Windsor 115V Operating instructions

Multi-Functional Cleaning

Operating instructions (ENG)

MODELS: CMPS2

10070560

CMPS2E

10070570

86305210-V

11/07/13

Read these instructions before using the machine.

MACHINE DATA LOG/OVERVIEW

Model:

Date of Purchase:

Serial Number:

Sales Representative:

Address:

Phone Number:

The Compass 2

™

OVERVIEW

is a multi-functional cleaning machine intended for commercial use. The water is vacuumed back into the recovery tank. appliance applies chemical at low pressure and uses high pressure to clean with. Then the soiled

2

Warranty Registration

Thank you for purchasing a Windsor product. Warranty registration is quick and easy.

Your registration will allow us to serve you better over the lifetime of the product.

To register your product go to: www.windsorind.com/WarrantyRegistration.aspx

For customer assistance:

1-800-444-7654

CMPS2 86305210

Machine Data Log/Overview.........................2

Table of Contents..........................................3

HOW TO USE THIS MANUAL

How to use this Manual.................................1-1

SAFETY

Important Safety Instructions ........................2-1

Hazard Intensity Level. .................................2-2

Grounding Instructions..................................2-3

Safety Label Location. ..................................2-4

OPERATIONS

Technical Specifications. ..............................3-1

How the Machine Works. ..............................3-2

Components..................................................3-3

Controls.........................................................3-4

Machine Operation........................................3-6

Chemicals .....................................................3-8

MAINTENANCE

Maintenance. ................................................4-1

Strainer....................................................4-2

Vacuum Motor Replacement...................4-3

Solution Pump Replacement...................4-4

Regulating Unloader…………………….. 4-4

Periodic/Daily Maintenance ..........................4-5

Service Schedule. .........................................4-5

Machine Troubleshooting..............................4-6

Notes.............................................................4-7

TABLE OF CONTENTS

GROUP PARTS LIST

Control Panel ................................................ 5-1

Decal............................................................. 5-3

Solution Tank................................................ 5-5

Solution-Injector Assembly ........................... 5-7

Solution-Pump .............................................. 5-9

Recovery Tank............................................ 5-13

Vacuum....................................................... 5-15

Wheels & Frame ........................................ 5-17

Tools – Standard ........................................ 5-19

Wiring – Schematic (120V) ......................... 5-21

Wiring – Schematic (230V) ......................... 5-23

Suggested Spare Parts............................... 5-23

OPTIONS

Vacuum Hose Rack .................................... 6-1

Grout Cleaner ............................................. 6-3

High Pressure Wand................................... 6-5

Carpet Tool ................................................. 6-7

Storage Bag................................................ 6-9

Chemical Lock ............................................ 6-11

Serial Numbers ........................................... 6-13

Warranty

CMPS2 86305210 3

HOW TO USE THIS MANUAL

This manual contains the following sections:

- HOW TO USE THIS MANUAL

- SAFETY

- OPERATIONS

-

MAINTENANCE

-

PARTS LIST

The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.

Parts may be ordered from authorized Windsor dealers.

When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine.

The MACHINE DATA box is located on the inside of the front cover of this manual.

MODEL __________________________________

DATE OF PURCHASE _____________________

SERIAL NUMBER ________________________

SALES REPRESENTATIVE # _______________

The model and serial number of your machine is on the bottom back-end of the machine.

The SAFETY section contains important information regarding hazard or unsafe practices of the machine. Levels of hazards is identified that could result in product or personal injury, or severe injury resulting in death.

The OPERATIONS section is to familiarize the operator with the operation and function of the machine.

The MAINTENANCE section contains preventive maintenance to keep the machine and its components in good working condition. They are listed in this general order:

- Vacuum Motor

- Solution Pump

- Daily Maintenance

- Periodic Maintenance

- Service Schedule

- Machine Troubleshooting

The PARTS LIST section contains assembled parts illustrations and corresponding parts list. The parts lists include a number of columns of information:

- REF – column refers to the reference number on the parts illustration.

- PART NO. – column lists the part number for the part.

- PRV NO. - reference number.

- QTY – column lists the quantity of the part used in that area of the machine.

- DESCRIPTION – column is a brief description of the part.

- SERIAL NO. FROM – If this column has an (*) and a Reference number, see the

SERIAL NUMBERS page in the back of your manual. If column has two asterisk

(**), call manufacturer for serial number.

The serial number indicates the first machine the part number is applicable to. The main illustration shows the most current design of the machine. When a boxed illustration is shown, it displays the older design.

- NOTES – column for information not noted by the other columns.

NOTE: If a service or option kit is installed on your machine, be sure to keep the

KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future

parts.

1-1

CMPS2 86305210

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precaution must always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

This machine is for commercial use.

To reduce the risk of fire, electric shock, or injury:

Connect to a properly grounded outlet. See Grounding Instructions.

Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or service.

Do not allow machine to be used as a toy. Close attention is necessary when used by or near children.

Do not point spray gun at people.

Use only as described in this manual. Use only manufacturer’s recommended components and attachments.

Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center.

Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp edges or corners.

Do not run machine over cord. Keep cord away from heated surfaces.

Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.

Do not handle the electrical plug or machine with wet hands.

Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.

Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

This machine is not suitable for picking up health endangering dust.

Turn off all controls before unplugging.

Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near flammable fluids, dust or vapors.

This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes.

Maintenance and repairs must be done by qualified personnel.

If foam or liquid comes out of machine, switch off immediately.

SAVE THESE INSTRUCTIONS

CMPS2 86305210 2-1

HAZARD INTENSITY LEVEL

The following symbols are used throughout this guide as indicated in their descriptions:

HAZARD INTENSITY LEVEL

There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR

SAFETY. The level of hazard intensity is determined by the following definitions:

WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.

CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.

FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.

Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel.

FOR SAFETY:

DO NOT OPERATE MACHINE:

Unless Trained and Authorized.

Unless Operation Guide is Read and understood.

In Flammable or Explosive areas.

In areas with possible falling objects.

WHEN SERVICING MACHINE:

Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the

. machine. Use Windsor approved replacement parts.

