QUADSCAN
User’s Guide
Door Mounted Presence sensor
1
DESCRIPTION
1
2
3
4
5
6
1. housing
2. clip
3. main connector
4. DIP-switch
5. range adjustment screw
6. receiver
7. end cap
8. clip with angle adjustment screw
9. emitter
10. push/setup button
11. lens cover
NOTE: BEA refers to the emitter/ receiver sensing unit within the housing as a module.
2
TECHNICAL SPECIFICATIONS
Technology:
Detection field:
Mounting height:
Range Adjustment
Reaction time:
Supply voltage:
Max current consumption:
Output:
Max. contact voltage
Max. contact current
Max. switching power
Input:
Max. contact voltage:
Voltage threshold:
Max. number of modules:
Reflectivity:
Degree of protection:
Temperature range:
Norm conformity:
Active infrared with background suppression
15 3/4 in. (W) x 2 3/4 in. (D) (at 6 1/2 ft. mounting height; 4 spots active)
400 mm (W) x 70 mm (D) (at 2 m mounting height; 4 spots active)
3 ft. 7 in. (1.1 m) to 9 ft. 10 in. (3 m) mechanical range adjustment screw
64 ms (typ)
12 V - 24 V AC +/-10% ; 12 V - 30 V DC -5%/+10%
65 mA @ 24 V AC/ 75 mA @ 24 V DC (EACH MODULE)
2 relays (free of potential contact)
42 V AC/DC
1 A (resistive)
30 W (DC) / 60 VA (AC)
1 optocoupler (free of potential contact)
30 V high: >10 V DC low: <1 V DC
4 (up to 6 if 24 V DC) min 5% at IR-wavelength of 850 nm
IP53
-13°F to + 131°F (-25°C to +55°C); 0-95% relative humidity, non condensing
EMC 2004/108/EC; MD 2006/42/EC
EN ISO 13849-1:2008 Performance Level «c» CAT 2; EN 12978
Specifications are subject to changes without prior notice.
Other use of this device outside it’s permitted purpose cannot be guaranteed by the manufacturer.
7
8
9
10
11
Page 1 of 5 75.5381.02 20111101
4
3
!
PRECAUTIONS
CAUTION
Shut off all power before attempting any wiring procedures.
Maintain a clean & safe environment when working in public areas.
Constantly be aware of pedestrian traffic around the door area.
Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.
ESD electrostatic discharge: Circuit boards are vulnerable to damage by electrostatic discharge.
Before handling any board ensure you dissipate your body’s charge.
Always check placement of all wiring before powering up to insure that moving door parts will not catch any wires and cause damage to equipment.
Ensure compliance with all applicable safety standards (i.e. ANSI A156.10 / 27 / 19) upon completion of the installation.
DO NOT attempt any internal repair of the sensor. All repairs and/or component replacements must be performed by BEA, Inc. Unauthorized disassembly or repair:
1. May jeopardize personal safety and may expose one to the risk of electrical shock.
2. May adversely affect the safe and reliable performance of the product and will result in a voided product warranty.
MOUNTING THE HOUSING
3/4 in.
(2 cm)
Take into account the position of the white clips before drilling and fastening
the screws.
Mount the housing as close as possible to the leading edge. Leave 3/4 inch
(2cm) for installation of the black end caps.
If installing the housing on each side of the door carefully locate and drill a
wire passage hole thru the housing, door and opposing housing.
5
PREPARING THE WIRING
Pass the cable through the flexible wire sheath and snap off only one of the precut part of the end cap.
Caution, end caps are handed.
1/8”(3mm)
CL
7/8”
(22mm)
CL Drill 3 holes in the fixed part of the door frame. Pass the cable through the hole in the middle and fasten the flexible wire sheath using the two screws.
Pre-cut snap out for flexible wire sheath.
(Wire sheath not shown)
1/2”(12mm) for wire passage
6
ORIENTATION AND POSITION OF THE MODULE(S)
The angle adjustment clip should be next to the emitter.
Clip right door edge left door edge
Page 2 of 5
Turn the module
if necessary.
