POS-7015EG-370

EBN Technology Corp.

U s e r r M a n u a l l

P O S 7 0 S e r r i i e s

*POS70-2EB-370

*POS70-2EB-478

*POS70-5EB-370

*POS70-5EB-478

Mar. 2007

©Copyright 2007 by EBN Technology Corp. All Rights Reserved.

2007/8/21 1/47 Version 1.2


Copyright Notice

The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

Trademarks

Intel is a registered trademark of Intel Corporation. AMI is registered trademarks of AMI SOFTWARE INTERNATION, INC. Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

2007/8/21 2/47 Version 1.2


Contents

Chapter 1 – Introduction ............................................................................................ 5

1.1 System Overview .......................................................................................... 5

1.1.1 System Outlook.................................................................................. 5

1.1.2 Rotating Angle .................................................................................... 6

1.1.3 System Maintain................................................................................. 6

1.1.4 I/O Ports................................................................................................ 7

1.2 Specifications ................................................................................................ 8

Chapter 2 – Packing List.......................................................................................... 12

Chapter 3 – Getting Started..................................................................................... 17

3.1 System setup ............................................................................................... 17

3.2 Hardware Installation ................................................................................. 18

3.2.1 CPU Installation................................................................................ 18

3.2.2 Memory Installation......................................................................... 19

3.2.3 HDD Installation ............................................................................... 20

3.2.4 OS Installation .................................................................................. 21

3.3 Software Installation................................................................................... 22

3.3.1 Driver Installation ............................................................................ 22

3.3.2 Touch Panel Calibration................................................................. 24

3.4 Optional Items Installation........................................................................ 26

3.4.1 MSR / RFID......................................................................................... 26

3.4.2 Pole Display ...................................................................................... 30

3.4.3 2 nd

Display ......................................................................................... 31

Chapter 4 – BIOS setup............................................................................................ 33

4.1 P4 M/B ............................................................................................................ 34

4.1.1 Starting Setup ................................................................................... 34

4.1.2 Resolution setup.............................................................................. 35

4.2 P3 M/B ............................................................................................................ 37

4.2.1 Starting Setup ................................................................................... 37

4.2.2 Resolution setup.............................................................................. 38

Chapter 5 – M/B Information................................................................................... 40

5.1 P4 M/B Jumper Setting .............................................................................. 41

5.2 P3 M/B Jumper Setting .............................................................................. 42

5.3 COM & RJ-11 Jumper Settings ................................................................ 44

5.4 Cash Drawer Introduction......................................................................... 44

Chapter 6 – Reversion History ............................................................................... 47

2007/8/21 3/47 Version 1.2


Introduction

2007/8/21 4/47 Version 1.2


Chapter 1 – Introduction

1.1 System Overview

1.1.1 System Outlook

HDD LED

LAN LED z Speakers z Mounting hole for Pole Display or

2 nd

Display z COM RI/5V/12V selection

2007/8/21 5/47 Version 1.2


1.1.2 Rotating Angle

1.1.3 System Maintain

Remove 2 screws for system maintain

2007/8/21 6/47 Version 1.2


1.1.4 I/O Ports

Number

1

2

Description

AC Power Connector

VGA (For EBN 2 nd

3 LAN

display only)

4

6

7

Printer Port (LPT)

Cash Drawer 2

Cash Drawer 1

10 Audio

11 DC 24V (For Receipt Printer Power)

12

13

Power USB (24V)

Power USB (12V)

2007/8/21 7/47 Version 1.2


1.2 Specifications

System

Model SolidPOS 72 SolidPOS 75

Main Board

CPU

Core Logic

System Memory

OS Support

Display

TFT LCD

Brightness

Resolution

Touch Screen

Tilt Angle

Swivel Angle

Storage Device

HDD

Compact Flash

I/O Ports

Serial

P3: Intel Celeron / PIII 1.2GHz

P4: Intel Mobile Celeron 1.2GHz , Celeron 2.0GHz , P4

2.0GHz

P3: VIA CLE 266 (VT8623+VT8235)

P4: Intel 852GM + ICH4

DIMM, DDR266/333, 128MB up to 1GB

Win2000, NT, Win XP, Embedded XP(XPe), WinCE,

WEPOS

12.1”

300 nits

800 x 600

7 Wire Resistive Type

0 ~ 90 Degree

-20 ~20 Degree

15”

250 nits

1024 x 768

1 x EIDE 3.5” Type

1 x Slot Type II, Non-removable

6 x RS-232

COM 1/ 2/ 3/ 4: DB-9, male, (Pin1 W/ DCD or 5V or 12V

Selectable, Pin 9 W/ RI or 5V or 12V Selectable )

