Brunswick Vector, Vector BL630D, Vector, Vector, Vector, Vector, Vector, Vector, Vector, Vector, Vector, Vector, Vector Service manual

Contents
Glossary of Terms..............................................................................................................................3
Vector Scorer Overview.....................................................................................................................5
Scorer Computer ............................................................................................................................6
Motherboard..................................................................................................................................10
Primary Patch Panel......................................................................................................................12
Secondary Patch Panel..................................................................................................................15
LCD Interface PCB.......................................................................................................................16
Video 3 PCB..................................................................................................................................17
Power Supply................................................................................................................................19
Hard Drive.....................................................................................................................................20
Backing up the Hard Drive Settings..............................................................................................21
Console Electronics..........................................................................................................................22
Keypads . ......................................................................................................................................22
Touchscreens (Flatscreens)...........................................................................................................24
LCD Console Control PCB...........................................................................................................25
Touchscreen Transformer..............................................................................................................27
Selecting Input Voltage for the Touchscreen Transformer......................................................28
LCD Touchscreen Adjustment Procedure.....................................................................................29
Basic Adjustments...................................................................................................................30
Image Position Adjustment.....................................................................................................31
LCD Touchscreen Cleaning..........................................................................................................32
Circuit Board and Component Removal..........................................................................................32
Motherboard Removal..................................................................................................................34
Motherboard Installation...............................................................................................................34
PCI Bus Board Removal.........................................................................................................40
PCI Bus Board Installation......................................................................................................40
Hard Drive Replacement..................................................................................................................41
Installation of Hard Drive.............................................................................................................41
Configure the Hard Drive..............................................................................................................42
Select overhead type (If set improperly in centers with keypads) and Bumpers
(Installations with Brunswick automated bumpers)................................................................42
Set Scorer Computer Configuration (All installations)...........................................................44
Updated the Drives Programing....................................................................................................46
Scorer Computer Synchronization................................................................................................46
Cabling Overview............................................................................................................................49
Cable Diagrams................................................................................................................................60
Vector Scorers 1
Intentionally Blank Page
2 Vector Scorers
Glossary of Terms
The following terms are used in this section. To better understand the information presented in the
section you should familiarize yourself with these terms.
100Base -TX - Twisted pair cabling used in an Ethernet network and in some installations provides
video for the LCD screens. This cable type connects the Scorer Computer(s) and Control desk
computer(s) to the Ethernet switch(es) allowing them to communicate. Some installations use this type
of cabling to connect the scorer computer to the LCD touchscreens and overhead monitors. This cable is
sometimes referred to a Cat5 cable because category 5 communication wiring is used to make the cable.
Also refer to Ethernet Switch.
BIOS (Basic Input/Output System) - A program stored in a EPROM (erasable programmable readonly memory) chip located on the Motherboard. This program controls how information is transferred
between the components and circuit boards inside a computer.
Distribution PCB - A circuit board located behind the pin camera on each lane pair that provides
power for the pin camera, controls machine on/off and reset, and handle signals needed for scoring
such as foul, sweep switch, and ball detector signals. It can also control AMF short cycle and bumpers
as needed. This PCB is not present in GS-Series Pinsetter installations.
Ethernet - A protocol that specifies how computers send information to one another.
Ethernet Switch - Device that is the central point of connection for the scorer computer(s) and
Control desk computer(s) in the Ethernet network. The Switch allows data to be sent/received at full
transmission speeds. Also refer to 100Base-TX.
Hard Drive - A computer’s primary storage device. The hard drive contains the programs and files that
make the computer function.
LCD Interface PCB - A circuit board in the Scorer Computer that adapts the scoresheet video so that it
can be displayed on the lower touchscreen displays.
Motherboard - A circuit board inside a Scorer Computer or Control Desk Computer that contains the
microprocessors and memory. The hard drives and most of the other PCBs in the computer connect to
this board. (Also referred to as the System Board).
PCI Bus - Peripheral Component Interface Bus - A design or protocol used in many computers that
defines how circuit boards connect to and use the resources provided by the motherboard. These are
the medium sized, white- colored slot connectors on the motherboard. The Video3 PCBs connect to the
motherboard through these slots.
Power Supply - An assembly located inside a computer that provides power to the components inside
the computer, the Vector camera assembly and the Vector keypads.
Primary Patch Panel - A pair of boards mounted to the bottom of the Scorer Computer that provides
connection points and surge protection for the overhead monitors, Keypad/Touchscreen, Distribution
PCB/GS Pinsetter and Brunswick automated bumpers. The primary patch panel has connections for 8
lanes.
RAM (Random Access Memory) - A short term storage area for information in a computer. Most
computers have this type of memory installed on small circuit boards called DIMMs.
Vector Scorers 3
RS-232 - The most popular type of serial communication used by computers. This type of
communication allows a computer to talk to a single specific device through a 9-pin connector called a
comport. Each device that the computer “talks” to will have its own dedicated comport.
RS-232 Converter - A small box used in the Vector system to translate between RS-232 and RS-485
communication. These boxes are needed for GS-Series Pinsetters and Brunswick automated bumpers.
RS-485 - A type of serial communication that allows a computer to talk to a multiple devices using one
“shared” comport. Also refer to Serial Communication.
Video3 PCB - A multifunctional circuit board located in a Scorer Computer. This board processes and
controls the video for the display monitors, processes the video received from the pin cameras, and
provides communication for the pinsetters (Distribution PCB) and communication and audio control for
the scoring consoles.
If LCD touchscreens are installed a second Video3 PCB is installed to process the video the lower
screens.
Scorer Computer - Computer(s) located at the curtain wall that control the scoring functions for a up to
8 lanes.
Secondary Patch Panel - An optional circuit board mounted on the right side wall of the Scorer
Computer that provides connections and surge protection for the lower LCD video. The Secondary
Patch Panel has connections for up to 8 monitor. This board is only installed when low LCD monitors
are used.
Serial Communication - A popular means of transmitting data between a computer and another
device. In the Vector system two types of serial communication are used; RS-232 and RS-485. Also
refer to RS-232 and RS-485.
4 Vector Scorers
Vector Scorer Overview
Two configurations are available in the Vector scoring system; Keypad or LCD Touchscreens
(Flatscreens). For the Keypad configuration two identical keypads are used for each lane pair. These
keypads are full-function keyboards that allow the bowler to enter all information needed to begin
bowling and change or correct information once bowling has begun. Entry options include names,
score correction, language selection, and other special features. A Scorer Computer mounted on the
curtain wall contains the electronics that control scoring and other functions. The scoring computer can
control the functions for up to 8 lanes. Refer to figure titled Vector Configurations
Vector Configurations
(1) Scorer computer
(2) left keypad or TOUCHSCREEN (3)right keypad or
(TABLE MOUNTED)TOUCHSCREEN (TABLE MOUNTED) (4) left keypad OR (5) right keypad or TOUCHSCREEN (6)cURTAIN WALL
TOUCHSCREEN (FLOOR MOUNTED)
(FLOOR MOUNTed)
Vector Scorers 5
Scorer Computer
The scorer computer(s) located at the curtain wall control scoring functions for up to 8 lanes. The
number and type of printed circuit boards (PCBs) housed inside the Scoring Computer depends on
whether the center has lower LCD Touchscreens or Keypads, the model of motherboard installed in the
scorer computer, and the version of the scorer computer. Scorer Computer includes a Motherboard, a Video3 PCB, and a pair of boards that make up the Primary
Patch Panel. When lower LCD touchscreens are installed, a Secondary Patch Panel, an LCD Interface
PCB and a second Video3 PCB are added to the computer to provide video for the lower screens. The
scorer computer is equipped with model BL630D motherboard that provides additional resources
including network (Ethernet) capability.
Additional components used in all configurations include a power supply and a hard disk drive. Refer
to the figures titled Scorer Computer for Widescreen Overheads (on following pages).
6 Vector Scorers
Scorer Computer For Widescreen Overheads
The function of the circuit boards, components and connections for the Scorer Computer include:
(1) Com 1 - This connection used to communicate to overhead monitors On/off and video input
selection for Brunswick’s LCD wide screens are controlled through this connection.
Vector Scorers 7
(2) Com 2 (Brunswick Automated Bumpers) - Output used to communicate to Brunswick’s
optional automated bumper system. The bumpers are “told” to raise or lower through this
connection.
(3) Console/Pinsetter Control - Connections for console Keypads or Touchscreens and
Distribution PCBs or GS Pinsetters for up to 8 lanes. The console connections provide
input from the keypads or touchscreens as well as power for keypads. The pinsetter control
connections provide communication and power for the Distribution PCBs or communication for
GS pinsetters. Refer to (17) Primary Patch Panel.
(4) Console Video (Lower Touchscreens) - RJ-45 video output connections to the lower
flatscreens for up to 8 lanes. Refer to (9) Secondary Patch Panel (Optional).
(5) Network Connection - The connection point for the 100Base-TX (Cat5) cable from the
Ethernet Switch.
(6) Ethernet Filter PCB - A circuit board that provides filtering for the Ethernet signal.
(7) Hard Drive - The hard drive contains windows operating system and the Vector programming
for the Scorer Computer.
(8) LCD Interface PCB (Touchscreen installations only) - A circuit board that adapts the
scoresheet video so that it can be displayed on the lower flatscreen displays.
(9) Secondary Patch Panel (Optional) - An optional circuit board mounted on the inside side
wall of the Scorer Computer that provides connections and surge protection for the lower LCD
video. The Secondary Patch Panel has either RJ-45 connectors to handle up to 8 lanes Refer to
(4) Console Video (Touchscreen only).
(10) Main Power Input - 120VAC or 240VAC main input power for the Power Supply. Refer to (20)
Voltage Selector and (15) Power Supply.
(11) Main Power Switch - Power switch for the Scorer Computer. Pressing this button turns the
Scorer Computer On/Off .
(12) Motherboard - (Also referred to as the System Board). This circuit board provides memory
and processing capability for the scorer computer, interfaces the hard drive, sound circuits for
the exciter audio and Ethernet capability. The Video3 PCBs plug into this board.
(13) Overhead Video Output- Connections for the video to the overhead monitors. These
connections provide video for up to 8 overhead monitors. The connectors are RJ-45 type for
Widescreen Overhead Monitors. Refer to (17) Primary Patch Panel.
