HP LaserJet P2014 User Guide
Pubblicità
Pubblicità
HP LaserJet P2010 Series
User Guide
HP LaserJet P2010 Series
User Guide
Copyright information
© 2007 Copyright Hewlett-Packard
Development Company, L.P.
Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under the copyright laws.
The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Part number: CB450-90906
Edition 2, 03/2007
Trademark credits
Microsoft ® and Windows ® are
U.S. registered trademarks of Microsoft
Corporation.
PostScript ® is a registered trademark of
Adobe Systems Incorporated.
Table of contents
To install printer software for Windows NT 4.0, Server 2003 (64-bit), Windows
ENWW iii
iv ENWW
Appendix A Accessory/Consumable addendum
Appendix B Service and support
ENWW v
Appendix C Printer specifications
Appendix D Regulatory information
Multiple returns (two to eight cartridges) ........................................ 116
Single returns ................................................................................. 116
Disposal of waste equipment by users in private households in the European Union .... 117
vi ENWW
1 Product basics
This chapter provides information on the following topics:
●
●
ENWW 1
Product features
The following are the standard features for this product.
Standard features
● 24 ppm (Letter-size), 23 ppm (A4–size)
● First page out in as few as 8.5 seconds
● 600 dpi (provides 600 x 600 dpi output with Resolution Enhancement Technology (REt) for improved text)
● FastRes 1200 (provides 1200 dpi effective output quality)
● ProRes 1200 (provides fine line detail at 1200 x 1200 dpi)
● 50-sheet multipurpose tray (tray 1)
● EconoMode
● Print watermarks, booklets, multiple pages per sheet (N-up), and first page on different media than the rest of the document
● 32 MB RAM
● 3,000-page or 7,000-page print cartridge
● Host-based, PCL 5e
● Compatible with USB 2.0 specifications
● Supported by Windows® 98 SE (PCL 5e printer driver only), Millenium Edition (Me) (PCL 5e printer driver only), NT® 4.0 (PCL 5e printer driver only) (Parallel connection only), 2000, Server 2003
(printer drivers only), XP® 32-bit, XP 64-bit (PCL 5e printer driver only), and Vista 32-bit
● Supported by Macintosh OS X v10.2.8, v10.3, v10.4 and later
● On/off switch
● Embedded Web server (EWS) with internal pages
● 26 PCL 5e fonts
Network model features
Products with the network feature include all of the standard features, except that it has an HP internal
IPv6-compatible network port instead of a parallel port.
2 Chapter 1 Product basics ENWW
Identify product parts
The following figures identify the components of the product.
Figure 1-1 Network model, front view
3
4
5
1
2
6
7
8
Output bin
Print-cartridge door
Tray 1 (50–sheet multipurpose tray)
Model number
Tray 2 (250-sheet enclosed input tray)
On/off switch
Print-cartridge-door button
Control panel
ENWW
Figure 1-2 Network and base models, back view
1
2
3
Straight-through output door
Power receptacle
HP internal network port (network-ready models only)
Identify product parts 3
4
5
6
7
USB port
Jam-clearing levers
Serial number
Parallel port (base model only)
4 Chapter 1 Product basics ENWW
2 Control panel
The printer control panel is comprised of six lights and two buttons. The lights produce patterns that identify the printer status.
ENWW
1
2
3
4
5
6
7
Jam light : Indicates a jam in the printer
Toner light : When the print cartridge is low, the Toner light illuminates. When the print cartridge is out of the printer, the
Toner light blinks.
Paper out light : Indicates the printer is out of paper
Attention light : Indicates the print cartridge door is open or other errors exist
Ready light : Indicates the printer is ready to print
Go button and light
Cancel button : To cancel the print job currently printing, press the Cancel button.
NOTE: See
Status-light patterns on page 67
for a description of the light patterns.
5
6 Chapter 2 Control panel ENWW
3 Connectivity
ENWW 7
Printer connections
USB and parallel connections
1.
Insert the software installation CD into the computer CD-ROM drive.
2.
If the installation program does not start automatically, browse the CD contents and run the
SETUP.EXE file.
3.
Follow the on-screen instructions.
NOTE: During the installation, there is a prompt to plug in the parallel or USB cable. Refer to the figures below.
Figure 3-1 Parallel connection
Figure 3-2 USB connection
Network connections
The Network model can connect to a network through the HP internal networking port. External network print servers are available for the non-network product model. The following list identifies what is required to add networking to any non-network product model.
8 Chapter 3 Connectivity ENWW
10/100Base-TX Networking options
● HP Jetdirect en3700
● HP Jetdirect 175x
● HP Jetdirect ew2400
To order the print server, see
10/100 networking print servers on page 98
.
Connect the printer to the network
To connect a networking-equipped product, you need the following items:
● Functional wired network
● CAT-5 Ethernet cable
To connect the printer to your network, perform the following steps:
1.
Connect the CAT-5 Ethernet cable to an available port on the Ethernet hub or router.
2.
Connect the Ethernet cable to the Ethernet port on the back of the printer.
3.
Verify that one of the network lights (10 or 100) is illuminated on the network port located on the back of the printer.
4.
Confirm that the product has been assigned an IP address by printing a Configuration page: When the printer is in the Ready state, press and hold the Go button for 5 seconds.
NOTE: To resolve network connection problems, see
Network-setup problem-solving on page 94
.
Install the printer software for the network printer
To use the printer on the network, install the printer software on a computer that is connected to the network.
ENWW Printer connections 9
10 Chapter 3 Connectivity ENWW
4 Software for Windows
ENWW 11
Supported operating systems
The product comes with software for the following operating systems:
● Windows® 98 SE (PCL 5e printer driver only)
● Windows Me (PCL 5e printer driver only)
● Windows NT 4.0 (PCL 5e printer driver only)
● Windows 2000
● Windows Server 2003 (32-bit)
● Windows Server 2003 (64-bit) (PCL 5e printer driver only)
For more information about upgrading from Windows 2000 Server to Windows Server 2003, using
Windows Server 2003 Point and Print, or using Windows Server 2003 Terminal Services and
Printing, go to http://www.microsoft.com/ .
● Windows XP (32-bit)
● Windows XP (64-bit) (PCL 5e printer driver only)
● Windows Vista (32-bit)
12 Chapter 4 Software for Windows ENWW
Windows printer drivers
A printer driver is the software that provides access to printer features and provides the means for the computer to print to the printer.
Windows driver types
This product features a host-based driver and a PCL 5e printer driver.
Install Windows software
To install printer software for Windows NT 4.0, Server 2003 (64-bit), Windows 98SE, Me, and XP (64-bit)
See the operating system documentation for instructions on installing a printer driver.
To install printer software for Windows 2000, XP (32-bit), Server 2003 (32-bit), and Vista
(32-bit)
Insert the software CD that came with the printer into the computer CD-ROM drive. Follow the on-screen installation instructions.
NOTE: If the Welcome screen does not open, click Start on the Windows task bar and then click Run . Type Z:\setup (where Z is your CD drive letter), and click OK .
Configure the Windows printer driver
Use one of the following methods to open the Windows printer driver from your computer:
Operating system
Windows 98 SE, Me,
2000, XP (32–bit and
64–bit), and Server
2003
To change the settings for all print jobs until the software program is closed
1.
On the File menu in the software program, click
Print .
2.
Select the name of the printer, and then click
Properties or
Preferences .
The steps can vary; this procedure is most common.
To change the print job default settings (for example, turn on
Print on Both Sides by default)
To change the configuration settings (for example, add a tray or enable/disable Manual
Duplexing)
1.
Click Start , click Settings , and then click Printers or
Printers and Faxes .
2.
Right-click the printer icon, and then select Printing
Preferences .
1.
Click Start , click Settings and then click Printers or
Printers and Faxes .
3.
Click the Device Settings tab.
,
2.
Right-click the printer icon, and then select
Properties .
ENWW Windows printer drivers 13
Embedded Web server (network model only)
You can use the embedded Web server to configure the printer, view status information, and obtain problem-solving information.
14 Chapter 4 Software for Windows ENWW
5 Software for Macintosh
ENWW 15
Macintosh printer drivers
A printer driver is the software component that provides access to printer features and provides the means for the computer to communicate with the printer.
Install the Macintosh printer driver
This section explains how to install the printing system software for Macintosh OS X v10.2.8, v10.3, v10.4 and later.
NOTE: USB queues are created automatically when the printer is attached to the computer.
However, the queue will use a generic PPD if the installer has not been run before the USB cable is connected. To change the queue PPD, open the Print Center or Printer Setup Utility, select the correct printer queue, and then click Show Info to open the Printer Info dialog box. In the pop-up menu, select Printer Model , and then, in the pop-up menu in which Generic is selected, select the correct PPD for the printer.
Use the following procedure to install the Macintosh printer driver:
1.
Insert the printer CD into the CD-ROM drive and run the installer.
2.
Double-click the CD icon on the desktop
3.
Double-click the Installer icon.
4.
Follow the instructions on the computer screen.
5.
Print a test page or a page from any software program to make sure that the printer software is correctly installed.
If installation fails, reinstall the software. If this fails, see the Late-Breaking Information section of the
Install Notes. The Install Notes are located on the printer CD or at the support Web site. (See
HP Customer Care on page 105 for the Web address.)
Configure the Macintosh printer driver
Use one of the following methods to open the Macintosh printer driver from your computer:
Operating System To change the settings for all print jobs until the software program is closed
To change the print job default settings (for example, turn on
Print on Both Sides by default)
To change the configuration settings (for example, add a tray or enable/disable Manual
Duplexing)
Macintosh OS X v10.2.8, v10.3, v10.4
and later
1.
On the File menu, click
Print .
2.
Change the settings that you want on the various pop-up menus.
1.
2.
On the
Print .
File menu, click
Change the settings that you want on the various pop-up menus.
1.
Open Printer Setup Utility by selecting the hard drive, clicking Applications , clicking Utilities , then double-clicking Printer
Setup Utility .
3.
On the Presets pop-up menu, click Save as and type a name for the preset.
2.
Click the print queue.
3.
On the Printers menu, click Show Info .
These settings are saved in the
Presets menu. To use the new settings, you must select the
4.
Click the
Options
Installable
menu.
16 Chapter 5 Software for Macintosh ENWW
Operating System To change the settings for all print jobs until the software program is closed
To change the print job default settings (for example, turn on
Print on Both Sides by default)
To change the configuration settings (for example, add a tray or enable/disable Manual
Duplexing) saved preset option every time you open a program and print.
ENWW Macintosh printer drivers 17
PostScript Printer Description files (PPDs)
PPDs, in combination with the HP postscript level 3 emulation driver, provide access to the printer features and allow the computer to communicate with the printer. An installation program for the PPDs is provided on the printer CD.
18 Chapter 5 Software for Macintosh ENWW
6 Print Media
This product supports a variety of paper and other print media in accordance with the guidelines in this user guide. Media that does not meet these guidelines might cause the following problems:
● Poor print quality
● Increased jams
● Premature wear on the printer, requiring repair
For best results, use only HP brand paper and print media. Hewlett-Packard Company cannot recommend the use of other brands. Because they are not HP products, HP cannot influence or control their quality.
It is possible for media to meet all of the guidelines in this user guide and still not produce satisfactory results. This might be the result of improper handling, unacceptable temperature and humidity levels, or other variables over which Hewlett-Packard has no control.
Before you purchase a large quantity of media, test the media and make sure that it meets the requirements specified in this user guide and in HP LaserJet Printer Family Media Guide . The guidelines can be downloaded from http://www.hp.com/support/ljpaperguide/ , or see
Supplies and accessories table on page 97
for more information about ordering the guidelines.
CAUTION: Using media that does not meet Hewlett-Packard's specifications might cause problems for the printer, requiring repair. This repair is not covered by the Hewlett-Packard warranty or service agreements.
ENWW 19
Understand paper and print media use
This product supports a variety of paper and other print media in accordance with the guidelines in this user guide. Paper or print media that does not meet these guidelines might cause the following problems:
● Poor print quality
● Increased jams
● Premature wear on the product, requiring repair
For best results, use only HP-brand paper and print media designed for laserjets or multiuse. Do not use paper or print media made for inkjet printers. Hewlett-Packard Company cannot recommend the use of other brands of media because HP cannot control their quality.
