Samsung CS21K5 Specifications

Television Video Cassette Recorder

Chassis : C17A (TS-10 )

Model : TW20P14X/BWT

Television Video Cassette Recorder CONTENTS

1.

Precautions

2.

Specifications

3.

Disassembly and Reassembly

4.

Alignment and Adjustment

5.

Troubleshooting

6.

Exploded View and Parts List

7.

Electrical Parts List

8.

Block Diagram

9.

Wiring Diagram

10.

Schematic Diagrams

ELECTRONICS

©

Samsung Electronics Co., Ltd. Feb. 2003

Printed in Korea

AA82-00423A

Precautions

1. Precautions

Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.

1-1 Safety Precautions

1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields.

2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers.

3. Make sure that there are no cabinet openings through which people—particularly children—might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers.

If the measured resistance is less than 1.0

megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer.

4. Leakage Current Hot Check (Figure 1-1):

Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards

Institute (ANIS C101.1, Leakage Current for

Appliances), and Underwriters Laboratories

(UL Publication UL1410, 59.7).

5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit’s AC switch first in the

ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.

DEVICE

UNDER

TEST

TEST ALL

EXPOSED METAL

SURFACES

3-WIRE CORD

ALSO TEST WITH

PLUG REVERSED

(USING AC ADAPTER

PLUG AS REQUIRED)

LEAKAGE

CURRENT

TESTER

(READING SHOULD

NOT BE ABOVE

0.5mA)

EARTH

GROUND

Fig. 1-1 AC Leakage Test

6. Antenna Cold Check:

With the unit’s AC plug disconnected from the

AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector.

7. X-ray Limits:

The picture tube is especially designed to prohibit X-ray emissions. To ensure continued

X-ray protection, replace the picture tube only with one that is the same type as the original.

Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection.

8. High Voltage Limits:

High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced.

(X-ray protection circuits also may be called

“horizontal disable” or “hold-down”.)

Heed the high voltage limits. These include the X–ray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.

Samsung Electronics 1-1

Precautions

1-1 Safety Precautions (Continued)

9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components.

10. Design Alteration Warning:

Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer’s warranty.

11. Hot Chassis Warning:

Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the

AC source.

To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert.

Re-measure the voltage between the chassis and ground.

12. Some TV chassis are designed to operate with

85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source.

13. Some TV chassis have a secondary ground system in addition to the main chassis ground.

This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered.

14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards.

1-2

15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts.

16. Picture Tube Implosion Warning:

The picture tube in this receiver employs

“integral implosion” protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original.

17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some

“in-line” picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such “permanently attached” yokes from the picture tube.

18. Product Safety Notice:

Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection.

These safety features and the protection they give might be lost if the replacement component differs from the original—even if the replacement is rated for higher voltage, wattage, etc.

Components that are critical for safety are indicated in the circuit diagram by shading,

Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications.

A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.

Samsung Electronics

Precautions

1-2 Servicing Precautions

Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions.

Warning2: An electrolytic capacitor installed with the wrong polarity might explode.

1. Servicing precautions are printed on the cabinet. Follow them.

2. Always unplug the unit’s AC power cord from the AC power source before attempting to: (a)

Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor.

3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.

4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged.

5. Check the insulation between the blades of the

AC plug and accessible conductive parts

(examples: metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (430V) to the blades of the AC plug.

The insulation resistance between each blade of the AC plug and accessible conductive parts

(see above) should be greater than 1 megohm.

7. Never defeat any of the B+ voltage interlocks.

Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.

8. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last.


Precautions

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

1. Some semiconductor (“solid state”) devices are easily damaged by static electricity. Such components are called Electrostatically

Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity.

2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power— this is an electric shock precaution.)

3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge.

4. Do not use freon-propelled chemicals. These can generate electrical charges that damage

ESDs.

5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs.

6. Use only an anti-static solder removal device.

Many solder removal devices are not rated as

“anti-static”; these can accumulate sufficient electrical charge to damage ESDs.

7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.

8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.

1-4 Samsung Electronics

2. Specifications

The descriptions and characteristics given in this booklet are given for information purposes only and are subject to modification without notice.

TELEVISION PART

Colour systems

TV standards

Number of channels

Reception range/cable TV

Aerial input

VCR PART

Format

Heads

Luminance

Colour

FF/REW time

Wow and flutter (WTD)

Frequency response

GENERAL

Power supply

Consumption

Audio output power

Number of loudspeakers

Tube size

Tube type

Sockets

Dimensions (W x D x H)

Weight

Operating temperature

Relative humidity

PAL(option) / SECAM(option) (UK;PAL)

L/L’(option), B/G(option), D/K(option) (UK;I)

100 programmes

Hyperband/interband tuner

75 Ohms, coaxial cable

VHS standard

(PAL / SECAM(option) / MESECAM(option) / NTSC in playback only)

Video: 2 rotary heads, LP(option), 4 Heads(option)

Audio/Control: 1 stationary head (linear)

Erase: 1 full track erase head

System Video Normal CCIR

System Audio

FM azimuth recording

Mono / NICAM&A2-STEREO

Down converted subcarrier phase shifted direct recording

Less than 100 seconds in FF with E-120

0.4% maximum (SP)

100 Hz - 8 KHz

220-240V~, 50Hz (110-260V~, 50/60Hz; option),(160-300V~50/60Hz;Russia)

14”15” (50W)

20”/21” (60W)

14”15” (2W)

20” (2W)

21” (1.0Watts x 2)

14”/15”/20” (1)

21” (2)

14” (37cm/34cmV)

15” (39cm/36cmV)

20” (51cm/48cmV)

21” (55cm/51cmV)

BLACK MATRIX

1 full RGB SCART on the rear

1 RCA input (audio and video) on the front

Earphones output (3.5 mm mini-jack)

1 aerial/cable TV coaxial input

14” (368 x 390 x 381)

15” (411 x 401 x 417)

20” (486 x 473 x 485)

21” (520 x 495 x 508)

14” (11.1 kg)

15” (14.8 kg)

20” (19 kg)

21” (23.4 kg)

5°C - 40°C (41°F - 104°F)

10% - 75%


MEMO


Alignment and Adjustments (Electrical)

4. Alignment and Adjustments (Electrical)

4-1 Preadjustment

4-1-1 Factory Mode

1. Do not attempt these adjustments in the Video

Mode.

2. The Factory Mode adjustments are necessary when either the EEPROM (IC902) or the CRT is replaced.

3. Do not tamper with the “Adjustment” screen of the Factory Mode menu. This screen is intended only for factory use.

4-1-3 When CRT Is Replaced

Make the following adjustments after setting up purity and convergence:

White Balance

Sub-Brightness

Vertical Center

Vertical Size

Horizontal Size

4-1-2 When EEPROM (IC902S) Is Replaced

1. When IC902 is replaced all adjustment data revert to initial values. It is necessary to reprogram this data.

2. After IC902 is replaced, warm up the TV for

10 seconds.

4-2 Factory (“Service”) Mode

4-2-1 Procedure for the “Adjustment” Mode

1. This mode uses the standard remote control.

The Service Mode is activated by: (1) pressing the “FACTORY” service key on the local-keyboard, or (2) by entering the following remotecontrol sequence (within 2 seconds):

STAND-BY →DISPLAY →MENU→ MUTE→

POWER ON

2. The “SERVICE (FACTORY)” message will be displayed. The Service Mode has three components: Adjustment, Option and Reset.

3. Access the Adjustment Mode by pressing the

“VOLUME” keys ( Up or Down). The adjustment parameters are listed in the accompanying table, and selected by pressing the CHAN-

NEL keys ( ▲,▼).

4. Selection sequences for the

PAL/SECAM B/G, L/systems: down or up key:

AGC>TXP>AFW>SBT>SCT>SCR>STT>RG>

GG>BG>TCT>SC>SL>PVS>PHS>NVS>

NHS>CDL>BKS

5. The VOLUME keys increase or decrease the adjustment values, (stored in the non-volatile memory) when Adjustment Mode is cancelled.



4-2-2 Main Adjustment Parameters

BLR

BLB

AGC2T

PF

RP

YD

CDL

SCL

PWL

OMD

PVS

PHS

NVS

NHS

OSD ABBREVIATION

AGC

XP

QSS

SBT

SCT

SCR

TCT

SC

SL

VA

STT

RG

GG

BG

RANGE

63

7

1

23

23

13

13

63

63

63

1

63

63

63

63

63

63

63

15

3

15

63

63

63

31

3

3

15

NOTE : PVS, PVA, PHS, NVS, NVA,NHS parameters must be aligned using both the 50 Hz and 60 Hz vertical-field rates.

31

27

15

2

2

5

12

26

4

1

27

40

38

22

0

11

30

38

9

38

32

32

INITIAL DATA

28

5

10

6

1

6

4-2-3 AGING Mode (Reference Only)

This pattern is used for pre-heating the CRT during manufacturing--it is accessed in the factory by twice pressing the "FACTORY" key .

Even if the TV power is cut off, the Aging Mode is not cancelled.

The "AGING" marking is displayed on the screen.

The AGINGmode is cancelled by repressing the "FACTORY" key.


4-2-4 Option

5

6

3

4

BYTE

1

2

7

8

9

4-3 Reset

5

6

3

4

BYTE

1

2

7

8

9

ITEM

Contrast

Bright

Sharpness

Color

Tint

Volume

Program Number

Color System

Sound System

3DB LNA

Panel Lock

Language

Clock

Timer

On Time

Sleep

PICTURE MODE

ITEM

LANGUAGE

SYSTEM

TUNER

HELP MESSAGE

VCR HEAD

G-CODE

ATS OPTION

VPS/PDC

TTX


0

EUROPE/URSSIA

CF/CI/CW/CX/CB/CII

1/2

ON/OFF

2HD/2HDLP/4HD/HIFI

SHOWVIEW/VIDEO PLUS/NONE

ON/OFF

PDC/VPS/NONE

ON/OFF

0



4-4 Other Adjustments

4-4-1 General

1. Usually, a color TV needs only slight touch-up adjustment upon installation.

Check the basic characteristics such as height, horizontal and vertical sync and focus.

2. The picture should have good black and white details. There should be no objectionable color shading; if color shading is present, perform the purity and convergence adjustments described below.

3. Use the specified test equipment or its equivalent.

4. Correct impedance matching is essential.

5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the

TV. When inserting signal markers, do not allow the marker generator to distort test results.

6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate.

7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.

8. To protect against shock hazard, use an isolation transformer.

4-4-2 Automatic Degaussing

A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation.

The degaussing coil operates for about 1 second after the power is switched ON. If the set has been moved or turned in a different direction, disconnect its AC power for at least

10 minutes.

If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil.

Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before removing power.

4-4-3 High Voltage Check

CAUTION: There is no high voltage adjustment on this chassis. The B+ power supply must be set to +125 volts (Full color bar input and normal picture level).

1. Connect a digital voltmeter to the second anode of the picture tube.

2. Turn on the TV. Set the Brightness and

Contrast controls to minimum (zero beam current).

3. The high voltage should not exceed 27.5KV.

4. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 27.5KV under any conditions.



4-4-4 FOCUS Adjustment

1. Input a black and white signal.

2. Adjust the tuning control for the clearest picture.

3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen.

4-4-5 Screen Adjustment

1. Turn to the ACTIVE channel.

2. Adjust the VR screen for a normal picture is (no blooming or flyback line).

3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen.

4-4-6 Purity Adjustment

1. Warm up the receiver for at least 20 minutes.

2. Plug in the CRT deflection yoke and tighten the clamp screw.

3. Plug the convergence yoke into the CRT and set in as shown in Fig. 4-1.

4. Input a black and white signal.

5. Fully demagnetize the receive by applying an external degaussing coil.

6. Turn the CONTRAST and BRIGHTNESS controls to maximum.

7. Loosen the clamp screw holding the yoke. Slide the yoke backward or forward to provide vertical green belt. (Fig. 4-2).

8. Tighten the convergence yoke.

9. Slowly move the deflection yoke forward, and adjust for the best overall green screen.

10. Temporarily tighten the deflection yoke.

11. Produce blue and red rasters by adjusting the low-light controls. Check for good purity in each field.

12. Tighten the deflection yoke.



6 Pole Magnet

Clamper

Screw

4 Pole Magnet

2 Pole Magnet

2 POLE

PURITY

Fig. 4 -1 Convergence Magnet Assembly

YOKE

CLAMP

SCREW

6 POLE

CONVERGENCE

4 POLE

CONVERGENCE

Vertical Green Belt

ADJUST

(VERTICA

31m/m

4-4-7 White Balance Adjustment

4-4-7 (A) HIGH-LIGHT ADJUSTMENT

1. Input either a Lion Head or a “pure white” pattern.

2. Warm up the TV for 30 minutes.

3. Check the data in the Service Mode

4. Adjust RG, BG in the Factory Mode.

4-4-7 (B) LOW-LIGHT ADJUSTMENT

1. Automatically accomplished during the high-light adjustment.

4-6

Fig.4-2 Center Convergence Adjustment

Samsung Electronics

4-4-8 Center Convergence Adjustment

1. Warm up the receiver for at least 20 minutes.

2. Adjust the two tabs of the 4 pole magnets to change the angle between them. Superimpose the red and blue vertical lines in the center area of the screen.

3. Adjust the Brightness and Contrast controls for a well defined picture.

4. Adjust the two-tab pairs of the 4 pole magnets, and change the angle between them.

Superimpose the red and the blue vertical lines in the center area of the screen.


5. Turn the both tabs at the same time, keeping the angle constant, and superimpose the red and blue horizontal line in the center of the screen.

6. Adjust the two-tab pairs of the 6-pole magnets to superimpose the red and blue line onto the green. (Changing the angle affects the vertical lines, and rotating both magnets affects the horizontal lines.)