COM 5/ 6: Internal for MSR and Touch Panel

2007/8/21 8/47 Version 1.2

Parallel


1 x DB-25, female, supports SPP/EPP/ECP

USB

PS/2 Mouse

4 x USB 2.0

2 x USB2.0

1 x USB2.0 W/ 12V

1 x USB2.0 W/ 24V

1 x 6-pin mini DIN

PS/2 KB

LAN

VGA

Cash Drawer

Audio

1 x 6-pin mini DIN

1 x RJ45, 10/100 Base-T, supports wake on LAN

1 x DB-15, female

2 x RJ11 (Power Pin 12/24V Selectable)

1x Audio Jack Out

AC97 2.0 Compliant, Speaker 2W x 2

1 x Mini PCI Expansion

Others

Power Input 220W ATX with 100 - 240 VAC input @ 50 - 60 Hz / 5A

Color Gray

Compliance FCC / CE / WEEE / RoHS

Weight(Kgs) 12

Dimension(mm) W x D

340 x 275 x 350 x H

Operating Temperature 5 ℃ ~ 40 ℃

12.5

370 x 277 x 405

Storage Temperature -20°C ~ 60°C

Storage Humidity 20% - 85% RH, non-condensing

Main Unit Ordering Information

Optional Accessories Ordering Information

A10400062RH 2 nd

Display 12.1” TFT LCD

A10400107RH 2 nd

Display 15” TFT LCD

A10400264RH

Customer Display: LCD Pole Display, 20 x 2 characters,

RS-232 Type (Gray)

A10400265RH

A10400010RH

A10400009RH

A10400023RH

Customer Display: VFD Pole Display, 20 x 2 characters,

RS-232 Type (Gray)

MSR: 2 Tracks, KB Type

MSR: 3 Tracks, KB Type

MSR: 2 Tracks, RS-232 Type

A10400024RH MSR: 3 Tracks, RS-232 Type

A10400019RH I Button: PS/2 Type

2007/8/21 9/47 Version 1.2


A10400121RH MSR+ I Button: 2 Tracks, KB Type and I Button PS/2 Type

A10400120RH

A10400104RH

A10400005RH

A10400266RH

MSR+ I Button: 3 Tracks, KB Type and I Button PS/2 Type

MSR+ Smart Card: 3 Tracks, RS-232 Type and Smart

Card USB Type

RFID : RS-232 Type

WIRELESS LAN 802.11b/g MINI PCI MODULE W/

Antenna

20900001RH OS: Win XP Professional (English Version)

20900008RH

20900003RH

20900002RH

OS: WinXP Home (English Version)

OS: Win 2000 Professional (English Version)

OS: WEPOS (English Version)

2007/8/21 10/47 Version 1.2


Packing List

2007/8/21 11/47 Version 1.2


Chapter 2 – Packing List

The unit comes securely packaged in a shipping carton. Please contact your dealer if you find that anything is missing or damaged after examining the contents. The shipping carton should contain the following standard items :

2.1 Standard Items z Driver CD (Include manual) z Printer power extension cable

(24V)

2007/8/21 12/47 Version 1.2

EBN Technology Corp. z IDE extension cable z HDD & CD-ROM power extension cable z Power Cord (The picture varies from the area you locate)

2007/8/21 13/47 Version 1.2


2.2 Optional Items

2 nd

Display

Customer Display (LED, VFD, LCD)

3-in-1 Card Reader (MSR, Smart

Card, i-Button)

RFID

2007/8/21 14/47 Version 1.2


MSR

2007/8/21 15/47 Version 1.2


Getting Started

2007/8/21 16/47 Version 1.2


Chapter 3 – Getting Started

3.1 System setup

Item Photo Description

1

Plug-in power cord and connect with AC power

2 Push “Start Button”

2007/8/21 17/47 Version 1.2


3.2 Hardware Installation

3.2.1 CPU Installation


1 Remove 2 screws

P3 P4

2

Install CPU and apply the thermal adhesive

P3 P4

3 Install thermal module

2007/8/21 18/47 Version 1.2


3.2.2 Memory Installation

The POS system supports memory up to 1 GHz with frequency of DDR266 and

DDR333.

Please follow the below procedures for installation.

1. Remove 2 screws from the system

2. Insert the memory module


1

2

P3

Remove 2 screws

P4

Install Memory module

2007/8/21 19/47 Version 1.2


3.2.3 HDD Installation


1

Remove 2 screws from

HDD cover and pull out the metal case.

2

Install HDD in the metal case.

3

4

Slide the HDD into the

POS system and connect

IDE & Power Cable.

