EBN | POS-7015EG-370 | Service manual | EBN POS-7015EG-370 Service manual

EBN Technology Corp.
Service Manual
Solid POS 70 Series
*POS-7012EG-370
*POS-7015EG-370
March 2007
©Copyright 2007 by EBN Technology Corp. All Rights Reserved.
3/20/2007
1/84
Rev. 1.1
EBN Technology Corp.
Contents
1
2
Chapter 1 : Troubleshooting ........................................................................................................... 4
1.1 Symptoms and Solutions .......................................................................................................... 4
1.2 BIOS Upgrade ......................................................................................................................... 7
Chapter 2 : Disassembly , Assembly............................................................................................... 9
2.1 Main Unit ................................................................................................................................ 9
2.1.1
2.1.2
Front Bezel + Sponge Bezel .................................................................................... 9
Touch Panel + Touch Screen Holder...................................................................... 10
2.1.3
LCD, AUO 15” 1024 x 768 ................................................................................... 12
2.1.4
MSR (Refer to 2.5.4)............................................................................................. 13
2.1.5
Mother Board (Refer to 2.3) .................................................................................. 13
2.1.6
EMI Chassis.......................................................................................................... 14
2.1.7
Key Lock Set ........................................................................................................ 15
2.2 Base Unit............................................................................................................................... 18
2.2.1
Base Housing ........................................................................................................ 18
2.2.2
Swivel Housing Rear / Front ................................................................................. 21
2.2.3
P/S 220W W/PFC.................................................................................................. 22
2.2.4
I/O Board .............................................................................................................. 25
2.2.5
Jumper Cover........................................................................................................ 27
2.3 Boards ................................................................................................................................... 28
2.3.1
Main Board ........................................................................................................... 28
2.3.2
Bridge Board......................................................................................................... 30
2.3.3
Inverter ................................................................................................................. 31
2.3.4
Touch Control Board ............................................................................................. 32
2.3.5
Button Board (For POS 75) ................................................................................... 33
2.4 Cables ................................................................................................................................... 34
2.4.1
Cable, M/B To Inverter.......................................................................................... 34
2.4.2
Cable, M/B To Touch Control BD ......................................................................... 35
2.4.3
Cable, M/B To Speaker ......................................................................................... 37
2.4.4
Cable, M/B To I/O BD 100P ................................................................................. 38
2.4.5
Cable, M/B To HDD 80P....................................................................................... 39
2.4.6
Cable, 2nd VGA to I/O Board................................................................................ 39
2.4.7
Cable, M/B To I/O BD 20P USB ........................................................................... 41
2.4.8
Cable, M/B To Button Board ................................................................................. 41
2.4.9
Cable, LCD to Bridge Board ................................................................................. 42
2.5 Main & Base Unit assembly .................................................................................................. 44
2.6 Accessories............................................................................................................................ 47
3/20/2007
2/84
Rev. 1.1
EBN Technology Corp.
3
2.6.1
2.6.2
HDD ..................................................................................................................... 47
Pole Display.......................................................................................................... 48
2.6.3
2.6.4
MSR ..................................................................................................................... 51
MSR+ I Button...................................................................................................... 53
2.6.5
MSR+ Smart Card................................................................................................. 55
2.6.6
2.6.7
2nd Display W/ Touch........................................................................................... 59
RFID..................................................................................................................... 65
2.6.8
Compact Flash ...................................................................................................... 67
2.6.9
Smart Card ............................................................................................................ 69
2.6.10
2.6.11
I Button................................................................................................................. 71
Mini PCI Wireless LAN ........................................................................................ 73
Chapter 3 : Spare parts list............................................................................................................ 76
3.1 Main Unit .............................................................................................................................. 76
3.1.1
Explode of Main Unit............................................................................................ 76
3.1.2
Main Unit Parts list & quotation............................................................................ 76
3.2 Base Unit............................................................................................................................... 78
3.2.1
Explode of Base Unit ............................................................................................ 78
3.2.2
Base Unit Parts list & quotation............................................................................. 79
3.3 Cables ................................................................................................................................... 79
3.4 Accessories............................................................................................................................ 81
3.4.1
Power Cord ........................................................................................................... 81
3.4.2
HDD ..................................................................................................................... 81
3.4.3
Pole Display.......................................................................................................... 81
3.4.4
MSR ..................................................................................................................... 82
3.4.5
2nd Display........................................................................................................... 82
3.4.6
OS......................................................................................................................... 83
3.4.7
RFID..................................................................................................................... 83
3.4.8
Compact Flash ...................................................................................................... 83
3.4.9
Memory ................................................................................................................ 83
3.4.10 Smart Card +MSR 3T RS232 ................................................................................ 83
3.4.11
I Button +MSR 2T KB .......................................................................................... 84
3.4.12 Wireless LAN ....................................................................................................... 84
3/20/2007
3/84
Rev. 1.1
EBN Technology Corp.
1
Chapter 1 : Troubleshooting
1.1 Symptoms and Solutions
Error Code
Symptom
Check Points
Detail Steps
1. Check LED Light (Upper Left) should be on
2. If yes to item 1, open upper case, check if RAM well plugged
on the memory slot
1001
NO BOOT with
Power On
1.RAM
3. Check golden finger cleanness, if not clean, use pencil eraser
2.CPU
to clean golden finger
3.MB(2.3.1)
4. If still fail, replace with another RAM for testing
5. If fail, replace with another CPU for testing
6. If fail, replace with another mother board for testing
7. If fail, RMA system to EBN
1. Power cord
2. Power button
board (2.3.5)
3. Power button
1002
NO POWER
cable(2.3.7.8)
4. MB (2.3.1)
5.Power
Supply(2.2.3)
1. Check Power Cord is well plugged or not
2. If yes to item 1, open upper case, check if power button
damaged, if yes, replace with another power button board (POS
75) or replace with another MB(POS 72)
3. If power button not damaged, check if power button cable to
MB well plugged.