2-2 CMPS2 86305210

THIS PRODUCT IS FOR COMMERCIAL USE

ONLY.

ELECTRICAL:

The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.

EXTENSION CORDS:

If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet (15.5m) in length.

GROUNDING INSTRUCTIONS:

This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

GROUNDING INSTRUCTIONS (120V ONLY)

CMPS2 86305210

GROUNDING INSTRUCTIONS

GROUND-FAULT CIRCUIT-INTERRUPTER

PROTECTION (120V ONLY)

This pressure washer is provided with a

(GFCI) built into the plug of the power supply cord. This device provides additional protection from the risk of electric shock. Should replacement of the plug or cord become necessary, use only identical replacement parts that include GFCI protection. If the GFCI is not the AUTOMATIC RESET TYPE, it must be manually TESTED and RESET each time the cleaning system is plugged in. Press firmly to assure internal spring activates switch. Push

“test“ then push “reset”. Motor will not start if

GFCl does not reset. Check circuit breakers or outlet. If circuit breaker is not tripped and unit will not reset, contact local service center.

2-3

SAFETY LABEL LOCATION

The following WARNING LABEL(S) are found on your cleaning unit. These labels point out important Warnings and Cautions which should be followed at all times. Failure to follow warnings and cautions could result in fatality, personal injury to yourself and/or others, or property damage. Follow these instructions carefully! DO NOT remove these labels.

NOTE: If at any time the labels become illegible, promptly replace them.

WARNING LABEL 86242230

PRV NO. 500009

2-4 CMPS2 86305210

TECHNICAL SPECIFICATIONS

ITEM DIMENSION/CAPACITY

120V, 14A, 60HZ

Electrical

230V, 7A, 50HZ

Electric Pump Motor

Solution Pump

Electric Vacuum Motor

Waterlift

Solution Capacity

1/2hp, 1750rpm

700psi (48 bars), Axial plunger

2stage, 1.25hp (2.80m

3

/min.)

82 in. (208 cm)

29 gallons (111L)

Recovery Capacity

Wheels

- Front (2)

- Rear (2)

Dimensions – Weight

Dimensions – Length

Dimensions - Height

Dimensions - Width

Power Cable

SPECIAL NOTES:

19 gallons (70L)

6 in. dia. (15.24cm) X 1.5

12 in. dia. ( 30.48cm)X 1.75

205 lb. (93kg)

36 in. (91.4cm)

43 in. (109.2cm)

24.75 in. (62.87cm)

50 ft. (127m) 14 gauge

The sound pressure level at 1m from the machine was measured to be 79 dBA. This was a nearfield, broadband measurement taken in a typical industrial environment on a tile floor. This appliance contains no possible source of impact noise. The instantaneous sound pressure is below 63 Pa.

The weighted root mean square acceleration at the operator’s arms was measured to be below

2.5m/s

2

. This was a tri-axial, third-octave-band measurement made during normal operation on a composite tile floor. The measurement and related calculations were made in accordance with

ISO 5349-1.

CMPS2 86305210 3-1

HOW THE MACHINE WORKS

The Compass 2

™

is a multi-functional cleaning machine intended for commercial use. The appliance applies chemical at low pressure and uses high pressure to clean with. Then the soiled water is vacuumed back into the recovery tank.

The machine's primary systems are the clean water system, recovery system, chemical system and pressure washer system.

The function of the clean water system is to store clean water and deliver it to the available tools. The clean water system consists of the clean water tank and strainer. The clean water tank stores water until it is delivered to the tools. The strainer protects the pump from debris.

The function of the recovery system is to vacuum the soiled water back into the recovery tank. The recovery system consists of the wand and wheeled squeegee, vacuum motor, float shut-off and recovery tank. The wand and wheeled squeegee wipes the dirty solution off the floor. The vacuum motor provides suction to draw the dirty solution off the floor and into the recovery tank. The float shut-off protects the vacuum fan from over filling. The recovery tank stores the dirty solution.

The function of the chemical system is to dispense chemical into the clean water system.

The chemical system consists of the chemical reservoir, chemical cap and a chemicalmetering selector. The chemical reservoir stores and dispenses chemical into the clean water system. The chemical-metering selector meters the amount of chemical and selects between chemical A or B and turn chemical off.

The function of pressure washer system is to clean fixtures and other surfaces. The pressure washer system consists of a pump, highpressure hose and spray gun. The pump delivers cleaning solution to the tools. The high-pressure hose connects the pump to the spray gun.

3-2 CMPS2 86305210

COMPONENTS

6

3

2

9

7

1

5

11

8

3. Solution Tank Lid

4. Solution Tank Drain Hose

5. Solution Tank Fill Hose

10

4

7. Recovery Tank Lid

8. Recovery Tank Drain Hose

9. Chemical Siphon Caps

10. Electrical Cord

11. High Pressure Hose Storage

CMPS2 86305210 3-3

CONTROLS

6

8

7

9

3 4

5

2

1

3-4

1. Caster Lock

2. Chemical Selector and Metering Valve

3. Pump Circuit Breaker

4. Pump Switch/Pump Chemical Switch

5. Solution Accessory Tool Hook-Up

6. Vacuum Accessory Tool Hook-Up

7. Vacuum Circuit Breaker

8. Vacuum Switch

9. Main Switch (230V only)

CMPS2 86305210

1. SOLUTION ACCESSORY TOOL HOOK-UP

Used for various auxiliary-cleaning tools.

2. VACUUM ACCESSORY TOOL HOOK-UP

To use accessory tool, remove hose from vac shoe

and attach to accessory tool adaptor.

Turns the vacuum motor On and Off.

High pressure no chemical, low pressure with chemical.

5. CHEMICAL SELECTOR AND METERING VALVE

Meters the amount of chemical being dispensed and selects between chemical A or B and turns chemical off.

Locks the wheels in place to keep the machine from moving.

7. VACUUM CIRCUIT BREAKER

10 Amp. Protects the vacuum motor.

8. PUMP CIRCUIT BREAKER

8 Amp. Protects the pump motor.

Power on and off switch 230V (ONLY).

