Home Server TS mini
E5046
Package contents
1
Setting up your TS mini
3
1
Getting started
2
15G065278000
Quick Start Guide
Home network scenario
HOME SERVER TS mini
SPLENDID
MENU
SPLENDID MENU
Internet
Router
Internet
Remote Access
AC adapter Power cord TS mini
RJ45 LAN cable
Software Installation
CD
Recovery DVD
User Manual
Quick S tart Guide
Restore CD
HDD screws package
User manual Quick Start Guide
Warranty C ard
Warranty card
Notebook PCs
SPLENDID MENU
HDD
Desktop PCs
Multimedia Devices
HDD
2
3
E-SATA
1 1
1 2
Internet
1. Connect the supplied power cord to the supplied AC adapter. Then, plug the AC adapter to the DC IN jack on the TS mini rear panel and the power cord to an electrical outlet.
2. Connect one end of a network cable to the LAN port on the server rear panel, and the other end to your broadband router.
You must use a network cable to connect the TS mini to your broadband router. Wireless connection to your broadband router is not supported.
However, after you connect your server to your home network, home computers can connect to your server through wireless connection.
3. Press the power switch on the top panel to turn on the TS mini.
2
1
2
Installing the Software on Your First Computer
1
1 2
1
2
1
2 2
1
1
2
1
1. Double-click the Windows Home Server icon to bring up the logon window, and then enter the administrator password to log on to the Windows Home
Server Console.
2
2
1 1
2. On the Windows Home Server Console interface, you can start to remotely view, add, share, and protect important files on your home server. Turn over this
Quick Start Guide to see what you can do with the Windows Home Server Console.
1 2
1
2 1
Add ing a hard disk drive
1 1
HDD2 HDD1
1
2
2
2
1
2
3
2
2
1
2
1
1 1 1 1
2
2
1
1 1 1
1
1
4
2 1
1
2
2
5
1
2
2
2
1
HDD
2
1 1
1
1 1
1
SPLENDID MENU
2
1
1. Insert the Software Installation CD into the computer that is connected to your home network. The Windows Home Server Connector wizard starts.
If Autorun is NOT enabled in your computer, browse the contents of the Software Installation CD to locate the Install.exe file. Double-click the
Install.exe to run the Connector wizard.
2. Click Next, and then follow the onscreen instructions to finish the installation and the Windows Home Server Setup. You will be required to set the server name, administrator password, and several settings.
1
1. Install the new HDD to the home server.
1
2
1 the HDD1 bay.
(a) Power off the server and unplug the power cord.
2
2 thumbscrews to remove the left side case.
1
(c) Use a coin to loosen the three screws and put the screws at a visible place in case they are lost.
1
(d) Hold the plastic grip, and then lift up the HDD cage horizontally.
3
4
(e) Reverse and place the HDD cage on the stable surface.
(f) Fasten the bundled four screws to the new HDD, and then slide the
HDD into the empty HDD bay.
(g) Hold the plastic grip and align the two pins on the cage as shown to the mounting holes. Push down the HDD cage to the right side case.
(h) Fasten the three screws which were removed and put aside at the beginning.
5
(i) Slide the left side case back to the server body, and then fasten the two thumbscrews back to the case.
Server Console.
1
(a) Log on to the Windows Home Server Console.
1
(b) Click the Server Storage tab.
2
(c) Select the newly added hard drive (either internal or external) and then click Add to bring up the Add a Hard Drive Wizard. Click Next.
(d) Select from the following options:
• Add this hard drive to your server storage to increase the storage capacity of your home server.
• Use this hard drive to back up files that are stored on your home server.
1
(e) For detailed instructions, refer to the Windows Home Server Console
2
Help.
2 least or else the HOME SERVER cannot recognize the hard drive.
1
1
1
2
2
1
2
Setting up user accounts
Click the User Accounts tab to create user accounts for each user. User accounts are required in order to control access to the shared folders on Windows Home
Server.
Windows Home Server has a 10 user account limit, not including the built-in Administrator and Guest Account.
• Weak – select this policy if you want shorter passwords for user accounts.
The network security is weak, though.
• Medium (default) – passwords for user acounts must be at least five
characters long without complexity requirement.
• Strong – select this policy to mak access to your home network more
secure. Password complexity is required.
To create a user account
1. Log on to the Windows Home Server Console.
2. Click the User Accounts tab, and then the User Accounts Setup window appears.
3. Choose to use the Guest account; or, set up a password policy to configure the user accounts password complexity. Click OK.
A strong password is required if Remote Access is enabled.
Sharing files on your home server
In shared folders, you can organize and store files on Windows Home Sever to share them with other people on your home network.
To access shared folders on the home server
You may access the shared folders on your home server in several ways.
• from the Windows Home Server Console
• from the desktop shortcut
• from the Windows Home Server icon
• from the Windows Start Menu
• from My Network Places
• from the Internet
Then, you can copy files you want to share to the shared folders on the home server.
To modify the folder sharing access
1. Click the User Accounts tab on the Windows Home Server Console, and then double-click a user.
2. In the Properties for Guest dialog, click the Shared Folder Access tab.
3. Set the user’s access rights to existing shared folders on the home server.
• Full – the user can create, change, and delete any files in the shared
folder.
• Read – the user can only read the files in the shared folder.
