advertisement
®
GARAGE DOOR OPENER
REMOTE COMMAND
CONTROLLER with TILT SENSOR
Installation Instructions
GD00Z-2
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340 www.linearcorp.com
Regulatory Information
Regulatory Information
● Z-Wave® is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.
● Changes or modifi cations not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
● Les changements ou modifi cations non approuvés expressément par la partie responsable de la conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.
● This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
● Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM BATTERY INFORMATION:
THIS PRODUCT CONTAINS A CR COIN CELL LITHIUM BATTERY WHICH CONTAINS
PERCHLORATE MATERIAL - SPECIAL HANDLING MAY APPLY - SEE www.dtsc.ca.gov/hazardouswaste/perchlorate
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY IS SWALLOWED, PROMPTLY SEE A DOCTOR.
DO NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL OF USED BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA.
WARNING
This operator system is equipped with an unattended operation feature. This door could move unexpectedly.
NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type (roll up) doors only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
The Remote Command Controller must be mounted in the garage, in sight of the garage door, where the visual and audible movement warning indicators can be clearly seen and heard.
WARNING
Do not install the Remote Command Controller on garage door operators manufactured prior to 1993
(models without an operational safety beam entrapment detection system).
Table of Contents
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
The Garage Controller System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Tilt Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Mounting the Tilt Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Enrolling with the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Enrolling the Garage Door Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
To add a Garage Door Controller: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Resetting or Excluding the Garage Door Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
To reset a Garage Door Controller: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Deleting the Garage Door Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Controller Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mounting the Controller in the Garage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Controller Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wiring the Controller to the Opener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Opening and Closing the Garage Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Indications and Operation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Tilt Sensor Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
When The Tilt Sensor Battery Gets Low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
If Something is not Working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1
Product Description
Overview
◆ Replication is the process of copying or transferring your Z-Wave network from one controller to another.
◆ This is a Security enabled Z-Wave product and must be used with a Security enabled
Z-Wave controller in order to fully utilize this product. As such, this device will not respond to Basic CC commands.
◆ The GD00Z-2 is a garage door opener remote command transceiver with built-in Z-Wave® technology.
◆ Allows remote operation of a garage door opener using the ADT Pulse touch screen, web portal, or mobile app.
◆ Z-Wave is an Interoperable two-way RF mesh networking technology designed for use with a Z-Wave gateway/controller and other Z-Wave enabled devices.
◆ Acts as a Z-Wave repeater to improve communications within the Z-Wave mesh network.
◆ ASSOCIATION: The GD00Z-2 supports 1 Group with 1 Node. Group 1 must be assigned the
Node ID of the controller to which unsolicited notifi cations from the Controller will be sent.
The ADT Pulse should set this association automatically after inclusion.
Summary of Operation
◆ Controller connects to the garage door opener’s pushbutton wall console terminals.
◆ A wireless tilt sensor mounts on the garage door and reports the door’s position to the
Controller.
◆ GD00Z-2 responds to Z-Wave commands from ADT Pulse to open or close the garage door.
◆ A warning indicator light fl ashes and a beeper sounds for 5 seconds before the door begins to move.
◆ If the door does not completely open or close, a second open or close command can be sent after 30 seconds.
◆ If the door does not completely open or close after the second attempt, the Controller operation is suspended until a local garage door pushbutton is activated.
THE GARAGE DOOR CONTROLLER
SENDS THE DOOR STATUS TO THE
ADT PULSE SYSTEM
THE TILT SENSOR SENDS DOOR
OPEN OR CLOSED STATUS TO THE
GARAGE DOOR CONTROLLER
Figure 1. System Overview
®
THE ADT PULSE SYSTEM
DISPLAYS THE DOOR STATUS
THE ADT PULSE SYSTEM
COMMANDS THE GARAGE DOOR
CONTROLLER TO OPEN
OR CLOSE THE DOOR
2
Package Contents
The Garage Controller System
The GD00Z-2 System consists of three major components:
• The Controller — The Controller wires to the garage door opener’s pushbutton terminals, receives door status from the tilt sensor, and communicates with the ADT Pulse system.
• The Tilt Sensor — The battery powered Tilt Sensor monitors the position of the garage door and sends the status to the Controller.
• The Power Supply — The Power Supply provides low voltage power to the Controller.
