Clinton Electronics CE-D970 manual

Super DNR High Resolution

Color Dome Camera

CE-D970

The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

INFORMATION - This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING - Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.

CAUTION : To prevent electric shock and risk of fire hazards:

◆

Do NOT use power sources other than those specified.

◆

Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should conform to all local codes.

1

Super DNR High Resolution Color Dome Camera

■

Contents

Features

Warnings and Precautions

Components

Names and Functions of Parts

■ Lens

■ OSD

■

VBS-EXTRA

■

SMPS

■

SMPS

■

REMOTE CONTROLLER

Installation

Dimensions

Cable Connections

11

13

9

11

11

11

10

10

11

14

4

5

8

How to Use the Camera

■

Function Menu Structure

■

How to Set up the Functions

ㆍ

LENS

ㆍ

EXPOSURE

ㆍ

WHITE BALANCE control

ㆍ

BACKLIGHT

ㆍ

DNR (Digital Noise Reduction)

ㆍ

DAY/NIGHT

ㆍ

IMAGE ADJ

ㆍ

SPECIAL

ㆍ

EXIT

Troubleshooting

Specifications

34

36

15

27

29

33

21

22

24

25

15

16

17

19


2 3


■

Features

Ultra High Resolution

By adopting a 1/3" 410,000 pixel Sony CCD, the camera produces clear picture quality with a horizontal resolution of 580 TV lines for color, and 700 TV lines for B/W.

Day & Night

The camera identifies whether it is day or night and automatically switches to the appropriate mode, depending on its environment. By day, the camera switches to color mode in order to maintain optimal color. At night, it switches to

B/W mode so as to obtain better picture definition.

Excellent Sensitivity

Adopting a Diagonal 6mm (1/3"), highly sensitive

CCD and digital signal processing technology, it can clearly distinguish the outline and color of a subject in an extremely low luminance environment . even, for example, under starlight.

Since surveillance is possible in places where the light is poor, the camera is appropriate for day and night surveillance outdoors or on the outside of buildings.

Miscellaneous Functions

SYNC (INT/LL), SENS-UP, FREEZE, FLIP

(H/V-REV), D-ZOOM, SHARPNESS, MOTION

DETECTION and PRIVACY functions are provided.

Built-in Coax and UTP video connections

DNR (Digital Noise Reduction)

The amount of low illuminance noise has been significantly reduced, and the signal-to-noise ratio (S/N ratio) as well as horizontal resolution have been improved, resulting in a clear and sharp image display even in the dark.

OSD

The camera control is convenient by using

7 different foreign language O.S.D.

- NTSC : Korean, English, Spanish, Japanese

- PAL : English, French, German, Spanish,

Italian, Chinese

Motion Detection

The camera detects motion and generates a screen message without an external sensor.

3 Axis built-in 100mm Dome Housing with Adaptor Plate Bracket

DIS (Digital Image Stabilizer)

The DIS function compensates for any camera movement, to produce more stable pictures.

Warning ■

The camera requires periodic inspection.

Contact an authorised technician to carry out the inspection.

Stop using your camera when you find it malfunctioning.

If the camera emits smoke or is unusually hot for a long period, a fire may be caused.

Do not Install the camera on a surface that can not support it.

If the camera is installed on an inappropriate surface, it may fall and cause injury.

Do not hold plug with wet hands.

It could cause an electric shock.

Do not dis-assemble the camera.

It may result in an electric shock or other hazards.

Do not use the camera close to a gas or oil leak.

It may result in a fire or other hazards.


4 5


■

Precautions

Do not install the camera in extreme temperature conditions.

Do not install or use the camera in an environment where the humidity is high.

Only use the camera under conditions where temperatures are between

-10˚C and +50˚C. Be especially careful to provide ventilation when operating under high temperatures.

It can cause the image quality to be poor.

Do not install the camera under unstable lighting conditions.

Do not touch the front lens of the camera.

Do not drop the camera or protect it from physical shocks.

Never keep the camera pointed directly at strong light.

It can cause malfunctions to occur.

Do not expose the camera to rain or spill beverage on it.

It can damage the CCD.

Do not expose the camera to radioactivity.

Severe lighting change or flicker can cause the camera to work improperly.

This is one of the most important parts of the camera. Be careful not to leave fingerprints on the lens cover.


6

If it gets wet, wipe it dry immediately.