TX
Orient the dip switches towards the center of the door
If necessary, to move the module(s) left or right:
1. Remove from housing
2. Re-position within housing
3. Re-set into housing
If necessary, when a module needs to be turned:
1. detach the clips
2. turn them by 180°
3. reattach
75.5381.02 20111101
7
8
INSTALLING THE WIRING HARNESS
P/N: 20.5259.03
Control end
Slave cable connects between any module.
Module with the power cable connected to the door control becomes the master module.
WIRING AND RELAY CONFIGURATION
WIRE COLOR
RED
BLACK
WHITE
GREEN
YELLOW
DESIGNATION
POWER
POWER
COM.
N.O.
N.C.
WHITE/BLACK COM.
GREEN/BLACK N.O.
YELLOW/BLACK N.C.
BLUE
BROWN
MONITOR/TEST (+)
MONITOR/TEST (-)
FUNCTION
INPUT
12 - 24 VAC/DC
RELAY 1 (S) OUTPUT
SAFETY SIDE RED LED
Quadscan end
Ensure to properly connect the correct plug connector into its respective location. If a plug option doesn’t exist at your control, simply cut off the plug and hardwire at the control end.
CONNECTIONS
POWER SOURCE
RELAY 2 (A) OUTPUT
APPROACH SIDE GREEN
LED
CONNECT TO ACTIVATION
INPUT OF DOOR CONTROL
CONNECT TO SAFETY/STALL
INPUT OF DOOR CONTROL
EXTERNAL MONITORING CONNECT TO MONITORING INPUT
OF DOOR CONTROL
Plug the SLAVE CABLE between the modules in one of the two plug in connectors.
The module connected to the door controller becomes the MASTER.
9
SETTINGS
ON
DOOR
SIDE
RELAY 1 (S)
SAFETY SIDE
FREQ 1 (F1) ON
UNCOVERED
ZONE
H
OFF
RELAY 2 (A)
APPROACH SIDE
FREQ 2 (F2) OFF L
FACTORY
VALUE
Dip Switch 1 2 3 4
LED during detection
R1 = RED
R2 = GREEN
Set different frequencies on modules close to each other.
For low reflective floors it is recommended to turn off Background.
Factory defaulted to detect a 28 inch minimum high person.
Notes:
Dip Switch 2: Frequency 1 or 2 is not specific for the safety or approach side. 2 modules within the same housing must be set to different frequencies.
Dip Switch 3:
In rare occasions with low background reflectivitey it may be desirable to change dip switch 3.
Dip Switch 4:
In most cased it’s not necessary to change dip switch 4. When mounting above 8ft it may be desirable to change dip switch 4.
Page 3 of 5
X
ORANGE GREEN OFF
After changing a DIP-switch, the orange LED flashes.
Next Perform a LONG (approx. 3 sec.) push on the MASTER push button as this confirms the settings of ALL
MODULES.
Afterwards, a number of green flashes (x) indicates the number of connected modules.
Note: A long push on a slave module will only confirm its settings.
75.5381.02 20111101
10
SETUP (MANUAL SETUP RECOMMENDED)
During any set up (via the flashing red/green LED), ensure to remove all object within the detectin zone and do not stand in the field during set up!
Step 1: A SHORT push on the button of the MASTER launches a setup on ALL MODULES OF THE GIVEN DOOR.
RED-
GREEN
OFF
Step 2: If setup is not successfull; based on each module(s) LED flashing
rate and color, follow step 3 after reading the important
note to the right.
Step 3: Next to the dip switches; slowly turn the adjustment screw
clockwise to increase the range.
RED Next to the dip switches; slowly turn the screw counterclockwise to decrease the range .
ORANGE
4
ORANGE
Step out of the detection field.
If necessary, change angle or see troubleshooting section 13.
Launch a new setup. See troubleshooting section 13.
5
11
MODULE ANGLE ADjUSTMENTS
Test if door and sensor function correctly. Ensure the swing side will slow/stop the door and the approach side will activate/re-activate the door.
If necessary, use spotfinder to adjust IR spots closer to or away from the door face and relaunch a setup as described in step 10.
