Telemecanique Altivar 71 Controller Inside programmable card User's manual
Reklama
Reklama
User's manual
Retain for future use
Altivar 71
"Controller Inside" Card
VW3 A3 501
efesotomasyon.com
efesotomasyon.com
Sommaire
Before you begin_____________________________________________________________________________________________ 4
Documentation structure_______________________________________________________________________________________ 5
Introduction _________________________________________________________________________________________________ 6
Presentation _____________________________________________________________________________________________ 6
Description ______________________________________________________________________________________________ 6
Dialog __________________________________________________________________________________________________ 7
Master CANopen communication _____________________________________________________________________________ 7
Communication with a PLC _________________________________________________________________________________ 7
Clock___________________________________________________________________________________________________ 8
Programming ____________________________________________________________________________________________ 8
Hardware setup _____________________________________________________________________________________________ 9
Receipt _________________________________________________________________________________________________ 9
Installing the card in the drive ________________________________________________________________________________ 9
Description of terminals ___________________________________________________________________________________ 10
Characteristics __________________________________________________________________________________________ 11
Schemes_______________________________________________________________________________________________ 12
Connection to a CANopen bus ______________________________________________________________________________ 13
Example of connection to a CANopen bus _____________________________________________________________________ 14
Connecting the "Controller Inside" card to a PC_________________________________________________________________ 15
Data backup battery ______________________________________________________________________________________ 16
Configuration ______________________________________________________________________________________________ 17
Configuring the switches___________________________________________________________________________________ 17
Diagnostics ________________________________________________________________________________________________ 18
LEDs __________________________________________________________________________________________________ 18
I/O monitoring ___________________________________________________________________________________________ 19
Card fault ______________________________________________________________________________________________ 20
Operation using the graphic display terminal ______________________________________________________________________ 21
Factory-loaded program ___________________________________________________________________________________ 21
Example of a special program ______________________________________________________________________________ 23
Operation using the integrated display terminal ____________________________________________________________________ 24
Factory-loaded program ___________________________________________________________________________________ 24
Special program _________________________________________________________________________________________ 24
While every precaution has been taken in the preparation of this document,
Schneider Electric SA assumes no liability for any omissions or errors it may contain, nor for any damages resulting from the application or use of the information herein.
The products and options described in this document may be changed or modified at any time, either from a technical point of view or in the way they are operated.
Their description can in no way be considered contractual.
efesotomasyon.com
3
4
Before you begin
Read and understand these instructions before performing any procedure on this drive.
DANGER
HAZARDOUS VOLTAGE
• Read and understand the Installation manual before installing or operating the Altivar 71 drive. Installation, adjustment, repair, and maintenance must be performed by qualified personnel.
• The user is responsible for compliance with all international and national electrical standards in force concerning protective grounding of all equipment.
• Many parts of this variable speed drive, including the printed circuit boards, operate at the line voltage.
DO NOT TOUCH.
Use only electrically insulated tools.
• DO NOT touch unshielded components or terminal strip screw connections with voltage present.
• DO NOT short across terminals PA and PC or across the DC bus capacitors.
• Install and close all the covers before applying power or starting and stopping the drive.
• Before servicing the variable speed drive
- Disconnect all power
- Place a “DO NOT TURN ON” label on the variable speed drive disconnect
- Lock the disconnect in the open position
• Disconnect all power including external control power that may be present before servicing the drive.
WAIT 15 MINUTES to allow the DC bus capacitors to discharge. Then follow the DC bus voltage measurement procedure given in the installation manual to verify that the DC voltage is less than 45 VDC. The drive LEDs are not accurate indicators of the absence of DC bus voltage.
Electric shock will result in death or serious injury.
CAUTION
DAMAGED EQUIPMENT
Do not install or operate any drive that appears damaged.