7. Repeat adjustments 2~6, if necessary.

8. Since the 4-pole magnets and 6-pole magnets interact, the dot movement is complex

(Fig. 4-3).

BLUE RED

RED/BLUE GREEN

BLUE

RED

RED/BLUE

GREEN

4-Pole Magnet Movement

Fig 4-3 Center Convergence Adjustment

4-4-9 Dual Tuner AFT Adjustment

Test Equipment

1. TV Generator(PM5518, PM5418, ETC)

2. DC VOLTMETER

1. Connect DC Voltmeter to AFT terminal of TUNER IF-MODULE.

2. After selecting P00, input to IF1 terminal of TU002(38.9 MHz Using PM5518)

3. After selecting P00, set to 2.5V±0.2V(Using FRANCE : T101, PAL/SCAM B/G,I,D/K : L102)

6-Pole Magnet Movement



4-5 Electrical Adjustment (VCR Section)

4-5-1 Preparation

Electrical adjustments are required after replacing circuit components and certain mechanical parts.

It is important to perform these adjustment only after all repairs and replacements have been com pleted. Also, do not attempt these adjustments unless the proper equipment is available.

4-5-2 Required Test Equipment

1. Color Television or Monitor

2. Oscilloscope : Wide-band, dual-trace, triggered delayed sweep.

3. DC Voltmeter

4. TV CH Generator

5. Attenuator

6. Recording tape. (Blank tape)

7. Pattern Generator : PAL color bar. 100%

White.

White (75%) signal

White (100%) signal

0.7V

Burst Signal

(as fiat as possible)

0.3V

0.3V

Horizontal sync signal

Fig. 4-5 Color bar signal of pattern generator

White (100%)

White (75%)

1V

0.7V

0.3V

Horizontal sync signal

Color bar signal waveform

Burst

0.3V

Fig. 4-4 Alignment Tape

White

100%

Black

Color bar pattern

Fig. 4-6 Color bar signal of alignment tape (75% Color Bars)



4-5-3 PROGRAM SW

SW

POSITION

I a II b III c IV d V e VI f VII

SW A

SW B

SW C

S/SEN

ON

OFF

OFF

ON

E/SEN

POSITION

STANBY

POWER OFF

LOADING START

LOADING END

REV

PLAY

STOP1

STOP 2

FF / REW 1

FF / REW 2

POWER

OFF

STANDBY

LOAD

END

REV PLAY

LOAD

START

FL SW : ON-less than 3.5v / OFF-more than 3.5v (Input to A/D port)

START / END SENSOR : ON-"L", OFF-"H" : DON'T CARE

SPT1 SPT2 F/R1 F/R2

0

0

1

0

1

0

0

0

1

A

0

PROGRAM S/W

B

0

C

0

0

0

0 ->1

0

0

1

1

1

0

0

0

1

0

1

0

0

1

1

TAPE SEN

X

X

1

1

S

0

1

1

X

X

X

X

X

X

F

0

X

X

X

X

X

X

Eject

OPERATION MODE

Unload POWER OFF

(Tape loading start point)

(Tape loading end point)

Reverse Picture Ssarch, Reverse SLOW

Play, Rec,F-PS,Still,SLOW,F-ADV

Stop (Play position 5 Min. over)

(MAIN Break ON MODE)

High speed Rew, Low speed FF

High speed FF, Low speed Rew

X : DON’T CARE


MEMO


Troubleshooting

5. Troubleshooting

5-1 No Power (No Picture on)

No

Check both terminal voltages of

C805 (280~300V).

Yes

No

Check D801S~804S

FD801S

Is IC801S Pin 3

19~22V?

Yes

Check/Replace

T801S

No

Check IC801S

/Zener diode

Check both terminal voltages of C813 (125V)

Yes

No

Check

Voltage of A5V,A3.3V,

A15V power line.

Check whether each power line is short or open.

No

Yes

Is IC201S

Pin 54 Voltage 3.3V?

No

Yes

Check

H.V SYNC on

IC201S Pins 33, 21, 22

Check/Replace

IC901.

No

Yes

Check

IC201S Pin 11 is High when power is On.

Check/Replace

IC902.

Yes

Check the voltage of TU001.


Troubleshooting

5-2 No RF Picture / Sound

Check

IC201S #40, #24

Yes

Yes

Check

IC201S R, G, B, pins 51, 52, 53

No

No

Check Another I 2 C bus line

Replace IC201S

Yes

Check Q401, Q402

No

Replace

Yes

Check FBT

No

Replace

No

Check After bus line open


5-3 No Picture (Sound OK)

1 Check the Brightness, Contrast and Color adjustments

2. Check: AV Picture, Video Playback

3. See Video Block Diagram

5-4 No Sound (Picture OK)

1. Check the Volume adjustment level.

2. Check AV Video, Sound Playback

3. See Audio Block Diagram

5-5 RF Weak Signal (Playback, AV Mode OK)

1. Check Tuner (TU01S) B+. Check : 9V, 33V, 5V (CN802A)

5-6 Recording Defect

1. CN802A Check : Retouch

2. 2nd Tuner (TU02S) B+. Check : 33V(LT02)

5V (JTV501)

3. 2nd If : Check 5V (ICT01), Video out, Audio out

4. Video Defect : IC701 Check

5. Audio Defect : IC701 Check

6. Standby Recording Defect, ICM601 #42 Line:

7. VPS (PDC) Recording Defect: Check ICP01, #5, #27, #24, #2

Samsung Electronics

Troubleshooting

5-3

Troubleshooting

5-7 No Color

1. Check the Color Adjustment level

2. Check the Sandcastle Pulse Line : IC201S #34

3. Check the R-Y, B-Y Line : IC201S #51~#53

5-8 No Vertical SCAN

1. Check L301, L302, C310

2. Check IC301, #2

3. Check IC201S #21, #22

4. Check DY Connector

5-9 Horizontal Size

1. Check LR401S, L402, CR402S


5-10 Play Mode Inoperative

RF-VIDEO

Yes

Insert a Cassette

Tape Recorded by

Another VCR and

Press Play Button

Yes

Play

Indication in

Display

Yes

No

No

Mechanism

Operation

No

Yes

Does Not Operate or

Operates but Stops Soon

No

PB-Video

Yes

See (PB Audio)

Audio Missing in

Play Mode

See Video Missing

In RF Mode

See

(Regulator Inoperative)

See

(Mechanism Does Not

Operate in Play Mode)

See

Video Missing in

Play Mode

Troubleshooting


Troubleshooting

5-11 Mechanism Does Not Operate In Play Mode

Mechanism Does Not

Operate In Play Mode

Place VCR

Power On

5-6

Capstan

Rotation

Yes

S, T Reel

ICM601-99,98

Yes

Prog, SW State

ICM601-63,64,65

Yes

Replace ICM601

Load a Tape and

Press Play Button

Yes

Tape Loading

Operation

No

(Load)

ICM601-38 : HIGH

ICM601-39 : LOW

No

Yes or VCR Stops Soon

Replace ICM601

(S.End Sensor)

ICM601-77,76

High

Low

Cylinder

Rotation

OK but VCR Stops Soon

No

(SW 25Hz)

ICM601-24

Yes

No

Check Tape

See

(Cylinder Does

Not Rotate)

Check CYL FG.

ICM601-93

Moter B+

ICM602-3, 9, 21

Replace ICM602

No

See

(Capstan Does

Not Rotate)

DC

No

PTM601, PTM602,

Supply/Take Up Reel Sensor

PTM601, PTM602

Deck Loading Motor

Mechanism

No

Motor B+ Line

Samsung Electronics

5-12 Record Mode Inoperative

Play

Operation

Yes

Load VCR With a Blank

Tape and Press Record Button

Yes

Tape Eject

No

No

Rec SW Logic

ICM601

See (Play Mode

Inoperative)

No

Change Tape Replace

Yes

Replace SWM611

Low

Check ICM601

D/ REC (H)

ICM601-66

High

No

See

(Video Missing in

Record Mode)

REC-Video

Yes

See (Audio Mising in

Record Mode)

Troubleshooting


Troubleshooting

5-13 Fast Forward Mode Inoperative

Load VCR With a Tape and Press F.Fwd Button

Yes

Mechanism

State ICM601-63,

64,65

(F.FWD)

Capstan Motor

Rotation

(Rotate)

Check Mechanism

(STOP)

(STOP)

See

(Mechanism Does Not

Operate In Play Mode)

See

(Capstan Does

Not Rotate)


5-14 Rewind Mode Inoperative

Load VCR With a Tape

(Rotate)

Press Rewind Button

Yes

Mechanism

State ICM601-63,

64,65

(Rew)

Capstan Motor

Rotation

(Rotate)

Check Mechanism

No

(STOP)

(STOP)

See (Fast Forward Mode

Inoperative)

See

(Mechanism Does Not

Operate In Play Mode)

See ICM601-25

Troubleshooting


Troubleshooting

5-15 Rev Search Mode Inoperative

Play

Operation

Yes

No See Play Mode

Inoperative

Press REV Search Button

Yes

Capstan Speed

Play Speed

Check Mechanism

Serach Speed

Noise Bar Locking

Yes

No

Rec SW Logic

ICM601

Yes

Replace ICM601 Capstan Motor

No

Replace ICM601

Change Tape Replace


5-16 Cassette Loading Mechanism Does Not Operate

Turn the VCR Power

On and Insert a Tape

Tape Loading

Yes

Press Eject Button

No

Check ICM601

No

Check

(Control Pulse)

ICM601-76,77

Yes

ICM601 - 39

Yes

ICM602-12:LOW

ICM602-11:HIGH

No

No

No

Check Start/End

Sensor ICM601

Check

LM B+ Line

Replace

ICM602

Troubleshooting


Troubleshooting

5-17 No Servo Lock

Play

C-FG

ICM601-93

Yes

No

CTL Pluse

ICM601-4

Yes

Check CTL

Pulse AC Level (SP, LP

: Over 2Vp-p)

Yes

Replace

ICM601

No

No

Check Start/End

Sensor ICM601

Check

A/C Head


5-18 Capstan Does Not Rotate

9V

CNM603-5

Yes

AL 5V

CNM603-8

Yes

Place the VCR

In Play Mode

Yes

CNM603-3 2.5V

Yes

2.5V

CNM603-4

Yes

Check

Capstan Motor

No

No

No

No

Check 12V at AL15V Line of

Power Supply

Check A5V at AL6V

Line of Power Supply

Check I-LIMIT.

RM618

Check C.M CTL/

RM606, RM604

No Check

ICM601

Troubleshooting


Troubleshooting

5-19 Drum Does Not Rotate

Check 12V

ICM602-9,21

Yes

Place the VCR

In Play Mode

Yes

No

Check 12V

CYL-Speed

Slower

(8 MHz)

XTM601

Yes

Check

Cylinder Motor

Faster Check D-FG,D-PG

ICM601-96,97Square Wave

No Replace

XTM601, CM609, CM610


5-20 Video Missing In Play Mode

Video EE Mode

Operation

Yes

Place VCR

Play Mode

Yes

Video FM In

ICM301-17

Yes

Video

ICM301-20

Yes

No

No

See (Video Missing

In EE Mode)

Check ICM301-18

No

Check

QM302

No

No Video

ICM301-29

Yes

Check Video Out Line

Replace ICM301

Check

Video Head

Troubleshooting


Troubleshooting

5-21 Video Missing In Record Mode

Video EE Mode

Operation

Yes

Place VCR

Record Mode

Yes

FM-Video

ICM301-21

Yes

FM-Video

ICM301-18

Yes

No

No

No

TV Switching

Circuit Check

Replace ICM301

Check RM313

Check Video Head


5-22 Color Missing In Play Mode

FM-ENV

ICM301-61

Yes

Color

ICM301-71

No

See (Video Missing

In Play Mode)

Yes

No

S/W 25Hz

ICM301-11

Yes

Check

XTM301 : 4.43MHz

Yes

No

No

Replace ICM301

Check

ICM601

Change XTM301

No

Troubleshooting


Troubleshooting

5-23 Color Missing In Record Mode

(VIdeo In)

Record Mode

Yes

Color

ICM301-61

No

Yes

TV Switching

Circuit Check

No Check

XTM301 : 4.43MHz

Yes

No

Replace XTM301

Replace ICM301

FM Signal

ICM301-71

Yes

Replace ICM301

No

Check CM351


5-24 Audio Signal Missing in Play Mode (MONO MODE)

Check ICM301 pin75 : 5V

Yes

Check

ICM301 pin23,24

(IC CLK DATA)

Yes

Check ICM301 pin 1 : PB Audio Signal

(Small Signal)

Yes

Check ICM301

pin100 : PB audio signal

(Small Signal)

Yes

Check ICM301

pin96 : PB Audio

Signal

Yes

Check

TV NICAM PART(Sound Block)

No

No

No

No

No

Check PC 5V Line

Check VCR MICOM

(ICM601- pin27, 28)

Check A/C Head and PB EQ

Block (AUDIO HEAD AZIMUTH)

Check CM301

Replace ICM301

Troubleshooting


Troubleshooting

5-25 Audio Signal Missing After Recording (MONO MODE)

Check

IC702 #14

MONO out

Yes

Place VCR in REC Mode

Yes

Check

ICM301 pin 75:

5V

Yes

Check

ICM301 pin7 REC audio signal

Yes

Check

FLM501 Pin5 REC bias signal

Yes

Check

CNM302 , Pin5

Yes

Replace CNM302

No

No

No

No

No

Check IC702

Check PC 5V Line

Replace ICM301

Check CM370, RM357, RM358

CM371, CM373, CM372,

QM312, RM359

Check A/C

Head Assembly


Electrical Parts List

You can search for the updated part code through ITSELF web site.

URL : http://itself.sec.samsung.co.kr

7. Electrical Parts List

7-1 TW20P14X/BWT

Loc. No.

