Belling | Kensington 1100 DF | Service manual | Belling Kensington 1100 DF Service manual

1
BELLING KENSINGTON 1100 DF
SERVICE MANUAL
2
INDEX
PRODUCT IDENTIFICATION
PAGE
APPLIANCE RATING PLATE .............................................................
3
USER GUIDE AND INSTALLATION HANDBOOK
USER GUIDE..........................................................................................
INSTALLATION INSTRUCTIONS.......................................................
TECHNICAL DATA...............................................................................
CONTACT DETAILS .............................................................................
WIRING DIAGRAM.............................................................................
PARTS LIST DB4 90 E.........................................................................
REPAIR AND MAINTAINANCE
4-33
34-41
42-44
48-48
49-49
50-52
DISASSEMBLY PROCEDURES..........................................................
COMPONANT REMOVAL..................................................................
TECHNICAL SPECIFICATIONS.........................................................
FAULTFINDING GUIDES...................................................................
53-62
62-70
71-71
74-81
THIS MANUAL COVERS THE FOLLOWING MODELS :BELLING KENS 1100 DF
3
PRODUCT IDENTIFICATION
Appliance rating plate location
The appliance rating plate is located on the right-hand side of the
front frame and also on the rear service panel
9
10
YEAR
4
1
8
MONTH
4
4
3
2
8
NUMBER OF PRODUCTION
FOR THE MONTH
4
4
4
0
0
2
8
PRODUCT IDENTIFICATION CODE
It is important that during all service calls the model and serial
numbers are recorded on all paper work.
IMPORTANT NOTICE
Please note the cooling fan fitted to this appliance is an integral part of its safety
and functionality.
When the appliance is installed care must be taken that the cooling fans performance is not impeded by any objects coming into contact with it. (Installation
pipes, leads etc)
Care must also be taken that there is sufficient air flow at the rear of the appliance for the cooling fan to run at its optimum efficiency. (Particularly Built In
appliances) See clearance dimensions in the installation section of the booklet.
During use the Appliance must never be disconnected from the Mains supply as
this will seriously affect the safety and performance of the appliance, particularly
in relation to surface temperatures becoming hot and gas operated parts not
working efficiently.
The cooling fan is designed to run on after the control knob has been switched
off to keep the front of the appliance and the controls cool until the appliance
has naturally cooled itself.
Our Warranty
Should you need it . . . .
Inside the paperwork which has come with this appliance,
there is a leaflet and card explaining the terms of our
extended warranty and guarantee.
In order to apply for a one year guarantee, simply fill in the
details on the card and post it off, this will register your
appliance.
Should you wish to take out extended warranty, please fill
in the details on the leaflet and post this off.
Alternatively, you can register, and apply for extended warranty on line at:
www.belling.co.uk
If your appliance is covered by the warranty and guarantee, you will not be billed for work undertaken should your
appliance be faulty, terms and conditions do apply, so
please read through the literature carefully.
Our Customer Care Centre can be called on:
0871 22 22 503
We aim to answer calls as quickly as possible, and in strict
rotation as soon as one of our Customer Care team
becomes free.
Please ensure that you have available your appliances
model number and serial number, there is a space at the
back of this book for recording that information.
Alternatively visit the web site.
Outside the UK and Northern Ireland, please contact your
local supplier.
For Australia:
Glen Dimplex Australia,
Unit 2, 205 Abbotts Road
Dandenong South
Victoria 3175
Australia
Contents
User’s Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 25
Before Using Your Cooker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
About Your Cooker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Hob & Cooker Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Chip Pan Fires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Using The Clock / Programmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Setting The Programmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using Your Gas Hob. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Using Your Griddle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Using Your Grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Grilling Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using Your Main Oven(s)
Oven & Grill Functions . .
Fanned Oven Guide . . . .
Cooking Guide . . . . . . . .
Roasting Guide . . . . . . .
General Baking Guide . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
12
14
15
16
17
19
Using Your Slow Cook Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Cleaning Your Gas Hob. .
Cleaning Your Cavities . .
Cleaning Your Appliance .
Cook Shop. . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
22
23
24
25
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 - 27
Before You Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Changing Light Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 - 33
Installing Your Cooker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Service Record. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Customer Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
If you smell gas:
Do not try to light any appliance. Do not touch any electrical switch.
Call the Gas Emergency Helpline at TRANSCO on:
0800 111999
Before Using Your Cooker
!
Before using this appliance please make sure that
you have removed all packaging and wrapping.
Some of the furniture inside this
appliance may have additional wrapping.
i
It is also advised that you turn the ovens and/or
grill on for a short while, this will burn off any
residues left from manufacturing. There may be a
smell which accompanies this process - but this is
nothing to worry about and is harmless.
i
We also recommend that you wash the oven
shelves, the baking tray, the grill pan, and the grill
pan trivet before their first use in hot soapy water,
this will remove the protective oil coating.
!
Although every care has been taken to ensure this
appliance has no burrs, or sharp edges, we
recommend that you wear protective gloves when
installing and moving this appliance.
This will prevent any injury.
i
Our policy is one of constant development and
improvement. Strict accuracy of illustrations and
specifications cannot be guaranteed. Modification
to design and material may be necessary
subsequent to publication.
i
Please bear in mind that not all the sections inside
this handbook are relevant to your appliance, but
you should read carefully the sections which are
relevant before installation and use. This will save
you time.
!
Always use a registered installer for this appliance.
Environmental protection:
Stoves are committed to protecting the environment.
All packaging with this appliance is recyclable and
environmentally friendly.
Please recycle whenever possible - contact your
local authority for your nearest recycling centre.
5
!
This appliance is for
use in a domestic
kitchen only, it is not
designed, or intended,
for commercial use.
About Your Cooker
The illustrations below show the different
cavity and hob layouts available within
dual fuel ranges.
A
= Programmeable oven
(see timer section)
Small
burner
Wok
burner
Medium
burner
Medium
burner
Small
burner
Large
burner
Wok
burner
Small
burner
Medium
burner
Medium
burner
Large
burner
Medium
burner
Griddle
Position
Fascia
panel
Slow
AA
AA
Grill
Fascia
panel
Grill
A
Multifunction
oven
A
Fanned oven
Fanned oven
Slow cook
oven
Multifunction
oven
6
Hob & Cooker Safety
Always ensure that pan bases are dry, and flat before
!
using them on the hob.
Always position pans over the centre of the burner,
and turn the handles to a safe position so they cannot
be knocked or grabbed.
Always use pans which are no smaller than 100mm
(4”), or larger than 250mm (10”).
Always take care when removing food from the oven
as the area around the cavity may be hot.
Always use oven gloves when handling any utensils
which have been in the oven as they will be hot.
Always make sure that the oven shelves are resting in
the correct position in between two runners. Do not
place the oven shelves on top of the highest runner,
this will lead to spillage and injury if the baking tray, or
dish falls.
Never use double pans, rimbased pans, old or
misshapen pans, or any pan which is not stable on a
flat surface.
Never leave cooking fat, or oil, unattended.
Never use commercial simmering aids, or heat
diffusers, as they create excessive heat and can
damage the surface of the hob.
Never use the hob for any other purpose than cooking
food.
Plastic cooking utensils can melt if they come into
contact with a warm hob. Never leave them close to,
or on top of, the hob.
Never leave the burner alight without a pan covering it.
This causes a fire hazard.
Do not place items of the door while it is open.
Do not wrap foil around the oven shelves, or allow it to
block the flue.
Do not drape tea towels near the oven while it is on,
this will cause a fire hazard.
Do not pull heavy items, such as turkeys, or large
joints of meat, out from the oven on the shelf, as they
may overbalance and fall.
Do not use this appliance to heat anything other than
food items, and do not use it for heating the room.
7
WARNING: Parts of
the appliance may
become hot while in
use, always make sure
that children are
supervised when they
are near to the
appliance.
Always make sure that the
burner caps, rings and
pansupports are correctly
placed. This will prevent pans
becoming unstable while in
use, and ensure an
uninterrupted gas flow.
i
Call Customer Care for
a service engineers visit
if:
You find over a period of
time that the gas oven
becomes hotter at a
particular temperature - the
thermostat may need
replacing.
The cooling fan fails to
work.
Chip Pan Fires
What causes a chip pan fire?
Chip pan fires start when oil of fat overheats and catches fire,
or when oil or fat spills on to the cooker because the pan has
been filled too high.
They can also start when wet chips are put into hot oil,
making it bubble up and over flow.
Preventing a chip pan fire
Never fill the pan more than a third full with oil of fat.
Never leave the pan alone with the heat on - even for a few
seconds.
Dry chips before putting them in the pan.
Never put chips in the pan if the oil has started smoking.
Turn off the heat and leave the oil to cool down, or else it
could catch fire.
In the event of a chip pan fire
If your chip pan does catch fire - don’t panic, and don’t move
the pan. Serious burns are often caused by picking up the
pan and running outside with it.
If it is safe to do so, and you don’t have to reach across the
pan, turn off the heat.
Never throw water, or use a fire extinguisher.
If you can, drape a damp cloth or towel over the pan to
smother the flames.
Leave the pan to cool down for at least half an hour.
If you can’t control the fire yourself, close the door, get out
and tell everybody else to get out.
Call the fire brigade. Don’t go back inside whatever the
reason.
8
Using The Programmer/Clock
Through your programmer you will be able to set the time
of day, set the minute minder, and use the semi and fully
automatic cooking functions. The programmer is vital to
the working of your appliance, and reading this section will
make sure that you get the most out of your ovens.
What your timer symbols
mean.
A
The programmer buttons
There are three buttons on this type of timer. The table
below shows you what their symbols look like, depending on
the model type, and what they do.
Symbol
Symbol
What is it?
Down / Minus
-
Used to decrease cook / end time, remove
minutes from the minute minder and adjust
the time of day.
Also for listening to and setting the alarm
tone.
Up / Plus
+
Used to increase cook / end time, add minutes
to the minute minder and adjust the time of
day.
Function button
Used to select the functions available on this
timer.
Press once for: Minute Minder.
Press twice for: Cook time
Press three times for: End time.
How to use these functions is explained later
on in this section.
Setting the time of day
Press the Plus and Minus buttons together for a few
seconds, and release.
The ‘’ in between the numbers on the LED Display will
begin to flash.
While the ‘’ is flashing it is possible to adjust the time
using the Plus and Minus buttons.
Once the time has been set, allow approximately 30
seconds before using any of the other timer functions.
This ensures that the time will remain correct.
Setting an alarm tone
There are three tones to choose from.
Press and release the minus button.
Once the minus button is released, the tone is selected.
9
i
This is a 24 hour clock.
Before you do anything
with your appliance you must set the correct time of day.
A
Using The Programmer/Clock
Setting the minute minder
To set the Minute Minder, press the Function button
once. The bell symbol will appear and start flashing.
The flashing only lasts for 5 seconds so the time must be
set within this time frame.
Use the Plus and Minus button to set the length of time
required. Once this has been done, the Minute Minder
is set.
When the desired length of time has counted down the
alarm will sound. To cancel the tone, press any of the
buttons.
To cancel the Minute Minder at any time, press the Plus
and Minus buttons together.