It is possible for paper to meet all of the guidelines in this user guide and still not produce satisfactory results. This might be the result of improper handling, unacceptable temperature and/or humidity levels, or other variables over which Hewlett-Packard has no control.
CAUTION: Using paper or print media that does not meet Hewlett-Packard's specifications might cause problems for the product, requiring repair. This repair is not covered by the Hewlett-
Packard warranty or service agreements.
20 Chapter 6 Print Media ENWW
Supported paper and print media sizes
This product supports a number of paper sizes, and it adapts to various media.
NOTE: To obtain best print results, select the appropriate paper size and type in your print driver before printing.
Table 6-1 Supported paper and print media sizes
Size Dimensions
B5 (JIS)
B5 (ISO)
B6 (ISO)
16k
16k
16k
8.5 x 13
(custom)
Custom
Letter
Legal
A4
Executive
A3
A5
A6
216 x 279 mm (8.5 x 11 inches)
216 x 356 mm (8.5 x 14 inches)
210 x 297 mm (8.27 x 11.69 inches)
184 x 267 mm (7.24 x 10.51 inches)
297 x 420 mm (11.69 x 16.54 inches)
148 x 210 mm (5.83 x 8.27 inches)
105 x 148 mm (4.13 x 5.83 inches)
182 x 257 mm (7.17 x 10.12 inches)
176 x 250 mm (6.93 x 9.84 inches)
125 x 176 mm (4.92 x 6.93 inches)
197 x 273 mm (7.75 x 10.75 inches)
184 x 260 mm (7.24 x 10.23 inches)
195 x 270 mm (7.68 x 10.63 inches)
216 x 330 mm (8.5 x 13 inches)
(76 - 216) x (127 - 356) mm ((3 - 8.5) x (5 -
14) inches)
Tray 1 Tray 2 Optional tray 3
Table 6-2 Supported envelopes and postcards
Size Dimensions
Envelope #10 105 x 241 mm (4.13 x 9.49 inches)
Envelope DL 110 x 220 mm (4.33 x 8.66 inches)
Envelope C5 162 x 229 mm (6.93 x 9.84 inches)
Envelope B5 176 x 250 mm (6.7 x 9.8 inches)
Envelope
Monarch
98 x 191 mm (3.9 x 7.5 inches)
Postcard
Double postcard
100 x 148 mm (3.94 x 5.83 inches)
148 x 200 mm (5.83 x 7.87 inches)
Tray 1 Tray 2 Optional tray 3
ENWW Supported paper and print media sizes 21
Custom paper sizes
This product supports a variety of custom paper sizes. Supported custom sizes are sizes that are within the minimum- and maximum-size guidelines for the product but are not listed in the supported paper sizes table. When using a supported custom size, specify the custom size in the print driver, and load the paper in a tray that supports custom sizes.
22 Chapter 6 Print Media ENWW
Special paper or print media guidelines
This product supports printing on special media. Use the following guidelines to obtain satisfactory results. When using special paper or print media, be sure to set the type and size in your print driver to obtain the best print results.
CAUTION: HP LaserJet printers use fusers to bond dry toner particles to the paper in very precise dots. HP laser paper is designed to withstand this extreme heat. Using inkjet paper not designed for this technology could damage your printer.
Media type
Envelopes
Labels
Transparencies
Letterhead or preprinted forms
Heavy paper
Glossy or coated paper
Do Do not
● Store envelopes flat.
● Use envelopes where the seam extends all the way to the corner of the envelope.
● Use peel-off adhesive strips that are approved for use in laser printers.
● Do not use envelopes that are wrinkled, nicked, stuck together, or otherwise damaged.
●
●
Do not use envelopes that have clasps, snaps, windows, or coated linings.
Do not use self-stick adhesives or other synthetic materials.
● Use only labels that have no exposed backing between them.
● Use Labels that lie flat.
●
●
Do not use labels that have wrinkles or bubbles, or are damaged.
Do not print partial sheets of labels.
● Use only full sheets of labels.
● Use only transparencies that are approved for use in laser printers.
● Place transparencies on a flat surface after removing them from the product.
● Do not use transparent print media not approved for laser printers.
● Use only letterhead or forms approved for use in laser printers.
● Use only glossy or coated paper that is approved for use in laser printers.
● Do not use raised or metallic letterhead.
● Use only heavy paper that is approved for use in laser printers and meets the weight specifications for this product.
● Do not use paper that is heavier than the recommended media specification for this product unless it is HP paper that has been approved for use in this product.
● Do not use glossy or coated paper designed for use in inkjet products.
ENWW Special paper or print media guidelines 23
Load media
The following sections describe how to load media into the different input trays.
CAUTION: If you try to print on media that is wrinkled, folded, or damaged in any way, a jam might occur. See
for more information.
Tray 1
Tray 1 is accessed from the front of the printer. The printer prints from tray 1 before attempting to print from other trays.
Media guides ensure that the media is correctly fed into the printer and that the print is not skewed
(crooked on the media). When loading media, adjust the media guides to match the width of the media that you are using.
Tray 2 and optional tray 3
Media guides ensure that the media feeds correctly into the printer and that the print is not skewed. Tray
2 has side and rear media guides. When loading media, adjust the media guides to match the length and width of the media that you are using.
24 Chapter 6 Print Media ENWW
NOTE: When you add new media, make sure that you remove all of the media from the input tray and straighten the stack of new media. This reduces jams by preventing multiple sheets of media from feeding through the printer at one time.
Straight-through output path
Use the straight-through output path when printing envelopes, transparencies, heavy media, or any media that tends to curl when printed. If you open the straight-through output door before printing media from tray 1, tray 2, or optional tray 3, the media exits the printer through the straight-through output path.
NOTE: Printed media does not stack when you use the straight-through output path. The media drops to the surface below unless you remove each sheet as it exits the printer.
Manual feed
You can use manual feed when printing mixed media. For example, you can use manual feed to print an envelope, then a letter, then an envelope, and so on. Load envelopes in tray 1 and load letterhead into tray 2.
To print using manual feed, open the printer Properties or Printer Setup, and then select Manual Feed
(tray 1) from the Source Tray drop-down list. See
Configure the Windows printer driver on page 13
or
Configure the Macintosh printer driver on page 16 for instructions. After you have enabled manual
feed, press the Go button to print.
ENWW Load media 25
26 Chapter 6 Print Media ENWW
7 Print tasks
This chapter provides information on the following topics:
●
●
●
●
Print multiple pages on a single sheet of paper (N-up printing)
●
●
●
ENWW 27
Media type and tray loading
This product has the following tray priority for feeding print media:
1.
Tray 1 (if open)
2.
Tray 2
3.
Optional Tray 3 (if attached)
Minimum media dimensions are 76 x 127 mm (3 x 5 inches).
Maximum media dimensions are 216 x 356 mm (8.5 x 14 inches).
To obtain the best print results, change the paper size and paper type settings in the printer driver before printing.
Table 7-1 Tray 1 media information
Type is Media specifications
Media quantity Driver settings Paper orientation Output
75 g/m 2 (20 lb) to
104 g/m 2 (27 lb)
Up to 50 sheets Plain or unspecified
N/A Straight-through output door
Plain
Color
Preprinted
Prepunched
Recycled
Light
Envelopes
Labels
Bond
Rough
Transparencies
Heavy
Letterhead
Cardstock
Shipping labels
60 g/m 2 (16 lb) to
75 g/m 2 (20 lb)
Less than 90 g/m 2
(24 lb)
Up to 50 sheets Light
Up to 10 envelopes Envelope
Standard Up to 10 sheets
75 g/m 2 (20 lb) to
104 g/m 2 (27 lb)
75 g/m 2 (20 lb) to
104 g/m 2 (27 lb)
4 mm (0.1 inches)
Monochrome
Overhead
90 g/m 2 (24 lb) to
105 g/m 2 (28 lb)
75 g/m 2 (20 lb) to
104 g/m 2 (27 lb)
Up to 10 sheets
Up to 10 sheets
Up to 10 sheets
Up to 10 sheets
Up to 10 sheets
Up to 10
Up to 10
Up to 10
Up to 10
Labels
Bond
Rough
Transparency
Heavy
Letterhead
Cardstock
Cardstock
N/A Straight-through output door
Short edge leading, flap on right side facing up
Straight-through output door
Side to be printed on facing up
Side to be printed on facing up
Side to be printed on facing up
Straight-through output door
Straight-through output door
Straight-through output door
Side to be printed on facing up
Straight-through output door
Side to be printed on facing up
Straight-through output door
Side to be printed on facing up, top of page in first
Output bin
Side to be printed on facing up
Side to be printed on facing up
Straight-through output door
Straight-through output door
28 Chapter 7 Print tasks ENWW
ENWW
Table 7-2 Tray 2 media information
Type is Media specifications
Media quantity
75 g/m 2 (20 lb) to
104 g/m 2 (27 lb)
Up to 250 sheets Plain
Color
Preprinted
Prepunched
Recycled
Light Up to 250 sheets
Labels
60 g/m 2 (16 lb) to
75 g/m 2 (20 lb)
Standard
Bond
Less than 250 sheets
Up to 250 sheets
Rough
Heavy
Transparencies
Letterhead
75 g/m 2 (20 lb) to
104 g/m 2 (27 lb)
75 g/m 2 (20 lb) to
104 g/m 2 (27 lb)
90 g/m 2 (24 lb) to
105 g/m 2 (28 lb)
4 mm (0.1 inch)
Monochrome
Overhead
75 g/m 2 (20 lb) to
104 g/m 2 (27 lb)
Up to 250 sheets
Less than 250 sheets
Less than 250 sheets
Less than 250 sheets
Driver settings
Plain or unspecified
Light
Labels
Bond
Rough
Heavy
Transparency
Letterhead
Paper orientation Output
N/A
N/A
Output bin
Output bin
Side to be printed on facing up
Side to be printed on facing up
Side to be printed on facing up
N/A
Straight-through output door
Output bin
Output bin
Output bin
Side to be printed on facing down
Straight-through output door
Side to be printed on facing down
Normal: output bin
Heavy: straight through output door
Table 7-3 Optional Tray 3 media information
Media type Media specifications
Media quantity
75 g/m 2 (20 lb) to
104 g/m 2 (27 lb)
Up to 250 sheets Plain
Color
Preprinted
Prepunched
Recycled
Light Up to 250 sheets
Bond
Rough
60 g/m 2 (16 lb) to
75 g/m 2 (20 lb)
75 g/m 2 (20 lb) to
104 g/m 2 (27 lb)
75 g/m 2 (20 lb) to
104 g/m 2 (27 lb)
Up to 250 sheets
Up to 250 sheets
Driver settings
Plain or unspecified
Light
Bond
Rough
Paper orientation Output
N/A
N/A
Output bin
Output bin
Side to be printed on facing up
Side to be printed on facing up
Output bin
Output bin
Media type and tray loading 29
Table 7-3 Optional Tray 3 media information (continued)
Media type Media specifications
Media quantity Driver settings
Heavy Heavy
Letterhead
90 g/m 2 (24 lb) to
105 g/m 2 (28 lb)
75 g/m 2 (20 lb) to
104 g/m 2 (27 lb)
Less than 250 sheets
Less than 250 sheets
Letterhead
Paper orientation Output
N/A
Side to be printed on facing down
Straight-through output door
Normal: output bin
Heavy: straight through output door
30 Chapter 7 Print tasks ENWW
Print-quality settings
Print-quality settings affect print resolution and toner usage.
Use the following procedure to change print-quality settings:
1.
Open the printer Properties (or Printing Preferences in Windows 2000 and XP). See Configure the
Windows printer driver on page 13
or
Configure the Macintosh printer driver on page 16 for
instructions.
2.
On the Paper/Quality tab or the Finishing tab (the Paper Type/Quality tab for some Mac drivers), select the print quality setting you want to use. The following options are available:
● ProRes 1200 : This setting provides fine-line detail at 1200 x 1200 dpi.
● FastRes 1200 : This setting provides 1200 dpi effective output quality.
● 600 dpi : This setting provides 600 x 600 dpi output with Resolution Enhancement technology
(REt) for improved text.
● EconoMode : Text is printed with less toner. This setting is useful when you are printing drafts.
You can turn on this option independently of other print-quality settings. See
for more information.