CMPS2 86305210

CONTROLS

3-5

OPERATIONS

FILLING THE MACHINE

NOTE:Do not put defoamer, solvents spotter or prespray chemicals in the solution tank.

1. Always use gloves and eye protection. Never spray solution towards people.

2. To fill Use fill hose or pour directly into solution tank. Use COLD WATER. Add 1 ½ oz of

CompassRinse

TM to each full solution tank.

3-6 CMPS2 86305210

3. Attach the adapter cap and intake hose to the

Compass 2

TM

Chemical bottle. Refer to the

Compass 2

TM

Chemical Label for the desired dilution.

Compass 2

TM machine in the door way, lock front casters. Start at furthest point in the room and work towards the door.

5. Always Spray chemical using low pressure.

6. Use brush or grout tool for heavy soiled areas.

CMPS2 86305210

OPERATIONS

7. Turn Chemical off. Pressure clean by rinsing surfaces at high pressure.

8. Use Squeegee or Gulper tool to remove standing water.

3-7

OPERATIONS

9. Store and secure hoses and tools neatly.

10. Drain machine at proper disposal areas. Use pressure gun to rinse and clean recovery tank.

UNLOADER

VALVE

11. From the factory your Compass 2 is set to spray at 600 psi (high pressure) and 200 psi (low pressure w/chemical injection). To lower pressure turn the unloader valve knob counter clockwise. The valve is accessed from below the machine through a hole in the bottom frame.

Only turn the valve a maximum of three revolutions.

Note: Lowering the pressure in this way will reduce both of the high pressure and low pressure setting simultaneously.

3-8 CMPS2 86305210

Care must be exercised in the use of all chemicals. Chemicals are poisonous and can pose a health risk. Read and follow manfacturers instructions regarding dangers and correct usages.

The internal parts of the pump used in the machine are suitable for use with most carpet cleaning chemicals. But they are susceptible to chemical attack from some cleaning substances, such as hydrocarbon solvents and chlorinated bleaches. These non-compatible materials are not of the type used for carpet cleaning.

CHEMICALS

Suitable Chemicals

Alkalis

Detergents

Hydroxides

Soaps

Vinegar

Non-Compatible

Aldehydes

Aromatics Hydrocarbons

SP Butyls

Carbon Tetrachloride

Clorox*

Chlorinated Bleaches

Chlorinated Hydrocarbons

Lysol*

Methyl Ethel Ketone (MEK)

Perchorethylene (perc)

Phenolics

Trichlorethylene

D-Limonene

Only use chemicals approved for use with this machine. Use of non-compatible chemicals may cause machine damage and will not be covered under the warranty. Carefully read ingredients on manfacturer’s label before using any product in this machine.

Do not let pump run dry.

Do not let pump run unattended.

CMPS2 86305210

OPERATIONS

3-9

NOTES:

3-10 CMPS2 86305210

4

7

2. Strainer

1

3

MAINTENANCE

5

2

6

5. Pump

7. Injector Assembly & Coil

CMPS2 86305210 4-1

MAINTENANCE

The float shut-off is located inside the recovery tank. The purpose of the float shut-off is to notify the user that the recovery tank is full. Remove daily and clean any debris for maximum airflow.

2. STRAINER

The strainer is located on the left side between the front and rear wheels. The strainer protects the pump from debris. If there is little or no solution flow to the ground, check the stainer for debris. Drain the solution tank and clean the solution strainer. To remove the strainer, turn the bottom part of the strainer counterclockwise until the bottom is separated. Clean out the debris from the wire mesh and reassemble.

Make sure the o-ring gasket is in place when reassembled.

Circuit breakers interrupt the flow of power in the event of an electrical overload. When a circuit breaker is tripped, reset it by pressing the exposed button. If a circuit breaker continues to trip, the cause of the electrical overload should be found and corrected.

10 AMP

VACUUM MOTOR

8 AMP

PUMP MOTOR

120V

7 AMP

VACUUM MOTOR

5 AMP

PUMP MOTOR

230V

4-2 CMPS2 86305210

MAINTENANCE

(Refer to vacuum group in the parts section of manual).

ONLY QUALIFIED MAINTENANCE PERSONNEL

ARE TO PERFORM THE FOLLOWING REPAIRS.

VACUUM MOTOR REPLACEMENT

1. Turn off all switches and unplug machine.

2. Remove recovery tank.

3. Remove the 5 screws holding the vacuum motor cover to the solution tank.

4. Locate the vacuum motor wires and disconnect at the connector.

5. Remove the vacuum motor.

6. Reverse process to install.

Vacuum Motor Carbon Brushes Replacement (Windsor)

End Cap

Carbon

Brushes

WARNING: The green ground wire must be attached for safe operation.

See wiring diagram.

If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center.

Important:

These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.

3

8

[9.5mm]

Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long.

CMPS2 86305210 4-3

MAINTENANCE

5. PUMP

ONLY QUALIFIED MAINTENANCE

PERSONNEL ARE TO PERFORM THE

FOLLOWING REPAIRS.

SOLUTION PUMP REPLACEMENT


2. Tilt machine back so bottom is exposed.

3. Remove the 6 screws that fasten the frame to the solution tank.

4. Remove the solution hoses from the fittings on the pump.


6. REGULATING UNLOADER

ONLY QUALIFIED MAINTENANCE

PERSONNEL ARE TO PERFORM THE

FOLLOWING REPAIRS.

UNLOADER REPLACEMENT


2. Tilt machine back so bottom is exposed.

3. Remove the 6 screws that fasten the frame

to the solution tank.

4. Remove the solution hoses from the fittings

on the pump.

5. Remove the unloader.


PUMP REPLACEMENT KITS

CAM & BEARING

86311080 120V

86305510 230V

VALVE & O-RING KIT

(BOTH SIDES)

86201030

PRV NO. 250-73B

PLUNGER & SEALS KIT

86201080

PRV NO. 250-25A

4-4 CMPS2 86305210

PERIODIC MAINTENACE

Twice a month, flush a white vinegar solution (one quart vinegar to two gallons of water) or antibrowning solution (mixed as directed) through the machine. This will prevent build-up of alkaline residue in the system. If spray jets become clogged, remove the spray tips, wash them thoroughly, and blow dry.

