,1/2W,AA,

4 C602

4 C801

4 C802

4 C823

4 C408

4 C411

4 C413

4 C818

4 C208

4 C210

4 C403

4 R280

4 R826

4 R815

4 R413

4 R414

2004-001914 R-METAL;39KOHM,2%,1/8W,AA,TP,1

2004-001983 R-METAL;2.49KOHM,1%,1/2W,AA,TP,2.4X6.4

2008-000205 R-FUSIBLE(S);10OHM,5%,1/2W,AF,

2008-000253 R-FUSIBLE(S);0.47OHM,5%,1W,AF,

2008-000253 R-FUSIBLE(S);0.47OHM,5%,1W,AF,

4 R312

4 R308

2008-001013 R-FUSIBLE(S);1.2ohm,5%,2W,AF,TP,3.9x10mm

2008-001015 R-FUSIBLE;1.50HM,5%2WAF,TP39X10

4 CR405S 2201-000132 C-CERAMIC,DISC;100PF,10%,500V,Y5P,6X3MM,

4 C302 2201-002103 C-CERAMIC,DISC;0.015nF,5%,500V,NP0,TP,6.

4 C601 2201-000304 C-CERAMIC,DISC0.001nF,0.25pF,50V,NP0,TP

2201-000304 C-CERAMIC,DISC0.001nF,0.25pF,50V,NP0,TP

2201-000332 C-CERAMIC,AC;CK45PTAPGE250V222

2201-000332 C-CERAMIC,AC;CK45PTAPGE250V222

2201-000370 C-CERAMIC,DISC;220PF,10%,50V,Y5P,TP

2201-000556 C-CERAMIC,DISC;470PF,10%,500V,




2201-000573 C-CERAMIC,DISC;47PF,5%,50V,NPO

2201-000573 C-CERAMIC,DISC;47PF,5%,50V,NPO


Code No. Description ; Specification Remark

4 C625

4 C626

4 CE04

4 C301

4 C235

4 CE03

4 C102

4 C401

4 C621

4 C237

4 C622

4 C630

4 C634

4 C623

4 C624

4 C806

4 C245

4 C805

4 C824

4 CE02

4 C816

4 C405

4 CW04

4 C820

4 C110

4 C120

4 C603

4 C629

4 C223

4 C205

4 C242

4 C243

4 C605

4 C709

4 C221

4 C613


2201-000639 C-CERAMIC,DISC;680PF,10%,2KV,Y5P,-,5MM,T

2201-000982 C-CERAMIC,DISC;10NF,+80-20%,50

2201-000991 C-CERAMIC,HIC;CK45(T)B2KV561-K

2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2

2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2

2202-000286 C-CERAMIC,MLC-AXIAL;56PF,5%,50

2202-000286 C-CERAMIC,MLC-AXIAL;56PF,5%,50

2202-000252 C-CERAMIC,MLC-AXIAL;4.7nF,10%,50V,X7R,TP

2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50




2202-000806 C-CERAMIC,MLC-AXIAL;220pF,10%,50V,Y5P,TP

2202-000849 C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3.

2301-000108 C-FILM,PEF;1.5NF,5%,50V,6.5X3.0X5.5MM,5M




2301-000192 C-FILM,PEF;1NF,5%,50V,5.3X10MM

2301-000192 C-FILM,PEF;1NF,5%,50V,5.3X10MM

2301-000204 C-FILM,PEF;2.7NF,5%,50V,7.4X3.

2301-000224 C-FILM,PEF;22NF,5%,50V,7.4X3.9

2301-000224 C-FILM,PEF;22NF,5%,50V,7.4X3.9

2301-000224 C-FILM,PEF;22NF,5%,50V,7.4X3.9

2301-000224 C-FILM,PEF;22NF,5%,50V,7.4X3.9

2301-000232 C-FILM,PEF;3.3NF,5%,50V,8.1X4.

2301-000232 C-FILM,PEF;3.3NF,5%,50V,8.1X4.

2301-000232 C-FILM,PEF;3.3NF,5%,50V,8.1X4.

2301-000254 C-FILM,PEF;39NF,5%,50V,7.5X3.5X6.5MM,5MM

2301-000342 C-FILM,PEF;2.2nF,5%,50V,TP,7.4x3.9x13mm,

2301-000342 C-FILM,PEF;2.2nF,5%,50V,TP,7.4x3.9x13mm,

2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm



2301-000445 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm

4 C244

4 C612

4 CW05

4 C822

4 C207

4 C211

4 C220

4 C226

4 C227

4 C233

4 C402

4 C219

4 C222

4 C232

4 C240

4 C253

4 C606

4 C618

4 C632

4 C807

4 C812

4 C214

4 C215

4 C216

4 C217

4 C404

4 C204

4 C218

4 C105

4 C206

4 C209

4 C414 2301-001065 C-FILM,MPPF;47NF,55,630V,TP,19

4 CR407S 2301-001258 C-FILM,PPF;39nF,5%,400V,TP,19.5x9x15,7.5

4 C415S

4 C808

4 C306

2301-001259 C-FILM,MPPF;100nF,5%,400V,TP,19x8x16,7.5

2301-001435 C-FILM,PPF;1.5nF,5%,1.2kV,TP,15x8x12.5mm

2305-000149 C-FILM;CF922N100VT104-J-40/105

4 C305

4 C213

4 C225

4 C231

4 C236

2305-000285 C-FILM,MPEF;220NF,5%,100V,-,5M

2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM

2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM

2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM

2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM

2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM

2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM

2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM

2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM

2305-000382 C-FILM,MPEF;4.7NF,5%,400V,TP,-,5MM.

