Introduction HDMI AUDIO DELAY Conversion Box

HDMI AUDIO DELAY
Conversion Box
TOP VIEW
Introduction
The ADD-01IW connects to the HDMI signal from your
source equipment (DVD player, satellite, cable… etc.) to
your HDMI receiver equipment.
With the simple interface of ADD-01IW, the audio delay
time can be adjusted so that sound and picture are
perfectly synchronized. Up to 2700ms (2.7 second) error
can be corrected. The HDMI audio signal is reproduced
bit-perfect so no loss of audio quality is incurred.
Also the ADD-01IW can convert the HDMI audio sound to
analog or digital.
Features
ƒ
ƒ
ƒ
ƒ
ƒ
Max Audio Delay time 2.7 seconds.
Audio delay adjustment scale is 10ms.
Supports 2-channel PCM analog audio.
Supports Coaxial digital audio
Supports compressed audio format signal.(only HMDI
and COAXIAL OUT)
c
d
e
f
Specifications
Input connector
g
1 x HDMI
1 x HDMI
2 x RCA(for Analog)
Output Connector
ADD-01IW
1 x RCA(for Coaxial)
Max Video support
WUXGA or 1080P@60Hz
Audio Input support
sample rate
Audio output support
sample rate
32K / 44.1K/ 48K
/ 96K / 192KHz
32K / 44.1K/ 48K
/ 96K / 192KHz
Power Adapter (Min.)
DC 12V with lock
ADD-01IW
Housing
Metal
Package Contents-
Weight
322g
Dimensions (LxWxH)
150x86x25mm
USER MANUAL
V1.0
ƒ
1 ADD-01IW Unit
ƒ
1 User manual
ƒ
1 Power adapter DC 12V
ƒ
2 Screws
ƒ
4 foot pads
ƒ
1 HDMI cable 1.2M
Any thing missed, please contact with your vendor.
-1-
1. Select HDMI to Analog OUT channel
2. Display current audio delay time
3. - : decrease time delay value
4. + : increase time delay value
5. CHG: change time unit to adjust the audio delay time.
(second/ 100ms / 10ms)
-2-
FRONT VIEW
1. Pressing button “CHG” to select time unit “second” to
change.
Operation
Setting the audio delay time
1. Select the time unit to adjust by pressing the button
“CHG”.
d
c
e
1. HDMI Input
2. RS232 port
3. Input Power Jack
2. Then the selected time unit LED will keep flash. The
user can change to the next time unit by pressing “CHG”.
“Second” LED flash.
2. Pressing button “-” once to decrease 1 to 0.
Second => 100ms => 10ms => Second…
Adjust “second”
REAR VIEW
3. Pressing button “CHG” to select time unit “100ms” to
change.
Adjust “100 ms”
c
d
e
4. Pressing button “+” three times to increase 2 to 5.
Adjust “10 ms”
1. Coaxial output port
2. Analog output port
3. HDMI output port
3. Pressing the “+” or “-“ to increase /decrease the value
Old delay value 1.20 sec
Time unit to change: 100ms
“+” increase value from 2 to 3
Installation
1. Connect input equipment source to ADD-01IW.
2. Connect ADD-01IW to output device. (e.g. speaker).
3. Connect the power cord and turn on the ADD-01IW.
4. Turn on the source device.
“-” decrease value from 2 to 1
5. Stop operation and wait several second the LED stop
flashing, then the new audio delay time will take effect.
6. “+” and “-“ can reset LED at the same time
Example:
Audio delay “1.20” second change to “0.50” second
5. Stop operation and wait the LED stop flashing, then the
new audio delay time “0.50” second take effect.
DIP Switch Settings
Select audio output channel from HDMI -input to “Analog” audio
output.
1,2
OFF,OFF
OFF,ON
ON ,OFF
ON ,ON
1-2 CH
3-4 CH
5-6 CH
7-8 CH
© C&C TECHNIC TAIWAN CO., LTD. All rights reserved.
Trademarks:
All the companies, brand names, and product names
referred to this manual are the trademarks or
registered trademarks belonging to their respective
companies.
Old audio delay time “1.20” second
-3-
-4-
-5-