Semi - Automatic Cooking
The Duration method
Switch off after a set time period
Press the Function button twice, which will skip past the
Minute Minder.
The display will flash the word ‘dur’, and the ‘A’ will flash
on the left hand side of the display.
Use the Plus and Minus buttons to set the length of time
you want to cook for. This must be done within 5
seconds or the time of day will show again.
Once this is done the oven will automatically switch off
once the time has elapsed, and the alarm will sound. To
switch off the alarm, press any button.
To view any remaining time press the function button
twice.
The End Time method
Switch off at a set end time
Press the Function button three times, which will skip
past the Minute Minder and the Duration programmer.
The display will flash the word ‘End’ and the ‘A’ will flash
on the left hand side of the display.
Use the Plus and Minus buttons to select the time the
oven is required to turn off.
Once this is done the oven will turn itself off at the time
you have selected. To switch off the alarm, press any
button.
A
A
A
A
A
A
10
Setting the Programmer
A
Fully Automatic Cooking
Switch on and off automatically
This requires both the duration and the end time to be
entered. The timer will work out the start time and begin
cooking.
Press the Function button twice, which will skip past the
Minute Minder.
The display will flash the word ‘dur’, and the ‘A’ will flash
on the left hand side of the display.
Use the Plus and Minus buttons to set the length of time
you want to cook for. This must be done within 5 seconds or the time of day will show again.
Press the Function button three times, which will skip
past the Minute Minder and the Duration programmer.
The display will flash the word ‘End’ and the ‘A’ will flash
on the left hand side of the display.
Use the Plus and Minus buttons to select the time the
oven is required to turn off.
Once this is done the oven will turn itself off at the time
you have selected. To switch off the alarm, press any
button.
Set the temperature of the oven and place the
food inside.
The timer will calculate the appropriate start time.
When using the Programmer:
Do:
Familiarise yourself with the use of the programmer.
Select foods which are as fresh and as cold as possible
preferably straight from the refrigerator.
Choose foods which are suitable for cooking from a cold
start, as some dishes will be affected by being left
uncooked, at room temperature.
Make sure that meat, poultry and uncooked food are
thoroughly thawed before placing them in the oven.
Cover dishes with lids or foil.
Try to keep the end time as close to your return as
possible.
Do not:
Place warm food in the oven for delayed cooking foods
must be thoroughly cooled before placing in the oven,
the oven must also be cool before you start.
Cook dishes containing left over cooked meat or poultry,
or pastry dishes with wet fillings, they are not suitable!
Over-fill dishes containing liquids.
A
A
A
A
A
11
i
The automatic cooking
symbol will appear to
show that the oven is
no longer in manual
mode but in automatic
mode.
i
Important: Once the
oven has switched itself
off please make sure
you turn to oven controls to the ‘off’ position
and set the oven to
manual by pressing the
Cook Time and Ready
Time buttons together.
i
Important: Remove
food as soon as it is
cooked.
Using Your Gas Hob
Hob Ignition
Models without thermocouples:
To turn on, place your pan onto the pansupports above
the burner you wish to use.
Push in and turn the selected control knob
anticlockwise, to the full on symbol.
If your hob has an ignition button or switch on the fascia, press it in until your burner lights.
If your hob has automatic ignition it will spark next to
the burner when you push in the control knob.
To simmer, turn the control knob to the small flame
symbol. This will ensure that the flame is just large
enough to gently heat the contents of the pan.
To turn off, turn the control knob clockwise to the ‘off’
position.
Always make sure that your pans are place correctly on
the burners as shown, and do not allow the flame to
extend over the base of the pan.
Models with thermocouples:
Igniton as above, but:
Hold the control knob in for 15 seconds. Do not hold
the control knob in for any longer than 15 seconds. If
the burner fails to light within this time, release the
control knob and wait one minute before attempting to
re-ignite.
i
Picture A below:
shows a burner without
thermocouples.
Picture B below:
shows a burner with
thermocouples.
12
A
B
!
!
Energy Saving
Position pans centrally over the elements.
Only heat the amount of liquid you need.
Once liquids have been brought to the boil, reduce the
heat setting to a simmer.
Consider using a pressure cooker if possible.
Vegetables in small pieces will cook quicker.
Use a pan which is a close match to your element size.
Smaller elements are ideal for simmering and stewing
in smaller pans, while the larger elements are ideal for
frying and boiling
How can I tell if my hob
has thermocouples?
i
In the event of a power
failure, or the ignition
not working:
Push in and turn the
control knob to start the
gas, then hold a lighted
match or taper to the
burner until it lights.
i
Use flat based pans
which are the correct
size for your burners
and suitable for your
hob type.
We recommend the
following sizes:
100mm or 4” min.
250mm or 10” max.
Smaller or larger pan
sizes may lead to slower
cooking times.
Using Your Griddle
Only use the griddle which has been approved for use on
this appliance. Do not use any other griddle, as this may
be hazardous.
Please read these instructions thoroughly before using the
griddle for the first time.
!
Always make sure that
children are supervised when they are
near to the appliance
when it is in use.
Before using the griddle for the first time
Wash the griddle thoroughly in hot soapy water. (see
“Cleaning” section).
Season sparingly with a minimum amount of cooking oil.
Heat the griddle on full rate for 3 minutes. The griddle
plate is now ready for use.
!
Always allow the griddle
to cool completely before
moving or cleaning.
Using the griddle
The griddle should only be positioned front-to-back
over the burners indicated by the griddle symbol on the
fascia panel.
Do not use the griddle over the large burners.
Place the griddle carefully on the pan support over the
burners, using the locating feet on the underside of the
griddle. Take care to avoid damage to the surface of the
pan supports.
Before cooking, preheat the griddle for 3 minutes on full
rate, which is indicated on the control knobs by a large
flame symbol.
After preheating, turn the control knobs to the small
flame symbol.
The griddle is now ready for cooking.
Do not use metal implements, as they may damage the
non-stick surface.
Note:
Using a gas appliance results in the production of heat
and moisture in the room in which it is installed. Always
ensure that the room is well ventilated: keep natural
ventilation holes open, or install a mechanical ventilation
device (i.e. an extractor hood). Prolonged use of the
appliance may call for additional ventialtion, for example
opening a window, or more effective ventilation such as
increasing the level of mechanical ventilation where
present.
13
i
About your griddle:
The griddle is made of
quality cast iron, and
has a non-stick cooking
surface.
Regular seasoning will
prolong the life of the
griddle and prevent
rusting. If the griddle
shows signs of rust,
wash and re-season.
i
Seasoning the
griddle: see the
‘Cleaning’ section of this
handbook.
Using Your Grill
Before you start grilling. . . .
Before you use the grill, make sure you have placed the
grill shelf in the position you need as once the grill is on
you may injure yourself if you try to move the shelf.
i
Warning: Accessible
parts may become hot
when the grill is in use.
Chidren should be kept
away.
Do not close the door while the grill is in use.
Turn the selector control knob to the heat setting you
require.
To switch off, return the control knob to the ‘off’
position.
The cooling fan will come on during use, and may
continue to run for some time afterwards.
To adjust your results, you can turn the grid over, or
remove it altogether.
i
Types of grill
Fixed rate grill: has a
full ‘on’ setting and ‘off’.
Variable rate grill: has
adjustable heat settings
1 (low) to 8 (high) or 5
(high) - depending on
the model.
Single grill: has one grill
element.
If your grill is a dual grill:
The dual grill uses all of the top element and is ideal for
grilling large quantities of food.
The single grill uses part of the element only, and is
better suited to grill smaller amounts of food.
The grill pan
This appliance comes with a grill pan, grill pan handle and
a grid.
The handle of the grill pan is detachable to allow you to
remove it while the pan is in use, this stops it from
getting hot.
Dual grill: has two grill
elements which can be
used together, or as a
single grill.
i
For best results:
Pre-heat the grill for
about 3 minutes.
i
Please note: the grill
pan handle is designed
for sliding the grill pan
into and out of the grill
cavity. It is not to be
used for lifted the pan.
To attach the handle:
Place the handle over the narrow edge of the grill pan
and slide to the centre as shown in the diagrams.
Shelf & Grid adjustments
Speed of grilling can be adjusted by changing the shelf
position or the turning the grill pan grid.
High: For thin foods and toasting.
Low: For thicker meat pieces.
Aluminium Foil
Never cover the grill pan or grill trivet with foil, or allow fat
to build up in the grill pan, as this creates a fire hazard.
14
grid
grill pan
handle handle position
indicators
Grilling Guide
Food
Type
Bacon
Shelf
Position
Time Approx
(mins)
5
8 - 15
5
4
3
2
1
Sausages
5
12 - 15
Chops
Lamb
Pork
4
3
10 - 15
15 - 25
Toast
2 rounds
4 rounds
5
5
Note:
Shelf positions are
counted from the
bottom up.
i
As with any cooking
guide, all times are
approximate and can be
adjusted to suit
personal taste.
1 - 2 (per side)
1 - 2 (per side)
Bread products
Buns
Tea cakes
4
4
1 - 2 (per side)
1 - 2 (per side)
Cheese on toast
2 rounds
4 rounds
5
5
4-5
4-5
Fish:
fillets
2
10 - 15
Chicken:
fillets
i
Depends on thickness
1-2
20 - 30
Beef Steaks:
rare
medium
well done
5
4
4
7 - 10
10 - 15
15 - 20
Gammon Steaks
5
12 - 15
15
Using Your Main Oven
The main oven may be controlled by the programmer (see
The Programmer/Clock for details).
The programmer, if fitted must be set to manual before it
can be used, or programmed.
Switching on the multifunction oven
Use the function control knob to select the function you
wish to use - see the functions table for details.
Note: You can change function during cooking if you
wish, as long as the oven is in manual mode.
Turn the temperature control knob to the temperature
you wish to use.
The thermostat indicator will come on to show that the
oven is heating, and once the temperature is achieved,
it will go out.
To switch off the main oven, simply turn the control
knob back to the ‘ ‘ position.
The cooling fan will come on during use, and may continue to run for some time afterwards.
16
i
Important: Never
place food, or dishes on
the base of the main
oven, the element is
here and it will cause
over heating.
Using Your Main Oven
The main oven may be controlled by the programmer (see
The Programmer/Clock for details).
The programmer, if fitted, must be set to manual before it
can be used, or programmed.
Switching on the fanned oven
Use the main oven control to turn your oven on, and
select your temperature.
The thermostat indicator will come on to show that the
oven is heating, and once the temperature is achieved,
it will go out.
To switch off the main oven, simply turn the control
knob back to the ‘ ‘ position.
The cooling fan will come on during use, and may
continue to run for some time afterwards.
17
i
Important: Never
place food, or dishes on
the base of the main
oven, the element is
here and it will cause
over heating.
Oven & Grill Functions
The chart below details all of the functions which are available. Your oven may
not have all of the functions shown here.
Main Oven Function
Recommended Uses
Base Heat Only
Used to finish off the bases of food following cooking using the conventional
or fanned modes. The base heat can be used to provide additional
browning for pizzas, pies and quiche. Use this function towards the end of
cooking.