NOTE: Do not use pins, wires, etc. to clean nozzles as this could destroy the spray pattern.

Periodically inspect all hoses, electrical cables and connections on your machine. Frayed or cracked hoses should be repaired or replaced to eliminate vacuum or solution pressure loss. The electrical cable must be well insulated and cable connector screw kept tight. If the cable insulation is broken or frayed, repair or replace immediately. Don’t take chances with elctrical fire or shock.

SERVICE SCHEDULE

Check machine for cord damage

Check recovery dome and gasket for damage and cleanliness

Check hoses for wear, blockages, or damage

Check handles, switches, and knobs for damage

Check vac motor intake filter and clean

Run one gallon of water through system

MAINTENANCE

DAILY/REGULAR MAINTENANCE

Before making any adjustments to the machine, disconnect the power cord from the electrical source.

1. Empty unused cleaning solution from the solution tank.

2. Inspect and clean filter screen in solution tank.

3. Flush pumping system with 4 to 7 liters of clean water.

4. After each use, rinse tank with fresh water.

Periodically inspect the recovery tank and decontaminate if necessary, using a Hospital

Grade Virucide or a 10-1 bleach to water solution. Waste water should be disposed of properly.

5. Remove filter to clean. Filters used for wet pickup including striper must be thoroughly cleaned before being allowed to dry.

6. Check spray jets for full spray pattern.

*

*

*

*

*

*

Clean out recovery tank and check float valve to make sure it moves freely

Clean out solution tank and remove and clean vacuum intake screen

Clean outside of all tanks and check for damage

Run vac motor for at least one minute to allow motor to dry

Store with dome off tank to allow the tank to dry

Check all bearings for noise

Check all gaskets for wear and leakage

Check vacuum intake screen for damage; replace if necessary

Check pump pressure; observe spray pattern and check with gauge if necessary

Check and clean solution screen

Check cables for fraying

Check overall performance of machine

Check vac motor carbon brushes

*

*

*

*

*

*

*

*

*

*

*

*

*

CMPS2 86305210 4-5

TROUBLESHOOTING

PROBLEM

Loss of Power

Electrical shock

Vac motor speed varies or doesn’t run

Loss of vacuum

Pump runs no solution

Pump runs, loss of pressure

Pump will not run

Solution hose fitting hard to connect

CAUSE SOLUTION

Dead electrical circuit

Faulty power cord

GFCI breaker is tripped

Check building circuit breaker or fuse box.

Replace

Reset breaker on power cord

Equipment not grounding Follow grounding instructions exactly

Receptacle not grounded Contact an electrician to check building’s wiring

Internal wiring problem

Have a trained service technician check machine’s wiring

Worn motor brushes

Motor worn out

Faulty switch

Loose vacuum dome

Replace

Replace

Replace

Center and seal dome over tank

Vacuum circuit breaker tripped.

Reset breaker.

Crack in dome of poor joint Replace or repair using acrylic plastic cement only

Lint or dirt clogging vacuum screen

With power off clean screen

Loose cuffs on vacuum hose

Vac motor seals leaking

Floor tool vac chamber clogged

Vac motor, hose, or dome gasket

Tighten cuffs turning counterclockwise

Replace

Wash out with hose. Pick lint out with a wire

Replace

Pump inlet screen plugged Clean inlet screen

Pump circuit breaker tripped.

Reset breaker.

Faulty pump switch.

Faulty pump motor.

Pump air locked

Call for service.

Call for service.

Press trigger to open valve on cleaning wand to relieve air

Internal or external solution line damaged and leaking

Jet orifice on cleaning wand is to large

Internal pump components wearing out

Replace

Total jet opening for 100 psi should be .06 to .08

Replace, see pump kit components (pg 4-3)

Note: Operation of pump using a wand or hand tool with an orifice of less than .06 will cause pump to cavitate or pulsate and could result in premature wear of pump components.

Check valves in pump head for particles or cuts in seals

Unit not plugged in

Loose wiring

Corrosion on fittings.

Take piston from BPR and lubricate with Superlube.

If problem still exists change BPR kit

Connect unit to 3 prong grounded outlet

See dealer

Clean with steel wool. Soak in acetic acid (white vinegar). Lubricate lightly with silicone base lubricant.

4-6 CMPS2 86305210

NOTES:

CMPS2 86305210

4-7

CONTROL PANEL

1

17 16 11

14

18

4 13

12A

12B

11

15

5

11 7A

7B

6A

6B

10

9

8

4

1

2

3

5-1 CMPS2 86305210

CONTROL PANEL

REF PART NO.

8 86302400

16

17

18

86238030

86007140

86310280

PRV NO. QTY

-

9 86197390 31021

10 86279560 87178

11 86276290 70626

12A 86297370 -

12B 86302150 -

13 86002450 22015

14 86002010 14942

15 86007200 72162

36235

72130

-

DESCRIPTION

1 86233090 20016

2 86282280 39634

3 86232110 270699

4 86258930 84187

3

2

2

1

CLAMP, 1/4 ID HOSE

HOSE, 1/4 ID NYLOCBRAID X 23”

CAMP CHEM FEED W/DIP TUBE

VALVE, CHEMICAL METERING

5 86005700 57104 2 NUT, 10-32 W/STAR WASHER PLTD

6A 86001940 14635 1 BREAKER, 10A CIRUIT

1

1

3

4

QD, NIPPLE, FOSTER 25 MPB

ELBOW, 1/4 NPT 45D STREET

WASHER, 5/8 ID X 1.70 D 0.05T

SCR, #10 X 3/4 PPHST HI-LO BLK

1 PANEL, 3 SWITCH CONTROL

1 COUPLER, 1/4 QD

2 BOOT, 3/8 CIRCUIT BREAKER

1 SWITCH, DPDT3-POSITION ROCKER

2 GASKET, SWITCH CARLING

1 SWITCH, SPST 2-POSITION ROCKER

1 SWITCH, DPST 2 POSITION ROCKER

SERIAL NO.

