Venmar Constructo 1.5ES, 2.0ES, Solo 1.5ES, 2.0ES HRV, Constructo 2.0ES ERV Installer Manual

INSTALLER MANUAL
VB0175
VB0176
HRV CONSTRUCTO 1.5ES*
HRV SOLO 1.5ES*
(PART NOS 46110 AND 1601702)
(PART NOS 46720 AND 46725)
HRV CONSTRUCTO 2.0ES*
HRV SOLO 2.0ES*
(PART NO. 47110)
(PART NO. 47720)
* THESE PRODUCTS EARNED THE ENERGY STAR® BY MEETING STRICT ENERGY EFFICIENCY GUIDELINES SET BY
NATURAL RESOURCES CANADA AND THE US EPA. THEY MEET ENERGY STAR REQUIREMENTS ONLY WHEN
USED IN CANADA.
ERV CONSTRUCTO 2.0ES
(PART NO. 47115)
IMPORTANT
INFORMATION FOR THIS UNIT ABOUT DRAIN
INSTALLATION IN COLD CLIMATES ON PAGE
12, SECTION 3.8.
VB0170
RESIDENTIAL USE ONLY
READ AND SAVE THESE INSTRUCTIONS
20503 REV. 03
ABOUT THIS MANUAL
Because of the large amount of models covered by this publication, the illustrations are typical ones. Some details of your unit may be
slightly different than the ones shown.
Please take note that this manual uses the following symbols to emphasize particular information:
! WARNING
Identifies an instruction which, if not followed, might cause serious personal injuries including possibility of death.
CAUTION
Denotes an instruction which, if not followed, may severely damage the unit and/or its components.
NOTE: Indicates supplementary information needed to fully complete an instruction.
We welcome any suggestions you may have concerning this manual and/or the unit, and we would appreciate hearing your comments
on ways to better serve you. Please contact us by phone at 1-800-567-3855.
ABOUT THESE UNITS
LIMITATION
For residential (domestic) installation only. These units must be installed in accordance with all national and local regulations, building
codes and safety codes.
! WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSON(S) OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or
telephone number listed in the warranty.
2. Before servicing or cleaning this unit, disconnect power cord from electrical outlet.
3. This unit is not designed to provide combustion and/or dilution air for fuel-burning appliances.
4. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
5. Do not use this unit with any solid-state speed control device other than following:
Units
Optional Main Controls
Optional Auxiliary Controls
Constructo
Deco-Touch, Lite-Touch Constructo, Constructo
Dehumidistat, 20-min. lighted push-button,
60-min. mechanical timer
Solo
Altitude, Deco-Touch, Lite-Touch Constructo,
Simple-Touch Constructo, Constructo
Dehumidistat, 20/40/60-min. lighted push-button,
60-min. mechanical timer
6. This unit must be grounded. The power supply cord has a 3-prong grounding plug for your personal safety. It must be plugged into a
mating 3-prong grounding receptacle, grounded in accordance with the national electrical code and local codes and ordinances. Do
not remove the ground prong. Do not use an extension cord.
7. Do not install in a cooking area or connect directly to any appliances.
8. Do not use to exhaust hazardous or explosive materials and vapors.
9. When performing installation, servicing or cleaning this unit, it is recommended to wear safety glasses and gloves.
10. Due to the weight of the unit, two installers are recommended to perform installation.
11. When applicable local regulation comprise more restrictive installation and/or certification requirements, the aforementioned
requirements prevail on those of this document and the installer agrees to conform to these at his own expenses.
CAUTION
1.
2.
3.
4.
5.
6.
7.
8.
To avoid prematurate clogged filters, turn OFF the unit during construction or renovation.
Please read specification label on product for further information and requirements.
Be sure to duct air outside – Do not intake/exhaust air into spaces within walls or ceiling or into attics, crawl spaces, or garage.
Intended for residential installation only in accordance with the requirements of NFPA 90B (for a unit installed in U.S.A.) or Part 9 of
the National Building Code of Canada (for a unit installed in Canada).
Do not run any air ducts directly above or closer than 2 ft (0.61 m) to any furnace or its supply plenum, boiler, or other heat producing
appliance. If a duct has to be connected to the furnace return plenum, it must be connected not closer than 9’ 10” (3 m) from this
plenum connection to the furnace.
The ductwork is intended to be installed in compliance with all local and national codes that are applicable.
When leaving the house for a long period of time (more than two weeks), a responsible person should regularly check if the unit
operates adequately.
If the ductwork passes through an unconditioned space (e.g.: attic), the unit must operate continuously except when performing
maintenance and/or repair. Also, the ambient temperature of the house should never drop below 18°C (65°F).
2
TABLE OF CONTENTS
1. TECHNICAL DATA ..................................................................................................................................... 4-5
1.1
1.2
1.3
1.4
AIR DISTRIBUTION (NORMAL OPERATION) ............................................................................................................................ 4
AIR DISTRIBUTION (DEFROST MODE) .................................................................................................................................. 4
DEFROST CYCLES TABLES................................................................................................................................................. 4
DIMENSIONS .................................................................................................................................................................. 5
1.41 HRV CONSTRUCTO 1.5ES, HRV CONSTRUCTO 2.0ES, HRV SOLO 1.5ES AND HRV SOLO 2.0ES .................................................. 5
1.4.2 ERV CONSTRUCTO 2.0ES ....................................................................................................................................................... 5
1.5 SPECIFICATIONS ............................................................................................................................................................. 5
2. TYPICAL INSTALLATIONS ........................................................................................................................... 6
2.1 FULLY DUCTED SYSTEM ................................................................................................................................................... 6
2.2 EXHAUST DUCTED SYSTEM (SOURCE POINT VENTILATION) ...................................................................................................... 6
2.3 SIMPLIFIED (VOLUME VENTILATION) .................................................................................................................................... 6
3. INSTALLATION ......................................................................................................................................... 7-13
3.1
3.2
3.3
3.4
INSPECT THE CONTENT OF THE BOX ................................................................................................................................... 7
LOCATING AND MOUNTING THE UNIT .................................................................................................................................. 7
PLANNING OF THE DUCTWORK .......................................................................................................................................... 7