NOTE: Not all printer features are available in all drivers or operating systems. See the printer
Properties (driver) online Help for information about availability of features for that driver.
ENWW Print-quality settings 31
Manual two-sided printing
To manually print on both sides of the paper, you must run the paper through the printer twice. You can print using either of these options:
● Top output bin
● Straight-through output door (for heavy media or media that curls)
NOTE: Manual two-sided printing can cause the printer to become dirty, reducing print quality.
See
for instructions if the printer becomes dirty.
Manual two-sided printing using the top output bin
The following sections provide instructions for the different operating systems.
Microsoft Windows
1.
Close the straight-through output door.
2.
Print side one of the document using tray 1.
3.
After side one has printed, remove the remaining paper from tray 1 and set it aside until after you finish the manual two-sided print job.
32 Chapter 7 Print tasks ENWW
4.
Gather the printed pages, and straighten the stack.
i n v e n t
5.
Return the stack to tray 1 with the printed side down and the top edge toward the printer.
6.
Press the Go button to print side two.
Mac OS X
1.
Close the straight-through output door.
2.
If Manual Duplex does not appear as a printer option, perform the following steps: a.
Verify that HP Manual Duplex & Booklet (Classic) was selected when the software driver was installed with the Custom Install option.
b.
Do a File-Print , select Plug-In Preferences , and click the right-facing arrow. The right-facing arrow changes to a down-facing arrow, and the HP Manual Duplex & Booklet feature displays.
c.
Select Print Time Filters , select HP Manual Duplex & Booklet , and click Save Settings .
d.
Select Manual Duplex , and select Print on Both Sides .
3.
Print the document.
4.
After side one has printed, remove the remaining paper from tray 1 and set it aside until after you finish the manual two-sided print job.
5.
Gather the printed pages, and straighten the stack.
6.
Return the stack to tray 1 with the printed side down and the top edge toward the printer.
7.
Press the Go button on the control panel to print side two.
ENWW Manual two-sided printing 33
Manual two-sided printing using the straight-through output door
The following provides instructions for the different operating systems.
Microsoft Windows
1.
Open the straight-through output door.
2.
Open the printer Properties (or Printing Preferences in Windows 2000 and XP). See
Windows printer driver on page 13 for instructions.
3.
On the Finishing tab, select the Correct Order for Straight Paper Path check box.
NOTE: Not all printer features are available in all drivers or operating systems. See the printer Properties (driver) online Help for information about availability of features for that driver.
4.
On the Finishing tab, select the Print On Both Sides (Manually) check box.
NOTE: If the Print On Both Sides (Manually) option does not appear, the option may be disabled. Go to the printer Properties, select the Device Settings tab, and select Enable from the Allow Manual Duplex drop-down list to enable the option.
5.
Click OK .
6.
Print side one of the document from tray 1.
34 Chapter 7 Print tasks ENWW
7.
Gather the printed pages, and straighten the stack.
8.
Return the stack to tray 1 with the printed side facing down and the top edge toward the printer.
9.
Press the Go button to print side two.
Mac OS X
1.
Open the straight-through output door.
2.
If Manual Duplex does not appear as a printer option, perform the following steps: a.
Verify that HP Manual Duplex & Booklet (Classic) was selected when the software driver was installed with the Custom Install option.
b.
Do a File-Print , select Plug-In Preferences , and click the right-facing arrow. The right-facing arrow changes to a down-facing arrow, and the HP Manual Duplex & Booklet feature displays.
c.
Select Print Time Filters , select HP Manual Duplex & Booklet , and click Save Settings .
d.
Select Manual Duplex , and select Print on Both Sides .
e.
Select Alternate output bin is open (straight through paper path) .
ENWW Manual two-sided printing 35
3.
Print side one of the document from tray 1.
4.
Gather the printed pages, and straighten the stack.
5.
Return the stack to tray 2 with the printed side down and the top edge toward the printer.
6.
Press the Go button to print side two.
36 Chapter 7 Print tasks ENWW
Print multiple pages on a single sheet of paper (N-up printing)
Use N-Up printing to place multiple document pages on a single printed page.
1.
Open the printer Properties (or Printing Preferences in Windows 2000 and XP). See Configure the
Windows printer driver on page 13
or
Configure the Macintosh printer driver on page 16 for
instructions.
2.
On the Finishing tab (the Layout tab for some Mac drivers), select the desired number of pages per sheet.
NOTE: Not all printer features are available in all drivers or operating systems. See the printer Properties (driver) online Help for information about availability of features for that driver.
3.
If desired, use the check box for page borders and the pull-down menu to specify the order of pages printed on the sheet.
ENWW Print multiple pages on a single sheet of paper (N-up printing) 37
Print booklets
You can print booklets on letter, legal, or A4 paper.
NOTE: This feature is not available for all Macintosh OS X versions.
1.
Load paper in tray 1.
2.
Close the straight-through output door.
3.
Open the printer Properties (or Printing Preferences in Windows 2000 and XP). See
Windows printer driver on page 13 for instructions.
4.
On the Finishing tab (the Paper Type/Quality tab for some Mac drivers), click to clear the Correct
Order for Straight Paper Path check box.
5.
Select the Print On Both Sides check box.
6.
Select Left Edge Binding or Right Edge Binding from the Booklet Layout drop-down list.
7.
Set the number of pages per sheet to 2 .
8.
Click OK .
9.
Print the document.
10.
Fold and staple the pages.
38 Chapter 7 Print tasks ENWW
Print watermarks
You can use the watermark option to print text "underneath" (in the background) of an existing document.
For example, you might want to have large gray letters reading Draft or Confidential printed diagonally across the first page or all of the pages of a document.
1.
Open the printer Properties (or Printing Preferences in Windows 2000 and XP). See Configure the
Windows printer driver on page 13
or
Configure the Macintosh printer driver on page 16 for
instructions.
2.
On the Effects tab (the Watermark/Overlay tab for some Mac drivers), select the watermark you want to use.
NOTE: Not all printer features are available in all drivers or operating systems. See the printer Properties (driver) online Help for information about availability of features for that driver.
ENWW Print watermarks 39
Cancel a print job
You can cancel a print job from the following locations:
● Printer control panel : To cancel the print job, press and release the Cancel button on the printer control panel.
● Software application : Typically, a dialog box appears briefly on your screen, allowing you to cancel the print job.
● Windows print queue : If a print job is waiting in a print queue (computer memory) or print spooler, delete the job there. To go to the Printer screen in Windows 98 SE, Me, 2000, or XP, click Start , click Settings , and then click Printers ; or click Start and then click Printers and Faxes . Doubleclick the printer icon to open the window. Select your print job and click Delete .
● Desktop print queue (Mac OS) : For Mac OS X, open Print Center (or Printer Setup Utility in V10.3.9), double-click the printer name, select the print job, and click Delete .
● Embedded Web server : Open the printer's embedded Web server page, and click Cancel Job .
See
Embedded Web server (network model only) on page 43
for more information.
If the status lights on the control panel continue to blink after you cancel a print job, the computer is still sending the job to the printer. Either delete the job from the print queue or wait until the computer finishes sending data. The printer will return to the Ready state.
40 Chapter 7 Print tasks ENWW
8 Managing and maintenance
This chapter provides information on the following topics:
●
●
Embedded Web server (network model only)
●
●
●
●
Clean the pickup roller (tray 1)
●
Clean the pickup roller (tray 2)
●
ENWW 41
Printer information pages
You can print the following information pages.
Demo page
The Demo page contains examples of text and graphics. To print a Demo page, do one of the following:
● Press the Go button when the printer Ready light is on and no other jobs are printing.
● Select it from the Print Information Pages drop-down list on the Services tab in Printer
Preferences .
Configuration page
The Configuration page lists current settings and properties of the printer. It also contains a status log report. To print a configuration page, do one of the following:
● Press and hold the Go button for 5 seconds when the printer Ready light is on and no other jobs are printing.
● Select it from the Print Information Pages drop-down list on the Services tab in Printer
Preferences .
Supplies Status page
You can print the Supplies Status page by selecting it from the Print Information Pages drop-down list on the Services tab in Printer Preferences . The Supplies Status page provides the following information:
● The estimated number of pages remaining on the print cartridge
● The number of pages and print jobs that have been processed
● Ordering and recycling information
42 Chapter 8 Managing and maintenance ENWW
Embedded Web server (network model only)
The embedded Web server allows you to view printer and network status and to manage printing functions from your computer instead of from the printer control panel. Below are examples of what you can do using the embedded Web server:
● View device status information
● Determine the remaining life on all supplies and order new ones
● Set the size and type of media loaded in each tray
● View and change tray configurations
● View and change the printer default configuration settings
● View and change network configuration
● You do not need to install any software on the computer. You only need to use one of these supported Web browsers:
● Internet Explorer 6.0 (and later)
● Netscape Navigator 7.0 (and later)
● Firefox 1.0 (and later)
● Mozilla 1.6 (and later)
● Opera 7.0 (and later)
● Safari 1.2 (and later)
● Konqueror 3.2 (and later)
The embedded Web server works when the printer is connected to an TCP/IP-based network. The embedded Web server does not support IPX-based connections or direct USB connections.
NOTE: You do not have to have Internet access to open and use the embedded Web server.
However, if you click a link on any of the pages, you must have Internet access in order to go to the site associated with the link.
Open the embedded Web server
To open the embedded Web server, type the IP address or hostname of the printer in the address field of a supported Web browser. To find the IP address, print a Configuration page at the printer by pressing and holding the Go button for 5 seconds when the Ready light is on and no other jobs are printing.
TIP: After you open the URL, bookmark it so that you can return to it quickly in the future.
The embedded Web server has three tabs that contain settings and information about the printer: the
Information tab, the Settings tab, and the Networking tab.
ENWW Embedded Web server (network model only) 43
Information tab
The Status pages group consists of the following pages.
● Device Status . This page displays the status of the printer and HP supplies.
● Device Configuration . This page shows the information found on the printer Configuration page.
● Supplies Status . This page shows the status of HP supplies and provides supplies part numbers.
To order new supplies, click Order Supplies in the upper-right part of the window.
● Network Summary . This page shows the information found on the printer Network Summary page.
Settings tab
This tab allows you to configure the printer from your computer. If this printer is networked, always consult with the printer administrator before changing settings on this tab.
The Settings tab contains the following pages:
● Paper Handling . View and change the settings for the printer's input tray.
● Printing . View and change the default printer job settings.
Networking tab
This tab allows the network administrator to control network-related settings for the printer when it is connected to an IP-based network.
Links
Links are located in the upper-right part of the Status pages. You must have Internet access in order to use any of these links. If you use a dial-up connection and did not connect when you first opened the embedded Web server, you must connect before you can visit these Web sites. Connecting might require that you close the embedded Web server and reopen it.
● Order Supplies . Click this link to connect to the Sure Supply Web site and order genuine
HP supplies from HP or a reseller of your choice.
● Product Support . Connects to the support site for the HP LaserJet P2010 Series printer. You can search for help regarding general topics.
44 Chapter 8 Managing and maintenance ENWW
Replace the print cartridge
1.
Press the print-cartridge-door button, and then remove the print cartridge from the printer. For recycling information, see the inside of the print-cartridge box.
2.
Remove the new print cartridge from the packaging.
3.
Bend the tab on the left side of the cartridge to break it loose.
4.
Pull the tab until all the tape is removed from the cartridge. Put the tab in the print-cartridge box to return for recycling.
ENWW Replace the print cartridge 45
5.
Gently rock the print cartridge from front to back to distribute the toner evenly inside the cartridge.
CAUTION: If toner gets on your clothing, wipe it off with a dry cloth and wash the clothing in cold water. Hot water sets toner into the fabric .
6.
Insert the print cartridge in the printer and close the print-cartridge door.
CAUTION: If toner gets on your clothing, wipe it off with a dry cloth and wash the clothing in cold water. Hot water sets toner into the fabric .
46 Chapter 8 Managing and maintenance ENWW
Redistribute toner
When toner is low, faded or light areas appear on the printed page. You might be able to temporarily improve print quality by redistributing the toner.
1.
Press the print-cartridge-door button, and then remove the print cartridge from the printer.
2.
To redistribute the toner, gently rock the print cartridge from front to back.