2305-000412 C-FILM,MPEF;470NF,5%,63V,-,5MM

2305-000412 C-FILM,MPEF;470NF,5%,63V,-,5MM

2305-000665 C-FILM;104J, 60V,5MM TAPING













2309-000138 C-FILM,PE-PPF;100NF,5%,50V,TP,

2401-000025 C-ALUMINUM;100uF,20%,16V,GP,TP.6.3x11,5


2401-000262 C-AL;100UF,20%,160V,GP,16X25MM,5MM,

2401-000302 C-AL;100UF,20%,25V,GP,6X11MM,5

2401-000302 C-AL;100UF,20%,25V,GP,6X11MM,5

2401-000302 C-AL;100UF,20%,25V,GP,6X11MM,5

2401-000302 C-AL;100UF,20%,25V,GP,6X11MM,5

2401-000302 C-AL;100UF,20%,25V,GP,6X11MM,5

2401-000302 C-AL;100UF,20%,25V,GP,6X11MM,5

2401-000302 C-AL;100UF,20%,25V,GP,6X11MM,5



Loc. No.

Code No.


4 L230

4 L201

4 L204

4 X601

4 L403

4 L407

4 L805

4 R816

4 LE02

4 Z202

4 J235

4 L401

4 L604

4 L605

4 L212

4 L209

4 L803

4 L601

4 L602

4 L202

4 L203

4 C819

4 L101

4 L205

4 L206

4 L603

4 LE01

4 J202

4 L707

4 L210

4 L211

4 C817

4 C407

4 C825

4 C103

4 C813

4 C229

4 C810

4 C814

4 C815

4 C631

4 C409

4 C410

4 C633

4 C635

4 C608

4 C609

4 C610

4 C611

4 C710

4 C202

4 CW02

4 CW03

4 C224

4 C234

4 C412

4 C101

4 C212

4 C615

4 C620

4 C804

4 C604

4 C619

4 C811

4 C201

4 C304

4 C303

4 C104

4 C239

4 C614

4 C607

4 C616

4 C617

4 C627

4 C809

4 C238

4 CW01

2401-000302 C-AL;100UF,20%,25V,GP,6X11MM,5

2401-000302 C-AL;100UF,20%,25V,GP,6X11MM,5

2401-000302 C-AL;100UF,20%,25V,GP,6X11MM,5

2401-000302 C-AL;100UF,20%,25V,GP,6X11MM,5

2401-000326 C-AL;100UF,20%,35V,GP,8X11MM,5

2401-000365 C-AL;100uF,20%,50V,WT,TP,10x12.5mm,

2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M

2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M

2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M

2401-000493 C-AL;10UF,20%,50V,WT,5X11MM,5M

2401-000493 C-AL;10UF,20%,50V,WT,5X11MM,5M

2401-000493 C-AL;10UF,20%,50V,WT,5X11MM,5M

2401-000493 C-AL;10UF,20%,50V,WT,5X11MM,5M

2401-000493 C-AL;10UF,20%,50V,WT,5X11MM,5M

2401-000603 C-AL;1UF,20%,50V,GP,5X11MM,5MM

2401-000603 C-AL;1UF,20%,50V,GP,5X11MM,5MM

2401-000603 C-AL;1UF,20%,50V,GP,5X11MM,5MM

2401-000603 C-AL;1UF,20%,50V,GP,5X11MM,5MM

2401-000660 C-ELECTROLYTIC;CE04WTAPG50V2.2

2401-000660 C-ELECTROLYTIC;CE04WTAPG50V2.2

2401-000927 C-AL;22UF,20%,250V,GP,13X20MM,

2401-000962 C-AL;22uF,20%,50V,GP,TP,5x11,5

2401-000962 C-AL;22uF,20%,50V,GP,TP,5x11,5

2401-001026 C-AL;3.3UF,20%,50V,GP,5X11MM,5

2401-001026 C-AL;3.3UF,20%,50V,GP,5X11MM,5

2401-001192 C-AL;33UF,20%,50V,GP,6X11MM,5MM,TP

2401-001397 C-AL;470UF,20%,25V,GP,10X16MM,

2401-001397 C-AL;470UF,20%,25V,GP,10X16MM,