Screw 2 screws on the

HDD cover

2007/8/21 20/47 Version 1.2


3.2.4 OS Installation a. Please prepare a USB CD-ROM . b. Plug a USB CD-ROM into the USB port of POS system . c. Turn on the system and enter CMOS configuration page d. Set the boot up device as USB CD-ROM e. Reboot the system f. Install OS step by step

2007/8/21 21/47 Version 1.2


3.3 Software Installation

3.3.1 Driver Installation


1

2

3

Insert driver CD and select POS 7series

Select your model

(P3 or P4)

P3

Install related driver

2007/8/21 22/47 Version 1.2


P4

2007/8/21 23/47 Version 1.2


3.3.2 Touch Panel Calibration


1

Execute “Touch Panel” from Windows Control

Panel

2

3

Click at “Calibration”

Click at “Calibrate Now”

2007/8/21 24/47 Version 1.2

4


Start calibrate

2007/8/21 25/47 Version 1.2


3.4 Optional Items Installation

3.4.1 MSR / RFID

Install hardware


1

Remove 2 screws from

POS system

2

Remove plastic cover and inverter of system

3

Install the MSR / RFID module on the system

2007/8/21 26/47 Version 1.2

4


Connect MSR cable to

CN12

5 Install inverter

2007/8/21 27/47 Version 1.2


Driver Installation

Item No. Photo Description

1

2

3

Insert driver CD and select POS 7series

Select your model

(P3 or P4)

P3

Install related driver

2007/8/21 28/47 Version 1.2


P4

Also you could install it form the following path.

(CD-ROM):\Driver\Options Driver\MSR(Megnetic Stripe Reader)

Driver\Driver\Disk1\Setup.exe

2007/8/21 29/47 Version 1.2


3.4.2 Pole Display


1 Remove plastic cover

2 Install Pole Display Kit

3

Connect RS232 cable to

COM1

Note:

Be sure to adjust jumper setting of COM1. Modify pin9 to supply 12V power.

For more information, please refer to chapter 5.3

2007/8/21 30/47 Version 1.2

3


3.4.3 2 nd

Display

Hardware Installation


1 Remove plastic cover

2 Adjust POS system angle

Screw on 2 nd

display and plug in the cable

2007/8/21 31/47 Version 1.2


2 nd

Display with touch panel

If you order the 2 nd

display comes with touch panel, please remember to adjust the COM port setting on the bottom side of POS system. So that it could supply

5V DC on pin 1 for touch panel.

Note:

1. The pin 6 of 2 nd

VGA cable supply 12V DC power directly, so it doesn’t need to connect with any external power adapter.

2. The VGA port of the POS system is designed specifically for our display kits. So please do not connect to any normal monitor or LCD.

Pin Assignment

1 RED

2 GREEN

3 BLUE

4 Monitor ID bit 2

5 Ground

9

11

12 no pin (keyway)

Monitor ID bit 0

Monitor ID bit 1

2007/8/21 32/47 Version 1.2


BIOS setup

Chapter 4 – BIOS setup

2007/8/21 33/47 Version 1.2


4.1 P4 M/B

(POS70-2EB-478, POS70-5EB-478)

4.1.1 Starting Setup

To enter BIOS, please click at “Delete” when booting up the POS system and you will see the picture below.

2007/8/21 34/47 Version 1.2


4.1.2 Resolution setup


1

Enter “Northbridge

Configuration” of “Chipset”

2

3

Enter “Flat Panel Type”

12”

Choose your panel type

12” – 800x600

15” – 1024x768

2007/8/21 35/47 Version 1.2


15”

2007/8/21 36/47 Version 1.2


4.2 P3 M/B

(POS70-2EB-370, POS70-5EB-370)

4.2.1 Starting Setup

To enter BIOS, please click at “Delete” when booting up the POS system and you will see the picture below.

2007/8/21 37/47 Version 1.2


4.2.2 Resolution setup


1

Enter “PCI / Plug and Play

Setup” page of BIOS

2

3

Select “LCD Panel Type”

12”

Choose your panel type by

“Page UP” & “Page Down”

12” – 800x600

15” – 1024x768

2007/8/21 38/47 Version 1.2


15”

2007/8/21 39/47 Version 1.2


M/B Information

Chapter 5 – M/B Information

2007/8/21 40/47 Version 1.2


5.1 P4 M/B Jumper Setting

(POS70-2EB-478, POS70-5EB-478)

Clear CMOS Setup

If you want to clear the CMOS Setup (for example forgot the password you should clear the setup and then set the password again.), you should close the

JP1 about 3 seconds, then open again. Set back to normal operation mode.