CAUTION: If toner gets on your clothing, wipe it off with a dry cloth and wash the clothing in cold water. Hot water sets toner into the fabric .
3.
Reinsert the print cartridge into the printer, and close the print cartridge door.
ENWW
instructions.
Redistribute toner 47
Clean the printer
Clean the outside of the printer with a clean, damp cloth when necessary.
CAUTION: Do not use ammonia-based cleaners on or around the printer.
During the printing process, paper, toner, and dust particles can accumulate inside the printer. Over time, this buildup can cause print quality problems, such as toner specks or smearing, and paper jams.
To correct and prevent these types of problems, you can clean the print cartridge area and the printer media path.
Clean the print-cartridge area
You do not need to clean the print-cartridge area often. However, cleaning this area can improve the quality of your printed sheets.
WARNING!
Before cleaning the printer, turn the printer off by unplugging the power cord, and wait for the printer to cool.
1.
Press the print-cartridge-door button, and then remove the print cartridge from the printer.
CAUTION: Do not touch the black sponge-transfer roller inside the printer. Doing so can damage the printer.
CAUTION: To prevent damage, do not expose the print cartridge to light. Cover it with a piece of paper.
48 Chapter 8 Managing and maintenance ENWW
2.
With a dry, lint-free cloth, wipe any residue from the media-path area and the print-cartridge cavity.
3.
Replace the print cartridge, and close the print-cartridge door.
4.
Plug the printer in to turn it back on.
5.
Verify printer functionality by printing a demo page. To print a demo page, press the Go button when the Ready light is on and no other jobs are printing.
Clean the printer media path
If you are experiencing toner specks or dots on the printouts, clean the printer media path. This process uses a transparency to remove dust and toner from the media path. Do not use bond or rough paper.
ENWW Clean the printer 49
NOTE: For best results use a sheet of transparency. If you do not have any transparencies, you can use copier grade media (70 to 90 g/m 2 (18 to 24 lb.)) with a smooth surface.
1.
Make sure that the printer is idle and the Ready light is on.
2.
Load the transparency in tray 1.
3.
Print a cleaning page. Open the printer Properties screen (or Printing Preferences screen in
Windows 2000 and XP) and select the cleaning page.
NOTE: The cleaning process takes approximately 2 minutes. The cleaning page will stop periodically during the cleaning process. Do not turn the printer off until the cleaning process has finished. You might need to repeat the cleaning process several times to thoroughly clean the printer.
50 Chapter 8 Managing and maintenance ENWW
Clean the pickup roller (tray 1)
If you want to clean the pickup roller for tray 1, follow these instructions:
1.
Unplug the power cord from the printer, and allow the printer to cool.
2.
Press the print-cartridge-door button, and then remove the print cartridge from the printer.
CAUTION: Do not touch the black sponge-transfer roller inside the printer. Doing so can damage the printer.
CAUTION: To prevent damage, do not expose the print cartridge to light. Cover it with a piece of paper.
ENWW Clean the pickup roller (tray 1) 51
3.
Remove the pickup roller cover.
4.
Press the two black retaining tabs outward until the pickup roller is released from its seat.
5.
Remove the pickup roller from the printer.
52 Chapter 8 Managing and maintenance ENWW
ENWW
6.
Dab a lint-free cloth in water, and scrub the roller.
NOTE: Do not touch the surface of the roller with bare fingers.
7.
Using a dry, lint-free cloth, wipe the pickup roller to remove loosened dirt.
8.
Allow the pickup roller to dry completely.
9.
Line up the black retaining tabs in the printer with the grooves in the pickup roller, and then press the pickup roller into the pickup roller seat until the retaining tabs click.
Clean the pickup roller (tray 1) 53
10.
Replace the pickup roller cover.
11.
Reinstall the print cartridge, and close the print-cartridge door.
12.
Plug the printer in to turn it back on.
13.
Verify printer functionality by printing a demo page. To print a demo page, press the Go button when the Ready light is on and no other jobs are printing.
54 Chapter 8 Managing and maintenance ENWW
Clean the pickup roller (tray 2)
If you want to clean the pickup roller for tray 2, follow these instructions:
1.
Unplug the power cord from the printer, and allow the printer to cool.
2.
Press the print-cartridge-door button, and then remove the print cartridge from the printer.
CAUTION: Do not touch the black sponge-transfer roller inside the printer. Doing so can damage the printer.
CAUTION: To prevent damage, do not expose the print cartridge to light. Cover it with a piece of paper.
ENWW Clean the pickup roller (tray 2) 55
3.
Remove tray 2.
4.
Place the printer on the work surface with the front of the printer facing up.
56 Chapter 8 Managing and maintenance ENWW
5.
Pull the white tabs outward, and rotate the tabs up.
6.
Slide the right tab to the right, and leave the tab in this position throughout the procedure.
ENWW Clean the pickup roller (tray 2) 57
7.
Slide the pickup roller assembly to the right, and remove the left end cap.
8.
Remove the pickup roller.
58 Chapter 8 Managing and maintenance ENWW
ENWW
9.
Dab a lint-free cloth in water, and scrub the roller.
NOTE: Do not touch the surface of the roller with bare fingers.
10.
Using a dry, lint-free cloth, wipe the pickup roller to remove loosened dirt.
11.
Allow the pickup roller to dry completely.
12.
Insert the left side of the pickup roller into the left slot (1), and insert the right side (the side that has the notches in the shaft) into the right slot (2).
Clean the pickup roller (tray 2) 59
13.
Place the end cap over the shaft on the left side, push the end cap to the right, and rotate the tab downward into position.
14.
Rotate the shaft until the notches engage and the shaft clicks into place.
15.
Push the right tab to the left, and rotate the tab downward into position.
16.
Place the printer on the work surface with the top of the printer facing up.
17.
Close the automatic two-sided path door.
60 Chapter 8 Managing and maintenance ENWW
18.
Reinstall the print cartridge, and close the print-cartridge door.
19.
Plug the printer in to turn it back on.
20.
Verify printer functionality by printing a demo page. To print a demo page, press the Go button when the Ready light is on and no other jobs are printing.
ENWW Clean the pickup roller (tray 2) 61
EconoMode
EconoMode is a feature that allows the printer to use less toner per page. Selecting this option may extend the life of the print cartridge and reduce your cost per page. However, it will also reduce print quality. The printed image is lighter, but it is adequate for printing drafts or proofs.
HP does not recommend the full-time use of EconoMode. If EconoMode is used full-time, it is possible that the toner supply will outlast the mechanical parts in the print cartridge. If print quality begins to degrade under these circumstances, you must install a new print cartridge, even if toner supply remains in the cartridge.
1.
To use EconoMode, open the printer Properties (or Printing Preferences in Windows 2000 and XP).
See
Configure the Windows printer driver on page 13 or
Configure the Macintosh printer driver on page 16 for instructions.
2.
On the Paper/Quality tab or the Finishing tab (the Paper Type/Quality tab for some Mac drivers), select the EconoMode checkbox.
NOTE: Not all printer features are available in all drivers or operating systems. See the printer
Properties (driver) online Help for information about availability of features for that driver.
62 Chapter 8 Managing and maintenance ENWW
9 Problem solving
This chapter provides information on the following topics:
●
●
●
●
●
Printed page is different than what appeared on screen
●
●
●
●
ENWW 63
Finding the solution
You can use this section to find the solution to common printer problems.
Step 1: Is the printer set up correctly?
● Is the printer plugged into a power outlet that is known to work?
● Is the on/off switch in the on position?
● Is the print cartridge properly installed? See
Replace the print cartridge on page 45 .
● Is paper properly loaded in the input tray? See
.
Yes
No
If you answered yes to the questions above, go to Step 2: Is the Ready light on? on page 64 .
If the printer will not turn on,
Contact HP support on page 66 .
Step 2: Is the Ready light on?
Verify that the Ready light (1) is illuminated on the control panel.
Yes
No
64 Chapter 9 Problem solving
Go to
Step 3: Can you print a demo page? on page 65
.
If the control panel lights do not look like the picture above, see
Status-light patterns on page 67
.
If you are unable to resolve the problem, Contact
.
ENWW
Step 3: Can you print a demo page?
Press the Go button when the device Ready light is on and no other jobs are printing to print a demo page.
Yes
No
If the demo page printed, go to Step 4: Is the print quality acceptable? on page 65
.
If no paper came out, see
Media problem solving on page 77 .
If you are unable to resolve the problem, Contact
Step 4: Is the print quality acceptable?
Yes
No
If the print quality is acceptable, go to
Step 5: Is the printer communicating with the computer? on page 65 .
If the print quality is poor, see
Improve print quality on page 82 .
Verify that the print settings are correct for the media you are using. See
Media type and tray loading on page 28
for information about adjusting the settings for various types of media.
If you are unable to resolve the problem, Contact
Step 5: Is the printer communicating with the computer?
Try printing a document from a software application.
Yes
No
If the document prints, go to Step 6: Does the printed page look like you expected? on page 65
.
If the document does not print, see Printer software problems on page 81
.
If you are using a Macintosh computer, see Common
Macintosh problems on page 74 .
If you are unable to resolve the problem, Contact
Step 6: Does the printed page look like you expected?
Yes
No
The problem should be resolved. If it is not resolved, Contact
See
Printed page is different than what appeared on screen on page 79 .
If you are unable to resolve the problem, Contact
ENWW Finding the solution 65
Contact HP support
● In the United States, see http://www.hp.com/go/support/ljP2010series for support.
● In other locations, see http://www.hp.com/ .
66 Chapter 9 Problem solving ENWW
Status-light patterns
ENWW
Table 9-1 Status-light legend
Symbol for "light off"
Symbol for "light on"
Symbol for "light blinking"
Table 9-2 Control-panel light messages
Light status State of the printer Action
Initialization/Startup
While in the Startup state, the Go, Ready, and Attention lights cycle (at the rate of
500 ms) one after another.
During the Initialization, Reconfiguration, and Job Cancel processes, pressing buttons has no effect.
Reconfiguration Initialization
During the printer start up, you can request special initialization sequences that reconfigure the printer. When one of the sequences is requested, such as cold reset, the lights cycle as in the
Initialization/Startup state.
Job Cancel
After the cancellation process has been completed, the printer returns to the
Ready state.
Status-light patterns 67
Table 9-2 Control-panel light messages (continued)
Light status State of the printer
Ready
The printer is ready with no job activity.
Action
To print a Configuration page, press and hold the Go button for 5 seconds while the device Ready light is on and no other jobs are printing.
Processing Data
The printer is processing or receiving data.
To cancel the current job, press the
Cancel button.
68 Chapter 9 Problem solving ENWW
Table 9-2 Control-panel light messages (continued)
Light status State of the printer Action
Manual Feed or Continuable Error
This state can be reached in the following circumstances:
To recover from the error and print whatever data is possible, press the Go button.
● Manual feed
If the recovery is successful, the printer goes to the Processing Data state and completes the job.
● General continuable error
● Memory configuration error
If the recovery is unsuccessful, the printer returns to the Continuable Error state.
● Personality/Job related error
Attention
The print-cartridge door is open.
Close the print-cartridge door.
ENWW Status-light patterns 69
Table 9-2 Control-panel light messages (continued)
Light status State of the printer
Fatal Error
Action
● Turn off the printer, wait 10 seconds, and turn on the printer.
● If you are unable to resolve the
problem, Contact HP support on page 66 .
Accessory Error To display additional error information, press the Go button. The light pattern changes. For more information about the light pattern now displayed, see
9-3 Accessory error indicators on page 73 . When you release the
Go button, the printer returns to the initial
Accessory Error state.
70 Chapter 9 Problem solving ENWW
Table 9-2 Control-panel light messages (continued)
Light status State of the printer
Toner Low
The Go, Ready, and Attention lights act independently of the Toner Low state.
Action
Order a new print cartridge and have it ready. See
Supplies and accessories table on page 97
.
Toner Missing
The print cartridge has been removed from the printer.
Reinsert the print cartridge in the printer.
ENWW Status-light patterns 71
Table 9-2 Control-panel light messages (continued)
Light status State of the printer
Jam
Action
Clear the jam. See
72 Chapter 9 Problem solving ENWW
Table 9-2 Control-panel light messages (continued)
Light status State of the printer
Paper Out
Action
Load paper or other media.
