HP Color LaserJet CP2025 Printer series User guide
HP Color LaserJet CP2025 Printer series is a reliable and efficient printing solution for home and small office use. With its advanced features and capabilities, this printer series delivers high-quality color prints, fast print speeds, and easy operation. Whether you need to print professional-looking documents, vibrant marketing materials, or eye-catching photos, the HP Color LaserJet CP2025 Printer series has you covered.
Advertisement
Advertisement
HP Color LaserJet CP2020 Series
User Guide
Copyright and License
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws.
The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Edition 2, 09/2008
Part number: CB493-90908
Trademark Credits
Adobe ® , Acrobat ® , and PostScript ® are trademarks of Adobe Systems Incorporated.
ENERGY STAR ® and the ENERGY STAR logo ® are U.S. registered marks of the United
States Environmental Protection Agency.
Corel® is a trademark or registered trademark of Corel Corporation or Corel
Corporation Limited.
Microsoft®, Windows®, and Windows®XP are U.S. registered trademarks of Microsoft
Corporation.
Windows Vista™ is either a registered trademark or trademark of Microsoft
Corporation in the United States and/or other countries.
Table of contents
ENWW iii
4 Use the product with Macintosh
View embedded Web server using a Macintosh ............................................... 29
Network configuration page .............................................................. 38
Configuration page ........................................................................... 38
Show or hide the IP address on the control panel ............................................ 40
Dynamic Host Configuration Protocol (DHCP) ................................. 41
Subnet mask ..................................................................................... 42
iv ENWW
Default gateway ................................................................................ 42
ENWW v
vi
ENWW
Use HP ToolboxFX to troubleshoot print-quality problems ............................ 117
Appendix A Supplies and accessories
Appendix B Service and support
ENWW vii
Appendix D Regulatory information
Multiple returns (two to eight cartridges) ........................................ 142
Single returns ................................................................................. 142
Disposal of waste equipment by users in private households in the European
viii ENWW
1 Product basics
●
●
●
ENWW 1
Product comparison
HP Color LaserJet CP2020 Series Printer
● Prints up to 21 pages per minute (ppm) on letter-size media.
● 50-sheet multipurpose tray (tray 1) and 250-sheet input tray (tray 2)
● Optional 250-sheet input tray (tray 3) (standard on HP Color LaserJet CP2020x)
● Hi-Speed universal serial bus (USB) 2.0 port
● Built-in networking to connect to 10Base-T/100Base-TX networks (HP Color LaserJet CP2020n,
HP Color LaserJet CP2020dn, and HP Color LaserJet CP2020x)
● Automatic duplexer (HP Color LaserJet CP2020dn and HP Color LaserJet CP2020x)
Product features
Memory
Supported operating systems
Paper handling
Printer driver features
Interface connections
Environmental features
● Prints up to 21 pages per minute (ppm) on letter-size media.
● Prints at 600 dots per inch (dpi).
● Includes adjustable settings to optimize print quality.
● The print cartridges use HP ColorSphere toner. For information about the number of pages the cartridges can print, see www.hp.com/go/pageyield . Actual yield depends on specific use.
● Offers automatic duplexing (HP Color LaserJet CP2020dn and HP Color LaserJet
CP2020x only).
● Includes 128-megabyte (MB) random-access memory (RAM).
● Windows 2000
● Windows XP Home/Professional
● Windows Server 2003 (32-bit only)
● Windows Vista
● Mac OS X V10.28 and later
● Tray 1 (multipurpose tray) holds up to 50 sheets of print media or 10 envelopes.
● Tray 2 holds up to 250 sheets of print media.
● Optional Tray 3 holds up to 250 sheets of print media.
● Output bin holds up to 125 sheets of print media.
● ImageREt 3600 produces 3600 dpi print quality for fast, high-quality printing of business text and graphics.
● Includes a Hi-Speed USB 2.0 port
● Built-in networking to connect to 10Base-T/100Base-TX networks.
● To determine the ENERGY STAR® qualification status for this product see the Product
Data Sheet or Specifications Sheet.
2 Chapter 1 Product basics ENWW
Economical printing
Supplies
Accessibility
● Provides N-up printing (printing more than one page on a sheet).
● The printer driver provides the option to manually print on both sides.
● Uses print cartridges with HP ColorSphere toner.
● Online user guide is compatible with text screen-readers.
● Print cartridges can be installed and removed by using one hand.
● All doors and covers can be opened by using one hand.
ENWW Product features 3
Walkaround
Front and side view
3
4
5
1
2
6
7
8
9
Output bin (holds 125 sheets of standard paper)
Legal-output extension
Front door (provides access to the print cartridges)
Tray 1 (multipurpose tray)
Tray 2 (holds 250 sheets of standard paper and provides jam access)
Optional tray 3 (holds 250 sheets of standard paper)
Power switch
Control panel
DIMM door (for adding additional memory)
Back view
1 Hi-Speed USB 2.0 port and network port. (Network port present on HP Color LaserJet CP2020n, HP Color LaserJet
CP2020dn, and HP Color LaserJet CP2020x models only.)
4 Chapter 1 Product basics ENWW
2
3
Power connection
Rear door (for jam access)
Model and serial numbers
The model number and serial number are listed on an identification label located inside the front door.
The label contains information about the country/region of origin and the revision level, manufacturing date, production code, and production number of the product. The label also contains power rating and regulatory information.
P
S
Product of rodui t du
J er ial No
BR
21 apo n
CN
. CNBB
23
CN
P ro
123
47 du
47 ct
47 N o. Q
1234
56
394
8M
US
A
HE
ISE
W
, ID
LE
HIN
22
TT-
O 8
N B
Jan uar y 3,
H z, 2.5A
2007
LV
4
C
D
(2,5A
) ra
F
R
T his dia ha tio
p ro n p in m ay pte erf in ter
ca co te fe duc t c nd
, s rfe use re nce
u nd or on fo ub-c ha
T his d itio nce
rec es eiv ira
R egu ev ice
: (1
, a anc rm e s ta pte nd s w r J ble ith
N
c atio
(2) ed
, in
C rd
SITE:BO la
o
D
é tory om n is
d
T pli
su his d
R ra es tion
2
1
H
é
M ice in
w bje
m le ith ct to ay m entaire du
P
th um t 1 e be st a r B
5 of llo
m the ode
OIS é le
B-04 ev ic g in te rfe
n ot ca us cc ep
th w e h at in ar
F
C g tw C m o t a ny ful
05
-0
0
>PET<
ENWW Walkaround 5
6 Chapter 1 Product basics ENWW
2 Control panel
●
●
ENWW 7
Control-panel walkaround
The product has the following items on the control panel.
!
3
4
5
6
1
2
7
8
Control-panel display: The display provides information about the product. Use the menus on the display to establish product settings.
Back arrow ( ) button: Use this button for the following actions:
● Exit the control-panel menus.
● Scroll back to a previous menu in a submenu list.
● Scroll back to a previous menu item in a submenu list (without saving changes to the menu item).
Left arrow ( ) button: Use this button to navigate through the menus or to decrease a value that appears on the display.
OK button: Press the OK button for the following actions:
● Open the control-panel menus.
● Open a submenu displayed on the control-panel display.
● Select a menu item.
● Clear some errors.
● Begin a print job in response to a control-panel prompt (for example, when the message [OK] to print appears on the control-panel display).
Right arrow ( ) button: Use this button to navigate through the menus or to increase a value that appears on the display.
Cancel Job ( X ) button: Press this button to cancel a print job whenever the attention light is blinking or to exit the controlpanel menus.
Ready light (green): The Ready light is on when the product is ready to print. It blinks when the product is receiving print data.
Attention light (amber): The Attention light blinks when the product requires user attention.
8 Chapter 2 Control panel ENWW
Control-panel menus
Use the menus
1.
Press OK to open the menus.
2.
Press the Left arrow ( ) or Right arrow ( ) button to navigate through the listings.
3.
Press OK to select the appropriate option. An asterisk (*) appears next to the active selection.
4.
Press the Back arrow ( ) button to scroll back through the submenus.
5.
Press X to exit the menu without saving any changes.
The sections that follow describe the options for each of the main menus:
●
●
●
Network config. menu on page 15
●
ENWW Control-panel menus 9
Reports menu
Use the Reports menu to print reports that provide information about the product.
Menu item
Demo page
Menu structure
Config report
Supplies status
Network report
Usage page
PCL font list
PS font list
PCL6 font list
Color usage log
Service page
Diagnostics page
Description
Prints a color page that demonstrates print quality.
Prints a map of the control-panel-menu layout.
Prints a list of all the product settings. Includes network information when the product is connected to a network.
Prints the status for each print cartridge, including the following information:
● Approximate pages remaining
● Approximate percentage of cartridge life remaining for each color
● Part number
● Number of pages printed
Prints a list of all product network settings
Prints a page that lists PCL pages, PCL 6 pages, HP postscript level 3 emulation pages, pages that were jammed or mispicked in the product, monochrome (black and white) or color pages; and reports the page count
Prints a list of all the PCL fonts that are installed.
Prints a list of all the PostScript (PS) fonts that are installed
Prints a list of all the PCL6 fonts that are installed
Prints a report that shows the user name, application name, and color usage information on a job-by-job basis
Prints the service report
Prints the calibration and color diagnostics pages
10 Chapter 2 Control panel ENWW
System setup menu
Use this menu to establish basic product settings. The System setup menu has several sub-menus.
Each is described in the following table.
Menu item
Language
Paper setup
Sub-menu item
Def. paper size
Def. paper type
Tray 1
Sub-menu item
Letter
A4
Legal
A list of available media types appears.
Description
Select the language for the control-panel display messages and the product reports.
Select the size for printing internal reports or any print job that does not specify a size.
Select the media type for printing internal reports or any print job that does not specify a type.
Select the default size and type for tray 1 from the list of available sizes and types.
Tray 2
Tray 3
Paper out action
Paper size
Paper type
Paper size
Paper type
Paper size
Paper type
Wait forever
Override
Cancel
Select the default size and type for tray 2 from the list of available sizes and types.
Print quality Restrict color Enable color
Disable color
If optional tray 3 is installed, select the default size and type for tray 3 from the list of available sizes and types.
Select how the product should react when a print job requires a size or type that is not available or when a specified tray is empty.
Select Wait forever to make the product wait until you load the correct media and press OK . This is the default setting.
Select Override to print on a different size or type after a specified delay.
Select Cancel to automatically cancel the print job after a specified delay.
If you select either Override or Cancel, the control panel prompts you to specify the number of seconds to delay. Press the Right arrow ( ) button to increase the time, up to 3600 seconds. Press the
Left arrow ( ) button to decrease the time.
Select Enable color to allow the job to print in monochrome (black and white) or color depending on the job. This is the default setting.
Select Disable color to disable color printing. All jobs will print in monochrome
(black and white). Some internal pages will still print in color.
ENWW Control-panel menus 11
Menu item
Display contrast
12 Chapter 2 Control panel
Sub-menu item
Calibrate color
Cartridge low
Replace supplies
Color Supply Out
Adjust Alignment
Lightest
Sub-menu item
After power on
Calibrate now
(1-20)
Override out
Stop at out
Stop Printing (default)
Continue Black
Print Test Page
Adjust Tray <X>
Description
After power on: Select how soon the product should calibrate after you turn it on. The default setting is 15 minutes.
Calibrate now: Makes the product perform a calibration immediately. If a job is processing, the product calibrates after the job is complete. If an error message is displayed, you must clear the error first.
The percentage threshold determines when the product begins reporting low toner. The message is either reported on the control-panel display or using the toner LED, if it exists.
Override out: If the product determines that a print cartridge has reached the end of its estimated life, select this setting to continue printing. Using this option will eventually result in unacceptable print quality. Consider having a replacement cartridge available for when the print quality becomes unacceptable.
Stop at out: If the product determines that a print cartridge has reached the end of its estimated life, select this setting to stop printing. This is the default setting.
Printing beyond this point is possible using Override out. The supply does not need to be replaced now unless the print quality is no longer acceptable.
Information about the remaining toner is not available when printing in Override
out mode.
Once an HP supply has reached the end of its estimated life, HP's Premium
Protection Warranty on that supply has ended. For Warranty information, see
Print cartridge limited warranty statement on page 129 .
Stop Printing: If the product determines that a color cartridge has reached its estimated end of life, it stops printing.
This is the default setting.
Continue Black: If the product determines that a color cartridge has reached the end of its estimated life, continue printing using black only.
Print Test Page: Print a test page that tests printer alignment.
Adjust Tray <X>: Adjust the alignment of the specified tray.
Select the level of contrast for the display. The default setting is Medium.
ENWW
Menu item Sub-menu item
Lighter
Medium
Darker
Darkest
Sub-menu item Description
ENWW Control-panel menus 13
Service menu
Use this menu to restore default settings, clean the product, and activate special modes that affect print output.
Menu item
Cleaning mode
PowerSave
USB speed
Less paper curl
Archive print
Restore defaults
Sub-menu item
High
Full
Off
On
Off
On
Yes
No
Description
Use this option to clean the product if you see toner specks or other marks on the printed output. The cleaning process removes dust and excess toner from the paper path.
When you select this item, the product prompts you to load plain paper in tray 1 and then press OK to start the cleaning process. Wait until the process is complete. Discard the page that prints.
Sets how long the product remains idle before it enters
PowerSave mode. The product automatically exits
PowerSave mode when you send a print job or press a controlpanel button.
The default setting is 15 minutes.
Sets the USB speed to High or Full. For the product to actually operate at high speed, it must have high speed enabled and be connected to an EHCI host controller that is also operating at high speed. This menu item also does not reflect the current operating speed of the product.
The default setting is High.
If printed pages are consistently curled, use this option to set the product to a mode that reduces curl.
The default setting is Off.
If you are printing pages that will be stored for a long time, use this option to set the product to a mode that reduces toner smearing and dusting.
The default setting is Off.
Sets all customized settings to the factory default values.
14 Chapter 2 Control panel ENWW
Network config. menu
Use this menu to establish network configuration settings.
Menu item
TCP/IP config
Sub-menu item
Automatic
Manual
Auto crossover
Network services
Show IP address
Link speed
On
Off
IPv4
IPv6
DHCPv6
No
Yes
Automatic (default)
10T Full
10T Half
100TX Full
100TX Half
Description
Select Automatic to automatically configure all the
TCP/IP settings.
Select Manual to manually configure the IP address, subnet mask, and default gateway.
The default setting is Automatic.
This item is used when you are connecting the product directly to a personal computer using an
Ethernet cable (you might have to set this to On or
Off depending on the computer being used).
The default setting is On.
This item is used by the network administrator to limit the network services available on this product.
On
Off
The default setting for all items is On.
No: The product IP address will not appear on the control-panel display.
Yes: The product IP address will appear on the control-panel display, alternating between supplies information and the IP address of the device. The IP address will not be displayed if an error condition exits.
The default setting is No.
Sets the link speed manually if needed.
After setting the link speed, the product automatically restarts.
Restore defaults settings to the default values.
ENWW Control-panel menus 15
16 Chapter 2 Control panel ENWW
3 Software for Windows
●
Supported operating systems for Windows
●
Supported printer drivers for Windows
●
HP Universal Print Driver (UPD)
●
Select the correct printer driver for Windows
●
●
Change printer-driver settings for Windows
●
●
ENWW 17
Supported operating systems for Windows
The product supports the following Windows operating systems:
● Windows XP (32-bit and 64-bit)
● Windows Server 2003 (32-bit and 64-bit)
● Windows 2000
● Windows Vista
18 Chapter 3 Software for Windows ENWW
Supported printer drivers for Windows
● PCL 6
● HP postscript level 3 emulation
The printer drivers include online Help that has instructions for common printing tasks and also describes the buttons, checkboxes, and drop-down lists that are in the printer driver.
NOTE: The Postscript driver that supports this product is the Postscript version of the HP Universal
Print Driver (UPD) for Windows. It installs and operates in the same manner as previous versions of
Postscript drivers, and it does not require any special configuration. For more information about the
UPD, see www.hp.com/go/upd .
ENWW Supported printer drivers for Windows 19
HP Universal Print Driver (UPD)
The HP Universal Print Driver (UPD) for Windows is a single driver that gives you instant access to virtually any HP LaserJet product, from any location, without downloading separate drivers. It is built on proven HP print driver technology and has been tested thoroughly and used with many software programs. It is a powerful solution that performs consistently over time.
The HP UPD communicates directly with each HP product, gathers configuration information, and then customizes the user interface to show the product’s unique, available features. It automatically enables features that are available for the product, such as two-sided printing and stapling, so you do not need to enable them manually.
For more information, go to www.hp.com/go/upd .
UPD installation modes
Traditional mode
Dynamic mode
● Use this mode if you are installing the driver from a CD for a single computer.
● When installed with this mode, UPD operates like traditional printer drivers.
● If you use this mode, you must install UPD separately for each computer.
● Use this mode if you are installing the driver for a mobile computer, so you can discover and print to HP products in any location.
● Use this mode if you are installing UPD for a workgroup.
● To use this mode, download UPD from the Internet. See www.hp.com/go/ upd .
20 Chapter 3 Software for Windows ENWW
Select the correct printer driver for Windows
Printer drivers provide access to the product features and allow the computer to communicate with the product (using a printer language). Check the installation notes and readme files on the device CD for additional software and languages.
HP PCL 6 driver description
● Recommended for printing in all Windows environments
● Provides the overall best speed, print quality, and product-feature support for most users
● Developed to align with the Windows Graphic Device Interface (GDI) for the best speed in Windows environments
● Might not be fully compatible with third-party and custom software programs that are based on
PCL 5
HP Universal Print Driver for Windows - Postscript description
● Recommended for printing with Adobe ® software programs or with other highly graphics-intensive software programs
● Provides support for printing from Postscript needs
● Performs slightly faster than the PCL 6 driver when using Adobe software programs
ENWW Select the correct printer driver for Windows 21
Priority for print settings
Changes to print settings are prioritized depending on where the changes are made:
NOTE: The names of commands and dialog boxes might vary depending on your software program.
● Page Setup dialog box: Click Page Setup or a similar command on the File menu of the program you are working in to open this dialog box. Settings changed here override settings changed anywhere else.
● Print dialog box: Click Print, Print Setup, or a similar command on the File menu of the program you are working in to open this dialog box. Settings changed in the Print dialog box have a lower priority and do not override changes made in the Page Setup dialog box.
● Printer Properties dialog box (printer driver): Click Properties in the Print dialog box to open the printer driver. Settings changed in the Printer Properties dialog box do not override settings anywhere else in the printing software.
● Default printer driver settings: The default printer driver settings determine the settings used in all print jobs, unless settings are changed in the Page Setup, Print, or Printer Properties dialog boxes.
● Printer control panel settings: Settings changed at the printer control panel have a lower priority than changes made anywhere else.
22 Chapter 3 Software for Windows ENWW
Change printer-driver settings for Windows
Change the settings for all print jobs until the software program is closed
Change the default settings for all print jobs
1.
On the File menu in the software program, click Print.
2.
Select the driver, and then click
Properties or Preferences.
The steps can vary; this procedure is most common.
1.
Windows XP and Windows
Server 2003 (using the default
Start menu view): Click Start, and then click Printers and Faxes.
-or-
Change the product configuration settings
1.