JP1: Clear CMOS Setup

JP1 Description

1-2

2-3

Keep CMOS Setup

(Normal Operation)

Clear CMOS Setup

Compact Flash Card Master/Slave Mode Setting

JP2: Master/Slave Mode Setting

JP2 Description

OPEN SLAVE

SHORT MASTER

Keyboard Setting

JP3: Keyboard Setting

JP3 Description

Open Disabled

Short Enabled

2007/8/21 41/47 Version 1.2


DCD or DTR Select of COM6 Setting

JP4: DCD/DTR Setting

JP4 Description

1-2 DCD

2-3 DTR

Pentium 4/Mobile P4/Mobile P4-M Select

JP7: Pentium 4/Mobile P4/Mobile Pentium 4-M Select

JP7 Description

1-2 Pentium 4

LCD Power setting

JP8: This jumper is for the setting of LCD panel voltage.

JP8 Description

1-2 +3.3V

3-4 +5V

5.2 P3 M/B Jumper Setting

(POS70-2EB-370, POS70-5EB-370)

Compact Flash Card Master/Slave Mode Setting

JP1: Master/Slave Mode Setting

JP1 Description

OPEN SLAVE

SHORT MASTER

LCD Power setting

JP2: This jumper is for the setting of LCD panel voltage.

JP2 Description

2-4 +3.3V

4-6 +5V

2007/8/21 42/47 Version 1.2


JP2: This jumper is for the setting of LCD panel shift clock.

JP2 Description

1-3

3-5

Inverted

Normal

Clear CMOS Setup

If you want to clear the CMOS Setup (for example forgot the password you should clear the setup and then set the password again.), you should close the

JP5 about 3 seconds, then open again. Set back to normal operation mode.

JP5: Clear CMOS Setup

JP5 Description

2-3

1-2

Keep CMOS Setup

(Normal Operation)

Clear CMOS Setup

ATX / AT Power Use Selection

JP8: This jumper is for the setting of Power use selection.

JP8 Description

OPEN ATX Power

DCD or DTR Select of COM6 Setting

JP10: DCD/DTR Setting

JP10 Description

1-2 DCD

2-3 DTR

2007/8/21 43/47 Version 1.2


5.3 COM & RJ-11 Jumper Settings

Before installing the cash drawer or any peripherals which use COM ports, please make sure you configure all the “Power” settings accurately.

1. Cash Drawer

Cash Drawer

12V 5-6,7-8

24V

JP4

1-2,3-4

2. COM1 & COM2

COM 1 Pin 1 Pin9 COM 2 Pin1 Pin9

12V 19-20 13-14 12V 7-8 1-2

DCD/RI 23-24 17-18 DCD/RI 11-12 5-6

3. COM3 & COM4

COM 3 Pin 1 Pin9 COM 4 Pin1 Pin9

5V 21-22 15-16 5V 9-10 3-4

12V 19-20 13-14 12V 7-8 1-2

DCD/RI 23-24 17-18 DCD/RI 11-12 5-6

5.4 Cash Drawer Introduction

The POS system provides RJ-11 x 2 for cash drawer. And both could support

12V & 24V cash drawer which could be configured on the bottom side of POS system. For more information of configuration, please refer to chapter 3.3.

2007/8/21 44/47 Version 1.2


Pin Assignment

Pin

2

3

Assignment

1 GND

DOUT 0

DIN 0

4 12V/24V

5 NC

6 GND

Pin

7

8

9

10

11

12

Assignment

GND

DOUT 1

DIN 1

12V/24V

NC

GND

I/O Address

I/O Address: 280H (For both Cash Drawers which are controlled by data bit)

Cash Drawer 1: DIN0=>Bit0, DOUT0=>Bit4

Cash Drawer 2: DIN1=>Bit1, DOUT1=>Bit5

2007/8/21 45/47 Version 1.2


Reversion

2007/8/21 46/47 Version 1.2


Chapter 6 – Reversion History

Version Item Descriptions Page

2007/8/21 47/47 Version 1.2

POS-7015EG-370 | EBN Technology Corp. User Manual

Copyright Notice

Trademarks

Contents

Introduction

Chapter 1 – Introduction

System

Main Board

Packing List

Chapter 2 – Packing List

Getting Started

Chapter 3 – Getting Started

BIOS setup

Chapter 4 – BIOS setup

M/B Information

Chapter 5 – M/B Information

Reversion

Chapter 6 – Reversion History

Related manuals

EBN Technology

POS70-2EB-370

ANUBIS

POS50

EBN

EBN

POS60-8B-C1G

GREISINGER

EBNW