4. If fail, replace with another power button cable
5. If fail, replace with another MB(POS 75) for testing
6. If fail, replace with another power supply for testing
7. If fail, System RMA to EBN
1. Check golden finger cleanness, if not clean, use pencil eraser
1003
System HANG
Up
1.RAM
2.CPU
3.MB(2.3.1)
to clean golden finger
2. If still fail, replace with another RAM for testing
3. If fail, replace with another CPU for testing
4. If fail, replace with another mother board for testing
5. If fail, System RMA to EBN
1. Shut Down Power
1.Bridge Board to
LCD Cable(2.3.7.9)
1004
LCD Blank
2.Bridge Board
(2.3.2)
3.MB(2.3.1)
2. Open upper case, check cable between bridge board and LCD
well connected or not.
Replace with another LCD cable for
testing
3. If fail, replace with another bridge board
4. If fail, replace with another mother board
5. If fail, System RMA to EBN
3/20/2007
4/84
Rev. 1.1
EBN Technology Corp.
Error Code
Symptom
Check Points
Detail Steps
1. Shut down power
1005
LCD Turn
Black
1. Inverter to LCD
2. Open upper case, check cable between inverter and LCD well
cable,
connected or not.
2. Inverter to MB
4. If fail, check cable between inverter and mother board well
cable, (2.3.7.1)
connected or not.
3. Inverter board
for testing
4. MB(2.3.1)
5. If fail, replace with another inverter board for testing
5. LCD(2.1.3)
6. If fail, replace with another mother board for testing
Replace with another inverter and MB cable
7. If fail, System RMA to EBN
1. Shut down power
2. Open HDD Cover, check HDD 80pin cable and HDD power
1006
HDD Unstable
1. HDD (2.5.2)
cable well connected or not
2. HDD Cable
3. If fail, replace with another HDD for testing
(2.3.7.5)
4. If fail, open upper case, check cable between HDD and
3. MB(2.3.1)
Mother board well connected or not
5. If fail, replace with another mother board for testing
6. If fail, system RMA to EBN
1. Shut down power
Error Message: 1. On Board
1007
CMOS
Battery(2.3.6)
checksum error 2. MB(2.3.1)
2. Open upper case, check on board battery well connected /
damage or not
3. If fail, replace with another battery
4. If fail, replace with another mother board
5. If fail, system RMA to EBN
1. Reinstall touch driver, working mode select "PnP"
2. If fail, shut down power
3. Open upper case, check if cable between touch panel and
1. Driver (NA)
2. Control board to
MB cable (2.3.7.2)
1008
Touch Fail
3.Touch control
board(2.3.4)
4.MB(2.3.1)
5.Touch panel(2.1.2)
touch control board well connected.(Replace the cable with
touch panel at item 10)
4. If fail, check if cable between touch control board and MB well
connected.
Replace with another touch control board to MB
cable
5. Check if switch (# 3) on touch control board at "On" position
6. If fail, check M/B JP10 jumper setting to 2-3
7. If fail, replace with another touch control board
8. If fail, replace with another M/B for testing
9. Replace with another touch panel for testing
10. RMA system to EBN
3/20/2007
5/84
Rev. 1.1
EBN Technology Corp.
Error Code
Symptom
Check Points
Detail Steps
1. Shut down power
2. Check keyboard cable connection
1009
Boot Up K/B
1.100PIN Cable
Malfunction
2.MB(2.3.1)
3. If fail, replace with another keyboard for testing
4. If fail, open upper case, check 100 pin cable between IO board
and MB well connected or not
5. If fail, replace with another MB for testing
6. If fail, system RMA to EBN
1. Shut down power
2. Check mouse cable connection
1010
PS/2 Mouse
1.100PIN Cable
Fail
2.MB(2.3.1)
3. If fail, replace with another mouse
4. If fail, open upper case, check 100 pin cable between IO board
and MB well connected or not
5. Replace with another MB for testing
6. If fail, system RMA to EBN
1. Shut down power
1. MSR to MB
1011
MSR Fail
Cable(2.5.4)
2. MB(2.3.1)
2. Open upper case, check if MSR cable goes underneath
inverter and well connected to MB location (CN12).
Note: the
cable must go through EMI chassis breach
3. If fail, replace with another MSR
4. If fail, RMA MSR to EBN
1. Shut down power
2. Move to Bottom side, open jumper setting cover, check if
jumper setting same with default setting chart.
1. Jumper setting
1012
COM Port Fail 2. 100PIN cable
3. MB(2.3.1)
Note: If device
connector is with voltage, jumper setting needs to change to 5V
or 12V based on different device definition
3. If fail, open upper case, check 100pin cable to MB well
connected or not
4. If fail, replace with another MB for testing
5. If fail, RMA system to EBN
1. Shut down power
2. Check device cable to USB port well connected or not
1013
USB Fail
1. Device Check
3. If fail, replace with another device
2. USB cable
4. If fail, open upper case, check USB Cable to MB location
3. MB(2.3.1)
(CN11) well connected or not
5. If fail, replace with another MB for testing
6. If fail, RMA system to EBN
3/20/2007
6/84
Rev. 1.1
EBN Technology Corp.