FROM

NOTES:

120V

230V

120V

230V

120V

230V

230V ONLY

CMPS2 86305210

5-2

DECAL

5-3

3

6

5

7

4

CMPS2 86305210

1

2

8

DECAL

REF PART NO. PRV NO. QTY DESCRIPTION

1 86299520 -

LABEL, WINDSOR COMPASS,

CONTROL

2

3

86302660

86302650

-

-

1

1

LABEL, LEFT, COMPASS2

LABEL, RIGHT, COMPASS2

4

5

86004970

86305190

50990

-

1 LABEL, WINDSOR LOGO DOMED

1 INSTRUCTION CARD, CMPS2

6 86002870 27417 1 CORD, 1/8” X 12”

LABEL, WARNING EXPLOSION

7 86242230 500009 1

HAZ’D

8 86303660 - 1 LABEL, COMPASS, 230V, ON/OFF

SERIAL NO.

FROM

NOTES:

CMPS2 86305210

5-4

SOLUTION TANK

14

15

16

5

13

12

11

10

15

19

18

17

25

23

1

3

26

24

22

9

4

5

8

5

6

7

2

1

20

21

5-5 CMPS2 86305210

SOLUTION TANK

REF

1

PART NO.

86275800

PRV NO.

70546

QTY DESCRIPTION

5 SCR, 8 X 3/4 PFHT/S BLK ZINC

3

4

5

6

86336450

86239680

86006950

86224730

7

8

86276650

86218960

9 86301030

10 86302130

-

41476

70532

73939

70707

41575

-

-

11 86302090

12 86002990

-

27744

13 86301990 -

14 86301980 -

15 86276290

16 86271680

17 86197920

18 86260690

70626

57236

40023

02130

19 86302590

20 86233300

21 86197910

22 86339990

23 86277560

24 86232790

25 86272020

26 86336230

-

20101

40022

-

70866

27912

57313

-

1 TANK, SOL, CMPS2

1 HOOK, HOSE STORAGE

4 SCR, 10-32 X 1/2 PPHMS BLK NP

1 SPRING, COMP, 12MM OD X 12.7MM

1 SCR, 5/16-18 X 1.5 BSHCS SS

1 HOOK, UPPER, CORD

1 PLATE, DETENT, CORD HOOK

2 CLIP, C 5/8, PLASTIC

10

3

1

SCR, 8-32 X 7/16 PFHTC “F” BLK

CLIP, 1 1/2” PLASTIC

HOSE HOOK, HLDER, TOOL

8 SCR, #10 X 3/4 PPHST HI-LO BLK

1 NUT, 10-32 HEX NYLOCK BLK

1 HOSEBARB, 1/2MPT X 3/8 NYL DL

1 HOSE ASM, FCT ADPTR X 60" NBRD

1 HOSE, CLEAR, 3/4 ID X 30”

1 CLAMP, 1.25” WORM GEAR SS

1 HOSEBARB, 1/2MPT X 1/2 POLY DL

1 SCR, 8-32 X 1.0, FHMS, PHLPS, SS, BLK

1 SCR,#6X1/2 SHT MTL SS

1 CHAIN, ASM, #10SS BD X 8"

1 NUT, 8-32 HEX THIN NYLOCK SS

1 DECK PLATE ASM, 4" BLK

- 86300320 -

* SEE SERIAL NUMBER PAGE.

1 TANK, SOL CMPS 2

SERIAL NO.

FROM

*(1)

NOTES:

*(1)

*(1)

*(1)

*(1)

*(1)

INCLUDES

ITEMS 1, 26

CMPS2 86305210

5-6

SOLUTION-INJECTOR ASSEMBLY

1

5-7

24

2

4

23

1

3

21

1

16

17

15

18

14

27

21

5

13

12

28

6A

6B

7

24

27

20

19

8

29

30

25

26

22

3

4

7

10

9

11

CMPS2 86305210

SOLUTION - INJECTOR ASSEMBLY


1

2

3

4

86302410

86302570

86197760

86247680

5 86303760

6A 86303850

6B 86308530

7 86197300

8

9

86303770

86305750

10 86303750

11 86197370

12 86006630

13 86010650

14

15

16

17

86006490

86305200

86273980

86302400

-

-

78308

56015

-

-

-

14079

-

-

-

31017

70171

87018

70013

-

70066

-

18 86005700 57104

3

1

2

2

1

QD, COUPLER, FOSTER 25FS

HOSE, PULSE, 3/8F X 3/8F X 45”

TEE, 1/4 STREET

NIPPLE, 1/4 HEX

VALVE, SOLENOID, 1/4F 700PSI

1 COIL, 230V, SOLENOID, CMPS2

1 BUSHING, 1/8 FPT X 1/4 MPT HEX

1

1

1

1

2

2

INJECTOR KIT, DEMA, 200-3C

NIPPLE, 1/4 X 1/8 REDUCING HEX

HOSE, ASM, 1/4F X 1/4M, 7”

ELBOW, 1/4FPT X 1/4FPT

SCR, 10-24 X 1/2 HHMS SS

WASHER, #10 X 9/16 OD

2 SCR, 8-32 X 3/4 PPHMS

1 TERMINAL BLOCK, 115/230V

2 SCR, 10-32 X 3/4 PPHMS

1 QD, NIPPLE, FOSTER 25MPB

4

NUT, 10-32 W/STAR WASHER PLTD

19 86233090

20 86295830

23 86302790

20016

-

-

1 CLAMP, 1/4 ID HOSE

1 HOSE, 1/4ID NYLOBRAID X 41”

21 86264940 27051 6 CABLE

22 86197290 14076 1 BUSHING, 3/8 MPT X 1/4 FPT HEX

1

HOSE, PULSE, 1/4 MPLT X 1/4

MPLT X 30”

24 86188130 11-800151 2 NIPPLE, 3/8M X 1/4M

25 86264940 27051 1 CABLE

26 86308560

27 86197730

-

78024

1 ASM, FILTER MAIN

2 TEE, 1/4 BRANCH

28 86180460 12-800356 1 ELL,1/4PX1/4T 45DEG BR

29 86180420 12-800261 1 ELL, 1/8P X 1/4T 45 DEG.