CALCULATING THE DUCT SIZE ............................................................................................................................................ 8
3.4.1 EXAMPLE OF CALCULATION ......................................................................................................................................................... 8
3.4.2 EXAMPLE OF A DESIGN FOR A FULLY DUCTED SYSTEM ...................................................................................................................... 8
3.5 INSTALLING THE DUCTWORK AND THE REGISTERS ............................................................................................................. 9-10
3.5.1 FULLY DUCTED SYSTEM .............................................................................................................................................................. 9
3.5.2 EXHAUST DUCTED SYSTEM ......................................................................................................................................................... 9
3.5.3 SIMPLIFIED INSTALLATION ..........................................................................................................................................................10
3.6 CONNECTING THE DUCTS TO THE UNIT ............................................................................................................................. 11
3.7 INSTALLING THE EXTERIOR HOODS ................................................................................................................................... 12
3.8 CONNECTING THE DRAIN .......................................................................................................................................... 12-13
3.8.1 HRV UNITS ...........................................................................................................................................................................12
3.8.2 ERV UNIT .............................................................................................................................................................................13
4. CONTROLS ............................................................................................................................................13-15
4.1 INTEGRATED CONTROL .................................................................................................................................................. 13
4.1.1 BOOT SEQUENCE ....................................................................................................................................................................13
4.1.2 SETTING EXTENDED DEFROST ....................................................................................................................................................13
4.2 ELECTRICAL CONNECTION TO OPTIONAL WALL CONTROLS ................................................................................................ 14-15
4.2.1 ELECTRICAL CONNECTION TO ALTITUDE MAIN WALL CONTROL ............................................................................................................14
4.2.2 ELECTRICAL CONNECTION TO DECO-TOUCH MAIN WALL CONTROL......................................................................................................14
4.2.3 ELECTRICAL CONNECTION TO LITE-TOUCH CONSTRUCTO OR SIMPLE-TOUCH CONSTRUCTO MAIN WALL CONTROL.......................................15
4.2.4 ELECTRICAL CONNECTION TO CONSTRUCTO MAIN WALL CONTROL .....................................................................................................15
4.2.5 ELECTRICAL CONNECTION TO OPTIONAL AUXILIARY WALL CONTROLS ...................................................................................................15
5. ELECTRIC CONNECTION TO THE FURNACE ..........................................................................................15
6. WIRING DIAGRAM .......................................................................................................................................16
7. BALANCING THE UNIT ...............................................................................................................................17
7.1
7.2
7.3
WHAT YOU NEED TO BALANCE THE UNIT ......................................................................................................................... 17
PRELIMINARY STAGES TO BALANCE THE UNIT ................................................................................................................... 17
BALANCING PROCEDURE ............................................................................................................................................. 17
8. SERVICE PARTS .........................................................................................................................................18
9. TROUBLESHOOTING ........................................................................................................................... 19-20
3
1. TECHNICAL DATA
1.1 AIR DISTRIBUTION (NORMAL OPERATION)
1.2 AIR DISTRIBUTION (DEFROST MODE)
VF0053
VF0052
1.3 DEFROST CYCLES TABLES
HRV CONSTRUCTO 1.5ES AND SOLO 1.5ES UNITS
OUTSIDE TEMPERATURE
DEFROST CYCLES (MINUTES)
CELCIUS (°C)
FAHRENHEIT (°F)
DEFROSTING
-5
23
7
OPERATION TIME BETWEEN EACH
DEFROST CYCLES
50
EXTENDED DEFROST CYCLES
DEFROSTING
OPERATION TIME BETWEEN EACH
DEFROST CYCLES
10
30
-15
5
7
25
10
20
-27
-17
10
20
10
15
ERV CONSTRUCTO 1.5 ES UNIT
OUTSIDE TEMPERATURE
DEFROST CYCLES (MINUTES)
OPERATION TIME BETWEEN EACH
EXTENDED DEFROST CYCLES
FAHRENHEIT (°F)
DEFROSTING
-5
23
10
60
10
30
-15
5
10
30
10
20
-27
-17
10
20
10
15
DEFROST CYCLES
DEFROSTING
OPERATION TIME BETWEEN EACH
CELCIUS (°C)
DEFROST CYCLES
HRV CONSTRUCTO 2.0ES AND SOLO 2.0ES UNITS
OUTSIDE TEMPERATURE
DEFROST CYCLES (MINUTES)
CELCIUS (°C)
FAHRENHEIT (°F)
DEFROSTING
OPERATION TIME BETWEEN EACH
DEFROST CYCLES
EXTENDED DEFROST CYCLES
DEFROSTING
OPERATION TIME BETWEEN EACH
DEFROST CYCLES
-5
23
6
50
10
30
-15
5
6
25
10
20
-27
-17
10
20
10
15
NOTE: The Constructo and Solo Performance Charts are listed on the specification sheets of these units.
Visit our website at www.venmar.ca to access those documents.
4
1. TECHNICAL DATA (CONT’D)
1.4 DIMENSIONS
1.4.1 HRV CONSTRUCTO 1.5ES, HRV CONSTRUCTO 2.0ES, HRV SOLO 1.5ES AND HRV SOLO 2.0ES
35” (891 mm)
Hooks Location
for Hanging Chains
17¼” (438 mm)
30¼” (768 mm)
Motorized
Damper
Terminal
Block
Location
17”
(432 mm)
Heat
Recovery
Core
Door
Power Cord
36” (914 mm)
VK0077A
6”
(152 mm)
Blower
Assembly
1.4.2 ERV CONSTRUCTO 2.0ES
39” (991 mm)
Hooks Location
for Hanging Chains
17¼” (438 mm)
34” (864 mm)
Motorized
Damper
Terminal
Block
Location
17”
(432 mm)
Energy
Recovery
Core
Door
VK0078A
Power Cord
36” (914 mm)
6”
(152 mm)
Blower
Assembly
1.5 SPECIFICATIONS
MODEL
HRV CONSTRUCTO 1.5ES
HRV CONSTRUCTO 2.0ES
WEIGHT
65 LB (29.5 kg)
65 LB (29.5 kg)
76 (34.5 KG)
65 LB (29.5 kg)
65 LB (29.5 kg)
6˝ (152 MM)
6˝ (152 MM)
6˝ (152 MM)
6˝ (152 MM)
6˝ (152 MM)
1/2˝ (12 MM)
1/2˝ (12 MM)
1/2˝ (12 MM)
1/2˝ (12 MM)
1/2˝ (12 MM)
PORT
DIAMETER
DRAIN
DIAMETER
ERV CONSTRUCTO 2.0ES
HRV SOLO 1.5ES
INSTALLATION
CHAINS AND SPRINGS (PROVIDED WITH THE UNIT)
MOTOR
SPEED
HIGH AND LOW SPEED FACTORY SET (OPTIONAL INCREASED LOW SPEED)
HRV SOLO 2.0ES
ELECTRICAL
SUPPLY
120 V, 60 HZ
120 V, 60 HZ
120 V, 60 HZ
120 V, 60 HZ
120 V, 60 HZ
POWER
CONSUMPTION
160 WATTS
195 WATTS
200 WATTS
160 WATTS
195 WATTS
5
2. TYPICAL INSTALLATIONS
NOTE: Installation may vary according to the model number and the position; normal or reverse (Solo units only) in wich the unit is installed.