2401-001914 C-AL;1uF,20%,50V,BP,TP,5x11,5

2401-001914 C-AL;1uF,20%,50V,BP,TP,5x11,5

2401-002075 C-AL;4.7uF,20%,50V,GP,TP,5x11,5mm

2401-002075 C-AL;4.7uF,20%,50V,GP,TP,5x11,5mm

2401-002075 C-AL;4.7uF,20%,50V,GP,TP,5x11,5mm

2401-002075 C-AL;4.7uF,20%,50V,GP,TP,5x11,5mm

2401-002075 C-AL;4.7uF,20%,50V,GP,TP,5x11,5mm

2401-002075 C-AL;4.7uF,20%,50V,GP,TP,5x11,5mm

2401-002215 C-AL;2200UF,20%,25V,(105RD)13X

2401-002268 C-ELEC;CE04-40/105250VT2R2-MWR

2401-002300 C-ELECTROLYTIC;CE04WTAPG50V47U

2401-002594 C-AL;220uF,20%,16V,GP,TP,8x11.5,5

2401-002594 C-AL;220uF,20%,16V,GP,TP,8x11.5,5

2401-002619 C-AL;47uF,20%,25V,GP,TP,5x11,5

2401-002619 C-AL;47uF,20%,25V,GP,TP,5x11,5

2401-003028 C-AL;100UF,20%,25V,WT,TP,6.3X1

2401-003028 C-AL;100UF,20%,25V,WT,TP,6.3X1

2401-003139 C-AL;1000UF,20%,25V,WT,TP,10*2

2401-003139 C-AL;1000UF,20%,25V,WT,TP,10*2

2701-000114 INDUCTOR-AXIAL;10UH,10%,2.5X3.







2701-000142 INDUCTOR-AXIAL;1UH,10%,2.5X3.4






2701-000159 INDUCTORAXIAL;22uH,10%,4.2x9.8mm

2701-000159 INDUCTORAXIAL;22uH,10%,4.2x9.8mm

2701-000169 INDUCTORAXIAL;3.9uH,10%,2.5x3.4mm

2701-000169 INDUCTORAXIAL;3.9uH,10%,2.5x3.4mm

2701-000177 INDUCTOR-AXIAL;33UH,10%,2.5X3.4MM



2701-000184 INDUCTOR-AXIAL;4.7UH,10%,2.5X3.4MM

2702-000142 INDUCTOR-RADIAL;22uH,5%,6x6.4mm

2801-000186 CRYSTAL-UNIT;18.432MHz,25ppm,28-AAM,8pF,

2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,-





2903-000129 FILTER-CERAMIC;BR,4.5MHz,-,-,-,TP,-

3301-000287 CORE-FERRITEBEAD;AA,3.5X1.0X6.

Remark Loc. No.

Code No.


4 J308

4 J403

4 J404

4 J405

4 J407

4 J408

4 J409

4 J410

4 J413

4 J414

4 J415

4 J285

4 J290

4 J292

4 J293

4 J294

4 J295

4 J302

4 J304

4 J305

4 J306

4 J249

4 J250

4 J251

4 J252

4 J253

4 J255

4 J256

4 J257

4 J274

4 J279

4 J223

4 J224

4 J225

4 J228

4 J231

4 J232

4 J233

4 J234

4 J236

4 J240

4 J205

4 J210

4 J211

4 J212

4 J215

4 J217

4 J219

4 J220

4 J221

4 J222

4 J103

4 J105

4 J106

4 J107

4 J108

4 J109

4 J110

4 J201

4 J203

4 J204

4 L302

4 L404

4 L402

4 L801

4 L802

4 L804







4 L806

4 L303



4 L809 3301-001223 CORE-FERRITE BEAD;AB,-,3.5X5X0.8MM,-,TP,

4 FD802S 3601-001163 FUSE-AXIAL LEAD;125V,7A,-,EPOXY,2.4X7.1M

4 FD801S 3601-001228 FUSE-AXIAL LEAD;125V,10A,FAST-ACTING,EPO

4 F801A

4 F801B

4 C203

4 J101

4 J102

3602-000114 FUSE-HOLDER;-,-,30MOHM

3602-000114 FUSE-HOLDER;-,-,30MOHM

3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A
































































Remark



Loc. No.