Liquids can contain minerals that corrode the electronic components.

If exposed to radioactivity the CCD will fail.

ㆍ

If the camera is exposed to spotlight or object reflecting strong light, smear or blooming may occur.

ㆍ

Please check that the power satisfies the normal specification before connecting the camera.

7


■

Components

1. COLOR DOME CAMERA

2. SCREWS

3. WIRE FOR VBS-EXTRA

4. INSTRUCTION GUIDE


8

Names and Functions of Parts ■

9


■


①

LENS : Vari-Focal DC Auto Iris Lens

②

OSD PCB

BA101

UP

LEFT

DOWN

RIGHT

DIN1

CN4

●

Jog Shuttle Switch

-

Push button : Used for the menu display. This button can be used to

confirm settings after changing the value of the selected

function or current conditions.

-

-

& : Used for selecting items by moving the cursor up or down

on the menu screen

& : Used when changing item values, by moving the cursor to

the left or right on the menu screen.


10

Names and Functions of Parts ■

③

VBS-EXTRA FOR CONNECTING TO LCD

Please use the supplied wire when connecting to LCD

VBS-EXTRA

④

3 AXIS BRACKET

Please loosen screws and fix tilted and panned position.

⑤

SMPS PCB FOR DUAL POWER - IF APPLICABLE

⑥

REMOTE CONTROLLER

SET

( Optional Item )

●

SET

: Used to access menu mode and for configuration.

: Moves cursor up the menu screen.

: Moves cursor down the menu screen.

: Moves cursor left in the menu screen.

Parameter change

: Moves cursor right in the menu screen.

Parameter change

11


■


DECORATION RING

DOME COVER

■

Dimensions

100φ

GIMBAL A'SSY

BASE HOUSING

73.0

φ

125.79φ


12

(unit : mm)

1. Dome Base Mounting

- Open the dome by unscrewing the ring from the base-remove it

by unscrewing the ring and dome anti-clockwise.

- Mount the camera base to a sturdy surface using the supplied screws

and the premade holes on the base of the dome.

2. Power Connect & Monitor Impedance

- DC12V/300mA regulated power supply (DC12V only)

AC24V Class 2 power supply (AC24V/DC12V)

- To avoid fire or shock hazard, must use a UL listed power supply.

- Set the monitor impedance switch to 75Ω. Check the impedance

switch when the screen turns blurred.

3. Camera Module Adjustment

- Loosen screws for 3-axis camera bracket and adjust the direction

and angle of camera.

- Make sure to retighten the screws for camera bracket.

- Set any function you wish to activate by using the OSD buttons.

4. Dome Cover Mounting

- Replace the ring and dome by locating it on the base and turning

it clockwise.

5. When using UTP Cable

- Connect UTP(Unshield Twisted Pair) wire to the UTP output of the

camera directly. UTP transmitter is included in the camera therefore

additional UTP transmitter is not necessary.

- UTP receiver is necessary to connect UTP wire to Monitor or DVR.

- When connecting UTP wire, make sure the polarity of the video signal is correct.

- Use UTP wire "CAT 24AWG" to have the best transmission quality.

■

Cable Connections

POWER

VIDEO(COAX)

VIDEO(UTP)

DC only

AC24V

DC12V AC IN

DC IN

13


■


Adapter Plate

Unlocking direction

Locking direction

3.5x25 tapping screw (provided)

Camera Body

Unlocking direction

Locking direction

Dome Cover

* When installing on an adapter plate bracket.

①

Place the adapter plate bracket on a flat installation surface and fix it with

the screws provided.

②

When placing the camera body onto the plate, insert the plate pin into the

corresponding holes on the camera body as shown in figure-1. Lock the

camera in place by turning the camera body clockwise.

③

When placing the camera body on the plate, make sure that the power and

video cables are passed through.

④

After installation and adjustment of the camera is complete, secure the dome

cover by turning it clockwise.


14

How to Use the Camera ■

On-Screen Display Menu Structure

LENS

EXPOSURE

WHITE BALANCE

BACKLIGHT

DNR

DAY/NIGHT

IMAGE ADJUSTMENT

(IMAGE ADJ.)