1.2 BIOS Upgrade
1. Boot the system with a bootable floppy disk
a. A Windows 98/ME startup disk can be used
b.Or you can create an MS-DOS startup disk under Windows XP, to create an MS-DOS startup disk
under
Windows XP, right click on the 3 ½ floppy drive icon under my computer and select format. On the
format
dialog box, check the box next to “Create MS-DOS startup disk” and then click the start button to make
a
MS-DOS startup disk..
2. Once you boot off of the bootable floppy disk, replace the bootable floppy disk with the floppy disk
containing
the bios files.
3. To update the BIOS using the example above you would type the following command.
a. A:\F82744 s171r21.rom, then push the enter key.
F82744.exe = BIOS FLASH UTILITY
b. Follow the onscreen prompts to update the BIOS.
4. DO NOT TURN OFF THE POWER or RESET/REBOOT the SYSTEM before the BIOS update is
completed, stopping the BIOS UPATE before it is completed will cause the system to become
non-functional.
3/20/2007
7/84
Rev. 1.1
EBN Technology Corp.
5. Reboot the system once the bios update has been completed.
Note:
The BIOS contained here are exclusively for EBN POS72/75 only. EBN assumes no responsibility for any
damages resulting from improper use or lack of technical expertise.
3/20/2007
8/84
Rev. 1.1
EBN Technology Corp.
2
Chapter 2 : Disassembly , Assembly
2.1 Main Unit
2.1.1 Front Bezel + Sponge Bezel
Item
Photo
Description
1. Use screw driver to open upper case.
1
2. 2 screws needs to be removed
2
1. Remove 2 screws
2. Remove cover bracket
3
1. Remove 2 screws from MSR cover
2. Remove 2 screws from inverter
3. Remove 3 cables from inverter
3
2
1
4
3/20/2007
1. Remove 4 screws
9/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
5
1. Separate front and back cover
6
1. Remove 12 screws
2. Remove speaker tape
7
1. Turn to front side
2. Remove and replace with another
front bezel
2.1.2 Touch Panel + Touch Screen Holder
Item
Photo
Description
1
3/20/2007
1. Follow 2.1.1 item 1 to 7 turn to
Front side and remove front bezel
2. Remove 3 screws
10/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
2
1. Turn to back side and remove tape
3
1. Turn to front side and remove touch
panel module
2. Replace with another touch panel
module
3/20/2007
11/84
Rev. 1.1
EBN Technology Corp.
2.1.3 LCD, AUO 15” 1024 x 768
Item
Photo
Description
1
1. Follow 2.1.2 item 1 to item 3 (action
1)
2. Turn to back side
3. Remove 4 screws
2
3
1. Cut plastic string
1. Remove 2 inverter cables
2. Remove LCD cable from LCD
chassis
3. Remove LCD chassis
1
2
1
4
1. Remove tape
2. Remove LCD cable
2
1
3/20/2007
12/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
5
1. Remove 2 screws from left LCD
holder
2. Remove 2 screws from right LCD
holder
3. Remove and replace with another
LCD
2.1.4 MSR (Refer to 2.5.4)
2.1.5 Mother Board (Refer to 2.3)
3/20/2007
13/84
Rev. 1.1
EBN Technology Corp.
2.1.6 EMI Chassis
Item
Photo
Description
1
1. Remove 2 screws
2
1. Open upper case
2. Remove 7 screws
3
1. Remove and replace another EMI
chassis
3/20/2007
14/84
Rev. 1.1
EBN Technology Corp.
2.1.7 Key Lock Set
Item
Photo
Description
1. Follow 2.1.6 item 1 to 3 remove
1
EMI chassis
1. Remove 2 screws
2
2. Remove cover bracket
3
1. Remove 2 antennas
2. Remove tape
4
1. Remove 4 screws
3/20/2007
15/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
5
1. Separate front cover from back cover
6
1. Remove 4 screws from hinge
7
1.
2.
Set upper case vertically
Remove back hinge cover
2
1
8
1. Set upper case horizontally
2. Remove front hinge cover
1
2
3/20/2007
16/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
9
1. Remove 3 screws at left hinge
2. Remove 3 screws at right hinge
10
1. Separate upper case from bottom
case
2. Pull out cables from upper case
11
1.Remove and replace with another key
lock set (W/ LCD Hinge Assembly /
LCD Base)
3/20/2007
17/84
Rev. 1.1
EBN Technology Corp.
2.2
Base Unit
2.2.1 Base Housing
Item
Photo
Description
1
1. Remove 4 screws from hinge front
side
2
1. Set upper case vertically
2. Remove back hinge cover
3
1. Set top upper case horizontally
2. Remove front hinge cover
1
2
4
3/20/2007
1. Remove 3 screws at left hinge
2. Remove 3 screws at right hinge
18/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
5
1. Separate upper case from bottom case
2. Pull out cables from upper case
6
1. Turn the bottom case to the bottom
side
2. Remove 2 screws to take off the kit
cover
7
1. Turn the bottom case top side
2. Take off kit cover
8
1. Turn the bottom case to the bottom
side
2. Remove 4 screws
3. Remove 4 Plastic foot
3/20/2007
19/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
9
1. Turn to the rear side of the bottom
case
2. Remove 2 screws to open the HDD
cover
10
3/20/2007
1. Remove and replace with another
base housing from base chassis
20/84
Rev. 1.1
EBN Technology Corp.
2.2.2 Swivel Housing Rear / Front
Photo
Item
Description
1
1. Remove 4 screws from hinge
2
1.
2.
Set upper case vertically
Remove back hinge cover
2
1
1.
2.