Windows XP and Windows
Server 2003 (using the default
Start menu view): Click Start, and then click Printers and Faxes.
-or-
Windows 2000, Windows XP, and
Windows Server 2003 (using the
Classic Start menu view): Click
Start, click Settings, and then click
Printers.
-or-
Windows 2000, Windows XP, and
Windows Server 2003 (using the
Classic Start menu view): Click
Start, click Settings, and then click
Printers.
-or-
Windows Vista: Click Start, click
Control Panel, and then in the category for Hardware and
Sound click Printer.
Windows Vista: Click Start, click
Control Panel, and then in the category for Hardware and
Sound click Printer.
2.
Right-click the driver icon, and then select Printing Preferences.
2.
Right-click the driver icon, and then select Properties.
3.
Click the Device Settings tab.
ENWW Change printer-driver settings for Windows 23
Install the Windows software
Software installation types for Windows
You can choose from the following types of software installations:
● Recommended. Installs all of the software for the product, including the user guide. This can be selected for either direct connect (USB) or network installations.
● Express USB Install. Installs the minimum software for a product that uses a direct USB connection. Selecting this install method indicates your acceptance of HP's Software License terms.
● Express Network Install. Installs the minimum software for a product that is connected to a network. Selecting this install method indicates your acceptance of HP's Software License terms.
Remove software for Windows
1.
Click Start, and then click All Programs.
2.
Click HP, and then click HP Color LaserJet CP2020 Series Printer.
3.
Click Uninstall HP Color LaserJet CP2020 Series Printer, and then follow the onscreen instructions to remove the software.
24 Chapter 3 Software for Windows ENWW
Supported utilities
HP Web Jetadmin
HP Web Jetadmin is a browser-based management tool for HP Jetdirect-connected printers within your intranet, and it should be installed only on the network administrator’s computer.
To download a current version of HP Web Jetadmin and for the latest list of supported host systems, visit www.hp.com/go/webjetadmin .
When installed on a host server, a Windows client can gain access to HP Web Jetadmin by using a supported Web browser (such as Microsoft® Internet Explorer 4.x or Netscape Navigator 4.x or later) by navigating to the HP Web Jetadmin host.
Embedded Web server
The device is equipped with an embedded Web server, which provides access to information about device and network activities. This information appears in a Web browser, such as Microsoft Internet
Explorer, Netscape Navigator, Apple Safari, or Firefox.
The embedded Web server resides on the device. It is not loaded on a network server.
The embedded Web server provides an interface to the device that anyone who has a networkconnected computer and a standard Web browser can use. No special software is installed or configured, but you must have a supported Web browser on your computer. To gain access to the embedded Web server, type the IP address for the device in the address line of the browser. (To find the IP address, print a configuration page. For more information about printing a configuration page, see
Information pages on page 68 .)
For a complete explanation of the features and functionality of the embedded Web server, see
Embedded Web server on page 77 .
ENWW Supported utilities 25
HP ToolboxFX
HP ToolboxFX software is a program that you can use for the following tasks:
● Check the product status
● Check the supplies status and shop online for supplies
● Set up alerts
● View product usage reports
● View product documentation
● Gain access to troubleshooting and maintenance tools
HP ToolboxFX is supported for direct USB and network installations. You do not have to have Internet access to open and use HP ToolboxFX. HP ToolboxFX is only available following a Recommended install.
NOTE: HP ToolboxFX is not supported for Windows 2000, Windows Server 2003, or Macintosh operating systems. To use HP ToolboxFX, you must have TCP/IP protocol installed on your computer.
Supported operating systems ● Microsoft Windows XP, Service Pack 2 (Home and
Professional editions)
● Microsoft Windows Vista™
For more information about using HP ToolboxFX software, see
.
Other Windows components and utilities
● Software installer — automates the printing system installation
● Online Web registration
● Print Quality Optimizer Video
● HP Basic Color Match
● HP Easy Printer Care
● Web Printsmart
● HP Sure Supply
● HP Marketing Resource software
26 Chapter 3 Software for Windows ENWW
4 Use the product with Macintosh
●
●
Use features in the Macintosh printer driver
ENWW 27
Software for Macintosh
Supported operating systems for Macintosh
The device supports the following Macintosh operating systems:
● Mac OS X V10.2.8, V10.3, V10.4 and later
NOTE: For Mac OS V10.4 and later, PPC and Intel Core Processor Macs are supported.
Supported printer drivers for Macintosh
The HP installer provides PostScript ® Printer Description (PPD) files and Printer Dialog Extensions
(PDEs) for use with Macintosh computers.
The PPDs, in combination with the Apple PostScript printer drivers, provide access to device features.
Use the Apple PostScript printer driver that comes with the computer.
Priority for print settings for Macintosh
Changes to print settings are prioritized depending on where the changes are made:
NOTE: The names of commands and dialog boxes might vary depending on your software program.
● Page Setup dialog box: Click Page Setup or a similar command on the File menu of the program you are working in to open this dialog box. Settings changed here might override settings changed anywhere else.
● Print dialog box: Click Print, Print Setup, or a similar command on the File menu of the program you are working in to open this dialog box. Settings changed in the Print dialog box have a lower priority and do not override changes made in the Page Setup dialog box.
● Default printer driver settings: The default printer driver settings determine the settings used in all print jobs, unless settings are changed in the Page Setup, Print, or Printer Properties dialog boxes.
● Printer control panel settings: Settings changed at the printer control panel have a lower priority than changes made anywhere else.
Change printer-driver settings for Macintosh
Change the settings for all print jobs until the software program is closed
Change the default settings for all print jobs
1.
On the File menu, click Print.
2.
Change the settings that you want on the various menus.
1.
On the File menu, click Print.
2.
Change the settings that you want on the various menus.
Change the product configuration settings
Mac OS X V10.2.8
1.
In the Finder, on the Go menu, click
Applications.
3.
On the Presets menu, click Save
as and type a name for the preset.
2.
Open Utilities, and then open Print
Center.
These settings are saved in the
Presets menu. To use the new settings, you must select the saved preset option every time you open a program and print.
3.
Click on the print queue.
28 Chapter 4 Use the product with Macintosh ENWW
Change the settings for all print jobs until the software program is closed
Change the default settings for all print jobs
Change the product configuration settings
4.
On the Printers menu, click
Configure.
5.
Click the Installable Options menu.
NOTE: Configuration settings might not be available in Classic mode.
Mac OS X V10.3 or Mac OS X V10.4
1.
From the Apple menu, click System
Preferences and then Print &
Fax.
2.
Click Printer Setup.
3.
Click the Installable Options menu.
Mac OS X V10.5
1.
From the Apple menu, click System
Preferences and then Print &
Fax.
2.
Click Options & Supplies.
3.
Click the Driver menu.
4.
Select the driver from the list, and configure the installed options.
Supported utilities for Macintosh
View embedded Web server using a Macintosh
The HP embedded Web server (EWS) is accessed by clicking the Utility button when viewing the print queue. This opens a Web browser, such as Safari, which allows the user to access the EWS. The EWS can also be accessed directly by typing the network IP address or DNS name of the product into the
Web browser.
HP USB EWS Gateway software, which is automatically installed, also allows a Web browser to access the product if the product is connected using a USB cable. Click the Utility button when using a USB connection to access the EWS though the Web browser.
Use the EWS to perform the following tasks:
● View the device status and change device settings.
● View and change network settings for the device.
● Print information pages for the device.
● View the device event log.
ENWW Software for Macintosh 29
Use features in the Macintosh printer driver
Create and use printing presets in Macintosh
Use printing presets to save the current printer driver settings for reuse.
Create a printing preset
1.
On the File menu, click Print.
2.
Select the driver.
3.
Select the print settings.
4.
In the Presets box, click Save As..., and type a name for the preset.
5.
Click OK.
Use printing presets
1.
On the File menu, click Print.
2.
Select the driver.
3.
In the Presets box, select the printing preset that you want to use.
NOTE: To use printer-driver default settings, select Standard.
Resize documents or print on a custom paper size
You can scale a document to fit on a different size of paper.
1.
On the File menu, click Print.
2.
Open the Paper Handling menu.
3.
In the area for Destination Paper Size, select Scale to fit paper size, and then select the size from the drop-down list.
4.
If you want to use only paper that is smaller than the document, select Scale down only.
Print a cover page
You can print a separate cover page for your document that includes a message (such as “Confidential”).
1.
On the File menu, click Print.
2.
Select the driver.
3.
Open the Cover Page menu, and then select whether to print the cover page Before Document or After Document.
4.
In the Cover Page Type menu, select the message that you want to print on the cover page.
NOTE: To print a blank cover page, select Standard as the Cover Page Type.
30 Chapter 4 Use the product with Macintosh ENWW
Use watermarks
A watermark is a notice, such as “Confidential,” that is printed in the background of each page of a document.
1.
On the File menu, click Print.
2.
Open the Watermarks menu.
3.
Next to Mode, select the type of watermark to use. Select Watermark to print a semi-transparent message. Select Overlay to print a message that is not transparent.
4.
Next to Pages, select whether to print the watermark on all pages or on the first page only.
5.
Next to Text, select one of the standard messages, or select Custom and type a new message in the box.
6.
Select options for the remaining settings.
Print multiple pages on one sheet of paper in Macintosh
You can print more than one page on a single sheet of paper. This feature provides a cost-effective way to print draft pages.
1.
On the File menu, click Print.
2.
Select the driver.
3.
Open the Layout menu.
4.
Next to Pages per Sheet, select the number of pages that you want to print on each sheet (1, 2,
4, 6, 9, or 16).
5.
Next to Layout Direction, select the order and placement of the pages on the sheet.
6.
Next to Borders, select the type of border to print around each page on the sheet.
Print on both sides of the page (duplex printing)
CAUTION: To avoid jams, do not load paper that is heavier than 105 g/m 2 (28-lb bond).
ENWW Use features in the Macintosh printer driver 31
Use automatic duplex printing
1.
Insert enough paper into one of the trays to accommodate the print job. If you are loading special paper such as letterhead, load it in one of the following ways:
● For tray 1, load the letterhead paper face-up with the bottom edge feeding into the printer first.
● For all other trays, load the letterhead paper face-down with the top edge at the back of the tray.
2.
On the File menu, click Print.
3.
Open the Layout menu.
4.
Next to Two-Sided, select either Long-Edge Binding or Short-Edge Binding.
5.
Click Print.
Print on both sides manually
1.
Insert enough paper into one of the trays to accommodate the print job. If you are loading special paper such as letterhead, load it in one of the following ways:
● For tray 1, load the letterhead paper face-up with the bottom edge feeding into the printer first.
● For all other trays, load the letterhead paper face-down with the top edge at the back of the tray.
2.
On the File menu, click Print.
3.
On the Finishing menu, select Manually Print on 2nd Side.
4.
Click Print. Follow the instructions in the pop-up window that appears on the computer screen before replacing the output stack in tray 1 for printing the second half.
5.
Go to the printer, and remove any blank paper that is in tray 1.
6.
Insert the printed stack face-up with the bottom edge feeding into the printer first in tray 1. You
must print the second side from tray 1.
7.
If prompted, press the appropriate control-panel button to continue.
Set the color options
Use the Color Options pop-up menu to control how colors are interpreted and printed from software programs.
1.
Click Show Advanced Options.
2.
Adjust the individual settings for text, graphics, and photographs.
Use the Services menu
If the product is connected to a network, use the Services menu to obtain product and supply-status information.
1.
On the File menu, click Print.
2.
Open the Services menu.
32 Chapter 4 Use the product with Macintosh ENWW
5 Connectivity
●
Supported network operating systems
●
●
●
Configure the product on the network
ENWW 33
Supported network operating systems
The following operating systems support network printing:
Full software installation
● Windows 2003 Server (64-bit)
● Windows XP (32-bit and 64-bit)
● Windows Vista (32-bit and 64-bit)
● Mac OS X V10.2.8, V10.3, V10.4 and later
Printer driver only
● Windows 2000
● Windows 2003 Server (32-bit)
● Linux (Web only)
● UNIX model scripts (Web only)
Printer sharing disclaimer
HP does not support peer-to-peer networking, as the feature is a function of Microsoft operating systems and not of the HP printer drivers. Go to Microsoft at www.microsoft.com
.
34 Chapter 5 Connectivity ENWW
USB connection
NOTE: Do not connect the USB cable before installing the software. The installation program will notify you when the USB cable should be connected.
This product supports a USB 2.0 connection. You must use an A-to-B type USB cable for printing.
ENWW USB connection 35
Supported network protocols
The product supports the TCP/IP network protocol. It is the most widely used and accepted networking protocol. Many networking services utilize this protocol. This product also supports IPv4 and IPv6. The following tables list the networking services/protocols that are supported on the product.
Table 5-1 Printing
Service name Description port9100 (Direct Mode)
Line printer daemon (LPD) ws-print
Printing service
Printing service
Microsoft plug-and-play printing solution
Table 5-2 Network product discovery
Service name
SLP (Service Location Protocol) mDNS (multicast Domain Name Service - also known as
“Rendezvous” or “Bonjour”) ws-discover
Description
Device Discovery Protocol, used to help find and configure network devices. Used primarily by Microsoft-based software programs.
Device Discovery Protocol, used to help find and configure network devices. Used primarily by Apple Macintosh-based software programs.
Used by Microsoft-based software programs
Table 5-3 Messaging and management
Service name
HTTP (hypertext transfer protocol)
EWS (embedded Web server)
SNMP (simple network management protocol)
Description
Allows Web browsers to communicate with embedded Web server.
Allows a user to manage the product through a Web browser.
Used by network programs for product management. SNMP
V1 and standard MIB-II (Management Information Base) objects are supported.
Table 5-4 IP addressing
Service name Description
DHCP (dynamic host configuration protocol), IPv4, and IPv6 For Automatic IP address assignment. DHCP server provides the product with an IP address. Generally requires no user intervention for product to obtain IP address from a DHCP server.
36 Chapter 5 Connectivity ENWW
Table 5-4 IP addressing (continued)
Service name
BOOTP (bootstrap protocol)
Auto IP
Description
For Automatic IP address assignment. BOOTP server provides the product with an IP address. Requires administrator to input the product MAC hardware address on
BOOTP server in order for product to obtain an IP address from that server.
For Automatic IP address assignment. If neither a DHCP server nor a BOOTP server is present, this service allows the product to generate a unique IP address.
ENWW Supported network protocols 37
Configure the product on the network
To configure network parameters on the product, use the product control panel, or the embedded Web server. For Windows operating systems, use the HP ToolboxFX software. For Mac OS X, use the
Utility button.
Set up the product on the network
Hewlett-Packard recommends that you use the HP software installer on the product CD-ROM to set up printer drivers for networks.
NOTE: You must connect the printer to your network prior to starting the software installation.
This product supports a 10/100 network connection. Plug the network cable into the product and your network connection.
View settings
Network configuration page
The network configuration page lists the current settings and properties of the product network card. To print the network configuration page from the product, complete the following steps.
1.
On the control panel, press OK .
2.
Use the arrow buttons to select Reports, and then press OK .
3.
Use the arrow buttons to select Network report, and then press OK .
Configuration page
The configuration page lists the current settings and properties of the product. To print the configuration page from the product, complete the following steps.
1.
On the control panel, press OK .
2.
Use the arrow buttons to select Reports, and then press OK .
3.
Use the arrow buttons to select Config report, and then press OK .
38 Chapter 5 Connectivity ENWW
IP address
You can configure the IP address manually or automatically via DHCP, BootP, or AutoP.
Manual configuration
1.
On the control-panel menu, press OK .
2.
Use the Left arrow ( ) or the Right arrow ( ) button to select Network config., and then press
OK .
3.
Use the Left arrow ( ) or the Right arrow ( ) button to select TCP/IP config, and then press
OK .
4.
Use the Left arrow ( ) or the Right arrow ( ) button to select Manual, and then press OK .
5.
Press the Right arrow ( ) button to increase the value for the first section of the IP address. Press the Left arrow ( ) button to decrease the value. When the value is correct, press OK . Repeat this process for the other three sections of the IP address.
6.
If the address is correct, use the Left arrow ( ) or the Right arrow ( ) button to select Yes, and then press OK . Repeat step 5 for the subnet mask and default gateway settings.
-or-
If the IP address is incorrect, use the Left arrow ( ) or the Right arrow ( ) button to select No, and then press OK . Repeat step 5 to establish the correct IP address, and then repeat step 5 for the subnet mask and default gateway settings.
Automatic configuration
NOTE: Automatic is the default Network config. TCP/IP config setting.
1.
On the control-panel menu, press OK .
2.
Use the Left arrow ( ) or the Right arrow ( ) button to select Network config., and then press
OK .
3.
Use the Left arrow ( ) or the Right arrow ( ) button to select TCP/IP config, and then press
OK .
4.
Use the Left arrow ( ) or the Right arrow ( ) button to select Automatic, and then press OK .
It might take several minutes before the automatic IP address is ready for use.
NOTE: To disable or enable specific automatic IP modes (such as BOOTP, DHCP, or AutoIP), use the embedded Web server or HP ToolboxFX.
ENWW Configure the product on the network 39
Show or hide the IP address on the control panel
NOTE: When Show IP address is On, the IP address will alternately appear on the control-panel display with the print-cartridge-status gauges.
1.
On the control-panel menu, press OK .
2.
Use the Left arrow ( ) or the Right arrow ( ) button to select Network config., and then press
OK .
3.
Use the Left arrow ( ) or the Right arrow ( ) button to select Show IP address, and then press
OK .
4.
Use the Left arrow ( ) or the Right arrow ( ) button to select Yes or No, and then press OK .
Set automatic crossover
1.
On the control-panel menu, press OK .
2.
Use the Left arrow ( ) or the Right arrow ( ) button to select Network config., and then press
OK .
3.
Use the Left arrow ( ) or the Right arrow ( ) button to select Automatic crossover, and then press OK .
4.
Use the Left arrow ( ) or the Right arrow ( ) button to select On or Off, and then press OK .
Set network services
1.
On the control-panel menu, press OK .
2.
Use the Left arrow ( ) or the Right arrow ( ) button to select Network config., and then press
OK .
3.
Use the Left arrow ( ) or the Right arrow ( ) button to select Network services, and then press
OK .
4.
Use the Left arrow ( ) or the Right arrow ( ) button to select IPv4 or IPv6, and then press OK .
5.
Use the Left arrow ( ) or the Right arrow ( ) button to select On or Off, and then press OK .
40 Chapter 5 Connectivity ENWW
Restore defaults (network settings)
1.
On the control-panel menu, press OK .
2.
Use the Left arrow ( ) or the Right arrow ( ) button to select Network config., and then press
OK .
3.
Use the Left arrow ( ) or the Right arrow ( ) button to select Restore defaults, and then press
OK .
4.
Press OK to restore the factory network default settings. Press X to exit the menu without restoring the factory network default settings.
TCP/IP
Similar to a common language that people use to communicate with each other, TCP/IP (Transmission
Control Protocol/Internet Protocol) is a suite of protocols designed to define the way computers and other devices communicate with each other over a network.
IP address
Every host (workstation or node) on an IP network requires a unique IP address for each network interface. This address is a software address that is used to identify both the network and specific hosts that are located on that network. It is possible for a host to query a server for a dynamic IP address each time the device boots up (for example, using DHCP and BOOTP).