Failure to follow this instruction can result in equipment damage.
efesotomasyon.com
Documentation structure
Installation manual
This manual describes:
• Assembly
• How to connect the drive
Programming manual
This manual describes:
• The functions
• The parameters
• How to use the drive display terminal (integrated display terminal and graphic display terminal)
Communication parameters manual
This manual describes:
• The drive parameters with specific information (addresses, formats, etc) for use via a bus or communication network
• The operating modes specific to communication (state chart)
• The interaction between communication and local control
Modbus, CANopen, Ethernet, Profibus, INTERBUS, Uni-Telway, DeviceNet, Modbus Plus and FIPIO manuals
These manuals describe:
• Connection to the bus or network
• Configuration of the communication-specific parameters via the integrated display terminal or the graphic display terminal
• Diagnostics
• Software setup
• The communication services specific to the protocol
Altivar 58/58F compatibility manual
This manual describes the differences between the Altivar 71 and the Altivar 58/58F.
It explains how to replace an Altivar 58 or 58F, including how to replace drives communicating on a bus or network.
efesotomasyon.com
5
6
Introduction
Presentation
The “Controller Inside” programmable card is used to adapt the variable speed drive to specific applications by integrating control system functions.
Various predefined configurable applications are sold by Telemecanique and its partners.
The PS 1131 software workshop for PC is used for programming and debugging new applications, quickly and in an open-ended manner.
It is not possible to transfer the program from the card to the PC, which enables us to protect our know-how.
Only one “Controller Inside” programmable card can be installed in the Altivar 71 drive. It can be combined with another option card
(I/O extension or communication). Consult the tables summarizing the possible combinations: drives, options and accessories, see catalogue.
The “Controller Inside” programmable card has:
• 10 logic inputs, 2 of which can be used for 2 counters or 4 of which can be used for 2 incremental encoders
• 2 analog inputs
• 6 logic outputs
• 2 analog outputs
• A master port for the CANopen bus
• A PC port for programming with the PS 1131 software workshop
• If the power consumption table does not exceed 200 mA, this card can be powered by the drive. Otherwise, an external 24 V c power supply must be used.
The “Controller Inside” programmable card can also use:
• The drive I/O
• The I/O extension card I/O
• The encoder interface card points counter
• The drive parameters (speed, current, torque, etc)
Description
5 6
1 2 3
4
1 RJ45 connector for connecting the PS 1131 software workshop via an RS 485 serial link.
Connection to the PC is via a cable and an RS 232/RS 485 converter included in the
PowerSuite for PC connection kit, VW3 A8 106.
2 9-way male SUB-D connector for connection to the CANopen bus.
3 Connector with removable screw terminals, 6 contacts at intervals of 3.81 for the
24 V c power supply and 4 logic inputs.
4 3 connectors with removable screw terminals, 6 contacts at intervals of 3.81 for 6 logic inputs, 6 logic outputs, 2 analog inputs, 2 analog outputs and 2 commons.
5 5 LEDs, comprising:
• 1 to indicate the presence of the 24 V c power supply
• 1 to indicate a program execution fault
• 2 to indicate the CANopen bus communication status
• 1 controlled by the application program
6 Block of 4 configuration switches efesotomasyon.com
Introduction
Dialog
ATV 71
Modbus bus
XBT Magelis
Human-machine dialog with the application programmed in the “Controller Inside” programmable card is possible using:
• The Altivar 71 graphic display terminal
• A Magelis industrial HMI terminal connected to the drive Modbus port
• A Magelis industrial HMI terminal connected to the Ethernet TCP/IP network (if the drive is equipped with an Ethernet TCP/IP communication card)
One graphic terminal menu is dedicated to the “Controller Inside” programmable card. This menu can be customized by the card program according to the application.
Any industrial HMI terminal which supports the Modbus protocol can be used to display and modify the “Controller Inside” programmable card parameters. The card Modbus server provides access to 2048 Kwords (% MW, etc).
Sensors
Independent machine with multiwire system
Master CANopen communication
ATV 71 XBT Magelis
The master CANopen port on the “Controller Inside” programmable card can be used to extend the I/O capacity (using CANopen I/O modules) and to control other
CANopen slave devices.
Modbus bus
CANopen bus
ATV 31
ATV 31 Advantys STB distributed I/O
Independent machine with CANopen bus
FTB 1CN
Communication with a PLC
Premium
XBT Magelis
ATV 71
Ethernet TCP/IP network
ATV 71
The Altivar 71 drive equipped with a “Controller Inside” programmable card fits easily into complex architectures.