(14) Pin Camera Video Inputs - Connections for the video signal coming from the pin cameras for
up to four lane pairs. These connections are not used when on lanes with GS-Series Pinsetters.
(15) Power Supply - This assembly provides power to the components inside the Scorer Computer,
Distribution PCBs and Vector Keypads. Input to the power supply can be 120 VAC or 240 VAC.
Its output is 5 VDC and +/- 12 VDC.
8 Vector Scorers
(16) Power Supply Switch - Switch for the Power Supply unit. Turning this switch off disables the
power supply and removes power from the motherboard.
(17) Primary Patch Panel PCBs - A pair of circuits board mounted to the bottom of the Scorer
Computer that provides connections and surge protection for the overhead monitor’s video and
the communication signals for the Keypad/Touchscreen and Distribution PCB/GS Pinsetter.
The panel consists of a processor board and a connection board. The connection board has RJ45 type connectors that connect to the widescreen overhead monitors. The primary patch panel
has connections for 8 lanes. Refer to (13) Overhead Video and (3) Console/Pinsetter Control.
(18) Scorer Computer - Computer(s) located at the curtain wall that control the scoring functions
for a up to 8 lanes.
(19) Video3 PCBs - This board processes and controls the video for the overhead monitors,
processes the video received from the pin cameras, and provides communication for the
pinsetters (Distribution PCB) and communication/audio control for the keypads/touchscreens. If
touchscreens are installed a second Video3 PCB is used to provide video for the lower screens.
(20) Voltage Selector - Selector switch on some power supplies that allows the user to configure the
supply for an input voltage of 120 VAC or 240 VAC. The newest power supply does not require
configuration.
Vector Scorers 9
Motherboard
The Vector Scorer Computer uses high performance industrial motherboards as its main PCB. Since
January 2012 the ITOX model BL630D equipped with an Intel 2.4GHZ or later processor along with at
least 512MB of RAM has been used in the scorer computer.
The motherboard is responsible for processing information, making calculations and supplying power
and memory for the boards plugged into its PCI Bus. The board also has integrated circuits that allow it
to interface to the Scorer Computer hard drive, process the exciter audio used when the exciter graphics
are displayed, and monitor the system’s temperature, voltage, and cooling fans.
The onboard video capability is used to configure the motherboard and troubleshoot the scorer
computer. Model BL630D also include onboard Ethernet. Refer to the figure titled Vector Motherboard
- ITOX BL630D.
Vector Motherboard - ITOX BL630D
The function of the main components on the Motherboard Model BL630D are:
(1) Audio Out Connector - Connector to the Primary Patch Panel for the exciter audio. The audio
is then routed to the scorer consoles as needed.
(2) Battery - Provides battery backup for setup information stored in CMOS memory so that it is
retained in case of a power outage.
10 Vector Scorers
(3) Com 1 Connector - This connector is used to communicate to the optional CRT TV-Only
Monitors or to Brunswick provided widescreen overhead monitors.
(4) Com 2 Connector - This connector is used to communicate to optional Brunswick automated
bumpers.
(5) DIMM Sockets (Dual Inline Memory Module) - Connectors where the RAM is installed.
(6) Hard Drive Connector - Connection for the Scorer computer’s hard drive. When a SATA
(serial interface) hard drive is used, connect the data cable from the SATA drive to the
connection labeled SATA 0. If a PATA (parallel interface) hard drive is used, connect the blue
“System” connector of the data cable attached to the PATA drive to the connection labeled IDE.
(7) Keyboard Connector - Connection for a standard computer keyboard that can used when
configuring the motherboard BIOS or to maintain the Scorer Computer.
(8) Microprocessor - The chip responsible for processing of information for the Scorer Computer.
(9) PCI Slots (Peripheral Component Interconnect Slots) - This term refers to a group of
white connectors located on the motherboard where the other circuit boards plug into. These
connectors provide the boards with access to data and memory, the microprocessor, and to
each other. The boards also receive power through the connector. For motherboard BL630D, the
Video3 pcb(s) plug into these connectors.
(10) PCI Express Slots - Not Used
(11) Power Connector - Connector for the +5VDC, +12VDC, and -12VDC coming from the power
supply.
(12) Power Switch - Connection for the push button power switch located on the left side of the
Scorer Computer.
(13) Video Connectors - Connection for a standard computer monitor that can be used to set up
the motherboard BIOS and to troubleshoot scorer computer problems. Normally the VGA
connection is used to connect the monitor but the DVI can be used as an alternative .
(14) Ethernet Connection - The 100Base-TX cable from the Network Connector located on
the right side of the Scorer Computer attaches to the motherboard at this connector allowing
the Scorer Computer to communicate with the control desk system. Although the BL630
motherboard provides two network circuits always use the one closest to the video connectors
(LAN 1). Do not use the one closest to the audio connectors (LAN 2).
(15) +12 CPU Power - 12V input form the power supply that provides additional current for the
processor.
Vector Scorers 11
Primary Patch Panel
The Primary Patch consists of two circuit boards. The processor board contains circuits for noise
suppression, controlling to which console the exciter audio will be sent, and adapting the video so that it
can be sent over Cat5 (Ethernet) cabling. The primary patch panel has connections for 8 lanes. Refer to
figures titled Primary Patch Panel, Primary Patch Panel - Processor Board and Primary Patch Panel
- Connector Board .
Primary Patch Panel
(1) processor board PCB
(2) connector PCB
Primary Patch Panel - Processor Board
12 Vector Scorers
The functions of the connectors on the Primary Patch Panel Processor board used in Scorer Computer
are:
(1) Audio In (J1) - Connection for the exciter audio coming from the motherboard. The board
applies the audio signal to one of eight lines leaving the board at J6. Which lane gets the audio
is determined by the Video3 PCB.
(2) Audio Out (J2) - Not used.
(3) Exciter Audio / Video Select Out (J6) - Output for the exciter audio signal that entered the
board at J1 and the video select signals that entered the board at J5. These signals route to the
connector PCB. The audio is sent to the keypad/touchscreen. The video select signal is used to
switch the CRT overheads between scoresheet an TV. See (1) Audio In (J1) and (12) Video/Audio
Select In (J5)
(4) COM 1 In (J11) - Input for the COM1 signal originating at the motherboard. This signal is
routed through the processor board along with the other communication signals to J7. Com 1 is
used to control the Widescreen overhead monitors. See (6) Comm Out (J7).
(5) COM 2 In (J10) - Input for the COM 2 signal originating at the motherboard. This signal is
routed through the processor board along with the other communication signals to J7. Com 2 is
used to control Brunswick automatic bumper systems. See (6) Comm Out (J7).
(6) Comm Out (J7) - Output connection for the communication signals that entered the board at
the Com1 (J11), Com2 (J10), Keyboard (J9) and Pinsetter (J8) connections. These signals are
cabled to J22 of the patch panel connector board. See (4) Com 1 In (J11), (5) Com 2 In (J10), (10)
Pinsetter Comm In (J8), (7) Keyboard Comm In (J9).
(7) Keyboard Comm In (J9) - Input for the communication signals originating at the Video3 that
used to “talk” to the console keyboards (or touchscreens). The signals are routed through the
processor board along with the other communication signals to J7. See (6) Comm Out (J7).
(8) Pin Camera Video In (J13) - Not used.
(9) Pin Camera Video Out (J12) - Not used.
(10) Pinsetter Comm In (J8) - Connection for the communication signals originating at the Video3
that are used to “talk” to the distribution PCB or GS pinsetters. The signals are routed through
the processor board along with the other communication signals to J7. See (6) Comm Out (J7).
(11) Power In (J3) - +12VDC power input for the board. Although the power supply unit provides
both +12VDC and +5VDC, only the +12VDC is used.
(12) Video/Audio Select In (J5) - Connection for the video signals, exciter audio selection signals,
and CRT Video selection signals originating at the Video3 PCB. The video signals are routed
to the Video Out connection (J4). The exciter audio selection signals are used by the board
to determine which lane gets the exciter sound. The CRT video selection signals are routed
through the board to J6. Refer to (11) Video Out (J4) and (3) Exciter Audio/Video Select Out
(J6).
(13) Video Out (J4) - Connections for the scoresheet video and the TV/Scoresheet select signal for
the upper monitors. The signals are routed to J1 of the patch panel connector board. See (10)
Video/Audio Select In (J5).
Vector Scorers 13
Primary Patch Panel - Connector Board
The functions of the connectors on the Primary Patch Panel Connector board used in Scorer Computer
are:
(1) Camera Video In (J21) - Not Used
(2) COM 1 Out (J2) - This signal is used to control widescreen overhead monitors.
(3) COM 2 Out (J12) - Output used to communicate to the optional Brunswick automated bumper
system. The bumpers are “told” to raise or lower through this connection.
(4) Comm In (J22) - Connection for the communication signals coming from J7 of the Primary
Patch Panel Processor board. The communication signals are routed to the DIST connectors
(J13, J15, J17, J19), Keyboard connectors (J14, J16, J18, J20), Com2 (J2) and Com2 (J12) as
appropriate.
(5) DIST Connectors (J13, J15, J17,J19) - Connection for communication and power to the
Distribution PCB located in the camera assembly. When GS pinsetters are installed these
connections are used to communication with the GS Pinsetter electronics.
(6) Exciter Audio / Video Select In (J23) - Connection for the exciter audio and video select
signals coming from J6 of the processor board. The sound is routed to the keyboard connectors
J14, J16, J18, and J20. The video select is only used on the CRT connector board and is routed
to the overhead video connectors J3 - J10.
(7) Keyboard Connectors (J14, J16, J18, J20) - Connections used to communicate to the Keypad/
Touchcreen and provide exciter audio to the lower Keypads or Touchscreens. Power for keypads
are also supplied through this connection.
14 Vector Scorers
(8) Overhead Video Connectors (J3-J10) - These RJ-45 connections provide scoresheet video for
up to 8 overhead monitors.
(9) Power In (J11) - Power input for the Board. The power supply unit provides +12VDC and
+5VDC to the board through this connection.
(10)Video Board (J1) - Input connection used to receive the video signals from a Video3 PCB.