Top Heat Only
The heat is ideal from browning off the tops of food as it is not as fierce as
the grill following conventional or fanned cooking. Provides additional
browning for dishes like Lasagna or Cauliflower cheese. Use this function
towards the end of
cooking.
Conventional Oven
Intensive Bake
This function is ideal for traditional roasting. The meat is placed in the
middle of the oven, roast potatoes towards the top.
Suitable for food with a high moisture content, such as quiche, bread and
cheesecake. It also eliminates the need for baking pastry blind.
Fanned Grill
The fan allows the heat to circulate around the food. Ideal for thinner foods
such as bacon, fish and gammon steaks. Foods do not require turning. Use
with the oven door closed.
Fanned Oven
The even temperature in the oven makes this function suitable for batch
baking, or batch cooking foods.
Defrost
To defrost foods, such as cream cakes/gateaux, use with the oven door
closed. For cooling dishes prior to refrigeration, leave the door open.
Dual Grill
Single Grill
This function cooks food from the top and is ideal for a range of food from
toast to steaks. As the whole grill is working, you can cook larger quantities
of food.
For smaller quantities of food, but is still ideal for
anything from toast to steaks.
Base Heat with Fan
Used to cook open pies (such as mince pies) the base element ensures that
the base is cooked while the fan allows the air to circulate around the filling
- without being too intensive.
Lights only
Use when the oven is switched off and cold to aid cleaning the oven cavity.
18
Fanned Oven Guide
Some adjustment will have to be made to conventional
cooking temperatures.
The table below shows conventional cooking
temperatures, fanned temperatures and gas marks.
For optimum results using the fanned oven setting,
conventional temperatures need to be converted to the
fanned oven temperatures.
For example and item which would cook at 180˚C will
now cook at the fanned oven temperature of 160˚C.
This is a high efficiency oven, you may notice an
emission of steam when the door is opened.
When cooking chilled or frozen foods, use the
recommended cooking times and temperature on the
packaging. Always make sure the food is piping hot
throughout before serving.
There are no zones of heat, and no flavour transfer
when using a fanned oven - allowing you to cook a
greater variety of foods together.
If you are cooking on more than one shelf, you may
need to slightly increase the cooking time.
Always make sure that there is enough space between
dishes, to allow food to rise, and to air to circulate.
Conventional
temp (˚C)
‘A’ Efficiency oven
(˚C)
Gas mark
100
100
1/4
110
110
1/4
130
120
1/2
140
130
1
150
140
2
160
150
3
180 - 190
160
4-5
200
170
6
220
180
7
230
190
8
250
200
9
19
Cooking Guide
Pre-heating
To get the best results from your oven, we recommend
pre-heating for around 5 to 15 minutes before placing
your dishes in. This is especially important for items
which are chilled, frozen, batter based, yeast based or
whisked sponges.
If you are using a fanned function, you should still preheat but for a shorter time.
The items in the cooking guide below are based on a
pre-heated oven, but can be adjusted to take into account
personal taste.
Oven and bakeware
Always use high quality trays and tins for cooking. Poor
quality tins and trays can warp in the oven producing
uneven results.
Never use dishes which are cracked, damaged or not
oven proof as heating may lead to shattering inside the
oven.
Food Type
Temp.
Setting ˙C
Time
Approx.
Shelf
Position
Conv
Fanned
Intensive
Cakes
Small cakes
Victoria sandwich
Semi rich fruit cake
Christmas cake
190
180
150
150
160
160
125
125
-
15 - 25
20 - 30
21/2 - 3hrs
21/2 - 3hrs
7 & 13
7
5
3
Puddings
Bread & butter
pudding
Fruit crumble
170
200
150
175
-
45 - 1hr
40 - 1hr
9
9
Miscellaneous
Yorkshire pudding:
large
small
Shortcrust pastry
220
220
200
200
200
180
200
200
180
40 - 45
15 - 20
depends on
filling
11
12
top - middle
20
Roasting Guide
Roasting times depend on the weight, shape and texture
of the meat and personal preference. In order to
calculate the roasting time, weigh the meat or poultry,
including the stuffing, and follow the times given
below.
Meat joints (including chicken) should be roasted at
180 - 200˚C Conventional/ 160 - 180˚C Fanned for
20 - 30 mins per 450g/1lb, plus 20 minutes on shelf
position 2.
Frozen meat must be thoroughly thawed before
cooking. For large joints, it is advisable to thaw
overnight.
Frozen poultry must be thoroughly thawed before
cooking. The time required depends on the size of the
bird - eg: a large turkey may take up to 48 hours to
thaw.
When cooking stuffed meat or poultry, calculate the
cooking time from the total weight of the meat plus the
stuffing.
Cooking joints in foil, covered roasters, lidded
casseroles, or roasting bags will help to reduce meat
shrinkage, give a more moist result and may reduce fat
splashing. However, a slightly longer cooking times will
be required, add 5 - 10 minutes per 450g (1lb) to the
calculated cooking time. When using roasting bags do
not exceed the temperatures recommended by the
manufacturer, and do not allow the roasting bag to
touch the sides or top of the oven.
Use of a trivet with the roasting tin will reduce fat
splashing during open roasting, and will help to keep the
oven interior clean.
The use of a roasting tin larger then that supplied is not
advised, as this may impair performance and lead to
extended cooking times.
21
Roasting Guide
Roast turkey
Roasting turkey perfectly involves cooking two different
types of meat - the delicate light breast meat, which
must not be allowed to dry out, and the darker leg meat,
which takes longer to cook.
The turkey must be roasted long enough for the legs to
cook, so frequent basting is necessary. The breast meat
can be covered once browned.
Turkey should be roasted at 180 - 200˚C
Conventional/ 160 - 180˚C Fanned for 20 - 30 mins
per 450g/1lb, plus 20 minutes.
The turkey can be open roasted, breast side down, for
half of the cook time, and then turned over for the
remainder of the cooking time.
If the turkey is stuffed, add 5 minutes per 1lb to the
cooking time.
If roasting turkey covered with foil, add 5 minutes per
1lb to the cooking time.
To test if the turkey is cooked, push a fine skewer into
the thickest part of the thigh. If the juices run clear, the
turkey is cooked. If the juices are still pink, the turkey
will need longer cooking. Always make sure that the
turkey is cooked properly before serving.
Turkey Roasting times.
Most Turkeys are measured by the kilogram. Timing should
be calculated in either of these ways:
40 minutes per 1kg plus 10 minutes per 1/4 kg.
or
20 minutes per 1lb, plus 20 minutes.
The maximum size Turkey for this appliance is: 20lbs
approximately 9kgs.
Please do not attempt to roast a Turkey larger than this, as
the results cannot be guaranteed.
22
General Baking Guide
Trouble-shooting - Fruit Cakes
PROBLEM
POSSIBLE CAUSE
Fruit sinking to the bottom
Low oven temperature which may cause the cake to
take longer to set, allowing the fruit to sink. Or, too
much liquid, or raising agent. The fruit may not have
been properly washed and dried.
Cake sinking / dipping in the centre
Too much raising agent in the mixture. Too hot, or too
cool an oven. Or, not enough liquid or insufficient
creaming.
Surface cracks
Too small a tin, or too much mixture in the tin. Too
much raising agent in the mix, plus not enough liquid
or insufficient creaming. The oven may be too hot.
Hard outer crust with a damp patch inside
Oven too hot, therefore the cake baked too quickly.
Too much sugar, or insufficient liquid.
Burnt outside
Oven temperature too high. Oven too small for the
size of cake. Insufficient protection around the tin.
Cake baked on too high a shelf.
Texture with pronounced holes.
Too much raising agent. Flour unevenly mixed.
Texture too close and cake insufficiently risen.
Not enough raising agent. Not enough liquid. Too
cool an oven. Insufficient creaming.
Cake crumbles when cut
Not enough liquid. Baked for too long. Not enough
sugar. Too much baking agent.
Too dry
Over baking. Insufficient egg or liquid. Too much raising agent.
Trouble-shooting - Sponge Cakes
Domed top
Insufficient creaming of mixture. Cake baked on too
high a shelf position, or at too high a temperature.
Paper liners can cause the outer edge not to rise and
the centre to peak.
Hollowed / sunken top
Too much raising agent. Oven temperature too low, or
incorrect shelf position. Cake removed from oven
before it’s cooked. Use of soft tub margarine.
Very pale, but cooked
Oven temperature too low. Baked too low in the oven
Overflowing tin
Tin too small for the amount of mixture
23
Using Your Slow Cook Oven (if fitted)
Introduction
One of your oven compartments is an electric oven which
provides a gentle heat suitable for slow cooking or keeping
food warm. The slow cook element is positioned in the
base of the lower compartment - always make sure that the
cooking pot is placed centrally on the base of this compartment.
Do not use the compartment to store food or canned
items.
Cooking times
The cooking time varies according to the type of food being
cooked, and experience will show how long foods should be
cooked for, according to personal taste and preference.
In general foods should be cooked for at least 5 hours, and
may be left up to 8 - 10 hours without spoiling if covered.
Foods cooked using the slow cook oven will take about
three times longer than they would in a conventional oven.
Utensils
Any oven proof utensils may be used for slow cooking provided they have a close fitted lid.
To rectify a badly fitting lid a piece of cooking foil may be
placed over the dish, under the lid.
The most useful utensils for slow cooking are the flame
proof type which can be used over direct heat and for oven
cooking, and are sufficiently attractive to use as serving
dishes.
Benefits of Slow Cooking
Slow cooking has always been the best way to prepare hot
meals with the minimum of preparation and maximum time
away from the kitchen.
The advantages of slow cooking are as follows:
Food can be left to cook unattended for several hours
and will keep hot for several hours if left covered.
Inexpensive cuts of meat become
deliciously tender
when slow cooked. There is also a reduction in meat
shrinkage.
Dishes such as soups, vegetables, puddings savoury
dishes and preserves are also suitable for slow cooking.
There is no topping up of steamers, steam filled kitchens
or constant checking to do.
24
Using Your Slow Cook Oven ( if fitted)
Keeping food warm
Turn the oven control knob to the on position, and place
the food in the oven. If food is to be kept moist then it is
important to cover the dish or plate to prevent food from
drying out. This can be done using aluminium foil if the
dish does not have a lid.
Do not use cling film to cover food.
Some foods are best left uncovered if you wish to keep
the food dry and crisp.
Do not add gravy to plated meals until serving.
Carved meat should be placed on one plate and covered,
adding just one tablespoon of gravy to keep it moist.
When keeping plated meals warm it is recommended
that the food is placed on hot rather than cold plates.
Slow Cooking
Turn on the slow cook oven and place the prepared
cooking pot centrally on the base of the oven. Follow the
guide lines for the best results.
The maximum capacity of ovenproof dishes should be no
more than 2.5 litres (4.5 pints). Please note: The more
you fill the dish/pot the longer it will take to cook.
All meat and poultry recipes need a minimum of 5 hours
to cook.
Make sure all frozen ingredients are well thawed out.
Cut root vegetables into smaller pieces as they take
longer than meat to cook. If possible they should be
sauteed for 2 - 3 minutes before slow cooking.
Ensure that root vegetables are always at the bottom of
the pan immersed in the cooking liquid.