An IPv4 address contains four bytes of information, divided into sections that each contain one byte.
The IP address has the following format: xxx.xxx.xxx.xxx
NOTE: When assigning IP addresses, always consult the IP address administrator. Setting the wrong address can disable other equipment operating on the network or interfere with communications.
Configure IP parameters
IP configuration parameters can be configured manually, or they can be automatically downloaded by using DHCP or BOOTP each time the product is turned on.
When turned on, a new product that is unable to retrieve a valid IP address from the network automatically assigns itself a default IP address. On a small private network, a unique IP address in the range of 169.254.1.0 to 169.254.254.255 is assigned. The IP address for the product is listed on the product Configuration page and the Network report. See
.
Dynamic Host Configuration Protocol (DHCP)
DHCP allows a group of devices to use a set of IP addresses that are maintained by a DHCP server.
The device sends a request to the server, and if an IP address is available, the server assigns it to that device.
BOOTP
BOOTP is a bootstrap protocol used to download configuration parameters and host information from a network server.
The client broadcasts a boot request packet that contains the product hardware address. The server answers with a boot reply packet that contains the information that the device needs for configuration.
ENWW Configure the product on the network 41
Subnets
When an IP network address for a particular network class is assigned to an organization, no provision is made for more than one network being present at that location. Local network administrators use subnets to partition a network into several different subnetworks. Splitting a network into subnets can result in better performance and improved use of limited network address space.
Subnet mask
The subnet mask is a mechanism used to divide a single IP network into several different subnetworks.
For a given network class, a portion of an IP address that would normally be used to identify a node is used, instead, to identify a subnetwork. A subnet mask is applied to each IP address to specify the portion used for subnetworks, and the portion used to identify the node.
Gateways
Gateways (routers) are used to connect networks together. Gateways are devices that act as translators between systems that do not use the same communication protocols, data formatting, structures, languages, or architectures. Gateways repackage the data packets and change the syntax to match that of the destination system. When networks are divided into subnets, gateways are required to connect one subnet to another.
Default gateway
The default gateway is the IP address of the gateway or router that moves packets between networks.
If multiple gateways or routers exist, then the default gateway is typically the address of the first, or nearest, gateway or router. If no gateways or routers exist, then the default gateway will typically assume the IP address of the network node (such as the workstation or product).
42 Chapter 5 Connectivity ENWW
6 Paper and print media
●
Understand paper and print media use
●
Supported paper and print media sizes
●
Supported paper types and tray capacity
●
Special paper or print media guidelines
●
ENWW 43
Understand paper and print media use
This product supports a variety of paper and other print media in accordance with the guidelines in this user guide. Paper or print media that does not meet these guidelines might cause the following problems:
● Poor print quality
● Increased jams
● Premature wear on the product, requiring repair
For best results, use only HP-brand paper and print media designed for laser printers or multiuse. Do not use paper or print media made for inkjet printers. Hewlett-Packard Company cannot recommend the use of other brands of media because HP cannot control their quality.
It is possible for paper to meet all of the guidelines in this user guide and still not produce satisfactory results. This might be the result of improper handling, unacceptable temperature and/or humidity levels, or other variables over which Hewlett-Packard has no control.
CAUTION: Using paper or print media that does not meet Hewlett-Packard's specifications might cause problems for the product, requiring repair. This repair is not covered by the Hewlett-Packard warranty or service agreements.
44 Chapter 6 Paper and print media ENWW
Supported paper and print media sizes
This product supports a number of paper sizes, and it adapts to various media.
NOTE: To obtain best print results, select the appropriate paper size and type in your print driver before printing.
Table 6-1 Supported paper and print media sizes
Size Dimensions Tray 1 Tray 2 or optional tray
3
Letter 216 x 279 mm (8.5 x 11 inches)
Legal 216 x 356 mm (8.5 x 14 inches)
A4
Executive
A3
A5
A6
B4 (JIS)
B5 (JIS)
B5 (ISO)
B6 (ISO)
16k
8.5 x 13
4 x 6
5 x 8
10 x 15 cm
Custom
Custom
210 x 297 mm (8.27 x 11.69 inches)
184 x 267 mm (7.24 x 10.51 inches)
297 x 420 mm (11.69 x 16.54 inches)
148 x 210 mm (5.83 x 8.27 inches)
105 x 148 mm (4.13 x 5.83 inches)
257 x 364 mm (10.12 x 14.33 inches)
182 x 257 mm (7.17 x 10.12 inches)
176 x 250 mm (6.93 x 9.84 inches)
125 x 176 mm (4.92 x 6.93 inches)
184 x 260 mm (7.24 x 10.23 inches)
195 x 270 mm (7.68 x 10.62 inches)
197 x 273 mm (7.75 x 10.75 inches)
216 x 330 mm (8.5 x 13 inches)
107 x 152 mm (4 x 6 inches)
127 x 203 mm (5 x 8 inches)
100 x 150 mm (3.9 x 5.9 inches)
(76 - 216) x (127 - 356) mm ((3 - 8.5) x (5 - 14) inches)
(102 - 216) x (153 - 356) mm ((4 - 8.5) x (6 - 14) inches)
Table 6-2 Supported envelopes and postcards
Size Dimensions
Envelope #10 105 x 241 mm (4.13 x 9.49 inches)
Tray 1 Tray 2
ENWW Supported paper and print media sizes 45
Table 6-2 Supported envelopes and postcards (continued)
Size Dimensions
Envelope DL 110 x 220 mm (4.33 x 8.66 inches)
Envelope C5
Envelope B5
162 x 229 mm (6.93 x 9.84 inches)
176 x 250 mm (6.7 x 9.8 inches)
Envelope
Monarch
Postcard
98 x 191 mm (3.9 x 7.5 inches)
100 x 148 mm (3.94 x 5.83 inches)
Double postcard 148 x 200 mm (5.83 x 7.87 inches)
Tray 1 Tray 2
46 Chapter 6 Paper and print media ENWW
Supported paper types and tray capacity
Table 6-3 Tray 1
Media type Weight Capacity
Paper orientation
Every day:
● Plain
● Light
● Bond
60 to 90 g/m 2 (16 to 24 lb)
● Recycled
Presentation:
● Matte paper, mid-weight to heavy
● Glossy paper, mid-weight to heavy
Up to 176 g/m 2 (47 lb)
Brochure:
● Matte paper, mid-weight to heavy
Up to 176 g/m 2 (47 lb)
● Glossy paper, mid-weight to heavy
Photo/cover Up to 176 g/m 2 (47 lb)
● Matte cover paper
Up to 50 sheets
Up to 5 mm (0.2 inches) stack height
Up to 5 mm (0.2 inches) stack height
Side to be printed on face-up, with the top edge at the back of the tray
Side to be printed on face-up, with the top edge at the back of the tray
Side to be printed on face-up, with the top edge at the back of the tray
Up to 5 mm (0.2 inches) stack height
Side to be printed on face-up, with the top edge at the back of the tray
● Glossy cover paper
● Matte photo paper
● Glossy photo paper
● Cardstock
Other:
● Color laser transparency
● Labels
● Letterhead, envelope
● Heavy envelope
● Preprinted
● Prepunched
● Colored
Up to 50 sheets, or 10 envelopes Side to be printed on face-up, with the top edge at the back of the tray or the stamp-end at the back of the tray
● Rough
● Tough
1
2
Capacity can vary depending on media weight and thickness, and environmental conditions.
The device supports up to 220 g/m 2 (59 lb) for glossy and glossy photo paper.
ENWW Supported paper types and tray capacity 47
Table 6-4 Tray 2 and Tray 3
Media type Weight
Paper orientation
Every day:
● Plain
● Light
● Bond
● Recycled
Presentation:
● Matte paper, mid-weight to heavy
60 to 90 g/m 2 (16 to 24 lb)
Up to 176 g/m 2 (47 lb)
Up to 250 sheets
Up to 12.5 mm (0.5 inches) stack height
Side to be printed on face-up, with the top edge at the back of the tray
Side to be printed on face-up, with the top edge at the back of the tray
● Glossy paper, mid-weight to heavy
Brochure: Up to 176 g/m 2 (47 lb)
● Matte paper, mid-weight to heavy
● Glossy paper, mid-weight to heavy
Photo/cover Up to 176 g/m 2 (47 lb)
Up to 12.5 mm (0.5 inches) stack height
Side to be printed on face-up, with the top edge at the back of the tray
● Matte cover paper
● Glossy cover paper
● Matte photo paper
● Glossy photo paper
● Cardstock
Other:
● Color laser transparency
Up to 12.5 mm (0.5 inches) stack height
Side to be printed on face-up, with the top edge at the back of the tray
Up to 50 sheets, or 10 envelopes Side to be printed on face-up, with the top edge at the back of the tray or the stamp-end at the back of the tray
● Labels
● Letterhead, envelope
● Heavy envelope
● Preprinted
● Prepunched
● Colored
● Rough
● Tough
1
2
Capacity can vary depending on media weight and thickness, and environmental conditions.
The device supports up to 220 g/m 2 (59 lb) for glossy and glossy photo paper.
48 Chapter 6 Paper and print media ENWW
Special paper or print media guidelines
This product supports printing on special media. Use the following guidelines to obtain satisfactory results. When using special paper or print media, be sure to set the type and size in your print driver to obtain the best print results.
CAUTION: HP LaserJet printers use fusers to bond dry toner particles to the paper in very precise dots. HP laser paper is designed to withstand this extreme heat. Using inkjet paper not designed for this technology could damage your printer.
Media type
Envelopes
Labels
Transparencies
Letterhead or preprinted forms
Heavy paper
Glossy or coated paper
Do Do not
● Store envelopes flat.
● Use envelopes where the seam extends all the way to the corner of the envelope.
● Use peel-off adhesive strips that are approved for use in laser printers.
● Do not use envelopes that are wrinkled, nicked, stuck together, or otherwise damaged.
●
●
Do not use envelopes that have clasps, snaps, windows, or coated linings.
Do not use self-stick adhesives or other synthetic materials.
● Use only labels that have no exposed backing between them.
● Use Labels that lie flat.
●
●
Do not use labels that have wrinkles or bubbles, or are damaged.
Do not print partial sheets of labels.
● Use only full sheets of labels.
● Use only transparencies that are approved for use in laser printers.
● Place transparencies on a flat surface after removing them from the product.
● Do not use transparent print media not approved for laser printers.
● Use only letterhead or forms approved for use in laser printers.
● Use only glossy or coated paper that is approved for use in laser printers.
● Do not use raised or metallic letterhead.
● Use only heavy paper that is approved for use in laser printers and meets the weight specifications for this product.
● Do not use paper that is heavier than the recommended media specification for this product unless it is HP paper that has been approved for use in this product.
● Do not use glossy or coated paper designed for use in inkjet products.
ENWW Special paper or print media guidelines 49
Load paper and print media
Load tray 1
1.
Open tray 1.
2.
If loading long sheets of media, pull out the extension tray.
3.
If necessary, flip out the extension.
50 Chapter 6 Paper and print media ENWW
4.
Extend the paper guides fully (callout 1) and then load the media stack into tray 1 (callout 2). Adjust the paper guides to the size of the paper.
NOTE: Place the media into tray 1 with the side to be printed on face-up and the top toward the product.
Load tray 2 or 3
1.
Pull the tray out of the product.
2.
Slide open the paper length and width guides.
● To load Legal-size paper, extend the tray by pressing and holding the extension tab while pulling the front of the tray toward you.
ENWW
NOTE: When it is loaded with Legal-size paper, the tray extends from the front of the product approximately 64 mm (2.5 inches).
Load paper and print media 51
3.
Place the paper in the tray and make sure that it is flat at all four corners. Slide the paper length and width guides so that they are against the stack of paper.
4.
Push down on the paper to make sure that the paper stack is below the paper limit tabs on the side of the tray.
5.
Slide the tray into the product.
52 Chapter 6 Paper and print media ENWW
7 Print tasks
●
●
Use features in the Windows printer driver
ENWW 53
Cancel a print job
You can stop a print request by using the product control panel or using your software program. For instructions on how to stop a print request from a computer on a network, see the online Help for the specific network software.
NOTE: It can take some time for all printing to clear after you have canceled a print job.
Cancel the current print job at the product control panel
Press the Cancel Job ( X ) button on the control panel.
NOTE: If the print job has proceeded too far, you might not have the option to cancel it.
Cancel the current print job from the software program
A dialog box might appear briefly on the screen, giving you the option to cancel the print job.
If several requests have been sent to the product through your software, they might be waiting in a print queue (for example, in Windows Print Manager). See the software documentation for specific instructions about canceling a print request from the computer.
If a print job is waiting in a print queue (computer memory) or print spooler (Windows 2000, XP, or Vista), delete the print job there.
For Windows 2000, Windows XP, or Windows Vista, click Start and then click Printers and Faxes; or click Start, click Control Panel, and then click Printers and Faxes. Double-click the printer icon to open the print spooler. Select the print job that you want to cancel, and then press Cancel or Delete under the Document menu. If the print job is not canceled, you might need to shut down and restart the computer.
54 Chapter 7 Print tasks ENWW
Use features in the Windows printer driver
Open the printer driver
How do I
Open the printer driver
Get help for any printing option
Steps to perform
On the File menu in the software program, click Print. Select the printer, and then click Properties or Preferences.
Click the ? symbol in the upper-right corner of the printer driver, and then click any item in the printer driver. A pop-up message displays that provides information about the item. Or, click
Help to open the online Help.
Use printing shortcuts
To perform the following tasks, open the printer driver and click the Printing Shortcuts tab.
NOTE: In previous HP printer drivers, this feature was called Quick Sets.
How do I
Use a printing shortcut
Create a custom printing shortcut
Steps to perform
Select one of the shortcuts, and then click OK to print the job with the predefined settings.
a) Select an existing shortcut as a base. b) Select the print options for the new shortcut. c) Click Save As, type a name for the shortcut, and click OK.
Set paper and quality options
To perform the following tasks, open the printer driver and click the Paper/Quality tab.
How do I
Select a page size
Select a custom page size
Select a paper source
Select a paper type
Print covers on different paper
Print the first or last page on different paper
Steps to perform
Select a size from the Paper size drop-down list.
a) Click Custom. The Custom Paper Size dialog box opens.
b) Type a name for the custom size, specify the dimensions, and click OK.
Select a tray from the Paper source drop-down list.
Select a type from the Paper type drop-down list.
a) In the Special pages area, click Covers or Print pages on
different paper, and then click Settings. b) Select an option to print a blank or preprinted front cover, back cover, or both.
Or, select an option to print the first or last page on different paper. c) Select options from the Paper source and Paper
type drop-down lists, and then click Add. d) Click OK.
Set document effects
To perform the following tasks, open the printer driver and click the Effects tab.
ENWW Use features in the Windows printer driver 55
How do I
Scale a page to fit on a selected paper size
Scale a page to be a percent of the actual size
Print a watermark
Add or edit watermarks
NOTE: The printer driver must be stored on your computer for this to work.
Steps to perform
Click Print document on, and then select a size from the dropdown list.
Click % of actual size, and then type the percent or adjust the slider bar.
a) Select a watermark from the Watermarks drop-down list.
b) To print the watermark on the first page only, click First page
only. Otherwise, the watermark is printed on each page.
a) In the Watermarks area, click Edit. The Watermark
Details dialog box opens. b) Specify the settings for the watermark, and then click OK.
Set document finishing options
To perform the following tasks, open the printer driver and click the Finishing tab.
How do I
Print on both sides (Duplex)
Print a booklet
Print multiple pages per sheet
Select page orientation
Steps to perform
Click Print on both sides. If you will bind the document along the top edge, click Flip pages up.
a) Click Print on both sides. b) In the Booklet layout dropdown list, click Left binding or Right binding. The Pages per
sheet option automatically changes to 2 pages per sheet.
a) Select the number of pages per sheet from the Pages per
sheet drop-down list. b) Select the correct options for Print
page borders, Page order, and Orientation.
a) In the Orientation area, click Portrait or Landscape. b) To print the page image upside down, click Rotate by 180
degrees.
Obtain support and product-status information
To perform the following tasks, open the printer driver and click the Services tab.
How do I Steps to perform
Obtain support information for the product and order supplies online
In the Internet Services drop-down list, select a support option, and click Go!
Check the status of the product, including the level of supplies Click the Device and Supplies Status icon. The Device
Status page of the HP embedded Web server opens.
Set advanced printing options
To perform the following tasks, open the printer driver and click the Advanced tab.
56 Chapter 7 Print tasks ENWW
How do I Steps to perform
Select advanced printing options
Change the number of copies that are printed
NOTE: If the software program that you are using does not provide a way to print a particular number of copies, you can change the number of copies in the driver.
In any of the sections, click a current setting to activate a dropdown list so you can change the setting.
Open the Paper/Output section, and then enter the number of copies to print. If you select 2 or more copies, you can select the option to collate the pages.
Changing this setting affects the number of copies for all print jobs. After your job has printed, restore this setting to the original value.
Print colored text as black rather than as shades of gray
Load letterhead or preprinted paper the same way for every job, whether printing on one or both sides of the page a) Open the Document Options section, and then open the
Printer Features section. b) In the Print All Text as Black drop-down list, select Enabled.
a) Open the Document Options section, and then open the
Printer Features section. b) In the Alternative Letterhead
Mode drop-down list, select On. c) At the product, load the paper the same way you would for printing on both sides.
Change the order in which pages are printed a) Open the Document Options section, and then open the
Layout Options section. b) In the Page Order drop-down list, select Front to Back to print the pages in the same order as they are in the document, or select Back to Front to print the pages in the reverse order.
ENWW Use features in the Windows printer driver 57
58 Chapter 7 Print tasks ENWW
8 Color for Windows
●
●
●
ENWW 59
Manage color
Manage color by changing the settings on the Color tab in the printer driver.
Automatic
Setting color options to Automatic typically produces the best possible print quality for color documents.
The Automatic color adjustment option optimizes the neutral-gray color treatment, halftones, and edge enhancements for each element in a document. For more information, see your printer driver online
Help.
NOTE: Automatic is the default setting and is recommended for printing all color documents.
Print in Grayscale
Select the Print in Grayscale option from the printer driver to print a color document in black and white.
This option is useful for printing color documents that will be photocopied or faxed.
When Print in Grayscale is selected, the product uses the monochrome mode, which reduces use of the color cartridges.
Manual color adjustment
Use the Manual color adjustment option to adjust the neutral-gray color treatment, halftones, and edge enhancements for text, graphics, and photographs. To gain access to the manual color options, from the Color tab, select Manual, and then select Settings.
Manual color options
Use manual color options to adjust the Neutral Grays, Halftone, and Edge Control options for text, graphics, and photographs.
Table 8-1 Manual color options
Setting description Setting options
Halftone
Halftone options affect the color output resolution and clarity.
● Smooth provides better results for large, solid-filled print areas and enhances photographs by smoothing color gradations. Select this option when uniform and smooth area fills are the top priority.
● Detail is useful for text and graphics that require sharp distinctions among lines or colors, or images that contain a pattern or a high level of detail. Select this option when sharp edges and details are the top priority.
60 Chapter 8 Color for Windows ENWW
Table 8-1 Manual color options (continued)
Setting description Setting options
Neutral Grays
The Neutral Grays setting determines the method for creating gray colors used in text, graphics, and photographs.