Regardless of which bus or network is being used (Ethernet TCP/IP, Modbus/
Uni-Telway, FIPIO, Modbus Plus, Profibus DP, InterBus, etc), the PLC can communicate with the “Controller Inside” programmable card and the drive. The periodic variables can still be configured as required.
CANopen bus
Sensors ATV 31
Modular machine with Ethernet TCP/IP network
FTB 1CN efesotomasyon.com
7
8
Introduction
Clock
A clock backed up by a lithium battery makes it possible to have a log of events that have occurred. When the “Controller Inside” programmable card is installed in the drive, the drive faults are automatically time and date-stamped without special programming.
Programming
In factory settings mode, the "Controller Inside" card only contains the clock function.
For other applications, the program must be loaded:
• By loading an existing program (procedure described in the PS 1131documentation)
• Or by loading a custom-built program, with the aid of the PS 1131 software workshop, using the function libraries dedicated to programming the "Controller Inside" card.
In order to program the "Controller Inside" card, it is necessary to undergo training.
The PS1131 CD-Rom contains:
• This manual, already available on the CD-Rom supplied with each Altivar 71
• The PS 1131 software workshop
• The online help
• The standard function library
• Program examples
• The Altivar 71 parameters manual
The standard function library contains:
• Logic functions (AND, OR, etc)
• Mathematical functions (Cos, Sin, Exp, etc)
• Functions dedicated to drives which simplify data exchanges between the drive and the "Controller Inside" programmable card (example: sending the speed reference)
• Functions for managing the CANopen bus
• Graphic terminal display functions
This manual does not describe programming using PS 1131.
Note: PS 1131 is also called CoDeSys.
CoDeSys V2.2 can be used on the Controller Inside for Altivar 58 (VW3A581131), but must not be used for programming the Controller
Inside for Altivar 71 (VW3 A3 501).
efesotomasyon.com
Hardware setup
Receipt
• Check that the card catalog number marked on the label is the same as that on the delivery note corresponding to the purchase order.
• Remove the option card from its packaging and check that it has not been damaged in transit.
• Check that the product is complete: the packaging should contain the "Controller Inside" option card and its 4 removable terminals.
Installing the card in the drive
See the Altivar 71 Installation Manual.
Note: If a Controller Inside card and an I/O extension card are installed simultaneously:
• The I/O extension card must be installed on the drive first
• Then the Controller Inside card must be installed on the I/O extension card efesotomasyon.com
9
Hardware setup
Description of terminals
LI60
LI59
LI58
LI57
LI56
LI55
AO52
COM
A051
AI52
COM
AI51
LO56
LO55
LO54
LO53
LO52
LO51
Terminal
24V
COM
Function
Power supply for the "Controller Inside" card, logic outputs and analog outputs.
If allowed by the power consumption table (for example if outputs are not being used), the "Controller Inside" card can be powered by the 24 V c
power supply in the drive.
If you are using an external power supply:
• The "Controller Inside" card should preferably be turned on before the drive. However, the "Controller Inside" card must without fail be turned on no more than 2s after the drive is turned on.
Failure to follow this instruction locks the drive in card fault mode (ILF). This fault cannot be reset, and the only way to acknowledge it is to turn off the drive.
• Catalog number for a Telemecanique power supply (24 V c
, 2A): ABL7 RE 24 02.
Common ground and electrical 0V of the "Controller Inside" card power supply, logic inputs, (LI pp
), outputs (LO pp
), analog inputs (AI pp
) and analog outputs (AO pp
).
LI51 to LI60
This ground and electrical 0V are common with the drive ground and electrical 0V. There is therefore no point in connecting this terminal to the 0V terminal on the drive control terminals.