Walk test to ensure compliance to ANSI 156.10.
12
INSTALLING THE LENS COVER
After adjustment, you can fasten the lens and end caps. To fasten the lens correctly, position the curved side at the bottom and snap the top into place. Install the end caps (shown on page 2) using the supplied screws.
Note:
Slowly turning the adjustment screw increases the flashing speed of the LED when approaching the optimal position. Once at the optimal position, the sensor will automatically launch a new setup via the flashing red/green LED.
13
TROUBLESHOOTING (LED SIGNALS)
LED Probable Cause
The RED or GREEN
LED is ON sporadicly.
The RED or GREEN LED is
ON permanently.
Incorrect adjustment
Incorrect adjustment of the uncovered zone.
The sensor signals an internal fault.
The ORANGE LED is on permanently.
The ORANGE LED flashes quickly.
The ORANGE LED flashes 1 x every 3 seconds.
1
2
Page 4 of 5
The ORANGE LED flashes
2 x every 3 seconds.
DIP-switch setting awaiting confirmation.
The sensor signals an internal fault.
Voltage over or under specification.
1
Corrective Action
Launch a new set up.
1 Launch a new setup.
1
1
2
1
2
Replace module(s).
Corfirm the DIP-switch setting: long push on the push button.
Cut and restore power supply.
If orange LED flashes again, replace sensor.
Check power supply.
- Faulty or incorrect power supply.
Replace cable
75.5381.02 20111101
13
TROUBLESHOOTING CONTINUED (LED SIGNALS)
LED Probable Cause
3
The ORANGE LED flashes
3 x every 3 seconds.
Communication error between modules.
4
The ORANGE LED flashes 4 x every 3 seconds.
The sensor does not receive enough
IR-energy.
5
The ORANGE LED flashes
5 x every 3 seconds.
The ORANGE LED flickers.
The sensor receives too much IR-energy.
IR saturation
Set up error
The sensor is disturbed by lighting or another sensor.
14
ACCESSORIES
1
2
3
4
1
2
1
Corrective Action
Check wiring between modules.
Launch a module count: long push on push button of MASTER module.
Step out of the detection zone.
Launch a new set up.
Change angle of the module.
Switch off background.
Launch a new set up.
1
2
3
1
Check mounting height.
Adjust range or angle of module.
Cut and restore power.
- Launch a new set up.(If Orange LED flashes again replace module).
Select a different frequecy for each module
(DIP 2).Launch a new set up.
10Spotfinder 1024VAC 10BR3
15
ANSI/AAADM COMPLIANCE
ANSI / AAADM Compliance
A A ADM
American Association of
Automatic Door Manufactures
Upon finishing the installation and/or service work perform at a minimum a daily safety check in accordance with the minimum inspection guidelines provided by AAADM. Provide each owner with an owner’s manual that includes a daily safety checklist and contains at a minimum the information recommended by AAADM. Offer a familiarization session with the owner explaining how to do daily inspections and calling out location of cutoff switches to put equipment out of service if a deficiency is noted. The equipment should be inspected in accordance with the minimum inspection guidelines annually. A safety check that includes at a minimum the items listed on the safety information label must be performed during each service call. If you are not an AAADM certified inspector BEA strongly recommends to have an
AAADM certified inspector perform an AAADM inspection and placing a valid inspection sticker below the safety information label prior to placing the equipment into operation.
16
COMPANY CONTACT
Do not leave problems unresolved. If a satisfactory solution cannot be achieved after troubleshooting a problem, please call BEA, Inc. If you must wait for the following workday to call BEA, leave the door inoperable until satisfactory repairs can be made. Never sacrifice the safe operation of the automatic door or gate for an incomplete solution.
Our Service Technicians can be called 24 hours a day, 7 days a week. For more information visit www.beasensors.com.
Page 5 of 5
Phone: 1-800-523-2462
West / Mexico
1-888-419-2564
After Normal Business Hours
Central
1-800-407-4545
Fax: 1-888-523-2462
AK, MI, WI, TX, Canada
1-866-836-1863
East
1-866-249-7937
75.5381.02 20111101