4 J717

4 J718

4 J719

4 J720

4 J801

4 J802

4 J808

4 J809

4 J813

4 J815

4 J630

4 J631

4 J632

4 J635

4 J636

4 J704

4 J706

4 J711

4 J712

4 J716

4 J416

4 J420

4 J601

4 J602

4 J603

4 J604

4 J616

4 J619

4 J620

4 J621

4 J624

4 J625

4 J626

4 J627

4 J628

4 J629





































4 J411

4 J412

4 R218

4 J303

4 J254

4 J423

4 J424

4 J614

4 J615

4 J703

4 J705

4 J714

4 R715

4 J237

4 J229

4 J810

4 J811

4 J307

4 02VER

4 EY301

4 EY302

4 J817

4 J820

4 J822

4 J826

4 J827

4 J828

4 J829

4 J830

4 J831

4 J832











4 J833

4 J836

4 J837

4 J841

4 J842






4 RY802S 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A

4 J803 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A

4 J804

4 J805

4 J806






















AA41-00656C PCB-MAIN;CT-29K5(QUEST),FR-1,1L,C,1.6T,3

6042-000002 EYELET;IDI.5,OD2,L3.1,SN,BSS3-E/EH
















































































4 EY839

4 EY840

4 EY841

4 EY842

4 EY843

4 EY844

4 EY845

4 EY848

4 EY850

4 EY851

4 EY855

4 EY856

4 EY857

4 EY858

4 EY862

4 EY863

4 EY864

4 EY865

4 EY866

4 EY440

4 EY441

4 EY603

4 EY604

4 EY801

4 EY802

4 EY807

4 EY808

4 EY809

4 EY810

4 EY811

4 EY814

4 EY816

4 EY824

4 EY825

4 EY826

4 EY827

4 EY830

4 EY831

4 EY832

4 EY833

4 EY838

4 EY421

4 EY423

4 EY424

4 EY425

4 EY426

4 EY427

4 EY428

4 EY429

4 EY430

4 EY431

4 EY432

4 EY433

4 EY434

4 EY435

4 EY436

4 EY437

4 EY438

4 EY439

4 EY601

4 EY602

4 EY303

4 EY304

4 EY401

4 EY402

4 EY403

4 EY404

4 EY407

4 EY408

4 EY409

4 EY410

4 EY411

4 EY412

4 EY413

4 EY414

4 EY419

4 EY420



Loc. No.

Code No.


4 EY834

4 EY835

4 EY836

4 EY859

4 EY860

4 EL401

4 EL402

4 EL403

4 EL805

4 EL806

4 EL807

4 EL808

4 EL404

4 GT102

4 GT404

4 GT801

4 GT802

4 GT803

4 GT804

4 GT805

4 EY701

4 EY702

4 EY703

4 EY704

4 EY803

4 EY804

4 EY805

4 EY806

4 EY812

4 EY813

4 EY818

4 EY819

4 EY820

4 EY821

4 EY822

4 EY823






















6042-000001 EYELET;ID2.2,OD2.7,L3.1,SN,BSS3-E/EH








AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO







4 GT806

4 L/LINE

4 R418

4 CE01

4 DE03

4 RE02

4 RE05

4 RE09

4 RE10

4 R902

4 R905

4 SW202

4 SW203

4 SW204

4 SW205

4 SW206

3 X201

3 CN301

2 A/CRT

3 DF01


AA68-01544A LABEL;LINE,ALL MDL COMMON

2008-000266 R-FUSIBLE(S);1OHM,5%,2W,AF,TP,

2401-002597 C-AL;220uF,20%,35V,GP,TP,10x12.5,5

0403-001325 DIODE-ZENER;MTZJ15C,14.35-15.09V,500mW,D

2001-001178 R-CARBON(S);680OHM,5%,1/2W,AA,

2004-001397 R-METAL(S);4.7KOHM,1%,1/2W,AA,

2008-001018 R-FUSIBLE(S);0.47OHM,10%,2W,AF

2004-004048 R-METAL(S);3.9Kohm,1%,1/2W,AA,TP,2.5x6.5



3404-000244 SWITCH-TACT;15V,20MA,90-170GF,





2801-004033 CRYSTAL-UNIT;12MHZ,30PPM,28-AAM,30PF,30O

AA60-40012D PIN-GT,ASSY;4P,T1.6,6-12.5-14MM,NYLON66

AA96-01015A ASSY MISC P-CRT;TXM2792FX,K57A


3 DF04

3 DG01

3 D504

3 D514

3 D515

3 D516

3 D517

3 D518

3 D519

3 DF02



0402-000254 DIODE-RECTIFIER;RGP10J,600V,1A,DO-41

0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,







3 DF03

3 DZF01

3 DZF02

3 DZ501

3 DZ502


0403-001039 DIODE ZENER;MA2560,56V,52-60V,1W,DO-41,T

0403-001039 DIODE ZENER;MA2560,56V,52-60V,1W,DO-41,T



3 DZ503

3 DZ504



3 DZ507 0403-001325 DIODE-ZENER;MTZJ15C,14.35-15.09V,500mW,D

3 DZG501 0403-001328 DIODE-ZENER;MTZJ22A,20.15-21.20V,500mW,D

3 QG01

3 QF03


0501-000369 TRANSISTOR;KSC2331-Y(TAPG)

Remark Loc. No.

3 C515

3 CF10

3 CF12

3 L501

3 L508

3 LF02

3 L504

3 L507

3 L509

3 LF04

3 LF05

3 CG02

3 CF07

3 C514

3 CG03

3 CF14

3 CG01

3 CG04

3 CF11

3 C510

3 C520

3 R522

3 CF01

3 CF03

3 CF06

3 CF08

3 CF04

3 C509

3 C512

3 CF02

3 CF05

3 RF19

3 RF20

3 RF21

3 RF22

3 RG01

3 RG03

3 RG02

3 RG04

3 R523

3 R519

3 RF13

3 RF16

3 R512

3 R515

3 R518

3 R521

3 RF18

3 RF23

3 RF24

3 RF25

3 RF07

3 R548

3 RF14

3 RG06

3 RG07

3 RF17

3 RF15

3 RF06

3 RG05

3 RG08

3 QF01

3 QF02

3 RF09

3 RF12

3 RF10

3 RF11

3 RF08

3 RF26

3 RF03

3 RF05

3 RF02

3 RF01

3 RF04

3 R509

3 R511

3 R517

Code No.


