A meat thermometer should be used when cooking pork
joints and poultry. The internal temperature of the food
should reach 88˙C,
Stuffed meat or stuffed poultry should not be slow
cooked. Cook any stuffing separately.
Cover casseroles with a lid, or foil to prevent loss of
moisture.
Adjust seasoning and thickening at the end of cooking
time.
Opening the door during cooking, leads to heat loss, and
will lead to increased cooking times.
25
Cleaning your Gas Hob
Sometimes when a hob is not working well, it is because
it needs cleaning.
Enamel parts
Use a mild cream cleaner for example ‘Cif’. Stubborn
marks can be removed with a soap filled pad.
Stainless steel surfaces
Only use a clean cloth wrung out with warm, soapy
water and dried off with a soft cloth. For stubborn
marks use a specialist stainless steel cleaner.
Do not use steam cleaners.
Sharp implements and objects can mark the surface of
stainless steel, however they do become less noticeable
in time.
Cast iron parts
Ensure the parts have fully cooled and scrape off any
stubborn marks, and bits of food with a plastic, or
wooden cooking implement. Rinse in warm soapy
water and dry with a tea towel.
Do not clean in a dishwasher.
If you notice any rusting on your griddle, or
pansupports, simply clean in warm soapy water, then
re-season.
Burner caps and heads
The slots in the burner head where the flames burn
should be cleared of deposits.
Clean with a nylon brush, rinse and then dry
thoroughly. There may be brownish coloured markings
on your burners, these are carbon deposits or fat stains
and can be removed using a soap filled pad.
Do not put burners in the dishwasher or soak them.
Using dishwasher powders, washing up liquids and
caustic pastes can damage the burners.
Burner caps and heads must be repositioned correctly
so that they sit squarely on to the hob as shown on the
the left.
This is particularly important with stainless steel models
as failure to reposition the caps correctly may result in
discolouration of the stainless steel around the burners.
!
Always allow your
appliance to cool
down, and switch off
the electricity before
you clean any part of
it.
i
Baby oil can be used to
restore stainless steel
finishes - but only use a
few drops. Don’t use
cooking oils as they can
contain salts which will
damage the metal.
i
Don’t use:
undiluted bleaches,
products containing
chlorides, wire wool or
abrasive cleaners on
aluminium, stainless
steel, or plasitic/painted
parts they can damage
the appliance. Nylon
pads can also be
unsuitable
i
Seasoning the
griddle:
Pour a drop of unsalted
cooking oil onto the
cooking side of the
griddle, use kicthen roll
to cover the griddle
evenly. Olive oil is not
suitable for seasoning.
Regular seasoning
prevents rust.
burner cap
correct
parallel
burner head
incorrect
angled
burner cap not central
Painted & Plastic parts
Only use a clean cloth wrung out in hot soapy water.
26
incorrect
Cleaning your Cavities
Cleaning the oven cavities
Some foods can cause fat to spit, especially if you have
open roasted, this leaves the inside of the cavity
greasy.
It is important to clean the oven cavity as a build up of
fat can damage the appliance and may invalidate your
guarantee.
!
Chrome plated parts.
Use a moist soap filled pad, or place in a dishwasher.
Shelf runners can be removed to enable you to clean
then thoroughly. Make sure they are cool to touch and
then grasp the runners and slide out of their hanging
holes.
Pristine enamel surfaces
The enamel can be cleaned by wiping the surfaces
with a clean cloth which has been wrung out in hot,
soapy water.
If larger splashes of fat do not readily disappear, you
can use a mild cream cleaner to remove them. More
stubborn marks can be removed using a soap filled
pad.
Rinse well, and allow to dry before use.
Vitreous enamel surfaces
The enamel can be cleaned by wiping the surfaces
with a clean cloth which has been wrung out in hot,
soapy water.
Stubborn marks can be cleaned using a moistened
soap filled pad, or a mild cream cleaner.
Rinse well, and allow to dry before use.
27
Always allow your
appliance to cool
down, and switch off
the electricity before
you clean any part of
it.
i
Don’t use:
Caustic or abrasive
cleaners, bleaches,
coarse wire wool or
hard impliments,
these will damage
your appliance.
i
Using a trivet while
roasting meat may help
to reduce fat splashes.
Cleaning your Appliance
Painted & Plastic parts
Only use a clean cloth wrung out in hot soapy water.
Do not use abrasive cleaners, such as “Cif”, wire or nylon
cleaning pads on these parts.
Stainless steel & Aluminium surfaces
Only use a clean cloth wrung out in hot soapy water, and
dry with a soft cloth.
Stubborn marks can be removed using a stainless steel
cleaner. Supplies can be purchased from the Customer
Care Centre.
Sharp objects can mark the surface of stainless steel, but
will become less noticeable with time.
Wipe any spillage immediately, taking care to avoid burning your hands.
Some foods are corrosive eg; vinegar, fruit juices and
especially salt - they can mark or damage the metal if
they are left on the surface.
Enamel surfaces & parts
Clean with warm, soapy water and a clean cloth.
Dry with a soft clean towel or cloth.
Do not use steam cleaners.
Glass parts
Only use a clean cloth wrung out in hot soapy water, or
a specialist glass cleaner.
Rinse away any excess cleaner and dry with a soft cloth.
Do not use abrasives or polishes as they will scratch and
damage the glass.
The inner door glass panel can be removed for cleaning
but it must be replaced the right way up. If there is any
writing on the glass, you must be able to read it clearly
when the cavity doors are open.
Always make sure that the glass is pushed fully into the
Stop position.
To remove the glass panel, open the door wide, hold the
top and bottom edges and slide out.
Warning: Do not operate the appliance without the glass
panel correctly fitted.
!
Always allow your
appliance to cool
down, and switch off
the electricity before
you clean any part of
it.
i
Take extra care when
cleaning over symbols
on fascia panels,
excessive cleaning can
lead to the symbols
fading.
i
Baby oil can be used to
restore stainless steel
finishes - but only use a
few drops. Don’t use
cooking oils as they can
contain salts which will
damage the metal.
i
Don’t use:
undiluted bleaches,
products containing
chlorides or abrasive
cleaners on aluminium
or stainless steel, they
can damage the
appliance.
Glass door panels
For your safety, glass door
panels are made of toughened
glass. This ensures that, in
the unlikely event that a panel
breaks, it does so into small
fragments to minimise the risk
of injury.
Please take care when
handling, using or cleaning all
glass panels, as any damage
to the surfaces or edges may
result in the glass breaking
without warning or apparent
cause at a later date.
Should any glass panel be
damaged, we strongly
recommend that it is replaced
immediately.
28
Cook Shop
Product
description
Product
code
Quantity
Where used
Rectangular
carbon filters
082612620
2
Hoods
Round carbon
filters
082611571
1
Hoods
Ceramic hob
scraper kit
082606781
1
All ceramic glass
hobs including
induction.
Ceramic hob
cleaner and
conditioner
082606780
1
All ceramic glass
hobs including
induction
Sealed hotplate
conditioner
082606783
1
All sealed / solid
plate hobs.
Stainless steel
cleaner
082606764
1
All stainless steel
parts
Oven cleaner
spray
082606786
1
All cookers, inside
cavities and on
glass.
Multi-purpose
kitchen
cleaner
082606782
1
General kitchen
cleaner.
E-cloth
082813300
1
All cookers, for
cleaning glass and
stainless steel
29
To order or enquire about any
of these products, please call
the Spares Sales team on:
0870 458 9961.
Before you call. .
Problem?
The ignition won’t work.
(Gas and dual fuel models)
Advice
Check there is a spark when the
ignition button is depressed. If
there is no spark, check the
electricity supply is switched on at
the socket.
Check that the gas supply is
switched on.
Try another appliance in the
socket, if that works replace the 3
amp fuse in the cooker plug.
There’s condensation on the
doors.
Condensation is caused by hot,
moist air meeting a cooler surface
(i.e. the oven door). You cannot
always prevent it, but you can
minimise it when it happens by
doing the following:
Pre-heat the oven at a high
temperature before putting food in
the oven, and cover the food you
are cooking wherever possible.
Whenever you can, cook wet
foods at higher temperatures.
Don’t leave food in the oven to
cool down.
Automatic cooking will normally
produce condensation when the
oven is cooling down with food
inside.
There’s been a power failure
and the oven won’t work.
(models with clocks and
automatic programmers)
Switch off the electricity supply.
When the power returns - re-set
the programmer/Clock to the
correct time of day.
This will allow you to use your
appliance.
30
Changing Light Bulbs
Warning: There is a risk of electric shock, so always
make sure you have turned off and unplugged your
appliance.
Not all appliances have the same number and type of
bulbs. Before replacing your bulb, open the top/main
oven door and see which type you have. Then use the
table to help you change your bulb correctly.
Please remember that bulbs are not covered by
your warranty.
Bulbs can be purchased from hardware stores (always
take the old bulb with you).
No. of
lamps
Bulb
Location
Oven
type
Instruction for
changing the bulb
2
(@25W)
side
All
Wait until the oven is cool,
then remove the oven
shelves.
Grasp the lens cover on the
light fitting and pull it away
from the side of the oven.
Unscrew the bulb.
1
(@25W)
rear
Fanned /
Multifunction
Wait until the oven is cool,
then remove the shelves.
The oven light is at the rear
of the oven cavity.
Remove the loose oven back
- unscrew the 4 securing
screws (one at each corner).
Unscrew the lens cover (turn
anticlockwise). Unscrew the
bulb and replace. Replace
lens cover and replace oven
back.
1
(@25W)
rear
Conventional
Wait until the oven is cool,
then remove the oven
shelves.
The oven light is at the rear
of the oven cavity.
Unscrew the lens cover (turn
anticlockwise). Unscrew the
bulb and replace. Replace
lens cover.
31
There is no need to remove
the oven back on the 90DF
model.
Installing Your Cooker
Clearances
This cooker may be fitted flush to the base units of your
kitchen.
No shelf, overhang, cupboard, or cooker hood should
be less than 650mm above the hob top, but please
check this with the hood manufacturers instructions.
If your appliance has a side opening door, we
recommend a side clearance of 60mm to allow the
oven door to fully open.
The cooker must have a side clearance above hob level
of 90mm up to a height of 400mm.
The important dimensions are those around the
appliance.
&$
&$
"#$
%$$
'
(
)$$
*$$
&$$
+$$$
++$$
+,$$
32
Installing Your Cooker
The information below is crucial to installing this appliance
correctly and safely.
Ventilation Requirements
The room containing the appliance should have an air
supply in accordance with BS 5440:Part 2.
All rooms require an openable window, or equivalent,
and some will require a permanent vent as well.
For room volumes up to 5m3 an air vent of 100cm3 is
required.
If the room has a door which opens directly to the
outside, or exceeds 10m3 - no air vent is required.
For room volumes between 5m3 and 10m3 and air vent
of 50cm2 is required.
If there are other fuel burning appliances in the same
room, BS 5440:Part 2 should be consulted to determine
the air vent requirements.
This appliance must not be fitted into a bed sitting room
of less than 20m3 or into a bath or shower room.
Windows and vents should not be blocked or removed
without first consulting a competent engineer.
LPG only - do not install this appliance below ground
level. This does not preclude installation into rooms which
are basements with respect to one side of the building, but
open to ground level on the opposite side.