Code No. Description ; Specification Remark Loc. No.

ASSY CHASSIS

1 AA91-05353C ASSY CHASSIS TW20P14X/BWT,C17A,RUSS,SEB&

3

3

3

2

3

3

AA94-11841A ASSY PCB MISC-M/DECK TF20P1D4X/XEF,C17A

0201-000280 ADHESIVE-TS

0202-000008 SOLDER-WIRE

EH-260D,RED,450°æ50PS,10CC

S63S-W3.0,S63S,D3,63Sn/37Pb,

0202-000187 SOLDER-WIRE FLUX -,RS60S,D1.2,63Sn/37Pb

0204-000442 SOLVENT 1M-1000,C3H70H,96,-

0204-001024 FLUX DF-98TVS,-,20%,-

3 PTM601 0604-001122 PHOTO-INTERRUPTER

3 PTM602 0604-001122 PHOTO-INTERRUPTER

TR,0.065%,150mW,DIP-4,

TR,0.065%,150mW,DIP-4,

3 ICM602 1003-001318 IC-MOTOR DRIVER LB11880,DIP,30P,417MIL,-

3 IC601 1201-001386 IC-POWER AMP 7267,DIP,16P,-,DUAL,32dB,PL

3 XTM301 2801-000277 CRYSTAL-UNIT 4.433619MHz,8ppm,28-AAM,S,1

3 CNM301 3708-000394 CONNECTOR-FPC/FFC/PIC 6P,1.25mm,STRAIGHT



3 CNM303 3710-001648 CONNECTOR-SOCKET 2P,1R,2.5mm,STRAIGHT,SN

3 CN601B 3711-002642 CONNECTOR-HEADER BOX,3P,1R,2.5mm,STRAIGH

3 CN601A 3711-002643 CONNECTOR-HEADER


3 TPCN01 3711-002648 CONNECTOR-HEADER

3 CNM603 3711-003749 CONNECTOR-HEADER

3 LDM602 3722-001742 JACK-PIN

BOX,4P,1R,2.5mm,STRAIGH



BOX,8P,2R,2mm,STRAIGHT,

2P,-,NI,YEL/WHT,-

3 CNM302 3809-001206 CABLE-FLAT

3 CNM602 3809-001312 CABLE-FLAT

3 FLM301 AA26-10006C TRANS RF

3 SWM610 AA34-20001A SWITCH-MODE

3 SWM611 AA34-40001A SWITCH-REC.

30V,-20to+80C,140mm,6P,1.25mm

30V,80C,110MM,7P,1.25MM,UL289

-,7MF,BIAS,2.4MH,7MM,-,65.3KHZ

1,25x14.6x29.8mm,BK,DC5V

1EA,37.5x14.4mm,BK,DC5V

3 W01 AA39-00046C LEAD CONNECTOR-ASSY ,1P,100MM,JUMPER,BLK

3 CN802A AA39-00180C LEAD CONNECTOR-ASSY TF20P1,UL1007#26,UL/

3 CN801A AA39-20055B LEAD CONNECTOR-ASSY ,6P,300,YBNH025-06,6

3 CNM601 AA39-20603A LEAD CONNECTOR-ASSY ,2P,100MM,GIL-S-2S-S

3 REM601 AA59-60003V MODULE REMOCON -,SRV-18,38KHZ,940NM,MESH

3 GPM01 AA63-00444B GROUND TVCR,PBS,T0.3,-,-,-,SUS-DECK

3 LDM601 AA91-60318A ASSY HOLDER-LED BLK,IR LED,HB,ABS,TS-DEC

4 LED 0601-001303 LED-IR

4 HOLDER AA61-00003A HOLDER-LED

SIDE-VIEW,2.5mm,75mW,6V,950nm,

TVN-502V,ABS,-,-,-,BLK,HB

3 SM601 AA91-60319A ASSY HOLDER-SENSOR BLK,TR LED,HB,ABS,TS-

3 SM602 AA91-60319A ASSY HOLDER-SENSOR BLK,TR LED,HB,ABS,TS-

4 TR 0603-001011 PHOTO TR NPN,35V,6V,50mA,75mW,BK

4 HOLDER AA61-00005A HOLDER-SENSOR TVN-502V,ABS,-,-,-,BLK,HB

3 AA97-12679A ASSY ROBOT CS21K5

4 IC702 0801-000213 IC-CMOS LOGIC 4052,MULTIPLEXER,DIP,16P,3

4 IC701 0801-000961 IC-CMOS LOGIC

4 IC902 1103-001177 IC-EEPROM

4 SF101S 2904-000267 FILTER-SAW AV

4 JS701 3722-000183 JACK-SCART

4 IC201S AA09-00315A IC MICOM

4053,MUTIPLEXER,DIP,16P,30

24WC16,2048x8Bit,DIP,8P,-,-,2.

38.9MHz,SIP5P,ST,16.8dB,PA

21P,4mm,SN,BLK,NO

TDA9381PS/N2/3I0845,SPM-44WOT

4 TU01S HA83-00061A LA-TUNER

4 AA97-12960A ASSY AUTO

AA40-00076A

,C17A

5 DM301 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,




5 DJ01 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,

5 D201

5 D202

5 D205

0401-000005

0401-000005

0401-000005

DIODE-SWITCHING 1N4148,100V,200mA,DO-35,



5 D601

5 D602

0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,

0402-000132 DIODE-RECTIFIER 1N4004,400V,1A,DO-41,TP

5 D203 0402-000132 DIODE-RECTIFIER 1N4004,400V,1A,DO-41,TP

5 ZDM601 0403-000508 DIODE-ZENER MTZJ5.6B,5.6V,5.45-5.73V,500

Code No. Description ; Specification Remark

5 DZ903 0403-000508 DIODE-ZENER

5 DZ902 0403-000508 DIODE-ZENER

5 DZ901 0403-000508 DIODE-ZENER

5 DZ101 0403-000508 DIODE-ZENER

5 DZ206 0403-000720 DIODE-ZENER

5 DZ701 0403-000720 DIODE-ZENER

5 ZDM602 0403-000720 DIODE-ZENER

5 DZ201 0403-000720 DIODE-ZENER

5 DZ203 0403-000720 DIODE-ZENER

5 DZ204 0403-000720 DIODE-ZENER

MTZJ5.6B,5.6V,5.45-5.73V,500

MTZJ5.6B,5.6V,5.45-5.73V,500

MTZJ5.6B,5.6V,5.45-5.73V,500

MTZJ5.6B,5.6V,5.45-5.73V,500

MTZJ9.1B,9.1V,8.57-9.01V,500

MTZJ9.1B,9.1V,8.57-9.01V,500

MTZJ9.1B,9.1V,8.57-9.01V,500

MTZJ9.1B,9.1V,8.57-9.01V,500

MTZJ9.1B,9.1V,8.57-9.01V,500

MTZJ9.1B,9.1V,8.57-9.01V,500

5 DZ205 0403-000720 DIODE-ZENER

5 KEZI 0403-000720 DIODE-ZENER

MTZJ9.1B,9.1V,8.57-9.01V,500

MTZJ9.1B,9.1V,8.57-9.01V,500

5 DZ202 0403-001322 DIODE-ZENER MTZJ8.2B,7.78-8.19V,500mW,DO

5 QM312 0501-000010 TR-SMALL SIGNAL KSC1008,NPN,800mW,TO-92,

5 Q701 0501-000283 TR-SMALL SIGNAL KSA539,PNP,400mW,TO-92,T

5 Q201 0501-000283 TR-SMALL SIGNAL KSA539,PNP,400mW,TO-92,T

5 QM315 0501-000303 TR-SMALL SIGNAL KSA733,PNP,250mW,TO-92,T



5 QM317 0501-000389 TR-SMALL SIGNAL KSC815,NPN,400mW,TO-92,T


5 Q205 0501-000389 TR-SMALL SIGNAL KSC815,NPN,400mW,TO-92,T

5 Q202

5 Q203

5 Q204

0501-000389

0501-000389

0501-000389

TR-SMALL SIGNAL KSC815,NPN,400mW,TO-92,T










5 QM314 0501-000442 TR-SMALL SIGNAL KTC3203-Y,NPN,400mW,T0-9

5 QM313 0501-000442 TR-SMALL SIGNAL KTC3203-Y,NPN,400mW,T0-9

5 QM303 0504-000119 TR-DIGITAL KSR1004,NPN,300MW,47K/47K,TO-

5 Q601 0504-000123 TR-DIGITAL

5 ICM603 1203-000642 IC-RESET

5 RM638 2001-000003 R-CARBON

5 RM633 2001-000003 R-CARBON

5 RM632 2001-000003 R-CARBON

KSR1010,NPN,300mW,10K,TO-92,T

572,TO-92,3P,-,PLASTIC,2.35/2.

330ohm,5%,1/8W,AA,TP,1.8x3.2mm

330ohm,5%,1/8W,AA,TP,1.8x3.2mm

330ohm,5%,1/8W,AA,TP,1.8x3.2mm

5 RM319 2001-000003 R-CARBON

5 RM318 2001-000003 R-CARBON

5 RM655 2001-000005 R-CARBON

5 RM654 2001-000005 R-CARBON

5 R205 2001-000005 R-CARBON

5 RM352 2001-000006 R-CARBON

5 R212 2001-000008 R-CARBON

5 RM370 2001-000008 R-CARBON

5 RM612 2001-000009 R-CARBON

5 RM644 2001-000010 R-CARBON

5 RM610 2001-000010 R-CARBON

5 R203 2001-000011 R-CARBON

5 R711 2001-000037 R-CARBON(S)

5 RM641 2001-000118 R-CARBON(S)

5 RM349 2001-000221 R-CARBON

5 RM316 2001-000221 R-CARBON

5 RM335 2001-000232 R-CARBON

5 RM323 2001-000241 R-CARBON

5 RM307 2001-000241 R-CARBON

5 RM339 2001-000258 R-CARBON

5 RM358 2001-000258 R-CARBON

5 RM623 2001-000273 R-CARBON

5 R917

5 R916

5 R915

2001-000281

2001-000281

2001-000281

R-CARBON

R-CARBON

R-CARBON

330ohm,5%,1/8W,AA,TP,1.8x3.2mm

330ohm,5%,1/8W,AA,TP,1.8x3.2mm

390ohm,5%,1/8W,AA,TP,1.8x3.2mm

390ohm,5%,1/8W,AA,TP,1.8x3.2mm

390ohm,5%,1/8W,AA,TP,1.8x3.2mm

2.4KOHM,5%,1/8W,AA,TP,1.8X3.2M

15KOHM,5%,1/8W,AA,TP,1.8X3.2MM






330OHM,5%,1/2W,AA,TP,2.4X6.4

180OHM,5%,1/2W,AA,TP,2.4X6.4

1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M

1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M

1.3KOHM,5%,1/8W,AA,TP,1.8X3.2M

1.5KOHM,5%,1/8W,AA,TP,1.8X3.2M

1.5KOHM,5%,1/8W,AA,TP,1.8X3.2M

1.8KOHM,5%,1/8W,AA,TP,1.8X3.2M

1.8KOHM,5%,1/8W,AA,TP,1.8X3.2M

100KOHM,5%,1/8W,AA,TP,1.8X3.2M

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM



Loc. No.


