Subzero-10 manual

SUBZERO-10
1500 WATTS
1” = 2.54 cm
1 cubic foot = 1728 cubic inches
Grille Clearance: 2”
Displacement:
Winner of the 2004
Design & Engineering Award
INNOVATIONS
INTERNATIONAL CES
#1
Sealed design for tight bass
#2
Port tuned design for deep bass
#3
Ported design
16"
12"
11"
11”
15"
15 1/2"
#2
11"
12"
#1
4"
diameter
12"
SUBZERO-10"
Outer dimension shown using 3/4" thick MDF
Total outer box volume = 0.91 cubic foot.
Sealed design for tight bass
SUBZERO-10"
12"
Port
Outer dimension shown using 3/4" thick MDF.
Total outer box volume = 1.22 cubic feet.
SUBZERO-10"
PORT (2"x10.5"x11")
Internal dimensions
8 1/2" long
Outer dimension shown using 3/4" thick MDF
Total outer box volume = 1.61 cubic feet.
SUBZERO-10
Cut out hole 235mm / 9 1/4”
23 1/2”
15”
12”
SUBZERO-10"
Mounting
depth
220mm
6 1/2”
SUBZERO-10"
18 1/2”
Outer dimension shown using 3/4" thick MDF
Total outer box volume = 2.73 / 1.36 per sub
Specifications are subject to change without notice
HANDCRAFTED IN USA.
HOW TO WIRE / FUSE YOUR
SUBZERO TO AN AMPLIFIER
2-channel
2 x 4-ohm load
(voice coils separated)
(no fuses)
VC #2
VC #2
VC #1
VC #2
VC #1
VC #1
P
P
P
S
1+ 2+
DO NOT
USE
MONO 2-OHMS
1
-
CH-1
2
-
1+ 2+
CH-2
TYPICAL AMPLIFIER TERMINAL
TYPICAL AMPLIFIER TERMINAL
The diagram -on the left side- shows
the PSP terminal in a 2-ohm parallel
configuration (both voice coils are
connected in parallel). Simply place
the 2 fuses in the outer positions in
the fuse placement area. Insert the
negative speaker wire to the far left
insert and one positive to the far right
insert.
This diagram shows the PSP terminal
in a 4-ohm configuration (the two
voice coils are separated). No fuses
are used in this configuration,the voice
coils are powered up separately.
1
-
8-GAUGE
-
P
S
8-GAUGE
2
8-GAUGE
8-GAUGE
-
8-GAUGE
1
P
S
3mm
Hex-nut
cable
fasteners
8-GAUGE
P
1-channel
8-ohm load
(voice coils in series)
(1 fuse)
2
-
1+ 2+
DO NOT
USE
8-GAUGE
2-channel
2-ohm load
(voice coils in parallel)
(using 2 fuses)
8-GAUGE
The Subzero subwoofer
comes equipped with 2
voice coils (dual 2x4
ohms), it can be used in
2, 4 and 8ohm
configurations. The
terminal comes equipped
with fused jumpers, the
voice coil can be easily
configured in series or in
parallel to match the
amplifier in use. It is just a
simple flip of a fuse,
here’s how it works.
PSP (Parallel Series Parallel) Terminal
MONO 8-OHMS
TYPICAL AMPLIFIER TERMINAL
The diagram - on the right side-displays
the PSP in an 8-ohm mode. You will
notice that there is only one fuse in
the center of the fuse placement area.
The voice coils are wired in series.
Insert the negative speaker wire to the
far left insert and one positive to the
far right insert.
Electro Mechanical Parameters
Name = Subzero 10 (broken in)
Xmax = 31.7500E-3 M
Note = VI MEASURMENTS
Krm = 52.9380E-3 Ohm
Model = TSL
Erm = 667.0000E-3
Domain = FreeAir
Kxm = 78.4200E-3 H
Shape = Round
Exm = 685.0000E-3
Profile = Cone
Rms =19.3984 N·S/M
Fmd = 3.0000 KA
Mms = 155.7620 g
Qmd = 1.0000
Cms =197.1628 uM/N
Flp = 8.0000 KA
Vas = 1.0830 Ft³
Qlp = 2.0000
Fo = 28.7195 Hz
Znom = 8.0000 Ohm
Qms = 1.4489
Revc = 7.7000 Ohm
Qes = 0.6994
Sd = 33.0000 msqM
Qts = 0.4717
Mmd = 152.3169 g
BL = 17.5913 T·M
Pmax = 1.0000E3 W
Levc = 4.9888 mH
Rtvc = 250.0000E-3 °C/W
SPLo = 82 dB
Xgap = 500.0000E-3 In
No = 0.0995821%
Xcoil = 3.0000 In