Paper Mount
The loaded paper or other media is not supported.
Load acceptable paper or other media.
Press the Go button to override the condition.
ENWW
Table 9-3 Accessory error indicators
Accessory error Attention light
DIMM slot incompatible error Off
Ready light
Off
Go light
On
Status-light patterns 73
Common Macintosh problems
This section lists problems that can occur when using Mac OS X.
Table 9-4 Problems with Mac OS X
The printer driver is not listed in the Print Center or Printer Setup Utility.
Cause
The printer software might not have been installed or was installed incorrectly.
The PostScript Printer Description (PPD) file is corrupt.
Solution
Make sure that the printer PPD is in the following hard-drive folder:
Library/Printers/PPDs/Contents/Resources/
<lang>.lproj
, where <lang> is the two-letter language code for the language that you are using. If necessary, reinstall the software.
See the Getting Started Guide for instructions.
Delete the PPD file from the following hard-drive folder: Library/
Printers/PPDs/Contents/Resources/<lang>.lproj
, where <lang> is the two-letter language code for the language that you are using. Reinstall the software. See the Getting Started
Guide for instructions.
The printer name, IP address, or Rendezvous or Bonjour host name does not appear in the printer list in the Print Center or Printer
Setup Utility.
Cause Solution
The printer might not be ready.
The wrong connection type might be selected.
Make sure that the cables are connected correctly, the printer is on, and the ready light is on. If you are connecting through a USB or
Ethernet hub, try connecting directly to the computer or use a different port.
Make sure that USB, IP Printing, or Rendezvous or Bonjour is selected, depending on the type of connection that exists between the printer and the computer.
The wrong printer name, IP address, or Rendezvous or Bonjour host name is being used.
Print a configuration page to check the printer name, IP address, or
Rendezvous or Bonjour host name. Verify that the name, IP address, or Rendezvous or Bonjour host name on the configuration page matches the printer name, IP address, or Rendezvous or Bonjour host name in the Print Center or Printer Setup Utility.
The interface cable might be defective or of poor quality.
Replace the interface cable. Make sure to use a high-quality cable.
The printer driver does not automatically set up your selected printer in the Print Center or Printer Setup Utility.
Cause Solution
The printer might not be ready.
The printer software might not have been installed or was installed incorrectly.
Make sure that the cables are connected correctly, the printer is on, and the ready light is on. If you are connecting through a USB or
Ethernet hub, try connecting directly to the computer or use a different port.
Make sure that the printer PPD is in the following hard-drive folder:
Library/Printers/PPDs/Contents/Resources/
<lang>.lproj
, where <lang> is the two-letter language code for the language that you are using. If necessary, reinstall the software.
See the Getting Started Guide for instructions.
74 Chapter 9 Problem solving ENWW
Table 9-4 Problems with Mac OS X (continued)
The printer driver does not automatically set up your selected printer in the Print Center or Printer Setup Utility.
Cause
The PostScript Printer Description (PPD) file is corrupt.
The printer might not be ready.
The interface cable might be defective or of poor quality.
Solution
Delete the PPD file from the following hard-drive folder: Library/
Printers/PPDs/Contents/Resources/<lang>.lproj
, where <lang> is the two-letter language code for the language that you are using. Reinstall the software. See the Getting Started
Guide for instructions.
Make sure that the cables are connected correctly, the printer is on, and the ready light is on. If you are connecting through a USB or
Ethernet hub, try connecting directly to the computer or use a different port.
Replace the interface cable. Make sure to use a high-quality cable.
A print job was not sent to the printer that you wanted.
Cause Solution
The print queue might be stopped.
Restart the print queue. Open print monitor and select Start Jobs .
The wrong printer name or IP address is being used. Another printer with the same or similar name, IP address, or Rendezvous or Bonjour host name might have received your print job.
Print a configuration page to check the printer name, IP address, or
Rendezvous or Bonjour host name. Verify that the name, IP address, or Rendezvous or Bonjour host name on the configuration page matches the printer name, IP address, or Rendezvous or Bonjour host name in the Print Center or Printer Setup Utility.
You are unable to print from a third-party USB card.
Cause
This error occurs when the software for USB printers is not installed.
Solution
When adding a third-party USB card, you might need the Apple USB
Adapter Card Support software. The most current version of this software is available from the Apple Web site.
When connected with a USB cable, the printer does not appear in the Print Center or Printer Setup Utility after the driver is selected.
Cause Solution
This problem is caused by either a software or a hardware component.
Software troubleshooting
● Check that your Macintosh supports USB.
● Verify that your Macintosh operating system is Mac OS X v10.2
or later.
● Ensure that your Macintosh has the appropriate USB software from Apple.
Hardware troubleshooting
● Check that the printer is turned on.
● Verify that the USB cable is connected correctly.
● Check that you are using the appropriate high-speed USB cable.
ENWW Common Macintosh problems 75
Table 9-4 Problems with Mac OS X (continued)
When connected with a USB cable, the printer does not appear in the Print Center or Printer Setup Utility after the driver is selected.
Cause Solution
● Ensure that you do not have too many USB devices drawing power from the chain. Disconnect all of the devices from the chain, and connect the cable directly to the USB port on the host computer.
● Check to see if more than two nonpowered USB hubs are connected in a row on the chain. Disconnect all of the devices from the chain and connect the cable directly to the USB port on the host computer.
NOTE: The iMac keyboard is a nonpowered USB hub.
76 Chapter 9 Problem solving ENWW
Media problem solving
The following problems with media cause print-quality deviations, jamming, or damage to the printer.
Problem Cause Solution
Poor print quality or toner adhesion
Dropouts, jamming, or curl
Excessive curl
Jamming, damage to printer
The printer does not pull media from media input tray when using the automatic two-sided printing feature.
The paper is too moist, too rough, too heavy or too smooth, or it is embossed or from a faulty paper lot.
The paper varies from side-to-side.
The paper has cutouts or perforations.
Try another kind of paper, between 100 and 250 Sheffield, with 4 to 6% moisture content.
The paper has been stored incorrectly.
Store paper flat in its moisture-proof wrapping.
Turn the paper over.
The paper has variability from one side to the other.
The paper is too moist, has the wrong grain direction, or is of short-grain construction
Open the rear output bin, or use longgrain paper.
Turn the paper over.
Use paper that is free of cutouts or perforations.
Problems with feeding
Print is skewed (crooked).
More than one sheet feeds at one time.
The paper has ragged edges.
The media tray might be overloaded.
Use high-quality paper that is made for laser printers.
Turn the paper over.
The paper varies from side-to-side.
The paper is too moist, too rough, too heavy or too smooth, has the wrong grain direction, or is of short-grain construction or it is embossed or from a faulty paper lot.
Try another kind of paper, between 100 and 250 Sheffield, 4 to 6% moisture content.
Open the rear output bin, or use longgrain paper.
The media guides might be incorrectly adjusted.
Remove all media from the input tray, straighten the stack, and then load the media in the input tray again. Adjust the media guides to the width and length of the media that you are using and try printing again.
Remove some of the media from the tray.
.
The printer does not pull media from the media input tray.
The media might be wrinkled, folded, or damaged.
The printer might be in manual-feed mode.
Verify that the media is not wrinkled, folded, or damaged. Try printing on media from a new or different package.
Verify that the printer is not in manual feed mode and print your job again.
The pickup roller might be dirty or damaged.
Contact HP Customer Care. See
or the support flyer that came in the box.
The paper-length adjustment control in tray 2 or optional tray 3 is set at a length that is greater than the media size.
Adjust the paper-length adjustment control to the correct length.
The automatic two-sided printing mediasize selector is not set to the correct page size.
Push in the media selector for letter/ legal-size media. Pull out the media-size selector for A4–size media. See
Identify product parts on page 3
for the location
ENWW Media problem solving 77
Problem Cause Solution of the automatic two-sided printing media-size selector.
78 Chapter 9 Problem solving ENWW
Printed page is different than what appeared on screen
Choose the item that best describes the problem:
●
Garbled, incorrect, or incomplete text on page 79
●
Missing graphics or text, or blank pages on page 79
●
Page format is different than on another HP LaserJet printer on page 80
●
Garbled, incorrect, or incomplete text
● The wrong printer driver might have been selected when the software was installed. Make sure that the correct print driver is selected in the printer Properties.
● If a specific file prints garbled text, there might be a problem with that specific file. If a specific application prints garbled text, there might be a problem with that application. Make sure that the appropriate printer driver is selected.
● There might be a problem with your software application. Try printing from another software application.
● The USB cable might be loose or defective. Try the following:
● Disconnect the cable and reconnect it at both ends.
● Try printing a job that you know works.
● If possible, attach the cable and printer to another computer, and try printing a job that you know works.
●
● Turn off the printer and the computer. Remove the USB cable, and inspect both ends of the cable for damage. Reconnect the cable, making sure that the connections are tight. Make sure that the printer is directly connected to the computer. Remove any switchboxes, tape backup drives, security keys, or any other devices that are attached between the USB port on the computer and the printer. These devices can sometimes interfere with communication between the computer and the printer. Restart the printer and the computer.
Missing graphics or text, or blank pages
● Make sure that your file does not contain blank pages.
● The sealing tape might still be in the print cartridge. Remove the print cartridge, and pull the tab on the end of the cartridge until the entire length of the tape is removed. Reinstall the print cartridge.
See Replace the print cartridge on page 45
for instructions. To check the printer, print a demo page by pressing the Go button when the Ready light is on and no other jobs are printing.
● The graphic settings in the printer Properties might not be correct for the type of job that you are printing. Try a different graphic setting in the printer Properties. See
Configure the Windows printer driver on page 13 or
Configure the Macintosh printer driver on page 16
for more information.
● Clean the printer, particularly the contacts between the print cartridge and the power supply.
ENWW Printed page is different than what appeared on screen 79
Page format is different than on another HP LaserJet printer
If you used an older or different HP LaserJet printer driver (printer software) to create the document, or if the printer Properties settings in the software are different, the page format might change when you try to print using your new printer driver or settings. To help eliminate this problem, try the following:
● Create documents and print them using the same printer driver (printer software) and printer
Properties settings regardless of which HP LaserJet printer you use to print them.
● Change the resolution, paper size, font settings, and other settings. See
Configure the Windows printer driver on page 13
or Configure the Macintosh printer driver on page 16 for more information.
Graphics quality
The graphics settings might be unsuitable for your print job. Check the graphic settings, such as resolution, in the printer Properties and adjust them as necessary. See
Configure the Windows printer driver on page 13 or
Configure the Macintosh printer driver on page 16
for more information.
NOTE: Some resolution may be lost when converting from one graphics format to another.
80 Chapter 9 Problem solving ENWW
Printer software problems
Table 9-5 Printer software problems
Problem
The printer icon is not visible in the Printer folder
An error message was displayed during the software installation
The printer is in Ready mode, but nothing prints
Solution
● Reinstall the printer software. In the Windows task bar, click Start , click Programs , click HP , click your printer, and then click Uninstall . Install the printer software from the CD-ROM.
NOTE: Close any applications that are running. To close an application that has an icon in the system tray, right-click the icon, and select Close or Disable .
● Try plugging the USB cable into a different USB port on the PC.
● Reinstall the printer software. In the Windows task bar, click Start , click Programs , click HP , click your printer, and then click Uninstall . Install the printer software from the CD-ROM.
NOTE: Close any applications that are running. To close an application that has an icon in the task bar, right-click the icon, and select
Close or Disable .
● Check the amount of free space on the drive where you are installing the printer software. If necessary, free up as much space as you can, and reinstall the printer software.
● If necessary, run the Disk Defragmenter, and reinstall the printer software.
● Print a Configuration page from the control panel of the printer, and verify the printer functionality.
● Verify that all of the cables are properly seated and within specifications. This includes the USB, network, and power cables. Try a new cable.
ENWW Printer software problems 81
Improve print quality
This section provides information about identifying and correcting print defects.
NOTE: If these steps do not correct the problem, contact an HP-authorized dealer or service representative.
Light print or faded
● The print cartridge is nearing end of life.
● The media might not meet Hewlett-Packard's media specifications (for example, the media is too moist or too rough).
● If the whole page is light, the print density adjustment is too light or EconoMode might be turned on. Adjust the print density, and disable EconoMode in the printer
Properties.