There are three common installation methods.
2.1 FULLY DUCTED SYSTEM
(Primarily for homes with radiant hot water or electric baseboard heating.
See illustration at right.)
Moist, stale air is exhausted from the high humidity areas in the home, such as
bathrooms, kitchen and laundry room.
Fresh air is supplied to bedrooms and principal living areas.
If required, bathroom fans and a range hood may be used to better exhaust
stale air.
Homes with more than one level require at least one exhaust register at the
highest level.
See 3.5.1 for details
VH0077
2.2 EXHAUST DUCTED SYSTEM (SOURCE POINT VENTILATION)
(For homes with forced air heating. See illustration at right.)
Moist, stale air is exhausted from the high humidity areas in the home, such as
bathrooms, kitchen and laundry room. Fresh air is supplied to the cold air return
or the supply duct of the furnace. If required, bathroom fans and a range hood
may be used to better exhaust stale air.
Homes with more than one level require at least one exhaust register at the
highest level.
NOTE: For this type of installation, it is not essential that the furnace blower
runs when the unit is in operation, but we recommend it.
See 3.5.2 for details
VH0078
2.3 SIMPLIFIED (VOLUME VENTILATION)
(For homes with forced air heating. See illustration at right.)
Fresh air and exhaust air flow through the furnace ducts, which simplifies the
installation.
The use of bathroom fans and a range hood is suggested to exhaust stale air.
NOTE: For this type of installation, the furnace blower must be running
when the unit is in operation.
VH0079
6
See 3.5.3 for details
3. INSTALLATION
! WARNING
When applicable local regulation comprises more restrictive installation and/or certification requirements, the
aforementioned requirements prevail on those of this document and the installer agrees to conform to these at
his own expenses.
! WARNING
When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.
3.1 INSPECT THE CONTENT OF THE BOX
• Inspect the exterior of the unit for shipping damage. Ensure that there is no damage to the door, door latches, door hinges, dampers,
duct collars, cabinet, etc.
• Inspect the interior of the unit for damage. Ensure that the fan motor assembly, recovery module, insulation, dampers, condensation tray
are all intact.
• If the unit was damaged during shipping, contact your local distributor. (Claim must be made within 24 hours after delivery.)
WING NUT
SHIPPING BRACKET
NOTE: Prior to install the unit, remove its shipping bracket by unscrewing its wing nut and loosing
its both retaining screws.
RETAINING SCREWS
VD0283
3.2 LOCATING AND MOUNTING THE UNIT
NOTE: Please note that Solo units can be installed in either the normal or reverse (upside down) position.
CAUTION
For Solo units only, when installed in reverse postion (upside down) in a cold region where outside temperature
could drop below -20oC (-4oF) for more than 5 days in a row, the unit must always be set in extended defrost. See
Section 4.1.2 Setting Extended Defrost.
Choose an appropriate location for the unit:
• Within an area of the house where the ambient temperature is kept between 10°C (50°F) and 40°C (104°F)
• Away from living areas (dining room, living room, bedroom), if possible
• So as to provide easy access to the interior cabinet for every three months and annual maintenance, and
to the control panel on the side of the unit;
• Close to an exterior wall, so as to limit the length of the insulated flexible duct to and from the unit
• Close to a drain. If no drain is close by, use a pail to collect run-off
VD0037
• Away from hot chimneys, electrical panel and other fire hazards
• Allow for a power source (standard outlet)
Hang the unit with the 4 chains and springs provided (see illustrations at right).
VD0279
3.3 PLANNING OF THE DUCTWORK
a) Follow the instructions in Section 3.4 (next page) to determine the appropriate duct diameters for your system.
b) Keep it simple. Plan for a minimum number of bends and joints. Keep the length of insulated duct to a minimum.
c) Do not use wall cavities as ducts. Do not use branch lines smaller than 4” Ø (102 mm Ø).
d) Do not ventilate crawl spaces or cold rooms. Do not attempt to recover the exhaust air from a dryer or a range hood. This would cause
clogging of the recovery module. Use sheet metal for the kitchen exhaust duct.
e) Be sure to plan for at least one exhaust register on the highest lived-in level of the house if it has 2 floors or more.
7
3. INSTALLATION (CONT’D)
3.4 CALCULATING THE DUCT SIZE
Use the table below to ensure that the ducts you intend to install will be carrying air flows at or under the recommended values.
Avoid installing ducts that will have to carry air flows near the maximum values and never install a duct if its air flow exceeds
the maximum value.
DUCT
DIAMETER
RECOMMENDED AIR FLOW
MAXIMUM AIR FLOW
4˝ (102 MM)
40 CFM
19 L/S
68 M3/H
60 CFM
28 L/S
102 M3/H
5˝ (127 MM)
75 CFM
35 L/S
127 M3/H
110 CFM
52 L/S
187 M3/H
6˝ (152 MM)
120 CFM
57 L/S
204 M3/H
180 CFM
85 L/S
306 M3/H
7˝ (178 MM)
185 CFM
87L/S
314 M3/H
270 CFM
127 L/S
459 M3/H
8˝ (203 MM)
260 CFM
123 L/S
442 M3/H
380 CFM
179 L/S
645 M3/H
NOTE: Examples 3.4.1 and 3.4.2 use imperial measures.
The same calculation applies to metric measures.
3.4.1 EXAMPLE OF CALCULATION
PROBLEM: My installation requires two exhaust registers (one for the kitchen, one for the bathroom).
END
I will connect these registers to a main duct which will connect to the unit (high speed performance BRANCHES
value of 140 cfm). What size of duct should I use for the main exhaust duct and for the two end
5˝ø
branches leading to the registers? (See illustration at right.)
70 CFM
SOLUTION: Simplified method. (For a more detailed method of calculating duct size refer to the ASHRAE
or HRAI HANDBOOK).
Main duct: Table above indicates a 6” Ø duct: Recommended air flow: 120 cfm; maximum air flow:
180 cfm. The high speed air flow of 140 cfm is close enough to the recommended value (120) and
far enough away from the maximum value (180). Therefore a 6” Ø duct or larger is an appropriate
choice for the main exhaust duct.
VI0003
End branches: Each end branch will have to transport an air flow of 70 cfm (140 divided by 2).
Table above indicates a 5” Ø duct: Recommended air flow: 75 cfm; maximum air flow: 110 cfm. The
high speed air flow of 70 cfm is close enough to the recommended value (75) and far enough away
from the maximum value (110). Therefore a 5” Ø duct or larger is an appropriate choice for the 2
end branches.
NOTE: A 4” Ø duct would have been too small because the maximum acceptable value for a 4” Ø
duct is 60 cfm.