These signals are then routed to the Overhead output connectors. Refer to (8) Overhead Video
Connectors (J3-J10)
Secondary Patch Panel
The Secondary Patch panel provides connections and surge protection for the lower LCD touchscreen’s
video. The secondary patch panel has connections for 8 lanes. This board is also referred to as the
LCD Patch Panel. Refer to figure titled Secondary Patch Panel.
Secondary Patch Panel
The function of the connectors on the secondary patch panel are:
(1) Console Video Output (J1-J8) - Connection for the scoresheet video signal to the lower LCD
screens.
(2) Power In (J9) - Power input for the Secondary Patch panel. Although the power supply unit
provides and input of +12VDC and +5VDC, the board only uses the connector to provide a
ground signals for the protection circuits.
(3) Video In (J10) - Input connection for the console video signals coming from J3 of the LCD
Interface PCB. These signals are then routed to the console output connectors. Refer to (1)
Console Video Output (J1 - J8) Vector Scorers 15
LCD Interface PCB
The LCD Interface PCB is used to adapt the video for the lower screens so that it can be displayed
properly on the LCD flatscreens. The board receives 8 lanes of RGBS video from a Video3 PCB and
converts the video intended for the lower LCD Screens. The signals for all eight lanes are converted
and transferred to the Secondary Patch Panel through connector J3. Refer to figure titled LCD Interface
PCB.
LCD Interface PCB
The functions of the connectors on the LCD Interface PCB are:
(1) Power In (J1) - Connection for the incoming +12DC coming from the power supply unit.
(2) Video Inputs (J4) - Input connection for 8 lanes of scorer video received from the Video3 PCB.
(3) Video Out (J3) - Video output for 8 lanes of converted video for the Secondary Patch Panel.
This connection is only present when the board is used in an 8 lane scorer computer.
16 Vector Scorers
Video 3 PCB
The Video3 PCB is a multifunction board. It provides video for the overhead monitors, video control
for CRT overheads, processes the video received from the pin cameras, provides communication to the
Distribution PCBs or GS pinsetters as needed, and provides communication and exciter audio control
for the scoring consoles. If flatscreens are installed a second Video3 PCB used to process the video the
lower screens. Refer to figure titled Video3 PCB.
Video3 PCB
The function of the connector and components on the Video3 PCB are:
(1) Board Configuration Jumpers (JP1, JP2, JP3, JP4) - These jumpers are used to set the board
ID and configuration. JP1 and JP2 are used to set the board ID while JP3 and JP 4 are used to
set the communication protocol. Set the jumpers as follows:
Board
SETTINGS
JP1
JP2
JP3
JP4
Video3 PCB for Primary Patch Panel
Remove
Remove
Remove
Remove
Video3 PCB for Secondary Patch
Panel
Remove
Install
Remove
Remove
(2) Camera Connector - Connections for the pin cameras. This connection is not used for the
Video3 PCB that is connected to the secondary patch panel. See (7) Pin Camera Input (1-4).
(3) Digital Out - Not Used. (4) Distribution / GS - Connection that provides RS-232 communication signals for the
Distribution board (or GS Pinsetter) This connection is not used for the Video3 PCB that is
connected to the secondary patch panel.
Vector Scorers 17
(5) PCI Connector - Connection to the motherboard.
(6) Keyboard Connector - Connection that provides RS-232 communication signals for the
keypad (or touchscreen). This connection is not used for the Video3 PCB that is connected to the
secondary patch panel.
(7) Pin Camera Input ( 1-4) - Not Used. An alternative method for connecting the pin cameras to
the board. See (2) Camera Connector.
(8) Video Connector - This connection provides the overhead video and exciter audio select
signals to the Primary Patch Panel board(s) or lower screen video to the LCD Interface PCB
(Video3 PCB #2).
(9) Pin Camera Contrast Adjustment - This adjustment controls the contrast level of the video
image received from the pin cameras. If the pin image displayed on the pin setting page at the
control desk is too bright or too dim, adjust this control as needed to provide a usable image.
18 Vector Scorers
Power Supply
The power supply in the Scorer Computer is a professional grade ATX power supply that provides DC
voltage to all circuit boards inside the Scorer Computer motherboard, Primary Patch Panel, Secondary
Patch Panel, LCD Interface PCB, Video3 PCBs, and hard drive. It also provides power to the Vector
keypads and pin camera assemblies if installed. Input to the power supply can be 120 VAC or 240 VAC.
The power supply do not have the voltage selection switch as they automatically configure themselves
based on the supplied input voltage. The output is +5 VDC and +/-12 VDC. Refer to the figure titled
Power Supply.
Power Supply
Functions of the components and connectors on the power supply are:
(1) Motherboard Connector - The large 20 +4 connector (7) provides the DC voltage need to
run the motherboard and the boards plugged into the PCI Bus. The 4-pin power connectors (8)
provides the processor with additional 12DC power. Motherboard model BL630 requires 2 of
these connectors or 1, 8-pin connector (not shown).
(2) Power Connectors - Connectors used to supply DC voltage to the SATA hard drive (6) or
PATA hard drive (5) and Primary Patch Panel, Secondary Patch Panel, Video3 PCBs, and the
LCD Interface PCB (5) as needed.
NOTE: The power connections are used, as needed, based on what PCBs are located in the
scoring computer.
(3) Power Receptacle - Connector for main power into the supply. Remove the cable attached to
this receptacle before working inside the scoring computer.
IMPORTANT!: Before turning the Power Switch to the off position always power down the
scorer computer using the main power switch located at the bottom of the side panel.
Vector Scorers 19
Hard Drive
CAUTION! Damage to the hard drive can result if it is subjected to excessive
vibration, jarring, or rough handling. Handle with care.
The hard drive located in the Scorer Computer contains a Windows operating system and Brunswick
programming to allow scoring for up to 8 lanes. The Brunswick program allows the Scorer
Computer to control keypads/ touchscreens and pinsetters, generate video for Overhead monitors and
communicate to the desk computer(s). Without the hard disk, the Scorer Computer will not operate
and the consoles will not start up. In addition to the programming, the hard drive stores current
game information, and contains files that store lane number information to identify what lanes the
computer controls, the configuration and calibration settings for the lanes, commercials that can be
displayed when the lanes are off, and the exciter graphics and animations that are used during bowling.
This information must be updated and configured anytime the hard disk is replaced. For additional
information on hard drive replacement refer to the hard drive replacement instructions located at the
end of this section. The hard drive is a solid state SATA (Serial interface). Refer to the figure titled
Scorer Computer Hard Drive.
(3)
POWER
CONNECTOR
OL
NS
O
CO
DE
VI
E
OL
NS
O
CO
DE
VI
E
E
OL
NS
O
CO
DE
VI
E
OL
NS
O
CO
DE
VI
OL
NS
O
CO
DE
VI
E
OL
NS
O
CO
DE
VI
E
E
OL
NS
O
CO
DE
VI
E
OL
NS
O
CO
DE
VI
(2)
SATA HARD
DRIVE
(1)
DATA
CONNECTOR
8
7
6
5
4
3
2
1
ETWORK
CAMERA 1
CAMERA 2
CAMERA 3
CAMERA 4
Scorer Computer Hard Drive
The function of the components on the hard drive are:
(1) Data Connector - Connection used to transfer information between the hard drive and the
Motherboard. The cable from this connection attaches to J15 of Motherboard.
(2) SATA Hard Drive (Serial Interface) - A solid state device that contains the program for the
Scorer Computer.
(3) Power Connector - Connection for the DC power cable from the Power Supply.
20 Vector Scorers
Backing up the Hard Drive Settings
Having a good back-up of the settings of the Scorer Computer’s hard drives allows the mechanic to
easily restore a drives configuration and quickly get a replacement drive up and running. To back up a
Scorer Computer’s hard drive configuration perform the following steps.
1. At the Windows desktop screen (the screen with the icons) of the Vector or Vector Plus
SERVER computer, double-click on the “My Computer” icon.
2. Double-click on the ‘C’ drive.
3. Double-click on the “Brunswick” folder , then double-click the “Utilities” folder.
4. Double-click on the Config.exe file to run the file. Refer to the figure titled Config.exe screen.
Config.exe Screen
5. Select the Score Computer button.
6. At the message, “Is CMSERVER a scoring computer?”or “Is DATOR a scoring computer?”,
click No.
7. Select the desired Scoring Computer from the drop-down list on the top-left of the window.
To backup a configuration, click “Backup Configuration”. To restore a previously backed
up configuration, click “Restore Configuration.” Refer to the figure titled Scorer Computer
Configuration Screen.
Scorer Computer Configuration Screen
Vector Scorers 21
Console Electronics
Keypads
To allow for simultaneous entry by the bowlers, keypads are used for each lane. These keypads are
identical in every way and contain circuit boards that are interchangeable. The Keypad Interface PCB
located in the keypad housing handles the bowler input, sound selection and communication for the
console. Refer to the figures titled Bowler Keypad and Keypad Interface PCB.
Bowler Keypad and Interface PCB
(1)Keyboard
(2) keypad Interface PRINTED CIRCUIT BOARD
(4) SPEAKER
22 Vector Scorers
(3)MICROPHONE
Keypad Interface PCB
The function of the connectors and components on the Keypad Interface are:
(1) Diagnostic LED (D3) - This light flashes to indicate that the PCB is functioning.
(2) Global Audio In (J5) - Input of the intercom audio(s) and TV/DVD audio (global audio)
originating at the control desk audio control box. If the board is located in the first console,
the cable comes from the control desk Audio Control box. For the reset of the lanes, the cable
comes from the Keypad Interface PCB for the previous lane. Refer to (3) Global Audio Out
(J6).
(3) Global Audio Out (J6) - Output of the global audio for the next console. This connection
allows the continuation of the intercom and TV audios to the next lane. If the board is installed
in the last console and the signals do not continue, they are terminated using the termination
jumper JP4. Refer to (4) Global Audio Terminator (JP4).
(4) Global Audio Terminator (JP4) - Jumper used to terminate the global audio signal. If the
global audio cable does not continue to another console from J6, terminate the signal by placing
a jumper between pins 2 and 3 (T). Otherwise place a jumper between pins 1 and 2 (U).
(5) Keyboard (J1) - Connection to the keyboard in the console.