● Black Only generates neutral colors (grays and black) by using only black toner. This guarantees neutral colors without a color cast. This setting is best for documents and grayscale viewgraphs.
● 4-Color generates neutral colors (grays and black) by combining all four toner colors. This method produces smoother gradients and transitions to other colors, and it produces the darkest black.
Edge Control ● Maximum is the most aggressive trapping setting. Adaptive halftoning is on.
The Edge Control setting determines how edges are rendered. Edge control has two components: adaptive halftoning and trapping. Adaptive halftoning increases edge sharpness. Trapping reduces the effect of color-plane misregistration by overlapping the edges of adjacent objects slightly.
● Normal sets trapping at a medium level. Adaptive halftoning is on.
● Light sets trapping at a minimal level, Adaptive halftoning is on.
● Off turns off both trapping and adaptive halftoning.
Color themes
Use color themes to adjust the RGB Color options for the entire page.
Setting description
RGB Color
Setting options
● Default (sRGB) instructs the product to interpret RGB color as sRGB. The sRGB standard is the accepted standard of Microsoft and the World Wide Web Consortium ( http://www.w3.org
).
● Vivid instructs the product to increase the color saturation in the midtones. Less colorful objects are rendered more colorfully. This setting is recommended for printing business graphics.
● Photo interprets RGB color as if it were printed as a photograph using a digital mini-lab. It renders deeper, more saturated colors differently than Default (sRGB) mode. Use this setting for printing photos.
● Photo (AdobeRGB 1998) is for digital photos that use the
AdobeRGB color space rather than sRGB. When printing from a professional software program that uses AdobeRGB, it is important to turn off the color management in the software program and allow the product to manage the color space.
● None sets the printer to print RGB data in raw device mode. To render photographs correctly when this option is selected, you must manage color in the program in which you are working or in the operating system.
ENWW Manage color 61
Match colors
For most users, the best method for matching colors is to print sRGB colors.
The process of matching printer output color to your computer screen is complex, because printers and computer monitors use different methods of producing color. Monitors display colors by using light pixels that use an RGB (red, green, blue) color process, but printers print colors by using a CMYK (cyan, magenta, yellow, and black) process.
Several factors can influence your ability to match printed colors to those on your monitor:
● Print media
● Printer colorants (inks or toners, for example)
● Printing process (inkjet, press, or laser technology, for example)
● Overhead lighting
● Personal differences in perception of color
● Software programs
● Printer drivers
● Computer operating systems
● Monitors
● Video cards and drivers
● Operating environment (humidity, for example)
Keep these factors in mind when colors on your screen do not perfectly match your printed colors.
Match colors using the Microsoft Office Basic Colors palette
You can use HP ToolboxFX to print a palette of the Microsoft Office Basic Colors. Use this palette to select the colors that you want to use in printed documents. It shows the actual colors that print when you select these basic colors in a Microsoft Office program.
1.
In HP ToolboxFX, select the Help folder.
2.
In the Color Printing Tools section, select Print Basic Colors.
3.
Adjust color in your document to match the color selection on the printed color palette.
Match colors using the HP Basic Color Match tool
The HP Basic Color Match tool allows you to adjust spot color in your printed output. For example, you can match the color of your company logo on your printed output. You can save and use the new color schemes for specific documents or all printed documents, or you can create multiple color schemes that you can choose from later.
This software tool is available to all users of this product. Before you can use the tool, you must download it from the Web through HP ToolboxFX or the software CD that came with your product.
62 Chapter 8 Color for Windows ENWW
Use the following procedure to download the HP Basic Color Match tool through the software CD.
1.
Insert the CD into your CD-ROM drive. The CD autoruns.
2.
Select Install more software.
3.
Select HP Basic Color Match. The tool downloads and installs itself. A desktop icon is also created.
Use the following procedure to download the HP Basic Color Match tool through HP ToolboxFX.
1.
Open HP ToolboxFX.
2.
Select the Help folder.
3.
In the Color Printing Tools section, select Basic Color Match. The tool downloads and installs itself. A desktop icon is also created.
After the HP Basic Color Match tool is downloaded and installed, it can be run from the desktop icon or from HP ToolboxFX (click the Help folder, and then Color Printing Tools, and then Basic Color
Match). The tool guides you through selecting colors. All color matches selected are saved as a color theme and can be accessed in the future.
Match colors using View Custom Colors
You can use HP ToolboxFX to print a palette of custom colors. In the Toolbox Color Printing Tools section, click View Custom Colors. Tab to the color page desired and print the current page. In your document, type the red, green, and blue values in the software's custom color menu to change them to match the color on the palette.
ENWW Match colors 63
Advanced color use
The product provides automatic color features that generate excellent color results. Carefully designed and tested color tables provide smooth, accurate color rendition of all printable colors.
The product also provides sophisticated tools for the experienced professional.
HP ColorSphere toner
HP designs the print system (printer, print cartridges, toner, and paper) to work together to optimize print quality, product reliability, and user productivity. Original HP print cartridges contain HP ColorSphere toner that is specifically matched to your printer so that it will produce a wide range of brilliant colors.
This helps you create professional looking documents that contain sharp, clear text and graphics and realistic printed photos.
HP ColorSphere toner produces print-quality consistency and intensity you can depend on across a wide range of papers That means you can produce documents that help you make the right impression.
Plus, HP professional-quality everyday and specialty papers (including a wide variety of HP media types and weights) are designed for the way you work.
HP ImageREt 3600
ImageREt 3600 provides 3600 dots-per-inch (dpi) color laser-class quality through a multi-level printing process. This process precisely controls color by combining up to four colors within a single dot and by varying the amount of toner in a given area. ImageREt 3600 has been improved for this product. The improvements offer trapping technologies, greater control over dot placement, and more precise control of toner quality in a dot. These new technologies, coupled with HP's multi-level printing process, result in a 600 x 600 dpi printer that provides 3600-dpi color laser-class quality with millions of smooth colors.
Media selection
For the best color and image quality, select the appropriate media type from the software printer menu or from the printer driver.
Color options
Color options automatically provide optimal color output. These options use object tagging, which provides optimal color and halftone settings for different objects (text, graphics, and photos) on a page.
The printer driver determines which objects appear on a page and uses halftone and color settings that provide the best print quality for each object.
In the Windows environment, the Automatic and Manual color options are on the Color tab in the printer driver.
Standard red-green-blue (sRGB)
Standard red-green-blue (sRGB) is a worldwide color standard that HP and Microsoft developed as a common color language for monitors, input devices (scanners and digital cameras), and output devices
(printers and plotters). It is the default color space used for HP products, Microsoft operating systems, the World Wide Web, and most office software. The sRGB standard represents the typical Windows monitor and is the convergence standard for high-definition television.
NOTE: Factors such as the type of monitor you use and the room lighting can affect the appearance of colors on your screen. For more information, see
.
64 Chapter 8 Color for Windows ENWW
The latest versions of Adobe PhotoShop ® , CorelDRAW ® , Microsoft Office, and many other programs use sRGB to communicate color. Because it is the default color space in Microsoft operating systems, sRGB has been adopted broadly. When programs and devices use sRGB to exchange color information, typical users experience greatly improved color matching.
The sRGB standard improves your ability to match colors between the product, the computer monitor, and other input devices automatically, and eliminates the need to become a color expert.
ENWW Advanced color use 65
66 Chapter 8 Color for Windows ENWW
9 Manage and maintain
●
●
●
●
●
●
●
●
ENWW 67
Information pages
Use the control panel to print information pages that give details about the product and its current settings.
1.
Press OK to open the menus.
2.
Press the Left arrow ( ) or Right arrow ( ) button to navigate to Reports, and then press OK .
3.
Press the Left arrow ( ) or Right arrow ( ) button to navigate through the reports, and then press
OK to print a report.
4.
Press X to exit the menus.
The following information pages are available:
● Demo page
● Menu structure
● Configuration page
● Supplies status page
● Network configuration page
● Usage report
● PCL font list
● PS font list
● PCL6 font list
● Color usage report
● Service report
● Diagnostics report
68 Chapter 9 Manage and maintain ENWW
HP ToolboxFX
Open HP ToolboxFX
Open HP ToolboxFX in one of these ways:
●
In the Windows system tray, double-click the HP ToolboxFX icon ( ).
● On the Windows Start menu, click Programs (or All Programs in Windows XP and Vista), click
HP, click HP Color LaserJet CP2020 Series, and then click HP ToolboxFX.
HP ToolboxFX contains the following folders:
●
●
●
Product information on page 71
●
●
●
ENWW HP ToolboxFX 69
Status
The Status folder contains links to the following main pages:
● Device status. This page indicates product conditions such as a jam or an empty tray. After you correct a problem, click Refresh status to update the product status.
● Supplies status. View details such as the approximate percent of toner remaining in the print cartridge and the number of pages that have been printed with the current print cartridge. This page also has links for ordering supplies and for finding recycling information.
● Device configuration. View a detailed description of the current product configuration, including the amount of memory installed and whether optional trays are installed.
● Network summary. View a detailed description of the current network configuration, including the
IP address and network status.
● Print info pages. Print the Configuration page and other information pages, such as the Supplies status page. See
Information pages on page 68 .
● Color usage job log. View color usage information for recently printed documents.
● Event log. View a history of product events. The most recent event is listed first.
Event log
The Event log is a table that contains codes corresponding to error messages that have appeared on the product control-panel display, a brief description of each error, and the number of pages that printed when each error occurred. For more information about error messages, see
Control-panel and statusalert messages on page 95 .
70 Chapter 9 Manage and maintain ENWW
Alerts
The Alerts folder contains links to the following main pages:
● Set up Status Alerts. Set up the product to send you pop-up alerts for certain events, such as low levels of cartridge life.
● Set up E-mail Alerts. Set up the product to send you e-mail alerts for certain events, such as low levels of cartridge life.
Set up Status Alerts
Use this to set up the product so that it sends alerts to your computer when jams, low levels of toner in
HP print cartridges, a non-HP print cartridge in use, empty input trays, and specific error messages occur.
Select to receive a pop-up, a system tray icon, a desktop alert, or any combination of these. The popup and desktop alerts only appear when the product is printing from the computer on which you set up the alerts. Desktop alerts are only visible momentarily, and disappear automatically.
Change the Cartridge low threshold setting, which sets the toner level that causes a low toner alert, on the System setup page.
NOTE: You must click Apply before your changes take effect.
Set up E-mail Alerts
Use this to configure up to two e-mail addresses to receive alerts when certain events occur. You can specify different events for each e-mail address. Use the information for the e-mail server that will send out the e-mail alert messages for the product.
NOTE: You can only configure e-mail alerts to be sent from a server that does not require user authentication. If your e-mail server requires you to log in with a username and password, you cannot enable e-mail alerts.
NOTE: You must click Apply before your changes take effect.
Product information
The Product information folder contains links to the following page:
● Demonstration Pages. Print pages that show the color print quality potential and overall print characteristics of the product.
Set password
Use HP ToolboxFX or the embedded Web server to set a system password.
1.
In the embedded Web server, click the Settings tab.
In HP ToolboxFX, click the Device Settings tab.
NOTE: If a password has already been set, you are prompted for it. Type the password, and then click Apply.
2.
Click Password.
ENWW HP ToolboxFX 71
3.
In the Password box, type the password that you want to set, and then in the Confirm
password box, type the same password again to confirm your choice.
4.
Click Apply to save the password.
Help
The Help folder contains links to the following main pages:
● Troubleshooting. View troubleshooting help topics, print troubleshooting pages, clean the product, and open Microsoft Office Basic Colors. For more information about Microsoft Office Basic
Colors, see Match colors on page 62 .
● Paper and Print Media. Print information about how to obtain optimal results from your product using various types of paper and print media.
● Color Printing Tools. Open Microsoft Office Basic Colors or the full palette of color with associated
● Animated Demonstrations. View animations that demonstrate how to perform common tasks on your device, such as how to get the best print quality, how to remove paper jams, and how to replace a print cartridge.
● User Guide. View information about the product usage, warranty, specifications, and support. The
User Guide is available in both HTML and PDF format.
72 Chapter 9 Manage and maintain ENWW
Device Settings
The Device Settings folder contains links to the following main pages:
● Device Information. View information such as the product description and a contact person.
● Paper Handling. Configure trays or change the product paper-handling settings, such as default paper size and default paper type.
● Printing. Change the default product print settings, such as number of copies and paper orientation.
● PCL5c. Change the PCL settings.
● PostScript. Change the PS settings.
● Print Quality. Change the print-quality settings.
● Print Density. Change the print-density settings, such as contrast, highlights, midtones, and shadows.
● Paper Types. Change the mode settings for each media type, such as letterhead, prepunched, or glossy paper.
● System Setup. Change the system settings, such as jam recovery and auto-continue. Change the
Cartridge low threshold setting, which sets the toner level that causes a low toner alert.
● Save/Restore Settings. Save the current settings for the product to a file on your computer. Use this file to load the same settings onto another product or to restore these settings to this product at a later time.
● Password. Set a password to protect the device settings. Once a password is set, users will be prompted to enter the password before being allowed to change device settings. This password is the same as the embedded Web server password.
Device Information
The Device Information page stores data about your product for future reference. The information that you type in the fields on this page appears on the Configuration page. You can type any character in each of these fields.
NOTE: You must click Apply before your changes take effect.
ENWW HP ToolboxFX 73
Paper Handling
Use these options to configure your default settings. These are the same options that are available on the control-panel menus on the control panel. For more information, see
.
The following options are available for handling print jobs when the product is out of media:
● Select Wait for paper to be loaded.
● Select Cancel from the Paper out action drop-down list to cancel the print job.
● Select Override from the Paper out time drop-down list to send the print job to another paper tray.
The Paper out time field specifies how long the product waits before acting on your selections. You can specify from 0 to 3600 seconds.
NOTE: You must click Apply before your changes take effect.
Printing
Use these options to configure the settings for all print functions. These are the same options that are available on the control panel. For more information, see
.
NOTE: You must click Apply before your changes take effect.
PCL5c
Use these options to configure the settings when you are using the PCL print personality.
NOTE: You must click Apply before your changes take effect.
PostScript
Use this option when you are using the PostScript print personality. When the Print PostScript error option is turned on, the PostScript error page automatically prints when PostScript errors occur.
NOTE: You must click Apply before your changes take effect.
74 Chapter 9 Manage and maintain ENWW
Print Quality
Use these options to improve the appearance of your print jobs. These are the same options that are available on the control panel menus. For more information, see
Control-panel menus on page 9 .
Color Calibration
● Power On Calibration. Specify whether the product should calibrate when you turn it on.
● Calibration Timing. Specify how frequently the product should calibrate.
● Calibrate Now. Set the product to calibrate immediately.
NOTE: You must click Apply before your changes take effect.
Print Density
Use these settings to make fine adjustments in the amount of each color of toner that is used for your printed documents.
● Contrasts. Contrast is the range of difference between light (highlight) and dark (shadow) colors.
To increase the overall range between light and dark colors, increase the Contrasts setting.
● Highlights. Highlights are colors that are nearly white. To darken highlight colors, increase the
Highlights setting. This adjustment does not affect midtone or shadow colors.
● Midtones. Midtones are colors that are halfway between white and solid density. To darken midtone colors, increase the Midtones setting. This adjustment does not affect highlight or shadow colors.
● Shadows. Shadows are colors that are nearly solid density. To darken shadow colors, increase the Shadows setting. This adjustment does not affect highlight or midtone colors.
Paper Types
Use these options to configure print modes that correspond to the various media types. To reset all modes to factory default settings, select Restore modes.
NOTE: You must click Apply before your changes take effect.
System Setup
Use these system settings to configure miscellaneous print settings. These settings are not available on the control panel.
NOTE: You must click Apply before your changes take effect.
Save/Restore Settings
Save the current settings for the product to a file on your computer. Use this file to load the same settings onto another product or to restore these settings to this product at a later time.
Password
Set a password to protect the device settings. After a password is set, users will be prompted to enter the password before they can access any of the HP ToolboxFX pages that read or write data from the device. This password is the same as the embedded Web server password.
ENWW HP ToolboxFX 75
Service
During the printing process, paper, toner, and dust particles can accumulate inside the product. Over time, this buildup can cause print-quality problems such as toner specks or smearing. HP ToolboxFX provides an easy method for cleaning the paper path.
Network Settings
The network administrator can use this tab to control the network-related settings for the product when it is connected to an IP-based network.
Shop for Supplies
This button, at the top of each page, links to a Web site where you can order replacement supplies. You must have Internet access to use this feature.
Other Links
This section contains links that connect you to the Internet. You must have Internet access in order to use any of these links. If you use a dial-up connection and did not connect when you first opened
HP ToolboxFX, you must connect before you can visit these Web sites. Connecting might require that you close HP ToolboxFX and reopen it.
● HP Instant Support. Connects to the HP Instant Support Web site.
● Support and Troubleshooting. Connects to the support site for the product where you can search for help with a specific problem.
● Product Registration. Connects to the HP product registration Web site.
76 Chapter 9 Manage and maintain ENWW
Embedded Web server
When the product is connected to the network, the embedded Web server is automatically available.
The embedded web server can be accessed through a standard web browser
NOTE: When the product is directly connected to a computer, use the HP ToolboxFX to view the product status.
Use the embedded Web server to view product and network status and to manage printing functions from your computer instead of from the product control panel.
● View product control status information.
● Set the type of paper loaded in each tray.
● Determine the remaining life of all supplies and order new ones.
● View and change tray configurations.
● View and change the product settings.
● View and change network configuration.
● View support content that is specific to the current state of the product.
● Restrict access to color-printing features.
To use the embedded Web server, you must have Microsoft Internet Explorer 6 or later, Netscape
Navigator 7 or later, Safari 1.2 or later, Konqueror 3.2 or later, Firefox 1.0 or later, Mozilla 1.6 or later, or Opera 7 or later. The embedded Web server works when the product is connected to an IP-based network. The embedded Web server does not support IPX-based or AppleTalk printer connections. You do not need Internet access to open and use the embedded Web server.
View the HP embedded Web server
1.
In a supported Web browser on your computer, type the IP address for the product in the address/
URL field. (To find the IP address, print a configuration page. See Information pages on page 68
.)
NOTE: After you open the URL, you can bookmark it so that you can return to it quickly in the future.
2.
The embedded Web server has three tabs that contain settings and information about the product: the Status tab, the Settings tab, and the Networking tab. Click the tab that you want to view.
See the following section for more information about each tab.
ENWW Embedded Web server 77
Embedded Web server sections
The table below describes the basic screens of the embedded Web server.
Tab or section Description
Status tab
Provides product, status, and configuration information.
● Device Status: Shows the product status and shows the life remaining of
HP supplies, with 0% indicating that a supply has reached the end of its estimated life.
● Supplies Status: Shows the approximate life remaining of HP supplies, with 0 percent indicating that a supply has reached the end of its estimated life. This page also provides supplies part numbers.
● Device Configuration: Shows the information found on the product Configuration page.
● Network Summary: Shows the information found on the product Network
Configuration page.
● Print Info Pages: Allows you to print the PCL, PCL6, PS Font Lists, and the supplies status page that the product generates.
● Color Usage Job Log: Shows user color print jobs on a job-by-job basis.