3.4.2 EXAMPLE OF A DESIGN FOR A FULLY DICTED SYSTEM FOR A UNIT HAVING A HIGH SPEED PERFORMANCE OF 222 CFM
5˝
5˝
4˝
4˝
5˝ø
64 CFM
4˝ø
42 CFM
4˝ø
42 CFM
5˝ø
65 CFM
4˝ø
42 CFM
4˝
6˝
6˝ø
129 CFM
6˝ø
93 CFM
VI0004
6˝ø
84 CFM
6˝
7˝
4˝
4˝
7˝ø
222 CFM
8
6˝
6˝
7˝
7˝ø
222 CFM
6˝ø
96 CFM
6˝ø
138 CFM
MAIN BRANCH
6˝ø 140 CFM
3. INSTALLATION (CONT’D)
3.5 INSTALLING THE DUCTWORK AND THE REGISTERS
! WARNING
Never install a stale air exhaust register in a room where there is a combustion device, such as a gas furnace, a
gas water heater or a fireplace.
CAUTION
The ductwork is intended to be installed in compliance with all local and national codes that are applicable.
3.5.1 FULLY DUCTED SYSTEM (AS ILLUSTRATED IN SECTION 2.1)
STALE AIR EXHAUST DUCTWORK:
• Install registers in areas where contaminants are produced: Kitchen, bathrooms, laundry room, etc.
• Install registers 6 to 12 inches (152 to 305 mm) from the ceiling on an interior wall OR install them in the ceiling.
• Install the kitchen register at least 4 feet (1.2 m) from the range.
• If possible, measure the velocity of the air flowing through the registers. If the velocity is higher than 400 ft/min. (122 m/min), then
the register type is too small. Replace with a larger one.
FRESH AIR DISTRIBUTION DUCTWORK:
• Install registers in bedrooms, dining room, living room and basement.
• Install registers either in the ceiling or high on the walls with air flow directed towards the ceiling.
(The cooler air will then cross the upper part of the room, and mix with room air before descending to occupant level.)
• If a register must be floor installed, direct the air flow up the wall.
3.5.2 EXHAUST DUCTED SYSTEM (AS ILLUSTRATED IN SECTION 2.2)
STALE AIR EXHAUST DUCTWORK:
Same as for Fully Ducted System, described on point 3.5.1 above)
FRESH AIR DISTRIBUTION:
! WARNING
When performing duct connection to the furnace, installation must be done in accordance with all applicable
codes and standards. Please refer to your local building code.
CAUTION
When performing duct connection to the furnace supply duct, this duct must be sized to support the additional
airflow produced by the ERV/HRV. Also, use a metal duct. It is recommended that the ERV/HRV is running when the
furnace is in operation in order to prevent backdrafting inside ERV/HRV.
There are two methods for connecting the unit to the furnace:
METHOD 1: SUPPLY SIDE CONNECTION
• Cut an opening into the furnace supply duct at least 18 inches (0.5 m)
from the furnace.
• Connect this opening to the fresh air distribution port of the HRV/ERV
(use metal duct, see illustration at right).
• Make sure that the HRV/ERV duct forms an elbow inside the furnace ductwork.
• If desired, interlock (synchronize) the furnace blower operation with
the HRV/ERV operation. (See Section 5).
MINIMUM
18’’ (0.5 M)
METAL DUCT
VJ0084
METHOD 2: RETURN SIDE CONNECTION
A
• Cut an opening into the furnace return duct not less than 10 feet (3.1 m)
from the furnace (A+B).
• Connect this opening to the fresh air distribution port of the HRV/ERV
(see illustration at right).
NOTE: For Method 2, it is not essential that the furnace blower runs when the unit is
in operation, but we recommend it. If desired, synchronize the furnace blower
operation with the HRV/ERV operation. (See Section 5).
9
B
VJ0085
A+B= NOT LESS
THAN 10’ (3.1 M)
3. INSTALLATION (CONT’D)
3.5 INSTALLING THE DUCTWORK AND THE REGISTERS (CONT’D)
3.5.3 SIMPLIFIED INSTALLATION (AS ILLUSTRATED IN SECTION 2.3)
! WARNING
When performing duct connection to the furnace, installation must be done in accordance with all applicable
codes and standards. Please refer to your local building code.
CAUTION
When performing duct connection to the furnace ducts (Method 1), these ducts must be sized to support the
additional airflow produced by the ERV/HRV. Also, the supply duct must be a metal duct. It is recommended that
the ERV/HRV is running when the furnace is in operation in order to prevent backdrafting inside ERV/HRV.
There are two methods (illustrated below) for connecting the unit to the furnace ducts:
METHOD 1: RETURN-SUPPLY
METHOD 2: RETURN-RETURN
MINIMUM
18’’ (0.5 M)
A
METAL DUCT
B
A
MINIMUM
3’ (0.9 M)
B
VJ0087
A+B= NOT LESS
10’ (3.1 M)
THAN
A+B= NOT LESS
THAN 10’ (3.1 M)
VJ0086
STALE AIR INTAKE:
• Cut an opening into the furnace return duct not less than 10 feet (3.1 m) from the furnace.
• Connect this opening to the stale air intake port of the HRV/ERV (as shown above).
FRESH AIR DISTRIBUTION:
Same instructions as for Method 1 or Method 2, section 3.5.2 in previous page)
CAUTION
If using Method 2, make sure the furnace blower operation is synchronized with the unit operation! See Section 5.
For Method 2 (Return-Return), make sure there is a distance of at least 3 feet (0.9 m) between the 2 connections to the furnace
duct.
NOTE: For Method 1, it is not essential to synchronize the furnace blower operation with the HRV/ERV operation, but we
recommend it.
10
3. INSTALLATION (CONT’D)
3.6 CONNECTING THE DUCTS TO THE UNIT
CAUTION
If ducts have to go through an unconditioned space (e.g.: attic), always use insulated ducts.
INSULATED FLEXIBLE DUCTS
Use the following procedure for connecting the insulated flexible duct to the ports on the unit (exhaust to outside and fresh air from
outside).
 Pull back the insulation to expose the flexible duct.
 Attach the flexible duct to the port using tie wrap.
 Pull the insulation over the joint and tuck it between the inner and outer rings of the double collar.
 Pull down the vapor barrier (shaded part in illustrations below) over the outer ring to cover it completely. Fasten in place the vapor
barrier using the port strap (included in unit parts bag). To do so, insert one collar pin through vapor barrier and first strap hole,
then insert the other collar pin through vapor barrier and center strap hole and close the loop by inserting the first collar pin in the
last strap hole.
CAUTION
Make sure the vapor barrier on the insulated ducts does not tear during installation to avoid condensation within
the ducts.
COLLAR PIN
1
2
3
4
COLLAR PIN
VJ0083
RIGID DUCTS
Use duct tape to connect the rigid ducts to the ports.