SPECIAL

Setup Menu

•

DC

•

MANUAL

•

SHUTTER

•

AGC

•

SENS-UP

•

RETURN

• ATW • MANUAL • AWC SET

•

OUTDOOR

•

INDOOR

•

OFF

•

BLC

•

HLC

•

ON

•

OFF

•

COLOR

•

B/W

•

AUTO

•

EXTERN

•

FREEZ

•

V-REV

•

H-REV

• D-ZOOM • SHARPNESS

•

RETURN

•

CAMTITLE

•

SYNC

•

MOTION DET

•

PRIVACY

•

DIS

•

COMM ADJ

•

LANGUAGE

•

RESET

•

RETURN

EXIT

15


■


How to Set up the Functions

Settings can be made using the 5 buttons on the rear of the camera.

BA101

DIN1

CN4

UP

LEFT

DOWN

RIGHT

1. Press the SET button.

• The Setup menu is displayed on the monitor screen.

MAIN SETUP

1. LENS

2. EXPOSURE

DC

3. WHITE BAL

4. BACKLIGHT

5. DNR

6. DAY/NIGHT

7. IMAGE ADJ

8. SPECIAL

9. EXIT

ATW

OFF

ON

AUTO

2. Select a menu item using the Up and Down buttons.

• Place the cursor over a desired item.


16

Select the desired menu item by using the UP and

DOWN buttons.

MAIN SETUP

1. LENS

2. EXPOSURE

DC

3. WHITE BAL

4. BACKLIGHT

5. DNR

ATW

OFF

ON

6. DAY/NIGHT

7. IMAGE ADJ

8. SPECIAL

9. EXIT

AUTO

Modes can be changed using the LEFT and

RIGHT buttons.

3. Set up a selected item by using the Left and Right buttons.

4. To finish and save the settings, select 'EXIT' and press the SET button.

Note

• An item with the icon also has sub-menus. To select a sub-menu, press the SET button.

• An item with the - - - icon has no sub-menus available for selection.

LENS

This function is used to adjust the brightness of the screen.

1. When the SETUP menu screen is displayed on the screen, position the

cursor to point to LENS using the Up and Down buttons.

2. Select the type of lens using the Left and Right buttons.

MAIN SETUP

1. LENS

2. EXPOSURE

DC

3. WHITE BAL ATW

17


■


●

MANUAL: Manual Lens selection

●

DC : Auto Iris Lens selection

Note

•The brightness of the screen can be adjusted in DC mode.

The brightness can be adjusted within the range of 1 ~ 70.

The optimum level of brightness for the user can be achieved by adjustment.

• If you select the MANUAL mode, it can be adjusted in ESC mode.

3. Press the SET button if you wish to return to the previous menu


18

EXPOSURE

MAIN SETUP

1. LENS

2. EXPOSURE

DC

3. WHITE BAL

4. BACKLIGHT

ATW

OFF

5. DNR

6. DAY/NIGHT

7. IMAGE ADJ

8. SPECIAL

9. EXIT

ON

AUTO

1. When the SETUP menu screen is displayed select EXPOSURE using

the Up and Down buttons.

2. Select the desired mode using the Left and Right buttons.

●

SHUTTER : Select either auto or manual shutter.

- A.FLK : Select this when picture flicker is expereinced, which can happen

when there is a clash with the frequency of the installed lighting.

- ESC : Select this to control the shutter speed automatically. If ESC is

selected, the shutter speed is automatically controlled according

to the ambient illumination available.

- MANUAL : The shutter speed is controlled manually.

19


■


Note

• When the SHUTTER is set to ESC, and the camera is set to Internal

Synchronisation, the picture may become unstable if the camera faces a bright fluorescent light. Therefore, take care when choosing the installation position.

• ESC and MANUAL modes are only available together when the lens is set to MANUAL.

• When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP is disabled.

●

AGC (AUTO GAIN CONTROL):

The higher the gain level, the brighter the screen - but the higher the noise.

- OFF : Deactivates the AGC function.

- LOW : Allows automatic gain control from 0 to 24dB.

- HIGH : Allows automatic gain control from 0 to 42dB.

●

SENS-UP :

When it is night or dark, the camera automatically detects the light level and maintains a clear picture if this mode is activated.

- OFF : Deactivates the SENS-UP function.

- AUTO : Activates the SENS-UP function.

●

RETURN :

Select this to save the changes in the EXPOSURE menu and return to the SETUP menu.