2001-000904 R-CARBON;620OHM,5%,1/8W,AA,TP,1.8X3.2MM

2001-001062 R-CARBON(S);10MOHM,5%,1/2W,AA,


2001-001100 R-CARBON(S);2.7OHM,5%,1/2W,AA,

2001-001100 R-CARBON(S);2.7OHM,5%,1/2W,AA,

2001-001100 R-CARBON(S);2.7OHM,5%,1/2W,AA,

2001-001100 R-CARBON(S);2.7OHM,5%,1/2W,AA,

2001-001107 R-CARBON(S);220OHM,5%,1/2W,AA,

2001-001163 R-CARBON(S);560OHM,5%,1/2W,AA,

2001-001163 R-CARBON(S);560OHM,5%,1/2W,AA,



2002-001008 R-COMPOSITION;1.8KOHM,10%1/2W,AA,TP,3.7



2002-001009 R-COMPOSITION;2.7KOHM,10%,1/2W,AA,TP,3.7

2003-000458 R-METALOXIDE(S);100OHM,5%,2W,A

2003-000746 R-METALOXIDE(S);56OHM,5%,2W,AD

2003-000746 R-METALOXIDE(S);56OHM,5%,2W,AD



2003-002214 R-METALOXIDE(S);680ohm,5%,2W,AG,TP,3x19



2004-001397 R-METAL(S);4.7KOHM,1%,1/2W,AA,

2004-001987 R-METAL;4.3KOHM,1%,1/2W,AA,TP,

2004-002022 R-METAL,FILM;RM1/2T51K-F

2004-002022 R-METAL,FILM;RM1/2T51K-F

2008-001018 R-FUSIBLE(S);0.47OHM,10%,2W,AF

2008-000299 R-FUSIBLE;RF2RT470-J

2008-001129 R-FUSIBLE(S),1.5OHM,5%1/2W,AF,TP,2.5

2201-000370 C-CERAMIC,DISC;220PF,10%,50V,Y5P,TP

2201-000376 C-CERAMIC,DISC;220PF,5%,50V,SL,4X4MM,5MM

2201-000516 C-CERAMIC,DISC;4.7NF,+100-0%,5

2201-000604 C-CERAMIC,DISC;56PF,+100-0%,50

2201-000653 C-CERAMIC,DISC;68PF,5%,50V,SL,4.0X3.5MM,

2201-000723 C-CERAMIC,DISC;4.7nF,20%,3KV,Y5U,TP,16x5

2301-000192 C-FILM,PEF;1NF,5%,50V,5.3X10MM

2301-000192 C-FILM,PEF;1NF,5%,50V,5.3X10MM

2301-000261 C-FILM,PEF;4.7NF,5%,100V,10.5X

2305-000149 C-FILM;CF922N100VT104-J-40/105

2305-000704 C-M,POLYESTER;CFS922MTAPG250V1

2401-000430 C-ELECTROLYTIC;CE04WTAPG250V10

2401-000493 C-AL;10UF,20%,50V,WT,5X11MM,5M

2401-000832 C-AL;220UF,20%,25V,GP,8X11MM,5

2401-000832 C-AL;220UF,20%,25V,GP,8X11MM,5

2401-000832 C-AL;220UF,20%,25V,GP,8X11MM,5

2401-000927 C-AL;22UF,20%,250V,GP,13X20MM,

2401-001232 C-AL;4.7UF,20%,250V,GP,10X12.5

2401-001232 C-AL;4.7UF,20%,250V,GP,10X12.5

2401-001563 C-AL;47uF,20%,400V,GP,TP,16x25mm,7.5



2701-000112 INDUCTOR-AXIAL;100UH,10%,2.8X7



2701-000115 INDUCTOR-AXIAL;10UH,10%,2.8X7M

2701-000115 INDUCTOR-AXIAL;10UH,10%,2.8X7M






Loc. No.