24 V c
logic inputs
Inputs LI51, LI52, LI59 and LI60 can be configured for the use of 2 counter inputs or 2 incremental encoder inputs:
Counter 1 input: LI51
Incremental encoder 1 inputs: channel A = LI51, channel B = LI52
Counter 2 input: LI59
Incremental encoder 2 inputs: channel A = LI59, channel B = LI60
LO51 to LO56 24 V c
logic outputs
AI51 and AI52 0 ... 20mA analog inputs
AO51 and AO52 0 ... 20mA analog outputs
10 efesotomasyon.com
Hardware setup
Characteristics
Electrical characteristics
Power
Current consumption
Analog inputs
Analog outputs
Logic inputs
Logic outputs
I/O connection
Lithium battery
Voltage
Maximum
No-load
Using logic output
AI51, AI52
AO51, AO52
LI51…LI60
LO51…LO56
Type of contact
Maximum wire
Tightening torque
Life
V
A mA mA mm
2
Nm
24 c (min. 19, max. 30)
2
80
200 maximum (1)
2 current analog inputs 0
…20 mA, impedance 250 Ω
Resolution: 10 bits
Accuracy: ± 1% for a temperature variation of 60°C
Linearity: ± 0.2% of the maximum value
Common point for all the card I/O (2)
2 current analog outputs 0
…20 mA, impedance 500 Ω
Resolution: 10 bits
Accuracy: ± 1% for a temperature variation of 60°C
Linearity: ± 0.2% of the maximum value
Common point for all the card I/O (2)
10 logic inputs, 2 of which can be used for 2 counters or 4 of which can be used for 2 incremental encoders
Impedance 4.4 k
Ω
Maximum voltage: 30 V c
Switching thresholds:
State 0 if y 5 V or logic input not wired
State 1 if u 11 V
Common point for all the card I/O (2)
Six 24 V c logic outputs, positive logic open collector type (source), compatible with level 1 PLC, standard IEC 65A-68
Maximum switching voltage: 30 V
Maximum current: 200 mA
Common point for all the card I/O (2)
Screw, at intervals of 3.81 mm
2
1.5 (AWG 16)
0.25
8 years approx.
Characteristics of the application program
Compiled program
(saved in “flash” memory)
Data
Maximum size
Kb
320
Maximum size Kword 64
Saved size (NVRAM) Kword 4
Size accessible by
Modbus
Kword 2
Characteristics of the CANopen communication port
Structure
Services
Diagnostics
Connector One 9-way male SUB-D connector
Network management Master
Transmission speed
Address (Node ID)
Configurable via the program:
50 kbps, 125 kbps, 250 kbps, 500 kbps or 1 Mbps
32 slaves maximum
DS 301 V4.02
CANopen application layer
Channel config.
PDO
SDO
Error check
Other services
Configuration
Using LEDs
DSP 405
9 receive and transmit PDOs in total for each slave
2 client SDOs per slave (1 read and 1 write). Block transfer
Node Guarding, producer and consumer Heartbeat
Emergency, Boot-up, Sync
The CANopen network configurator is integrated in the PS1131 software workshop.
2 LEDs: “RUN” and “ ERROR”, conforming to CIA DR303 version 1.0
(1) If the power consumption table does not exceed 200 mA, this card can be powered by the drive. Otherwise, an external 24 V
c
power supply must be used.
(2) This common point is also the drive 0 V (COM).
efesotomasyon.com
11
Hardware setup
Schemes
Card powered by the drive
Only if the power consumption is less than 200 mA; otherwise use an external power supply.
ATV 71Hppppp VW3 A3 501
SW1
Source
Sink
Ext. Int.
Card powered by external power supply
0-20 mA 0-20 mA
VW3 A3 501
+
24 V
0 V
24 V c supply
0-20 mA 0-20 mA 0-20 mA 0-20 mA
12 efesotomasyon.com
Hardware setup
Connection to a CANopen bus
Pinout for the CANopen 9-way SUB-D connector
1
9
5
6
Terminal
1
2
3
4
5
6
7
8
9
Description
not connected
CAN_L
CAN_GND not connected not connected
CAN_GND
CAN_H not connected not connected
Use a straight connector (catalog number TSX CAN KCDF 180T) to connect the "Controller Inside" card to the CANopen bus.
This connector integrates a line terminator that must be activated if the "Controller Inside" card is at one end of the CANopen bus.
It is not possible to use an angled connector because of the terminals located to the right of the CANopen connector.
The 9-way SUB-D connector on the "Controller Inside" card is linked to the card ground and the drive ground. The shielding must be connected to the connector ground.
The CANopen signals on the "Controller Inside" card are isolated.