CAUTION
Do not use screws to connect rigid ducts to the ports.
Make sure that both balancing dampers are left in a fully open
position before connecting the ducts to these ports (Fresh air to
building port and Exhaust air from building port as shown on
illustration at right).
VJ0088
11
3. INSTALLATION (CONT’D)
3.7 INSTALLING THE EXTERIOR HOODS
Choose an appropriate location for installing the exterior hoods:
6” ø
(152 MM)
EXHAUST
HOOD
• At a minimum distance of 6 feet (1.8 m) between the hoods to
avoid cross-contamination
INTAKE
HOOD
• At a minimum distance of 18 inches (457 mm) from the ground
18”
(457 MM)
6’
(1.8 M)
! WARNING
Make sure the intake hood is at least 6 feet (1.8 m) away
from any of the following:
• Dryer exhaust, high efficiency furnace vent,
central vacuum vent
• Gas meter exhaust, gas barbecue-grill
• Any exhaust from a combustion source
• Garbage bin and any other source of contamination
18”
(457 MM)
6’
(1.8 M)
OPTIONAL
TAPE AND DUCT TIE
18”
(457 MM)
DUCT LOCATION
CAULKING
Refer to illustration at right for connecting the insulated duct to the
hoods. An “Anti-Gust Intake Hood” should be installed in regions
where a lot of snow is expected to fall.
VD0028
3.8 CONNECTING THE DRAIN
CAUTION
A drain tubing (included) must be installed for all HRV units. For ERV units, it is not required, however, it is
recommended for climates where the outside temperature typically remains below -25°C (-13°F), (over a 24-hour
period) for several days in a row, combined with an indoor humidity of 40% or higher.
3.8.1 HRV UNITS
8" MIN.
± 12"
(± 305 mm)
± 12"
(± 305 mm)
8" MAX.
VD0282
± 1"
VO0232A
Cut 2 sections of the plastic tube, about
VO0231A
12” (305 mm) long, and attach them to each
inner drain fitting, located under the unit.
Make a water trap loop in the tube to prevent
Join both short sections to the “T” junction the unit from drawing unpleasant odors
and main tube as shown.
from the drain source. Make sure this loop
is located UNDER the “T” as shown. Run
the tube to the floor drain or to an alternative
drain pipe or pail.
IMPORTANT: If using a pail to collect water,
locate the tube end approximately 1” from
the top of the pail in order to prevent water
from being drawn back up into the unit.
12
SOLO UNITS ONLY
Insert both drain plugs (included in parts
bag) in alternate drain fittings located on top
of the unit.
3. INSTALLATION (CONT’D)
3.8 CONNECTING THE DRAIN (CONT’D)
3.8.2 ERV UNIT
8" MIN.
8" MAX.
VD0287
± 1"
Insert a drain plug (included in parts bag) in
alternate drain fitting located on top of the
unit.
VO0243A
Make a water trap loop in the tube to prevent the unit from drawing unpleasant odors from
the drain source. Run the tube to the floor drain or to an alternative drain pipe or pail.
IMPORTANT: If using a pail to collect water, locate the tube end approximately 1” from
the top of the pail in order to prevent water from being drawn back up into the unit.
Furthermore, if the drain will not be used,
insert a second drain plug (included in
parts bag) in the drain fitting located
underneath the unit.
4. CONTROLS
4.1 INTEGRATED CONTROL
All units are equipped with an integrated control, located in front of the electrical compartment. Use the
push button (1) to control the unit. The LED (2) will then show on which mode the unit is in.
NOTES: 1. The integrated control must be turned OFF to use an optional main control.
2. If an optional auxiliary control is used, if activated, this auxiliary control will override the
optional main control.
Refer to table below to see how to operate the unit using its integrated control.
PRESS ON PUSH BUTTON
LED COLOR
RESULTS
ONCE
AMBER
UNIT IS ON LOW SPEED
TWICE
GREEN
UNIT IS ON HIGH SPEED
THREE TIMES
NO LIGHT
UNIT IS OFF
2
1
VD0278
If a problem occurs during the unit operation, its integrated control LED (2) will blink. The color of the blinking light depends on the
type of error detected. Refer to Section 9 Troubleshooting on pages 19 and 20 for further details.
4.1.1 BOOT SEQUENCE
The unit boot sequence is similar to a personnal computer boot sequence. Each time the unit is plugged after being unplugged, or
after a power failure, the unit will perform a 30-second booting sequence before starting to operate. During the booting sequence,
the integrated control LED will light GREEN (unit set in normal defrost) or AMBER (unit set in extended defrost) for 5 seconds, and
then will shut off for 2 seconds. After that, the LED will light RED for the rest of the booting sequence. During this RED light phase,
the unit is checking and resetting the motorized damper position. Once the motorized damper position completely set, the RED
light turns off and the booting sequence is done.
NOTE: No command will be taken until the unit is fully booted.
4.1.2 SETTING EXTENDED DEFROST
The unit is factory set to normal defrost. In cold region, it may be necessary to setup extended defrost. During
the first 5 seconds of booting sequence, while the integrated control LED is GREEN, press on push button until
the LED turns AMBER (about 3 seconds).
VD0281
CAUTION
For Solo units only, when installed in reverse postion (upside down) in a cold region where outside temperature
could drop below -20oC (-4oF) for more than 5 days in a row, the unit must always be set in extended defrost.
13
4. CONTROLS (CONT’D)
4.2 ELECTRICAL CONNECTION TO OPTIONAL WALL CONTROL
For more convenience, this unit can also be controlled using an optional main wall control.
! WARNING
Always disconnect the unit before making any connections. Failure in disconnecting power could result in electrical
shock or damage of the wall control or electronic module inside the unit.
CAUTION
Never install more than one optional main wall control per unit. Make sure that the wires do not short-circuit
between themselves or by touching any other components on the wall control. Avoid poor wiring connections. To
reduce electrical interference (noise) potential, do not run wall control wiring next to control contactors or near
light dimming circuits, electrical motors, dwelling/building power or lighting wiring, or power distribution panel.
Use the terminal connector included in the installation kit to perform the electrical
connection for main and optional wall controls. Check if all wires are correctly inserted
in their corresponding holes in the terminal block. (A wire is correctly inserted when its
orange receptacle is lower than another one without wire. On picture at right, wire A is
correctly inserted, but not wire B.)
A
B
VE0106
Once the wall control(s) connections have been made, insert the terminal connector in the electrical
compartment front face.
NOTE: For information about the operation of the wall controls, refer to the user guide.