● Event Log: Shows a list of all product events and errors.
● Support button: Provides a link to the product support page. The Support button can be password-protected; see
● Shop for Supplies button: Provides a link to a page where you can order supplies for the product. The Shop for Supplies button can be password-protected; see
Settings tab
Provides the ability to configure the product from your computer.
● Device Information: Allows you to name the product and assign an asset number to it. Enter the name for the primary contact who will receive information about the product.
● Paper Handling: Allows you to change the paper-handling defaults for the product.
● Printing: Allows you to change the printing defaults for the product.
● PCL 5c: Allows you to change the PCL 5c defaults for the product.
● PostScript: Allows you to change the PostScript defaults for the product.
● Print Quality: Allows you to change the print quality defaults for the product, including calibration settings.
● Print Density: Allows you to change the contrasts, highlights, midtones, and shadows values for each supply.
● Paper Types: Allows you to configure print modes that correspond to the media types that the product accepts.
● System Setup: Allows you to change the system defaults for the product.
● Service: Allows you to start the cleaning procedure on the product.
● Support button: Provides a link to the product support page. The Support button can be password-protected.
● Shop for Supplies button: Provides a link to a page where you can order supplies for the product. The Shop for Supplies button can be password-protected.
78 Chapter 9 Manage and maintain ENWW
Tab or section
Networking tab
Provides the ability to change network settings from your computer.
Description
NOTE:
The Settings tab can be password-protected; see Set password on page 71 . If
this product is on a network, always consult with the printer administrator before changing settings on this tab.
Network administrators can use this tab to control network-related settings for the product when it is connected to an IP-based network.
NOTE: The Networking tab can be password-protected; see
.
ENWW Embedded Web server 79
Manage supplies
Supplies life
The print cartridge use HP ColorSphere toner. For information about the number of pages the cartridges can print, see www.hp.com/go/pageyield . Actual yield depends on specific use.
Print-cartridge storage
Do not remove the print cartridge from its package until you are ready to use it.
CAUTION: To prevent damage to the print cartridge, do not expose it to light for more than a few minutes.
HP policy on non-HP print cartridges
Hewlett-Packard Company cannot recommend the use of non-HP print cartridges, either new or remanufactured.
NOTE: Any damage caused by a non-HP print cartridge is not covered under the HP warranty and service agreements.
To install a new HP print cartridge, see
Replace print cartridges on page 82 . To recycle the used
cartridge, follow the instructions included with the new cartridge.
HP fraud hotline and Web site
Call the HP fraud hotline (1-877-219-3183, toll-free in North America) or go to www.hp.com/go/ anticounterfeit when you install an HP print cartridge and the control-panel message says the cartridge is non-HP. HP will help determine if the cartridge is genuine and take steps to resolve the problem.
Your print cartridge might not be a genuine HP print cartridge if you notice the following:
● You are experiencing a high number of problems with the print cartridge.
● The cartridge does not look like it usually does (for example, the orange pull tab is missing, or the packaging differs from HP packaging).
80 Chapter 9 Manage and maintain ENWW
Print when cartridge has reached estimated end of life
An Order Supplies message appears when a print cartridge is nearing the end of its life. A Replace
supplies message appears when the print cartridge has reached its estimated end of life. To ensure optimal print quality, HP recommends replacing a print cartridge when the Replace supplies message appears. Print-quality problems can occur when using a cartridge that has reached its estimated end of life, resulting in waste of print media and toner from other cartridges. Replacing a print cartridge when the Replace supplies message appears can prevent this waste.
The Auto continue feature in HP ToolboxFX allows the product to continue using a print cartridge that has reached the recommended replacement point.
WARNING!
Using the Auto continue feature can result in unsatisfactory print quality.
WARNING!
All print defects or supply failures incurred when an HP supply is used in cartridge-outoverride mode will not be considered to be defects in materials or workmanship in the supply under the
HP Print Cartridge Warranty Statement. For warranty information, see
Print cartridge limited warranty statement on page 129
.
You can enable or disable the Auto continue feature at any time, and you do not have to re-enable it when you install a new print cartridge. When the Auto continue feature is turned on, the product automatically continues printing when a print cartridge reaches the recommended replacement level. A
Replace Supplies Override In Use message appears while a print cartridge is being used in override mode. When you replace the print cartridge with a new supply, the product deactivates the override mode until another print cartridge reaches the recommended replacement level.
Enable or disable the Cartridge out override feature
1.
Open HP ToolboxFX.
2.
Click the Device Settings folder, and then click System Setup.
3.
Next to Auto continue select On to enable the feature. Select Off to disable it.
Enable or disable the Cartridge out override feature from the control panel
1.
On the control-panel menu, press OK .
2.
Use the Left arrow ( ) or the Right arrow ( ) button to select System setup, and then press
OK .
3.
Use the Left arrow ( ) or the Right arrow ( ) button to select Print quality, and then press OK .
4.
Use the Left arrow ( ) or the Right arrow ( ) button to select Replace supplies, and then press
OK .
5.
Select Override out to enable the feature. Select Stop at out to disable it.
ENWW Manage supplies 81
Replace print cartridges
1.
Open the front door.
2.
Pull out the print-cartridge drawer.
3.
Grasp the handle on the old print cartridge and then pull the cartridge straight up to remove it.
4.
Remove the new print cartridge from the packaging.
82 Chapter 9 Manage and maintain ENWW
5.
Remove the orange, plastic shield from the bottom of the new print cartridge.
CAUTION: Do not touch the imaging drum on the bottom of the print cartridge. Fingerprints on the imaging drum can cause print-quality problems.
6.
Insert the new print cartridge into the product.
ENWW Replace print cartridges 83
7.
Pull the tab on the left side of the print cartridge straight up to completely remove the sealing tape.
Discard the sealing tape.
8.
Close the print-cartridge drawer.
84 Chapter 9 Manage and maintain ENWW
9.
Close the front door.
10.
Place the old print cartridge in the box for the new print cartridge. Follow the recycling instructions that are included in the box.
ENWW Replace print cartridges 85
Memory and font DIMMs
Product memory
The product has one dual inline memory module (DIMM) slot. Use the DIMM slot to upgrade the product with the following items:
● More product memory (DIMMs are available in 64, 128, and 256 MB)
● Other DIMM-based printer languages and product options
● Support-language character sets (for example, Chinese characters or Cyrillic alphabet characters).
NOTE: To order DIMMs, see
Supplies and accessories on page 125 .
You might want to increase product memory if you often print complex graphics or HP postscript level 3 emulation documents, or if you use many downloaded fonts. Additional memory also enables multiple collated copies to print at the maximum speed.
Before ordering additional memory, see how much memory is currently installed by printing a
Configuration page. See
Information pages on page 68 .
CAUTION: Static electricity can damage electronic parts. When installing DIMMs, either wear an antistatic wrist strap, or frequently touch the surface of the DIMM antistatic package and then touch bare metal.
Install memory and font DIMMs
1.
Turn the product off, and then disconnect all power and interface cables.
2.
On the right side of the product, open the DIMM access door.
86 Chapter 9 Manage and maintain ENWW
ENWW
3.
Remove the DIMM access door.
4.
To replace a DIMM that is currently installed, spread the latches apart on each side of the DIMM slot, lift the DIMM up at an angle, and pull it out.
5.
Remove the new DIMM from the antistatic package, and then locate the alignment notch on the bottom edge of the DIMM.
Memory and font DIMMs 87
6.
Holding the DIMM by the edges, align the notch on the DIMM with the bar in the DIMM slot at an angle.
7.
Push down on the DIMM until both latches engage the DIMM. When the installation is correct, the metal contacts are not visible.
NOTE: If you have difficulty inserting the DIMM, make sure that the notch on the bottom of the
DIMM is aligned with the bar in the slot. If the DIMM still does not go in, make sure that you are using the correct DIMM type.
8.
Reinsert the DIMM access door.
88 Chapter 9 Manage and maintain ENWW
9.
Close the DIMM access door.
10.
Reconnect the power cable and USB or network cable, and then turn on the product.
11.
After installing a memory DIMM, see
ENWW Memory and font DIMMs 89
Enable memory
If you installed a memory DIMM, set the printer driver to recognize the newly added memory.
Enable memory for Windows
1.
On the Start menu, point to Settings, and click Printers or Printers and Faxes.
2.
Select this product and select Properties.
3.
On the Configure tab, click More.
4.
In the Total Memory field, type or select the total amount of memory that is now installed.
5.
Click OK.
Check DIMM installation
Turn the product on. Check that the product is in the Ready state after it has gone through the startup sequence. If an error message appears, do the following:
1.
Print a Configuration page. See
.
2.
Check the Installed Personalities and Options section on the Configuration page and compare it with the Configuration page that you printed before the DIMM installation.
3.
The DIMM might not be installed correctly. Repeat the installation procedure.
-or-
The DIMM may be defective. Try a new DIMM.
Clean the product
During the printing process, paper, toner, and dust particles can accumulate inside the product. Over time, this buildup can cause print-quality problems such as toner specks or smearing. This product has a cleaning mode that can correct and prevent these problems.
Clean the product using HP ToolboxFX
1.
Open HP ToolboxFX. See Open HP ToolboxFX on page 69 .
2.
Click the Device Settings folder, and then click the Service page.
3.
In the area for Cleaning Mode, click Start to begin the cleaning process.
The product processes a single page, and then returns to the Ready state when the cleaning process is complete.
Clean the product using the control panel
1.
Press OK to open the menus.
2.
Press the Left arrow ( ) or Right arrow ( ) button to highlight Service .
3.
Press OK . An asterisk (*) appears next to the active selection.
90 Chapter 9 Manage and maintain ENWW
4.
Press the Left arrow ( ) or Right arrow ( ) button to highlight Cleaning mode .
5.
Press OK .
Clean the product using the embedded Web server
1.
Open the embedded Web server.
2.
Click the Settings tab.
3.
Click the Service menu.
4.
Click Start.
Firmware updates
To upgrade the product firmware, download the firmware update file from www.hp.com/go/ ljcp2020series_software and save the file to your network or personal computer. Refer to the product install notes for instructions on how to install the firmware update file on the product.
ENWW Firmware updates 91
92 Chapter 9 Manage and maintain ENWW
10 Solve problems
●
Basic troubleshooting checklist
●
Control-panel and status-alert messages
●
●
●
●
●
ENWW 93
Basic troubleshooting checklist
If you are experiencing problems with the product, use the following checklist to identify the cause of the problem:
● Is the product connected to power?
● Is the product on?
● Is the product in the Ready state?
● Are all necessary cables connected?
● Are genuine HP supplies installed?
● Were recently replaced print cartridges installed correctly, and was the pull tab on the cartridge removed?
For additional information about installation and setup, see the getting started guide.
If you cannot find solutions to problems in this guide, go to www.hp.com/support/ljcp2020series .
Factors that affect product performance
Several factors affect the time it takes to print a job:
● Maximum product speed, measured in pages per minute (ppm)
● The use of special paper (such as transparencies, heavy paper, and custom-size paper)
● Product processing and download time
● The complexity and size of graphics
● The speed of the computer you are using
● The USB connection
94 Chapter 10 Solve problems ENWW
Control-panel and status-alert messages
The control-panel messages indicate the current product status or situations that might require action.
Status-alert messages appear on the computer screen (in addition to control-panel messages) when the product has certain problems. If a status-alert message is available, a appears in the Status
alert column in the following table.
Control-panel messages appear temporarily and might require that you acknowledge the message by pressing OK to resume printing or by pressing X to cancel the job. With certain messages, the job might not finish printing or the print quality might be affected. If the message is related to printing and the autocontinue feature is on, the product will attempt to resume printing after the message has appeared for
10 seconds without acknowledgement.
For some messages, restarting the product might fix the problem. If a critical error persists, the product might require service.
Control-panel message
10.00.XX Supply error
Status alert
10.10.XX Supply error
49 Error
Turn off then on
Description Recommended action
The supply memory for one of the print cartridges cannot be read or is missing.
Reinstall the print cartridge.
Turn the product off and then on.
● 10.0000 = black supply memory error
If the problem is not solved, replace the cartridge.
● 10.0001 = cyan supply memory error
● 10.0002 = magenta supply memory error
● 10.0003 = yellow supply memory error
● 10.1000 = black supply memory is missing
● 10.1001 = cyan supply memory is missing
● 10.1002 = magenta supply memory is missing
● 10.1003 = yellow supply memory is missing
Check the e-label. If it is broken or damaged, replace the cartridge.
Verify that the cartridge is installed in the correct location.
Remove and reinstall the cartridge and then power-cycle the product.
If the error is with a color cartridge, try swapping it with a different color cartridge in the tray. If the same message appears, then there is an engine problem. If a different 10.10.XX
message appears, replace the cartridge.
The product experienced an internal error.
Turn the product off, wait at least
30 seconds, and then turn the product on and wait for it to initialize.
If you are using a surge protector, remove it. Plug the product
ENWW Control-panel and status-alert messages 95
Control-panel message Status alert
50.X Fuser error
Turn off then on
51.XX Error
Turn off then on
54.XX Error
Turn off then on
55.X Error
Turn off then on
96 Chapter 10 Solve problems
Description Recommended action directly into the wall socket. Turn the product power on.
The product has experienced an error with the fuser.
If the message persists, contact
HP support.
Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize.
Turn off the product, wait at least
25 minutes, and then turn on the product.
If you are using a surge protector, remove it. Plug the product directly into the wall socket. Turn the product power on.
If the message persists, contact
HP support.
The product has experienced an internal hardware error.
Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize.
If you are using a surge protector, remove it. Plug the product directly into the wall socket. Turn the product on.
The product has experienced an error with one of the internal sensors.
If the message persists, contact
HP support.
1.
Open the door to the cartridge tray and slide out the cartridge tray.
● 54.15 = yellow
● 54.16 = magenta
● 54.17 = cyan
● 54.18 = black
2.
Inspect the white mechanism on the relevant cartridge. It is located on the right side of the cartridge.
3.
Push the mechanism in and out slowly. A black flag will raise up as you push it. It should move smoothly. If not, push repeatedly to try to free up any potential obstruction.
4.
Push in the cartridge tray and close the door.
If the message persists, contact
HP support.
The product has experienced an internal error.
Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize.
ENWW
Control-panel message Status alert
57.X Fan error
Turn off then on
59.X Error
Turn off then on
79 Error
Turn off then on
79 Service error
Turn off then on
ENWW
Description Recommended action
The product has experienced a problem with its internal fan.
An incompatible DIMM is installed.
If you are using a surge protector, remove it. Plug the product directly into the wall socket. Turn the product power on.
If the message persists, contact
HP support.
Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize.
The product has experienced a problem with one of the motors.
If you are using a surge protector, remove it. Plug the product directly into the wall socket. Turn the product power on.
If the message persists, contact
HP support.
Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize.
If you are using a surge protector, remove it. Plug the product directly into the wall socket. Turn the product power on.
If the message persists, contact
HP support.
The product has experienced an internal firmware error.
Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize.
If you are using a surge protector, remove it. Plug the product directly into the wall socket. Turn the product power on.
If the message persists, contact
HP support.
1.
Turn the product power off.
2.
Install a DIMM that the product supports. See
Service and support on page 127
for a list of supported DIMMs. See
for
DIMM installation instructions.
3.
Turn the product on.
If the message persists, contact
HP support.
Control-panel and status-alert messages 97
Control-panel message
<Color> in wrong position
Status alert
Device error
Press [OK]
Front Door open
Genuine HP supply installed
Incorrect supplies
Install <Color> cartridge
Invalid driver
Press [OK]
Jam in <location>
Jam in tray <X>
Clear jam and then Press [OK]
Load paper
Load tray # <TYPE> <SIZE>
Load tray 1 plain <SIZE>
Cleaning mode [OK] to start
Load tray 1 <TYPE> <SIZE>
Manual duplex
Load tray # Press [OK]
98 Chapter 10 Solve problems
Description Recommended action
A print cartridge is installed in the incorrect slot.
Be sure that each print cartridge is in the correct slot. From front to back, the print cartridges are installed in this order: black, cyan, magenta, yellow.
An internal error occurred.
Press OK to resume the job.
The product front door is open.
Close the door.
A genuine HP supply was installed. This message will appear briefly after the supply is installed and then be replaced by the message Ready.
No action necessary.
More than one print cartridge is installed in the incorrect slot.
Be sure that each print cartridge is in the correct slot. From front to back, the print cartridges are installed in this order: black, cyan, magenta, yellow.
The cartridge is either not installed or not correctly installed in the product.
Install the print cartridge. See
Replace print cartridges on page 82 .
You are using an incorrect printer driver.
Select the correct printer driver.
The product has detected a jam.
Clear the jam from the location indicated. The job should continue to print. If it does not, try reprinting the job.
If the message persists, contact
HP support.
The product has detected a jam.
Clear the jam from the location indicated, and then press OK .
All trays are empty.
If the message persists, contact
HP support.
Load print media.
A tray is configured for the media type and size that the print job is requesting, but that tray is empty.
Load the correct media into the tray, or press OK to use media in a different tray.
The product is ready to process the cleaning operation.
Load tray 1 with plain paper in the size indicated, and then press
OK .
No trays are configured for the media type and size that the print job is requesting.
Load the correct media into tray 1, or press OK to use media in a different tray.
The first side of a manual duplex job has printed, and the page needs to be loaded to process the second side.
Load the page in the indicated tray with the side to be printed face up, and the top of the page
ENWW
Control-panel message Status alert
Manual feed <TYPE> <SIZE>
Press [OK] for available media
Memory is low
Press [OK]
Try again later or turn off & on
Misprint
Press [OK]
Non HP supply installed
Order <color> cartridge
Order supplies
Print failure
Press [OK] If error repeats turn off then on
ENWW
Description Recommended action
The product is set for manual feed mode.
The product memory is almost full.
away from you and then press
OK .
Press OK to clear the message
or load the correct media into tray 1.
Press OK to finish the job, or press X to cancel the job.
Break the job into smaller jobs that contain fewer pages.
For information about increasing the product memory, see
Install memory and font DIMMs on page 86 .
Print media has been delayed as it moves through the product.
Press OK to clear the message.
A non-HP supply is installed.
The identified print cartridge is nearing the end of its useful life.
This message is temporary and will disappear after several seconds.
If you believe you purchased an
HP supply, go to www.hp.com/ go/anticounterfeit .
Service or repairs that are required as a result of using non-
HP supplies are not covered under HP warranty.
Order the identified print cartridge. Printing will continue until Replace <color> cartridge appears.
See Supplies and accessories on page 125
for more information.
More than one supply item is low. Check the supply-level gauges on the control panel, or print a
Supplies status page to determine which cartridges are low. See
Information pages on page 68 .
Order the identified print cartridges. Printing will continue until Replace <color> cartridge appears.
The product cannot process the page.
See Supplies and accessories on page 125
for more information.
Press OK to continue printing the job, but output might be affected.
Control-panel and status-alert messages 99
Control-panel message Status alert
Rear Door open
Remove shipping locks from
<color> cartridge
Remove shipping locks from all cartridges
Remove shipping material from rear door
Replace <color> cartridge
Replace supply
Override in use
Unexpected size in tray #
Load [size] Press [OK]
Used <color> Cartridge in use
Used supplies in use
Used supply installed
To accept Press [OK]
Description Recommended action
If the error persists, turn the power off and then on. Resend the print job.
