advertisement
3G-SDI AUDIO
DELAY Conversion
Box
ADD-01HDW
U
SER
M
ANUAL
V1.0
ADD-01HDW
Package Contents-
1 ADD-01HDW Unit
1 User manual
1 Power adapter DC 12V
2
4 foot pads
Any thing missed, please contact with your vendor.
Introduction
The ADD-01HDW connects to the SDI signal from your source equipment to your SDI receiver.
With the simple interface of ADD-01HDW, the audio delay time can be adjusted so that sound and picture are perfectly synchronized. Up to 2700ms (2.7 second) error can be corrected. The digital audio signal is reproduced bit-perfect so no loss of audio quality is incurred.
Also the ADD-01HDW can convert the SDI audio sound to analog or digital.
Features
Max Audio Delay time 2.7 seconds.
Audio delay adjustment scale is 10ms.
Support high-resolution display up to 1080P@60Hz.
Supports 2-channel PCM analog audio.
Supports Coaxial digital audio(PCM only).
Specifications
TOP VIEW
e c d g
Input connector 1 x BNC f
1 x BNC for video
Output Connector
SDI Video support
Audio support sample rate
Power Adapter (Min.)
2 x BNC for audio
1 x RCA
[email protected], 625i@50,
720p@50/59.94/60,
1080i@50/59.94/60,
[email protected]/24/25/29.97/30,
1080p@50/59.94/60
48K
DC 12V with lock
Housing Metal
Weight 378g
Dimensions (LxWxH) 150x111x25mm
-1-
1. Select audio output channel to “Coaxial” and “Analog” audio output.
2. Display current audio delay time
3. - : decrease time delay value
4. + : increase time delay value
5. CHG: change time unit to adjust the audio delay time.
(second/ 100ms / 10ms)
-2-
FRONT VIEW
c d
1. SDI Input
2. SDI LOOP Output
3. RS232 port
4. Input Power Jack
REAR VIEW
e f
Operation
Setting the audio delay time
1. Select the time unit to adjust by pressing the button
“CHG”.
2. Then the selected time unit LED will keep flash. The user can change to the next time unit by pressing “CHG”.
Second => 100ms => 10ms => Second…
Adjust “second”
1. Pressing button “CHG” to select time unit “second” to change.
“Second” LED flash.
2. Pressing button “-” once to decrease 1 to 0.
3. Pressing button “CHG” to select time unit “100ms” to change. c d
2. Analog Audio Output e
Installation
1. Connect input equipment source to ADD-01HDW.
2. Connect ADD-01HDW to output device. (e.g. speaker).
3. Connect the power cord and turn on the ADD-01HDW.
4. Turn on the source device.
-3-
Adjust “100 ms”
4. Pressing button “+” three times to increase 2 to 5.
Adjust “10 ms”
3. Pressing the “+” or “-“ to increase /decrease the value
Old delay value 1.20 sec
Time unit to change: 100ms
“+” increase value from 2 to 3
“-” decrease value from 2 to 1
5. Stop operation and wait several second the LED stop flashing, then the new audio delay time will take effect.
6. “+” and “-“ can reset LED at the same time
Example:
Audio delay “1.20” second change to “0.50” second
Old audio delay time “1.20” second
-4-
5. Stop operation and wait the LED stop flashing, then the new audio delay time “0.50” second take effect.
DIP Switch Settings
Select audio output channel from 16-channel of SDI-input to
“Coaxial” and “Analog” audio output.
1 OFF GROUP 1-2,1-8CH ON GROUP 3-4,9-16CH
OFF,OFF Group1, 1-2 CH_Group3, 9-10 CH
OFF,ON Group1, 3-4 CH_Group3, 11-12 CH
2,3
ON ,OFF Group2, 5-6 CH_Group4, 13-14 CH
ON ,ON Group2, 7-8 CH_Group4, 15-16 CH
© C&C TECHNIC TAIWAN CO., LTD. All rights reserved.
Trademarks:
All the companies, brand names, and product names referred to this manual are the trademarks or registered trademarks belonging to their respective companies.
-5-
advertisement
Related manuals
advertisement