POWER
INPUT
JACK
CONNECTION
WIRES
STATUS
INDICATOR
GD00Z-2
GARAGE DOOR
CONTROLLER
WARNING
LIGHT
INCLUDE
BUTTON
MOUNTING SCREWS
AND ANCHORS
FOR GD00Z-2
OPTIONAL
ADJUSTABLE
GD00Z-2 MOUNTING
BRACKET
SCREW AND
MOUNTING HARDWARE
FOR ADJUSTABLE
BRACKET
TILT
SENSOR
SCREWS AND
MOUNTING TAPE
FOR TILT SENSOR
POWER
SUPPLY
SCREW FOR
POWER SUPPLY
BRACKET
Figure 2. Package Contents
POWER
SUPPLY
RETAINING
BRACKET
3
Tilt Sensor Installation
Mounting the Tilt Sensor
The battery powered Tilt Sensor attaches to the top panel of the garage door.
1. Before installation, activate the Tilt Sensor by pulling and removing the battery protection strip.
2. If using screws to mount the Tilt Sensor, open the sensor case with a small screwdriver.
3. Use the double-sided tape or screws supplied to attach the Tilt Sensor to the top panel of the garage door.
✓ NOTE: Drill two 1/16” pilot holes if using the screws to attach the mounting plate.
4. If the plate was removed for screw mounting, snap the Tilt Sensor on to the mounting plate.
✓ NOTE: Be sure the arrow on the side of the Tilt Sensor points UP.
1
TO ACTIVATE THE TILT SENSOR,
REMOVE THE BATTERY PROTECTION PULL STRIP
2
TO OPEN THE CASE, FOR SCREW
MOUNTING, TWIST A SMALL
SCREWDRIVER IN THE CASE SLOT
3
ATTACH MOUNTING PLATE
TO TOP PANEL OF THE DOOR
SLOT
ARROW
ON PLATE
POINTS UP
"UP"
ARROW
POST ON
BOTTOM
USE DOUBLE SIDED TAPE OR
THE TWO MOUNTING SCREWS SUPPLIED
(DRILL 1/16" PILOT HOLES IF REQUIRED)
4
SNAP THE TILT SENSOR
ONTO THE MOUNTING PLATE
ARROW
ON SENSOR
POINTS UP
Figure 3. Tilt Sensor Installation
4
Enrolling with the System
Enrolling the Garage Door Controller
Before the system can be used, the ADT Pulse system needs to enroll the Garage Door
Controller. Bring the Controller near your ADT Pulse Gateway and apply power to the
Garage Door Controller.
✓ NOTE: Before enrolling device to any Z-Wave network, or after removing it from any Z-Wave
network, it is recommended that the Controller be factory reset. Reset the Controller by pressing the Include button 5 times.(Location of Include button is shown in Figure 2 on
Page 3). A quick beep followed by a longer beep will indicate proper reset of the GD00Z-2.
To add a Garage Door Controller:
1. Open your Web browser and in the address bar enter:
https://portal.adtpulse.com
2. Enter your Username and Password, then click the Sign In button.
3. Click the System tab, then click the Manage Devices button. The Manage Devices
Assistant appears.
5
Enrolling with the System (Cont.)
4. In the Manage Devices Assistant window, click Lights, Thermostats & More.
5. From the drop-down list, select the Garage Door Remote Controller, and then click
Continue.
6. At the Trigger Device screen, press and hold the Garage Door Controller’s include button for 1 second (See page 3, Figure 2 for the location of the include button).
7. Wait while the system fi nds the GD00Z-2 Device. When the device is successfully recognized, the Found Device screen appears.
✓ NOTE: Adding the Garage Door Controller can take one or two minutes.
6
Enrolling with the System (Cont.)
8. Enter a name for the device, and then click Continue.
A message informs you that the device was successfully added.
9. Click Finish.
7
Enrolling with the System (Cont.)
Resetting or Excluding the Garage Door Controller
If you have trouble adding the Garage Door Controller you can reset the device. Resetting the device removes it from a site (Not the same as factory resetting the device). You can then try to add the device again.
To reset a Garage Door Controller:
1. In the web portal, click the System tab.
2. Click Manage Devices.
◆ The Manage Devices Assistant wizard appears.
3. Click Lights, Thermostats & more.
◆ The Z-Wave Assistant wizard appears.
4. Click Reset Device.
5. Press and release the Garage Door Controller’s include button once.
◆ The Z-Wave device resets.
6. Click Cancel.
Deleting the Garage Door Controller
To delete the Garage Door Controller:
1. Click the System tab, if it is not already selected.
2. Click the name of the device you want to delete. The device page displays information about the selected device.
3. Click Delete. A pop-up window prompts you to confi rm the deletion.
4. Click Yes to complete the deletion.
✓ NOTE: If you attempt to delete a device that is referenced in an automation, alert, or
schedule, or replace the device in all automations, alerts, and schedules in which it is referenced before you can delete the device. Click OK to exit without deleting the device.