Toner specks
● The media might not meet Hewlett-Packard's media specifications (for example, the media is too moist or too rough).
● The printer might need to be cleaned.
Dropouts
● A single sheet of media might be defective. Try reprinting the job.
● The media moisture content is uneven or the media has moist spots on its surface. Try printing with new media.
● The media lot is bad. The manufacturing processes can cause some areas to reject toner. Try a different type or brand of media.
● The print cartridge might be defective.
82 Chapter 9 Problem solving ENWW
Vertical lines
Gray background
Toner smear
Loose toner
ENWW
The photosensitive drum inside the print cartridge has probably been scratched. Install a new HP print cartridge.
● Make sure that tray 1 is in place.
● Change the media to a lighter basis weight.
● Check the printer's environment. Very dry (low humidity) conditions can increase the amount of background shading.
● Install a new HP print cartridge.
● If toner smears appear on the leading edge of the media, the media guides might be dirty. Wipe the media guides with a dry, lint-free cloth.
● Check the media type and quality.
● Try installing a new HP print cartridge.
● The fuser temperature might be too low. In your printer driver, make sure the appropriate media type is selected.
● Clean the inside of the printer.
● Check the media type and quality.
● Try installing a new HP print cartridge.
● In your printer driver, make sure the appropriate media type is selected.
● Plug the printer directly into an AC outlet instead of into a power strip.
Improve print quality 83
Vertical repetitive defects
Misformed characters
Page skew
Curl or wave
84 Chapter 9 Problem solving
● The print cartridge might be damaged. If a repetitive mark occurs at the same spot on the page, install a new
HP print cartridge.
● The internal parts might have toner on them. If the defects occur on the back of the page, the problem will probably correct itself after a few more printed pages.
● In your printer driver, make sure the appropriate media type is selected.
● If characters are improperly formed, producing hollow images, the media stock might be too slick. Try a different media.
● If characters are improperly formed, producing a wavy effect, the printer might need service. Print a configuration page. If the characters are improperly formed, contact an
HP-authorized dealer or service representative.
● Make sure that the media is loaded correctly and the media guides are not too tight or too loose against the media stack.
● The input bin might be too full.
● Check the media type and quality.
● Check the media type and quality. Both high temperature and high humidity cause media to curl.
● The media might have been in the input tray too long.
Turn over the stack of media in the tray. Also, try rotating the media 180° in the input tray.
● Open the straight-through output door and try printing straight through.
● The fuser temperature might be too high. In your printer driver, make sure the appropriate media type is selected.
If the problem persists, select a media type that uses a
ENWW
Wrinkles or creases
Toner scatter outline
lower fuser temperature, such as transparencies or light media.
● Make sure that media is loaded properly.
● Check the media type and quality.
● Open the straight-through output door and try printing straight through.
● Turn over the stack of media in the tray. Also, try rotating the media 180° in the input tray.
● For envelopes, this can be caused by air pockets inside the envelope. Remove the envelope, flatten the envelope, and try printing again.
● If large amounts of toner have scattered around the characters, the media might be resisting the toner. (A small amount of toner scatter is normal for laser printing.)
Try a different media type.
● Turn over the stack of media in the tray.
● Use media that is designed for laser printers.
ENWW Improve print quality 85
Clear jams
Occasionally, media becomes jammed during a print job. You are notified of a media jam by an error in the software and the printer control panel lights. See
Status-light patterns on page 67 for more
information.
The following are some of the causes of media jams:
●
The input trays are loaded improperly or too full. See Load media on page 24 for more information.
NOTE: When you add new media, always remove all of the media from the input tray and straighten the stack of new media. This helps prevent multiple sheets of media from feeding through the printer at one time, reducing media jams.
●
● The printer might need to be cleaned to remove paper dust and other particles from the paper path.
See
for instructions.
There might be loose toner in the printer after a media jam. This toner clears up after a few sheets print.
CAUTION: Media jams might result in loose toner on the page. If you get any toner on your clothes, wash them in cold water. Hot water will permanently set the toner into the fabric.
CAUTION: Do not use sharp objects, such as tweezers or needlenose pliers, to remove jams.
Damage caused by sharp objects is not covered by the warranty.
Print-cartridge area
To clear a jam in the print-cartridge area, perform the following steps:
1.
Press the print-cartridge-door button, and then remove the print cartridge from the printer.
CAUTION: To prevent damage to the print cartridge, minimize its exposure to direct light.
86 Chapter 9 Problem solving ENWW
ENWW
2.
Open the straight-through output door.
3.
Pull down the green pressure-release levers.
4.
With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the printer.
Clear jams 87
5.
Replace the print cartridge, and close the print-cartridge door.
Input trays
To clear a jam in the input trays, perform the following steps:
1.
Open the straight-through output door.
2.
Pull down the green pressure-release levers.
88 Chapter 9 Problem solving ENWW
ENWW
3.
Press the print-cartridge-door button, and then remove the print cartridge from the printer.
4.
With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the printer.
5.
Insert the print cartridge in the printer and close the print-cartridge door.
Clear jams 89
6.
Open tray 2.
7.
With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the printer.
90 Chapter 9 Problem solving ENWW
8.
If no media is visible, open the print-cartridge door, remove the print cartridge, and pull down the upper media guide. Carefully pull the media up and out of the printer.
9.
Close tray 2.
Output bin
With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the printer.
ENWW Clear jams 91
Straight-through output path
To clear a jam in the straight-through output path, perform the following steps:
1.
Open the straight-through output door.
2.
Pull down the green pressure-release levers.
92 Chapter 9 Problem solving ENWW
3.
With both hands, grasp the side of the media that is most visible (this includes the middle), and carefully pull it free from the printer.
NOTE: If you cannot grasp the media with your hands, perform the procedure in
Printcartridge area on page 86 .
4.
Close the straight-through output door.
ENWW Clear jams 93
Network-setup problem-solving
If the computer cannot discover the networked device, perform the following steps:
1.
Check the cables to ensure that they are properly connected. Check all of the following connections:
● Power cables
● Cables between the device and the hub or switch
● Cables between the hub or switch and the computer
● Cables to and from the modem or Internet connection, if applicable
2.
Verify that the computer's network connections are working properly (Windows only):
● On the Windows desktop, double-click My Network Places or Network Neighborhood .
● Click the Entire Network link.
● Click the Entire Contents link.
● Double-click one of the network icons, and make sure that some devices are listed.
3.
Verify that the network connection is active:
● Check the network light on the network (RJ-45) connector on the back of the device.
● If one of the lights is on solid, the device is connected to the network.
● If both network lights are off, check the cable connections from the device to the gateway, switch, or hub to ensure that the connections are secure.
● If the connections are secure, turn off the power to the device for at least 10 seconds, and then turn on the power to the device.
4.
Print a Configuration page. See
Configuration page on page 42 .
● On the Configuration page, see if a non-zero IP address is assigned to the device.
● If the Configuration page does not have a valid, non-zero IP address, reset the HP internal network port to the factory defaults by turning the printer off and then pressing and holding the Go and Cancel buttons at the same time for ten seconds while powering the printer back on.
After the Attention, Ready, and Go lights finish cycling, the device returns to a Ready state and the reset is complete.
● Two minutes after the device reaches the Ready state, print another Configuration page, and check to see if a valid IP address is assigned to the device.
● If the IP address is still zeros, contact HP support. See
HP Customer Care on page 105 .
94 Chapter 9 Problem solving ENWW
A Accessory/Consumable addendum
This appendix provides information on the following topics:
●
Order parts, accessories, and supplies
●
Supplies and accessories table
●
10/100 networking print servers
●
ENWW 95
Order parts, accessories, and supplies
●
●
Order through service or support providers
●
Order directly through the embedded Web server
Order directly from HP
You can obtain the following directly from HP:
● Replacement parts . To order replacement parts in the U.S. see http://www.hp.com/buy/parts .
Outside the United States, order parts by contacting your local authorized HP service center.
● Supplies and accessories . To order supplies in the U.S., see http://www.hp.com/go/ljsupplies .
To order supplies worldwide, see http://www.hp.com/ghp/buyonline.html
. To order accessories, see http://www.hp.com/go/support/ljP2010series .
Order through service or support providers
To order a part or accessory, contact an HP-authorized service or support provider.
Order directly through the embedded Web server
1.
In the Web browser on the computer, type the IP address for the MFP. The MFP status window appears.
2.
In the Other links area, double-click Order Supplies . This provides a URL from which to purchase consumables. Supplies information with part numbers and MFP information is provided.
3.
Select the part numbers that you want to order and follow the instructions on the screen.
96 Appendix A Accessory/Consumable addendum ENWW
Supplies and accessories table
You can increase the printer's capabilities with optional accessories and supplies. Use accessories and supplies specifically designed for the product to ensure optimum performance.
Table A-1 Ordering information
Item Description or use Order number
Print cartridges for the product Smart print cartridges Replacement print cartridges for the product.
Supplementary documentation
HP LaserJet family print media guide
A guide to using paper and other print media with
HP LaserJet printers.
Q7553A (3,000-page cartridge)
Q7553X (7,000-page cartridge)
5963-7863
NOTE: This document can be downloaded from http://www.hp.com/ support/ ljpaperguide/ .
Replacement parts
Accessories
Media pickup roller (for tray 1) Picks media from tray 1 and advances it through the printer.
Media pickup roller (for tray 2) Picks media from tray 2 and advances it through the printer.
250-sheet paper tray (tray 3) Provides an additional 250sheet input tray.
CB366-67901
CB366-67902
Q5931A
ENWW Supplies and accessories table 97
10/100 networking print servers
Table A-2 HP LaserJet P2010 Series printer
Item and description Order number
HP Jetdirect en3700 fast Ethernet print server J7942A
HP Jetdirect en2400 802.11g wireless external print server (full featured, USB port)
J7951A
J6035C HP Jetdirect 175x fast-Ethernet external print server (value line, USB port)
Must be Version C or later.
98 Appendix A Accessory/Consumable addendum ENWW
HP print cartridges
HP policy on non-HP print cartridges
Hewlett-Packard Company cannot recommend the use of non-HP print cartridges, either new, refilled, or remanufactured. Service or repair that is required as a result of using non-HP print cartridges will not be covered under the printer warranty.
NOTE: The warranty does not apply to defects resulting from software, interfacing, or parts not supplied by Hewlett-Packard.
Storing print cartridges
Do not remove the print cartridge from its package until you are ready to use it, and minimize exposure to light.
Print cartridge life expectancy
The average cartridge yield is 3000 pages in accordance with ISO/IEC 19752. Actual cartridge yield depends on specific use.
Saving toner
EconoMode is a feature that allows the printer to use less toner per page. Selecting this option may extend the life of the print cartridge and reduce your cost per page. However, it will also reduce print quality. The printed image is lighter, but it is adequate for printing drafts or proofs.
HP does not recommend the full-time use of EconoMode. If EconoMode is used full-time, it is possible that the toner supply will outlast the mechanical parts in the print cartridge. If print quality begins to degrade under these circumstances, you must install a new print cartridge, even if there is toner supply remaining in the cartridge. See
EconoMode on page 62 for more information.
ENWW HP print cartridges 99
100 Appendix A Accessory/Consumable addendum ENWW
B Service and support
ENWW 101
Hewlett-Packard limited warranty statement
HP PRODUCT
HP LaserJet P2010 Series printers
DURATION OF LIMITED WARRANTY
One year from date of purchase
HP warrants to you, the end-user customer, that HP hardware and accessories will be free from defects in materials and workmanship after the date of purchase, for the period specified above. If HP receives notice of such defects during the warranty period, HP will, at its option, either repair or replace products which prove to be defective.
Replacement products may be either new or equivalent in performance to new.
HP warrants to you that HP software will not fail to execute its programming instructions after the date of purchase, for the period specified above, due to defects in material and workmanship when properly installed and used. If
HP receives notice of such defects during the warranty period, HP will replace software which does not execute its programming instructions due to such defects.
HP does not warrant that the operation of HP products will be uninterrupted or error free. If HP is unable, within a reasonable time, to repair or replace any product to a condition as warranted, you will be entitled to a refund of the purchase price upon prompt return of the product.
HP products may contain remanufactured parts equivalent to new in performance or may have been subject to incidental use.