30 86327120 - 1 HOSE, 3/16 X 8 (1/4FT BS) MET

SERIAL NO.

FROM

NOTES:

*

*

*

*

230V ONLY

CMPS2 86305210

5-8

SOLUTION-PUMP

8

9

10

15

1

2

16

14

3

4

15

5A

5B

7

12

6

13

11

5-9

CMPS2 86305210

SOLUTION-PUMP


1 86302790

2 86197610

3 86233090

4 86302780

-

40034

20016

-

1

HOSE, PULSE, 1/4MSWL X 3/8NPT X

30”

1 HOSEBARB, 3/8MPTX3/8 90D DL


1 HOSE, BRAIDED, 3/8ID X 16” L

5A 86302820

5B 86308100

-

-

1 PUMP, PUMPTEC, 700PSI

1 PUMP, PUMPTEC, 700PSI, 230V

6 86317550 - 1 HOSEBARB, 3/8 MPT X 1/2 90 BR

7 86190520 11-800224 4 PLUG, 3/8 SOCHD BR

8 86005590

9 86197370

10 86302400

11 86240280

12 86233150

13 86302720

56014

31017

-

39711

20042

-

1

1

1

1

1

1

NIPPLE, 1/4 CLOSE

ELBOW, 1/4FPT X 1/4FPT

QD, NIPPLE, FOSTER 25MPB

HOSE, 1/2ID WIRE BOUND X 8"

CLAMP, 3/8 HOSE (D-SLOT)

MOTOR, 700PSI, 115/230 VOLT

14 86302730

15 86302410

16 86197380

-

-

31018

1 UNLOADER, 800PSI, PUMPTEC

2 QD, COUPLER, FOSTER 25FS

1 ELBOW, 3/8FPT X 1/4FPT

SERIAL NO.

FROM

NOTES:

CMPS2 86305210

5-10

SOLUTION-PUMP

6

5

7A

7B

2

1

8

10

9

3

4

5-11

CMPS2 86305210

REF PART NO. PRV NO. QTY

2

3

4

5

86233090

86197910

86233150

86010630

6 86005810

7A 86302430

7B 86307960

9 86302770

10 86340870

20016

40022

20042

87013

57245

-

-

-

-

DESCRIPTION


1 HOSEBARB, 1/2MPT X 1/2 POLY DL

3 CLAMP, 3/8 HOSE (D-SLOT)

5 WASHER, 1/4 ID X 5/8 OD SS

5 NUT, 1/4-20 HEX NYLOCK SS

1 PUMP ASM, 700 PSI 115V

1 PUMP ASM, 700 230V CMPS2

CABLE UL/CSA

1 HOSE, 1/2 ID WIRE BOUND X 14" L

1 STRAINER 1/2" HOSE 80 MESH

SOLUTION-PUMP

SERIAL NO.

FROM

NOTES:

COMPLETE

COMPLETE

CMPS2 86305210

5-12

RECOVERY TANK

12

14

13

15

1

11

1

2

16

9

8

7

10

20

6

19

5

18

17

3

4

2

1

5-13 CMPS2 86305210

RECOVERY TANK

REF PART NO.

1 86277040

2 86010670

5

6

7

86275800

86004000

86033250

PRV NO.

70781

87029

3 86070510 140659

70546

35255

66402

QTY DESCRIPTION

11 SCR, 5/16-18 X 1/2 HHCS SS NP

11 WASHER, 5/16 FLAT SS

1 BRKT, TANK MOUNT

6

1

1

SCR, 8 X 3/4 PFHT/S BLK ZINC

GASKET, TANK LID

PIPE ASM, VACUUM STACK

9

10

11

12

86233110

86300900

86271850

86296560

20018

-

57287

-

1 CLAMP, 1.0” WORM GEAR

1 TANK, REC DK GRY 2

1 NUT, 1/2 NPT PLASTIC

1 BRACKET, UTILITY MOUNT, 2.0

1 HOSEBARB, 1/2 MPT X 3/4 90D 13 86240790 82358

14 86302360 -

15 86177050 03-000176 1 CLAMP, HOSE #20

16 86302590 - 1 HOSE, CLEAR, 3/4ID X 34”

17 86277560

18 86339990

19 86232790

20 86272020

70866

-

27912

57313

1

1

1

1

SCR, #6 X 1/2 SHT MTL SS

SCR, 8-32 X 1.0, FHMS, PHLPS, SS, BLK

CHAIN, ASM, #10SS BD X 8"

NUT, 8-32 HEX THIN NYLOCK SS

SERIAL NO.

FROM

NOTES:

CMPS2 86305210

5-14

Vacuum

15

14

11

12

10

12

7

5

4

9A

9B

12

8

6

13A

13B 1

16A

16B

2

3

40 86305210 COMPASS 2

Vacuum

REF PART NO.

PRV NO.

QTY

7

8

5

6

3

4

1

2

86237870

86002380

86281180

86240240

86233260

86274370

86005810

86010640

35270

20046

39298

39697

20092

70191

57245

87016

9A 86201970 065-92

9B 86201950 065-24E

10 86003760

11 86296140

35166

-

12 86010630

13A 86007010

13B 86276720

14 86010670

87013

70663

70718

87029

15 86277040

16A 86303840

70781

-

86135320 140687

16B 86202080 -

86135330 -

DESCRIPTION

1 GASKET, 5.0 OD X 2.38 ID X .25T

1 CLAMP, 2.25" WORM GEAR

1 HOSE, 2.0 VAC EXHAUST X 17”

1 HOSE, 3.15 ID X 7.0L VENT

1 CLAMP, 3.5" WORM GEAR

1 SCR, 10-24 X 1/2 HHTC TYPE 23

3 NUT, 1/4-20 HEX NYLOCK SS

1 WASHER, #10 LOCK EXT STAR SS

3 VAC SPACER 2 1/4 (2 STAGE)

3 VAC SPACER 3 1/8

1 GASKET, VAC MTR

1 COVER, VAC MOTOR

9 WASHER, 1/4 ID X 5/8 OD SS

3 SCR, 1/4-20 X 3 1/4 HHCS PLT

3 SCR, 1/4-20 X 4.25 HHCS PLTD

5 WASHER, 5/16 FLAT SS

5 SCR, 5/16-18 X 1/2 HHCS SS NP

1 VAC MTR, 120V 5.7 2 ST TD

BRUSH SET, 120V VAC WINDSOR

1 VACUUM 116859-13 220V SM 3 STG

BRUSH SET, 230V VAC MTR

SERIAL NO.