Vector Scorers 23
(6) Comm/Power/Exciter Audio In (J3) - Connection for the power, communication and audio
exciter signals. When the board is located in left console (odd lane), signals for both the left
and right lane coming from the Primary Patch Panel of the Scorer Computer enter the board at
J3. If the board is located as the second keypad of the lane pair (even lane), the signals route
through the odd lane keypad then to this connector. Refer to (7) Comm/Power/Exciter Audio
Out (J4).
(7) Comm/Power/Exciter Audio Out (J4) - Connection for the communication, power and audio
exciter going to the second keypad for the lane pair. This connection is only used on the left
(odd) lane keypad.
(8) Microphone (J7) - Connection to the microphone used for the intercom system.
(9) Speaker (J2) - Connection to the speaker. The circuit board applies the selected audio to the
speaker through this connection. This audio includes the VCR (TV) audio, intercom, exciter
audio, and keyboard beep.
Touchscreens (Flatscreens)
The LCD flatscreens provide the bowler with lower scoresheet video and the ability to in input
information through a touchscreen. Screens are installed at each lane for the convenience of the
bowler. The screens are identical in every way and interchangeable. The only individually replaceable
board is the LCD Console Control PCB located in the back of the display housing. This board handles
the bowler input, sound selection and communication for the console. Refer to the figure titled LCD
Flatscreens.
LCD Flatscreens
(1) lcd console control pCB (2) microphone (4) touchscreen
24 Vector Scorers
(3)speaker
LCD Console Control PCB
The LCD Console Controller PCB interfaces the flatscreen’s touchscreen to the Scorer Computer and
the global audio signals to the console.
Jumpers on the board need to be set in order to configure the board for use with the Vector system and
to properly terminate the Global Audio Signals Refer to the figure titled LCD Console Control PCB.
LCD Console Control PCB
The function of the components and connectors on the LCD Console Control PCB are:
(1) Audio In (J1) - Input of the intercom audio(s) and TV/DVD audio (global audio) originating at
the control desk audio control box. If the board is located in the first console, the cable comes
from the control desk Audio Control box. For the reset of the lanes, the cable comes from the
Keypad Interface PCB for the previous lane. Refer to Audio Out (J2),
(2) Audio Out (J2) - Output of the global audio to the next console. This connection allows the
continuation of the intercom and TV audios to the next lane. If the board is installed in the last
console and the signals do not continue, terminate the signal using the termination jumper JP8.
(3) Audio Terminator (JP8) - Jumper used to terminate the global audio signal. If the global
audio cable does not continue to another console from J2, terminate the signal by placing a
jumper between pins 2 and 3 (T). Otherwise place a jumper between pins 1 and 2 (U).
(4) Board Select (JP7) - Jumper used to select whether the console is for the left lane or the right
lane when the board is used for the Frameworx scoring system. In the Vector system, the
cabling from the Scorer Computer automatically determines left/right designation. For the
Vector System always set the jumper on pins 1 and 2 (L).
(5) Communication Input (J9) - Connection for the communication (RS-232) originated at the
Primary Patch Panel in the Scorer Computer. If the board is located on the right (even) lane,
the communication signal is routed through the left (odd) lane board. Refer to (15) Even Lane
Communication Out (J10).
Vector Scorers 25
(6) Even Lane Exciter Audio Out (J5) - Connection for the audio exciter going to the even lane
touchscreen of the lane pair. Refer to (14) Exciter Audio In (J4).
(7) LLAN Terminator (JP1) - Jumper used to terminate the communication signal when the board
is used with the Frameworx scoring system. For the Vector scoring system always place the
jumper between pins 1 and 2 (U).
(8) Microphone (J6) - Connection to the microphone used by the intercom system
(9) Power (J7) - 25VAC input power for the circuit board enters here. The power originates at the
touchscreen transformer located on the curtain wall near the Scorer Computer.
(10) RS232/RS485 Select (JP9) - Jumper used to select whether the PCB will use J9 or J4 for the
communication input. Because the Vector scoring system uses J9 as the communication input
always set the jumper to RS-232.
(11) Screen Adjustments - Push-buttons that allow the user to access an on-screen adjustment menu
to adjust brightness, contrast, color, image position, and screen brightness (for screens equipped
with adjustable backlights).
Reset (SW1) - Use this button to reset all options to factory default settings. Up (SW2) - Use this button to increase the setting of the selected option or to move up the
selection menu.
Down (SW3) - Use this button to decrease the setting of the selected option or to move
down the selection menu.
Select (SW4) - Use this button to select an option from the menu or to enter the setting for
an option.
(12) Speaker (J3) - Connection to the speaker. The circuit board applies the selected audio to the
speaker through this connection. This audio includes the VCR audio, intercom, exciter audio,
and keyboard beep.
(13) Screen Power/Comm (J8) - Connection to the touchscreen circuitry. Power and the push
button switch signals are send out this connection.
X/Y coordinates for the touchscreen is received through the connection
(14) Exciter Audio In (J4) - Input for the exciter audio originating at the scorer computer. If the
board is located on the right (even) lane, the exciter audio signal is first routed through the left
(odd) lane board. Refer to (6) Exciter Audio Output (J5).
(15) Even Lane Communication Out (J10) - Connection for the communication (RS-232) going to
the touchscreen for the even lane of the lane pair. Refer to (5) Communication Input (J9).
(16) RS232/485 Select Jumper (JP10) - Jumper used to configure the PCB for RS232 or RS485
operation. For the Vector scoring system set this jumper to the RS232 position.
(17) Heartbeat LED (D12) - Flashes when the PCB is functioning normally.
26 Vector Scorers
Touchscreen Transformer
The touchscreen transformer supplies 18 VAC - 25VAC power to the LCD flatscreens. Circuit breakers
on the unit protect the screens from power surges. The transformer assembly accepts either 110-120
VAC or 220-240 VAC. Selection of the desired input voltage is done at the input receptacle. Refer to
the figure titled Touchscreen Transformer.
Touchscreen Transformer
The function of the connectors and components on the touchscreen transformer are:
(1) Power Out - 18VAC - 25VAC power out.
(2) Circuit Breakers - Manually re-settable circuit breakers that protect the touchscreens from
power surges.
(3) Fuses/Voltage Selector - Slide out panel which allows the user to select either 110-120 VAC or
220-240 VAC as the input voltage. Fuses protecting the transformer are located here. Refer to
Selecting Input Voltage for Transformers.
(4) Power Input - Main power receptacle. The voltage entering can be 110-120 VAC or 220-240
VAC. Refer to Fuse/Voltage Selector Chart.
Vector Scorers 27
Selecting Input Voltage for the Touchscreen Transformer
WARNING!
Always remove the power cord prior to working on the
Touchscreen Transformer!
To select the input voltage for the touchscreen transformers, do the following:
1. Disconnect the power cord from the transformer.
2. Using a flat head screwdriver, remove the fuse holder from the power receptacle. Refer to figure
titled Selecting Input Voltage for Transformers.
Selecting Input Voltage for Transformers
(1)REMOVE FUSE HOLDER FROM POWER RECEPTACLE
(4) 100v-120v position
(7)voltage designation
(2)FLAT HEAD SCREWDRIVER
(3) indicator
(5) 200v-240v position
(6) fuses
3. Examine the fuses in the holder to verify the proper fuse rating according to the charts below:
INPUT VOLTAGE
FUSE RATING
110 VAC - 120 VAC
.5 AMP 250V Slo Blow
220 VAC -240 VAC
Fuse/Voltage Selector Chart
.25 AMP 250V Slo Blow
4. Insert the fuse holder into the power receptacle with the desired voltage designation positioned
toward the indicator on the receptacle.
5. Connect the power cord to the transformer.
28 Vector Scorers
LCD Touchscreen Adjustment Procedure
Adjustment to the LCD Touchscreen is performed through 4 push-button switches located on the
touchscreen controller PCB. These push-buttons allow the user to access an on-screen adjustment menu
to adjust brightness, contrast, color, and image position. Refer to figure titled Touchscreen Adjustment
Push- Buttons.
Touchscreen Adjustment Push-Buttons
(1) reset
(4)select
(2) up
(3) down
(1) Reset - Use this button to reset all options to factory default settings.
(2) Up - Use this button to increase the setting of the selected option or to move up the selection
menu.
(3) Down - Use this button to decrease the setting of the selected option or to move down the
selection menu.
(4) Select - Use this button to select an option from the menu or to enter the selected setting for an
option.
Vector Scorers 29
The following procedures list the necessary steps required to adjust the image of the flatscreen monitor.
Basic Adjustments
WARNING! Inverter PCB on rear LCD Touchscreen panel contains high
voltage. DO NOT touch inverter PCB when power is on!
1. Remove the four Phillips head screws from the rear cover to gain access to the LCD Console
Controller PCB.
2. Turn on power to flatscreen.
3. Press SEL (select) button on Controller PCB. The main menu will appear.
4. Use the UP and DOWN buttons to highlight the Basic Adjustments menu and press SEL.
There are three basic adjustments that can be made in this mode: brightness, contrast, and color balance.
5. Use UP and DOWN buttons to highlight desired adjustment and then press SEL.
6. To change current setting, use UP to increase setting, DOWN to decrease setting. A numerical
value is displayed next to the bar graph on the screen and updates automatically during
adjustment.
7. Press SEL to enter desired setting.
For example, to change the brightness setting, highlight the Brightness option. Use the UP button to
increase brightness or the DOWN button to decrease brightness. Press SEL when finished to enter
desired setting and exit this adjustment.
The three basic adjustments are factory-set to the following values but can be changed to preference.
The color balance adjustment can be altered for the following colors: red, green, and blue.
Brightness
35
Contrast
50
Color Balance 50 each for red, green, and blue
8. Use UP and DOWN buttons to highlight EXIT option and press SEL to exit the Basic
Adjustments menu.
9. Install the rear cover on the touchscreen.
30 Vector Scorers
Image Position Adjustment
The imagine position adjustment is used to change the position of the viewable image on the screen.
WARNING! Inverter PCB on rear LCD Touchscreen panel contains high
voltage. DO NOT touch inverter PCB when power is on!
1. Remove the four Phillips head screws from the rear cover to gain access to the LCD Console
Controller PCB.