Close the door.
The product rear door is open.
A print cartridge shipping lock is installed.
A print cartridge shipping lock is installed on one or more print cartridges.
Be sure that the print cartridge shipping lock has been removed.
Be sure that each print cartridge shipping lock has been removed.
The two shipping locks have not been removed from the rear roller.
The print cartridge has reached the end of life.
The Print quality menu item
Replace supplies is set to
Override out.
Open the rear door and remove the shipping locks.
Replace the cartridge. See
Replace print cartridges on page 82 .
You can continue printing until you notice a decrease in print quality.
See
System setup menu on page 11 .
The product has detected print media in the tray that does not match the configuration for the tray.
Load the correct media into the tray, or configure the tray for the size that you have loaded. See
Load paper and print media on page 50 .
No action necessary.
A used print cartridge was detected and accepted.
Used print cartridges are installed.
No action necessary.
A used print cartridge is installed. Press OK to continue.
100 Chapter 10 Solve problems ENWW
Clear jams
Common causes of jams
Cause Solution
The paper length and width guides are not adjusted correctly. Adjust the guides so they are against the paper stack.
The media does not meet specifications.
Use only media that meets HP specifications. See print media on page 43 .
You are using media that has already passed through a printer or copier.
Do not use media that has been previously printed on or copied.
An input tray is loaded incorrectly.
The media is skewed.
Remove any excess media from the input tray. Make sure that the stack is below the maximum stack height mark in the tray.
See Load paper and print media on page 50
.
The input-tray guides are not adjusted correctly. Adjust them so they hold the stack firmly in place without bending it.
The media is binding or sticking together.
Remove the media, flex it, rotate it 180 degrees, or flip it over.
Reload the media into the input tray.
The media is removed before it settles into the output bin.
NOTE: Do not fan paper. Fanning can create static electricity, which can cause paper to stick together.
Wait until the page completely settles in the output bin before removing it.
The media is in poor condition.
The internal rollers from the tray are not picking up the media. Remove the top sheet of media. If the media is heavier than
163 g/m 2 (43 lb), it might not be picked from the tray.
The media has rough or jagged edges.
The media is perforated or embossed.
Replace the media.
Replace the media.
Perforated or embossed media does not separate easily. Load sheets one at a time.
1
Paper was not stored correctly.
Replace the paper in the trays. Paper should be stored in the original packaging in a controlled environment.
If the product continues to jam, contact HP Customer Support or your authorized HP service provider.
ENWW Clear jams 101
Jam locations
Use this illustration to find the locations of jams.
1
2
3
4
5
6
Output bin
Tray 1
Tray 2
Optional tray 3
Fuser (behind the rear door)
Tray 2 jam-access area
Change Jam Recovery setting
When the Jam Recovery feature is turned on, the product reprints any pages that are damaged during a jam.
Use HP ToolboxFX to turn on the Jam Recovery feature.
1.
Open HP ToolboxFX.
2.
Click the Device Settings folder, and then click System Setup.
3.
Next to Jam Recovery, select On from the drop-down list.
Clear jams in tray 1
NOTE: If the sheet tears, make sure that all of the fragments are removed before you resume printing.
Pull the jammed sheet from tray 1.
102 Chapter 10 Solve problems ENWW
If paper has entered far enough into tray 1, remove tray 2, drop the tray 1 plate down, and then remove the paper from the opening.
Clear jams in tray 2
1.
Pull out tray 2 and place it on a flat surface.
2.
Lower the jam-access tray.
3.
Remove the jammed sheet by pulling it straight out.
ENWW Clear jams 103
4.
Replace tray 2.
5.
Press OK to continue printing.
Clear jams in tray 3
1.
Pull out tray 3 and place it on a flat surface.
2.
Remove the jammed sheet by pulling it straight out.
104 Chapter 10 Solve problems ENWW
3.
Replace tray 3.
4.
Press OK to continue printing.
Clear jams in fuser area
1.
Open the rear door.
2.
If necessary, push the guide (callout 1) and remove any visible paper (callout 2) from the bottom of the delivery area.
ENWW
NOTE: If the sheet tears, make sure that all fragments are removed before you resume printing.
Do not use sharp objects to remove fragments.
Clear jams 105
3.
Close the rear door.
106 Chapter 10 Solve problems ENWW
Clear jams in output bin
1.
Look for jammed paper in the output bin area.
2.
Remove any visible media.
NOTE: If the sheet tears, make sure that all fragments are removed before resuming printing.
3.
Open and then close the rear door to clear the message.
Clear jams in duplexer (duplexing models only)
1.
Open the rear door.
ENWW Clear jams 107
2.
If necessary, pull the guide (callout 1) and remove any visible paper (callout 2) from the bottom of the delivery area.
3.
If necessary, remove any visible paper from bottom side of the duplexing unit.
4.
If you can not see any jammed paper, lift the duplexing unit using the tab on the side of the duplexing unit.
5.
If you can see the trailing edge of the paper, remove the paper from the product.
108 Chapter 10 Solve problems ENWW
6.
If you can see the leading edge of the paper, remove it from the product.
7.
Close the rear door.
ENWW Clear jams 109
Solve image-quality problems
Occasionally, you might encounter problems with print quality. The information in the following sections helps you identify and resolve these issues.
Identify and correct print defects
Use the checklist and print-quality issues charts in this section to solve print-quality problems.
Print-quality checklist
General print-quality problems can be solved by using the following checklist:
1.
Make sure the shipping locks have been removed from the transfer roller inside the rear door.
2.
Make sure that the paper or print media that you are using meets specifications. Generally, smoother paper provides better results.
3.
If you are using a special print media such as labels, transparencies, glossy, or letterhead, ensure that you have printed by type.
4.
Print a Configuration page and Supplies status page. See Information pages on page 68 .
◦ Check the Supplies status page to see if any supplies are low or have reached their estimated end of life. No information is provided for non-HP print cartridges.
◦ If the pages do not print correctly, the problem is with the hardware. Contact HP Customer
Care. See
Service and support on page 127
or the flyer that came in the box.
5.
Print a Demo page from HP ToolboxFX. If the page prints, the problem is with the printer driver.
6.
Try printing from a different program. If the page prints correctly, the problem is with the program from which you were printing.
7.
Restart the computer and the product and try printing again. If the problem is not resolved, choose one of these options:
◦
If the problem is affecting all printed pages, see General print quality issues on page 111
.
◦ If the problem is affecting only pages printed in color, see
Solve issues with color documents on page 115 .
110 Chapter 10 Solve problems ENWW
General print quality issues
The following examples depict Letter-size paper that has passed through the product short-edge first.
These examples illustrate problems that would affect all of the pages that you print, whether you print in color or in black only. The topics that follow list the typical cause and solution for each of these examples.
Problem
Print is light or faded.
Toner specks appear.
Dropouts appear.
Cause Solution
The media might not meet
HP specifications.
One or more print cartridges might be defective.
Use media that meets HP specifications.
Print the Supplies status page to check the remaining life. See
Information pages on page 68 .
The product is set to override the
Replace <color> cartridge message and to continue printing.
Replace any low print cartridges. See
Replace print cartridges on page 82 .
Replace any low print cartridges. See
Replace print cartridges on page 82
The print density settings may have been changed.
Set the print density setting to 0.
The product may need to be calibrated.
Run a calibration. See
Calibrate the product on page 118 .
The media might not meet
HP specifications.
Use media that meets HP specifications.
The paper path might need cleaning.
One or more of the cartridges may be leaking.
The cartridge waste tank may be overfilled.
Clean the paper path. See Clean the product on page 90 .
Try to verify the color of the toner specks and check the cartridge for leaks.
A single sheet of print media might be defective.
Check for error code 10.98.XX in the event log. See
. The
XX portion of the code identifies the cartridge (00 is black, 01 is cyan, 02 is magenta, 03 is yellow). If the error was logged, replace the affected cartridge.
Try reprinting the job.
The moisture content of the paper is uneven or the paper has moist spots on its surface.
Try different paper, such as high-quality paper that is intended for color laser printers.
The paper lot is flawed. The manufacturing processes can cause some areas to reject toner.
Try different paper, such as high-quality paper that is intended for color laser printers.
ENWW Solve image-quality problems 111
Problem Cause Solution
Vertical streaks or bands appear on the page.
A
A
A
A a a a b b b b
B
B
B
B
B b c c c c c
C
C
C
C
C
The amount of background toner shading becomes unacceptable.
Toner smears appear on the media.
One or more print cartridges might be defective.
Print the Supplies status page to check
the remaining life. See Information pages on page 68 .
Use HP ToolboxFX to troubleshoot the problem.
Replace any low print cartridges. See
Replace print cartridges on page 82 .
Replace any low print cartridges. See
Replace print cartridges on page 82 .
The product is set to override the
Replace <color> cartridge message and to continue printing.
Very dry (low humidity) conditions can increase the amount of background shading.
One or more print cartridges might be defective.
The product is set to override the
Replace <color> cartridge message and to continue printing.
Check the device environment.
Replace any low print cartridges. See
Replace print cartridges on page 82 .
Replace any low print cartridges. See
Replace print cartridges on page 82 .
Smooth media shows more background than plain media
Consider using rougher media.
The media might not meet
HP specifications.
Use media that meets HP specifications.
If toner smears appear on the leading edge of the paper, the media guides are dirty, or debris has accumulated in the print path.
Clean the media guides.
Clean the paper path. See Clean the product on page 90 .
The toner smears easily when touched.
The device is not set to print on the type of media on which you want to print.
In the printer driver, select the Paper tab and set Type is to match the type of media on which you are printing. Print speed might be slower if you are using heavy paper.
The media might not meet
HP specifications.
Use media that meets HP specifications.
The paper path might need cleaning.
Clean the paper path. See Clean the product on page 90 .
112 Chapter 10 Solve problems ENWW
ENWW
Problem Cause Solution
Marks repeatedly appear at even intervals on the printed side of the page.
The device is not set to print on the type of media on which you want to print.
In the printer driver, select the Paper tab and set Type is to match the type of paper on which you are printing. Print speed might be slower if you are using heavy paper.
Internal parts might have toner on them. The problem typically corrects itself after a few more pages.
The paper path might need cleaning.
Clean the paper path. See product on page 90 .
The fuser might be damaged or dirty.
To determine if the fuser has a problem, open the HP ToolboxFX and print the
print-quality diagnostics page. See Open
.
Marks repeatedly appear at even intervals on the unprinted side of the page.
The printed page contains misformed characters.
A print cartridge may have a problem.
Internal parts might have toner on them. The problem typically corrects itself after a few more pages.
The paper path might need cleaning.
Clean the paper path. See product on page 90 .
The fuser might be damaged or dirty.
Contact HP Customer Care. See
Service and support on page 127 or the support
flyer that came in the box.
To determine which cartridge has a problem, open the HP ToolboxFX and print the print-quality diagnostics page.
See Open HP ToolboxFX on page 69
.
To determine if the fuser has a problem, open the HP ToolboxFX and print the
print-quality diagnostics page. See Open
.
Contact HP Customer Care. See
Service and support on page 127 or the support
flyer that came in the box.
The media might not meet
HP specifications.
Use a different paper, such as highquality paper that is intended for color laser printers.
If characters are incorrectly formed so that they produce a wavy effect, you may need to calibrate the product or the laser scanner might need service.
Verify that the problem also occurs on the Configuration page. If so, contact
HP Customer Care. See Service and support on page 127 or the support flyer
that came in the box.
Solve image-quality problems 113
Problem
The printed page is curled or wavy.
Text or graphics are skewed on the printed page.
Cause Solution
The device is not set to print on the type of media on which you want to print.
In the printer driver, select the Paper tab and set Type is to match the type of paper on which you are printing. Print speed might be slower if you are using heavy paper.
The Service menu item Less paper
curl is set to Off.
The media might not meet
HP specifications.
Use the control-panel menus to change the setting. See
.
Use a different paper, such as highquality paper that is intended for color laser printers.
Both high temperature and humidity can cause paper curl.
Check the device environment. Adjust curl modes from the control panel or
HP ToolboxFX.
The media might be loaded incorrectly.
Make sure that the paper or other print media is loaded correctly and that the media guides are not too tight or too
loose against the stack. See Load paper and print media on page 50
.
The media might not meet
HP specifications.
Use a different paper, such as highquality paper that is intended for color laser printers.
The printed page contains wrinkles or creases.
Toner appears around the printed characters.
The media might be loaded incorrectly.
Verify that the media is loaded correctly and that the media guides are not too tight or too loose against the stack. See
Load paper and print media on page 50 .
The media might not meet
HP specifications.
Turn over the stack of paper in the input tray, or try rotating the paper 180° in the input tray.
Use a different paper, such as highquality paper that is intended for color laser printers.
The media might be loaded incorrectly.
Turn over the stack of paper in the tray.
If large amounts of toner have scattered around the characters, the paper might have high resistivity.
Use a different paper, such as highquality paper that is intended for color laser printers.
114 Chapter 10 Solve problems ENWW
Problem
An image that appears at the top of the page (in solid black) repeats farther down the page (in a gray field).
Cause Solution
Software settings might affect image printing.
In your software program, change the tone (darkness) of the field in which the repeated image appears.
In your software program, rotate the whole page 180° to print the lighter image first.
The order of images printed might affect printing.
Change the order in which the images are printed. For example, have the lighter image at the top of the page, and the darker image farther down the page.
A power surge might have affected the device.
If the defect occurs later in a print job, turn the device off for 10 minutes, and then turn on the device to restart the print job.
Use non-glossy media to help reduce the severity of the defect
Solve issues with color documents
This section describes issues that can occur when you print in color.
Problem Cause
Only black is printing when the document should be printing in color.
Color mode is not selected in your program or printer driver or the restric color setting is on..
The correct printer driver might not be selected in the program.
The device might not be correctly configured.
The color supply is out and the Color
Supply Out menu setting is set to
Continue Black.
Solution
Select color mode instead of grayscale mode or turn off the restrict color setting.
Select the correct printer driver.
Print a Configuration page (see
). If no color appears on the Configuration page, contact HP Customer Care. See
Service and support on page 127 or the support
flyer that came in the box.
Replace the color supply.
ENWW Solve image-quality problems 115
Problem Cause Solution
One or more colors are not printing, or are inaccurate.
Sealing tape might be on the print cartridges.
The media might not meet
HP specifications.
The device might be operating in excessively humid conditions.
One or more print cartridges might be defective.
The product is set to override the
Replace <color> cartridge message and to continue printing.
Verify that the sealing tape has been completely removed from the print cartridges.
Use a different paper, such as highquality paper that is intended for color laser printers.
Verify that the device environment is within humidity specifications.
Replace any low print cartridges. See
Replace print cartridges on page 82 .
Replace any low print cartridges. See
Replace print cartridges on page 82 .
One or more of the cartridges may not have been engaged properly by the print engine.
Remove and reinstall the cartridges.
A color is printing inconsistently after you load a new print cartridge.
Another print cartridge might be defective.
Remove the print cartridge for the color that is printing inconsistently and reinstall it.
The product is set to override the
Replace <color> cartridge message and to continue printing.
Replace any low print cartridges. See
Replace print cartridges on page 82 .
The colors on the printed page do not match the colors as they appear on the screen.
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
The finish on the printed color page is inconsistent.
The colors on your computer monitor might differ from the device output.
See
If extremely light colors or extremely dark colors on screen are not printing, your software program might interpret extremely light colors as white or extremely dark colors as black.
If possible, avoid using extremely light or extremely dark colors.
The media might not meet
HP specifications.
Use a different paper, such as highquality paper that is intended for color laser printers.
The media might be too rough.
Use a smooth paper or print media, such as a high-quality paper that is made for color laser printers. Generally, smoother media produces better results.
116 Chapter 10 Solve problems ENWW
Use HP ToolboxFX to troubleshoot print-quality problems
NOTE: Before proceeding, print a Supplies status page to see the approximate number of pages remaining for each print cartridge. See
Information pages on page 68 .
From the HP ToolboxFX software you can print a page that helps identify whether a specific print cartridge is causing the problem, or if the problem is with the product itself. The print-quality troubleshooting page prints five bands of color, which are divided into four overlapping sections. By examining each section, you can isolate the problem to a particular cartridge.
Section
3
4
1
2
Print-cartridge
Yellow
Cyan
Black
Magenta
ENWW
This page helps identify four general issues:
● Streaks in only one color: This is most likely a cartridge issue. Remove the cartridge and look for debris on it. If no debris is found and the defect continues after the cartridge is reinstalled, replace the cartridge.
● Streaks in all colors (in same location): Clean the printer and call for service if the problem continues.
● Repeating defect in multiple colors:
Repeating dot in multiple colors: If the dot repeats at roughly 57 or 58 mm, run a cleaning page to clean fuser and run several white pages of paper to clean the roller. If defect does not repeat at 57 or 58 mm, replace the cartridge of the color of the dot.
Repeating band in multiple colors: Contact HP Support.
● Single dot or Single band in one color: Print three or four additional troubleshooting pages. If the band or dot is only in one color on most of the pages, replace the cartridge of that color. If the band or dot moves to a different color, contact HP Support.
For more troubleshooting information, try the following:
● See
Solve image-quality problems on page 110
in this guide.
● Go to www.hp.com/support/ljcp2020series .
● Contact HP Customer Care. See
Service and support on page 127 ..
Solve image-quality problems 117
Print the print-quality troubleshooting page
1.
Open HP ToolboxFX. See Open HP ToolboxFX on page 69 .
2.
Click the Help folder, and then click the Troubleshooting page.
3.
Click the Print button, and then follow the directions on the printed pages.
Optimize and improve print quality
Always make sure that the Type is setting in the printer driver matches the type of paper that you are using.
Use the print-quality settings in the printer driver to prevent print-quality problems.
Use the Device Settings area in HP ToolboxFX to adjust settings that affect print quality. See Open
Calibrate the product
If you experience any print-quality problems, calibrate the product.
Calibrate the product using HP ToolboxFX
1.
Open HP ToolboxFX. See Open HP ToolboxFX on page 69 .
2.
Click the Device Settings folder, and then click the Print Quality page.
3.
In the area for Color Calibration, select the Calibrate Now check box.
4.
Click Apply to calibrate the product immediately.
Calibrate the product from the control panel
1.
On the control-panel menu, press OK .
2.
Use the Left arrow ( ) or the Right arrow ( ) button to select System setup, and then press
OK .
3.
Use the Left arrow ( ) or the Right arrow ( ) button to select Print quality, and then press OK .
4.
Use the Left arrow ( ) or the Right arrow ( ) button to select Calibrate color, and then press
OK .
5.
Use the Left arrow ( ) or the Right arrow ( ) button to select Calibrate now, and then press
OK to calibrate the product.
118 Chapter 10 Solve problems ENWW
Performance problems
Problem
Pages print but are totally blank.
Pages print very slowly.
Pages did not print.
Cause Solution
The sealing tape might still be in the print cartridges.
Verify that the sealing tape has been completely removed from the print cartridges.
The document might contain blank pages.
Check the document that you are printing to see if content appears on all of the pages.
The product might be malfunctioning.
To check the product, print a
Configuration page.
Print on a different type of media.
Heavier media types can slow the print job.
Complex pages can print slowly.
Paper type not set correctly.