3 J524

3 J529

3 J530

3 JF02

3 JF06

3 JG01

3 JG02

3 R502

3 R503

3 R504

3 R510

3 01VER

3 EY501

3 EL81

3 EL82

3 EL83

3 EL84

3 EL85

3 EL86

3 EL87

3 LF06

3 LF07

3 LF01

3 J501

3 J503

3 J508

3 J509

3 J510

3 J511

3 J512

3 J513

3 J515

3 J516

3 J521

3 J522

3 J523




























AA41-00683B PCB-CRT;CT-29M6V/CT-29U1,FR-1,1L,B,1.6T,









3 EL88

3 EL89

3 EL90

3 EL93

3 EL94

3 EL95

3 EL96

3 EL79

3 EL80

3 GT504











3 GT505

3 GT506

3 ICG01

3 VA999

3 JA501



1201-000191 IC;MC4558C

3704-000114 SOCKET CRT;14P,29.1,35.5SN,1SH09S/BK

3722-001503 JACK-PIN;1P,1PI,NI,RED,SCR-JACK

3 CN502E AA39-20027B LEAD CONNECTOR-ASSY;,6P,67096-006,S,400,

3 CN501E AA39-20031D LEAD CONNECTOR-ASSY;,9P,67096-009,S,500,

3 QF04

4

4

AA96-00243L ASSY H/S;-,CRT,AA62-00045A,2SC2344,HERC


0502-000153 TR-POWER;2SC2344-D,NPN,180V,16

4

4

3 QF05

4

4

4

4

3 IC501

4

4



AA96-00243M ASSY H/S;-,AMP,AA62-00045A,2SA1011,HERC


0502-000131 TR-POWER;2SA1011-D,PNP,-180V,-



AA96-50311E ASSY-H/S;-,-,AA62-30175D,TDA6108Q,-

1201-001330 IC-VIDEO;TDA6108JF,ZSIP,9,SINGLE,-

6003-000334 SCREW-TAPTITE;RH,+,2S,M3,L6,ZP

4

3 WG2

AA62-30175D HEATSINK-PS;-,SECC,T1.0,-,33X15X30FT-2

AA39-20010B LEAD-CONNECTOR,ASSY;-,YFH800-01,500MM,1P

3 CN501A 3711-002648 POST-HEADER;67094-009(AUTO)

3 CN502A 3711-002645 POST-HEADER;67094-006(AUTO)

3 CNG01 3711-002643 POST-HEADER;YW025-04(AUTO)

3 CNF01

3 QG02

3 QG03

3 BAND

3 C516

3 C507

3711-002642 POST-HEADER;67094-003(AUTO)

0502-000244 TR-POWER;KSA940,PNP,-150V,-150

0502-001007 TR-POWER;KSC2073-H2,NPN,150V,1

AA63-10002A BAND-TIE;-,NYLON66V2,-,-,L100,NTR,-,-

2301-000213 C-FILM,PEF;220NF,5%,250V,21.5X

2301-000213 C-FILM,PEF;220NF,5%,250V,21.5X

2 S/FELT

1 A/CFRONT AA90-03190X ASSY COVER FRONT;CL29K5MQKX/XAX

2 CWFCL

2 APAVS

3 R701

3 R702

3 C701

3 C702

3 C703

3 C704

3 C705

3 C706

3 L701

3 L702

3 L703

3 L704

3 L707

3 L708

3 00VER

3 JH701

3 JA701

3 CN704

3 CN701

3 CN703

3 BAND

2 L/SPK

2 SPK+CF 6006-001095 SCREW-ASS’Y TAPT;WP,BH,+,M4,L12,ZPC(YEL)

2 CRT+CF AA60-10050V SCREW-ASSY;WC,HH,+,M6,L30,SWRCH18A,ZPC(S

2 AV+CF 6003-001268 SCREW-TAPTITE;TH,+,B,M4.0,L12.0,ZPC(YEL)

2 F/C AA96-00906S ASSY COVER P-FRONT;29K5,XAX,HIPS HB,G430

3 TAPE

3 KC+CF

3 WR+CF

3 MASK

0203-001085 TAPE-DOUBLE FACE;#4929,T0.64,W12,-,BLK

6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR

6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR

AA60-00091G SPACER-FELT;-,FELT,200X10,-,-,BLK,T0.5,-

3 SPRING AA61-60003J SPRING ETC-CS;-,SUS304,-,-,OD6,N7,OD6,-,

3 WR

3 KP

3 KC

3 CF

2 AHS

2 L/QMS

2 INLAV

2 BADGE

2 SP

2 CWFCR

AA64-02632A WINDOW-RMC,LED;29K5,PC,CLR

AA64-02629A KNOB-POWER;29K5,ABS HB,G3676,SVM-3012

AA64-02635A KNOB-CONTROL;29K5,ABS HB,G3676,SVM-3012

AA64-03418B CABINET FRONT;29K5,HIPS,HB,G4309,SV012 K

AA91-00507A ASSY HOLDER SPK;-,-,8OHM/15W,-,ASSY HOLD

AA68-02391A LABEL-QMS;ART-PAPER(90)G,110x24mm

AA64-01506C INLAY-AV;29K3,PVC-SHEET,T0.3,-,P/GRAY,-

AA64-70117B BADGE-BRAND;-,AL,-,-,L65,R2000,SILVER,SS

AA61-40113A STOPPER-PCB;-,ABS,HB,NTR.

AA65-00011C CLAMP-WIRE;ALL MODEL,NYLON 66,V2,NTR,25M

AA65-00011B CLAMP-WIRE;ALL MODEL,NYLON 66,V2,NTR,15M

AA96-01156A ASSY MISC,A/V SIDE,CFT2791KX/SMS;K57A

2001-000028 R-CARBON(S);100OHM,5%,1/2W,AB,

2001-000028 R-CARBON(S);100OHM,5%,1/2W,AB,



2202-000231 C-CERAMIC,MLC-AXIAL;330PF,10%,50V,Y5P,3.

