advertisement
USER'S MANUAL
SUPER RESOLUTION CAMERA
1. Specifications
ITEM Super High Resolution Series
Power Source DC 12V ( Option : AC24V )
Image Sensor
Total Pixels
Effective Pixels
Maximum Aperture Ratio
Scanning System
1/3 ” SONY SUPER HAD CCD,
410,000 pixels
811(H) x 508(V) , 1/3 ” CCD
768(H) x 494(V) , 1/3 ” CCD
1 : 1.3 ~2.0
2 : 1 Interlaced 525 Lines / 60Fields / 30Frames
Video Output
Resolution
Back Light Compensation
Gain Control
Electric Shutter Speed
SENS-UP
WHITE BALANCE
Min. Illumination
S/N ( Y signal)
Digital Noise Reduction
Motion Detection
On Screen Display
PRIVACY Function
1.0V [p-p] Composite, 75 Ω
580 TV Line
BLC / HLC / OFF
LOW / MIDDLE / HIGH
1/60 ~ 1/200,000 sec
AUTO/OFF ( x2 ~ x256)
ATW/AWC/MANUAL/INDOOR/OUTDOOR
0.05Lux (Color), 0.00002Lux (Sense-up)
52dB (Weight On)
ON / OFF
ON / OFF (8 Zone)
Built - in
ON / OFF (8 Zone)
2. Features
1) HLC(Highlight Compensation)
When the image is in front of strong background lighting, your camera allows you to get the clear image.
2) SENS UP(Fine Picture Condition Under Very
Low Illumination)
1/3"inch density CCD and digital processor permit high quality pictures to be captured in very low light condition.
3) High Resolution
The horizontal resolution of 580TVL lines can be achieved by using a SONY CCD having Double Speed 410,000pixels noiseless and reliable pictures.
4) OSD
Your Camera detects motion of object without sensor outside.
5)DIS (Digital Image stabilizer)
You can control a lot function on the screen.
6) DNR (Digital Noise Reduction) CHIP
It has an assistant DSP chip that can remove image noise efficiently and it shows clean and obvious image in low luminance.
7) DAY/NIGHT
In normal or high luminance, camera maintains color mode. On the contrary, it get changed into B/W mode in low luminance.
3) WHITE BAL.
<ATW / INDOOR / OUTDOOR / AWC->SET /
MANUAL>
Controls color on the screen.
ATC : Select Auto Tracking White Balance (ATW) when the
color temp. is 1800°K~10500°K.
INDOOR : Select this when the color temp. is 4500°K ~
Please read this manual thoroughly before operation and keep it handy for further reference.
3. Camera OSD Control
UP
LEFT RIGHT
DOWN
SETUP(MENU):Push Down
Press this control
UP, DOWN
LEFT, RIGHT
SETUP(MENU)
To do this
Select a new item
Select a menu item
Access a submenu
4. OSD Menu Structure
SETUP MENU
LENS Option
DC MANUAL
EXPOSURE
SHUTTER
WHITE BALANCE
AGC SENS-UP RETURN
ATW
BACKLIGHT
BLC
INDOOR
HLC
DNR
ON
DAY/NIGHT
COLOR
IMAGE ADJ.
OFF
B/W
FREEZE
D-ZOOM
SPECIAL
CAMTITLE
PRIVACY
RESET
EXIT
OUTDOOR
SYNC
DIS
RETURN
OFF
AUTO
V-REV
SHARPNESS
AWC->SET
EXTERN
H-REV
RETURN
MOTION DET
LANGUAGE
MANUAL
5. SETUP Menu Functions
1) LENS
<Option : DC / MANUAL>
Selects Lens Type.
2) EXPOSURE
<Option : SHUTTER/AGC/SENS-UP/RETURN>
Adjusts exposure settings.
SHUTTER :
FLK - Flicker-less mode (FLK) reduces on-screen flickering.
ESC - Electronic Shutter Control (AUTO) adjusts brightness
level on screen.
Manual - Manual mode allows you to adjust the shutter speed
from 1/60~1/120,000 of a second (NTSC), or 1/50~
1/100,000(PAL).
AGC : Adjusts value of AGC gain. Increase the GAIN level to
brighten the picture. (noise / distortion may develop)
SENS-UP : Automatically provides a clear image under low-
light conditions. You can control the maximum low-light
magnification from 2x to 256x (increasing magnification may
cause noise/distortion). DSS is deactivated when SHUTTER
is set to FLK mode.