5 R502

5 R501

5 R216

5 R209

5 R208

5 R908

5 R906

5 R905

5 R712

5 R901

5 R911

5 R910

2001-000281 R-CARBON

2001-000281 R-CARBON

5 R909 2001-000281 R-CARBON

5 RM668 2001-000281 R-CARBON

5 RM667 2001-000281 R-CARBON

5 RM666 2001-000281 R-CARBON

5 RM665 2001-000281 R-CARBON

5 RM664 2001-000281 R-CARBON

5 RM663 2001-000281 R-CARBON

5 R503 2001-000281 R-CARBON

2001-000281

2001-000281

2001-000281

2001-000281

2001-000281

R-CARBON

R-CARBON

R-CARBON

R-CARBON

R-CARBON

2001-000281 R-CARBON

2001-000281 R-CARBON

2001-000281 R-CARBON

2001-000281 R-CARBON

2001-000281 R-CARBON

5 R902 2001-000281 R-CARBON

5 RM639 2001-000290 R-CARBON

5 RM637 2001-000290 R-CARBON

5 RM620 2001-000290 R-CARBON

5 RM619 2001-000290 R-CARBON

5 RM615 2001-000290 R-CARBON

5 RM614 2001-000290 R-CARBON

5 RM697 2001-000290 R-CARBON

5 RM696 2001-000290 R-CARBON

5 RM693 2001-000290 R-CARBON

5 RM692 2001-000290 R-CARBON

5 RM670 2001-000290 R-CARBON

5 RM656 2001-000290 R-CARBON

5 R718 2001-000290 R-CARBON

5 R710 2001-000290 R-CARBON

5 R709

5 R707

5 R601

5 R504

2001-000290

2001-000290

2001-000290

2001-000290

R-CARBON

R-CARBON

R-CARBON

R-CARBON

5 RM360 2001-000290 R-CARBON

5 R923

5 R922

5 R907

5 R920

5 R921

2001-000290 R-CARBON

2001-000290 R-CARBON

2001-000290 R-CARBON

2001-000290 R-CARBON

2001-000290 R-CARBON

5 RM606 2001-000319 R-CARBON

5 RM671 2001-000331 R-CARBON

5 RM303 2001-000331 R-CARBON

5 R604 2001-000347 R-CARBON

5 RM305 2001-000362 R-CARBON

5 RM356 2001-000405 R-CARBON

5 R218 2001-000405 R-CARBON

5 RM657 2001-000429 R-CARBON

5 RM674 2001-000429 R-CARBON

5 RM678 2001-000429 R-CARBON

5 RM679 2001-000429 R-CARBON

5 RM653 2001-000429 R-CARBON

5 RM651 2001-000429 R-CARBON

5 RM650 2001-000429 R-CARBON

5 RM649 2001-000429 R-CARBON

5 RM648 2001-000429 R-CARBON

5 RM682 2001-000429 R-CARBON

5 RM694 2001-000429 R-CARBON

5 RM690 2001-000429 R-CARBON

5 RM689 2001-000429 R-CARBON

5 RM688 2001-000429 R-CARBON

5 RM687 2001-000429 R-CARBON

5 RM686 2001-000429 R-CARBON

5 RM685 2001-000429 R-CARBON

5 RM684 2001-000429 R-CARBON

5 RM683 2001-000429 R-CARBON

5 RM647 2001-000429 R-CARBON

5 RM605 2001-000429 R-CARBON

5 RM362 2001-000429 R-CARBON

5 RM361 2001-000429 R-CARBON

5 RM341 2001-000429 R-CARBON

5 RM333 2001-000429 R-CARBON

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

























120KOHM,5%,1/8W,AA,TP,1.8X3.2M




150OHM,5%,1/8W,AA,TP,1.8X3.2MM

180OHM,5%,1/8W,AA,TP,1.8X3.2MM

180OHM,5%,1/8W,AA,TP,1.8X3.2MM



























5 RM317 2001-000429 R-CARBON

5 RM312 2001-000429 R-CARBON

5 RM310 2001-000429 R-CARBON

5 R903 2001-000429 R-CARBON

5 RM609 2001-000429 R-CARBON

5 RM643 2001-000429 R-CARBON

5 RM629 2001-000429 R-CARBON

5 RM628 2001-000429 R-CARBON

5 RM626 2001-000429 R-CARBON

5 RM625 2001-000429 R-CARBON

5 RM613 2001-000429 R-CARBON

5 RM621 2001-000429 R-CARBON

5 RM622 2001-000429 R-CARBON

5 RM624 2001-000429 R-CARBON

5 R721 2001-000429 R-CARBON

5 RM340 2001-000449 R-CARBON

5 R913 2001-000449 R-CARBON

5 R912 2001-000449 R-CARBON

5 RM344 2001-000454 R-CARBON

5 RM359 2001-000458 R-CARBON

5 RM346 2001-000472 R-CARBON

5 RM334 2001-000472 R-CARBON

5 RM313 2001-000472 R-CARBON

5 R210 2001-000490 R-CARBON

5 R211 2001-000490 R-CARBON

5 RM372 2001-000515 R-CARBON

5 RM326 2001-000515 R-CARBON

5 RM315 2001-000515 R-CARBON

5 RM660 2001-000522 R-CARBON

5 RM642 2001-000522 R-CARBON

5 RM602 2001-000522 R-CARBON

5 RM363 2001-000522 R-CARBON

5 RM354 2001-000522 R-CARBON

5 R706 2001-000522 R-CARBON

5 R722 2001-000527 R-CARBON

5 R227 2001-000531 R-CARBON

5 RM669 2001-000539 R-CARBON

5 RM661 2001-000554 R-CARBON

5 RM601 2001-000554 R-CARBON

5 RM320 2001-000554 R-CARBON

5 R605

5 R204

2001-000563 R-CARBON

2001-000563 R-CARBON

5 R206 2001-000591 R-CARBON

5 RM675 2001-000613 R-CARBON

5 R214 2001-000613 R-CARBON

5 RM640 2001-000633 R-CARBON

5 R719 2001-000633 R-CARBON

5 RM304 2001-000645 R-CARBON

5 RM616 2001-000660 R-CARBON

5 RM604 2001-000660 R-CARBON

5 RM306 2001-000660 R-CARBON

5 R704 2001-000660 R-CARBON

5 R201 2001-000689 R-CARBON

5 RM331 2001-000723 R-CARBON

5 RM636 2001-000734 R-CARBON

5 RM635 2001-000734 R-CARBON

5 RM634 2001-000734 R-CARBON

5 RM365 2001-000734 R-CARBON

5 RM345 2001-000734 R-CARBON

5 R221 2001-000734 R-CARBON

5 R914

5 R919

2001-000734 R-CARBON

2001-000734 R-CARBON

5 RM324 2001-000734 R-CARBON

5 R220 2001-000739 R-CARBON

5 R219 2001-000739 R-CARBON

5 RM379 2001-000766 R-CARBON

5 RM328 2001-000766 R-CARBON

5 RM357 2001-000780 R-CARBON

5 RM327 2001-000780 R-CARBON

5 RM618 2001-000786 R-CARBON

5 RM377 2001-000786 R-CARBON

5 RM375 2001-000786 R-CARBON

5 R226

5 R223

5 R106

2001-000786

2001-000786

2001-000786

R-CARBON

R-CARBON

R-CARBON

5 R207 2001-000793 R-CARBON

5 RM369 2001-000800 R-CARBON
















2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M

2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M

2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M

2.2MOHM,5%,1/8W,AA,TP,1.8X3.2M

2.2OHM,5%,1/8W,AA,TP,1.8X3.2MM

2.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

2.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

2.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

200OHM,5%,1/8W,AA,TP,1.8X3.2MM

200OHM,5%,1/8W,AA,TP,1.8X3.2MM

220OHM,5%,1/8W,AA,TP,1.8X3.2MM

220OHM,5%,1/8W,AA,TP,1.8X3.2MM

220OHM,5%,1/8W,AA,TP,1.8X3.2MM







22OHM,5%,1/8W,AA,TP,1.8X3.2MM

240KOHM,5%,1/8W,AA,TP,1.8X3.2M


270OHM,5%,1/8W,AA,TP,1.8X3.2MM

270OHM,5%,1/8W,AA,TP,1.8X3.2MM

270OHM,5%,1/8W,AA,TP,1.8X3.2MM



3.3KOHM,5%,1/8W,AA,TP,1.8X3.2M

3.9KOHM,5%,1/8W,AA,TP,1.8X3.2M

3.9KOHM,5%,1/8W,AA,TP,1.8X3.2M



330KOHM,5%,1/8W,AA,TP,1.8X3.2M





390KOHM,5%,1/8W,AA,TP,1.8X3.2M

4.3KOHM,5%,1/8W,AA,TP,1.8X3.2M

4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

4.7MOHM,5%,1/8W,AA,TP,1.8X3.2M

4.7MOHM,5%,1/8W,AA,TP,1.8X3.2M



470OHM,5%,1/8W,AA,TP,1.8X3.2MM

470OHM,5%,1/8W,AA,TP,1.8X3.2MM







47OHM,5%,1/8W,AA,TP,1.8X3.2MM

5.1KOHM,5%,1/8W,AA,TP,1.8X3.2M



Loc. No.


5 RM373 2001-000812 R-CARBON

5 RM351 2001-000812 R-CARBON

5 RM302 2001-000812 R-CARBON

5 R703 2001-000812 R-CARBON

5 R702 2001-000812 R-CARBON

5 RM611 2001-000832 R-CARBON

5 RM348 2001-000832 R-CARBON

5 RM347 2001-000832 R-CARBON

5 RM627 2001-000850 R-CARBON

5 R202 2001-000857 R-CARBON

5 RM607 2001-000864 R-CARBON

5 RM353 2001-000904 R-CARBON

5 RM314 2001-000924 R-CARBON

5 R225 2001-000924 R-CARBON

5 R107 2001-000924 R-CARBON

5 RM380 2001-000947 R-CARBON

5 RM350 2001-000947 R-CARBON

5 RM329 2001-000947 R-CARBON

5 R215 2001-000947 R-CARBON

5 R105 2001-000947 R-CARBON

5.6KOHM,5%,1/8W,AA,TP,1.8X3.2M

5.6KOHM,5%,1/8W,AA,TP,1.8X3.2M

5.6KOHM,5%,1/8W,AA,TP,1.8X3.2M

5.6KOHM,5%,1/8W,AA,TP,1.8X3.2M

5.6KOHM,5%,1/8W,AA,TP,1.8X3.2M

510OHM,5%,1/8W,AA,TP,1.8X3.2MM

510OHM,5%,1/8W,AA,TP,1.8X3.2MM

510OHM,5%,1/8W,AA,TP,1.8X3.2MM

560KOHM,5%,1/8W,AA,TP,1.8X3.2M

560OHM,5%,1/8W,AA,TP,1.8X3.2MM


620OHM,5%,1/8W,AA,TP,1.8X3.2MM

680OHM,5%,1/8W,AA,TP,1.8X3.2MM

680OHM,5%,1/8W,AA,TP,1.8X3.2MM

680OHM,5%,1/8W,AA,TP,1.8X3.2MM

7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M

7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M

7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M

7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M

7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M

5 RJ702 2001-000958 R-CARBON

5 RJ701 2001-000958 R-CARBON

5 R714

5 R715

5 R716

2001-000969

2001-000969

2001-000969

R-CARBON

R-CARBON

R-CARBON

5 R717

5 R720

5 R222

5 R701

5 R705

2001-000969

2001-000969

2001-000969

2001-000969

2001-000969

R-CARBON

R-CARBON

R-CARBON

R-CARBON

R-CARBON

750OHM,5%,1/8W,AA,TP,1.8X3.2MM

750OHM,5%,1/8W,AA,TP,1.8X3.2MM

75OHM,5%,1/8W,AA,TP,1.8X3.2MM

75OHM,5%,1/8W,AA,TP,1.8X3.2MM

75OHM,5%,1/8W,AA,TP,1.8X3.2MM

75OHM,5%,1/8W,AA,TP,1.8X3.2MM

75OHM,5%,1/8W,AA,TP,1.8X3.2MM

75OHM,5%,1/8W,AA,TP,1.8X3.2MM

75OHM,5%,1/8W,AA,TP,1.8X3.2MM

75OHM,5%,1/8W,AA,TP,1.8X3.2MM

5 R708

5 R713

2001-000969 R-CARBON

2001-000969 R-CARBON

5 RM338 2001-000977 R-CARBON

5 RM378 2001-000995 R-CARBON

5 RM371 2001-001000 R-CARBON

75OHM,5%,1/8W,AA,TP,1.8X3.2MM

75OHM,5%,1/8W,AA,TP,1.8X3.2MM

8.2KOHM,5%,1/8W,AA,TP,1.8X3.2M

820OHM,5%,1/8W,AA,TP,1.8X3.2MM


5 R224

5 R213

2001-001026 R-CARBON

2004-001914 R-METAL

910OHM,5%,1/8W,AA,TP,1.8X3.2MM

39Kohm,2%,1/8W,AA,TP,1.8x3.5mm

5 RM630 2008-000253 R-FUSIBLE(S) 0.47ohm,5%,1W,AF,TP,3.9x10m

5 CM319 2201-000345 C-CERAMIC,DISC 0.2NF,5%,50V,SL,TP,7X3MM,

5 C226 2201-000472 C-CERAMIC,DISC 0.33NF,5%,50V,SL,TP,8.5X3

5 CM316 2201-000499 C-CERAMIC,DISC 0.39NF,5%,50V,SL,TP,8.5X3

5 C905 2201-000573 C-CERAMIC,DISC 0.047NF,5%,50V,C0G,TP,5X3

5 C906 2201-000573 C-CERAMIC,DISC 0.047NF,5%,50V,C0G,TP,5X3

5 CM360 2201-000611 C-CERAMIC,DISC 0.056NF,5%,50V,C0G,TP,7X3

5 CM359 2201-000611 C-CERAMIC,DISC 0.056NF,5%,50V,C0G,TP,7X3

5 CM315 2201-002031 C-CERAMIC,DISC 0.005NF,0.5PF,50V,C0G,TP,

5 CM640 2202-000121 C-CERAMIC,MLC-AXIAL 100pF,10%,50V,Y5P,TP

5 CJ702 2202-000121 C-CERAMIC,MLC-AXIAL 100pF,10%,50V,Y5P,TP

5 CM613 2202-000127 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,25V,Y5V







5 CT19 2202-000127 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,25V,Y5V









5 C602 2202-000127 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,25V,Y5V

5 C106

5 C102

2202-000127 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,25V,Y5V

2202-000127 C-CERAMIC,MLC-AXIAL 10nF,+80-20%,25V,Y5V








5 CM318 2202-000162 C-CERAMIC,MLC-AXIAL 0.015NF,5%,50V,SL,TP

5 CM636 2202-000183 C-CERAMIC,MLC-AXIAL 2.2NF,20%,16V,Y5R,TP

5 CM637 2202-000183 C-CERAMIC,MLC-AXIAL 2.2NF,20%,16V,Y5R,TP


5 CM610 2202-000205 C-CERAMIC,MLC-AXIAL 22pF,5%,50V,SL,TP,1.


5 CM314 2202-000216 C-CERAMIC,MLC-AXIAL 0.027NF,5%,50V,SL,TP

5 C716 2202-000231 C-CERAMIC,MLC-AXIAL 0.33NF,10%,50V,Y5P,T

5 C715 2202-000231 C-CERAMIC,MLC-AXIAL 0.33NF,10%,50V,Y5P,T

5 C703

5 C731

2202-000231 C-CERAMIC,MLC-AXIAL 0.33NF,10%,50V,Y5P,T

2202-000243 C-CERAMIC,MLC-AXIAL 33pF,5%,50V,SL,TP,3.