The product might not be pulling media correctly.
Proper fusing may require a slower print speed to ensure the best print quality.
Select the type to match the paper.
Make sure paper is loaded in the tray correctly.
The media is jamming in the device.
The USB cable might be defective or incorrectly connected.
Other devices are running on your computer.
If the problem persists, you might need to replace the pickup rollers and the separation pad. See
Service and support on page 127
.
Clear the jam. See Clear jams on page 101
.
● Disconnect the USB cable at both ends and reconnect it.
● Try printing a job that has printed in the past.
● Try using a different USB cable.
The product might not share a USB port.
If you have an external hard drive or network switchbox that is connected to the same port as the product, the other device might be interfering. To connect and use the product, you must disconnect the other device or you must use two USB ports on the computer.
ENWW Performance problems 119
Product software problems
Problem Solution
A printer driver for the product is not visible in the Printer folder ● Reinstall the product software.
NOTE: Close any applications that are running. To close an application that has an icon in the system tray, right-click the icon, and select Close or Disable.
An error message was displayed during the software installation
● Try plugging the USB cable into a different USB port on the computer.
● Reinstall the product software.
NOTE: Close any applications that are running. To close an application that has an icon in the task bar, rightclick the icon, and select Close or Disable.
● Check the amount of free space on the drive where you are installing the product software. If necessary, free up as much space as you can, and reinstall the product software.
The product is in Ready mode, but nothing prints
● If necessary, run the Disk Defragmenter, and reinstall the product software.
● Print a Configuration page, and verify the product functionality.
● Verify that all of the cables are correctly seated and within specifications. This includes the USB and power cables.
Try a new cable.
120 Chapter 10 Solve problems ENWW
Solve Macintosh problems
Solve problems with Mac OS X
NOTE: If you are installing the product using a USB connection, do not connect the USB cable to the device and the computer before you install the software. Connecting the USB cable will cause the Mac
OS X to automatically install the product, but the installation will be faulty. You must then uninstall the product, disconnect the USB cable, reinstall the software from the product CD-ROM, and reconnect the
USB cable when the software prompts you.
The printer driver is not listed in the Print Center or Printer Setup Utility.
Cause Solution
The product software might not have been installed or was installed incorrectly.
Make sure that the product PPD file is in the following hard-drive folder:
LIBRARY/PRINTERS/PPDS/CONTENTS/RESOURCES/
<LANG>.LPROJ
The PPD file is corrupt.
, where <lang> is the two-letter language code for the language that you are using. If necessary, reinstall the software. See the getting started guide for instructions.
Delete the PPD file from the following hard-drive folder:
LIBRARY/PRINTERS/PPDS/CONTENTS/RESOURCES/
<LANG>.LPROJ
, where <lang> is the two-letter language code for the language that you are using. Reinstall the software. See the getting started guide for instructions.
The product name, IP address, or Bonjour printer name does not appear in the printer list in the Print & Fax Center or Printer Setup
Utility.
Cause Solution
The product might not be ready.
The wrong connection type might be selected.
Make sure that the cables are connected correctly, the product is on, and the Ready light is on. If you are connecting through a USB or
Ethernet hub, try connecting directly to the computer or use a different port.
Make sure that USB, IP Printing, or Bonjour is selected, depending on the type of connection.
The wrong product name, IP address, or Bonjour host name is being used.
Print a Configuration page (see Information pages on page 68 ). Verify
that the product name, IP address, or Bonjour host name on the
Configuration page matches the product name, IP address, or
Bonjour host name in the Print Center or Printer Setup Utility.
The interface cable might be defective or of poor quality.
Replace the interface cable with a high-quality cable.
The printer driver does not automatically set up your selected product in the Print Center or Printer Setup Utility.
Cause Solution
The product might not be ready.
Make sure that the cables are connected correctly, the product is on, and the Ready light is on. If you are connecting through a USB or
ENWW Solve Macintosh problems 121
The printer driver does not automatically set up your selected product in the Print Center or Printer Setup Utility.
Cause Solution
Ethernet hub, try connecting directly to the computer or use a different port.
The product software might not have been installed or was installed incorrectly.
Make sure that the product PPD file is in the following hard-drive folder:
LIBRARY/PRINTERS/PPDS/CONTENTS/RESOURCES/
<LANG>.LPROJ
The PPD file is corrupt.
The interface cable might be defective or of poor quality.
, where <lang> is the two-letter language code for the language that you are using. If necessary, reinstall the software. See the getting started guide for instructions.
Delete the PPD file from the following hard-drive folder:
LIBRARY/PRINTERS/PPDS/CONTENTS/RESOURCES/
<LANG>.LPROJ
, where <lang> is the two-letter language code for the language that you are using. Reinstall the software. See the getting started guide for instructions.
Replace the interface cable with a high-quality cable.
A print job was not sent to the product that you wanted.
Cause
The print queue might be stopped.
The wrong product name, IP address, or Bonjour printer name is being used.
Solution
Restart the print queue. Open Print Monitor and select Start Jobs.
Print a Configuration page (see Information pages on page 68 ). Verify
that the product name, IP address, or Bonjour printer name on the
Configuration page matches the product name, IP address, or
Bonjour printer name in the Print Center or Printer Setup Utility.
An EPS file prints with incorrect fonts.
Cause
This problem occurs with some programs.
Solution
● Try downloading the fonts that are contained in the EPS file to the product before printing.
● Send the file in ASCII format instead of binary encoding.
You are unable to print from a third-party USB card.
Cause
This error occurs when the software for USB printers is not installed.
Solution
When adding a third-party USB card, you might need the Apple USB
Adapter Card Support software. The most current version of this software is available from the Apple Web site.
122 Chapter 10 Solve problems ENWW
When connected with a USB cable, the product does not appear in the Print Center or Printer Setup Utility after the driver is selected.
Cause Solution
This problem is caused by either a software or a hardware component.
Software troubleshooting
● Check that your Macintosh supports USB and has the appropriate USB software from Apple.
● Verify that your Macintosh operating system is Mac
OS X V10.28 or later.
Hardware troubleshooting
● Check that the product is turned on.
● Verify that the USB cable is connected correctly.
● Check that you are using the appropriate high-speed USB cable.
● Ensure that you do not have too many USB devices drawing power from the chain. Disconnect all of the devices from the chain, and connect the cable directly to the USB port on the host computer.
● Check to see if more than two nonpowered USB hubs are connected in a row on the chain. Disconnect all of the devices from the chain and connect the cable directly to the USB port on the host computer.
NOTE: The iMac keyboard is a nonpowered USB hub.
ENWW Solve Macintosh problems 123
124 Chapter 10 Solve problems ENWW
A Supplies and accessories
Order supplies and accessories
Table A-1 Supplies and accessories
Part Part number Type/size
Print cartridges
For information about the yield for the cartridges, see www.hp.com/go/ pageyield . Actual yield depends on specific use.
Cables
Memory
CC530A
CC531A
CC532A
CC533A
C6518A
CB421A
CB422A
Optional tray 3
CB423A
CB500A
Reference materials 5851-1468
Black print cartridge with HP ColorSphere toner
Cyan print cartridge with HP ColorSphere toner
Yellow print cartridge with HP ColorSphere toner
Magenta print cartridge with HP ColorSphere toner
USB 2.0 printer cable (2-meter [6.5-foot] standard)
64MB DDR2 144 pin SDRAM DIMM
128MB DDR2 144 pin SDRAM DIMM
256MB DDR2 144 pin SDRAM DIMM
250-sheet input tray for standard sizes.
HP LaserJet Printer Family Print Media Specification Guide (see www.hp.com/support/ljpaperguide )
ENWW Order supplies and accessories 125
126 Appendix A Supplies and accessories ENWW
B Service and support
●
Hewlett-Packard limited warranty statement
●
Print cartridge limited warranty statement
●
●
●
●
ENWW 127
Hewlett-Packard limited warranty statement
HP PRODUCT
HP Color LaserJet CP2020 Series printers
DURATION OF LIMITED WARRANTY
One-year limited warranty
HP warrants to you, the end-user customer, that HP hardware and accessories will be free from defects in materials and workmanship after the date of purchase, for the period specified above. If HP receives notice of such defects during the warranty period, HP will, at its option, either repair or replace products which prove to be defective. Replacement products may be either new or equivalent in performance to new.
HP warrants to you that HP software will not fail to execute its programming instructions after the date of purchase, for the period specified above, due to defects in material and workmanship when properly installed and used. If HP receives notice of such defects during the warranty period, HP will replace software which does not execute its programming instructions due to such defects.
HP does not warrant that the operation of HP products will be uninterrupted or error free. If HP is unable, within a reasonable time, to repair or replace any product to a condition as warranted, you will be entitled to a refund of the purchase price upon prompt return of the product.
HP products may contain remanufactured parts equivalent to new in performance or may have been subject to incidental use.
Warranty does not apply to defects resulting from (a) improper or inadequate maintenance or calibration,
(b) software, interfacing, parts or supplies not supplied by HP, (c) unauthorized modification or misuse,
(d) operation outside of the published environmental specifications for the product, or (e) improper site preparation or maintenance.
TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTIES ARE EXCLUSIVE AND
NO OTHER WARRANTY OR CONDITION, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR
IMPLIED AND HP SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY, SATISFACTORY QUALITY, AND FITNESS FOR A PARTICULAR PURPOSE.
Some countries/regions, states or provinces do not allow limitations on the duration of an implied warranty, so the above limitation or exclusion might not apply to you. This warranty gives you specific legal rights and you might also have other rights that vary from country/region to country/region, state to state, or province to province.
HP's limited warranty is valid in any country/region or locality where HP has a support presence for this product and where HP has marketed this product. The level of warranty service you receive may vary according to local standards. HP will not alter form, fit or function of the product to make it operate in a country/region for which it was never intended to function for legal or regulatory reasons.
TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY STATEMENT
ARE YOUR SOLE AND EXCLUSIVE REMEDIES. EXCEPT AS INDICATED ABOVE, IN NO EVENT
WILL HP OR ITS SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL,
INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OR OTHER DAMAGE,
WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. Some countries/regions, states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT
LAWFULLY PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION TO
THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU.
128 Appendix B Service and support ENWW
Print cartridge limited warranty statement
This HP product is warranted to be free from defects in materials and workmanship.
This warranty does not apply to products that (a) have been refilled, refurbished, remanufactured or tampered with in any way, (b) experience problems resulting from misuse, improper storage, or operation outside of the published environmental specifications for the printer product or (c) exhibit wear from ordinary use.
To obtain warranty service, please return the product to place of purchase (with a written description of the problem and print samples) or contact HP customer support. At HP's option, HP will either replace products that prove to be defective or refund your purchase price.
TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTY IS EXCLUSIVE AND NO
OTHER WARRANTY OR CONDITION, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR
IMPLIED AND HP SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY, SATISFACTORY QUALITY, AND FITNESS FOR A PARTICULAR PURPOSE.
TO THE EXTENT ALLOWED BY LOCAL LAW, IN NO EVENT WILL HP OR ITS SUPPLIERS BE
LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT OR
DATA), OR OTHER DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT
LAWFULLY PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION TO
THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU.
ENWW Print cartridge limited warranty statement 129
End User License Agreement
PLEASE READ CAREFULLY BEFORE USING THIS SOFTWARE PRODUCT: This End-User License
Agreement (“EULA”) is a contract between (a) you (either an individual or the entity you represent) and
(b) Hewlett-Packard Company (“HP”) that governs your use of the software product (“Software”). This
EULA does not apply if there is a separate license agreement between you and HP or its suppliers for the Software, including a license agreement in online documentation. The term “Software” may include
(i) associated media, (ii) a user guide and other printed materials, and (iii) “online” or electronic documentation (collectively “User Documentation”).
RIGHTS IN THE SOFTWARE ARE OFFERED ONLY ON THE CONDITION THAT YOU AGREE TO
ALL TERMS AND CONDITIONS OF THIS EULA. BY INSTALLING, COPYING, DOWNLOADING, OR
OTHERWISE USING THE SOFTWARE, YOU AGREE TO BE BOUND BY THIS EULA. IF YOU DO
NOT ACCEPT THIS EULA, DO NOT INSTALL, DOWNLOAD, OR OTHERWISE USE THE
SOFTWARE. IF YOU PURCHASED THE SOFTWARE BUT DO NOT AGREE TO THIS EULA, PLEASE
RETURN THE SOFTWARE TO YOUR PLACE OF PURCHASE WITHIN FOURTEEN DAYS FOR A
REFUND OF THE PURCHASE PRICE; IF THE SOFTWARE IS INSTALLED ON OR MADE
AVAILABLE WITH ANOTHER HP PRODUCT, YOU MAY RETURN THE ENTIRE UNUSED
PRODUCT.
1. THIRD PARTY SOFTWARE. The Software may include, in addition to HP proprietary software
(“HP Software”), software under licenses from third parties (“Third Party Software” and “Third Party
License”). Any Third Party Software is licensed to you subject to the terms and conditions of the corresponding Third Party License. Generally, the Third Party License is located in a file such as license.txt; you should contact HP support if you cannot find any Third Party License. If the Third Party
Licenses include licenses that provide for the availability of source code (such as the GNU General
Public License) and the corresponding source code is not included with the Software, then check the product support pages of HP’s website (hp.com) to learn how to obtain such source code.
2. LICENSE RIGHTS. You will have the following rights provided you comply with all terms and conditions of this EULA: a. Use. HP grants you a license to Use one copy of the HP Software. “Use” means installing, copying, storing, loading, executing, displaying, or otherwise using the HP Software. You may not modify the
HP Software or disable any licensing or control feature of the HP Software. If this Software is provided by HP for Use with an imaging or printing product (for example, if the Software is a printer driver, firmware, or add-on), the HP Software may only be used with such product (“HP Product”). Additional restrictions on Use may appear in the User Documentation. You may not separate component parts of the HP Software for Use. You do not have the right to distribute the HP Software.
b. Copying. Your right to copy means you may make archival or back-up copies of the HP Software, provided each copy contains all the original HP Software’s proprietary notices and is used only for backup purposes.
3. UPGRADES. To Use HP Software provided by HP as an upgrade, update, or supplement (collectively
“Upgrade”), you must first be licensed for the original HP Software identified by HP as eligible for the
Upgrade. To the extent the Upgrade supersedes the original HP Software, you may no longer use such
HP Software. This EULA applies to each Upgrade unless HP provides other terms with the Upgrade. In case of a conflict between this EULA and such other terms, the other terms will prevail.
4. TRANSFER.
a. Third Party Transfer. The initial end user of the HP Software may make a one-time transfer of the
HP Software to another end user. Any transfer will include all component parts, media, User
Documentation, this EULA, and if applicable, the Certificate of Authenticity. The transfer may not be an indirect transfer, such as a consignment. Prior to the transfer, the end user receiving the transferred
130 Appendix B Service and support ENWW
ENWW
Software will agree to this EULA. Upon transfer of the HP Software, your license is automatically terminated.
b. Restrictions. You may not rent, lease or lend the HP Software or Use the HP Software for commercial timesharing or bureau use. You may not sublicense, assign or otherwise transfer the HP Software except as expressly provided in this EULA.
5. PROPRIETARY RIGHTS. All intellectual property rights in the Software and User Documentation are owned by HP or its suppliers and are protected by law, including applicable copyright, trade secret, patent, and trademark laws. You will not remove any product identification, copyright notice, or proprietary restriction from the Software.
6. LIMITATION ON REVERSE ENGINEERING. You may not reverse engineer, decompile, or disassemble the HP Software, except and only to the extent that the right to do so is allowed under applicable law.
7. CONSENT TO USE OF DATA. HP and its affiliates may collect and use technical information you provide in relation to (i) your Use of the Software or the HP Product, or (ii) the provision of support services related to the Software or the HP Product. All such information will be subject to HP’s privacy policy. HP will not use such information in a form that personally identifies you except to the extent necessary to enhance your Use or provide support services.
8. LIMITATION OF LIABILITY. Notwithstanding any damages that you might incur, the entire liability of
HP and its suppliers under this EULA and your exclusive remedy under this EULA will be limited to the greater of the amount actually paid by you for the Product or U.S. $5.00. TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HP OR ITS SUPPLIERS BE LIABLE FOR
ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES (INCLUDING
DAMAGES FOR LOST PROFITS, LOST DATA, BUSINESS INTERRUPTION, PERSONAL INJURY,
OR LOSS OF PRIVACY) RELATED IN ANY WAY TO THE USE OF OR INABILITY TO USE THE
SOFTWARE, EVEN IF HP OR ANY SUPPLIER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES AND EVEN IF THE ABOVE REMEDY FAILS OF ITS ESSENTIAL PURPOSE. Some states or other jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
9. U.S. GOVERNMENT CUSTOMERS. If you are a U.S. Government entity, then consistent with FAR
12.211 and FAR 12.212, Commercial Computer Software, Computer Software Documentation, and
Technical Data for Commercial Items are licensed under the applicable HP commercial license agreement.
10. COMPLIANCE WITH EXPORT LAWS. You will comply with all laws, rules, and regulations (i) applicable to the export or import of the Software, or (ii) restricting the Use of the Software, including any restrictions on nuclear, chemical, or biological weapons proliferation.
11. RESERVATION OF RIGHTS. HP and its suppliers reserve all rights not expressly granted to you in this EULA.
(c) 2007 Hewlett-Packard Development Company, L.P.
Rev. 11/06
End User License Agreement 131
Customer support
Get telephone support, free during your warranty period, for your country/region
Have the product name, serial number, date of purchase, and problem description ready.
Get 24-hour Internet support
Country/region phone numbers are on the flyer that was in the box with your product or at www.hp.com/support/ .
www.hp.com/support/ljcp2020series
Get support for products used with a Macintosh computer www.hp.com/go/macosx
Download software utilities, drivers, and electronic information www.hp.com/go/ljcp2020series_software
Order supplies and paper
Order genuine HP parts or accessories
Order additional HP service or maintenance agreements www.hp.com/go/suresupply www.hp.com/buy/parts www.hp.com/go/carepack
132 Appendix B Service and support ENWW
Repack the product
If your product needs to be moved or shipped to another location, perform the following procedure to repack it.
CAUTION: Shipping damage as a result of inadequate packing is the customer's responsibility. The product must remain upright during shipment.
Repack the product
CAUTION: It is extremely important to remove the print cartridges before shipping the product. Print cartridges left in the product during shipping will leak and entirely cover the product with toner.
To prevent damage to the print cartridges, avoid touching the rollers, and store them in the original packing material or so that they are not exposed to light.
1.
Remove all four print cartridges and ship separately.
2.
Use the original shipping container and packing material, if possible. If you have already disposed of the packing material, contact a local mailing service for information about repacking the product.
HP recommends insuring the equipment for shipment.
ENWW Repack the product 133
Service information form
WHO IS RETURNING THE EQUIPMENT?
Person to contact:
Alternate contact:
Return shipping address: Special shipping instructions:
Date:
Phone:
Phone:
WHAT ARE YOU SENDING?
Model name: Model number: Serial number:
Please attach any relevant printouts. Do NOT ship accessories (manuals, cleaning supplies, and so on) that are not required to complete the repair.
HAVE YOU REMOVED THE PRINT CARTRIDGES?
You must remove them before shipping the printer, unless a mechanical problem prevents you from doing so.