2. Turn on power to touchscreen.
3. Press SEL (select) button on Controller PCB. The main menu will appear.
4. Use the UP and DOWN buttons to highlight the Image Position option.
5. There are four position adjustments:
a.
b.
c.
d.
e.
Horizontal Position
Horizontal Size
Vertical Position
Expand/Center
Phase
6. Use the UP and DOWN buttons to highlight the desired adjustment and press SEL.
7. To change current setting, use UP to increase setting or DOWN to decrease setting. A
numerical value is displayed next to the bar graph on the screen and updates automatically
during the adjustment.
The following values are factory-set but can be changed to preference.
Horizontal Position
Horizontal Size
Vertical Position
Expand/Center
92
50
50
8. Once the desired value is displayed, press SEL to enter the setting and exit the adjustment.
NOTE: After changing the image position settings, it may be necessary to adjust the phase of
screen image ONLY if characters are fuzzy or the screen is jittery.
9. As Needed - Observe screen image and if the screen characters are jittery, perform a phase
adjustment as follows:
a. Using UP and DOWN Push-button, select IMAGE POSITION option.
b. Under IMAGE POSITION option, highlight PHASE and press SEL.
c. Use the UP or DOWN arrow keys until image becomes clear (no fuzziness or jittering).
d. Press SEL to set the phase adjustment.
Vector Scorers 31
10. Use UP and DOWN buttons to highlight Exit option and press SEL to exit the program.
11. Install the rear cover on the touchscreen.
12. If the image position has changed, calibrate the touchscreen using the calibration utility located
on the configuration screen of the scorer computer.
IMPORTANT: DO NOT use menu option “Calibrate Touchscreen.”
LCD Touchscreen Cleaning
The LCD touchscreen uses a custom hard coated antiglare polyester touch surface to protect the screen.
The surface should be kept free of dirt, dust, finger prints, or other materials that could lower the screen
visibility. For best results use a clean, damp, nonabrasive cloth towel and any commercially available
window cleaner to regularly clean the surface.
IMPORTANT: Apply the cleaning solution to the cloth before wiping down the screen. DO NOT
spray the solution directly onto the touchscreen.
Circuit Board and Component Removal
CAUTION: Some circuits and circuit boards in the Scorer Computer or console
may be static sensitive and can be damaged due to improper handling. You
should follow the suggested guidelines to avoid problems.
NOTE: Failure to use proper handling techniques for the circuit board may void the warranty.
1. Before working on or removing any board you MUST discharge any static within your body by
touching the metal chassis of the Scorer Computer or console. (If added protection from static
electricity is desired, wear a grounded wrist strap).
2. Always keep static sensitive boards and components in their protective wrapping when not in
use.
3. Handle the boards by the edges only to avoid damaging the board.
4. Avoid touching the gold plated edge terminals.
5. When handling hard drives, use extra care to ensure that the drive is not dropped or handled
roughly. Even slight jarring of the drive could cause damage.
32 Vector Scorers
Before replacing any component, you must determine if it requires any initial setup. Refer to the chart
titled Configuration Chart.
Component
Setup Required Setup/Comments
Hard Drive
Yes
1. Set Scorer Computer configuration using the Configuration Menu at the
console (Default Password: Keypads = /Vector, Flatscreens = 939393)
2. Download Updated software from the Server Computer. (Scorer Update)
3. Download Commercials From the Server Computer. (Scorer Update)
4. Download Multimedia from the Server Computer. (Scorer Update)
5. Synchronize the control desk and Scorer Computer information.
6. Calibrate the Camera’s (if installed) for all lanes associated with the hard
drive using the Pin Settings page at the control Desk
7. Calibrate each touchscreen for lanes associated with the hard drive using
using the Configuration Menu at the console.
(Default Password: Keypads = /Vector, Flatscreens = 939393)
8. Enable automated bumpers (if installed) using config.exe program at server.
Keypad
Interface PCB
Yes
Set the jumper on the board as follows:
JP4 - If the global audio cable does not continue to another console from J6,
position jumper at pins 2 and 3 (T). If the global audio cable continues
to another console from J6, position jumper at pins 1 and 2 (U).
LCD Console
Controller
Yes
Set the jumpers on the board as follows:
JP1 - Position jumper at pins 1 and 2 (U)
JP7 - Position jumper at pins 1 and 2 (L)
JP8 - If the global audio cable does not continue to another console from J2,
position jumper at pins 2 and 3 (T). If the global audio cable continues to
another console from J2, position jumper at pins 1 and 2 (U).
JP9, JP10 - Position jumper at RS232
LCD Interface
PCB
No
Motherboard
No
1. Transfer DIMM memory module from original motherboard (if needed).
2. Transfer CPU from original motherboard (if needed).
3. Verify proper cable connections
Power Supply
No
Verify the power cables are connected properly to the Motherboard, Hard Drive,
Patch Panels, and LCD Interface as needed.
Primary Patch
Panel
No
Connect cables as needed. Make sure power cable is connected properly.
Secondary
Patch Panel
No
Connect cables as needed. Make sure power cable is connected properly.
Touchscreen
Transformer
Yes
Set the Transformer to the appropriate voltage setting and install proper fuses.
Video3 PCB
Yes
- Video3 PCB connected to the Primary Patch Panel
JP1 - Remove
JP2 - Remove
JP3 - Remove
JP4 - Remove
- Video3 PCB connected to the LCD Interface PCB / Secondary Patch Panel
JP1 - Remove
JP2 - Install
JP3 - Remove
JP4 - Remove
Configuration Chart.
2. Verify ribbon cables are plugged into the correct connectors.
3. Calibrate cameras at the control desk if the PCB has cameras attached. (If
needed, adjust brightness control for boards that have pin cameras attached.
Vector Scorers 33
Motherboard Removal
Before removing the Motherboard, the boards that connect to it must be removed. Refer to figure
procedure PCI Bus Board Removal.
Perform the following steps to remove the Motherboard:
1. Turn off the Scorer Computer using the main power switch located on the side of the chassis
and remove the power cord from the power supply.
2. Discharge any static electricity by touching the metal chassis of the Scorer Computer.
3. Remove each PCI Bus Board. Refer to procedure titled PCI Bus Board Removal. Note the
location of each PCB removed.
4. Disconnect the following cables from the motherboard:
Power switch cable
Audio cable
COM1 cable
COM2 cable
Hard Drive data cable
Power supply power cable(s)
5. Remove the screws that hold the Motherboard to the chassis.
6. Place the Motherboard in an antistatic bag or wrapping.
Motherboard Installation
1. Turn off the Scorer Computer using the main power switch located on the side of the chassis
and remove the power cord from the power supply.
2. Discharge any static electricity by touching the metal chassis of the Scorer Computer.
3. At the Scorer Computer, remove the Motherboard from the antistatic bag or wrapping.
4. Secure the Motherboard to the chassis with the Phillips head screws.
5. If needed, transfer the RAM memory (DIMM chips) from the old Motherboard to the new
Motherboard.
6. If needed, transfer the processor chip (CPU) and its fan from the original motherboard to the
new motherboard.
NOTE: If transferring the CPU from the original motherboard to the new motherboard be sure
to position the chip properly in the CPU socket and properly connect the CPU fan.
34 Vector Scorers
7. Connect the following cables to the Motherboard:
Power switch cable
Audio cable
COM1 cable
COM2 cable
Hard Drive ribbon cable
Power supply power cable(s)
8. Install each PCI Bus Board in the same slot from which they were removed and attach the
appropriate cable to each. Refer to procedure titled PCI Bus Board Installation.
9. Verify that each board and connector is properly installed.
NOTE: The motherboard bios default configuration is programmed with the proper settings
to function with the Vector scoring system. The steps 10 -20 are only needed if these factory
settings have been changed.
10. Connect a standard PS-2 style keyboard and VGA monitor to the
motherboard as shown below:
(2)
KEYBOARD
CONNECTOR
+12v
POWER
MOUSE
(GREEN)
ATX POWER
KB
(PURPLE)
USB PORTS
DVI
(WHITE)
1
REAR L/R
(BLACK)
MIC-IN
(PINK)
IDE
DDR2-3
DDR2-4
CPU
FAN
LAN2
SIDE L/R
(LT BLUE)
DDR2-1
LAN
USB
PORTS
DDR2-2
(1)
MONITOR
CONNECTOR
VGA
(BLUE)
CENTER/SUB
(ORANGE)
LINE-OUT
LINE-IN
(LIME)
(LT. BLUE)
CD-IN
PCIE / DVI
SELECT (Jp8)
FDD
PCIE 1
PCIE 2
2ND FAN
PCI 1
SATA 1
SATA 0
SATA 3
SATA 2
SYSTEM FAN
SATA 5
SATA 4
PCI 2
PCI 3
PCI 4
USB 7-8 USB 1-2
STANDBY POWER LED
COM 2
COM 1
DIO
PARALLEL
USB 4-5
ATX
SW
FRONT PANEL
Connecting a Keyboard and Monitor to The Scorer Computer
(1) monitor connection
(2) keyboard connection
11. Connect the power cord to the power supply receptacle and turn the Scoring Computer using
the main power switch.
Vector Scorers 35
12. Press <Del> to enter the Bios utility. The main menu screen will appear.
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
Standard CMOS Features
CPU Frequency Control
Advanced BIOS Features
Load Fail-Safe Defaults
Advanced Chipset Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP/PCI Configurations
Save & Exit Setup
PC Health Status
Exit Without Saving
Esc : Quit
F10 : Save & Exit Setup
: Select Item
Time, Date, Hard Disk Type...
Bios - Main Menu Screen
13. On the main menu select Standard CMOS Features.
14. Using the arrow, +, -, Page Up, and Page Down keys move the cursor to Drive A and press
[Enter]. Set Drive A to None.
15. Move the cursor to Halt On and press [Enter]. Set Halt On to No Errors.
36 Vector Scorers
16. Press [ESC] to return to the Main Bios Screen.
Bios Standard CMOS Features
Vector Scorers 37
17. Select the option Advanced Bios Features.
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
Standard CMOS Features
CPU Frequency Control
Advanced BIOS Features
Load Fail-Safe Defaults
Advanced Chipset Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP/PCI Configurations
Save & Exit Setup
PC Health Status
Exit Without Saving
Esc : Quit
F10 : Save & Exit Setup
: Select Item
Time, Date, Hard Disk Type...