Note

• If you press the SET button in 'AUTO' mode, You can adjust brightness by increasing or decreasing the shutter speed. (X2~X256)

• Note that the higher the zoom level, the brighter the screen, but the more likely it is that an after-image will appear.

• Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation when the zoom level is increased, this is normal.


20

White Balance (White Bal.)

Use the White Balance function to adjust the screen colors.

1. Position the cursor to point to WHITE BAL on the SETUP menu screen

select using the Up and Down buttons.


MAIN SETUP

1. LENS

2. EXPOSURE

DC

3. WHITE BAL

4. BACKLIGHT

5. DNR

ATW

OFF

ON

※

Select one of the following 5 modes, as appropriate.

●

ATW : Select when the color temperature is between 1800˚K and 10500˚K

●

INDOOR : Select when the color temperature is between 4500˚K and 8500˚K

●

OUTDOOR : Select when the color temperature is between 1800˚K and

10500˚K. (sodium light inclusion)

●

AWC SET : To obtain the optimum state under the current luminance

levels, direct the camera to point toward a sheet of white

paper and press the SET button. If the environment changes,

including the light source, the white balance will require

re-adjustment.

●

MANUAL : Select to "fine-tune" the White Balance manually. Set White

Balance first using the ATW or AWC mode. Afterwards

switch to MANUAL mode, fine-tune the White Balance

and then press the SET button.

21


■


Note

• Under the following conditions White Balance may not work properly.

In such cases, select the AWC mode.

①

When the color temperature of the subject environment has a very high temperature range (e.g. clear sky, or sunset)

②

When the ambient illumination of the subject is low.

③

If the camera is directed toward a fluorescent light, or is installed in a place where illumination changes dramatically, the White Balance operation may become unstable.

BACKLIGHT

This camera is designed to deliver a clear and distinct image of both subject and background, even when the subject is in backlit, using a proprietary

SV-IV DSP chip.

1. Position the cursor to point to BACKLIGHT on the SETUP menu screen

using the Up and Down buttons.

MAIN SETUP

1. LENS

2. EXPOSURE

DC

3. WHITE BAL

4. BACKLIGHT

5. DNR

6. DAY/NIGHT

7. IMAGE ADJ

8. SPECIAL

9. EXIT

ATW

OFF

ON

AUTO

2. Select a desired mode using the Left and Right buttons depending on the

camera purpose.


22

●

BLC : Enables a user to directly select a desired area from a picture, and

to view the area more clearly.

BLC ON

BLC OFF

●

HLC (High Light Compensation) :

If there is a high light installed in a limited environment such as an

apartment parking garage or gas station entrance, removing the

high light makes it possible to view car license plates efficiently.

- DAY : In normal daylight conditions, the HLC is not activated.

- NIGHT : If a high light that is larger than a certain size is present on

the screen, remove the high light to see license plates clearly.

HLC MASKING AREA

HLC ON

●

OFF : Not being used

HLC OFF

3. Select a desired mode using the Left and Right buttons and press the SET button.

●

Select 'BLC' to adjust the area to be

enhanced and enhancement level.

●

HLC : Enable a user to select a mask

color of high light area from a picture.

23


■


Note

• Because there can be a difference in the effectiveness of HLC

according to the amount of light area in the screen, optimize the

installation angle for the best HLC performance.

• In a dark environment, the HLC is only activated when a high light

that is larger than a certain area is present.

• The HLC is not activated in light or overly dark conditions.

DNR

This function reduces the background noise in a low luminance environment.

1. When the SETUP menu screen is displayed, select 'DNR' using the

Up and Down buttons.

MAIN SETUP

1. LENS

2. EXPOSURE

DC

3. WHITE BAL

4. BACKLIGHT

5. DNR

6. DAY/NIGHT

ATW

OFF

ON

AUTO

7. IMAGE ADJ

8. SPECIAL

9. EXIT

2. Select a desired mode using the Left and Right buttons.

●

OFF : Deactivates DNR. Noise is not reduced.

●

ON : Activates DNR so that noise is reduced.


24

3. Set the DNR mode to 'ON' and press the SET button. The noise

reduction level can now be adjusted.

Note

• You cannot set the DNR to 'ON' or 'OFF' when the AGC mode in the

EXPOSURE menu is 'OFF'.

• When adjusting the noise reduction level in DNR mode, remember that the higher the level is set, the greater the reduction in noise level, but it also increases the possibility of ghosting.