[ ] Yes.
[ ] No, I cannot remove them.
WHAT NEEDS TO BE DONE? (Attach a separate sheet if necessary.)
1. Describe the conditions of the failure. (What was the failure? What were you doing when the failure occurred? What software were you running? Is the failure repeatable?)
2. If the failure is intermittent, how much time elapses between failures?
3. If the unit connected to any of the following, give the manufacturer and model number.
Personal computer:
4. Additional comments:
Modem: Network:
HOW WILL YOU PAY FOR THE REPAIR?
[ ] Under warranty Purchase/received date:
(Attach proof of purchase or receiving document with original received date.)
[ ] Maintenance contract number:
[ ] Purchase order number:
Except for contract and warranty service, a purchase order number and/or authorized signature must accompany any request for
service. If standard repair prices do not apply, a minimum purchase order is required. Standard repair prices can be obtained by contacting an HP-authorized repair center.
Authorized signature:
Billing address: Special billing instructions:
Phone:
134 Appendix B Service and support ENWW
C Specifications
●
●
●
●
ENWW 135
Physical specifications
Table C-1 Physical specifications
Product Height
Non-duplexing model
Duplexing model
Depth Width Weight
322 mm (12.7 inches) 454 mm (17.9 inches) 405 mm (15.9 inches) 19.90 kg (43.78 lb)
322 mm (12.7 inches) 484 mm (19.1 inches) 400 mm (15.7 inches) 21.10 kg (46.42 lb)
136 Appendix C Specifications ENWW
Electrical specifications
WARNING!
Power requirements are based on the country/region where the product is sold. Do not convert operating voltages. This may damage the product and void the product warranty.
Table C-2 Electrical specifications
Item 110-volt models 220-volt models
Power requirements 100 to 127 V (+/-10%)
50 to 60 Hz (+/-2 Hz)
Minimum recommended circuit capacity 6.0 A
220 to 240 V (+/-10%)
50 to 60 Hz (+/-2 Hz)
3.0 A
Table C-3 Power consumption (average, in watts)
Product Model
Ready
Sleep
1
2
3
4
HP Color LaserJet CP2020
Series Printer 260 13 3.8
0.0
Values are based on preliminary data, see www.hp.com/support/ljcp2020series for current information.
The power consumption reflects the highest values measured for color and monochrome printing when using all standard voltages.
HP Color LaserJet CP2020 Series print speed is 21 pages per minute (ppm) on letter-size media and 20 ppm on A4-size media in black-and-white or color.
Maximum heat dissipation for all models in Ready mode = 41 BTU/Hour.
ENWW Electrical specifications 137
Acoustic emissions
Table C-4 HP Color LaserJet CP2020 Series
,
Sound power level Declared per ISO 9296
Ready
L
WAd
= 6.4 Bels (A) [64dB (A)]
L
WAd
= Inaudible
Sound pressure level: bystander position
Declared per ISO 9296
L pAm
= 67 dB (A)
1
2
3
Ready L pAm
= Inaudible
Values are based on preliminary data, see www.hp.com/support/ljcp2020series for current information.
Configuration tested: HP Color LaserJet CP2020 Series monochrome simplex printing.
HP Color LaserJet CP2020 Series speed is 21/20 ppm for color printing and 21/20 ppm for monochrome printing (Letter/A4 size).
Environmental specifications
Table C-5 Operating-environment specifications
Environment Recommended
Temperature
Humidity
Altitude
15° to 27°C (59° to 80.6°F)
20% to 60% relative humidity (RH)
Not applicable
Allowed
10° to 30°C (50° to 86°F)
10% to 80% RH
0 to 3048 m (0 to 10,000 ft)
NOTE: These values are based on preliminary data. See www.hp.com/support/ljcp2020series for current information.
138 Appendix C Specifications ENWW
D Regulatory information
●
●
Environmental product stewardship program
●
●
Country/region specific statements
ENWW 139
FCC regulations
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If this equipment is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase separation between equipment and receiver.
● Connect equipment to an outlet on a circuit different from that to which the receiver is located.
● Consult your dealer or an experienced radio/TV technician.
NOTE: Any changes or modifications to the printer that are not expressly approved by HP could void the user’s authority to operate this equipment.
Use of a shielded interface cable is required to comply with the Class B limits of Part 15 of FCC rules.
140 Appendix D Regulatory information ENWW
Environmental product stewardship program
Protecting the environment
Hewlett-Packard Company is committed to providing quality products in an environmentally sound manner. This product has been designed with several attributes to minimize impacts on our environment.
Ozone production
This product generates no appreciable ozone gas (O
3
).
Power consumption
Power usage drops significantly while in Ready/Sleep mode, which saves natural resources and saves money without affecting the high performance of this product. To determine the ENERGY STAR® qualification status for this product see the Product Data Sheet or Specifications Sheet. Qualified products are also listed at: http://www.hp.com/hpinfo/globalcitizenship/environment/productdesign/ecolabels.html
Paper use
This product’s manual duplex feature (two-sided printing) and N-up printing (multiple pages printed on one page) capability can reduce paper usage and the resulting demands on natural resources.
Plastics
Plastic parts over 25 grams are marked according to international standards that enhance the ability to identify plastics for recycling purposes at the end of the product’s life.
HP LaserJet print supplies
It’s easy to return and recycle your HP LaserJet print cartridges that have reached estimated end of life
—free of charge—with HP Planet Partners. Multilingual program information and instructions are included in every new HP LaserJet print cartridge and supplies package. You help reduce the toll on the environment further when you return multiple cartridges together rather than separately.
HP is committed to providing inventive, high-quality products and services that are environmentally sound, from product design and manufacturing to distribution, customer use and recycling. When you participate in the HP Planet Partners program, we ensure your HP LaserJet print cartridges are recycled properly, processing them to recover plastics and metals for new products and diverting millions of tons of waste from landfills. Since this cartridge is being recycled and used in new materials, it will not be returned to you. Thank you for being environmentally responsible!
NOTE: Use the return label to return original HP LaserJet print cartridges only. Please do not use this label for HP inkjet cartridges, non-HP cartridges, refilled or remanufactured cartridges or warranty returns. For information about recycling your HP inkjet cartridges please go to http://www.hp.com/ recycle .
ENWW Environmental product stewardship program 141
Return and recycling instructions
United States and Puerto Rico
The enclosed label in the HP LaserJet toner cartridge box is for the return and recycling of one or more
HP LaserJet print cartridges after use. Please follow the applicable instructions below.
Multiple returns (two to eight cartridges)
1.
Package each HP LaserJet print cartridge in its original box and bag.
2.
Tape up to eight single boxes together using strapping or packaging tape (up to 70 lbs).
3.
Use a single pre-paid shipping label.
OR
1.
Use your own suitable box, or request a free bulk collection box from the http://www.hp.com/ recycle or 1-800-340-2445 (holds up to eight HP LaserJet print cartridges).
2.
Use a single pre-paid shipping label.
Single returns
1.
Package the HP LaserJet print cartridge in its original bag and box.
2.
Place the shipping label on the front of the box.
Shipping
For all HP LaserJet print cartridge recycling returns, give the package to UPS during your next delivery or pickup, or take it to an authorized UPS drop-off center. For the location of your local UPS drop-off center, call 1-800-PICKUPS or visit http://www.ups.com
. If you are returning via USPS label, give the package to a U.S. Postal Service carrier or drop off at a U.S.Postal Service Office. For more information, or to order additional labels or boxes for bulk returns, visit http://www.hp.com/recycle or call
1-800-340-2445. Requested UPS pickup will be charged normal pickup rates. Information subject to change without notice.
Non-US returns
To participate in HP Planet Partners return and recycling program, just follow the simple directions in the recycling guide (found inside the packaging of your new printer supply item) or visit http://www.hp.com/recycle . Select your country/region for information on how to return your HP LaserJet printing supplies.
Paper
This product is capable of using recycled papers when the paper meets the guidelines outlined in the
HP LaserJet Printer Family Print Media Guide. This product is suitable for the use of recycled paper according to EN12281:2002.
Material restrictions
This HP product does not contain added mercury.
This HP product does not contain a battery.
142 Appendix D Regulatory information ENWW
Disposal of waste equipment by users in private households in the
European Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Material Safety Data Sheet (MSDS)
Material Safety Data Sheets (MSDS) for supplies containing chemical substances (for example, toner) can be obtained by contacting the HP Web site at www.hp.com/go/msds or www.hp.com/hpinfo/ globalcitizenship/environment .
For more information
To obtain information about these environmental topics:
● Product environmental profile sheet for this and many related HP products
● HP’s commitment to the environment
● HP’s environmental management system
● HP’s end-of-life product return and recycling program
● Material Safety Data Sheets
Visit www.hp.com/go/environment or www.hp.com/hpinfo/globalcitizenship/environment .
ENWW Environmental product stewardship program 143
Declaration of conformity
according to ISO/IEC 17050-1 and EN 17050-1; DoC#: BOISB-0701–00–rel. 1.0
Manufacturer’s Name:
Manufacturer's Address:
Hewlett-Packard Company
11311 Chinden Boulevard,
Boise, Idaho 83714-1021, USA declares, that the product
Product Name:
Regulatory Model: 2)
HP Color LaserJet CP2020 Series
BOISB-0701-00
Product Options:
Toner Cartridges:
Including: CB500A— Optional 250-Sheet Input Tray
All
CC530A, CC531A, CC532A, CC533A conforms to the following Product Specifications:
SAFETY:
EMC:
IEC 60950-1:2001 / EN60950-1: 2001 +A11
IEC 60825-1:1993 +A1+A2 / EN 60825-1:1994 +A1 +A2 (Class 1 Laser/LED Product) GB4943-2001
CISPR22:2005 / EN55022:2006 - Class B 1)
EN 61000-3-2:2000 +A2
EN 61000-3-3:1995 +A1
EN 55024:1998 +A1 +A2
FCC Title 47 CFR, Part 15 Class B / ICES-003, Issue 4
GB9254-1998, GB17625.1-2003
Supplementary Information:
The product herewith complies with the requirements of the EMC Directive 2004/108/EEC and the Low Voltage Directive 2006/95/EC, and carries the CE-Marking accordingly.
This Device complies with Part 15 of the FCC Rules. Operation is subject to the following two Conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
1) The product was tested in a typical configuration with Hewlett-Packard Personal Computer Systems.
2) For regulatory purposes, these products are assigned a Regulatory model number. This number should not be confused with the product name or the product number(s).
Boise, Idaho 83713, USA
December, 2007
For Regulatory Topics Only:
European Contact Your Local Hewlett-Packard Sales and Service Office or Hewlett-Packard Gmbh, Department HQ-TRE / Standards
Europe, Herrenberger Strasse 140, D-71034 Böblingen, Germany, (FAX+49-7031-14-3143), http://www.hp.com/go/ certificates
USA Contact Product Regulations Manager, Hewlett-Packard Company, PO Box 15, Mail Stop 160, Boise, ID 83707-0015, USA,
(Phone: 208-396-6000)
144 Appendix D Regulatory information ENWW
Country/region specific statements
Laser safety
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration has implemented regulations for laser products manufactured since August 1, 1976. Compliance is mandatory for products marketed in the United States. The device is certified as a “Class 1” laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968. Since radiation emitted inside the device is completely confined within protective housings and external covers, the laser beam cannot escape during any phase of normal user operation.
WARNING!
Using controls, making adjustments, or performing procedures other than those specified in this user guide may result in exposure to hazardous radiation.
Canadian DOC regulations
Complies with Canadian EMC Class B requirements.
« Conforme à la classe B des normes canadiennes de compatibilité électromagnétiques. « CEM ». »
VCCI statement (Japan)
Power cord statement (Japan)
EMI statement (Korea)
ENWW Country/region specific statements 145
Laser statement for Finland
Luokan 1 laserlaite
Klass 1 Laser Apparat
HP Color LaserJet CP2020 Series, laserkirjoitin on käyttäjän kannalta turvallinen luokan 1 laserlaite.
Normaalissa käytössä kirjoittimen suojakotelointi estää lasersäteen pääsyn laitteen ulkopuolelle.
Laitteen turvallisuusluokka on määritetty standardin EN 60825-1 (1994) mukaisesti.
VAROITUS !
Laitteen käyttäminen muulla kuin käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING !
Om apparaten används på annat sätt än i bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.
HUOLTO
HP Color LaserJet CP2020 Series - kirjoittimen sisällä ei ole käyttäjän huollettavissa olevia kohteita.
Laitteen saa avata ja huoltaa ainoastaan sen huoltamiseen koulutettu henkilö. Tällaiseksi huoltotoimenpiteeksi ei katsota väriainekasetin vaihtamista, paperiradan puhdistusta tai muita käyttäjän käsikirjassa lueteltuja, käyttäjän tehtäväksi tarkoitettuja ylläpitotoimia, jotka voidaan suorittaa ilman erikoistyökaluja.
VARO !
Mikäli kirjoittimen suojakotelo avataan, olet alttiina näkymättömällelasersäteilylle laitteen ollessa toiminnassa. Älä katso säteeseen.
VARNING !
Om laserprinterns skyddshölje öppnas då apparaten är i funktion, utsättas användaren för osynlig laserstrålning. Betrakta ej strålen. Tiedot laitteessa käytettävän laserdiodin säteilyominaisuuksista:
Aallonpituus 775-795 nm Teho 5 m W Luokan 3B laser.
146 Appendix D Regulatory information ENWW
Substances Table (China)
根据中国 子信息 品 染控制管理 办 法的要求而出台
Table D-1 有毒有害物 质 表
部件名称
铅 (Pb) 汞 (Hg) 镉 (Cd)
打印引擎
控制面板
塑料外壳
格式化板 组 件
碳粉盒
O
X
X
O
X
O
O
O
O
O
O
O
X
O
O
六价 铬 (Cr(VI)) 多 溴 溴 苯 (PBB)
(PBDE)
醚
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O: 表示在此部件所用的所有同 材料中， 所含的此有毒或有害物 均低于 SJ/T11363-2006 的限制要
求。
X: 表示在此部件所用的所有同 材料中， 至少一
种
所含的此有毒或有害物 高于 SJ/T11363-2006 的限
制要求。
NOTE: 引用的“
环
保使用期限” 是根据在正常温度和湿度条件下操作使用 品而确定的。
ENWW Country/region specific statements 147
148 Appendix D Regulatory information ENWW
Index
Symbols/Numerics
<Color> in wrong position error
A
accessories
advanced printing options
alerts viewing with HP Toolbox
alternative letterhead mode 56
auto continue
Automatic crossover
automatic crossover, setting 15
B
background, gray 112 bands, troubleshooting 112
bin, output
black and white printing
blank pages, troubleshooting 119
C cables
connecting network 33 connecting USB 33
canceling a print job 54 cancelling a print job 54
capacity
cartridges
status, viewing with HP Toolbox
cartridges, print
characters, troubleshooting 113
color
Microsoft Office Basic Colors
colored text
configure the product,
connecting
contrast
control panel automatic crossover,
network services, setting, IPv4,
restore defaults, network
ENWW Index 149
copies, number of
creases, troubleshooting 114 crooked pages 114
curl, paper
custom-size paper settings
customer support
D
default settings, restoring 14
device discovery over
Device Settings tab,
device status
DIMMs
dots per inch (dpi)
dpi (dots per inch)
drivers
Macintosh,
duplex printing
E
E-mail alerts tab,
embedded Web server
environment specifications 138
environmental stewardship
EPS files, troubleshooting 122
error messages, control panel 95
errors
European Union, waste
F
factory defaults, restoring 14
Finnish laser safety
firmware
first page
fonts
EPS files, troubleshooting 122
fuser
G
gray background,
grayscale
H
HP Toolbox FX
HP ToolboxFX
Microsoft Office Basic Colors
Print Quality Troubleshooting
supported operating
I image quality
150 Index ENWW
information pages
configuration 38 network configuration 38
interface ports
invalid driver error message 98
IP address
Macintosh,
J
jams
common causes of 101 locations 101
jams <location>
jams tray #
K
L landscape orientation
laser safety statements 145, 146
light print, troubleshooting 111
lightness faded print,
lines, troubleshooting
loading
loading media
loose toner, troubleshooting 112
M
Macintosh configure the product
supported operating
USB card,
Macintosh driver settings
Material Safety Data Sheet
media
custom-size, Macintosh
media jams. See jams memory
menus, control panel
Microsoft Office Basic Colors
multiple pages per sheet
N n-up printing
network operating systems
product discovery 36 protocols supported 36
Network port
Network services
Network Settings tab,
Networking tab, embedded Web
networks
embedded Web server,
ENWW Index 151
O
operating environment
operating systems supported 2,
operating systems, networks 34
ordering supplies
orientation
output bin
output quality
P
page too complex error
pages
blank 119 not printing 119 printing slowly 119
pages per sheet
paper covers, using different
custom-size, Macintosh
first and last pages, using
paper jams. See jams paper path
PCL drivers
portrait orientation
ports troubleshooting
PostScript settings,
print cartridges
status, viewing with HP Toolbox
print media
print on both sides
print quality
printing
Product information tab,
Q quality
R
recycling
HP printing supplies returns and
remote firmware upgrades
repetitive defects,
replacement parts, and
reports, product
configuration page 38 network configuration page 38
resize documents
resolution
152 Index ENWW
Restore defaults
S
scale documents
service
Services tab
settings
Settings tab, embedded Web
shipping lock error
Show IP address
size specifications, product 136
sizes, media
smeared toner,
software
software license
supported operating
special media
special paper
specifications
speed
status
viewing with HP Toolbox
Status tab, embedded Web
storing
supplies
shipping lock error
status, viewing with HP Toolbox
wrong position error
supply-status, Services tab
support
System Setup tab,
T
TCP/IP
operating systems
technical support
temperature specifications 138
text, troubleshooting
toner
toner cartridges. See print cartridges
tray 1
ENWW Index 153
tray 2
tray 3
trays
troubleshooting
configuration page,
lines, printed pages 112 loose toner 112
network configuration page,
pages not printing 119 pages printing slowly 119
two-sided printing
types, media
U
upgrade firmware
USB port
troubleshooting
V vertical lines,
W warranty
watermarks
wavy paper, troubleshooting 114
Web sites
Macintosh customer
Material Safety Data Sheet
Windows
supported operating
154 Index ENWW
*CB493-90908*
*CB493-90908*
CB493-90908
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
Key features
Fast print speeds: Up to 20 pages per minute (ppm) in black and color.
High-quality prints: 600 x 600 dpi resolution produces sharp text and vibrant colors.
Versatile paper handling: Supports a variety of paper sizes and types, including envelopes, labels, and transparencies.
Easy-to-use control panel: Intuitive buttons and a large LCD display make it simple to operate.
Compact design: Fits easily on a desktop or in a small office space.
Energy-efficient: Meets ENERGY STAR® standards to save energy and reduce environmental impact.
Mobile printing: Supports wireless printing from smartphones and tablets.
Automatic duplex printing: Saves paper and time by printing on both sides of the page.
Built-in USB and Ethernet connectivity: Connects easily to computers and networks.
Frequently asked questions
600 x 600 dpi.
Yes, it supports wireless printing from smartphones and tablets.
One main paper tray with a capacity of 150 sheets.
Up to 30,000 pages per month.
Windows, macOS, and Linux.