TERMINAL
CONNECTOR
LOCATION
VD0278
4.2.1 ELECTRICALCONNECTION TO
ALTITUDE MAIN WALL CONTROL (EXCLUSIVELY FOR SOLO UNITS)
4.2.2 ELECTRICAL CONNECTION TO
DECO-TOUCH MAIN WALL CONTROL (ALL UNITS)
NO C NC I OC OL Y R G B
MODE
PREF
SET
NO C NC I OC OL Y R G B
SMART
VE0250
VE0175
14
4. CONTROLS (CONT’D)
4.2 ELECTRICAL CONNECTION TO OPTIONAL WALL CONTROL (CONT’D)
4.2.3 ELECTRICAL CONNECTION TO LITE-TOUCH CONSTRUCTO
(ALL UNITS) OR SIMPLE-TOUCH CONSTRUCTO MAIN
WALL CONTROL (EXCLUSIVELY FOR SOLO UNITS)
4.2.4 ELECTRICAL CONNECTION TO
CONSTRUCTO MAIN WALL CONTROL (ALL UNITS)
MAIN WALL CONTROL
LITE-TOUCH CONSTRUCTO
and
SIMPLE-TOUCH CONSTRUCTO
REAR VIEW
OFF MIN MAX
-5°C
23°F
#
CO
-
M FO R T Z ON E
XXX
XX
5°C
41°F
01/98
NO C NC I OC OL Y R G B
-20°C
-4°F
NO C NC I OC OL Y R G B
G B
OC
G B
Y
CONSTRUCTO
VE0100A
VE0102
4.2.5 ELECTRICAL CONNECTION TO OPTIONAL AUXILIARY WALL CONTROLS
60-MINUTE
CRANK TIMER
DEHUMIDISTAT
NOTE: If an optional auxiliary wall control is
activated and then, the Dehumidistat
is being activated, this one will
override the auxiliary wall control
commands.
PUSH-BUTTON TIMERS
(5 MAXIMUM)
NO C NC I OC OL Y R G B
VE0256A
COMPATIBLE OPTIONAL AUXILIARY WALL CONTROLS ACCORDING TO UNIT:
CONSTRUCTO
DEHUMIDISTAT
SOLO
DEHUMIDISTAT
60-MINUTE CRANK TIMER
20-MINUTE LIGHTED PUSH-BUTTON SWITCH (5 MAX.)
60-MINUTE CRANK TIMER
20/40/60 MINUTE LIGHTED PUSH-BUTTON TIMER (5 MAX.)
5. ELECTRIC CONNECTION TO THE FURNACE
! WARNING
Never connect a 120-volt AC circuit to the terminals of the furnace interlock (standard wiring). Only use the low
voltage class 2 circuit of the furnace blower control.
FOR A FURNACE CONNECTED TO A COOLING SYSTEM:
On some older thermostats, energizing the “R” and “G” terminals at the furnace has the effect of energizing “Y” at the thermostat and
thereby turning on the cooling system. If you identify this type of thermostat, you must use the ALTERNATE FURNACE INTERLOCK WIRING.
STANDARD FURNACE INTERLOCK WIRING
THERMOSTAT
TERMINALS
FOUR
WIRES
TWO WIRES
heating only
W
R
G
W
4 WIRES
G
Y
THERMOSTAT
TERMINAL
2 WIRES
heating only
wiring
nuts
W
RR
NO
NC
G
C
C
C
YY
Y
FURNACE
24-VOLT
TERMINAL BLOCK
R
UNIT TERMINAL CONNECTOR
Y
NO C NC I OC OL Y R G B
G
UNIT TERMINAL CONNECTOR
R
NO C NC I OC OL Y R G B
W
ALTERNATE FURNACE INTERLOCK WIRING
FURNACE
24-VOLT
TERMINAL BLOCK
TWO WIRES
2 WIRES
COOLING SYSTEM
VE0108A
15
COOLING SYSTEM
nc
BN
16
VE0257A
Fan
motor
M1
R
BL
GND GN
HI
O
COM
GY
LO
MED
BN
nc
Motor BK
capacitor
C1
BK
nc
nc
GY
BN
BN
nc
12
GN
BK
O
W
nc
nc
nc
BK
R
BK
W
Critical characteristic.
1 2 3 4 5 6
1 2 3
1 2 3 4 5 6
1 2 3
2
1
1
2
3
BK
J2
J8
F1
W1
W
GN
BK
J10
4 321
See note 1 2 1
J9
3 2 1
M H
5 4 3 2 1
Y BN
Y BN
J12
J11
BK
BL
BN
GY
GN
12
J3
12
54321
J1
R1
COLOR CODE
BLACK
O
ORANGE
R
RED
BLUE
W
WHITE
BROWN
Y
YELLOW
GRAY
nc
no connection
GREEN
Line voltage factory wiring
Class 2 low voltage factory wiring
Class 2 low voltage field wiring
Furnace blower interlock
J14-1 : NO
J14-2 : COM
J14-3 : nc
(optional; see notes 3, 5)
Override
switch
(optional; see
notes 3 & 4)
B GR Y
Field wiring
remote control
(see notes 3 & 4)
t˚
Defrost
temperature sensor
DAMPER
ELECTRONIC ASSEMBLY
10
9
8
J13 7
6
5
ICP
4
3
2
1
J14
21
A2
ELECTRONIC
ASSEMBLY A1
1 2 3 4 5
S1
Door interlock switch
T1
(magnetically actuated
reed switch)
24 V
class 2
9.5 V
W
W
class 2
120 V, 60 Hz
J4
J6
BK
120 V
M3
BK
NOTES
1. For continued fire protection. Use specified
UL listed/CSA Certified line fuse.
2. If any of the original wire, as supplied, must
be replaced, use the same equivalent wire.
3. Field wiring must comply with applicable
codes, ordinances and regulations.
4. Remote controls (class 2 circuit) available,
see instruction manual.
5. Furnace fan circuit must be class 2 circuit only.
Damper motor
JU1
1 2
WIRING DIAGRAM
120 V
24 V
class 2
9.5 V
class 2
HI
LOW
J8-5
J8-1
J8-2
J8-4
J9-4
J9-1
J9-2
J9-3
F1
J10-2
120 V, 60Hz
Line
CPU
1
2
3
JU1 K2
K3
K1
K5
K4
K2
J11-2
J11-1
J12-5
J12-4
K4 J12-3
J12-2
J12-1
K3
K5
J6-2 nc
J6-1 nc
J4-1
J4-3 nc
A1
LOGIC DIAGRAM
HI
MED
COM
LOW
J2-5
J2-4
J2-3
J2-2
J2-1
Damper motor
J4-2
J14-4
J14-5
J14-6
J14-7
J14-8
J14-9
J14-10
J14-2
J14-1
J14-3
Override
switch
(optional; see
notes 3, 4)
Field wiring
remote
control (see
notes 3, 4)
Furnace
blower
interlock
(optional; see
notes 3, 5)
Door interlock switch
J3-2
J3-1
A2
Fan
motor capacitor
Fan
motor
J10-1
120V, 60Hz
Neutral
6. WIRING DIAGRAM
! WARNING
Risk of electric shocks. Before performing any maintenance or servicing, always disconnect the unit from its
power source.