3
1
Set upper case horizontally
Remove front hinge cover
2
3/20/2007
21/84
Rev. 1.1
EBN Technology Corp.
2.2.3 P/S 220W W/PFC
Photo
Item
Description
1. Follow 2.2.1 item 1 to 10
1
(Remove base housing)
2
2. Remove power cable
3
3. Remove HDD to M/B cable
4. Pull out HDD tray
2
1. Turn to bottom side and remove 6
screws
3
1. Turn to top side
2. HDD cable is tied with another
black magic sticker separately
4
1. Remove black magic sticker used
for HDD cable
2. Remove HDD cable
2
1
3/20/2007
22/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
5
1. Separate swivel hinge from base
chassis
6
2
1
7
1. Remove black magic sticker used
for tightening cables
2. Pull out cables from swivel hinge
one by one
1. Remove power cable which
connects PSU and I/O Board
2. Remove 2 tapes
1
2
2
8
3/20/2007
1. Remove black connector together
with cables from power supply
23/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
9
1. Pay attention to the position for
cable
10
1. Remove 3 screws
11
1. Pull up from the hooker and pull to
left direction to remove power
supply
2. Replace with another power
supply
3/20/2007
24/84
Rev. 1.1
EBN Technology Corp.
2.2.4 I/O Board
Photo
Item
Description
1
1. Follow 2.2.3 item 1 to 6
2. Remove USB Cable
5
3. Remove Power supply to I/O
3
2
board cable
4. Remove 100pin cable
5. Remove power supply to AC input
4
cable
2
1. For USB cable, need to remove 1
screw from I/O board
3
1. Turn to bottom side
2. Remove 2 screws
4
1. Remove power supply module from
base chassis
3/20/2007
25/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
5
1. Remove 12 screws
6
1. Remove 4 screws on I/O board
2. Remove and replace with another
I/O board
3. Follow steps back to item 1 for
assembly
2.2.5 HDD / HDD Tray (Refer to 2.5.2)
3/20/2007
26/84
Rev. 1.1
EBN Technology Corp.
2.2.6 Jumper Cover
Item
Photo
Description
1
1. Turn the bottom case to the bottom
side
2. Remove 1 screw
3. Remove and replace with another
jumper cover
3/20/2007
27/84
Rev. 1.1
EBN Technology Corp.
2.3
Boards
2.3.1 Main Board
Photo
Item
Description
1
1. Use screw driver to open upper case.
2. Remove 2 screws
1. Remove 2 screws
2. Remove cover bracket
2
3
5
4
7
8
3
2
1
6
9
3/20/2007
28/84
1. Remove Cables, M/B To Inverter
2. Remove Cables, M/B To Touch
Control Board
3. Remove Cables, M/B To Speaker
4. Remove Cables, M/B To I/O BD
100P
5. Remove Cables, M/B To HDD 80P
6. Remove Cables, 2nd VGA 10P
7. Remove Cables, M/B To I/O BD
20P USB
8. Remove Cable, M/B To Power
Supply
9. Remove Mini PCI
Rev. 1.1
EBN Technology Corp.
Item
4
Photo
Description
1
1. Remove Inverter Cable on top
2. Remove Inverter Cable bottom
2
5
1. Remove 2 screws on bridge board
6
1. Remove bridge board
7
1. Remove 6 screws on M/B
2. Remove 2 銅柱
3/20/2007
29/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
8
1. Remove and replace with another
M/B
2.3.2 Bridge Board
Item
Photo
Description
1
1. Follow 2.3.1 item 1
2. Open upper case
3. Remove VGA cable from bridge
board
4. Remove 2 screws on bridge board
2
1. Remove and replace another bridge
board
3/20/2007
30/84
Rev. 1.1
EBN Technology Corp.
2.3.3 Inverter
Item
Photo
Description
1
1. Follow 2.3.1 item 1
2. Remove 3 cables
3. Remove 2 screws
1. Remove and replace with another
inverter board
2
3/20/2007
31/84
Rev. 1.1
EBN Technology Corp.
2.3.4 Touch Control Board
Item
Photo
Description
1
1.
Follow 2.3.3 item 1 to 2 remove
inverter board
2.
Remove cable from touch control
board
3.
Remove 4 screws
2
1. Push out black clicker from
connector CN2
3
1. Remove touch control board
2. Pull out touch panel cable
3. Replace with anther touch control
board
3/20/2007
32/84
Rev. 1.1
EBN Technology Corp.
2.3.5 Button Board (For POS 75)
Item
Photo
Description
1
1. Follow 2.3.1 item 1
2. Open upper case
2
1. Remove cable from button board
2. Remove 2 screws
3
1. Remove and replace with another
button board
3/20/2007
33/84
Rev. 1.1
EBN Technology Corp.
2.4
Cables
2.4.1 Cable, M/B To Inverter
Item
Photo
Description
1
Part Number: 21600003RH
2
1. Use screw driver to open upper
case.
2. Remove 2 screws
3
1.
2.
3.
2
Remove cable on MB location
CN17
Remove cable on inverter board
Replace with another inverter cable
1
3/20/2007
34/84
Rev. 1.1
EBN Technology Corp.
2.4.2 Cable, M/B To Touch Control BD
Item
Photo
Description
1
1.
Part Number: 21600004RH
2
1.
Use screw driver to open upper
case.
Remove 2 screws
2.
3
1. Remove 3 cables
2. Remove 2 screws
4
1. Remove inverter board
3/20/2007
35/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
5
1.
Remove and replace with another
Touch Control board cable (Main
Board Location CN 17)
2.