FROM

NOTES:

115V

230V

115V

230V

115V

115V

230V

230V

86305210 COMPASS 2 41

WHEELS & FRAME

5

6

7

5

3

4

5-17

9

5

8

1

10 11

2

CMPS2 86305210


4

5

6

7

1 86323840 - 2 12”

2

3

86271380

86270830

57196

57023

2

8

NUT, 1/2 PUSH-IN DOME CAP

NUT, 5/16-18 HEX NYLOCK SS

86078800 620001

86010670

86276780

86232620

87029

70728

18043

1

16

4

2

PLATE MOUNT CASTER

WASHER, 5/16 FLAT SS

SCR, 5/16-18 X 3/4 HHCS SS

CASTER, 6” DIA X 4.63 SWIVEL

8 86277040 70781 4 SCR, 5/16-18X1/2 HHCS SS NP

9 86296130 - 1

10 86323860

11 86219480

-

-

4 BUSHING FLANGED .501D X .630D

2 HUBCAP 9.75” WHEEL GREY

WHEELS & FRAME

SERIAL NO.

FROM

NOTES:

CMPS2 86305210

5-18

TOOLS- STANDARD

1

5-19

5

4

13A

13B

6

17

20

10

9

8

7

CMPS2 86305210

11

3

2

16

TOOLS- STANDARD

REF

1

2

PART NO.

86257660

86257650

PRV NO. QTY

02478

02477

DESCRIPTION

1 TOOL, HAND SQUEEGEE

1 TOOL, SCRUB BRUSH HANDLE

4 86257670 02479 1 TOOL, TILE BRUSH

6

7

8

9

86257620

86301890

86290390

86301910

10 86301920

11 86005580

12 86200350

13A 86240180

02473

-

-

-

-

56012

39578

39637

1 TOOL, WHEELED SQUEEGEE

1 LANCE, TUBE, 1/4”, 14” LONG

1 GUN, PRESSURE WASH PMPTC

1 BUSHING, SPRAY GUN

1 NOZZLE, ADJUSTABLE, 027 JET

1 NIPPLE, 1/4 FPT QD

1 HOSE ASM, 1/4HP SLTN 25 FT

1 HOSE ASM, 1.5 X 30 FT

13B 86240250 39703

14 86202160 320-05

1 HOSE ASM, 1.5 BLK VAC X 30’

1 STRAP, VELCRO

15 86234200 23215 1 CORD SET, 14/3 X 50 FT GFCI YLW

16 86301880 - 1 SPRAY

17 86002400 20064

18 86241930 47419

19 86290410

20 86257690

-

02481

1 CLAMP, 2.9” WORM GEAR X .312W

- KIT, SQUEEGEE TOOL BLADES

- NOZZLE REPLACEMENT JET

1 TOOL, DOOR WEDGE

SERIAL NO.

FROM

NOTES:

NOT SHOWN

NOT SHOWN

NOT SHOWN

COMPLETE

CMPS2 86305210

5-20

WIRING – SCHEMATIC – 120V

7 2

POWER

CORD

POWER

GRN/YEL

WHT

BLK

POWER

CORD

CONNECTION

BLK

BLU

RED

ORG

1

5

2

6

3

7

4

8

WHT

9 10 11 12

13 14 15 16

WHT

WHT

PUMP

MOTOR

5-21

1

VACUUM

MOTOR

6

SOLENOID

GRN/YEL

GRN/YEL

5 WIRE HARNESS

GRN/YEL

ORG

BLU

RED

BLK

5

BLK

VACUUM

SWITCH

VACUUM

CIRCUIT

BREAKER

3

PUMP

CIRCUIT

BREAKER

5 4

BLK

PUMP

SWITCH

4

CMPS2 86305210

WIRING DIAGRAM - 120V

REF PART NO. PRV NO. QTY

1 86305020 - 1 MAIN

2 86305060 - 1 CORD SET, 14/3 X 31

3 86308000

4

5

6

7

88305070

86268570

86268180

86234200

-

-

88401

88184

23215

1 WIRE, 6” BLK/14 76050 X 76029

2

2

1

1

DESCRIPTION

WIRE, 2”, BLK/14 76050 X 76029

WIRE, 3”, BLK/14 76029X 76029

WIRE, 8”, GRN/18 76008 X 76008

CORD SET, 14/3X50’ GFCI YLW

SERIAL NO.

FROM

NOTES:

CMPS2 86305210

5-22

WIRING – SCHEMATIC – 230V

1 POWER

BRN

GRN/YEL

BRN

BLU BLU

EMI

FILTER

WHT

BLK

WHT/BLK POWER

CORD

BLU

BLK

WHT

RED

ORG

GRB/YEL

1

5

2

6

3

7

4

8

BLK

9 10 11 12

13 14 15 16

WHT

WHT

PUMP

MOTOR

5-23

2

VACUUM

MOTOR

3

SOLENOID

GRN/YEL

GRN/YEL

7 WIRE HARNESS

GRN/YEL

ORG

WHT

BLK

BLU

RED

BLK

4

5

VACUUM

SWITCH

4 5

BLK

WHT/BLK

BLK

VACUUM

CIRCUIT

BREAKER

ON

OFF

PUMP

CIRCUIT

BREAKER

4

5

PUMP

SWITCH

CMPS2 86305210

WIRING DIAGRAM – 230V

REF PART NO.

1

2

3

4

5

86234330

86308770

86268180

86308750

86308760

PRV NO. QTY

23711

-

88184

-

-

DESCRIPTION

1 CORD ASM, 1.5MM2X 50’ EURO

1 HARNESS, MAIN, 230V

1 WIRE, 8" GRN/18 76008 X 76008

3 WIRE, 4”, BLK/14 76029 X 76029

3 WIRE, 4”, BLK/14 76050 X 76029

SERIAL NO.