DAY/NIGHT

Pictures can be displayed in either color or black and white.

1. When the SETUP menu screen is displayed, select 'DAY/NIGHT' using


MAIN SETUP

1. LENS

2. EXPOSURE

DC

3. WHITE BAL

4. BACKLIGHT

ATW

OFF

5. DNR

6. DAY/NIGHT

7. IMAGE ADJ

8. SPECIAL

9. EXIT

ON

AUTO

25


■



●

COLOR : The picture is displayed in color.

●

B/W : The picture is always displayed in black and white.

●

AUTO : This camera has an IR Cut-Filter and automatically

changes to the appropraite mode according to lighting

levels.To set up the switching time and switching speed

for the AUTO mode press the SET button.

●

EXTERN : This mode allows the application of a filter to external signals.

Note

• The DAY/NIGHT menu cannot be controlled when AGC in the

EXPOSURE menu is 'OFF'.

If so, the changeover between DAY mode and NIGHT mode operates the same as selecting 'COLOR' mode.

• The OSD keys do not work for 3 seconds after switching to Color or B/W. This is to ensure a stable camera operation.


26

IMAGE ADJ.

1. When the SETUP menu screen is displayed, select 'IMAGE ADJ.' using


MAIN SETUP

1. LENS

2. EXPOSURE

DC

3. WHITE BAL

4. BACKLIGHT

5. DNR

6. DAY/NIGHT

7. IMAGE ADJ

8. SPECIAL

9. EXIT

ATW

OFF

ON

AUTO


IMAGE SETUP

1. FREEZE OFF

2. V-REV OFF

3. H-REV

4. D-ZOOM

5. SHARPNESS

6. RETURN

OFF

OFF

ON

●

FREEZE : View still pictures.

●

V-REV : Flips the picture vertically on the screen.

●

H-REV : Flips the picture horizontally on the screen.

27


■


●

D-ZOOM : Digitally zooms, the range is x1~x10.

●

SHARPNESS : As this value is increased the picture outline becomes

stronger and clearer.

●

RETURN : Select this to save the settings for the IMAGE ADJ. menu

and to return to the SETUP menu.

Note

• When H-REV or V-REV is selected, any text in the picture also will be flipped horizontally or vertically.

• If the SHARPNESS level is increased too high the picture may become distorted, or noise may generated.


28

SPECIAL

1. When the SETUP menu screen is displayed, select 'SPECIAL' using the

Up and Down buttons.

MAIN SETUP

1. LENS

2. EXPOSURE

DC

3. WHITE BAL

4. BACKLIGHT

5. DNR

6. DAY/NIGHT

7. IMAGE ADJ

ATW

OFF

ON

AUTO

8. SPECIAL

9. EXIT


SPECIAL

1. CAM TITLE

2. SYNC

3. MOTION DET

4. PRIVACY

5. DIS

6. COMM ADJ

7. LANGUAGE

8. RESET

9. RETURN

OFF

INT

OFF

OFF

OFF

ENGLISH

●

CAM TITLE : If a title is entered, the title appears on the monitor.

①

When the SPECIAL menu screen is displayed, use the Up and

Down buttons to point the cursor to 'CAM TITLE'.

29


■


②

Set to 'ON' using the Left and Right buttons.

Note

• When the CAM TITLE menu is

'OFF', no title will be displayed on the monitor screen even if one has been entered.

SPECIAL

1. CAM TITLE

2. SYNC

3. MOTION DET

4. PRIVACY

5. DIS

6. COMM ADJ

7. LANGUAGE

8. RESET

9. RETURN

OFF

INT

OFF

OFF

OFF

ENGLISH

③

Press the SET button.

a n

A

N

b o

.

B

O

C

P c p

D E

Q R

1 d q

2 r e

3 s f

F

S

Camera ID t

4

T g

G H

U

I

V h u

5 i v

6 j w

J

W

7 k x

K L

X Y l

8 y

9 z m

M

Z

→ ←

C L R P O S E N D

④

Use the 4 direction buttons to move to a character and select it by pressing the SET button. Repeat this action to enter multiple characters. Up to 15 alphanumeric characters can be used.

Note

• If the cursor is moved to CLR and the SET button pressed, all letters are deleted. To edit a letter, change the cursor to the bottom left arrow and press the SET button. Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then press the SET button.