Australian
Gas Safety (Installation & Use) Regulations
This appliance must by an authorised person in accordance with the manufacturers installation instructions,
local gas fitting regulations, the AGA Gas Installation, the
Australian Gas Installation Code AG601 / AS5601 and
any other relevant statutory regulations.
Particular attention should be given to relevant requirements regarding ventilation.
Where standards have been revised - always use the most
recent edition.
Failure to install appliances correctly is dangerous
and could lead to prosecution.
33
Installing Your Cooker
The information below is crucial to installing this appliance
correctly and safely.
UK Regulations & Standards
always refer to the most recent issue of the standards
Gas Safety Regulations.
Building Regulations - issued by the DEFRA.
Building Standards (Scotland) (Consolidated) - issued by
the Scottish Development Department.
I.E.E. Wiring Regulations.
Electricity at Work Regulations.
BS 6172 Installation of Domestic Gas Cooking. For LP
Gas, refer to BS 5482 Part 1, Part 2 or Part 3 as
relevant.
Installation and Servicing Instructions for this appliance.
For installation in countries other than the UK, the appliance
must be connected in accordance with all local gas and
electrical regulations.
In the Republic of Ireland installers should refer to IS 813
Domestic Gas Appliances.
Failure to install appliances correctly is dangerous
and could lead to prosecution.
34
Installing Your Cooker
Fitting the plinth (if applicable)
Make sure the appliance is raised to a height of 915mm
or above before beginning. If the appliance is below
915mm - you can only fit the plinth cover labelled X.
You can adjust the height using the feet (1) of the
appliance.
If your appliance has a storage drawer at the bottom,
you access the required holes through the base of the
drawer after lifting the mat.
Oven cavity
Door
0
-+.
1
Open the appliance doors, and loosen screw A located
on bracket (2). Do not remove this screw entirely.
Insert screw B, through slot (3) and screw into the small
hole at the bottom of bracket (2).
Make sure that the plinth cover is flush to the appliance,
but not over tightened.
-,.
-/.
Plinth cover
Fitting the splashback (if applicable)
Loosley fit screw A and nut B into hole 1 at both ends of
the rear surface of the appliance.
Locate fitted screw A through the slots in both of the
metal splashback plates.
Tighten screw A and nut B.
Now locate and tighten screw C and nut D through hole
(2) at both ends of the rear surface of the appliance.
Make sure that the splashback is securely attached, but
avoid over tightening.
-+.
2
Fitting the towel rail (if applicable)
On the towel rail there are two hole, top (A) and bottom
(B), these holes have corresponding holes on the fascia
at each end.
The screw for the top hole (A), must be screwed into
the supplied adaptor, whereas the remaining screw just
goes through the bottom hole (B). Both screws are M6
screws. Using the allen key provided, tighten the screws
making sure that the towel rail is flush to the fascia,
but not over tightened.
35
-,.
Installing Your Cooker
34
-
.
Stabilising and Securing
5
6
Your cooker may come with a stability chain, if it does not
we recommend that you buy a stability bracket from your
local supplier, this will keep the cooker from moving and
will prevent damage to the flexible hosing at the back of
the cooker.
Your stability chain
3
Your cooker must be secured to a wall or a solid partition
behind the cooker.
Your stability bracket
You can buy a stability bracket from your supplier and it
can fitted as follows:
Place the cooker in position and draw a pencil line level
with the front edge.
Remove the cooker and mark off 450mm from the
pencil line to locate the front edge of the lower
bracket.
Fix the bracket to the floor. Measure from floor level
to engagement edge in the back of the cooker and add
3mm.
Assemble the underside of the top part of the bracket
to this height.
See the drawings for the location of the bracket and
the recommended positioning.
Levelling
Once your cooker is secure:
Place a spirit level onto a baking tray, on an oven shelf.
These cookers are fitted with adjustable feet which will
allow you to adjust the height of the appliance until it is
level. The adjustable feet are at the rear of the cooker.
Rear wall
Stability bracket
Front edge for
lower bracket
3
450
mm
0
1 Pencil line
on floor
2 Centre
of range
5
8 4
36
5 Underside of top bracket
slots into engagement
edge in back of cooker.
Installing Your Cooker
Connecting the electricity supply
For Australia:
For your own safety we recommend that your cooker be
installed by a competent person. The cooker should be
installed in accordance with AS/NZS 3000:2000
Warning:
This appliance must
be earthed!
We recommend that this appliance is connected by a competent person, who is a member of a recognised
“Competent Persons Scheme” and who will comply with
the I.E.E. and local regulations.
The appliance must be installed using a multi-pole control
unit of 30 Ampere minimum capacity with 3mm minimum
separation at all poles.
Ensure that you route all mains electrical cables well clear
of any adjacent heat source, such as an oven or grill.
Where a fixed connection is used, a device allowing the
appliance to be isolated on all poles from the mains supply with a contact opening width of at least 3mm must be
provided.
After connection to the electricity please check that all
electrical parts are working.
The maximum power rating is specified in the Technical
Data section of this handbook, and also on the Data
Badge on the appliance.
This appliance must be fitted using a double pole unit
of 30 ampere minimum capacity with 3mm minimum
contact at all poles.
Access to the mains terminal is gained by opening the
terminal block cover at the rear of the appliance - use
a flat bladed screw driver for this.
Connection should be made with a 6.0mm2 twin and
earth cable.
First strip the wires. then push the cable through the
cable clamping the terminal block cover.
Connect the cable to the terminal block and tighten the
cable clamp screw - see diagram.
Close the terminal box, ensuring that the cover is
engaged on the locking tabs.
Sufficient cable should be used to allow the cooker to
be pulled out, but must hang clear of the floor so it
does not become twisted or trapped when the cooker
is pushed back.
37
PHASE 1
PHASE 2
PHASE 3
L1
L2
L3
4
5
Neutral
Cable
clamp
Earth
(Green / Yellow
or sleeving)
Installing Your Cooker
Connecting to the gas supply
The inlet to the appliance is ISO 7 - Rp 1⁄2” internal thread
situated towards the top right corner of the rear.
Fit the bayonet connection. This should be located so as
to ensure that the flexible hose does not kink.
Use a 900mm - 1125mm length of flexible hose.
Ensure that all pipe work is of the correct rating.
Natural Gas - Flexible connections should comply with
BS 669. Parts of the appliance likely to come into contact
with a flexible connector have a temperature of less than
70˙C.
LP Gas - For flexible connections use a bayonet type
hose, suitable for use on LP Gas up to 50mbar pressure
rise and 70˙C temperature rise. The flexible hose should
be coloured black with a red stripe, band or label. If in
doubt, contact your supplier.
After installation make sure all connections are gas
sound.
Commissioning
Pressure settings:
G20 Natural Gas @ 20mbar
G30 Butane @ 28-30mbar
G31 Propane @ 37mbar
Hob
Turn on gas supply and check for soundness at the hotplate injector. Light two burners and check that the pressure is correct.
Grill
Turn the control knob to the full on position and ignite,
allow the grill to operate for a few minutes.
Oven
Turn the control knob to the full on position and ignite,
allow the oven to operate for a few minutes.
38
Installing Your Cooker
Connecting to the gas supply
Means of isolation shall be provided at the shut off point by
either an approved quick connect device or a Type 1 manual shut off valve. The outlet of t he quick conn ect device
shall be at, or below, the horizontal position.
Connection to t he g as suppl y should be made using th e
Aquaknect AS /NZS 18 69 cl ass B hose assembly with an
internal diameter of not less than 10mm (supplied with the
appliance) a nd regulator (regul ator for use with natural
gas)
NOTE: Maximum length of hose 900mm.
The temperature rise of the areas at the rear of the cooker
that are likely to come into contact with the flexible hose do
not exceed 70˙C.
Ventilation requirements
Ventilation must be as specified by AS5601 Installation code.
The room containing the appliance should have an air sup ply.
An applia nce should be installed i n a locati on for complete
combustion of gas, proper flueing and to maintain ambient
temperature o f th e immediate sur rounding at safe limits,
under normal conditions.
LP Gas only - Do not install this appliance in a room below
ground level. This does not preclude installation into rooms
which are basements with respect to one side of the build ing, but open to ground level on the opposite side.
Failure to install appliances correctly is dangerous and could
lead to prosecution.
After installation make sure all connections are gas
sound.
Commissioning
Pressure settings:
Natural Gas - 1.0 kPa
Butane - 2.75 kPa
Propane - 2.75 kPa
Hob
Turn on gas supply and check for soundness at the hotplate injector. Light two burners and check that the pressure is correct.
39
Technical Data - Notes
Australia
Type of gas:
Europe & Russia
Type of gas:
Natural Gas I2H
Please see data badge your for specified gas
Natural Gas II2H3+*
type. * Can be converted from Natural gas to LP Gas
LP Gas I3+
Please see your data badge for specified gas Never attempt to convert an appliance type.
unless the data badge states that you can.
* Can be converted from Natural gas to LP Gas
Never attempt to convert an appliance unless the data badge states that you can.
Burner Aeration:
Fixed
G20
G30
G31
G30
G31
G25
Pressure setting:
Natural Gas @ 20mbar
Butane @ 28-30mbar
Propane @ 37mbar
Butane @ 50mbar
Propane @ 50mbar
Natural Gas @ 25mbar
Burner Aeration:
Fixed
Pressure setting:
Natural Gas - 1.0 kPa
Butane - 2.75 kPa
Propane - 2.75 kPa
Electrical supply:
230V / 400V 3N ~ 50Hz
All elements are rated at 230V
Countries of destination:
Australia
Electrical supply:
230V / 400V 3N ~ 50Hz
All elements are rated at 230V
Countries of destination:
Great Britain
Ireland
France
Holland
Germany
Russia
Belgium
40
Technical Data - Notes
Fuel Type Hotplate Burner / Nominal Rate
Element
Qn
Natural Gas
LP Gas
Hob
Hob
Hob
Hob
-
small
medium
Large
wok
1.0kW
2.0kW
3.0kW
3.5kW
Total heat input
5 burners
7 burners
11.5kW
14.5kW
Hob
Hob
Hob
Hob
small
medium
Large
wok
1.0kW
2.0kW
3.0kW
3.5kW
Total heat input
5 burners
7 burners
11.5kW
14.5kW
-
Butane
g/h
Propane
g/h
Injectors
used
-
-
77
104
129
121 & 63
-
-
73
145
218
254
72
143
215
250
50
70
87
87 & 35
Fuel Type
Dual Variable
grill
(90 & 100 size)
Dual Variable
grill
(110 size)
Multifunction
oven
(all)
Fanned oven
(all)
Electric
@ 230V
1.6 - 2.5kW
1.6 - 2.6kW
2.3kW
2.3kW
Slow cook
oven
(if fitted)
Oven lamps
0.16kW
25W each
Appliance size
90cm
100cm
110cm
Maximum load
7200W
7370W
7465W
41
Technical Data - Notes
Australian hob / hotplate - Technical Data
Fuel Type
Hotplate Burner /
Element
Natural Gas
Hob
Hob
Hob
Hob
LP Gas
Nominal Rate
Qn
Butane
g/h
Propane
g/h
small
medium
Large
wok
3.6MJ/h
7.2MJ/h
10.8MJ/h
12.6MJ/h
-
-
Total heat input
7 burners
51.5MJ/h
-
-
Hob
Hob
Hob
Hob
small
medium
Large
wok
3.8MJ/h
7.2MJ/h
10.2MJ/h
12.6MJ/h
-
-
Total heat input
7 burners
52.0MJ/h
-
-
-
-
42
Conversion Instructions
This conversion kit is for use on the following appliances:
Dual Fuel - all sizes.