Bios - Main Menu Screen
38 Vector Scorers
18. On the Advanced Bios Feature Screen, move the cursor to First Boot Device and press [Enter].
Set First Boot Device to CD-ROM.
Bios - Advanced Feature Screen
19. Move the cursor to Second Boot Device and press [Enter]. Set Second Boot Device to HDD-0.
20. Press [F10] to save the selections, leave the bios setup screens, and reboot the Scorer Computer.
Vector Scorers 39
PCI Bus Board Removal
The PCI Bus Boards are the boards that connect to the white medium sized connectors of the
Motherboard. Since all of these boards are mounted and connected in the same way, their removal is
the same. To remove the PCI Bus Boards, perform the following steps.
1. Turn off the Scorer Computer using the main power switch located on the side of the chassis
and remove the power cord from the power supply.
2. Discharge any static electricity by touching the metal chassis of the Scorer Computer.
3. Disconnect any cables that are attached to the board being removed. Label the cables so that
you can reconnect them properly.
4. Remove the Phillips head screw that holds the board to the Scorer Computer chassis.
5. Carefully remove the circuit board from the Scorer Computer chassis.
6. Place the circuit board in an antistatic bag or wrapping.
PCI Bus Board Installation
IMPORTANT!: When replacing some PCI Bus Boards, special setup and configuration
procedures must be performed. Failure to configure the board properly may result in
inoperative lanes. Within this section, refer to the chart titled Component Setup requirements
for more information.
To install a PCI Bus Board, perform the following steps:
1. Discharge any static electricity by touching the metal chassis of the Scorer Computer.
2. Remove the circuit board from its antistatic bag or wrapping.
3. Determine any special jumper setting that is required for the board. Refer to the chart titled
Determining if a Circuit Board Requires Setup.
4. Configure the board as described in the Circuit Board Setup Procedures section within this
section.
5. Carefully insert the circuit board into the same PCI Slot on the Motherboard.
6. Secure the board to the Scorer Computer chassis with the appropriate Phillips head screw.
7. Connect any cable(s) disconnected during board removal.
8. Connect power to the Scorer Computer.
40 Vector Scorers
Hard Drive Replacement
Perform the following steps to replace the hard drive Refer to figure titled Scorer Computer Hard Drive
Location:
Installation of Hard Drive
1. Turn off the Scorer Computer using the main power switch located on the left side of the
chassis. Remove the power cord from the power supply. Open the cover of the scorer computer.
2. Disconnect the power and data cables from the hard drive.
3. Loosen the phillip head screws that hold the hard drive bracket to computer chassis. Remove
the hard drive and bracket.
4. If the replacement drive is not mounted to a bracket, remove the bracket from the original drive,
and attach it to the replacement drive.
5. Carefully install replacement hard drive and bracket into the Scorer Computer . Tighten the
screw(s) to secure the bracket and drive.
6. Attach the power and data cables disconnected in step 3 to the new hard drive.
8. Connect the power cord the power supply receptacle and turn the Scorer Computer on using the
main power switch.
7. Disconnect the network cable (100base-TX).
(3)
POWER
CONNECTOR
E
OL
NS
O
CO
DE
VI
E
OL
NS
O
CO
DE
VI
E
OL
NS
O
CO
DE
VI
E
OL
NS
O
CO
DE
VI
E
OL
NS
O
CO
DE
VI
E
OL
NS
O
CO
DE
VI
E
OL
NS
O
CO
DE
VI
E
OL
NS
O
CO
DE
VI
(2)
SATA HARD
DRIVE
(1)
DATA
CONNECTOR
8
7
6
5
4
3
2
1
ETWORK
CAMERA 1
CAMERA 2
CAMERA 3
CAMERA 4
Scorer Computer - Hard Drive Location
(1)Data connector
(2)sata hard drive
((3) power connector
Vector Scorers 41
Configure the Hard Drive
IMPORTANT: To get the scorer information to appear on overhead monitors the overhead type
must be set properly. The hard drives cone pre-configured for use with the overhead monitor
type (CRT or LCD) installed in your center. If the hard drive mistakenly becomes configured
for the wrong type AND the center is equipped with keypads , the Ethernet cable must be
plugged into the scorer computer and the overhead type must be changed using the Config.
exe program located at the Vector/Vector Plus server. Failure to configure the overhead in this
way may result in blank overhead screens. This procedure does not apply to installations those
with lower LCD touchscreens as the overhead type can be set through the scorer computer
configuration screen using the touchscreen.
Installations equipped with automatic bumpers must also use the config.exe program to enable
the bumpers.
Select overhead type (If set improperly in centers with keypads) and Bumpers (Installations with
Brunswick automated bumpers)
1. Verify that the Ethernet cable is plugged into the scorer computer and the scorer computer is
turned on.
2. At the Windows desktop screen (the screen with the icons) of the Vector or Vector Plus
SERVER computer, double-click on the “My Computer” icon.
3. Double-click on the ‘C’ drive. Double-click on the “Brunswick” folder , then double-click the
“Utilities” folder. Refer to the figure titled Config.exe screen.
4. Double-click on the Config.exe file.
Config.exe screen
5. Select the Score Computer button.
6. At the message, “Is CMSERVER a scoring computer?” or “Is DATOR a scoring computer?”,
click No. Refer to the figure titled Scorer Configuration Screen.
7. Select the desired Scoring Computer from the drop-down list on the top-left of the window. If
the scorer computer is not on the list, click “Search” to refresh the list.
42 Vector Scorers
NOTE: The default setting for factory hard drives is either Scorer Computer 1 or 9 .
Scorer Configuration Screen
8. In the Lanes column , double-click on the first lane that has bumpers or widescreen overhead
monitors that are set improperly. Refer to the figure titled Lane Configuration Screen.
Lane Configuration Screen
9. If the lane has Brunswick Automated Bumpers, select the appropriate bumper type. If the lane
overhead type is incorrect, use the drop down box next to “Overhead Type” to select VGA as
the overhead type for the widescreen overhead. When finished, click OK.
Vector Scorers 43
10. Repeat steps 8 and 9 for each lane that has automatic bumpers installed. For widescreen
overheads the rest of the lanes for the scorer computer will automatically be switched to the
overhead type selected.
11. Click Save to finish.
12. Click Exit.
13. When prompted select Merge, then click Exit.
Set Scorer Computer Configuration (All installations)
1. After the scorer has booted, press the “Menu” key for keypads, or touch the screen for
touchscreens so that main scorer entry screen is displayed. For keypad installations, access the
Scorer Computer configuration screen by entering the factory default password:
/VECTOR. For touchscreen installations, enter 939393 using the password grid as shown below.
Refer to figures titled Configuration Menu Password - Touchscreen and Scorer Computer
Configuration Screen.
Configuration Menu Password - Touchscreen
2. Enter the Scoring Computer number, the starting lane for that scorer computer, the number of
lanes controlled by that scorer computer, the pinsetter type in use, and a new menu password
as appropriate. The Direct Monitor Ctrl should be selected (checked) for centers that have
the overhead communication cable directly connected to the widescreen monitors. If the
communication cable connects to the Serial Communication Controller (SCC) board inside the
interface box mounted to the back the widescreen overheads, it should be unchecked. If you
have LCD lower screens, Do Not calibrate the touchscreen at this time.
44 Vector Scorers
3. Press OK to reboot the Scorer Computer.
NOTE: Select the overhead type as appropriate, if you select the wrong overhead, type; “the
overhead screens will not properly display the score sheet”.
NOTE: The configuration can be performed at any keypad or touchscreen connected to the
Scorer Computer. This is a one time setup that does not need to be repeated at the other lanes.
Configuration Menu
Scoring Computer #
1
First Lane
1
Number of Lanes
8
Password
Calibrate
Direct Monitor Ctrl
******
Pinsetter
GS
AMF/ No SS
String
Other
5,0,0,0258
OK
OH Type
NTSC
PAL
LCD
PAL/TV
Cancel
Scorer Computer Configuration Screen
4. Reconnect the Ethernet cable if removed in step 7 of the “Installation of Hard Drive”
procedure.
5. If touchscreens are installed, calibrate the touchscreens by entering the Scorer Computer
Configuration menu as described in step 1. Select [Calibrate LCD] and follow the on-screen
instructions. Repeat the procedures at each touchscreen attached to the Scorer Computer.
IMPORTANT!: LCD calibration must be performed at each touchscreen connected to the
Scorer Computer.
Vector Scorers 45
Updated the Drives Programing
Updating the programming of the hard drive involves downloading of new software, commercials
and multimedia files to the Scorer Computer’s drive from the control desk. Once this is complete,
the programs’s settings must be synchronized with the control desk. Finally, if cameras are used for
scoring, they need to be calibrated using the Pin Settings screen at the control desk.
1. From the control desk, update the software, commercials and multimedia. Refer to the
“Updating Scorer Software” procedure located in the “Vector/Vector Plus Control Desk”
Section of this manual. Reboot the Scorer Computer after the updates have finished.
2. Synchronize the Scorer Computer to the control desk. Refer to the “Scorer Computer
Synchronization” procedure.
3. If pin cameras are used for scoring, calibrate the cameras using the “pin settings” screen located
at the control desk. Refer to the “Pinsettings and Camera Calibrations” procedures located in
the “Vector Camera Assembly” section of this manual.
4. Reboot the Scorer Computer and verify its operation.
Scorer Computer Synchronization
After replacing the hard drive or updating the software on the Scorer Computer, the control desk
computer and the Scorer Computer must be synchronized. To synchronize them perform the following
steps:
Vector Version 3.0 or prior
1. Wait until the Scorer Computer(s) have restarted and the communication back (i.e. green bars)
on the Vector Lane Status Screen have appeared.
2. Click on the Settings menu and choose Setup from the drop down menu.
3. Verify that the fields on each tab selection are set as desired.
46 Vector Scorers
4. Select the Intercom and Service Tab click the Browse button (small box with three dots) that is
located in the Service Request area. Refer to figure titled Intercom and Service Tab.
Intercom and Service Tab
5. Double click on the File Red.bmp or select a file of your choice and click OK.
6. From the Setup window, Click the OK button again. The Vector program will restart
automatically.