5 CM606 2202-000632 C-CERAMIC,MLC-AXIAL 100nF,20%,50V,Z5U,TP












5 C231 2202-000632 C-CERAMIC,MLC-AXIAL 100nF,20%,50V,Z5U,TP

5 C205

5 C204

2202-000632

2202-000632

C-CERAMIC,MLC-AXIAL

C-CERAMIC,MLC-AXIAL

100nF,20%,50V,Z5U,TP

100nF,20%,50V,Z5U,TP






5 CM617 2202-000718 C-CERAMIC,MLC-AXIAL 3.9nF,20%,16V,Y5R,TP

5 CM616 2202-000718 C-CERAMIC,MLC-AXIAL 3.9nF,20%,16V,Y5R,TP

5 C704 2202-000719 C-CERAMIC,MLC-AXIAL 6.8nF,20%,16V,Y5R,TP

5 CM325 2202-000796 C-CERAMIC,MLC-AXIAL 1NF,10%,50V,Y5P,TP,3



5 C904

5 C224

2202-000796 C-CERAMIC,MLC-AXIAL 1NF,10%,50V,Y5P,TP,3

2202-000796 C-CERAMIC,MLC-AXIAL 1NF,10%,50V,Y5P,TP,3

5 C223 2202-000796 C-CERAMIC,MLC-AXIAL 1NF,10%,50V,Y5P,TP,3


5 0203-001123 TAPE-PAPER #53131,T0.15,W6.0,L200000,YEL








5 CM320 2202-000849 C-CERAMIC,MLC-AXIAL 0.018NF,5%,50V,C0G,T



5 CL08 2202-000632 C-CERAMIC,MLC-AXIAL 100nF,20%,50V,Z5U,TP




5 C227 2301-000104 C-FILM,PEF 1.2NF,5%,50V,TP,6.5X3.0X5.5MM

5 CM372 2301-000160 C-FILM,PEF

5 CM368 2301-000175 C-FILM,PEF

5 CM306 2301-000192 C-FILM,PEF

5 C201 2301-000204 C-FILM,PEF

5 C604 2301-000204 C-FILM,PEF

12nF,5%,50V,TP,11.0x6.0x9.0mm

15nF,5%,50V,TP,7.1x3.5x13mm,5

1nF,5%,50V,TP,5.3x10mm,5mm

2.7nF,5%,50V,TP,7.4x3.9x13mm,

2.7nF,5%,50V,TP,7.4x3.9x13mm,

5 C108 2301-000224 C-FILM,PEF

5 CM370 2301-000254 C-FILM,PEF

5 CM362 2301-000301 C-FILM,PEF

5 CM363 2301-000301 C-FILM,PEF

5 CM371 2301-000301 C-FILM,PEF

5 CM603 2301-000310 C-FILM,PEF

5 CM364 2301-000314 C-FILM,PEF

5 C217 2301-000342 C-FILM,PEF

5 CM305 2301-000342 C-FILM,PEF

5 CM303 2301-000383 C-FILM,PEF

5 C903

5 C232

2301-000383 C-FILM,PEF

2301-000445 C-FILM,PEF

5 CM660 2305-000289 C-FILM,MPEF

5 C712 2305-000289 C-FILM,MPEF

5 C216 2305-000289 C-FILM,MPEF

5 C215

5 C901

2305-000289 C-FILM,MPEF

2305-000412 C-FILM,MPEF

22nF,5%,50V,TP,7.4x3.9x13mm,5

39nF,5%,50V,TP,7.5x3.5x6.5mm,

6.8nF,5%,50V,TP,6.5X5.5X3.0X5

6.8nF,5%,50V,TP,6.5X5.5X3.0X5

6.8nF,5%,50V,TP,6.5X5.5X3.0X5

68nF,5%,50V,TP,8.0X8.5X4.0X5,

8.2nF,5%,50V,TP,6.5x3.0x5.5mm

2.2nF,5%,50V,TP,7.4x3.9x13mm,

2.2nF,5%,50V,TP,7.4x3.9x13mm,

10nF,5%,50V,TP,6x7x3.2mm,5mm

10nF,5%,50V,TP,6x7x3.2mm,5mm

4.7nF,5%,50V,TP,5.5x7x3mm,5mm

220nF,5%,63V,TP,-,5mm

220nF,5%,63V,TP,-,5mm

220nF,5%,63V,TP,-,5mm

220nF,5%,63V,TP,-,5mm

470nF,5%,63V,TP,-,5mm



Loc. No.


5 C207 2305-000412 C-FILM,MPEF

5 CM311 2305-000665 C-FILM,MPEF

5 C909

5 C230

5 C218

5 C210

5 C208

5 C225

5 C233

5 C104

5 C103

5 C206

5 C220

5 C234

5 C701

2305-000665

2305-000665

2305-000665

2305-000665

2305-000665

2309-000138

2401-002075

2401-000939

2401-000050

2401-000050

2401-000050

2401-000050

2401-000050

C-FILM,MPEF

C-FILM,MPEF

C-FILM,MPEF

C-FILM,MPEF

C-FILM,MPEF

C-FILM,PE-PPF

C-AL

C-AL

5 CM332 2401-000426 C-AL

5 CM323 2401-000426 C-AL

5 CM304 2401-000426 C-AL

5 CM361 2401-000590 C-AL

5 CM348 2401-000590 C-AL

5 CM333 2401-000590 C-AL

5 CM331 2401-000590 C-AL

5 CM317 2401-000590 C-AL

5 CM310 2401-000590 C-AL

5 C605 2401-000590 C-AL

5 CM611 2401-000598 C-AL

5 CM346 2401-000598 C-AL

5 CM344 2401-000598 C-AL

5 C219 2401-000603 C-AL

5 CM392 2401-000603 C-AL

5 C212

5 C221

2401-000649 C-AL

2401-000660 C-AL

5 CM308 2401-000665 C-AL

5 CM355 2401-000922 C-AL

5 CM324 2401-000922 C-AL

5 C606

5 C101

5 CT18

5 C601

2401-000922

2401-001101

2401-001101

2401-001115

C-AL

C-AL

C-AL

C-AL

5 CM307 2401-001250 C-AL

5 CM365 2401-001250 C-AL

5 CM639 2401-001250 C-AL

5 CM326 2401-001325 C-AL

5 CM605 2401-001496 C-AL

5 CM602 2401-001496 C-AL

5 CM399 2401-001496 C-AL

5 CM373 2401-001496 C-AL

5 CM312 2401-001496 C-AL

5 CM340 2401-001496 C-AL

5 CM343 2401-001496 C-AL

5 C603 2401-001496 C-AL

5 CM632 2401-000025 C-AL

5 C907

5 C902

5 C229

2401-000025

2401-000025

2401-000025

C-AL

C-AL

C-AL

5 C209

5 C213

5 C214

5 C228

2401-000025

2401-000025

2401-000025

2401-001989

C-AL

C-AL

C-AL

C-AL

5 CM623 2401-001998 C-AL

5 CM641 2401-002009 C-AL

5 CM357 2401-002144 C-AL

5 CM353 2401-002144 C-AL

5 C711 2401-000050 C-AL

5 C713 2401-000050 C-AL

5 C714

5 C717

2401-000050 C-AL

2401-000050 C-AL

5 CL06 2401-000050 C-AL

5 CM328 2401-000050 C-AL

5 C710 2401-000050 C-AL

C-AL

C-AL

C-AL

C-AL

C-AL

5 C702 2401-000050 C-AL

5 CM356 2401-002462 C-AL

5 C203

5 C202

2401-002462

2401-002462

C-AL

C-AL

5 CM618 2401-002463 C-AL

470nF,5%,63V,TP,-,5mm

100nF,5%,63V,TP,7.5x4.0x5.0m

100nF,5%,63V,TP,7.5x4.0x5.0m

100nF,5%,63V,TP,7.5x4.0x5.0m

100nF,5%,63V,TP,7.5x4.0x5.0m

100nF,5%,63V,TP,7.5x4.0x5.0m

100nF,5%,63V,TP,7.5x4.0x5.0m

100nF,5%,50V,TP,20x16x8.5,

4.7uF,20%,50V,GP,TP,5x11,5

22uF,20%,25V,GP,TP,5x11,5

10uF,20%,16V,GP,TP,3.5x5,5

10uF,20%,16V,GP,TP,3.5x5,5

10uF,20%,16V,GP,TP,3.5x5,5

1uF,20%,50V,GP,TP,3x5,5

1uF,20%,50V,GP,TP,3x5,5

1uF,20%,50V,GP,TP,3x5,5

1uF,20%,50V,GP,TP,3x5,5

1uF,20%,50V,GP,TP,3x5,5

1uF,20%,50V,GP,TP,3x5,5

1uF,20%,50V,GP,TP,3x5,5

1uF,20%,50V,GP,TP,4x7,5

1uF,20%,50V,GP,TP,4x7,5

1uF,20%,50V,GP,TP,4x7,5

1uF,20%,50V,GP,TP,5x11,5

1uF,20%,50V,GP,TP,5x11,5

2.2uF,20%,50V,BP,TP,5x11,5

2.2uF,20%,50V,GP,TP,5x11,5

2.2uF,20%,50V,GP,TP,3.5x5,5

22uF,20%,16V,GP,TP,5x5,5

22uF,20%,16V,GP,TP,5x5,5

22uF,20%,16V,GP,TP,5x5,5

330uF,20%,16V,GP,TP,8x11.5,5

330uF,20%,16V,GP,TP,8x11.5,5

330uF,20%,25V,GP,TP,10x12.5,5

4.7uF,20%,35V,GP,TP,4x5,5

4.7uF,20%,35V,GP,TP,4x5,5

4.7uF,20%,35V,GP,TP,4x5,5

470nF,20%,50V,GP,TP,3x5,5

47uF,20%,16V,GP,TP,5x7,5

47uF,20%,16V,GP,TP,5x7,5

47uF,20%,16V,GP,TP,5x7,5

47uF,20%,16V,GP,TP,5x7,5

47uF,20%,16V,GP,TP,5x7,5

47uF,20%,16V,GP,TP,5x7,5

47uF,20%,16V,GP,TP,5x7,5

47uF,20%,16V,GP,TP,5x7,5

100uF,20%,16V,GP,TP,6.3x11,5

100uF,20%,16V,GP,TP,6.3x11,5

100uF,20%,16V,GP,TP,6.3x11,5

100uF,20%,16V,GP,TP,6.3x11,5

100uF,20%,16V,GP,TP,6.3x11,5

100uF,20%,16V,GP,TP,6.3x11,5

100uF,20%,16V,GP,TP,6.3x11,5

4.7uF,20%,50V,BP,TP,5x11,5

1000uF,20%,25V,GP,TP,10x20,5mm

100uF,20%,16V,GP,TP,6.3x7,5

47uF,20%,16V,GP,TP,5x11,5

47uF,20%,16V,GP,TP,5x11,5

10uF,20%,16V,GP,TP,5x11,2.5

10uF,20%,16V,GP,TP,5x11,2.5

10uF,20%,16V,GP,TP,5x11,2.5

10uF,20%,16V,GP,TP,5x11,2.5

10uF,20%,16V,GP,TP,5x11,2.5

10uF,20%,16V,GP,TP,5x11,2.5

10uF,20%,16V,GP,TP,5x11,2.5

10uF,20%,16V,GP,TP,5x11,2.5

10uF,20%,16V,GP,TP,5x11,2.5

10uF,20%,16V,GP,TP,5x11,2.5

10uF,20%,16V,GP,TP,5x11,2.5

10uF,20%,16V,GP,TP,5x11,2.5

10uF,20%,16V,GP,TP,5x11,2.5

33uF,20%,16V,GP,TP,5x11,5

33uF,20%,16V,GP,TP,5x11,5

33uF,20%,16V,GP,TP,5x11,5

470uF,20%,16V,GP,TP,8x11.5,5

5 C705 2401-002463 C-AL 470uF,20%,16V,GP,TP,8x11.5,5

5 LM603 2701-000002 INDUCTOR-AXIAL 100uH,10%,4.2x9.8mm












5 LJ702 2701-000114 INDUCTOR-AXIAL 10uH,10%,2.5x3.4mm

5 L201 2701-000114 INDUCTOR-AXIAL 10uH,10%,2.5x3.4mm

5 L202

5 L203

5 L701

2701-000114

2701-000114

2701-000114

INDUCTOR-AXIAL

INDUCTOR-AXIAL

INDUCTOR-AXIAL

10uH,10%,2.5x3.4mm

10uH,10%,2.5x3.4mm

10uH,10%,2.5x3.4mm

5 L702

5 L704

2701-000114 INDUCTOR-AXIAL 10uH,10%,2.5x3.4mm


5 L902 2701-000114 INDUCTOR-AXIAL 10uH,10%,2.5x3.4mm

5 LJ701 2701-000116 INDUCTOR-AXIAL 10uH,10%,4.2x9.8mm


5 L205

5 L206

5 L102

5 L204

5 L101




2701-000169 INDUCTOR-AXIAL 3.9uH,10%,2.5x3.4mm

2701-000171 INDUCTOR-AXIAL 330nH,10%,2.5x3.4mm

5 L903

5 L901





5 LM308 2702-000120 INDUCTOR-RADIAL 15mH,5%,6.2x7.4mm

5 XTM601 2801-003750 CRYSTAL-UNIT

5 X901 2801-003937 CRYSTAL-UNIT

5 L104

5 L103

5 Z202

2901-000299

2901-000299

2903-001240

8MHZ,30PPM,28-AAA,22PF,80OH

12MHz,25ppm,28-AAM,30pF,30o

FILTER-EMI ON BOARD

FILTER-EMI ON BOARD

FILTER-CERAMIC

-,6A,UL/CSA,-,9x7.5,

-,6A,UL/CSA,-,9x7.5,

TR,5.5MHz,-,28dB,-,TP,-

5 Z201 2903-001040 FILTER-CERAMIC TR,5.5/6.0/6.5MHz,-,1dB,-

5 SWM716 3404-000244 SWITCH-TACT 15V,20mA,90-170gf,7.5x7mm,SP

5 SWM715 3404-000244 SWITCH-TACT



15V,20mA,90-170gf,7.5x7mm,SP

15V,20mA,90-170gf,7.5x7mm,SP

15V,20mA,90-170gf,7.5x7mm,SP






5 JB902 3812-000219 WIRE-NO SHEATH CU





15V,20mA,90-170gf,7.5x7mm,SP

15V,20mA,90-170gf,7.5x7mm,SP

15V,20mA,90-170gf,7.5x7mm,SP

15V,20mA,90-170gf,7.5x7mm,SP

15V,20mA,90-170gf,7.5x7mm,SP

TCWA,300V,52mm(TAPING)












5 JG006 3812-000219 WIRE-NO SHEATH CU





















5 JA5V09 3812-000219 WIRE-NO SHEATH CU






5 J273 3812-000219 WIRE-NO SHEATH CU

5 J275

5 J276

3812-000219 WIRE-NO SHEATH CU





















Loc. No.