Warranty does not apply to defects resulting from (a) improper or inadequate maintenance or calibration,
(b) software, interfacing, parts or supplies not supplied by HP, (c) unauthorized modification or misuse,
(d) operation outside of the published environmental specifications for the product, or (e) improper site preparation or maintenance.
HP's limited warranty is valid in any country/region or locality where HP has a support presence for this product and where HP has marketed this product. The level of warranty service you receive may vary according to local standards. HP will not alter form, fit or function of the product to make it operate in a country/region for which it was never intended to function for legal or regulatory reasons. TO THE EXTENT ALLOWED BY LOCAL LAW,
THE ABOVE WARRANTIES ARE EXCLUSIVE AND NO OTHER WARRANTY OR CONDITION, WHETHER
WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED AND HP SPECIFICALLY DISCLAIMS ANY IMPLIED
WARRANTIES OR CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY, AND FITNESS FOR A
PARTICULAR PURPOSE. Some countries/regions, states or provinces do not allow limitations on the duration of an implied warranty, so the above limitation or exclusion might not apply to you. This warranty gives you specific legal rights and you might also have other rights that vary from country/region to country/region, state to state, or province to province.
TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY STATEMENT ARE YOUR
SOLE AND EXCLUSIVE REMEDIES. EXCEPT AS INDICATED ABOVE, IN NO EVENT WILL HP OR ITS
SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL
(INCLUDING LOST PROFIT OR DATA), OR OTHER DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR
OTHERWISE. Some countries/regions, states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT LAWFULLY
PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION TO THE MANDATORY
STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU.
102 Appendix B Service and support ENWW
Limited warranty for print cartridges and image drums
This HP Print Cartridge is warranted to be free from defects in materials and workmanship.
This warranty does not apply to print cartridges that (a) have been refilled, refurbished, remanufactured or tampered with in any way, (b) experience problems resulting from misuse, improper storage, or operation outside of the published environmental specifications for the printer product or (c) exhibit wear from ordinary use.
To obtain warranty service, please return the product to place of purchase (with a written description of the problem and print samples) or contact HP customer support. At HP’s option, HP will either replace products that prove to be defective or refund your purchase price.
TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTY IS EXCLUSIVE AND NO
OTHER WARRANTY OR CONDITION, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR
IMPLIED AND HP SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY, SATISFACTORY QUALITY, AND FITNESS FOR A PARTICULAR PURPOSE.
TO THE EXTENT ALLOWED BY LOCAL LAW, IN NO EVENT WILL HP OR ITS SUPPLIERS BE
LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT OR
DATA), OR OTHER DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT
LAWFULLY PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION TO
THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU.
ENWW Limited warranty for print cartridges and image drums 103
Hewlett-Packard software license agreement
ATTENTION: USE OF THE SOFTWARE IS SUBJECT TO THE HP SOFTWARE LICENSE TERMS
SET FORTH BELOW. USING THE SOFTWARE INDICATES YOUR ACCEPTANCE OF THESE
LICENSE TERMS.
HP SOFTWARE LICENSE TERMS
The following License Terms govern your use of the accompanying Software unless you have a separate signed agreement with Hewlett-Packard.
License Grant . Hewlett-Packard grants you a license to use one copy of the Software. "Use" means storing, loading, installing, executing, or displaying the Software. You may not modify the Software or disable any licensing or control features of the Software. If the Software is licensed for "concurrent use," you may not allow more than the maximum number of authorized users to Use the Software concurrently.
Ownership . The Software is owned and copyrighted by Hewlett-Packard or its third-party suppliers.
Your license confers no title to, or ownership in, the Software and is not a sale of any rights in the
Software. Hewlett-Packard's third-party suppliers may protect their rights in the event of any violation of these License Terms.
Copies and Adaptations . You may only make copies or adaptations of the Software for archival purposes or when copying or adaptation is an essential step in the authorized Use of the Software. You must reproduce all copyright notices in the original Software on all copies or adaptations. You may not copy the Software onto any public network.
No Disassembly or Decryption . You may not disassemble or decompile the Software unless HP's prior written consent is obtained. In some jurisdictions, HP's consent may not be required for limited disassembly or decompilation. Upon request, you will provide HP with reasonably detailed information regarding any disassembly or decompilation. You may not decrypt the Software unless decryption is a necessary part of the operation of the Software.
Transfer . Your license will automatically terminate upon any transfer of the Software. Upon transfer, you must deliver the Software, including any copies and related documentation, to the transferee. The transferee must accept these License Terms as a condition to the transfer.
Termination . HP may terminate your license upon notice for failure to comply with any of these License
Terms. Upon termination, you must immediately destroy the Software, together with all copies, adaptations, and merged portions in any form.
Export Requirements . You may not export or re-export the Software or any copy or adaptation in violation of any applicable laws or regulations.
U.S. Government Restricted Rights . The Software and any accompanying documentation have been developed entirely at private expense. They are delivered and licensed as "commercial computer software" as defined in DFARS 252.227-7013 (Oct 1988), DFARS 252.211-7015 (May 1991), or
DFARS 252.227-7014 (Jun 1995), as a "commercial item" as defined in FAR 2.101(a) (Jun 1987), or as "Restricted computer software" as defined in FAR 52.227-19 (Jun 1987) (or any equivalent agency regulation or contract clause), whichever is applicable. You have only those rights provided for such
Software and any accompanying documentation by the applicable DFARs or FAR clause or the HP standard software agreement for the product involved.
104 Appendix B Service and support ENWW
HP Customer Care
Online services
For 24-hour access to information by using a modem or Internet connection
World Wide Web: Updated HP product software, product and support information, and printer drivers in several languages can be obtained from http://www.hp.com/go/support/ljP2010series (The site is in
English.)
Online troubleshooting tools
HP Instant Support Professional Edition (ISPE) is a suite of Web-based problem solving tools for desktop computing and printing products. ISPE helps you quickly identify, diagnose, and resolve computing and printing problems. The ISPE tools can be accessed from http://instantsupport.hp.com
.
Telephone support
Hewlett-Packard provides free telephone support during the warranty period. When you call, you will be connected to a responsive team that is waiting to help you. For the telephone number for your country/ region, see the flyer that came in the box with the product, or visit http://www.hp.com
then click Contact
HP . Before calling HP, have the following information ready: product name and serial number, date of purchase, and description of the problem.
You can also find support on the Internet at http://www.hp.com/go/support/ljP2010series . Click the support & drivers block.
Software utilities, drivers, and electronic information
Go to http://www.hp.com/go/support/ljP2010series . (The site is in English, but printer drivers can be downloaded in several languages.)
You can obtain additional information over the telephone. For telephone numbers, see the flyer that came in the box with the device.
HP direct ordering for accessories or supplies
Order supplies from the following Web sites:
North America: https://www.hp.com/post-embed/ordersupplies-na
Latin America: https://www.hp.com/post-embed/ordersupplies-la
Europe and Middle East: https://www.hp.com/post-embed/ordersupplies-emea
Asia Pacific countries/regions: https://www.hp.com/post-embed/ordersupplies-ap
Order accessories from http://www.hp.com
and click Supplies & Accessories . For more information, see
Supplies and accessories table on page 97 .
To order supplies or accessories over the telephone, call the following numbers:
United States: 1-800-538-8787
Canada: 1-800-387-3154
To find the telephone numbers for other countries/regions, see the flyer that came in the box with the device.
HP service information
ENWW HP Customer Care 105
To locate HP-Authorized Dealers in the United States or Canada, call 1-800-243-9816 (United States) or 1-800-387-3867 (Canada). Or, go to http://www.hp.com/go/cposupportguide .
For service for your HP product in other countries/regions, call the HP Customer Support telephone number for your country/region. See the flyer that came in the box with the device.
HP service agreements
Call: 1-800-HPINVENT [1-800-474-6836 (U.S.)] or 1-800-268-1221 (Canada).
Out-of-Warranty Service: 1-800-633-3600.
106 Appendix B Service and support ENWW
Availability of support and service
Around the world, HP provides a variety of service and support options for purchase. Availability of these programs will vary depending upon your location.
HP Care Pack™ Services and Service Agreements
HP has various service and support options that meet a wide range of needs. These options are not part of the standard warranty. Support services vary by location. For most products HP offers both inwarranty and post-warranty HP Care Pack Services and Service Agreements.
To identify service and support options for this device go to http://www.hpexpress-services.com/
10467a and type the device model number. In North America, Service Agreement information can be obtained through HP Customer Care. Call 1-800-HPINVENT 1-800-474-6836 (U.S.) or 1-800-268-1221
(Canada). In other countries/regions please contact your country/region specific HP Customer Care
Center. See the inbox flyer or go to http://www.hp.com
for the HP Customer Care telephone number in your country/region.
Extended Service: Call 1-800-HPINVENT 1-800-474-6836 (U.S.) or 1-800-268-1221 (Canada). Or, go to the HP Supportpack and Carepaq™ Services Web site at http://www.hpexpress-services.com/
10467a .
ENWW Availability of support and service 107
Guidelines for repacking the printer
Use the following guidelines when repacking the printer:
● If possible, include print samples and 5 to 10 sheets of paper or other media that did not print correctly.
● Remove and keep any cables, trays, and optional accessories installed in the printer.
● Remove and keep the print cartridge.
CAUTION: To prevent damage to the print cartridge, store the print cartridge in its original packing material, or store it so that it is not exposed to light.
● If possible, use the original shipping container and packing material. Shipping damage as a result of inadequate packing is your responsibility . If you have already disposed of the printer's packing material, contact a local mailing service for information on repacking the printer.
● Hewlett-Packard recommends that you insure the equipment for shipment.
108 Appendix B Service and support ENWW
C Printer specifications
This appendix provides information on the following topics:
●
●
●
●
ENWW 109
Physical specifications
Dimensions
Weight (3,000-page cartridge installed)
● Width: 350 mm (16.8 inches)
● Depth: 361 mm (14.2 inches)
● Height: 256 mm (10.0 inches)
HP LaserJet P2010 series: 10.7 kg (23.6 lb)
110 Appendix C Printer specifications ENWW
Electrical specifications
WARNING!
Power requirements are based on the country/region where the printer is sold. Do not convert operating voltages. Doing so might damage the printer and void the product warranty.
Table C-1 HP LaserJet P2010 Series printers
Power requirements (110)
Power requirements (230)
Power consumption
Rated current
110-127v (+/-10%), 50/60 Hz (+/-2)
220v-240v (+/-10%), 50/60 Hz (+/-2 Hz)
● During printing (24 ppm): 410 watts (average)
● During Ready (Standby)/Sleep*: 7 Watts
* Instant-on fuser technology
● Off: 0 watts
● 4.9 amps at 115 volts
● 2.9 amps at 230 volts
NOTE: Values are based on preliminary data. See www.hp.com
for current information.
NOTE: The power reported is the highest value measured for monochrome printing using all standard voltages.
NOTE: The recovery time from Ready/Sleep mode to the start of printing is less than
10 seconds because of the instant-on fusing.
NOTE: The heat dissipation in Ready mode is 25 BTU/hour.
ENWW Electrical specifications 111
Acoustic emissions
Declared per ISO 9296
Table C-2 HP LaserJet P2010 Series printers
Sound power level
Sound pressure level bystander position
Printing (23 ppm): L
WAd
= 6.24 Bels A and 62.4 dB (A)
Ready (Sleep): Inaudible
Printing (23 ppm): L pAm
= 50 dB (A)
Ready (Sleep): Inaudible
NOTE: Values are based on preliminary data. See http://www.hp.com/go/support/ ljP2010series for current information.
NOTE: Configuration tested: HP LaserJet P2014 base unit, 23 ppm, standard tray, A4 paper, and simplex continuous print.
Environmental specifications
Operating environment
Storage environment
Printer plugged into an AC outlet:
● Temperature: 10° C to 32.5° C (50° F to 90.5° F)
● Humidity: 20 to 80 percent (no condensation)
Printer unplugged from an AC outlet:
● Temperature: 0° C to 40° C (32° F to 104° F)
● Humidity: 10 to 80 percent (no condensation)
NOTE: Values are based on preliminary data. See www.hp.com
for current information.
112 Appendix C Printer specifications ENWW
D Regulatory information
ENWW 113
FCC compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase separation between equipment and receiver.