30

⑤

Enter a title, move the cursor to 'POS' and press the SET button. The entered title appears on the screen. Select the position to display the title on the screen using the 4 directional buttons and press the SET button.

When the position is determined, select 'END' and press the

SET button to return to the SPECIAL menu.

●

SYNC : In areas where the supply is 60Hz,

synchronise the output phase of

multiple cameras using the power

synchronization function (Line-Lock),

without using a synchronisation signal

generator.

- INT : Internal Synchronisation Type

- L/L : Power Synchronisation Type, Line-lock

• Press the SET button.

• Select a phase between 0 and 359.

Note

• When using AC power at a 60Hz frequency Line-Lock synchronisation can be used.

• When the power is DC 12V, the SYNC. menu is fixed to the 'INT' mode.

●

MOTION DET:

This camera displays an on-screen message whenever motion is detected.

31


■


①

When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the cursor points to MOTION DET.

②

Set up the function using the 4 directional buttons.

- SENSITIVITY : Select up to eight MD areas. When the SENSITIVITY

value is high, motion detection sensitivity is increased to recognise

small movements.

- AREA MODE : Determines whether to use the MD area selected in

SENSITIVITY.

- SEL POS : Determines which of the 4 vertices of each MD area is to

be used.

- YPOS : Determines the co-ordinates of the vertical axis for SEL POS.

- XPOS : Determines the co-ordinates of the horizontal axis for SEL POS.

- FILL→ SET : Fills in a selected MD area. Fills in a selected MD area.

The color of filling is sequentially selected as brown, orange, blue, cyan,

yellowish green, yellow and red.

- RETURN : Select this to save the MOTION DET menu settings and

return to the SPECIAL menu.

Note

• MD areas show only on the MOTION DET menu. Therefore, MD areas are not displayed on the monitor screen.

●

PRIVACY : Hide an area so that it is not

displayed on the monitor.

①

When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the cursor points to 'PRIVACY'.

②

Set up the using the 4 directional buttons.

- AREA SEL : Up to 8 areas are selectable.

- AREA MODE :

Determines whether to use the area selected

in the AREA SEL, and the size and position of

the area.


32

How to Use the Camera ■

- MASK COLOR : Determine area color. Select Grey, Green, Red, Blue,

Black or White.

- TRANSP : Determine the transparency of the selected area, the range

is number from 0 to 3.

- RETURN : Select this to save the PRIVACY menu settings and return to

the SPECIAL menu.

●

DIS (Digital Image Stabiliser) :

This function mitigates picture movement caused by external factors, such as wind.

●

COMM ADJ (Communication Adjustment) :

This function sets up the camera communication status when controlling the camera through an external device.

①

When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the cursor points to 'COMM ADJ'.

②

Set up the mode using the 4 direction buttons.

- CAM ID : Determines the camera's identification number (between 0 and 255).

- BAUD RATE : Select 2400/4800/9600/19200/38400/57600 bps.

- UART MODE : Select NONE, EVEN or ODD for the parity bits.

- RET PKT : Determines whether to send a command back to the controller

device when a communication control command is sent to the camera.

- DISP CAM ID : Display the camera title on the top left corner of the screen.

●

LANGUAGE : Select the appropriate menu language.

●

RESET : Resets the camera settings to the factory defaults.

●

RETURN : Select this to save the SPECIAL menu settings and return to the

SPECIAL menu.

EXIT

Press the SET button in the EXIT menu to save the current settings and exit the SET menu.

33


■

Troubleshooting

If you have trouble operating your camera, refer to the following table.

If the guidelines do not enable you to solve the problem, contact an authorised technician.

Problem Solution

Nothing appears on the screen.

• Check the power connections.

• Check the VIDEO signal line connection.

The image on the screen is not clear.

• Make sure the lens is clean. Clean the lens with a soft clean lint free cloth.

• Adjust the monitor contrast & brightness controls.

• Re-position the camera if necessary.

The image on the screen is dark.

• Adjust the contrast control of the monitor.

• If you have an intermediate device, set the 75 / Hi-z properly.

The camera is not working properly, and the surface of the camera is hot.

• Check that an appropriate power source is connected to the camera.

The DAY/NIGHT menu does not work.

• Check that AGC in the EXPOSURE menu is set to 'OFF'.