8
Controller Mounting
Mounting the Controller in the Garage
The Garage Door Controller mounts in the garage near the garage door opener. It will need to be near a power outlet and where its warning lamp can be seen, regardless of the door position. Un-plug the garage door opener before continuing.
The Garage Door Controller can be screw mounted directly, or by using the supplied adjustable mounting bracket.
1. Use the four anchors and screws to directly mount the Controller (use a 3/16” drill for the screw anchors, if the anchors are used).
- OR -
1. Snap the adjustable mounting bracket onto the Controller and secure it with the short screw.
2. Use the bolts and nuts supplied to attach the mounting bracket to available hardware.
TILT SENSOR
MOUNTED ON
THE TOP PANEL
OF THE DOOR
THE GD00Z-2 TYPICALLY
MOUNTS ON THE CEILING
NEAR THE OPENER AND
THE POWER OUTLET
! WARNING !
REMOVE POWER FROM THE
GARAGE DOOR OPENER
BEFORE CONTINUING
THE GD00Z-2 WARNING
LAMP MUST BE VISIBLE IN
ALL DOOR POSITIONS
Figure 4. Controller Components
TYPICAL MOUNTING METHOD
1
USE THE FOUR SCREWS
AND ANCHORS TO MOUNT
THE GD00Z-2 ABOVE
THE OPENER
3/16" HOLES
FOR ANCHORS
ALTERNATE MOUNTING METHOD
THE GD00Z-2 CAN ALSO BE ATTACHED TO THE OPENER'S
HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET
SECURE
BRACKET
WITH SCREW
1A
THE OPTIONAL ADJUSTABLE
MOUNTING BRACKET FITS
3 WAYS ON THE CONTROLLER
INDENT
INDENT
THE BRACKET SNAPS ONTO
INDENTS ON EITHER SIDE OR
ON THE END OF THE CONTROLLER
INDENT
2A
USE THE BOLTS AND NUTS
SUPPLIED TO ATTACH THE
BRACKET TO A SECURE
STRUCTURE
BE SURE THE CONTROLLER
IS CLEAR OF ALL MOVING
PARTS OF THE GARAGE DOOR
AND THE WARNING LAMP IS
NOT OBSTRUCTED
Figure 5. Controller Mounting
9
Controller Connections
Wiring the Controller to the Opener
The Garage Door Controller wires to the garage door opener with a two wire connection.
1. Connect the GD00Z-2 connection wires to the two pushbutton terminals on the garage door opener. The terminals on various models may have different names. Either wire can connect to either terminal.
✓ IMPORTANT! Be sure the wires clear all moving parts of the door and opener.
Connecting the Power Supply
2. Plug the Power Supply’s cord into the jack on the Garage Door Controller.
3. Plug the Power Supply into a 115 VAC outlet. Be sure the outlet is powered at all times and not controlled by a switch.
✓ IMPORTANT! Do not disconnect any wires currently connected to the Garage Door
Opener.
2
PLUG THE POWER CORD
INTO THE POWER INPUT
JACK ON THE GD00Z-2
1
CONNECT THE GD00Z-2 CONNECTION
WIRES TO THE PUSHBUTTON WALL
CONSOLE TERMINALS ON THE GARAGE
DOOR OPENER. THE TERMINALS MAY BE
NAMED "PWC", "WC", "PB", "PUSHBUTTON",
OR "RED AND WHITE". TERMINAL NAMES
AND LOCATIONS VARY BY MODEL.
EITHER WIRE
CAN CONNECT
TO EITHER
TERMINAL
GARAGE
DOOR
OPENER
3
PLUG THE POWER SUPPLY
INTO 115 VAC OUTLET
AND SECURE IT WITH
THE RETAINING BRACKET
DO NOT DISCONNECT
ANY WIRES CURRENTLY
CONNECTED TO THE
GARAGE DOOR OPENER !!!
BE SURE WIRES ARE
CLEAR OF ALL MOVING
PARTS OF THE GARAGE
DOOR AND OPENER
Figure 6. Controller Mounting
10
System Operation
Opening and Closing the Garage Door
After the installation is complete, the garage door opener can be activated by the ADT
Pulse system and the door’s status can be viewed through the system.