Follow steps back to item 1 for
assembly
3/20/2007
36/84
Rev. 1.1
EBN Technology Corp.
2.4.3 Cable, M/B To Speaker
Item
Photo
Description
1
Part Number: 21600006RH
2
1.
Follow 2.1.1 item 1 to 7 turn to
Front side and remove front bezel
3
1.
2.
Turn to back side and remove cable
on MB location CN 14
Remove black tape
1.
2.
3.
4.
Remove 2 screws on left speaker
Remove 2 screws on right speaker
Replace with another speaker cable
Follow steps back to item 1
1
2
4
2
1
3/20/2007
37/84
Rev. 1.1
EBN Technology Corp.
2.4.4 Cable, M/B To I/O BD 100P
Item
Photo
Description
1
1.
Part Number: 21600007RH
2
1.
Follow 2.1.7 item 1 to 9 to
disassemble upper case
Follow 2.2.1 item 1 to 10 to
disassemble base unit
Follow 2.2.3 item 1 to 7 to remove
tapes and power supply cable
Remove black magic sticker
Pull out cables from swivel hinge
one by one
2.
3.
4.
5.
1.
3
2.
3/20/2007
38/84
Remove and replace cable on IO
Board Location CN2
Follow steps back to item 1 for
assembly
Rev. 1.1
EBN Technology Corp.
2.4.5 Cable, M/B To HDD 80P
Item
Photo
Description
1
Part Number: 21600008RH
2
1.
2.
3.
Follow 2.2.1 item 1 to 10 to
disassemble base unit
Remove and replace with another
HDD cable
Follow steps back to item 1 for
assembly
2.4.6 Cable, 2nd VGA to I/O Board
Item
Photo
Description
1
Part Number: 21600009RH
Location on M/B CN5
2
1.
2.
3.
4.
5.
3/20/2007
39/84
Follow 2.1.7 item 1 to 9 to
disassemble upper case
Follow 2.2.1 item 1 to 10 to
disassemble base unit
Follow 2.2.3 item 1 to 7
Remove black magic sticker
Pull out cables from swivel hinge
one by one
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
3
1.
Remove 2 screws from front side to
2.
disassemble VGA connector
Remove power cable from IO
3.
board
Remove power cable
1
2
3
4
1. Remove black tape
5
1.
2.
Remove black tape
Remove fan cable
1.
2.
Remove screw from USB cable
Remove USB cable connector in
order to take off AC Inlet To P/S
cable
Replace with another AC Inlet To
P/S cable
Follow steps back to item 1 for
assembly
2
6
3.
4.
3/20/2007
40/84
Rev. 1.1
EBN Technology Corp.
2.4.7 Cable, M/B To I/O BD 20P USB
Item
Photo
Description
1
Part Number: 21600016
MB Location CN11
1.
2
2.
3.
4.
5.
3
1.
2.
3.
2.4.8
Item
disassemble upper case
Follow 2.2.1 item 1 to 10 to
disassemble base unit
Follow 2.2.3 item 1 to 7
Remove black magic sticker
Pull out cables from swivel hinge
one by one
Remove screw from IO Board
Remove and replace another USB
cable
Follow steps back to item 1 for
assembly
Cable, M/B To Button Board
Photo
Description
1
3/20/2007
Follow 2.1.7 item 1 to 9 to
1.
2.
3.
41/84
Follow 2.3.1 item 1
Open upper case
Remove and Replace with another
M/B to Button board cable
Rev. 1.1
EBN Technology Corp.
2.4.9
Item
Cable, LCD to Bridge Board
Photo
Description
1
1 Part No.:21600005RH
2
1. Follow 2.1.2 item 1 to item 3
remove touch panel
2. Turn to back side
3. Remove 4 screws
3
1. Cut plastic string
1
4
1. Remove 2 inverter cables
2. Remove LCD cable from bridge
board
2
1
3/20/2007
42/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
5
1. Remove LCD chassis
6
1. Remove tape
2. Remove and replace with another
LCD cable
3. Follow steps back to item 1 for
assembly
2
1
3/20/2007
43/84
Rev. 1.1
EBN Technology Corp.
2.5
Item
Main & Base Unit assembly
Photo
Description
1
1. Prepare upper and base unit
2
1. Put upper unit on the swivel hinge
1. Fasten 3 screws on the left side
of neck
2. Fasten 3 screws on the right
side of neck
3
4
3/20/2007
1. Put cables through upper case hole
44/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
5
1. Cables must go through the
hole at center of upper case
2. Connect cables to the MB
6
1. Tied cables with magic tape
2. Fasten cover bracket with 2
screws
7
1. Fasten EMI cover on the upper case
with 7 screws
8
1. Put on the front cover W/O fastening
screws.
3/20/2007
45/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
9
1. Put swivel hinge back cover on case
10
1. Fasten 4 screws
3/20/2007
46/84
Rev. 1.1
EBN Technology Corp.
2.6
Accessories
2.6.1 HDD
Photo
Item
Description
1
1. Follow 2.2.1 item 1 to 10 (Remove
base housing)
2. Remove power cable
3. Remove HDD to M/B cable
4. Pull out HDD tray
2
3
2
1. Remove 2 screws from HDD left
hand side
2. Remove 2 screws from HDD right
hand side
3
1. Remove and replace with another
HDD
3/20/2007
47/84
Rev. 1.1
EBN Technology Corp.