This conversion kit is to be used to convert the above appliances from:
UK Appliance Nat Gas to LP - Natural Gas G20 @ 20mbar to LPG G30/31 @
29/37mbar
UK Appliance LP to Nat Gas - LPG G30/31 @ 29/37mbar to Natural Gas G20 @
20mbar
UK to German LPG G30/G31 @ 50 mbar
UK to Australian NG @ 1.0kPa
UK to Australian ULPG @2.75kPa
Before beginning conversion, ensure that the Gas and Electricity supplies have been
turned off. The full conversion must be completed - i.e. you must change the injectors
and the by-pass pins.
Important: The conversion procedure must be carried out by a suitably qualified person
i.e. Corgi registered. After conversion all affected parts must be checked for gas soundness.
Injectors & Bypass Screws
UK / Europe NG
Hotplate burner
Injector
Auxiliary ( Small)
Semi Rapid
(Medium)
Rapid (Large)
77
104
129
Semi Rapid
(Medium)
Rapid (Large)
50
70
87
Auxiliary ( Small)
Semi Rapid
(Medium)
Rapid (Large)
46
61
79
Auxiliary ( Small)
Semi Rapid
(Medium)
Rapid (Large)
Wok
Inner
Outer
63
121
UK / Europe LP (Excluding Germany)
Hotplate burner
Injector
Auxiliary ( Small)
Wok
Inner
Outer
35
87
Germay LP
Hotplate burner
Injector
Wok
Inner
Outer
35
77
Australian NG
Hotplate burner
Injector
82
118
142
Bypass
63
63
77
Auxiliary ( Small)
Semi Rapid
(Medium)
Rapid (Large)
Wok
Inner
Outer
72
138
Australian ULPG
Hotplate burner
Wok
Inner
Injector
50
70
87
Bypass
32
39
45
43
Outer
35
87
80
Conversion Instructions
To convert the hotplate burners
a) Remove the pan supports
b) Remove the burner caps and burner heads
c) Unscrew the existing injectors from the hotplate burner bowls
d) Replace with the injectors supplied in the conversion kit as detailed in the tables on
the previous page.
Note: when converting the wok burner, it is necessary to replace the two injectors, the
inner and outer. The outer injector is visible on removal of the cover plate.
UK / Europe / Russia
To convert the gas tap bypass screws
a) Remove the hotplate control knobs springs and bezels
b) Using a small flat bladed screwdriver, each bypass screw can be accessed
via the hole in the inner fascia panel
c) NG to LP - Turn each bypass screw fully clockwise until it stops.
Do not over tighten
d) LP to NG – Turn each bypass screw anti-clockwise until a small, stable
flame is maintained when the control is turned to simmer.
The flame must not be extinguished when wafted.
e) Refit the control bezels, springs and control knobs.
Conversion labels
Conversion to LP (excluding Germany)
After conversion, affix the label supplied with the conversion kit
PER/FOR G30/G31 adjacent to the appliance data badge
Conversion LP Germany
After conversion, affix the label supplied with the conversion kit
PER/FOR G30/31@50mbar adjacent to the appliance data badge
Conversion to NG
After conversion, affix the label supplied with the conversion kit
PER/FOR G20 adjacent to the appliance data badge
44
Australian Conversion Instructions
UK to Australia NG / ULPG
To convert the hotplate bypass screws
a) Remove the hotplate control knobs, springs and bezels
b) Using a small, flat bladed screwdriver, each bypass screw can be
accessed via the hole in the inner fascia panel
c) Undo the bypass screw by turning in an anti-clock wise direction, when
fully un-screwed the bypass screw can be removed using a pair of long
nosed pliers.
d) Replace with the bypass screws supplied in the conversion kit as detailed
in the tables on the previous page
e) Turn the bypass screw fully clockwise until it stops. Do not over tighten.
Conversion labels
Conversion to Australian NG
After conversion, add the label stating “ONLY FOR USE WITH NATURAL GAS”
adjacent to the appliance gas inlet.
Conversion to Australian LP
After conversion, add the label stating “ONLY FOR USE WITH PROPANE GAS”
adjacent to the appliance gas inlet.
45
Service Record
Please record your model number and serial number in the space below.
Where are my model and serial numbers?
Freestanding HL appliances:
Freestanding appliances:
Built in oven:
Hobs:
base of storage drawer
front frame near oven cavity
front frame near oven cavity
base plate of the hob
Having these numbers to hand will help us to help you, quickly and more efficiently.
When contacting us, please use the Customer Care number on the back cover of this
handbook.
Model Number
Serial Number
Date of purchase
Installer stamp / Printed name
Date of installation
Place of purchase:
Date
Part(s) replaced
48
Engineers Stamp/
Printed Name
BELLING KENSINGTON 1100DF - AU
ISSUE A
Wiring colour code: Bk-Black, Bn-Brown, Bu-Blue, Gn-Green, Or-Orange, R-Red, W-White, Y-Yellow, Gy-Grey, V-Violet
572
LH
OVEN
NEON
RH OVEN NEON
Bk
PUSH ON
EARTH TAB
ADD SLEEVE neon
lead 08-24897-00
RH SIDE
COOLING
FAN
64
Bk
Or
2
4,N
THERMOSTAT
444
LH MAIN
OV
1
Or
472
P1,L
435
W
P1
Bn
2
Bn
Bu
Bk
432
2
Bk
THERMOSTAT
444
GRILL REG.
P2
1
PILOT
P2,B
2,A
2
Bu
Y
421
1
Bu
W
Bk
P1
Bu
8
7
6
5
4
3
2
Rd
P2
1
Bn Y
1
565
572
R
L
R
Bu
421
32
Y
LH TOP FRONT
THERMAL
SWITCH
512
IGNITION
SWITCH
444
LH REAR
THERMAL
CUTOUT
422
N
410
F70C
W
W L150C
Or
Bn
407
Bn
Bn
32
PROGRAMMER
P1
Y
101
423
534
Bn
203
Rd Bn
407
P8
P7
P6
P5
P4
P3
P2
570
V
102
Gn
2
SELECTOR SWITCH
RH MO
1
Bk
Bn
2
RH OVEN
SWITCH
64
423
Gn
572
565
Bk
RIGHT HAND
OVEN LAMP
415
431
ADD SLEEVE neon
W 423
lead 08-24897-00
508
421
LH SIDE
COOLING
FAN
570
Door Switch Harness
08-24678-00
Or
Bu
32
Gn
Bn
449
448
565
L
431
472
W
40
205
Rd
Bk
Bk
Gn
Or
565
IGNITION
GENERATOR
8 Outlet
Generator
Only
Bu
506
Gn
Bk
Bk
Or
569
RH OVEN
TOP
ELEMENT
435
N
Bk
DOOR
MICROSWITCH
RH OVEN FAN
ELEMENT
Gn
Gn
Bk
Gn
L100C
473
422
Y
RH OVEN
BASE
20
ELEMENT
LH MAIN
OVEN
STIR
FAN
Or
Bk
Gn
414
LH MAIN OVEN
FAN
ELEMENT
32
Bk
Y
Y
Gn
Gn
571
414
205
435
Bk
Bn
2
1
P1
L150C
Bn
ADD SLEEVE neon
lead 08-24897-00
P2
51
571
427
R
RH REAR
THERMAL
CUTOUT
64
Or
51
Bu
Gn
L
463
Bn
Bk
Or
SLOW COOK
ELEMENT
32
Bk
Bk
V
572
SLOW COOK
SWITCH
506
LH OVEN
LAMP
101
427
SLOW COOK
NEON
Gn
501
Gn
Bk
416
Gn
Bn
LH TOP REAR
THERMAL
CUTOUT
64
501
1
473
Bk
Bk
Bn
Or
RH OVEN
STIR
FAN
Y
LH GRILL ELEMENT
Or
435
Gn
N
INLET TERMINAL BLOCK
PUSH ON
EARTH TAB
CIRCLED NUMBERS INDICATE WIRE PART NUMBER:
BASE NUMBER 08-24564-XX, WIRES 1 TO 99.
BASE NUMBER 08-2474-1XX, WIRES 101 TO 199.
BASE NUMBER 08-2485-2XX, WIRES 201 TO 299.
BASE NUMBER 08-2503-3XX, WIRES 301 TO 399.
BASE NUMBER 08-2462-4XX, WIRES 401 TO 499.
BASE NUMBER 08-2462-5XX, WIRES 501 TO 599.
BASE NUMBER 08-2517-6XX, WIRES 601 TO 699.