● Connect equipment to an outlet on a circuit different from that to which the receiver is located.
● Consult your dealer or an experienced radio/TV technician.
NOTE: Any changes or modifications to the printer that are not expressly approved by Hewlett-
Packard could void the user's authority to operate this equipment.
Use of a shielded interface cable is required to comply with the Class B limits of Part 15 of FCC rules.
114 Appendix D Regulatory information ENWW
Environmental product stewardship program
Protecting the environment
Hewlett-Packard Company is committed to providing quality products in an environmentally sound manner. This product has been designed with several attributes to minimize impacts on our environment.
Ozone production
This product generates no appreciable ozone gas (O
3
).
Power consumption
Power usage drops significantly while in Ready/Sleep mode, which saves natural resources and saves money without affecting the high performance of this product. To determine the ENERGY STAR® qualification status for this product see the Product Data Sheet or Specifications Sheet. Qualified products are also listed at: http://www.hp.com/hpinfo/globalcitizenship/environment/productdesign/ecolabels.html
Toner consumption
Economode uses significantly less toner, which might extend the life of the print cartridge.
Paper use
This product’s manual/optional automatic duplex feature (two-sided printing) and N-up printing (multiple pages printed on one page) capability can reduce paper usage and the resulting demands on natural resources.
Plastics
Plastic parts over 25 grams are marked according to international standards that enhance the ability to identify plastics for recycling purposes at the end of the product’s life.
HP LaserJet print supplies
It’s easy to return and recycle your empty HP LaserJet print cartridges—free of charge—with HP Planet
Partners. Multilingual program information and instructions are included in every new HP LaserJet print cartridge and supplies package. You help reduce the toll on the environment further when you return multiple cartridges together rather than separately.
HP is committed to providing inventive, high-quality products and services that are environmentally sound, from product design and manufacturing to distribution, customer use and recycling. When you participate in the HP Planet Partners program, we ensure your HP LaserJet print cartridges are recycled properly, processing them to recover plastics and metals for new products and diverting millions of tons of waste from landfills. Since this cartridge is being recycled and used in new materials, it will not be returned to you. Thank you for being environmentally responsible!
NOTE: Use the return label to return original HP LaserJet print cartridges only. Please do not use this label for HP inkjet cartridges, non-HP cartridges, refilled or remanufactured cartridges or warranty returns. For information about recycling your HP inkjet cartridges please go to http://www.hp.com/recycle .
ENWW Environmental product stewardship program 115
Return and recycling instructions
United States and Puerto Rico
The enclosed label in the HP LaserJet toner cartridge box is for the return and recycling of one or more
HP LaserJet print cartridges after use. Please follow the applicable instructions below.
Multiple returns (two to eight cartridges)
1.
Package each HP LaserJet print cartridge in its original box and bag.
2.
Tape up to eight single boxes together using strapping or packaging tape (up to 70 lbs).
3.
Use a single pre-paid shipping label.
OR
1.
Use your own suitable box, or request a free bulk collection box from the http://www.hp.com/ recycle or 1-800-340-2445 (holds up to eight HP LaserJet print cartridges).
2.
Use a single pre-paid shipping label.
Single returns
1.
Package the HP LaserJet print cartridge in its original bag and box.
2.
Place the shipping label on the front of the box.
Shipping
For all HP LaserJet print cartridge recycling returns, give the package to UPS during your next delivery or pickup, or take it to an authorized UPS drop-off center. For the location of your local UPS drop-off center, call 1-800-PICKUPS or visit http://www.ups.com
. If you are returning via USPS label, give the package to a U.S. Postal Service carrier or drop off at a U.S.Postal Service Office. For more information, or to order additional labels or boxes for bulk returns, visit http://www.hp.com/recycle or call
1-800-340-2445. Requested UPS pickup will be charged normal pickup rates. Information subject to change without notice.
Non-US returns
To participate in HP Planet Partners return and recycling program, just follow the simple directions in the recycling guide (found inside the packaging of your new printer supply item) or visit http://www.hp.com/recycle . Select your country/region for information on how to return your HP LaserJet printing supplies.
Paper
This product is capable of using recycled papers when the paper meets the guidelines outlined in the
HP LaserJet Printer Family Print Media Guide . This product is suitable for the use of recycled paper according to EN12281:2002.
Material restrictions
This HP product does not contain added mercury.
This HP product does not contain a battery.
116 Appendix D Regulatory information ENWW
Disposal of waste equipment by users in private households in the
European Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Material Safety Data Sheet (MSDS)
Material Safety Data Sheets (MSDS) for supplies containing chemical substances (for example, toner) can be obtained by contacting the HP Web site at www.hp.com/go/msds or www.hp.com/hpinfo/ globalcitizenship/environment .
For more information
To obtain information about these environmental topics:
● Product environmental profile sheet for this and many related HP products
● HP’s commitment to the environment
● HP’s environmental management system
● HP’s end-of-life product return and recycling program
● Material Safety Data Sheets
Visit www.hp.com/go/environment or www.hp.com/hpinfo/globalcitizenship/environment .
ENWW Environmental product stewardship program 117
Declaration of Conformity statements
Declaration of Conformity according to ISO/IEC 17050-1 and EN 17050-1
Manufacturer's Name:
Manufacturer's Address:
Hewlett-Packard Company
11311 Chinden Boulevard,
Boise, Idaho 83714-1021, USA declares that the product
Product Name:
Regulatory Model 3) :
HP LaserJet P2011/P2012/P2013/P2014 Series
BOISB-0602-00
Product Options:
Including: Q5931A — Optional 250–Sheet Input Tray
ALL
Toner Cartridges: Q7553A / Q7553X conforms to the following Product Specifications:
Safety: IEC 60950-1:2001 / EN 60950-1:2001 +A11
IEC 60825-1:1993 +A1 +A2/EN 60825-1:1994 +A1 +A2 (Class 1 Laser/LED Product)
GB4943-2001
EMC: CISPR22:1997 / EN55022:1998 Class B 1)
EN 61000-3-2:2000
EN 61000-3-3:1995 / A1
EN 55024:1998 +A1 +A2
FCC Title 47 CFR, Part 15 Class B 2) / ICES-003, Issue 4
GB9254-1998, GB17625.1-2003
Supplementary Information:
The product herewith complies with the requirements of the EMC Directive 2004/108/EC and the Low Voltage Directive 73/23/EEC, and carries the CE-Marking accordingly.
1) The product was tested in a typical configuration with Hewlett-Packard Personal Computer Systems.
2) This Device complies with Part 15 of the FCC Rules. Operation is subject to the following two Conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
3) For regulatory purposes, this product is assigned a Regulatory model number. This number should not be confused with the product name or the product number(s).
Boise, Idaho 83714, USA
July 2007
For Regulatory Topics ONLY, contact:
European Contact: Your Local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department HQ-TRE / Standards
Europe, Herrenberger Straße 140, D-71034 Böblingen, Germany, (FAX: +49-7031-14-3143)
USA Contact: Product Regulations Manager, Hewlett-Packard Company, PO Box 15, Mail Stop 160, Boise, Idaho 83707-0015, USA,
(Phone: 208-396-6000)
118 Appendix D Regulatory information ENWW
Regulatory statements
Laser safety statement
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration has implemented regulations for laser products manufactured since August 1, 1976. Compliance is mandatory for products marketed in the United States. The printer is certified as a "Class 1" laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968.
Since radiation emitted inside the printer is completely confined within protective housings and external covers, the laser beam cannot escape during any phase of normal user operation.
WARNING!
Using controls, making adjustments, or performing procedures other than those specified in this user guide could result in exposure to hazardous radiation.
Canadian DOC regulations
Complies with Canadian EMC Class B requirements.
« Conforme à la classe B des normes canadiennes de compatibilité électromagnétiques (CEM). »
Korean EMI statement
ENWW Regulatory statements 119
Laser statement for Finland
LASERTURVALLISUUS
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
HP LaserJet P2011-, HP LaserJet P2012-, HP LaserJet P2013- ja HP LaserJet P2014 -sarjan laserkirjoittimet ovat käyttäjän kannalta turvallisia luokan 1 laserlaitteita. Normaalissa käytössä kirjoittimen suojakotelointi estää lasersäteen pääsyn laitteen ulkopuolelle.
Laitteen turvallisuusluokka on määritetty standardin EN 60825-1 (1994) mukaisesti.
VAROITUS !
Laitteen käyttäminen muulla kuin käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING !
Om apparaten används på annat sätt än i bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.
HUOLTO
HP LaserJet P2011-, HP LaserJet P2012-, HP LaserJet P2013- ja HP LaserJet P2014 -sarjan kirjoittimien sisällä ei ole käyttäjän huollettavissa olevia kohteita. Laitteen saa avata ja huoltaa ainoastaan sen huoltamiseen koulutettu henkilö. Tällaiseksi huoltotoimenpiteeksi ei katsota väriainekasetin vaihtamista, paperiradan puhdistusta tai muita käyttäjän käsikirjassa lueteltuja, käyttäjän tehtäväksi tarkoitettuja ylläpitotoimia, jotka voidaan suorittaa ilman erikoistyökaluja.
VARO !
Mikäli kirjoittimen suojakotelo avataan, olet alttiina näkymättömälle lasersäteilylle laitteen ollessa toiminnassa. Älä katso säteeseen.
VARNING !
Om laserprinterns skyddshölje öppnas då apparaten är i funktion, utsättas användaren för osynlig laserstrålning. Betrakta ej strålen.
Tiedot laitteessa käytettävän laserdiodin säteilyominaisuuksista:
Aallonpituus 785-800 nm
Teho 5 mW
Luokan 3B laser
120 Appendix D Regulatory information ENWW
Index
Symbols/Numerics
10/100 networking and wireless
A accessories
B
button, print-cartridge-door 3
C
cartridges
cartridges, print
cleaning
control panel
ENWW
customer support
D
door
print cartridge 3 straight-through output 3
driver
Macintosh, problem
duplex (two-sided) printing
E
Embedded Web Server (EWS)
Configuration page 44 device status 44
Networking tab 44 order supplies 44
Settings tab 44 supplies status 44
Environmental Product
environmental specifications 112
errors
European Union, waste
EWS. See embedded Web server
F
features
G
graphics
H
I
information pages
Information tab (embedded Web
input tray
install
Index 121
J
L
life expectancy, print cartridge 99
loading media
optional tray 3 24 tray 1 24 tray 2 24
M
Macintosh
driver, accessing 16 driver, installing 16
maintenance
Material Safety Data Sheet
media
missing
multiple pages, printing on a single
N
network-setup problem-
Networking tab (embedded Web
O
operating systems, supported 12
order supplies and
ordering
output bin
manual two-sided
output path, straight-through 25
P
paper
paper input trays
phone numbers
ports, troubleshooting
power receptacle 3 power switch 3
print cartridge
HP policy on 99 life expectancy 99
storing 99 using HP cartridges 99
print cartridges
print media
print quality
improve 82 light or faded print 82
misformed characters 84 page skew 84
vertical repetitive defects 84 wave 84
printer
printer driver
printer information pages
printing
122 Index ENWW
multiple pages on a single sheet
on both sides of the paper
problem solving
printed page and
printer-computer
product
R recycling
HP printing supplies returns and
regulatory statements
Canadian DOC
declaration of conformity
environmental product
laser statement for
S
service
settings
Settings tab (embedded Web
software
software license
supported operating
solving
printed page differs from
vertical repetitive defects 84 wave 84
special media
special paper
specifications
straight-through output door 3
straight-through output path 25,
supplies
support
supported operating systems 12
T technical support
telephone numbers
text
toner cartridge. See print cartridge
tray 1
tray 2
troubleshooting. See problem solving two-sided printing
ENWW Index 123
U
USB port
W warranty
Web sites
Material Safety Data Sheet
Windows
driver, accessing 13 driver, installing 13
124 Index ENWW
© 2007 Hewlett-Packard Development Company, L.P.
www.hp.com
*CB450-90906*
*CB450-90906*
CB450-90906
Scarica
Link pubblico aggiornato
Il link pubblico alla tua chat è stato aggiornato. Puoi visualizzare e gestire i tuoi link di chat dopo la registrazione qui.
Link pubblico del documento
Pubblicità