1. Restore power to the garage door opener.
2. Cycle the door open and closed using the wall pushbutton to synchronize the system.
3. Command the ADT Pulse system to activate the garage door.
4. Verify that the Garage Door Controller fl ashes for fi ve seconds before the door moves.
5. The door should open or close.
6. Verify that the ADT Pulse system indicates the open or closed status of the garage door.
1
RESTORE POWER TO YOUR
GARAGE DOOR OPENER
2
TO SYNCHRONIZE THE SYSTEM,
USE THE GARAGE DOOR OPENER'S
PUSHBUTTON TO MANUALLY OPEN
AND CLOSE THE DOOR
3
USE THE ADT PULSE TOUCHSCREEN
OR MOBILE APP TO CONTROL
YOUR GARAGE DOOR, VIEW
STATUS, AND ADD YOUR
GARAGE DOOR CONTROL TO
AUTOMATIONS AND MODES
(FOR EXAMPLE, YOU CAN
SCHEDULE YOUR GARAGE DOOR
TO CLOSE NIGHTLY AT SUNSET)
4
THE GD00Z-2 WILL BEEP AND
FLASH FOR FIVE SECONDS BEFORE
THE DOOR MOVES
5
THE GD00Z-2 WILL ACTIVATE
THE DOOR OPENER AND OPEN
OR CLOSE THE DOOR
6
THE TOUCHSCREEN OR MOBILE
APP WILL SHOW THE NEW STATUS
OF THE DOOR AFTER THE DOOR
COMPLETES ITS CYCLE
Figure 7. Controller Mounting
BEEP
BEEP
BEEP
FLASH
FLASH
FLASH
STAY CLEAR
OF THE DOOR !!!
STAY CLEAR
OF THE DOOR !!!
11
Operation Notes
Indications and Operation Notes
◆ The warning light will fl ash and the warning beeper will sound for fi ve seconds before the door opener is activated. STAY CLEAR OF THE DOOR, AND DOOR OPENER. THEY ARE
ABOUT TO MOVE!
◆ If the door does not completely open or close after remote activation, the Controller will allow user to try to operate the door one more time. If the second attempt fails, the
Controller will go into lock-out mode. See next paragraph.
◆ If the GD00Z-2 is in lock-out mode and will not accept remote commands, activate the door from the pushbutton wall console.
◆ Once the Controller has initiated the movement of the garage door, another command cannot be sent for 30 seconds. This eliminates the chance of “bouncing” the garage door and possibly damaging the garage door opener.
Tilt Sensor Battery Replacement
When The Tilt Sensor Battery Gets Low
The system will notify you when the Tilt Sensor battery gets low and needs replacing.
1. Use a small screwdriver to open the Tilt Sensor case.
2. Remove the low battery and insert a fresh Type CR2032 coin cell battery. BE SURE THE
PLUS SIDE IS UP.
✓ IMPORTANT! Disposal of used batteries must be made in accordance with the waste
recovery and recycling regulations in your area.
3. Return the Tilt Sensor to the garage door top panel and snap it onto the mounting plate.
BE SURE THE ARROW ON THE SIDE OF THE TILT SENSOR IS POINTING UP.
12
1 TO OPEN THE CASE, TWIST
A SMALL SCREWDRIVE IN
CASE SLOT
SLOT
CR2032
2
INSERT THE FRESH
BATTERY INTO THE
TRANSMITTER
THE SYSTEM WILL NOTIFY YOU
WHEN THE BATTERY IS LOW,
REPLACE THE BATTERY WITH
A TYPE CR2032 COIN CELL
SNAP SENSOR ONTO
THE MOUNTING PLATE
"UP"
ARROWS
3
SNAP THE TILT SENSOR ONTO
THE MOUNTING PLATE BEING
SURE THAT THE ARROW ON THE
SIDE IS POINTING UP
Figure 8. Replacing the Tilt Sensor Battery
Troubleshooting
If Something is not Working
Refer to the following table for information regarding possible problems and solutions if the
Garage Door Controller is not operating as expected.
PROBLEM
The Controller does not fl ash or beep when activated.
The Controller fl ashes and beeps when activated but the door does not move.
Garage door opens or closes, but the status does not change on the touch screen or mobile app.
POSSIBLE CAUSE
No power to the
Controller
CORRECTIVE ACTION
1. Make sure the power supply is plugged in securely to a live outlet.
2. Make sure the power cord is plugged in securely to the
Controller
Obstruction blocking the door or incorrect wiring.
The Tilt Sensor signal is not being received by the Controller
1. Make sure that there are no obstacles preventing the door from moving.
2. Make sure that the GD00Z-2 connection wires are connected to the proper terminals on the garage door opener. Trace the wires from the garage door opener’s pushbutton wall console to the door opener. This is where the
GD00Z-2 connection wires should be connected to.
1. Make sure the Tilt Sensor is mounted correctly on the garage door, with the arrow pointing up.
2. Make sure the battery pull tab has been removed from the Tilt
Sensor.
3. Replace the battery in the Tilt
Sensor.
13
®
Copyright © 2014 Linear LLC 235971 X22
advertisement
Related manuals
advertisement