• None – the user cannot read, create, change, and delete files in the shared folder.
3. Click OK.
Remotely accessing your home server over the Internet
Enabling remote access on the Windows Home Server Accessing the TS mini home page
To access your data and home computers from the internet whenever you are, you need to configure Windows Home Server to allow Remote Access.
1. Log on to the Windows Home Server Console.
2. Click Settings on the upper right corner of the Windows Home Server
Console window, and then click Remote Access in the left pane.
3. Under the Remote Access heading, click Turn on to enable the remote access configuration to your home server.
1. Open the Internet Explorer Web browser.
Ensure to use the Internet Explorer to access the home page. When you use other Web browsers, you may not use some features like Remote
Access to Computers or Connect to your Home Server.
2. Enter the Internet domain name assigned to you during the remote access setup procedures (For example, https://tsmini.homeserver.com). Then, the Logon web page appears.
3. Click the Log On button on the upper right corner.
4. Enter a personal user account and password.
You cannot use the Administrator account or the Guest account to log on to the home page. You must log on with a user account that is enabled for Remote Access.
5. Now you are on the TS mini home page. There are three tabs on the home page: Home, Computers, Shared Folders. Click each tab to go on.
To add, remove, disable, or modify a user account
• On the User Account tab, click Add and fill in the necessary information under the General tab.
• Select a user account, and then click Remove to delete it.
• Select a user account, and then click Properties to change the user account's password or disable the user account.
To disable the Guest account
1. On the User Account tab, right-click Guest, and then click Disable
Account.
2. A confirmation message appears. Click Yes.
For more detailed instructions, refer to the User Manual that came with the product package.
For more detailed instructions, refer to the User Manual that came with the product package.
Configuring a home-computer backup
You can customize the backup of each of your home computers from the Windows
Home Server Console.
To configure backups for a home computer
1. Log on to the Windows Home Server Console.
2. Click the Computer & Backup tab.
3. Right-click a computer and then click Configure Backup.
4. Follow the Backup Configuration Backup Wizard to select the volumes you want to back up and the folders you want to exclude from the backup.
To adjust the backup time
By default, the backup time starts from 12:00AM to 6:00AM. You can adjust the backup time from the Backup settings page.
To configure automatic backup management
You can configure how many monthly, weekly, and daily backups to keep for your home computers. To do this:
1. Log on to the Windows Home Server Console.
2. Click Settings and then Backup.
3. In Automatic Backup Management, specify the number of months, weeks, and days.
4. Click OK to complete the setting.
Restoring files from a backup
You can browse and restore lost files and folders from a backup.
To open files and folders from a backup
1. Log on to the Windows Home Server Console.
2. Click the Computers & Backup tab.
3. Select a home computer, and then click View Backups.
4. Select a backup, and then click Open.
5. Select a volume to open, and then click Open.
To restore lost files and folders from a backup
1. When you open the backup, browse and drag the files and folders that you want to a folder on your home computer.
2. Close the window when you are done copying the files and folders that you want to restore.
ASUS special features
ASUS TS mini provides three special features that enable you to conveniently control the system status, manage files and folders, and enjoy one-year-free large online space.
ASWM
ASWM (ASUS System Web-based Management software) is an interface that allows you to conveniently manage your home server status via Windows
Home Server Console.
Click the ASWM tab to control the system status.
ASUS Xtor Manager
ASUS Xtor Manager is an add-in tool that helps you easily and directly back up, synchronize, and manage files and folders on external USB/eSATA storage devices attached to the home server.
Click the ASUS Xtor Manager tab enter the main page.
ASUS WebStorage
ASUS WebStorage allows you to enjoy one-year-free online space and back up files to your home server. With Internet connection, you can access and share any files whenever you want and wherever you are.
Performing system recovery
Restoring Factory Defaults
Use the bundled ASUS HOME SERVER TS mini Recovery DVD to recover your home server, restore the home server to its factory default, or replace the main hard disk in your home server .
1. Repeat step 1-2 in the previous section “Recovering Window Home
Server”.
2. Select the option “ Return my server to the default factory state” and then click Next. Follow the onscreen instructions to finish the restore process.
If you perform Server Recovery, the server settings and all user accounts will be deleted; the data in shared folders still exist. If you perform Factory Reset, all data on the home server’s hard drives will be deleted.
Recovering Windows Home Server
1. Insert the ASUS HOME SERVER TS mini Recovery DVD into the computer that is connected to your home network. The Server Recovery wizard starts.
If Autorun is NOT enabled in your computer, browse the contents of the Recovery DVD to locate the Install.exe file. Double-click the
Install.exe to run the Recovery wizard.
2. Click Next and follow the onscreen instructions to find your home server.
3. Select the option “ Re-install Windows Home Server software” and then click Next. Follow the onscreen instructions to finish the recovery process.
Replacing the main hard drive in your home server
To install Windows Home Server on a new main hard drive
1. Follow the section “Removing a hard disk drive” under Server Storage to remove the existing main hard disk drive.
2. Follow the section “Adding a hard disk drive” under Server Storage to install a new main hard disk drive.
Always install the hard disk drive in which the OS is or will be installed to the HDD1 bay.
3. Repeat step 1-2 in the previous section “Recovering Window Home
Server”.
4. Select the option “Replace the main hard drive in my server”, and then click Next. Follow the onscreen instructions to complete the process.