5 JA33 3812-000219 WIRE-NO SHEATH CU



5 JB5V07 3812-000219 WIRE-NO SHEATH CU















5 JJ01 3812-000219 WIRE-NO SHEATH CU

5 JP01 3812-000219 WIRE-NO SHEATH CU








5 JPM303 3812-000219 WIRE-NO SHEATH CU


5 JTV500 3812-000219 WIRE-NO SHEATH CU

5 JTV501 3812-000219 WIRE-NO SHEATH CU

5 L703 3812-000219 WIRE-NO SHEATH CU




5 JP06

5 JP10




























5 J150

5 J151

5 J152

3812-000219

3812-000219

3812-000219

WIRE-NO SHEATH CU

WIRE-NO SHEATH CU

WIRE-NO SHEATH CU

5 J153

5 J158

5 J148

5 J142

5 J143

3812-000219

3812-000219

3812-000219

3812-000219

3812-000219

WIRE-NO SHEATH CU

WIRE-NO SHEATH CU

WIRE-NO SHEATH CU

WIRE-NO SHEATH CU

WIRE-NO SHEATH CU

5 J144

5 J146

5 J147

5 J159

5 J169

5 J170

5 J171

3812-000219

3812-000219

3812-000219

3812-000219

3812-000219

3812-000219

3812-000219

WIRE-NO SHEATH CU

WIRE-NO SHEATH CU

WIRE-NO SHEATH CU

WIRE-NO SHEATH CU

WIRE-NO SHEATH CU

WIRE-NO SHEATH CU

WIRE-NO SHEATH CU




























































































































































5 J185

5 J175

5 J176

5 J177

5 J178

5 J179

5 J196

5 J205

5 J209

5 J210

5 J211

5 J216

5 J203

5 J197

5 J198

5 J200

5 J201

5 J234

5 J235

5 J256

5 J257

5 J258

5 J186

5 J187

5 J189

5 J194

5 J195

5 J219

5 J222

5 J223

5 J231

5 J260

5 J261

5 J262

5 J264

5 J265

5 J259

5 J135

5 J174

5 J225

5 J226

5 J227

5 J228

5 J229

5 J224

5 J217

5 J218

5 J137

5 J138

5 J139

5 J140

5 J141

5 J136

5 J122

5 J123

5 J124

5 J125

5 J113

5 J117

5 J120

5 J109

5 D101

5 J103

5 J106

5 J107

5 J108

5 J121

5 J172

5 J173

5 J168

5 J160

5 J161

5 J162

5 J166

5 J167

5 J110

5 J111
















































































Loc. No.


4

4

3 Q813

4

4

4

3

4 D822

4 D823

4 D825

4 D827

4 D811

4 D812

4 D816

4 D820

4 D806

4 D828

3

3

3 D810

4

4

4

4

3 Q803

4

4


5 HIC01 AA13-20004W IC HYBRID


-,PAP103T,SIP,6P,PRE-AMP,TP

5 GT01

5 GT02

5 A

AA60-40014A PIN-GT,ASSY

AA60-40014A PIN-GT,ASSY

AA97-12501A ASSY SMD

AUTO

AUTO

CMC13410X/KMT

6 ICM301 1204-001649 IC-VIDEO PROCESS LA71598M,QFP,100P,-,PLA

6 PCB AA41-00549C PCB-MAIN TF20P1D4X,FR-1,1L,C,1.6T,330X2

6 AA97-06858A ASSY MICOM

7 ICM601 AA09-00261A IC MICOM

6 HA68-02176A LABEL

,C17A,UPD784928,SNM-740MD,011

UPD784927GF-230-3BA,TF20P1DF,1

LABEL

2

3

3 C612

3 C607

3

2401-000703 C-AL

2401-001998 C-AL

2200uF,20%,25V,GP,-,12.5x25mm,

1000uF,20%,25V,GP,TP,10x20,5mm

AA94-12224A ASSY PCB POWER C17A,20,RUSSIA,SEB&SDIHU

0202-000008 SOLDER-WIRE S63S-W3.0,S63S,D3,63Sn/37Pb,

0202-000187 SOLDER-WIRE FLUX -,RS60S,D1.2,63Sn/37Pb

3

3

0204-000442 SOLVENT

0204-001024 FLUX

1M-1000,C3H70H,96,-

DF-98TVS,-,20%,-

3 Q401 0502-001115 TR-POWER KSC5386,NPN,50W,TO-3PF,ST,8-

3 PC801S 0604-001038 PHOTO-COUPLER TR,130-260%,200mW,DIP-4,ST

3 PT801S 1404-000002 THERMISTOR-PTC 9ohm,20%,-,-,TR,RECT,-

3 NT801S 1404-001045 THERMISTOR-NTC 4.7ohm,15%,2900K,35.0mW,T

3 CY801S 2201-000446 C-CERAMIC,DISC 3.3NF,20%,400V,Y5U,TP,15X

3 CR402S 2306-001004 C-FILM,MPPF

3 CR410S 2306-000328 C-FILM,MPPF

3 CX801S 2306-000318 C-FILM,MPPF

300nF,5%,400V,TP,26x14x21mm,

6.8nF,5%,1.6KV,TP,28.5x18x10

220nF,20%,250V,TP,-,22.5mm

3 C805 2401-003030 C-AL

3 RL801S 3501-001040 RELAY-POWER


3 CN801B 3711-002645 CONNECTOR-HEADER

220uF,20%,450V,GP,BK,30x35,10

12VDC,500MW,10000MA,1FORMA,1

3 CN802B 3711-003975 CONNECTOR-HEADER



BOX,14P,1R,2.5mm,STRAIG

3 PCB+SC AA60-10008A SCREW-TAPPING -,SWRCH18A,M3,L10,TH,+,-,-

3 T801S AA26-00163A TRANS SWITCHING 35B125-DM,V17A,SMV-20A5S

3 T444S AA26-00171A TRANS FBT

3 T401

FCA173,TVDP,5.7MH,FEERITE,-,1.

AA26-50001B TRANS-HORIZ.DRIVE-,-,-,7.1mH,-,-,102uH,

3 LR401S AA27-30001B COIL LINEARITY -,195uH,QIC1010,PI0.4,4.5

3 L402 AA27-40001N COIL HORIZ. WIDTH -,90/260uH,SB-5S620,PI

3 LX801S AA29-30001D FILTER LINE NOISE SQ1913,-,6.0MH,0.8A,-

3 GT101A AA39-20010D LEAD CONNECTOR-ASSY ,1P,400,YFH800-01,S,

3 AA61-01045A SUPPORT-PCB DASS-T 9N,NYLON ,9.4,NTR

3 AA63-00518A SHIELD-CASE 20P1,SECC,T0.5,C17A

AA65-30018A CLAMPER CORE-WIRE

AA65-30111A CLAMPER CORE-WIRE

DONG-A,NYLON-66,-,-,-,

ALL MODEL,NYLON,V0,-,W

AA96-00243D ASSY H/S -,BRIDGE,AA62-00045A,D06U20S,D

0205-000129 GREASE-SILICON SC102,JAPAN

0402-001374 DIODE-RECTIFIER FFPF06U20S,200V,6A,TO-22

6003-000334 SCREW-TAPTITE

AA62-00065A HEAT SINK-PS

RH,+,2S,M3,L6,ZPC(YEL),SWR

DP,-,-,-,AA62-00045A,-,-,-,

AA96-00243G ASSY H/S -,POWER,AA62-00045A,C2073-H2,V

0205-000129 GREASE-SILICON SC102,JAPAN

0502-001007 TR-POWER KSC2073-H2,NPN,25W,TO-220,ST,6

4

4




DP,-,-,-,AA62-00045A,-,-,-,

3 IC301 AA96-00244A ASSY H/S

4 0205-000129 GREASE-SILICON

-,-,AA62-00046A,LA7840,-

SC102,JAPAN

4 1204-001483 IC-VERTICAL PROCESSO LA7840,SIP,7P,708MI

4

4




DP,-,-,-,AA62-00046A,-,-,-,

3 IC801S AA96-00662B ASSY H/S

4 0205-000129 GREASE-SILICON

-,POWER,AA62-30171J,KA5Q0765R,

SC102,JAPAN

4 1203-001932 IC-PWM CONTROLLER 5Q0765,TO-220F,5P,185M

6003-000333

AA62-30171J HEAT SINK-ES

AA96-50305D ASSY H/S

0502-000298

6003-000333

0401-000006

0402-000132

SCREW-TAPTITE

TR-POWER

SCREW-TAPTITE

AA62-30012E HEAT SINK-ES

RH,+,2S,M3,L10,ZPC(YEL),SW

-,-,-,SILVER,-,DREAM1,-,-,-

-,POWER,AA62-30012E,KSD73Y,STY

KSD73,NPN,30000mW,TO-220,TP,12

RH,+,2S,M3,L10,ZPC(YEL),SW

-,A6063 EXTR,-,-,TO-220 H55

AA97-13460A ASSY AUTO-POWER C17A,20,RUSSIA,SEB&SDIH









DIODE-SWITCHING BAV21,250V,250mA,DO-35,T

DIODE-RECTIFIER 1N4004,400V,1A,DO-41,TP


4 D815

4 D301

4 D405

4 D809

4 D814





0402-000493 DIODE-RECTIFIER 1R5GU41,400V,1.5A,DO-15L

4 D404

4 D808

4 D403

4 D402

0402-000534

0402-001105

0402-001105

0402-001105

DIODE-RECTIFIER

DIODE-RECTIFIER

DIODE-RECTIFIER

DIODE-RECTIFIER

RG10V,400V,1.2A,DO-201,T

ERB43-04SV1,400V,1.0A,-,

ERB43-04SV1,400V,1.0A,-,

ERB43-04SV1,400V,1.0A,-,

4 D804S 0402-001111 DIODE-RECTIFIER 1N5397GP,600V,1.5A,DO-20




4 D807 0402-001443 DIODE-RECTIFIER EGP20K,800V,2A,DO-15,TP

4 DZ401 0403-000508 DIODE-ZENER MTZJ5.6B,5.6V,5.45-5.73V,500

4 DZ807 0403-000699 DIODE-ZENER

4 DZ303 0403-000700 DIODE-ZENER

4 DZ810 0403-000700 DIODE-ZENER

4 DZ811 0403-000714 DIODE-ZENER

4 DZ805 0403-000714 DIODE-ZENER

TZP27B,27V,27-30.8V,1W,DO-41

TZP33A,33V,31-35V,1W,DO-41,T

TZP33A,33V,31-35V,1W,DO-41,T

MTZJ3.3B,3.3V,3.32-3.53V,500

MTZJ3.3B,3.3V,3.32-3.53V,500

4 Q810

4 Q811

4 Q812

4 Q402

4 Q805

4 Q806

4 Q807

4 Q804

4 Q808

4 Q801

4 DZ804 0403-000720 DIODE-ZENER

4 DZ808 0403-001211 DIODE-ZENER

4 DZ803 0403-001211 DIODE-ZENER

4 DZ302 0403-001221 DIODE-ZENER

4 DZ806 0403-001318 DIODE-ZENER

4 DZ802 0403-001327 DIODE-ZENER

4 DZ301 0403-001328 DIODE-ZENER

4 DZ304 0403-001328 DIODE-ZENER

4 DZ813 0403-001373 DIODE-ZENER

4 DZ812 0403-001373 DIODE-ZENER

0501-000362

0501-000362

0501-000362

0501-000369

0501-000389

1203-001217

MTZJ9.1B,9.1V,8.57-9.01V,500

MTZJ12B,11.44-12.03V,500MW,D

MTZJ12B,11.44-12.03V,500MW,D

UZ39BSB,35.36-37.19V,500MW,D

MTZJ4.3B,4.17-4.43V,500mW,DO

MTZJ18A,16.22-17.06V,500mW,D

MTZJ22A,20.15-21.20V,500mW,D

MTZJ22A,20.15-21.20V,500mW,D

MTZJ5.1A,4.81V-5.07V,500mW,D

MTZJ5.1A,4.81V-5.07V,500mW,D

TR-SMALL SIGNAL KSA2328A-Y,NPN,1W,TO-92L



TR-SMALL SIGNAL KSC2331-Y,NPN,1000mW,TO-


0501-000398 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,T

0501-000398 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,T

0504-000142 TR-DIGITAL

0504-000142 TR-DIGITAL

IC-POSI.ADJUST REG.