Speed and length of the CANopen bus
It is essential to make sure that all devices connected to the CANopen bus operate at the same transmission speed.
The CANopen transmission speed of the "Controller Inside" card is configured from the PS 1131 software workshop.
The maximum length of the CANopen bus depends on the transmission speed on this bus.
The table below indicates the maximum lengths permitted according to the transmission speed:
Transmission speed
Max. length of bus
50 kbps
1000m
125 kbps
500m
250 kbps
200m
500 kbps
100m
1 Mbps
5m efesotomasyon.com
13
Hardware setup
Example of connection to a CANopen bus
Description
Altivar 71 drive equipped with a "Controller Inside" card
CANopen connector
9-way female SUB-D connector with line terminator (can be deactivated)
2 CANopen cables can be connected
180° cable outlet
CAN-H, CAN-L, CAN-GND connection
LSZH CANopen cable
CE certified CANopen cable. Low smoke emission, non halogen and flame retardant
(IEC 60332-1).
UL/IEC332-2 CANopen cable
UL certified CANopen cable. Flame retardant (IEC 60332-2).
3
3
Reference number
Length m
1
-
2
-
Catalog number
ATV71
pppp
VW3 A3 501
TSX CAN KCDF 180T
3
4
50
100
300
50
100
300
50
-
100
300
TSX CAN CA 50
TSX CAN CA 100
TSX CAN CA 300
TSX CAN CB 50
TSX CAN CB 100
TSX CAN CB 300
TSX CAN CD 50
TSX CAN CD 100
TSX CAN CD 300
VW3 CAN TAP 2
LSZH HD flexible CANopen cable
CANopen cable for intensive use and moving applications. Flame retardant
(IEC 60332-1). Non halogen. Oil resistant.
Junction box for CANopen bus
2 RJ45 connectors for connecting 2 drop cables
VW3 CAN CA RR pp
1 RJ45 connector for connecting the PowerSuite software workshop
Two 5-pin screw terminals for connecting 2 CANopen cables (CAN_H, CAN_L,
CAN_GND, CAN_V+, CAN_SHLD)
Line terminator (can be deactivated)
Drop cable for CANopen bus
Equipped with 2 RJ45 connectors
Altivar 31 drive
CANopen Advantys OTB I/O modules
Power supply 24 V c
, 12 inputs 24 V c
, 2 outputs 24 V c
0.3A
6 relay outputs 30 V c
/240 V a
2 A, removable screw terminals
CANopen Advantys FTB I/O module
M12 connector for CANopen cable
5 female contacts, A coding
CANopen extension cable for Advantys FTB module
Equipped with 2 angled connectors: M12, 5-way, A coding
CANopen line terminator for Advantys FTB module
Equipped with an M12 connector
5
6
7
8
9
10
11
-
-
-
-
-
0.3
1
VW3 CAN CA RR03
VW3 CAN CA RR10
ATV31
ppp
OTB1 C0 DM9LP
FTB 1CN
ppp p
0
FTX CN12F5
FTX CN32
pp
FTX CNTL12
14 efesotomasyon.com
Hardware setup
Connecting the "Controller Inside" card to a PC
The "Controller Inside" card RJ45 connector complies with the RS485 standard.
The connection kit for PC serial port (catalog number VW3 A8 106) can be used to connect a PC to the "Controller Inside" card.
This kit contains a cable equipped with 2 RJ45 connectors, as well as an RS485/RS232 converter.
As the RS485/RS232 converter is powered by the "Controller Inside" card, no external power supply is required.
Characteristics of the programming port
The RJ45 connector is shielded and connected to the ground on the "Controller Inside" card, which is itself connected to the drive ground.
View from
8.......................1
Terminal
1
2
3
6
7
4
5
8
Description
not connected not connected not connected
B signal (RS485) = V1 signal (Modbus)
A signal (RS485) = V0 signal (Modbus) not connected
Modbus VP signal
12 V DC power supply supplied by the "Controller Inside" card (only for the power supply of a
RS485/RS232 converter)
Modbus common signal
0V efesotomasyon.com
15
Hardware setup
Data backup battery
The "Controller Inside" card has a non-volatile RAM (NVRAM) which is needed to store variables. A lithium battery is mounted on this nonvolatile RAM to avoid this data being lost when the card is turned off.