2202-000231 C-CERAMIC,MLC-AXIAL;330PF,10%,50V,Y5P,3.

2401-002009 C-AL;100UF,20%,16V,GP,TP,6.3X7

2401-002009 C-AL;100UF,20%,16V,GP,TP,6.3X7







AA41-00345A PCB-SIDE A/V;CS29K1,FR-1,1L,A,1.6T,245x2

3722-000143 JACK-PHONE;1P,3.4MM,-,MBAG

3722-001031 JACK-RCA;3P,3.6MM,#18,AU

AA39-00070A LEAD CONNECTOR-ASSY;4P,200mm,YBNH250-04,

AA39-20068E LEAD CONNECTOR-ASSY;-,YBNH025-08,67096-0

AA39-20069C LEAD CONNECTOR-ASSY;,5P,YBNH025-05,67096

AA63-10002A BAND-TIE;-,NYLON66V2,-,-,L100,NTR,-,-

AA65-30018A CLAMP-WIRE;-,NYLON6.6,-,-,DATL

1 A/CREAR AA90-04694A ASSY COVER REAR;29K5,K57A,LATIN

2 CB+RCA 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR

2 CB+CF 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR

2 SPCBC

2 C/B

2 AC+BC

AA60-00091J SPACER-FELT;-,FELT,330X10,-,-,BLK,T0.5,-

AA64-03417B CABINET BACK;29K5,HIPS,HB,G4309

AA65-30008A CLAMP-CORD;-,PE,HB,BLK,-,-

2 INB

2 FBT

AA64-00892G INLAY BACK;D2,D3,RCA9P+S-VHS+DVD,PS SHEE

AA65-30018A CLAMP-WIRE;-,NYLON6.6,-,-,DATL

2 YUGO AA65-30018A CLAMP-WIRE;-,NYLON6.6,-,-,DATL

2 DRESA/V AA65-30018A CLAMP-WIRE;-,NYLON6.6,-,-,DATL

2 L/RAT AA68-02292A LABEL-RATING;TROJAN,ART PAPER 90,60X90mm

1 A/BOX

2 L/BOX

2 PCK


AA63-00362A FELT;W25XL8,T2.0,FELT,BLK.

ASSY COVER FRONT

ASSY COVER REAR

ASSY BOX

AA92-05174X ASSY BOX;CL29K5MQKX/XAP

AA68-01542A LABEL;(UNIBOX),PAPER WHT ALLMD

AA69-02178B PACKING CASE;29K5(SAMEX),D-4 AB,A1,YEL,A



Loc. No.

Code No.


ASSY P/MATERIAL

1 A/PMATERI AA92-05179C ASSY P/MATERIAL;TXN2730FX/XAA

2 BXTAPE 0203-001295 TAPE-OPP MASKING;1242,T0.06,W100,L91.4M,

2 STAPLE AA60-40006A PIN-STAPLE;-,-,-,H18,33X17.8X2

2 C/SET AA69-01605A CUSHION-SET;29K5,PS FOAMED,C=0.02

2 PE-BAG AA69-01209A BAG;SHEET,25-27,W54,L60,FOAM,OEM.

Remark Loc. No.

ASSY CPT

1 A/CPT AA91-06401A ASSY CPT;29K5,K57A,A68QCP891

2 D-COIL

2 A/TBC

AA27-00215A COIL DEGAUSSING;,29INCH,10%,50T,4.5OHM,2

AA98-70011A ASSY-TBC,WIRE(P);-,29,NTSC,PAL,2P

2 CRT AA03-00273A CRT COLOR;A68QCP891X100 ,380MG,1.11MH,14

2 C/CORE AA65-00019A CLAMP CORE-D,COIL;25-34,NYLON 66,V2,NTR

2 S/GUM AA63-60004L SPACER-GUM,CRT;-,NTR RUBBER,-,-,-,BLK,T3

2 INL/CRT AA64-03072A INLAY-COVER;PS-SHEET,50X30,T.1.0

ASSY ACCESSORY

1 A/ACCS AA92-07703E ASSY ACCESSORY;CL29K5MQKX/XAP,K57A

2 AC-TAPE 0203-001279 TAPE-OPP MASKING;#232,T0.14,W15,L50000,Y

2 RMT AA59-00302F REMOCON;,TM58,SSM174PT,41,SS,L/GRAY,MBR,

2 I/B

2 I/B2

AA68-02838A MANUAL USERS;K57A,SPA,W/P100(G)

AA68-02839A MANUAL USERS;K57A,ENG,W/P100(G)

2 C/WARR AA68-00987A CARD WARRANTY;W/P100,A4,1P,SELA

2 BAG

2 BATT

2 C/RCA

2 PLUG

AA69-01195A BAG PE;CL29A6W8X,HDPET0.012,93/4X151

4301-000120 BATTERY-MN;1.5V,-,AA

AA39-40001B PATCH-CORD;3P-3P1500MMRED,WHT,YEL,500

3721-000136 PLUG-CONVERSION;15A300VPI4.0CP

Code No.