7. BALANCING THE UNIT
7.1 WHAT YOU NEED TO BALANCE THE UNIT
• A magnehelic gauge capable of measuring 0 to 0.5 inch of water
(0 to 125 Pa) and 2 plastic tubes.
• The balancing chart of the unit.
VP0009
7.2 PRELIMINARY STAGE TO BALANCE THE UNIT
• Seal all the unit ductwork with tape. Close all windows and doors.
• Turn off all exhaust devices such as range hood, dryer and bathroom fans.
• Make sure the integrated balancing dampers are fully open.
• Make sure all filters are clean (if it is not the first time the unit is balanced).
VD0280
7.3 BALANCING PROCEDURE
1. Set the unit to high speed.
Make sure that the furnace/air handler blower is ON if the installation is in any way connected to the ductwork of the cold air return. If
not, leave furnace/air handler blower OFF. If the outside temperature is below 0°C/32°F, make sure the unit is not running in defrost
while balancing. (By waiting 10 minutes after plugging the unit in, you are assured that the unit is not in a defrost cycle.)
2. Place the magnehelic gauge on a level surface and adjust it to zero.
3. Connect tubing from gauge to EXHAUST air flow pressure taps (see diagram
at right). Be sure to connect the tubes to their appropriate high/low fittings. If the
gauge drops below zero, reverse the tubing connections.
NOTE: It is suggested to start with the exhaust air flow reading because the
exhaust has typically more restriction than the fresh air, especially in
cases of fully ducted installations or source point ventilation.
Place the magnehelic gauge upright and level. Record equivalent AIR FLOW of
the reading according to the balancing chart.
EXHAUST AIR FLOW
4. Move tubing to FRESH air flow pressure taps (see diagram). Adjust the fresh
air balancing damper until the FRESH air flow is approximately the same as
the EXHAUST air flow. If FRESH air flow is less than EXHAUST air flow, then
go back and adjust the exhaust balancing damper to equal the FRESH air flow.
5. Secure both dampers in place with a fastening screw.
6. Write the required air flow information on a label and stick it near the unit for
future reference (date, maximum speed air flows, your name, phone number
and business address).
VP0022
FRESH AIR FLOW
7. Install 4 pressure taps plugs (included in parts bag).
NOTES: 1. Use conversion chart provided with the unit to convert magnehelic gauge readings to equivalent cfm values.
2. The unit is considered balanced even if there is a difference of ±10 cfm (or ± 5 l/s or 17 m³/h) between the two air flows.
17
8. SERVICE PARTS
1
19
2
18
3
5
4
15
17
14
8
6
7
15
9
16
12
10
13
11
VL0050
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
*
*
DESCRIPTION
Hinge assembly kit
Damper supply port assembly
Damper system actuator
(including no. 4)
Thermistor kit
Capacitor 7.5 μF
Electronic board
Transformer
Double collar port
Blower assembly (including no. 10)
Square damper kit
Magnet switch
Door assembly
(including hinges and latches)
Door latches (keeper)
and screws
Diffuser
Filter kit
Core
Door latches
and screws
Balancing damper
Balancing double collar port
Terminal connector
Hardware kit
HRV CONSTRUCTO
1.5ES
46110
1601702
HRV CONSTRUCTO
2.0ES
47110
ERV CONSTRUCTO
2.0ES
47115
46720
46725
HRV SOLO
2.0ES
47720
13036
17245
13036
17245
13036
17245
13036
17245
13036
17245
13036
17245
13036
17245
17235
17235
17235
17235
17235
17235
17235
17242
17240
60809
17244
60818
60804
17243
19060
17242
17240
60809
17244
60818
60804
17243
19060
17242
17240
60809
17244
60818
60805
17243
19060
17242
17240
60812
17244
60818
60806
17243
19060
17242
17240
60810
17244
60818
60804
17243
19060
17242
17240
60810
17244
60818
60804
17243
19060
17242
17240
60810
17244
60818
60805
17243
19060
60797
60797
60797
60798
60797
60797
60797
00887 (2)
00601 (4)
60822
60800
60802
00886 (2)
00601 (4)
02253
02256
16416
20510
00887 (2)
00601 (4)
60822
60800
60801
00886 (2)
00601 (4)
02253
02256
16416
20510
00887 (2)
00601 (4)
60822
60800
60803
00886 (2)
00601 (4)
02253
02256
16416
20510
00887 (2)
00601 (4)
–
60799
16582
00886 (2)
00601 (4)
02253
02256
16416
20606
00887 (2)
00601 (4)
60822
60800
60802
00886 (2)
00601 (4)
02253
02256
16416
20606
00887 (2)
00601 (4)
60822
60800
60801
00886 (2)
00601 (4)
02253
02256
16416
20606
00887 (2)
00601 (4)
60822
60800
60803
00886 (2)
00601 (4)
02253
02256
16416
20606
HRV SOLO 1.5ES
* Not shown.
REPLACEMENT PARTS AND REPAIRS
In order to ensure your ventilation unit remains in good working condition, you must use Venmar Ventilation Inc. genuine replacement parts only. The Venmar Ventilation Inc.
genuine replacement parts are specially designed for each unit and are manufactured to comply with all the applicable certification standards and maintain a high standard of
safety. Any third party replacement part used may cause serious damage and drastically reduce the performance level of your unit, which will result in premature failing. Also,
Venmar Ventilation Inc. recommends to contact a certified service depot for all replacement parts and repairs.
18
9. TROUBLESHOOTING
If the integrated control LED of the unit is flashing, this means the unit sensors detected a problem. See the list below to know where on
the unit the problem occurs.
LED flashes GREEN (double blink).
LED flashes AMBER.
• Thermistor error.
• Damper error.
Replace the thermistor kit.
Go to point 10.
! WARNING
A few diagnosis procedures may require the unit to be in operation while proceeding. Open the unit door and
bypass its magnetic switch by putting the door white magnet on it. Be careful with moving and/or live parts.
PROBLEMS
POSSIBLE CAUSES
YOU SHOULD TRY THIS
1. The error code E1 is • The wires may be in reverse position.
displayed on Altitude or
Deco-Touch wall control • The wires may be broken.
screen.
• The wires may have a bad connection.
• The unit is not compatible with
Altitude wall control (Constructo).
• Ensure that the color coded wires have been connected to their appropriate
places.
• Inspect every wire and replace any that are damaged.
• Ensure the wires are correctly connected.
• Refer to unit spec. sheet for control compatibility.