When installing the "Controller Inside" card in the drive, make sure that this battery is present. It takes the form of a rectangular block clipped onto the non-volatile RAM
(see schematic opposite).
The battery life is approximately 8 years when turned off.
Lithium battery
The battery has a realtime clock for timestamping faults.
The date and time on this clock are checked and set from a special sub-menu in the
[1.14 - PROG. CARD MENU]
customizable menu in the graphic display terminal.
The date and time need to be set on receipt of the "Controller Inside" card, or after replacing its lithium battery.
The lithium battery must only be replaced when the drive and the "Controller Inside" card are turned off.
During this operation, the data saved in the NVRAM (4 Kwords) are lost.
16 efesotomasyon.com
Configuration
Configuring the switches
The "Controller Inside" card has a block of 4 switches as illustrated below.
These switches can only be set when the drive and the "Controller Inside" card are turned off, since it is necessary to remove the drive control front panel in order to access it.
By default, all the switches are in the Off position.
Write protection switch
The right-hand switch (switch 4) is used to protect the PS 1131 program in the Flash memory.
Switches Description
A new program cannot be transferred.
A new program can be transferred.
Programmable switches
The three left-hand switches (switches 1 to 3) can be used by the "Controller Inside" card program, depending on the application.
Switches Value Switches Value Switches Value Switches Value
0 1 2 3
4 5 6 7
efesotomasyon.com
17
Diagnostics
LEDs
The "Controller Inside" card is equipped with five LEDs which can be seen through the window in the Altivar 71 cover.
1.1 CANopen RUN
1.2 CANopen ERROR
1.3 Power
1.4 Application
1.5 Watchdog
LED
1.1 CANopen RUN
Color State
green
1.2 CANopen ERROR red
1.3 Power
1.4 Application
1.5 Watchdog
green yellow red off flashing on off
1 flash per second
2 flashes per second on off on on
Meaning
CANopen master in STOPPED state
CANopen master in PRE-OPERATIONAL state
CANopen master in OPERATIONAL state
No CANopen error
The CANopen master error counter has reached or exceeded its warning level
(too many errors)
Node Guarding error (vis-à-vis a CANopen slave) or Heartbeat error (CANopen master acting as consumer)
The CANopen master is in the "OFF" state.
"Controller Inside" card not supplied with power
"Controller Inside" card supplied with power (24 V c
present)
The meaning of this LED is determined by the "Controller Inside" card program.
The "Controller Inside" card program has generated an error and has been stopped (watchdog tripped).
18 efesotomasyon.com
Diagnostics
I/O monitoring
The values of all the "Controller Inside" card logic and analog I/O can be displayed on the graphic display terminal:
[1.2 - MONITORING]
menu,
[ PROG. CARD I/O MAP]
sub-menu.
RUN Term +50.00Hz
80A
PROG. CARD I/O MAP
PROG CARD LI MAP
PROG CARD AI MAP
PROG CARD LO MAP
PROG. CARD AO MAP
Code Quick
Move from one screen to another
(from PROG CARD LI MAP to PROG. CARD AO MAP) by turning the navigation button state 0 state 1
RUN Term +50.00Hz
80A
PROG CARD LI MAP
LI51 LI52 LI53 LI54 LI55 LI56 LI57 LI58
1
0
LI59 LI60
1
0
<< >> Quick
RUN Term +50.00Hz
80A
PROG CARD AI MAP
AI51 : 0.000 mA
AI52 : 9.87 V
ENT
RUN Term +50.00Hz
80A
AI51
0 mA
Min = 0.001 Max = 20,000
<< >> Quick Code << >> Quick state 0 state 1
RUN Term +50.00Hz
80A
PROG CARD LO MAP
LO51 LO52 LO53 LO54 LO55 LO56
1
0
<< >> Quick
RUN Term +50.00Hz
80A
PROG. CARD AO MAP
AO51 : 0.000 mA
AO52 : 9.87 V
ENT
RUN Term +50.00Hz
80A
AO51
0 mA
Min = 0.001 Max = 20,000
<< >> Quick Code << >> Quick
Note: The addresses of the parameters mentioned above are given in the "Communication parameters manual".
efesotomasyon.com
19
Diagnostics
Value
0
1
2
3
7
8
9
10
11
101
4
5
6
102
103
Card fault
The
[internal com. link] (ILF)
fault appears when serious problems arise:
- Hardware fault in the Controller Inside card
- Dialog fault between the Controller Inside card and the drive
The drive behavior cannot be configured when an
[internal com. link] (ILF)
fault occurs, and the drive trips with freewheel stopping. This fault cannot be reset.