2.6.2 Pole Display
Item
Photo
Description
1
1. Packing List:
a. Assembly(1 )Tube and(2 )VFD
Unit
H/W Installation
1
1. Remove the customer display cover
from rear base
2
1. Remove two screws marked in red
3
1. Install the VFD kit on rear base
3/20/2007
48/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
4
1. Connect VFD cable to COM1 and
screw up
5
1. Remove jumper cover, adjust Pin9
13-14 close for COM1 to be 12V
Verification
6
Verify the VFD through by Hyper
Terminal as following procedure.
Enter to “All Programs” “Communication” “Hyper Terminal”
7
1. Click “Yes” to continue
3/20/2007
49/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
8
1. Set “area code” and click OK
9
1. Select on using COM1 port.
10
1. Set on Baud Rate to be 9600 bps.
11
1. Press random character from
keyboard which will be shown on VFD
3/20/2007
50/84
Rev. 1.1
EBN Technology Corp.
2.6.3 MSR
Item
Photo
Description
1
1. 3 tracks MSR module (PS2)
H/W Installation
1
1. Screw off the cover.
2
1. Pass through the MSR cable under
the Inverter BD, connect to CN12 of
M/B
3
1. Screw up the module to the slot.
3/20/2007
51/84
Rev. 1.1
EBN Technology Corp.
Verification
1
1. Enter to “Accessories” “Notepad”
2
1. Stripe the MSR card to Reader and
complete test OK.
3/20/2007
52/84
Rev. 1.1
EBN Technology Corp.
2.6.4 MSR+ I Button
Item
Photo
Description
1
1. 3 tracks MSR module (PS2)
H/W Installation
1
1. Screw off the cover.
2
1. Pass through the MSR cable under
the Inverter BD, connect to CN12 of
M/B
3
1. Screw up the MSR to slot.
3/20/2007
53/84
Rev. 1.1
EBN Technology Corp.
Verification
1
1. Enter to “Accessories” “Notepad”
2
Complete test OK.
I-Button
Data
Card Reader
Data
3/20/2007
54/84
Rev. 1.1
EBN Technology Corp.
2.6.5 MSR+ Smart Card
Photo
Item
Description
1
1. MSR 3 tracks (Serial Port) + Smart
Card Reader module (USB)
H/W Installation
1
1. Screw off the cover.
2
1. Pass through the cables under the
Inverter BD, connect to COM cable to
CN12 as red mark 1. Connect Smart
cable to JP6 as red mark2.
3
1. Screw up the module to the slot
3/20/2007
55/84
Rev. 1.1
EBN Technology Corp.
Verification MSR
1. 1. Enter to” All Programs” 1
“Communication” “Hyper
Terminal”
2. b. Set the configuration as same to
VFD as above
2
1. Set on using COM5 port.
3
1. Set on Baud Rate to be 9600 bps.
4
1. Stripe the MSR card to Reader and
complete test OK
3/20/2007
56/84
Rev. 1.1
EBN Technology Corp.
Smart Card Driver Installation and
Verification
1
1. Select “Yes, this time only” and
Click Next
2
1. Install the software automatically
[Recommended] and Click Next
3
1. Click Finish for complete
installation
4
1. Enter to Smart Card Utility Select “SYN_PcSc_Test”
3/20/2007
57/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
5
1. Select STD 200 0
6
1. Insert IC Card to slot
7
1. Show “PASS” complete test OK
3/20/2007
58/84
Rev. 1.1
EBN Technology Corp.
2.6.6 2nd Display W/ Touch
Item
Photo
Description
1. 12.1 / 15” display with Fujitsu
1
Touch Panel
2. Cable 1: VGA with power pin
I/P.
Cable 2: Serial touch with power
pin I/P.
H/W Installation
1
1. Screw off the two screws as red
mark.
2
1. Install the second display unit
with POS70
3/20/2007
59/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
3
1. Fasten the 2nd display with 6
screws as red mark. Connect
cable 1 to VGA port and cable 2
to COM1
4
1. Remove the jumper cover, adjust
Pin1 21-22 close for COM1 to be
5V
Driver Installation and Verification
1
Driver Installation and Verification
1. Display Setup
2. Enter to “Control Panel”
2
1. Click “Display” icon
3/20/2007
60/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
3
1. Set main display by “Settings” to
2.[Multiple Monitors ]…
4
1. Select “Extend my Windows
Desktop onto this monitor on
VIA/S3G.
5
1. Click “Yes” for save the settings.
The 2nd display was shown out
the extend the screen
Install Touch Driver
1
3/20/2007
1. Insert the Driver Bank disc to
CD ROMSelect “POS7
Series”
61/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
2
1. Select “Touch Driver”
3
1. Select “FUJITSU TOUCH
PANEL”
4
1. Select “Fujitsu Touch Panel
Driver (SERIAL Interface)”
5
1. Select “Non Plug and Play
Device” and click OK
3/20/2007
62/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
6
1. Click OK for completed
installation
7
1. Select dual port for touch by
COM1 and COM6
8
1. Completed installation Click
“Yes” for restart system
9
1. Enter to “Control Panel”
3/20/2007
63/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
10
1. Click “Touch Panel” icon
11
1. Select Dual monitor set-up
12
1. Select “Calibration” Connected port COM1 & COM6
3/20/2007
64/84
Rev. 1.1
EBN Technology Corp.
2.6.7 RFID
Item
Photo
Description
1
1. RFID module (Serial I/F)
H/W Installation
1
1. Screw off the cover.
2
1. Pass through the RFID cable under
the Inverter BD, connect to CN12 of
M/B
3
1. Screw up the RFID on the slot.
3/20/2007
65/84
Rev. 1.1
EBN Technology Corp.
Verification
1
1.
Enter to” All Programs” “Communication” “Hyper Terminal”
2.