FROM

NOTES:

PART NO. PRV NO. DESCRIPTION

86241930

86305460

86135320

86028720

47419 KIT, SQUEEGEE BLADES, WHEELS & SCREWS

- STRAINER, 3/8FPT 80 MESH

140687 BRUSH SET, 120V VAC

53266 VAC MOTOR ASM, 115V W/ TERM

86304640

86135330

-

-

ASSY, VAC MOTOR, 230V

BRUSH SET, 230V VAC MTR

86002010 14942 BOOT, 3/8 CIRCUIT BREAKER

86215670 140839

86001940 14635 BREAKER, 10A CIRCUIT

86230200

86230110

14831

14312

BREAKER, 5A VDE CIRCUIT

BREAKER, 7A, CIRCUIT

86302720 - MOTOR, 700PSI, PUMPTEC

86302820

86308100

-

-

PUMP, PUMPTEC, 700PSI

PUMP, PUMPTEC, 700PSI, 230V

- NOZZLE, ADJUSTABLE, 027 JET 86301920

SUGGESTED SPARE PARTS

SERIAL NO.

FROM

NOTES:

115V

115V

230V

230V

115V

115V

230V

230V

230V

115V

230V

CMPS2 86305210 5-24

VAC HOSE RACK - OPTION

1

3

4

7

2

5

6

6-1 CMPS2 86305210

2

3

4

5

6

7

REF PART NO.

86276600

86006590

86275210

86270250

86005680

86068180

VAC HOSE RACK - OPTION

PRV NO.

70696

70088

70384

03-000133

57047

140710

QTY DESCRIPTION

3 SCR, #10 X 3/4 PTHSMS SS

2 SCR, 10-32 X 1/2 PPHMS SS NP

2 SCR, 1/4-20 X ½ PHTR BLK DL

2 CLAMP, 1/4X1/4 BLT VIN DP

2 NUT, ¼-20 HEX NYLOCK

1 BRACKET, TOP HOSE RACK

SERIAL NO.

FROM

NOTES:

CMPS2 86305210

6-2

TOOLS- GROUT CLEANER-OPTION

6-3 CMPS2 86305210

TOOLS – GROUT CLEANER-OPTION

REF

5

6

7

8

1

2

3

4

PART NO.

86200820

86247720

86194160

86240190

86090230

86241700

86006590

86088740

9 86308040

10 86270990

11 86308780

12 86006870

PRV NO.

270-11A

56032

11-800133

39639

87015

44079

70088

02476

-

57090

-

70406

QTY DESCRIPTION

1 NIPPLE, 1/8 FPT QD MALE BRASS

1 NIPPLE, 1/8 CLOSE

1 TEE, 1/8 BR

2 HOSE, 1/8 MPT X 1/4 FPT X 12L

4 WASHER, 9/16 ID X 1.06 OD SS

2 JET, 1/4 MEG 15015

4 SCR, 10-32 X 1/2 PPHMS SS NP

1 TOOL, GROUT CLEANER

2 BRUSH, FLOOR TOOL

4 NUT, 10-32 HEX NYLOCK SS

2 BRKT, BRUSH MOUNT

4 SCREW #10B X 1/2 PHSM BLK

SERIAL NO.

FROM

NOTES:

CMPS2 86305210

6-4

TOOLS- HIGH PRESSURE WAND-OPTION

6-5 CMPS2 86305210

REF

1

2

3

4

5

6

8

10

PART NO.

86005580

86240210

86274410

86258950

86240200

86200810

86270990

86135760

TOOLS – HIGH PRESSURE WAND-OPTION

PRV NO. QTY

56012

39641

70195

84189

39640

270-11

DESCRIPTION

1 NIPPLE, 1/4 FPT QD

1 HOSE, 1/8 MPT X 1/4 MPT X 7 L

1 SCR, 10-32 X 1.25 PPHMS SS

1 VALVE, 500 PSI W/ CLAMP

1 HOSE, 1/8 MPT X 1/8 MPT X 38L

1 NIPPLE, 1/8 FPT QD FEM BRASS

57090

38109

1

1

NUT, 10-32 HEX NYLOCK SS

KIT, PRESSURE WAND

HANDLE GRIP ASSEMBLY 1.5”T

SERIAL NO.

FROM

NOTES:

COMPLETE

CMPS2 86305210

6-6

TOOLS- CARPET TOOL- OPTION

6-7

7

3

2

1

CMPS2 86305210

4

5

6

TOOLS – CARPET TOOL- OPTION


1

2

86200820 270-11A 1 NIPPLE, 1/8 FPT QD MALE BRASS

86240220 39642 1 HOSE, 1/8 MPT X 1/8 MPT

3 86296220 - 1 ELBOW, 1/8 FPT

4 86305440 -

WASHER, .45ID X .87X .20THK

NYL

WASHER, .40ID X .87OD X

5 86305450 - 1

.060THK SST

6

7

86241710

86284550

44080

02484

1

-

JET, 1/4 H-VV 11003

TOOL, CARPET CLEANER

SERIAL NO.

FROM

NOTES:

COMPLETE

CMPS2 86305210

6-8

STORAGE BAG-OPTION

6-9 CMPS2 86305210

REF

1

PART NO.

86283390

PRV NO. QTY

47423 1

DESCRIPTION

KIT, STORAGE BAG

STORAGE BAG-OPTION

SERIAL NO.

FROM

NOTES:

CMPS2 86305210

6-10

CHEMICAL LOCK-OPTION

6-11 CMPS2 86305210

REF PART NO.

1 86070520

PRV NO. QTY

140660 1

DESCRIPTION

BRKT, CHEMICAL LOCK

CHEMICAL LOCK-OPTION

SERIAL NO.

FROM

NOTES:

CMPS2 86305210

6-12

REF.

NO.

1

MODEL: SERIAL #:

CMPS2 : 10070560000748, CMPS2E : 10070570000033

SERIAL NUMBERS

CMPS 86305210 6-13

No results