KSR2001,PNP,300MW,4.7K/4.7K,T

KSR2001,PNP,300MW,4.7K/4.7K,T

431,TO-92,3P,4.58MIL

4 R824

4 R840

4 R835

4 R816

4 R821

4 R809

4 R822

4 R831

4 R841

4 R842

4 VX801S 1405-000187 VARISTOR

4 R301 2001-000016 R-CARBON(S)

4 R408

4 R829

4 R825

2001-000022

2001-000028

2001-000028

R-CARBON(S)

R-CARBON(S)

R-CARBON(S)

4 R823

4 R808

4 R828

4 R405

4 R814

2001-000037

2001-000109

2001-000117

2001-000117

2001-000281

R-CARBON(S)

R-CARBON(S)

R-CARBON(S)

R-CARBON(S)

R-CARBON

2001-000302

2001-000429

2001-000429

2001-000429

2001-000515

R-CARBON

R-CARBON

R-CARBON

R-CARBON

R-CARBON

2001-000522 R-CARBON

2001-000660 R-CARBON

2001-000734 R-CARBON

2001-000734 R-CARBON

2001-000734 R-CARBON

750V,1250A,12.5x7mm,TP

1OHM,5%,1/2W,AA,TP,2.4X6.4MM

33OHM,5%,1/2W,AA,TP,2.4X6.4M

100OHM,5%,1/2W,AA,TP,2.4X6.4

100OHM,5%,1/2W,AA,TP,2.4X6.4

330OHM,5%,1/2W,AA,TP,2.4X6.4

470OHM,5%,1/2W,AA,TP,2.4X6.4

68OHM,5%,1/2W,AA,TP,2.4X6.4M

68OHM,5%,1/2W,AA,TP,2.4X6.4M

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

10OHM,5%,1/8W,AA,TP,1.8X3.2MM




220OHM,5%,1/8W,AA,TP,1.8X3.2MM



4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

4 R843

4 R811

4 R827

4 R817

4 R407

2001-000734 R-CARBON

2001-000800 R-CARBON

2001-000812 R-CARBON

2001-000924 R-CARBON

2001-001037 R-CARBON(S)

4 R813

4 R812

2001-001078 R-CARBON(S)

2001-001078 R-CARBON(S)

4 R410 2001-001078 R-CARBON(S)

4 R422S 2001-001088 R-CARBON(S)

4 R409 2001-001114 R-CARBON(S)

4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M

5.1KOHM,5%,1/8W,AA,TP,1.8X3.2M

5.6KOHM,5%,1/8W,AA,TP,1.8X3.2M

680OHM,5%,1/8W,AA,TP,1.8X3.2MM

0.39OHM,5%,1/2W,AA,TP,2.4X6.

15KOHM,5%,1/2W,AA,TP,2.4X6.4

15KOHM,5%,1/2W,AA,TP,2.4X6.4

15KOHM,5%,1/2W,AA,TP,2.4X6.4

1KOHM,5%,1/2W,AA,TP,2.4X6.4M

270OHM,5%,1/2W,AA,TP,2.4X6.4

4 R818

4 R838

4 R839

4 R830

4 R806

2001-001134

2001-001150

2001-001150

2001-001170

2001-001170

R-CARBON(S)

R-CARBON(S)

R-CARBON(S)

R-CARBON(S)

R-CARBON(S)

360ohm,5%,1/2W,AA,TP,2.4x6.4

470KOHM,5%,1/2W,AA,TP,2.4X6.

470KOHM,5%,1/2W,AA,TP,2.4X6.

6.8OHM,5%,1/2W,AA,TP,2.4X6.4

6.8OHM,5%,1/2W,AA,TP,2.4X6.4

4 R810 2001-001192 R-CARBON(S) 820OHM,5%,1/2W,AA,TP,2.4X6.4

4 RX801S 2002-001011 R-COMPOSITION 3.3Mohm,5%,1/2W,AA,TP,3.7x



Loc. No.


4 R833

4 R815

4 R302

4 R415

4 R406

4 R404

4 R414

4 R317

4 R411

4 C302

4 RY801S 2002-001012 R-COMPOSITION 8.2Mohm,5%,1/2W,AA,TP,3.7x

4 R805 2003-000586 R-METAL OXIDE(S) 22Kohm,5%,2W,AF,TP,4x12

4 R804

4 R803

4 R315

2003-000586

2003-000586

2003-001018

R-METAL OXIDE(S) 22Kohm,5%,2W,AF,TP,4x12

R-METAL OXIDE(S) 22Kohm,5%,2W,AF,TP,4x12

R-METAL OXIDE(S) 220ohm,5%,2W,AF,TP,3.9x

4 R303

4 R402

4 R413

4 R412

4 R306

2003-002070 R-METAL OXIDE

2004-001137 R-METAL

2004-001373 R-METAL(S)

2004-001390 R-METAL(S)

1ohm,5%,2W,AF,TP,3.9x10mm

2003-002178 R-METAL OXIDE(S) 1Kohm,5%,2W,AG,TP,3.9x1

6.8Kohm,1%,1/8W,AA,TP,1.8x3.2m

100Kohm,1%,1/2W,AA,TP,2.4x6.4

1Kohm,2%,1/2W,AA,TP,2.4x6.4mm

2004-001983 R-METAL(S)

2004-004089 R-METAL(S)

2004-004969 R-METAL(S)

2008-000253 R-FUSIBLE(S)

2008-000253 R-FUSIBLE(S)

2008-000253 R-FUSIBLE(S)

2008-000264 R-FUSIBLE(S)

2008-001013 R-FUSIBLE(S)

2008-001015 R-FUSIBLE(S)

2.49Kohm,1%,1/2W,AA,TP,2.4x6.

123Kohm,1%,1/2W,AA,TP,2.5x6.5

1.1Kohm,1%,1/2W,AA,TP,2.4x6.4

0.47ohm,5%,1W,AF,TP,3.9x10m

0.47ohm,5%,1W,AF,TP,3.9x10m

0.47ohm,5%,1W,AF,TP,3.9x10m

1ohm,5%,1W,AF,TP,3.9x10mm

1.2ohm,5%,2W,AF,TP,3.9x10mm

1.5ohm,5%,2W,AF,TP,3.9x10mm

2201-000259 C-CERAMIC,DISC 0.18NF,10%,500V,Y5P,TP,5.

4 C826

4 C824

4 C809

4 C816

4 C807

4 C310

4 C407

4 C411

4 C806

4 C309

4 C801

4 C817

4 C818

4 C305

4 C303

2201-000332 C-CERAMIC,DISC 2.2NF,20%,250V,Y5U,TP,9X4

2201-000374 C-CERAMIC,DISC 0.22NF,5%,50V,C0G,TP,10.5




4 C814

4 C408



4 CR404S 2201-000639 C-CERAMIC,DISC 0.68NF,10%,2KV,Y5P,TP,9X5

4 C812 2201-000991 C-CERAMIC,DISC 0.56NF,10%,2KV,Y5P,TP,7.5

4 C825 2202-000121 C-CERAMIC,MLC-AXIAL 100pF,10%,50V,Y5P,TP

2202-000121 C-CERAMIC,MLC-AXIAL 100pF,10%,50V,Y5P,TP

2202-000632 C-CERAMIC,MLC-AXIAL 100nF,20%,50V,Z5U,TP

2301-000016 C-FILM,PEF

2301-000224 C-FILM,PEF

2301-000235 C-FILM,PEF

2301-000254 C-FILM,PEF

2301-000383 C-FILM,PEF

2301-001065 C-FILM,MPPF

2301-001435 C-FILM,PPF

2305-000149 C-FILM,MPEF

22nF,5%,100V,TP,7.2x4.5x9.0mm

22nF,5%,50V,TP,7.4x3.9x13mm,5

3.9nF,5%,50V,TP,6.5x3.0x5.5mm

39nF,5%,50V,TP,7.5x3.5x6.5mm,

10nF,5%,50V,TP,6x7x3.2mm,5mm

47nF,5%,630V,TP,19x15.5x7,7.

1.5nF,5%,1.2kV,TP,15x8x12.5mm

100nF,5%,100V,TP,12x12.5x6.5

4 C808

4 C306

4 C820

4 C823

4 C406

4 C308

4 C819

4 L401

4

4 L404

4 C301 2305-000285 C-FILM,MPEF

4 CR405S 2305-000382 C-FILM,MPEF

4 C810

4 C821

4 C813

2305-000665

2305-000665

2401-000262

C-FILM,MPEF

C-FILM,MPEF

C-AL

4 C307

4 C815

4 C827

4 C401

4 C304

2401-000365

2401-000703

2401-000901

2401-000927

2401-001115

C-AL

C-AL

C-AL

C-AL

C-AL

2401-001192

2401-001397

2401-002144

2401-002144

2401-002619

C-AL

C-AL

C-AL

C-AL

C-AL

220NF,5%,100V,TP,10.5X5.5X15

4.7nF,5%,400V,TP,-,5mm

100nF,5%,63V,TP,7.5x4.0x5.0m

100nF,5%,63V,TP,7.5x4.0x5.0m

100uF,20%,160V,HR,TP,16x25,7.5

100uF,20%,50V,WT,TP,10x12.5mm,

2200uF,20%,25V,GP,-,12.5x25mm,

22uF,20%,160V,GP,TP,10x20,5

22uF,20%,250V,GP,TP,13x20,5

330uF,20%,25V,GP,TP,10x12.5,5

33uF,20%,50V,GP,TP,6.3x11,5

470uF,20%,25V,GP,TP,10x16,5

47uF,20%,16V,GP,TP,5x11,5

47uF,20%,16V,GP,TP,5x11,5

47uF,20%,25V,GP,TP,5x11,5

2401-003028 C-AL

2401-003139 C-AL

100uF,20%,25V,WT,TP,6.3x11,5

1000uF,20%,25V,WT,TP,10*20,5mm


0203-001123 TAPE-PAPER #53131,T0.15,W6.0,L200000,YEL


4 L302

4 L301

4 L405

4 J804

4 L804




2701-001030 INDUCTOR-AXIAL 43uH,10%,5x14mm

2901-000297 FILTER-EMI ON BOARD -,3A,-,-,3.5x5,TP,-

4 L403

4 L803

2901-000297 FILTER-EMI ON BOARD -,3A,-,-,3.5x5,TP,-

3301-001223 CORE-FERRITE BEAD AA,62ohm,3.5x0.8x5mm,-

4 L802 3301-001223 CORE-FERRITE BEAD AA,62ohm,3.5x0.8x5mm,-

4 FP801S 3601-000261 FUSE-CARTRIDGE 250V,3.15A,TIME-LAG,GLASS

4 FD801S 3601-001086 FUSE-AXIAL LEAD 125V,5A,FAST-ACTING,GLAS

4 FD802S 3601-001086 FUSE-AXIAL LEAD 125V,5A,FAST-ACTING,GLAS

4 F801B 3602-000114 FUSE-HOLDER -,-,30mohm

4 F801A 3602-000114 FUSE-HOLDER


-,-,30mohm


4 J817 3812-000219 WIRE-NO SHEATH CU TCWA,300V,52mm(TAPING)

4 J815

4 J814






4 J813

4 J824

4 J822

4 J821

4 J820

4 J819

4 J812

4 J806

4 J805

4 J803





















4 J802

4 J801

4 J811

4 J810

4 J809











4 J808

4 J807



4 PCB AA41-00548B PCB-POWER

4 EY811 6042-000002 EYELET

4 EY812 6042-000002 EYELET



TF21B5S,FR-1,1L,A,1.6T,245X245

ID1.5,OD2,L2.8,NI+SN,BSP3-1/2H


4 EY813 6042-000002 EYELET

4 EY814 6042-000002 EYELET

4 EY815 6042-000002 EYELET

4 EY802 6042-000002 EYELET

4 EY803 6042-000002 EYELET

4 EY804 6042-000002 EYELET

4 EY805 6042-000002 EYELET

4 EY806 6042-000002 EYELET

4 EY816 6042-000002 EYELET

4 EY822 6042-000002 EYELET

4 EY825 6042-000002 EYELET

4 EY827 6042-000002 EYELET

4 EY828 6042-000002 EYELET

4 EY829 6042-000002 EYELET

4 EY817 6042-000002 EYELET

4 EY818 6042-000002 EYELET

4 EY819 6042-000002 EYELET

4 EY820 6042-000002 EYELET

4 EY821 6042-000002 EYELET

4 EY801 6042-000002 EYELET





















4 EY406 6042-000002 EYELET

4 EY407 6042-000002 EYELET

4 EY408 6042-000002 EYELET

4 EY409 6042-000002 EYELET

4 EY410 6042-000002 EYELET

4 EY401 6042-000002 EYELET

4 EY402 6042-000002 EYELET

4 EY403 6042-000002 EYELET

4 EY404 6042-000002 EYELET

4 EY405 6042-000002 EYELET

4 EY411 6042-000002 EYELET

4 EY419 6042-000002 EYELET

4 EY420 6042-000002 EYELET

4 EY421 6042-000002 EYELET

4 EY422 6042-000002 EYELET

4 EY423 6042-000002 EYELET

4 EY412 6042-000002 EYELET

4 EY414 6042-000002 EYELET

4 EY415 6042-000002 EYELET

4 EY416 6042-000002 EYELET

4 EY417 6042-000002 EYELET

4 EL802 6042-000001 EYELET

4 EL803 6042-000001 EYELET

4 EL804 6042-000001 EYELET

4 EL805 6042-000001 EYELET

4 EL801 6042-000001 EYELET

4 EL301 6042-000001 EYELET

4 EL302 6042-000001 EYELET

4 EL403 6042-000001 EYELET

4 EL404 6042-000001 EYELET

4 GT805 AA60-40014A PIN-GT,ASSY



























AUTO

AUTO

AUTO

AUTO

AUTO

AUTO

AUTO


ID2.2,OD2.7,L3.1,NI+SN,BSP3-1/











Loc. No.