Set the configuration as same VFD
as above
2
1. Set on using COM5 port.
3
1. Set on Baud Rate to be 9600 bps.
4
1. Attach the RFID card to Reader,
completed test OK
3/20/2007
66/84
Rev. 1.1
EBN Technology Corp.
2.6.8 Compact Flash
Item
Photo
Description
1
1. Compact Flash
2
1. Use screw driver to open upper case
2. Remove 2 screws
3
1. Remove 2 screws on bridge board
4
1. Take off plastic strings from the
hook
2. Remove bottom cable
3/20/2007
67/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
5
3/20/2007
1. Put compact flash on socket
68/84
Rev. 1.1
EBN Technology Corp.
2.6.9 Smart Card
Photo
Item
Description
1. MSR 3 tracks (Serial Port) + Smart
1
Card Reader module (USB)
H/W Installation
1
1. Screw off the cover.
2
1. Pass through the cables under the
Inverter BD. Connect Smart cable to
JP6 as red mark
3
1. Screw up the module to the slot
3/20/2007
69/84
Rev. 1.1
EBN Technology Corp.
Smart Card Driver Installation and
Verification
3. Select “Yes, this time only” and
1
Click Next
2
4. Install the software automatically
[Recommended] and Click Next
3
5. Click Finish for complete
installation
4
6. Enter to Smart Card Utility Select “SYN_PcSc_Test”
3/20/2007
70/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
5
7. Select STD 200 0
6
8. Insert IC Card to slot
7
9. Show “PASS” complete test OK
2.6.10
Item
I Button
Photo
Description
1
3/20/2007
1. PS2-I button module kit
71/84
Rev. 1.1
EBN Technology Corp.
H/W Installation
1
1. Screw off the cover.
2
1. Pass through the I-button under the
Inverter BD, connect to CN12 of M/B
3
1. Screw up the MSR to slot.
Verification
1. Enter to “Accessories” “Notepad”
1
3/20/2007
72/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
2
Complete test OK.
I-Button
Data
2.6.11
Item
Mini PCI Wireless LAN
Photo
Description
1
Mini PCI Wireless LAN
2
1. Use screw driver to open upper case
2. Remove 2 screws
3
1. Insert the WLAN card to mini PCI
slot
2. Connect the Antenna to card as red
mark
3/20/2007
73/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
4
1. Press Wireless LAN Card
2. Make sure connected well
5
1. Remove 2 screws from cover
bracket
2. Remove cover bracket
3. Antenna cable needs to go under
cover bracket
4. Remove EMI cover
6
1. Tied Antenna cable with other
cables
7
1. Stick the Antenna by temped tape to
back cover
3/20/2007
74/84
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
8
3/20/2007
1. Tighten 7 screws on EMI cover.
75/84
Rev. 1.1
EBN Technology Corp.
3
Chapter 3 : Spare parts list
3.1 Main Unit
3.1.1 Explode of Main Unit
3.1.2 Main Unit Parts list & quotation
Item
1+2
1+2
3+5
3+5
4
3/20/2007
Parts No.
10500004RH
10500025RH
A10400288RH
A10400582RH
10500003RH
Description
Q’ty
15.0" Bezel PC+ABS 1CAV
1
@Rubber Black +T4000, 310*2.4*1.5T
2
@Rubber Black +T4000, 238*2.4*1.5T
2
12.1" Bezel PC+ABS 1CAV
1
@ Rubber Black +T4000, 252*1.8*1T
2
@ Rubber Black +T4000, 195*1.8*1T
2
Fujitsu 15.0"touch panel
N010-0510-T237
Touch Screen Holder- 15.0"
Call Sales
Call Sales
1
1
@SPONG FOR POS70-15.0 312*5*1
2
@SPONG FOR POS70-15.0 245*5*1
2
Fujitsu 12.1"touch panel
1
Touch Screen Holder-12.1” w/ Sponge
1
Square Speaker(Left and Right)
1
Speaker Cable
1
76/84
Price (US$)
Call Sales
Call Sales
Call Sales
Rev. 1.1
EBN Technology Corp.
Item
Parts No.
Description
Q’ty
Price (US$)
6
21100014RH
LCD, AUO 15” 1024 x 768, 350nits
1
Call Sales
6
21100001RH
LCD, LG 12’1, 800*600, 300nits
1
Call Sales
7
30100017RH
LCD Chassis-15.0(AUO)
1
Call Sales
7
30100010RH
LCD Chassis-12.0 (LG)
1
Call Sales
8
30200007RH
LED Lens, transparent
1
Call Sales
9
10100001RH
Main Board, EBN-370-RH
1
Call Sales
10
10100004RH
FUJITSU Touch Panel Control
Board:N16B-0558-B280
1
Call Sales
11
10100007RH
1
Call Sales
11
10100006RH
Bridge Board-LVDS, 24Bit (15”, AUO
LCD)
1
Call Sales
12
22400012RH
Inverter: 12.1/15.0", 8mA, RI1205-06G
1
Call Sales
13
30200015RH
LCD BASE Cover, ABS, Black
1
Call Sales
14
30100003RH
Cable Cover Bracket , 0.3T
1
Call Sales
15
30100120RH
EMI Chassis
1
Call Sales
LCD Hinge Assembly
1
Key Pad
1
15” LCD Base
1
LCD Hinge Assembly
1
Key Pad
1
12.1” LCD Base
1
16+17+1
8
16+17+1
8
3/20/2007
10500005RH
10500006RH
Bridge Board-TTL, 18Bit+TTL (12.1”,
LG LCD)
77/84
Call Sales
Call Sales
Rev. 1.1
EBN Technology Corp.