7. Click on the Settings menu and choose Lane settings from the drop down menu. Verify that
the options are set as desired. Click the OK button.
NOTE: If you need to update more than one scoring computer you will need to update each
lane range separately. Use the Apply button instead of the OK button until you are on the last
lane range tab, then use OK.
8. Click on the Settings menu and choose Volume from the drop down menu.
9. Adjust the slide bar to the desired level and click the OK button.
Vector Scorers 47
10. Press the F7 function key, highlight American League, and click the OK button.
11. Click the Config button, the OK button and then the Cancel button.
12. Press the F2 key to display the Open Play window. Ensure that there is no personnel or
equipment on the lanes or the pinsetters. In the Lane text box type in the lane range for the
center i.e. 1-24, then select Start.
13. Verify that all the lanes turn on with score sheets.
14. Click on the Stop button in the top right corner and type in the lane range for the center in
Lanes text box. Click the OK button to shut down all the lanes.
Vector Version 3.2 or higher
1. Wait until the Scorer Computer(s) have restarted and the communication back (i.e. green bars)
on the Vector Lane Status Screen have appeared.
2. Click on the Service menu and choose Resyc Scorers from the drop down menu.
Vector Plus
1. Using each of the Vector Settings buttons located on the Lane Status screen, send the desired
selection settings to the scorer computer.
48 Vector Scorers
Cabling Overview
Scoring Computer Cabling - Keypads, Non-GS Pinsetters and Wide Screen Overhead Monitors
(1) Scoring computer
(4) keypad
(7)CAMERA VIDEO CABLES
(10) keypad control cable
(2) triple wide screen
(3) rs 232 converter
overhead monitors w/tv only
(5) CAMERA
(6)OVERHEAD VIDEO CABLES
(8) SCANNER DATA CABLES
(9) control CABLE
(11)PRIMARY PATCH PANEL
Vector Scorers 49
Scoring Computer Cabling - Keypads, GS Pinsetters, and Wide Screen Overhead Monitors
(1) Scoring computer
(2) triple wide screen overhead (3) rs 232 converter
monitors w/tv only
(4) keypad
(5) control CABLE
(6)OVERHEAD VIDEO CABLES
(7) gs nexgen electronics (8) pinsetter DATA CABLES
(9) keypad control cable
(10)PRIMARY PATCH PANEL
50 Vector Scorers
Scoring Computer Cabling - LCD Touchscreen, Non-GS Pinsetters and Wide Screen Overhead Monitors
(1) Scoring computer
(2) triple wide screen overhead
(3) rs 232 converter
monitors w/tv only
(4) lcd touchscreen
(5) CAMERA
(6)OVERHEAD VIDEO CABLES
(7)CAMERA VIDEO CABLES
(8)DISTRIBUTION DATA/POWER CABLE (9)LCD TOUCHSCREEN VIDEO CABLES
(10)LCD TOUCHSCREEN CONTROL(11) control CABLE
(12)PRIMARY PATCH PANEL
CABLE
(13) SECONDARY PATCH PANEL
Vector Scorers 51
Scoring Computer Cabling - LCD Touchscreen, GS Pinsetters and Wide Screen Overhead Monitors
(1) Scoring computer
(2) triple wide screen overhead (3)rs 232 converter
monitors w/tv only
(4) lcd touchscreen
(5) control CABLE
(6)OVERHEAD VIDEO CABLES
(7) gs nEXGEN ELECTRONICS
(8)PINSETTER DATA CABLE
(9)LCD TOUCHSCREEN VIDEO CABLES
(10)LCD TOUCHSCREEN CONTROL(11)PRIMARY PATCH PANEL
CABLE
(12) SECONDARY PATCH PANEL
52 Vector Scorers
Vector Keypad Lane Pair Cables - Non-GS Pinsetters with WideScreen Overhead Monitors
(1)sCORING COMPUTER (2)TRIPLE wide screen (3) odd lane
OVERHEAD MONITORS
(4) even lane (5)CAMERA
(6)MASKING UNIT
(7) 57-500399-000 Scoring (8) 27-619054-000 global audio (9) 57-5000523-000 tv video
computer to KEyPAD BULK CABLE to control desk overhead to OVERHEAD LAN CABLE cable cable
(10) 57-500492-000 control cable (11) 57-500207-000 FOUL CABLE
(12) 57-500050-000 camera video
OVERHEAD TO OVERHEAD cable
(13) 57-500281-000 camera dATA
(14) 57-30110-000 global audio
(15) TEL- E-FOUL
CABLE cable
(16) 57-500460-148 or 57-500256-000 (17)PKG. 57-863173-000, P/N (18) 57-500220-000 Ball Detect
overhead video cable 57-300659-000 ball detect cable
(19)TO NEXT LANE PAIR
(20) 57-301111-000 global audio (21) 57-500278-000 lane cable
(22) to scorer computer (23) to peripherals
(24) 57-500491-000 control cable CABLE to overhead
(25) 57-500279-000 LANE Cable Vector Scorers 53
Vector Keypad Lane Pair Cables - GS-X Pinsetter with Wide Screen Overhead Monitors
(1)sCORING COMPUTER (2)TRIPLE Wide Screen (3) odd lane TABLE
OVERHEAD MONITORS
(4) even lane TABLE
(5)TO NEXT LANE PAIR (6)GS-X PINSETTER
(7) 57-500310-000 scoring computer (8) 27-619054-000 global audio (9) 57-5000523-000 TV VIDEO
to KEyPAD CABLE BULK CABLE to control desk overhead TO OVERHEAD CABLE
(10) 57-500492-000 OVERHEAD TO (11)RS-232 CONVERTER
(12) 57-500063-000 gs-pinsetter
OVERHEAD CONTROL cable rs-232/485 cable
(13) 57-500279-000 LANE CABLE (14) 57-310110-000 GLOBAL AUDIO (15) 57-500278-000 LANE CABLE
(16) 57-301111-000 GLOBAL AUDIO
(17) to scorer computers
(18) to peripherals
(19) 57-500491-000 CONTROL CABLE (20) 57-500460-148 or 57-500256-000
RS-232 CONVERTER TO OVERHEADOVERHEAD VIDEO CABLE
54 Vector Scorers
Lane Pair Cabling - Non-GS Pinsetters - LCD Touchscreen Wide Screen
(1) 57-500275-000 SCORING (2) 57-500360-000 SCORING
(3)ODD LANE TOUCHSCREEN
COMPUTER TO LCDCOMPUTEr TO LCD
TOUCHSCREEN LAN CABLETOUCHSCREEN VIDEO CABLES (4) 57-500460-148 or 57-500256-150 (5) SCORING COMPUTER
(6) 57-300153-000 lcd touchscreen
OVERHEAD video CABLES power CABLE
(7)TO NEXT LANE PAIR
(8) TRIPLE LCD Wide Screen (9) EVEN LANE TOUCHSCREEN
overheads (10) 57-301110-000 GLOBAL AUDIO (11) 57-500274-000 LANE CABLE (12) camera
LANE PAIR TO LANE PAIR
(13) 57-500491-000 CONTROL cable (14) 27-619054-000 BULK GLOBAL (15) lcd touchscreen RS-232 CONVERTER TOAUDIO FROM DESK power supply
OVERHEAD
(16) 57-500050-000 camera video (17) 57-500281-000 camera data (18) tel-e-foul
cable cable
(19) 57-500207-000 foul cable (20) 57-500492-000 OVERHEAD TO(21) 57-500220-000 BALL DETECT
OVERHEAD CONTROL CABLECABLE
(22) BALL DETECT 57-300659-000
(23) 57-500273-000 lane cable (24) 57-301111-000 global audio
(25) to scorer computer
(26) to peripherals
(27) 57-500523-000 TV VIDEO OVERHEAD TO OVERHEAD
Vector Scorers 55
LCD Touchscreen with GS-X Pinsetters - Lane Pair Cabling (Wide Screen)
(1) 57-500275-000 SCORING COMPUTER (2) 57-500360-000 or 57-500827-000(3)ODD LANE TOUCHSCREEN
TO LCD TOUCHSCREEN LAN CABLELCD TOUCHSCREEN VIDEO
CABLES
(4) 57-500460-148 or 57-500256-150 (5) SCORING COMPUTER
(6) 57-300153-000 lcd OVERHEAD Video CABLES touchscreen power CABLE
(7)TO NEXT LANE PAIR
(8) TRIPLE LCD Wide Screen (9) EVEN LANE TOUCHSCREEN
overheads
(10) 57-301110-000 GLOBAL AUDIO LANE (11) rs-232 convertEr
(12) 57-500063-000 gs PAIR TO LANE PAIR 57-863244-000 pinsetter rs232 convertor
(13) 57-500491-000 CONTROL cable (14) 27-619054-000 BULK GLOBAL (15) lcd touchscreen RS-232 CONVERTER TO OVERHEADAUDIO FROM DESK power supply
(16) gs-X pinsetter
(17) 57-500273-000 lane cable
(18) 57-301111-000 global audio
(19) 57-500274-000 LANE CABLE
(20) 57-500523-000 tV VIDEO (21) to scorer computer
OVERHEAD TO OVERHEAD
CABLE
(22) to peripherals
(23) 57-500492-000 OVERHEAD TO
OVERHEAD CONTROL CABLE
56 Vector Scorers
Global Video Cabling for Typical 16 Lane Center (Wide Screen)
(1) VIDEO AMPLIFIER
(2) rg-6 OVERHEAD video cable bulk (57-500494-000)
(4) 32” OR 40” lcd wide screen (5) 57-500523-000
overheads
(7)CENTER OF HOUSE
(8)CABLE (57-500523-000) OUT TO NEXT OVERHEAD OR VIDEO TERMINATOR