8. Block Diagram

8-1 K57A

SOUND AMP

( TDA7297S 15W2CH )

SPEAKER

TUNER VI F SAW

SI F SAW

8 V 5 V

REGUL ATOR I C

KA7632

3. 3 V

M a i n-

Tr ans

AUDIO SIGNAL

PROCESSING

(MSP3425G)

S I F - OUT

Swit c h i ng I C

( STR KA5Q1265R)

B r i d ge Di ode

R ela y

120V/ 220V

Monit or out

AV- 2 i nput

AV- 1 i nput

S- V i deo Y

Pb

Pr

S I F

S I GNAL

P I F

S I GNAL

R G B

CRT DR I VE (TDA6108JF )

VMC(C2344/ A1011)

CRT

DY

HV

UOC P l u s I C

( TDA 9592)

EEPROM

( X24C08P)

H -OUT TR

D5703

RMC

KEY CONTROL

33V

200V

VERTIC AL

( L A7845)

+16. 5 V / - 14 V

HEATER

F BT

F UH- 29A001B

Block Diagram

8-1

9. Wiring Diagram

9-1 K57A

POWER

CORD

CN902

4 3 2 1

CN901

3 2 1

CRT PCB

Wiring Diagram

Samsung Electronics

CN502

B-13.5V

B+16.5V

HEATER

GND

N.C

B+ 210V

CN501

GND

SVM-OUT

GND

TILT

SENSE

GND

B- OUT

G- OUT

R- OUT

CN701

V-OUT

GND

V- IN

GND

L -OUT

R- OUT

L- IN

R- IN

CN702

SY-OUT

GND

SC-OUT

GND

SY-IN

GND

SC-IN

9-1

9-2

MEMO

10. Schematic Diagrams

10-1 MAIN(1/3)

TP13

TP14

TP15

TP16

TP17 TP18

TP19 TP21

TP22

TP23

Schematic Diagrams

TP13 TP14

TP15 TP16

TP17 TP18

TP19 TP21

TP22 TP23


Schematic Diagrams

10-2 MAIN(2/3)

10-2

TP01

TP02

TP12

TP05

TP06

TP03

TP04

TP7

TP10

TP01

TP03

TP02

TP04

TP05 TP06

TP07 TP08

TP10 TP12

TP08

Samsung Electronics

10-3 MAIN(3/3)

Samsung Electronics

TP24

Schematic Diagrams

TP24

10-3

Schematic Diagrams

10-4 CRT


Samsung CL29K5MQ Specifications

COLOR TELEVISION RECEIVER

Chassis : K57A(N)

Model : CL29K5MQKX/XAP

COLOR TELEVISION RECEIVER CONTENTS

1.

Precautions

2.

Specifications and IC Data

3.

Disassembly and Reassembly

4.

Alignment and Adjustment

5.

Troubleshooting

6.

Exploded View and Parts List

7.

Electrical Parts List

8.

Block Diagram

9.

Wiring Diagram

10.

Schematic Diagrams

ELECTRONICS

© Samsung Electronics Co., Ltd. MAY . 2003

Printed in Korea

AA82- 00622A

1. Precautions

1-1 Safety Precautions

1-1 Safety Precautions (Continued)

1-2 Servicing Precautions

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

CAUTION

2. Specifications and IC Data

2-1 Specifications

2-2 IC Line Up

2-3 Semiconductor Base Diagrams

3. Disassembly and Reassembly

3-1 Back Cover Removal

3-2 Main Board Removal

3-3 Speaker Removal

3-4 CRT Removal

4. Alignment and Adjustments

4-1 Preadjustment

4-1-1 Factory Mode

4-1-2 When EEPROM (IC202) Is Replaced

4-2 Factory/Service Mode

4-2-1 Procedure for the “Adjustment” Mode

4-1-3 When CRT Is Replaced

4-2-2 Main Adjustment Parameter

4-2-3 Option Bytes

Option Table : xx xx

4-2-4 RESET

4-3 Other Adjustments

4-3-1 General

4-3-2 Automatic Degaussing

4-3-3 High Voltage Check

4-3-4 FOCUS Adjustment

4-3-5 Cathode Voltage Adjustment

(Screen Adjustment)

4-3-6 Purity Adjustment

4-3-7 White Balance Adjustment

→

→

4-3-8 Center Convergence Adjustment

4-3-9 RF AGC Adjustment

4-3-10 Sub-Color Adjustment

4-3-11 Geometry Adjustment

5. Troubleshooting

5-1 No Power

5-2 No Video (Sound OK)

5-3 No Sound (Video OK)

5-4 Horizontal Lines Appear or Screen

6. Exploded View & Parts List

7. Electrical Parts List

7-1 CL29K5MQKX/XAP

ASSY CHASSIS

ASSY COVER FRONT