2) SYNC
<Option : INT / L/L>
INT = Synchronize the vertical interval sync pulse of your camera with other equipment to reduce the effect of picture roll on the monitor.
color temp. is 1800°K~10500°K.
INDOOR : Select this when the color temp. is 4500°K ~
8500°K.
OUTDOOR : Select this when the color temp. is 1800°K
~10500°K (sodium light inclusion).
AWC->SET : Set the point the camera towards a sheet of
white paper and press the SET button.
Manual : It allows you to increase or decrease the red or
blue factor on screen.
4) BACKLIGHT
<Option : BLC / HLC / OFF>
BLC : Provides light level control to overcome severe
backlighting conditions.
HLC : High Light Compensation. Removing the high light
and it makes possible to view the image clearly.
5) DNR
<Option : ON / OFF>
Reduces noise/distortion on the screen, Increasing the
DNR level reduces noise but may introduce video artifacts.
DNR is deactivated if AGC is turned off.
6) DAY/NIGHT
<Option : COLOR/BW/AUTO/EXTERN>
COLOR : Full time color mode.
BW : Full time black and white mode.
AUTO : Automatically detect color or black/white
EXTERN : Same function as "AUTO", but with external sensor such as CDS sensor.
7) IMAGE ADJ.
<Option : FREEZE / V-REV / H-REV
D-ZOOM / SHARPNESS / RETURN>
FREEZE : To view still or moving pictures.
V-REV : Flip the picture vertically on the screen.
H-REV : Flip the picture horizontally on the screen.
D-ZOOM : Digital zoom of x1 ~x10.
SHARPNESS : Sharpen the image on screen.
Excessive sharpening may cause picture noise.
RETURN : Save the settings and return to the SETUP menu.
6. SPECIAL Menu Functions
On the SETUP menu, press the menu control UP or DOWN and then select SPECIAL.
Press the SETUP(MENU) control to access the SPECIAL
MENU.
1) CAMTITLE
<Option : OFF / ON>
Display a name and/or number on the monitor.
To add a camera title:
UP, DOWN, LEFT, RIGHT menu control = Select a character, then press (SETUP)MENU to accept it. The character is saved and the title cursor at the bottom of the screen moves to the next position.
← → = Go back or forward in the title name to make changes.
CLR = Delete the entire name and start again.
POS = Position the camera title on the screen.
Press (SETUP)MENU to confirm the position.
END = Accept the new name.
equipment to reduce the effect of picture roll on the monitor.
L/L (Line Lock) = Adjust the phase from
0 ° ~ 359 ° .
INTERNAL = When line lock is not required.
LINELOCK = Adjust the vertical phase(VPH) from 000 -
359 (factory default is 0). Line line is only available with
24VAC power.
RETURN = Press MENU to return to the SETUP menu.
3) MOTION DET
<Option : OFF / ON>
Detect moving objects in 8 different areas on screen;
‘MOTION DETECTED’ is displayed on the screen when movement is detected.
SENSITIVITY : Select 8 different Motion Detection area. When sensitivity number is high, it can recognize even small movement.
AREA MODE : Activate or deactivate the selected area.
SEL POS : Select setting point from 4 different point, Left-Top,
Left-Bottom, Right-Top and Right-Bottom.
YPOS : Move setting point to vertical direction.
XPOS : Move setting point to horizontal direction.
FILL SET : Fills selected area with proper color.
RETURN : Save the settings and return to the SPECIAL menu.
4) PRIVACY
<Option : OFF / ON>
Mask up to 8 areas of the screen from video monitoring.
AREA SEL = Select up to 8 motion detection area.
AREA mode : Activate or deactivate the selected area.
MASK COLOR : Select area color.
TRANSP : Adjust the transparency of selected area.
RETURN : Save the settings and return to the SPECIAL menu.
5) DIS
<Option : OFF / ON>
Digital Image Stabilizer. Reduce picture movement due to external factors.
6) LANGUAGE
Choose language that should be displayed.
7) RESET
Restore all factory default settings.
8) RETURN
Return to the main SETUP menu.
This manual is based on the date as shown in the right and specifications are subject to chage without notice for quality
VER.090714
advertisement
Related manuals
advertisement