© This diagram is the property of Glen Dimplex Home Appliances. Not to be reproduced or transmitted in any shape or form without the permission of Glen Dimplex Home Appliances 29/01/07
PRODUCT:
COLOUR:
CODE:
ISSUE:
DATE:
Key
026
026
032
0358
0358
037
037
037
037
037
037
037
037
037
037
037
037
040
057
057
0813
0813
083
084
085
086
090
091
092
094
094
102
103
104
105
108
108
108
108
113
114
147
147
178
182
182
182
206
207
207
210
210
211
Product
082060800
082060800
082566100
602925403
602925402
082851722
082851704
082851721
082851703
082851706
082851724
082851720
082851702
082851719
082851701
082851718
082851700
083029901
502895700
502895700
502925501
502925501
082519300
082519400
082519500
082546707
082957800
082957801
082957802
082546900
082547000
082957700
082957701
082957702
082546801
081586001
081586001
081586001
081586001
081718425
082566200
082533800
082533800
082520000
082101600
082101600
082101600
531805900
562802005
562895813
602598709
602598709
082291500
BELLING K'SINGTON 110DF-IN crm
Cream
444449063
RANGE
Product Description
BEARING door
KB
BEARING door
KB
BEZEL switch
Blk
FRONTFRAME 55 std
mot
FRONTFRAME 55 std
mot
BEZEL energy regulator
Nic
BEZEL grill
Sta
BEZEL multifunction switch Nic
BEZEL mf switch
Sta
BEZEL slow cook
Sta
BEZEL slow cook/warmer
Nic
BEZEL t/stat fanned
Nic
BEZEL tstat elec fanned Sta
BEZEL t/stat multifunction Nic
BEZEL tstat elec mf
Sta
BEZEL h/p
Nic
BEZEL h/p
Sta
BLOCK terminal PA223Sn/6
BRACKET plinth
BRACKET plinth
STRUT stiffener 55
STRUT stiffener 55
BURNERBOWL aux (0.77) Defendi
BURNERBOWL semi (1.04) Defendi
BURNERBOWL rapid (1.29)Defendi
BURNERBOWL wok ng(63/121) tc
BURNERCAP aux (serie3)blk gls
BURNERCAP semi (serie3)blk gls
BURNERCAP rapid(serie3)blk gls
BURNERCAP wok inner-gloss
BURNERCAP wok outer-gloss
BURNERSKIRT aux (serie 3)
BURNERSKIRT semi (serie 3)
BURNERSKIRT rapid (serie 3)
BURNERSKIRT wok
BUSH cavity support
BUSH cavity support
BUSH cavity support
BUSH cavity support
BUTTON timer
Blk
BUTTON switch
Nic
CATCH roller (nylon)
CATCH roller (nylon)
CLIP spring Defendi
CLIP tubular
CLIP tubular
CLIP tubular
FLUE oven assy
COVER PLINTH inner 110
blk
COVER plinth 110
blk
mot
FANCOVER 60 flue lamp
FANCOVER 60 flue lamp
mot
COVER flue vent
TCO
19/03/09
18/06/09
15/06/09
15/06/09
22/06/09
15/06/09
29/06/09
23/01/09
19/03/09
12/08/2008
Replace
Date Qty
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
7
7
1
1
1
2
1
2
3
1
1
2
3
1
1
1
2
3
1
1
2
2
2
2
3
1
1
1
7
4
4
4
1
1
1
1
1
1
PRODUCT:
COLOUR:
CODE:
ISSUE:
DATE:
Key
247
0249
0396
0398
247
0249
0396
0398
247
0249
0396
0398
247
0249
0396
0398
248
248
252
252
253
253
279
281
286
286
287
287
287
293
293
294
294
294
294
294
294
295
314
314
315
315
319
0299
0300
349
349
388
402
410
411
411
411
411
418
420
420
420
421
421
Product
012561015
602561006
082894400
082894501
012561015
602561006
082894400
082894501
012561014
602561006
082894400
082894501
012561014
602561006
082894400
082894501
562859011
562859010
562858905
562858905
601823319
601823319
082547100
082532602
082230600
082354202
082971200
082971900
081561400
082971800
082971500
081561600
082971300
082971302
082971300
082971302
081561600
082010701
082233400
082233400
081581800
081581800
012848654
082848100
082848102
081830501
081830501
082825101
082554901
082469100
082517700
602517700
602517700
082517700
502975400
082917304
082917304
082917300
082917305
082917301
BELLING K'SINGTON 110DF-IN crm
Cream
444449063
RANGE
Product Description
DOOR INNER 55 main rh assy mot
DOOR INNER 55 main win lh mot
GLASS outer door Ranges
GLASS inner rg 50/55 main ken
DOOR INNER 55 main rh assy mot
DOOR INNER 55 main win lh mot
GLASS outer door Ranges
GLASS inner rg 50/55 main ken
DOOR INNER 55 main lh assy mot
DOOR INNER 55 main win lh mot
GLASS outer door Ranges
GLASS inner rg 50/55 main ken
DOOR INNER 55 main lh assy mot
DOOR INNER 55 main win lh mot
GLASS outer door Ranges
GLASS inner rg 50/55 main ken
DOOR OUTER 55 main w rh be crm
DOOR OUTER 55 main w lh be crm
DOOR OUTER 55 top be
crm
DOOR OUTER 55 top be
crm
DOOR INNER 55 top
mot
DOOR INNER 55 top
mot
ELECTRODE wok 900mm long lead
ELECTRODE 1300mm DEL703
ELEMENT base
KB
ELEMENT base slow cook 160w
Element gr/dual 20.35715.000
Element ov/top 20
20.35721.000
35721 000
ELEMENT grill dual
KB
Element base 20.35726.000
Element base 20.35729.000
ELEMENT oven fan (2.5kw) KB
Element oven fan 20.35718.000
ELEMENT oven fan 20.35719.010
Element oven fan 20.35718.000
ELEMENT oven fan 20.35719.010
ELEMENT oven fan (2.5kw) KB
ELEMENT oven top
KB
FAN cooling DP203A-2123LST-C31
FAN cooling DP203A-2123LST-C31
FAN oven circulation
FAN oven circulation
FACIA assy be ken 110dfin blk
ENDCAP facia lh
Blk
ENDCAP facia rh
Blk
FOOT levelling long
FOOT levelling long
GENERATOR ignition DG441
GRIDDLE ribbed universal
GRIP handle grill pan
Blk
GRILL PAN (vit enamel)
GRILLPAN std
mot
GRILLPAN std
mot
GRILL PAN (vit enamel)
Blk
GUARD wiring
GUIDE shelf large lh
1978
GUIDE shelf large lh
1978
GUIDE shelf small lh
1974
GUIDE shelf large rh
1979
GUIDE shelf small rh
1975
TCO
20/04/09
99/99/99
99/99/99
99/99/99
09/09/2009
99/99/99
99/99/99
99/99/99
12/01/2008
27/04/09
12/01/2008
12/01/2008
18/05/09
18/05/09
12/01/2008
04/06/2009
23/03/09
23/03/09
Replace
Date Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
PRODUCT:
COLOUR:
CODE:
ISSUE:
DATE:
Key
421
424
424
427
428
428
428
428
455
455
458
458
459
459
472
5044
0522
525
544
544
557
574
580
614
615
697
697
697
706
728
728
728
728
728
728
733
733
734
734
734
736
738
738
749
749
749
791
791
791
806
823
Product
082917305
082738101
082738100
082283705
082851800
082851800
082851800
082851800
082905900
082905900
082856400
082856400
082856401
082856401
502582513
082606772
012860205
082830202
926016900
926016900
082044000
082930600
082938800
082843600
082843601
562044129
562044129
562988200
082590900
080180676
080180676
080215764
080180676
080215764
080180676
081797201
081797201
081797200
081797200
081797200
081423974
080180734
080180734
082917403
082917403
082917403
082554300
082554300
082554300
081511001
082494402
BELLING K'SINGTON 110DF-IN crm
Cream
444449063
RANGE
Product Description
GUIDE shelf large rh
1979
HANDBOOK Bell 900/1100DF Int
HANDBOOK Bell 900/1100DF range
HANDLE grill pan
1041
HANDLE assy door
Chr
HANDLE assy door
Chr
HANDLE assy door
Chr
HANDLE assy door
Chr
HINGE drop down door (Zan)
HINGE drop down door (Zan)
HINGE bottom
HINGE bottom
HINGE top
HINGE top
HOTPLATE 110 gas fsd
sta
BELLING BADGE BBELLING013
KIT conversion rg lpg aus
KNOB gas h/p o universal Blk
LAMP assy oven
LAMP assy oven
LOCKNUT foot
NEON SL332250010T
NUT flanged locking
PANSUPPORT cast be
PANSUPPORT cast be wok
PLINTH 55
blk
PLINTH 55
blk
PLINTH 110
blk
REGULATOR energy MPA-V02SV
SCREW m6x30 pp mc
SCREW m6x30 pp mc
WASHER fibre 11/64" dia
SCREW m6x30 pp mc
WASHER fibre 11/64" dia
SCREW m6x30 pp mc
SEAL grill
KB
SEAL grill
KB
SEAL main ov 550HL
KB
SEAL main ov 550HL
KB
SEAL main ov 550HL
KB
SEAL tap 4mm COPRECI F3862-04
SCREW m4x12 tt pcsk ch blk
SCREW m4x12 tt pcsk ch blk
SHELF main oven 452 wide 1970
SHELF main oven 452 wide 1970
SHELF main oven 452 wide 1970
SPACER oven fan
SPACER oven fan
SPACER oven fan
SPRING COMPRESSION CONTROL BZ
STRIKER door (silver)
TCO
18/03/09
22/01/09
22/01/09
Replace
Date Qty
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
12
1
1
2
3
6
3
1
1
1
1
1
2
2
2
2
2
2
0.98
1.3
1.46
0.32
1.46
7
4
4
2
1
2
3
3
2
12
1
PRODUCT:
COLOUR:
CODE:
ISSUE:
DATE:
Key
823
835
835
876
878
878
879
880
880
881
882
888
889
890
894
895
906
909
910
912
917
917
922
945
945
950
967
991
Product
082494402
082963200
082963200
082578200
081811101
082859700
082859800
082808901
081545403
082558101
082808902
082964501
082964500
082964603
082964601
082964602
082965800
082938701
082938700
082558001
082874000
082966600
562586711
562586611
562851911
562867306
082518800
030116310
BELLING K'SINGTON 110DF-IN crm
Cream
444449063
RANGE
Product Description
STRIKER door (silver)
Counter support
Counter support
SWITCH door ROLD
SWITCH ignition E2009
SWITCH selector 42.08000.041
SWITCH on/off 42.07900.008
SWITCH thermal L100c
SWITCH thermal cut-out 150c
SWITCH m/ov 42.02400.008
SWITCH thermal fan
TAP semi 0.32 bp lh set 0.46
TAP aux 0.27 bp lh set 0.46
TAP wok 0.68 bp rh set 1.07
TAP semi 0.32 bp rh set 0.46
TAP rapid 0.40 bp rh set 0.60
thermocouple wok
Thermocouple 500mm long
Thermocouple 300mm short
THERMOSTAT EGO 55.17069.090
TIMER (programmer 900)
TIMER (prog)EL143/ESK1457-001
HOTPLATE SIDE 110
blk
VENT TRIM 110 st
blk
VENT TRIM 110 be
blk
EXTRUSION facia rg 110 lip blk
WIRE TRIVET grill pan
1130
WHEEL assy
TCO
24/11/08
17/04/09
Replace
Date Qty
1
2
2
1
1
1
1
1
2
2
1
2
2
1
1
1
1
3
3
2
1
1
2
1
1
1
1
1
1
BELLING
KENSINGTON 110 DF
REPAIR
AND
MAINTAINANCE
PROCEDURES
2
IMPORTANT
BEFORE CARRYING
OUT ANY SERVICING
WORK ALWAYS
DISCONNECT FROM
THE ELECTRICAL
SUPPLY
3
1) REMOVING THE MAIN OVEN DOOR
REMOVE THE 2 SCREWS FROM
THE LOWER HINGE AS
INDICATED.