3

3

4

2

3






HA68-02176A LABEL

AUTO

AUTO

AUTO

AUTO

AUTO

AA95-01756G ASSY SUB-PCB CRT ,C17A20,21,PAL ALL SE

0202-000008

0202-000187

0204-000442

SOLDER-WIRE

SOLDER-WIRE FLUX -,RS60S,D1.2,63Sn/37Pb

SOLVENT

LABEL

S63S-W3.0,S63S,D3,63Sn/37Pb,

1M-1000,C3H70H,96,-

3 0204-001024 FLUX

3 V999S 3704-001105 SOCKET-CRT

DF-98TVS,-,20%,-

11P,20PI,26.5PI,NI,-

3 CN502B AA39-20052A LEAD CONNECTOR-ASSY ,4P,300,YBNH025-04,Y

3 CN501B AA39-20069A LEAD CONNECTOR-ASSY ,5P,500,YBNH025-05,6

3 IC501 AA96-00842A ASSY H/S ,VIDEO,AA62-30175D,TDA6107Q

4 IC501 1201-001159 IC-VIDEO AMP

4 SCR501 6003-000334 SCREW-TAPTITE

6107,ZSIP,9P,-,SINGLE,-,PLA


4 H/S501 AA62-30175D HEAT SINK-PS

3 AA97-05570A ASSY AUTO-SUB

-,SECC,T1.0,-,33X15X30 FT-2

14/20/21,C17A,PAL

4 D502 0402-000132 DIODE-RECTIFIER 1N4004,400V,1A,DO-41,TP

4 D503

4 D504



4 D501 0402-000254 DIODE-RECTIFIER RGP10J,600V,1A,DO-41,TP

4 DZ501 0403-000508 DIODE-ZENER MTZJ5.6B,5.6V,5.45-5.73V,500

4 R507 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM

4 R508

4 R509

2001-000281 R-CARBON

2001-000281 R-CARBON

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

100OHM,5%,1/8W,AA,TP,1.8X3.2MM

4 R506 2001-001062 R-CARBON(S) 10MOHM,5%,1/2W,AA,TP,2.4X6.4

4 R501H 2002-001008 R-COMPOSITION 1.8Kohm,10%,1/2W,AA,TP,3.7

4 R502H 2002-001008 R-COMPOSITION 1.8Kohm,10%,1/2W,AA,TP,3.7

4 R503

4 C503

4 C501

4 C502

4 C506

2002-001008 R-COMPOSITION 1.8Kohm,10%,1/2W,AA,TP,3.7

2201-000723 C-CERAMIC,DISC 4.7NF,20%,3KV,Y5U,TP,16X5

2202-000825 C-CERAMIC,MLC-AXIAL 680pF,10%,50V,Y5P,TP

2301-000213 C-FILM,PEF 220nF,5%,250V,TP,21.5x11,7.5

2401-000430 C-AL 10uF,20%,250V,GP,TP,10x16mm,5m

4 C504 2401-001232 C-AL

4 JC500 3812-000219 WIRE-NO SHEATH CU

4.7uF,20%,250V,GP,TP,10x12.5,5


4 JC501 3812-000219 WIRE-NO SHEATH CU

4 PCB AA41-00550A PCB-CRT


TF21B5S,FR-1,1L,A,1.6T,330X245

4 GT502 AA60-40014A PIN-GT,ASSY AUTO

2 AA95-01822B ASSY SUB-PCB,MASTER 20P1,C17A,AA95-01615

3 SW811S 3403-001134 SWITCH-PUSH 250V,5A,DPST,ON-OFF,-

3 6001-000057 SCREW-MACHINE RH,+,M3,L6,ZPC(BLK),SWRCH1

3 CN801 AA39-00206B LEAD CONNECTOR-ASSY ,2P,400MM,YFH800-02,

3 AA61-10320A BRACKET-MASTER T3350,SECC,T1.0,-,-,-,-

3

4 PCB

AA97-05602A ASSY AUTO-SUB 20P1,C17A

AA41-00587A PCB-MASTER 20P1,FR-1,1L,A,1.6T,245X245,C

4 EY801 6042-000002 EYELET

4 EY802 6042-000002 EYELET

4 EY803 6042-000002 EYELET




3

2

2

3

3

4 EY804 6042-000002 EYELET

4 EY805 6042-000002 EYELET

4 EY806 6042-000002 EYELET

4 GTM801 AA60-40014A PIN-GT,ASSY

4 GTM802 AA60-40014A PIN-GT,ASSY




AUTO

AUTO

AA96-01127B ASSY POWER CORD DP,AA39-10001M,CP2,H/C40

AA39-10001M CBF POWER CORD -,KJP-140,KLCE-2F,2.4m,HO

AA61-20284A HOLDER P-CORD,PP,-,-,-,BLK,VO,KE-002

AA64-03102W DOOR-HOUSING 14P1,20P1(SEH),ABS HB,BLK,S

HA83-00040A LP-MARKING PAINT ,METALLIC SILVER,SV-012

2

2

3

3

3

HA83-00006A LP-RESIN HIPS

HA83-00012A LP-RESIN

,BASF495F,NTR,HB

,M BATCH,WILSON 6053-GY-60,GRY

AA61-00050A SPRING ETC-DOOR TVCR TVI,SUS304,-,-,-,-,

AA90-00947A ASSY-FULL DECK 2HD,SVTS-M2P/XEC

AA91-00741A ASSY-DECK ,SCORPIO TOSHIBA

3

2

3

3

AA91-00744A ASSY-DRUM

6006-001092 SCREW-ASS’Y MACH WS,PH,+,M3.0,L6.0,ZPC(Y

AA90-02598A ASSY COVER MISC-FRAMESEH TVCR,STYX C17A

3 DE+FD 6003-001268 SCREW-TAPTITE

,2HD,NON-DLC,SCORPIO

AA91-00782A ASSY-S-IMP ROLLER ,PAL 2HD SESA,TF14N53,

TH,+,B,M4.0,L12.0,ZPC(YEL)

3

2

3

3

3 PW+FD 6003-001268 SCREW-TAPTITE

3 FD+BF 6003-001023 SCREW-TAPTITE

3

AA61-00862A FRAME-DECK

AA61-01214A BRACKET-FRAME

AA63-00520A SHIELD-BOTTOM

TH,+,B,M4.0,L12.0,ZPC(YEL)

RWH,+,B,M3,L10,ZPC(YEL),SW

S-PJT,HIPS V0,BLK,ONE-BOARD

,SECC,T1.0

20A5S,SPTE,T0.3

AA63-00521A SHIELD-DRUM 20A5S,SECC,T0.5

AA65-30009A CLAMPER CORE-FBT -,ABS,V0,-,BLK,-

1

1

2

2

2

1

2

3

3

2

2

1

2

2

2


ASSY COVER FRONT

1 AA90-03682A ASSY COVER FRONT TW20P14X/BWT

3

3

4

4

3

4

3

4

4

4

2 CRT+CF AA60-10050Q SCREW-ASSY -,SWRCH18A,M5,L26.5,HH,+,WC,-

2 CB+CF 6002-000515 SCREW-TAPPING RH,+,2,M4,L15,ZPC(WHT),SWR

2 AA65-30107A CLAMPER CORE-D,COIL 20~22 INCH,NYLON 66,

2 AA96-01028A ASSY COVER P-FRONT 20P1,HB,SV-012P

3 KF+CF 6003-001019 SCREW-TAPTITE

3 WIN+CF 6003-001019 SCREW-TAPTITE

3 SPK+CF 6003-001023 SCREW-TAPTITE

3 AA61-60003J SPRING ETC-CS

3 AA64-02325H KNOB-POWER

RH,+,B,M4,L12,ZPC(BLK),SWR

RH,+,B,M4,L12,ZPC(BLK),SWR


-,SUS304,-,-,OD6,N7,OD6,-,

14.20P1 SEH,ABS,HB,G3676,SV01




AA64-02326H KNOB-FAMILY

,BASF495F,NTR,HB


14.20P1 SEH,ABS,HB,G3676,SV0




,BASF495F,NTR,HB


AA64-02327A DECORATION-POWER

AA64-02328A WINDOW-LED

20P1,PC,HB,SEMI-VIOLET

14.20P1,PC,CLR

AA64-03104A CABINET-FRONT 20P1 SEH,HIPS,HB,G7666,SV0

4

3

4

4

3


HA83-00006A LP-RESIN HIPS ,BASF495F,NTR,HB


AA64-70010B BADGE-BRAND


-,AL,-,-,L50,-,SILVER,SS R20

0203-001290 TAPE-OPP MASKING ANT 100C,T0.073,W30,L50

2

2

3

3

3001-001186

HA60-00140A SPACER-GUM

HA68-02177B

SPEAKER

2 KP+CF 6003-001023 SCREW-TAPTITE

3W,8OHM,80°æ2DB,270HZ

AA39-20501A LEAD CONNECTOR-ASSY ,3(2),200,67096-003,


2

2 qms

HA68-02179A LABEL-RATING

HA83-00052A LP-TAPE-INK

2 rating HA83-00052A LP-TAPE-INK

LABEL-RATING;58MM,53MM,WHIT

,WIDTH 55 MM

,WIDTH 55 MM

ASSY COVER REAR

AA90-03734A ASSY COVER REAR TW20P14X/BWT

AA64-02322D CABINET-BACK



20P1,HIPS,FV2,G4309

,BASF495F,NTR,HB


AA65-30008A CLAMPER CORE-CORD

HA68-02179A LABEL-RATING

-,PE,HB,-,BLK,-

LABEL-RATING;58MM,53MM,WHIT

ASSY BOX

AA92-07410A ASSY BOX

AA69-01585B PACKING CASE

HA68-02178A LABEL-BOX

HA83-00046A LP-TAPE INK

20P

20P1 SEH,CB D-1 BB,A1,YEL,G

LABEL-BOX;250MM,89MM,WHITE

,WIDTH 105 MM

ASSY P/MATERIAL

AA92-03070B ASSY P/MATERIAL 20P1

AA81-00112A TAPE-OPP,MASKING CRL,W75

AA69-00744C BAG-SHEET

AA69-01472A CUSHION-SET

-,HDPE PE FOAM,T0.015,W1050,H9

20P1,PS FOAMED,C=0.02

ASSY ACCESSORY

AA92-06494A ASSY ACCESSORY TW20P14X/BWT



Loc. No.

2

2

2

2

2

2

2


AA59-00221E REMOCON

4301-000121 BATTERY-MN

,TM66,SAA5554PS,38,G6671B,S/S,

1.5V,-,AAA,10.5x44.5m,HOLDER

HA69-00276A BAG VINYL HDPE,T0.025,L400,W240,-,W/O LO

AA68-02264A MANUAL USERS ,RUS,W/P100(G),2,B5,C17A,56

HA68-00816B CARD WARRANTY RUSSINA,2,W/P 120G,BOTH FA

AA68-01120A MANUAL SERVICE -,-,CIS,A4,6PAGE(FOLD),W/

6801-001073 CARD-REGISTRATION RUS,XEV,RUS,MOJO100,-,

ASSY CPT

1 AA91-05783A ASSY CPTC17A,20,SEB&SDIHU,A48ECR43X52

2 LC801S AA27-20003Y COIL DEGAUSSING -,20,15.2ohm,28T,L2170,E

2 AA03-00280A CRT COLORA48ECR43X,+380MG,1.85MH,28.7MH

2 AA98-70031A ASSY TBC WIRE(P) DP,20,AA98-70014B,1P,TV




MEMO


Block Diagrams

8. Block Diagrams

8-1 Notes

The TVCR’s 1st and 2nd tuners are “multi-system.” compatible:

IC201S (TDA9361/9381) is the video, chroma, and deflection (UOC) IC .

8-1-1 TAPE PLAYBACK (REGARDLESS OF ORIGINAL RECORDING SYSTEM)

If the output PB signal of micom pin 12 is high, the PB signal outputs from ICM301 pin 29, passes through IC 702 pins 2 and 3 and out to another VCR . The output signal of IC701 pin 1 (pin 15) outputs from IC201S pin 42 .

8-1-2 VIEWING NORMAL CHANNEL WHILE RECORDING A SCRAMBLED CHANNEL:

The output CVBS (Composite Video Signal) of the 2nd IF outputs to IC702 pin 3 when the VCRmicom’s pin 13 (VCR tuner high) is high . The decoded signal goes to IC701 pin 2, where it is fed to IC 701 pin

9 (high output of VCR micom’s’ pin 11— AV/Tuner), and out to VCR pin 4 for recording.

8-1-3 VIEWING A SCRAMBLED CHANNEL WHILE RECORDING AN UNSCRAMBLED CHANNEL.

The output CVBS of the 2nd IF is fed from IC701 pin 5 to IC701 pin 4 (low output of VCR micom pin 11—AV/tuner). Then it goes to the VCR PART pin 4 for recording.

The scrambled signal (CVBS) is fed to IC702 pin 1 through the 1st IF, and then to IC702 pin 3.

Then it goes to the decoder input. The descrambled signal goes to IC701 pins 2 and 15, and then to

IC201S pin 42, where it outputs as RGB.

8-1-4 SYNCHRONOUS RECORDING:

The viewer sees the signal from the 1st tuner , while the signal from the second tuner is recorded.

Audio processing for the French system type is shown in the table.


Block Diagrams

8-2 C17A PCB Layout


9. Wiring Diagram

9-1 C17A Wiring Diagram

Samsung Electronics

Wiring Diagram

9-1

10. Schematic Diagrams

10-1 MAIN1 ( VCR SYSTEM BLOCK )

TP04

TP02

TP06

TP01

TP05

TP03

Samsung Electronics

TP05

TP06

TP03

TP04

Schematic Diagrams

TP01

TP02

10-1

Schematic Diagrams

10-2 MAIN2 ( VOC & TUNER BOX)


10-3 MAIN3 ( VCR A/V BLOCK )

TP09

TP07

Samsung Electronics

TP08

TP10

TP11

Schematic Diagrams

TP01

TP02

TP03

TP04

TP05

10-3

Schematic Diagrams

10-4 MAIN4 ( SWITCHING BLOCK)


10-5 MAIN5( OPTION-PAL HIFI BLOCK )

Samsung Electronics

Schematic Diagrams

10-5

Schematic Diagrams

10-6 MAIN6 ( OPTION-VCR SECAM BLOCK )


10-7 POWER & FBT

Samsung Electronics

Schematic Diagrams

10-7

Schematic Diagrams

10-8 CRT


10-9 FRONT A/V, MASTER SW

FRONT A/V MASTER SW

Schematic Diagrams


No results