2. There is no outside
temperature
displayed
on Altitude wall control
screen
.
NOTE: At its very start-up or after a power failure, it takes some minutes before
the outside temperature appears on screen. The delay duration depends
on which operation mode the wall control is set. The shortest delay is
obtained when the wall control is set on MIN or MAX in VENT Mode.
• Check if unit is operating.
• The Altitude or Deco-Touch wall
control is defective.
• Reset the Altitude or Deco-Touch wall BOTH DURING 8 SEC.
control by pressing simultaneously
on both keys for 8 second (as shown
at right). Then, unplug the unit for VQ0048A
ALTITUDE
30 seconds. Plug the unit back.
3. Altitude or Deco-Touch • The Altitude or Deco-Touch wall
wall
control
screen
control needs to be reset.
alternates
between
normal display and E3 or
E4 appears on screen.
• Unit is on error and integrated control
LED flashes (GREEN or AMBER).
• The unit thermistor is defective • Replace the unit thermistor.
(integrated control LED flashes
GREEN).
VQ0062
DECO-TOUCH
• If the problem is not solved, replace the Altitude or Deco-Touch wall control.
4. On Altitude wall control, • Exterior air intake port is blocked.
there is an important • The unit thermistor is defective
difference
between
(integrated control LED flashes
temperature
displayed
GREEN).
and real temperature.
• The unit damper has been blocked
or broken (integrated control LED
flashes AMBER and unit is OFF).
• Motor won’t turn.
• Clean the exterior air intake port.
• Replace the unit thermistor.
5. Unit does not work • The transformer may be defective.
(no LED is lit on the • The circuit board may be defective.
integrated control).
• Check for 24 VAC on J8-1 and J8-2.
• Unplug the unit. Disconnect the main control
and the optional(s) control(s) (if need be). NO C NC I OC OL Y R G B
Jump G and B terminals. Plug the unit back
and wait about 10 seconds. If the motor runs
on high speed and the damper opens, the VE0097
circuit board is not defective.
• Plug the unit.
• Close unit door.
• Inspect fuse on circuit board (refer to wiring diagram F1 on page 16).
• Try the integrated control (see Section 4.1 on page 13).
•
•
•
•
The unit is unplugged.
The unit door is opened.
A fuse is blown.
Wrong control connections.
• Check for the proper operation of the unit damper; replace if necessary.
• Confirm that the motor is running, if not refer to point 9.
6. The damper actuator • The damper actuator or the integrated • Unplug the unit. Disconnect the main control and the optional controls(s) (if
does not work or rotates
damper port mechanism may be
need be). Wait 10 seconds and plug the unit back. Check if the damper opens.
continuously.
defective (integrated control LED
If not, use a mulltimeter and check for 24 VAC on J12-1 and J12-2 (in electrical
flashes AMBER and unit is OFF).
compartment). If there is 24 VAC, replace the entire port assembly.
NOTE: It is normal to experience a small delay (7-8 seconds) before detecting
the 24 VAC signal at starting-up. This signal will stay during 17-18
seconds before disappearing.
• The circuit board or the transformer • If there is no 24 VAC, check for 24 VAC between J8-1 and J8-2. If there is 24 VAC
replace the circuit board, and if there is no 24 VAC, change the transformer.
may be defective.(integrated control
LED flashes AMBER and unit is OFF)
19
9. TROUBLESHOOTING (CONT’D)
PROBLEMS
POSSIBLE CAUSES
YOU SHOULD TRY THIS
7. The wall control does • The wires may be in reverse position. • Ensure that the color coded wires have been connected to their appropriate
not work OR its indicator
places.
flashes.
• Inspect every wire and replace any that are damaged.
• The wires may be broken.
• The wire in the wall OR the wall • Remove the wall control and test it right beside the unit using another shorter
wire. If the wall control works there, change the wire. If it does not, change the
control may be defective.
wall control.
8. The Dehumidistat does • The wires may be in reverse position. • Ensure that the color coded wires have been connected to their appropriate
not work OR the pushplaces.
button timer does not • The Dehumidistat or push button may • Jump the OL and OC terminals. If the
work OR its indicator light
unit switches to high speed, remove the NO C NC I OC OL Y R G B
be defective.
does not stay on.
Dehumidistat or push button and test it right
beside the unit using another shorter wire. If
it works here, change the wire. If it doesn’t, VE0098
change the Dehumidistat or the push button.
9. The motor does not work.
• The circuit board may be defective.
•
•
•
•
•
•
• Press on the integrated control push button until the unit turns on low speed
(the LED will light AMBER). Using a multimeter, check the voltage on J9-4 and
J9-3. Refer to Section 6 Wiring Diagram. The reading must be 120 VAC Then
set the unit on high speed by pressing on the integrated control push button one
more time (the LED will light GREEN). Using a multimeter, check the voltage
on J9-4 and J9-2. The reading must be 120 VAC Check also between J4-2 and
J4-1, the reading must be 120 VAC Refer to Section 6 Wiring Diagram. Check if
the fuse F1 is intact. If all the readings correspond to the right voltage values,
the circuit board is not defective. If one or both readings are different, change
the circuit board.
• Using a multimeter, check for 120 VAC for the following speeds: High Speed:
The motor may be defective.
between GREY and ORANGE wires; Low/Medium Speed: between GREY
and RED/BLUE wires. Refer to Section 6 Wiring Diagram.
The motor capacitor may be defective. • Unplug the unit. Check for continuity between Pin 5 on the 6-pin connector
(brown leads) and Pin 3 of the capacitor connector. Also check for continuity
between Pin 4 on the 6-pin connector (brown leads) and Pin 1 of the capacitor
connector. Refer to Section 6 Wiring Diagram.
The motor is unplugged from inside • Open the door and ensure that the wire going to the motor is connected.
the unit.
The motor is unplugged from the • Check J4 motor connection on circuit board.
electronic board (J4).
There is a problem with the door • Door magnet switch is missing or not in its place (see item no. 11 on page 18).
magnet switch.
JU-1 jumper is missing or in wrong • Ensure JU-1 jumper is set on “M” speed (refer to Section 6 Wiring Diagram).
position.
10. The defrost cycle does • Ice deposits may be hindering the
not work (the fresh air
damper operation.
duct is frozen OR the • The damper rod or the port damper
fresh air distributed is
itself may be broken.
very cold).
• The damper actuator or circuit board
may be defective.
11. The integrated control
push button does not
work.
• Remove the ice.
• Inspect these parts and replace if necessary.
• See point 6.
• The 30-second boot sequence is not • See Section 4.1.1 Boot Sequence (page 13).
completed.
• The circuit board may be defective.
• Check voltage going to circuit board J8-1 and J8-2.
• The transformer may be defective.
• Check for 24 VAC on J8-1 and J8-2.
20
">