3.2
3/20/2007
Base Unit
3.2.1 Explode of Base Unit
78/84
Rev. 1.1
EBN Technology Corp.
3.2.2 Base Unit Parts list & quotation
Item
Parts No.
Description
Q’ty
Price (US$)
1
10500002RH
Swivel Front Cover, Black Sub-ASSY
1
Call Sales
2
30200009RH
KIT Cover
1
Call Sales
3
10500001RH
Swivel Rear Cover, Black Sub-ASSY
1
Call Sales
4
30200003RH
Base Housing,PC+ABS,Black
1
Call Sales
5
30200013RH
HDD Cover
1
Call Sales
7
30100006RH
HDD Tray
1
Call Sales
8
10200004RH
15”/12.1” Swivel Hinge Assembly
1
Call Sales
9+10+
11
A10400216RH
Power Supply Module:
1
1U, 220W, W/PFC
Call Sales
12
10100002RH
I/O Board
1
Call Sales
13
30100002RH
Base Chassis
1
Call Sales
14
30500024RH
Plastic Foot
4
Call Sales
15
30200016RH
Jumper Cover
1
Call Sales
3.3
Cables
Part No.
Description
Photos
Price
21600003RH
Cable, M/B To Inverter
Call Sales
21600004RH
Cable, M/B To Touch Control
Board
Call Sales
21600006RH
Cable, M/B To Speaker
Call Sales
3/20/2007
79/84
Rev. 1.1
EBN Technology Corp.
Part No.
Description
Photos
Price (US$)
21600007RH
Cable, M/B To I/O BD 100P
Call Sales
21600008RH
Cable, M/B To HDD 80P
Call Sales
21600009RH
Cable, 2nd VGA to I/O board
10 pin transfer to D-SUB 15
pins
Call Sales
21600016RH
Cable, M/B To I/O BD 20P
USB
Call Sales
21600088RH
POS-70 IDE Y CABLE
Call Sales
21600089RH
POS-70 HDD POWER Y
CABLE
Call Sales
3/20/2007
80/84
Rev. 1.1
EBN Technology Corp.
Part No.
21600002RH
3.4
Description
Photos
Cable for 24V Printer
Price (US$)
Call Sales
Accessories
3.4.1 Power Cord
Part No.
Description
Photos
Price (US$)
POWER CORE FOR USA
Call Sales
POWER CORD FOR UK
Call Sales
POWER CORD FOR EUR
Call Sales
POWER
Australia
Call Sales
20700001RH
20700005RH
20700002RH
CORD
FOR
20700004RH
3.4.2 HDD
Part No.
Description
Photos
Price (US$)
20200009RH
SEAGATE
5400RPM-40G
HDD
ULTRA
ATA/100
ST340015A
Call Sales
20200006RH
80G HDD WD 7200RPM
Call Sales
3.4.3 Pole Display
Part No.
3/20/2007
Description
Photos
81/84
Price (US$)
Rev. 1.1
EBN Technology Corp.
A10400265RH
VFD Type
Call Sales
A10400264RH
LCD Type
Call Sales
3.4.4 MSR
Part No.
Description
Photos
Price (US$)
A10400010RH
2 Track : PS2
Call Sales
A10400023RH
2 Track : RS232
Call Sales
A10400009RH
3 Track : PS2
Call Sales
A10400024RH
3 Track : RS232
Call Sales
3.4.5 2nd Display
Part No.
Description
Photos
Price (US$)
A10400022RH
12” TFT LCD(w/o Touch)
Call Sales
A10400004RH
15” TFT LCD(w/o Touch)
Call Sales
A10400062RH
12” TFT LCD(w/ Touch)
NA
Call Sales
A10400107RH
15” TFT LCD(w/ Touch)
NA
Call Sales
3/20/2007
82/84
Rev. 1.1
EBN Technology Corp.
3.4.6 OS
Part No.
Description
Price (US$)
20900003RH
Win2000 Professional Edition
Call Sales
20900001RH
WinXP Professional Edition
Call Sales
20900008RH
Microsoft XP Home SP2, Chinese Ver.
Call Sales
20900002RH
WEPOS, English Ver.
Call Sales
3.4.7 RFID
Part No.
A10400005RH
Description
Photos
RFID
Price (US$)
Call Sales
3.4.8 Compact Flash
Part No.
Description
Photos
Price (US$)
20600001RH
Compact Flash 128MB
Call Sales
20600002RH
Compact Flash 256MB
Call Sales
20600003RH
Compact Flash 512MB
Call Sales
20600005RH
Compact Flash 1G
Call Sales
3.4.9 Memory
Part No.
Description
Price (US$)
20300001RH
Memory: 128MB
Call Sales
20300002RH
Memory: 256MB
Call Sales
20300003RH
Memory: 512MB
Call Sales
20300004RH
Memory: 1G
Call Sales
3.4.10
Part No.
A10400104RH
3/20/2007
Smart Card +MSR 3T RS232
Description
Photos
Smart Card +MSR 3T RS232
83/84
Price (US$)
Call Sales
Rev. 1.1
EBN Technology Corp.
3.4.11
Part No.
A10400121RH
3.4.12
I Button +MSR 2T KB
Description
Photos
I Button +MSR 2T KB
Price (US$)
Call Sales
Wireless LAN
Part No.
Description
30400001RH
ANTENNA 35B/L+R
Call Sales
10100029RH
WIRELESS LAN 11g MINI
PCI MODULE
Call Sales
3/20/2007
Photos
84/84
Price (US$)
Rev. 1.1
Download PDF