REMOVE THE LOWER HINGE
AND SLIDE THE DOOR
DOWNWARDS AWAY FROM THE
TOP HINGE
ENSURE THAT THE DOOR IS
SUPPORTED AT ALL TIMES
2) REMOVING THE TOP OVEN DOOR
OPEN THE DOOR FULLY
RELEASE THE 2 CLIPS AND PUSH
FULLY BACK INTO POSITION
SHOWN
CLOSE DOOR TO REST POSITION
AND LIFT TO REMOVE DOOR AND
HINGE
WHEN REPLACING ENSURE THAT
HINGES ARE FULLY ENGAGED IN
THE HINGE BUSH
4
REMOVING THE HINGE FROM THE DOOR
REMOVE THE 2 SCREWS AS
INDICATED
PULL THE HINGE OUT OF THE
DOOR EXTRUSION
5
3) REMOVAL OF HOB TOP
REMOVE ALL HOB BURNERS
REMOVE 15 X SCREWS SECURING
THE BURNERS TO THE HOB TOP
REMOVE 6 X SCREWS AT THE REAR
OF THE FACIA PANEL AS SHOWN
REMOVE 2X SCREWS ONE EITHER
SIDE AS SHOWN
6
REMOVE 4 X SCREWS (2 EITHER
SIDE) AS SHOWN THAT SECURES THE
VENT TRIM
THE HOB TOP CAN NOW BE REMOVED FROM THE APPLIANCE
7
4) REMOVAL OF SIDE PANELS
REMOVE 2X SCREWS AT REAR OF
APPLIANCE
REMOVE 2X SCREWS FROM FRONT
OF APPLIANCE
REMOVE SIDE PANEL
8
5) REMOVAL OF FACIA PANEL
REMOVE THE 6 SECURING SCREWS
IN REAR OF FACIA PANEL (IN HOB)
REMOVE 2 X SCREWS AS SHOWN
REMOVE 4 X SCREWS FRON UNDERSIDE OF FACIA PANEL
REMOVE THE FACIA COMPLETE
WITH TIMER
6) REMOVING THE REAR SERVICE PANEL
REMOVE SECURING SCREWS X6
REMOVE REAR SERVICE PANEL
WITH CARE SO AS NOT TO
DISCONNECT ANY OF THE WIRES
CONNECTED TO THE TERMINAL
BLOCK
9
REAR SERVICE PANEL REMOVED
cooling fans
7) DOOR SEALS
THE DOOR SEAL IS REMOVED BY
JUST PULLING IT IS SECURED IN THE
GAP BETWEEN THE CAVITY AND
FRONFRAME AND REQUIRES NO
OTHER FIXING
TO REFIT PUSH IN ALWAYS ENSURE
THAT DOOR SEAL LIP IS FACING
CORRECT WAY
10
REPLACEMENT OF COMPONANTS
A) ELECTRODES
FOLLOW STEP 3 AND
REMOVE THE HOB TOP
REMOVE ELCTRODE CLIP BY
SQEEZING TOGETHER AND PULLING
TO REMOVE
REMOVE ELECTRODE FROM
BURNER BOWL AND IGNITION LEAD
FROM IGNITIION GENERATOR
ON REPLACING ALWAYS ENSURE
THAT THE RUBBER WASHER IS
REFITTED
B) HOB THERMOCOUPLES
FOLLOW STEP 3 AND REMOVE THE
HOB TOP
REMOVE UPPER NUT USING A 7mm
SPANNER
REMOVE THE THERMOCOUPLE
FROM THE BURNERBOWL
ON REPLACING ALWAYS ENSURE
THAT THE RUBBER WASHER IS
REPLACED TO REDUCE DISTURBANCE TO THE FLAME DUE TO THE
COOLING FAN
11
C) GAS TAPS
FOLLOW STEP 3 AND REMOVE THE
FACIA PANEL
REMOVE 1 SCREW AS SHOWN ON
EITHER SIDE
PULL FORWARD INNER FACIA PANEL
TO GAIN ACCESS TO THE 2 X TAP
SECURING SCREWS
UNDO BUNDY TUBE CONNECTION
AND REMOVE
DISCONNECT THERMOCOUPLE
REMOVE 2 GAS TAP SECURING
SCREWS AND REMOVE THE TAP
WHEN REPLACING TAP ALWAYS
ENSURE THAT A NEW TAP WASHER IS
FITTED (part number 081423974)
12
D) COOLING FANS
FOLLOW STEP 3 AND REMOVE THE
HOB TOP
REMOVE THE 4 X SECURING SCREWS
AS SHOWN AND REMOVE THE
COOLING FAN
E) THERMOSTATS
FOLLOW STEPS 3 AND 5 AND REMOVE THE HOB TOP
PULL THE THERMOSTAT FROM THE
BACK OF THE SWITCHPACK AND REMOVE THE PHIAL FROM THE
RELEVENT OVEN
13
F) TIMER
FOLLOW STEP 5 REMOVE FACIA
PANEL
RELEASE TIMER FROM HOLDING
CLIPS BY GENTLY PUSHING IN CLIPS
WITH A SCREWDRIVER
14
G) GRILL ELEMENT
FOLLOW STEP 6 AND REMOVE THE
REAR SERVICE PANEL
DISCONNECT WIRES
REMOVE GRILL ELEMENT GUARD BY
LOOSENING 2 HIDDEN SCREWS
(POSITIONS INDICATED ) AND
SLIDING OFF
REMOVE THE 2 SCREWS SECURING
THE ELEMENT BRACKET TO THE
CAVITY AND PULL THE ELEMENT
FORWARD TO REMOVE
15
H) LH OVEN FAN ELEMENT
FOLLOW STEP 6(AND REMOVE THE
REAR SERVICE PANEL
REMOVE 4 X REAR FAN COVER
SECURING SCREWS AND REMOVE
FAN COVER
DISCONNECT WIRING
REMOVE THE 2 ELEMENT SECURING
SCREWS AND PULL ELEMENT
FORWARD INTO THE CAVITY
16
I) LH OVEN STIR FAN
FOLLOW STEP 6(PAGE 6) AND REMOVE THE REAR SERVICE PANEL
REMOVE THE REAR FAN COVER AS
ON PREVIOUS PAGE
REMOVE THE FAN IMPELLOR
N.B L/H THREAD NEEDS TO TURNED
CLOCKWISE TO REMOVE
DISCONNECT WIRING FROM FAN
REMOVE 3 X STIR FAN SECURING
SCREWS AND REMOVE FAN FROM
THE REAR OF THE APPLIANCE
J) MAIN OVEN LIGHT FITTING
FOLLOW STEP 6 (PAGE 6) REMOVING
REAR SERVICE PANEL
REMOVE GLASS LAMP COVER BY
UNSCREWING
REMOVE THE EARTH LEAD
RELEASE 4 XCLIPS HOLDING LIGHT
FITTING IN PLACE
REMOVE BY PULLING LIGHT FITTING
FORWARD INTO CAVITY
17
K) RH OVEN STIR FAN AND ELEMENT
REMOVED AS PER L/H OVEN
L) R/H OVEN UPPER ELEMENT
REMOVE THE REAR SERVICE PANEL
DISCONNECT THE WIRING
REMOVE THE ELEMENT GUARD AS
PER GRILL ELEMENT REMOVAL
REMOVE THE 2X SECURING SCREWS
AND PULL AND REMOVE THE ELEMENT FROM THE CAVITY
M) R/H OVEN LOWER ELEMENT
FOLLOW STEP 6 AND REMOVE THE
REAR SERVICE PANEL
REMOVE REAR FAN COVER
REMOVE 3X SECURING SCREWS
FROM INSIDE THE CAVITY
WITHDRAW THE ELEMENT FROM THE
REAR
18
N) SLOW COOKER ELEMENT
FOLLOW STEP 6 AND REMOVE THE
REAR SERVICE PANEL
DISCONNECT THE WIRING
REMOVE THE 3 SCREWS FROM INSIDE THE CAVITY
REMOVE THE ELEMENT FROM THE
REAR
19
TECHNICAL SPECIFICATIONS
NOMINAL RESISTANCES AT 20oC
*5,//(/(0(17,11(5
287(5
Ÿ:
Ÿ
5+29(1/2:(5(/(0(17
Ÿ:
5+29(1723(/(0(17Ÿ:
5+29(1)$1(/(0(17
Ÿ:
/+29(1)$1(/(0(17Ÿ:
6/2:&22.(5(/(0(17Ÿ:
0$,129(167,5)$1
Ÿ
&22/,1*)$1
NŸ
THERMAL CUT-OUTS
TOP.......................
REAR...................
FAN RUN-ON.....
L120°C
L150°C
F60°C
20
BELLING
KENSINGTON
110DF
FAULTFINDING
GUIDES
Single Electric Cooker Main Fan oven not
working
Nothing working at all?
Is the Timer working?
No
Check fuse or
supply turned on
Yes
Is the clock set
to manual?
YES
Is there a neon on the facia?
Advise customer on
setting the timer
Yes
No
Is the neon on?
NO
Replace
Thermostat.
YES
NO
Does oven Stir fan run?
possible fault with
motor and switch.
YES
Does the oven heat
up?
Yes
Appliance working OK
NO
No
Fault with
element.
Electric Multi function oven Main oven not working
Nothing working at all?
No
Is the Timer working?
No
Check fuse or
supply turned on
Yes
Is the clock set
b
to manual?
YES
Has the customer selected
the correct function and set
the thermostat?
No
NO
Advise customer on how
to use oven functions.
Advise customer on
setting the timer
Yes
NO
Do any of the selected
functions work?
No
Possible fault with
Selector switch.
Yes
Does fan NO
oven work?
No
Which part of oven not
working? Fan or Element?
Replace
failed part
Yes
Does the Conventional
No
oven heat up?
No
Do either of the top or
bottom elements work?
Yes
Replace
failed part
Yes
No
Are ovens working OK, and only
certain functions not working?
Fault with the
selector switch
Yes
Diagnose faulty part and replace
i.e. Lamp assy or Top heat not
working,replace top element.
Gas Hob
Faulty ignition (Automatic ignition)
Customer states no ignition to burner/s
Is more than one
burner affected?
NO
Can You see a
spark at the burner?
YES
Are all four
burners affected
YES
YES
NO
NO
NO
check
electric supply to
hob?
Send engineer order
electrodes required and
Ignition switch (micro switch)
clean
and make sure burner
skirt and cap are fitted
correctly. If this does
not work.
YES
Replace spark
generator
Replace
electrode and ignition
switch ( micro switch)
Gas Hob
Faulty ignition (Push button ignition)
Customer states no ignition to burner/s
Is more than one
burner affected?
NO
Are all four
burners affected
YES
check
electric supply to
hob?
NO
NO
electrodes required and
possibly a spark generator
YES
Possible fault with ignition
switch and spark generator (these
could be combined as one so you
may just need the generator).
YES
Can customer see a
spark at the burner?
YES
NO
Replace electrode
clean
and make sure burner
skirt and cap are fitted
correctly. Did this
work?.
Gas hob with thermocouples
Hob burner will not stay lit
Burner won’t stay on when
control knob released
keep the control
knob depressed for 10 secs.
NO
YES
Advise customer control knob
must be kept depressed for at
least 10 secs
is the
thermocouple probe is in the
flame
YES
Replace
thermocouple and or gas tap.
NO
clean burner
skirt and cap also to make sure
they are correctly fitted.
Faulty ignition (Push button ignition)
Customer states no ignition to burner/s
Is more than one
burner affected?
NO
Are all four
burners affected
YES
check
electric supply to
hob?
YES
Can you see a
spark at the burner?
YES
NO
NO
Replace
electrodes as required and
possibly a spark generator
YES
NO
Replace ignition switch
and or spark generator
Replace the electrode
clean
and make sure burner
skirt and cap are fitted
correctly. Did this
work?.
Faulty ignition (Automatic ignition)
Customer states no ignition to burner/s
Is more than one
burner affected?
NO
Can you see a
spark at the burner?
YES
Are all four
burners affected
YES
YES
NO
NO
NO
check
electric supply to
hob?
Replace
electrodes as required and
Ignition switch (micro switch)
clean
and make sure burner
skirt and cap are fitted
correctly. If this does
not work.
YES
Replace spark
generator
Replace
electrode and or ignition
switch ( micro switch)
Download PDF

advertising