The SENS-UP function does not work.

• Check that AGC in the EXPOSURE menu is not set to 'OFF'.

• Check that SHUTTER in the EXPOSURE menu is not set to 'A.FLK' or 'MANUAL'.


34

Problem Solution

The Motion Detection function does not work.

• Check that MOTION DET in the SPECIAL SETUP is not set to 'OFF'.

Color is not correct.

• Check the WHITE BAL settings in the SETUP menu.

The screen flickers continually.

• Check that the camera isn't facing toward a bright luignh. t source, such as the Sun.

35


■

Specifications

Power Source

CCD

Sync

Size

Total Pixels

Effective Pixels

Scanning System

Synchronization

Frequency

NTSC PAL

AC24V / DC12V DC12V AC24V / DC12V DC12V

220mA(AC24V)/260mA(DC12V) 160mA 220mA(AC24V)/260mA(DC12V) 160mA

SONY 1/3" Super HAD High Sensitivity Color CCD

811(H) x 508(V) 795(H) x 596(V)

768(H) x 494(V) 752(H) x 582(V)

2:1 Interlace

Internal / Line Lock

Horizontal : 15.734 KHz, Vertical:59.94 Hz Horizontal : 15.625 KHz, Vertical:50.00 Hz

O.S.D

I

C

T

R

A

L

E

C

E

L

Backlight Comp.

Resolution

S/N (Y signal)

Min. Illumination

White Balance

Electronic Shutter

Speed

Sens-up

Gain Control

DNR

Motion Detection

Privacy

V-REV

H-REV

Freeze

Sharpness

Day & Night

DIS

Digital Zoom

Operating Temperature / Humidity

Storing Temperature / Humidity

Weight

OFF/BLC/HLC

Color : 580 TV Lines B/W : 700 TV Lines

52 dB (AGC Off, Weight ON)

0.15Lux(40IRE Color), 0.0006Lux(40IRE Sense-upX256)

ATW / AWC / Manual / Outdoor / Indoor (1800˚K ~10,500˚K)

1/60 ~ 1/120,000 sec 1/50 ~ 1/120,000 sec

AUTO / OFF (Selectable x2 ~ x256)

LOW / HIGH / OFF

ON / OFF (1~32 Level)

ON / OFF (8 Zone, ALARM Output)

ON/OFF (8 Zone)

ON / OFF

ON / OFF

ON / OFF

ON/OFF (Level Adjustable)

COLOR / Black & White / AUTO / EXT

OFF / ON

OFF / ON(x10)

-10˚C to +50˚C / 30% to 80% RH

-20˚C to +60˚C / 20% to 90% RH

Appro. 350g


36

CE-955-CAM-WD

Clinton Electronics CE-D970 manual

Super DNR High Resolution

Color Dome Camera

Contents

Features

Warning ■

The camera requires periodic inspection.

Stop using your camera when you find it malfunctioning.

Do not Install the camera on a surface that can not support it.

Do not hold plug with wet hands.

Do not dis-assemble the camera.

Do not use the camera close to a gas or oil leak.

Precautions

Components

1. COLOR DOME CAMERA

2. SCREWS

3. WIRE FOR VBS-EXTRA

4. INSTRUCTION GUIDE

Names and Functions of Parts ■

Names and Functions of Parts

Names and Functions of Parts ■

Names and Functions of Parts

Dimensions

Cable Connections

How to Use the Camera

How to Use the Camera ■

On-Screen Display Menu Structure

How to Use the Camera

How to Set up the Functions

LENS

How to Use the Camera

EXPOSURE

How to Use the Camera

White Balance (White Bal.)

How to Use the Camera

BACKLIGHT

How to Use the Camera

DNR

DAY/NIGHT

How to Use the Camera

IMAGE ADJ.

How to Use the Camera

SPECIAL

How to Use the Camera

How to Use the Camera

How to Use the Camera ■

EXIT

Troubleshooting

Specifications

Related manuals

ICRealtime

ICR540CCD

Sony

CAM-90

Genie CCTV

AVRCD-6351

D-MAX

DCC-501DV

Speco Technologies

HT7246IHR

Black

BLK-CDS105NH

Speco Technologies

Intensifier3

Speco Technologies

HT7248FFI

CCTV Center

AP-B9550VRTL

Genie

ID73

Convision

CC-5304 IR