(11-697009-000) AT LAST OVERHEAD
(3) control desk
(6) 57-500524-000
Vector Scorers 57
(2)
SCORING
COMPUTER
(3)
ETHERNET SWITCH
(1)
57-500256-200
Control Desk to Ethernet Switch Cable Routing
(1) 57-500256-200 ethernet cable (2)scoring computer (8 lanes)(3)ETHERNET SWITCH
58 Vector Scorers
Scoring Computer Network 8 Lane Configuration
(1)scoring computer
(2) ethernet switch
(3) 57-500256-007 ethernet cable (7’)
(4) 57-500256-050 ethernet cable (5) 57-500256-100 ethernet
(6) 57-500256-150 ethernet cable
(50’) cable (100’) (150’)
(7) to control desk 57-500256-200 (8) lanes 49-56
(9) lanes 41-48
(200’)
(10) lanes 33-40
(11) lanes 25-32
(12) lanes 17-24
(13) lanes 9-16
(14) Lanes 1-8
(15) 8 lanes per center
Vector Scorers 59
Cable Diagrams
LCD Touchscreen Power Cable (Part No. 57-300153-000)
(1) to j7 on console
(2) 18 volts alternating (3) center
controller pcb current
(4) 18 volts alternating current (5) to lgp transformer
Global Audio lane to Lane Cable (Part No. 57-301110-000)
(1) to j1 audio in on 57-301104-000(2)DRAIN
(3) NO CONNECTION
lcd console control pcb
(4)ICM 1 +
(5)ICM 1 -
(6)ICM 2 +
(7)ICM 2 -
(8) global audio +
(9) global audio (10) j1 audio in
(11) j2 audio out
(12) to j2 audio out on 57-301104-4xx lcd console
control pcb
Global Audio Odd to Even Cable - Pedestal Mount (Part No. 57-301111-000)
(1) to j1 audio in on 57-301104-000 (2)DRAIN
(3) NO CONNECTION
lcd console control pcb
(4)ICM 1 +
(5)ICM 1 -
(6)ICM 2 +
(7)ICM 2 -
(8) global audio +
(9) global audio (10) j1 audio in
(11) j2 audio out
(12) to j2 audio out on 57-301104-4xx lcd console control pcb
60 Vector Scorers
Camera Video Cable (Part No. 57-500050-000)
(1) to camera 1-4 on lane server (2) video
(4) to camera on scanner
(3)shield
GS-Pinsetter RS232/485 Cable (Part No. 57-500063-000)
(1) to rs232/485 converter
(2)shell
(3) drain
(4)no connection
(5) lan a
(6) lan b
(7) +12 volts direct current (8) ground
(9) chassis
(10) to P8 (comline in) on GS-98 direct
or p8 on (scorer comline in) on
Gs-x
Foul Cable (Part No. 57-500207-000)
(1) to distribution board j5 (2) left foul +
(4) right foul + (5)RIGHT FOUL -
(7)OR +12 volts direct current(8)RIGHT
(10)TO FOUL UNIT
(3) left foul (6)GROUND
(9)LEFT
Vector Scorers 61
Power Control Cable (Part No. 57-500235-000)
(1) No connection
(2)Comm
(3) Normally open
Audio Cable (Part No. 57-500240-000)
Primary Patch Panel PCB Power Cable (Part No. 57-500241-000)
(1)TO J24 ON PRIMARY PATCH PANEL (2)TO SCORER COMPUTER POWER
SUPPLY CONNECTOR
62 Vector Scorers
LCD Touchscreen Transformer (Part No. 57-500242-000)
(1)scanner power
(2) mini-console circuit breaker
(3) mini-console power
(4)POWER RECEPTACLE
(5)TRANSFORMER
Overhead Video Ribbon Cable (Part No. 57-500245-000)
Vector Scorers 63
COM1 Ribbon Cable (Part No. 57-500251-000)
(1)RED STRIPE PIN #1
(2) 10 - nO connection
Ethernet Cable / CAT5e Widescreen Video Cable (Part No. 57-500256-xxx)
(1)TO SCORING COMPUTER
(2)TO ETHERNET SWITCH OR TO J1
ON VGA ADAPTER BOARD (vab)
LAN Cable Odd Even Lane - Touchscreen Pedestal Mount (Part No. 57-500273-000)
(1)TO ODD LANE TOUCHWORX PCB
(4)RX EVEN
(7)GROUND
64 Vector Scorers
(2)CHASSIS GROUND
(5)TX EVEN
(8)EVEN LANE J /J9
(3)ODD LANE J5/J10
(6)EXCITER EVEN
(10)TO EVEN LANE TOUCHWORX PCB
LAN Cable Odd Even Lane - Table Mount (Part No. 57-500274-000)
(1)TO ODD LANE TOUCHWORX PCB(2)CHASSIS GROUND
(4)RX EVEN
(5)TX EVEN
(7)GROUND
(8)EVEN LANE J /J9
(3)ODD LANE J5/J10
(6)EXCITER EVEN
(10)TO EVEN LANE TOUCHWORX PCB
Scorer Computer to Odd Lane LCD LAN Cable (Part No. 57-500275-000)
(1)TO KBD14 ON LANE SERVER
(2) SHELL
(4)DRAIN
(5)RX ODD
(7)EXCITER ODD
(8)GROUND
(10)TX EVEN
(11)EXCITER EVEN
(13)CHASSIS
(14)GROUND
(16)J4/J9 - ODD LANE
(17)TO J9 ODD LANE
TOUCHWORX PCB
(3)no CONNECTION
(6) TX ODD
(9)RX EVEN
(12)GROUND
(15)CONSOLE
(18)TO J4 ODD LANE
Vector Scorers 65
LAN Cable Odd to Even Lane- Pedestal Keypad Mount (Part No. 57-500278-000)
(1)TO j4 odd lane keypad pcb (2)RX EVEN
(4) + 12 volts
(5)GROUND
(7) audio ground
(8)CHASSIS
(10) j3 even lane
(11)DRAIN
(13) to j3 even lane keypad pcb
(3)TX EVEN
(6) sound even
(9) j4 odd lane
(12)no connection
LAN Cable Odd to Even Lane Cable - Keypad Table Mount (Part No. 57-500279-000)
(1) to j4 odd lane keypad pcb (2) j4 - odd lane (4) drain
(5)no connection
(3) j3 even lane
(6) to j3 even lane keypad pcb
Camera Data Cable (Part No. 57-500281-000)
(1) to dist. 1-4 on lane server (2)no connection
(3)DRAIN
(4) SHELL (5)DISTRIBUTION
(6)RXD
(7)TXD
(8)GROUND
(9) + 12 VOLTS
(10) + 5 VOLTS
(11)CHASSIS GROUND
(12)TO J7 ON DISTRIBUTION BOARD IN SCANNER
Primary Patch Panel to Video3 PCB Ribbon Cable (Part No. 57-500282-000)
66 Vector Scorers
Power Cable (Part No. 57-500299-000)
LAN, Scorer Computer to Keypad with Audio Cable (Part No. 57-500399-000)
(1) to KBD 1-4 on lane server
(4) SOUND ODD
(7)TX ODD
(10)RX EVEN
(13)CHASSIS GROUND
(2)DRAIN
(5)AUDIO GROUND
(8) +12 VOLTS
(11)TX EVEN
(14)CONSOLE
(3) SHELL
(6)RX ODD
(9)GROUND
(12) SOUND EVEN
(15)J3-ODD LANE
RS-232 Converter to LCD Wide Screen Overhead Serial Control Cable (Part No. 57-500491-000)
(1) to rs-232/485 converter
(2) to LCD OVERHEAD
Vector Scorers 67
LCD Wide Screen Overhead to LCD Wide Screen Overhead Serial Control Cable (Part No. 57-500492-000)
(1) to serial communications
controller
LCD Wide Screen Overhead to LCD Wide Screen Overhead TV Video Cable (Part No. 57-500523-000)
LCD Wide Screen Overhead to LCD Wide Screen Overhead Serial Control Cable (Part No. 57-500525-000)
(1) to serial communications
controller
68 Vector Scorers
LCD Wide Screen Scorer Computer to LCD Touchscreen Video Cable (Part No. 57-500827-000)
(1)TO p1 on lcd video control pcb(2) to vector SCORER COMPUTER
Vector Scorers 69
Vector Scoring Computer with Keypads
(1)hard drive (2) power supply
(3) mother board
(4) com 1 TV-ONLY / WIDESCREEN (5) line-out
(6) on/off
CONTROL
(7) com 2 BUMPERS
(8) VIDEO3 (9)EXCITER AUDIO
(10)PRIMARY PATCH PANEL
(11)ETHERNET FILTER
(12)PIN CAMERA INPUT
(13)DISTRIBUTION/GS
(14)KEYBAORD/LCD (15)OVERHEAD VIDEO / EXCITER
COMMUNICATIONCOMMUNICATIONAUDIO SELECT
70 Vector Scorers
Vector Scoring Computer Lower LCDs
(1)hard drive (2) power supply
(3) mother board
(4) com 1 TV-ONLY
(5) line-out
(6) on/off
WIDESCREEN CONTROL
(7) com 2 BUMPERS
(8) VIDEO3 (9)EXCITER AUDIO
(10)PRIMARY PATCH PANEL
(11)ETHERNET FILTER
(12)PIN CAMERA INPUT
(13)DISTRIBUTION / GS (14) kEYBOARD / lcd (15)LOWER VIDEO
COMMUNICATIONCOMMUNICATION
(16) VIDEO OUT
(17) SECONDARY PATCH PANEL(18)OVERHEAD VIDEO /
(19) lcd interfaceEXCITER AUDIO SELECT
Vector Scorers 71
LCD Console Cabling Assembly
(1) touchscreen
(2) lcd panel
(3) lcd video control pcb
57-301101-400
(4) com cn1 57-500363-400
(5) left lane
(6) right lane
(7) audio control unit
(8) 27-609941-000
(9) global audio
(10) 27-609941-000
(11)COMMUNICATION
(12) 57-500273-000 or 57-500274-000
(13)no connection
(14)scoring computer
(15)video57-500360-000
(16) 57-500275-000
(17) 57-300153-000
(18) power transformer
(19)POWER INVERTER
72 Vector Scorers
Keypad Console Cabling Assembly
(1)LEFT LANE KEYPAD INTERFACE(2)RIGHT LANE KEYPAD INTERFACE (3)SPEAKER
PCBPCB
(4)MICROPHONE
(5)KEYPAD
(6)SCORER COMPUTER
(7) audio CONTROL UNIT
(8) global audio
(9)RS-232 COMM/EXCITER AUDIO/
POWER
(10) 27-609941-000
(11) global audio to next lane pair
Vector Scorers 73
Intentionally Blank Page
74 Vector Scorers
">