Two diagnostic parameters can be used to obtain more detailed information on the origin of the
[internal com. link] (ILF)
fault:
-
[Internal link fault 1] (ILF1)
if the fault has occurred on option card no. 1 (installed directly on the drive).
-
[Internal link fault 2] (ILF2)
if the fault has occurred on option card no. 2 (installed directly on the drive).
The Controller Inside card can be in position 1 or in position 2.
Parameters
[Internal link fault 1] (ILF1)
and
[Internal link fault 2] (ILF2)
can only be accessed on the graphic display terminal, in the
[1.10
DIAGNOSTICS] (DGT-)
,
[MORE FAULT INFO] (AFI-)
menu.
Description of the values of the [Internal link fault 1] (ILF1) and [Internal link fault 2] (ILF2) parameters
No fault
Loss of internal communication with the drive
Hardware fault detected
Error in the EEPROM checksum
Faulty EEPROM
Faulty Flash memory
Faulty RAM memory
Faulty NVRAM memory
Faulty analog input
Faulty analog output
Faulty logic input
Faulty logic output
Unknown card
Exchange problem on the drive internal bus
Time out on the drive internal bus (500 ms)
20 efesotomasyon.com
Operation using the graphic display terminal
Factory-loaded program
Controller Inside menu
RDY
1 DRIVE MENU
2 ACCESS LEVEL
3 OPEN / SAVE AS
4 PASSWORD
5 LANGUAGE
Code
Term +0.00Hz
MAIN MENU
0A
Quick
ENT
RDY Term +0.00Hz
1 DRIVE MENU
1.1 SIMPLY START
1.2 MONITORING
1.3 SETTINGS
1.4 MOTOR CONTROL
1.5 INPUTS/OUTPUTS CFG
Code << >>
1.6 COMMAND
1.7 APPLICATION FUNCT.
1.8 FAULT MANAGEMENT
1.9 COMMUNICATION
1.10 DIAGNOSTICS
1.11 IDENTIFICATION
1.12 FACTORY SETTINGS
1.13 USER MENU
1.14 PROGRAMMABLE CARD
0A
Quick
ENT
NST CAN 0.0Hz
0.0A
1.14 PROGRAMMABLE CARD
Modbus add Prg C.
DATE/TIME SETTINGS
: 17
Code << >> Quick
Controller Inside card Modbus address
The
[Modbus add Prg C.]
(AMOA) parameter can be set in the
[1.14 PROGRAMMABLE CARD]
menu.
This setting can also be accessed in the
[1.9 - COMMUNICATION]
(
COM-)
menu,
[MODBUS NETWORK]
(
Md1-) submenu
.
efesotomasyon.com
21
Operation using the graphic display terminal
Setting the date and time
In the
[1.14 PROGRAMMABLE CARD]
menu,
[DATE/TIME SETTINGS]
sub-menu, you can set:
- the year
- the month
- the day
- the hours
- the minutes
Hour
NST CAN 0.00Hz
DATE/TIME SETTINGS
10 : 42
0.0A
Day
<<
11 / 03 / 2005
>> Quick
Minutes
Month
Year
Note: The date and time are not refreshed on this settings screen. The current date and time
[Date/Time]
(
CLO)
can be viewed in the
[1.2 MONITORING]
(
SUP-)
menu.
Note: It is not possible to change either the date or time format:
• The date cannot be displayed in the "year/month/day" format.
• The time cannot be displayed in the "10:42 am" format.
Note: It is not possible to configure changes between winter and summer hours.
22 efesotomasyon.com
Operation using the graphic display terminal
Example of a special program
The name of menu 1.14 has been customized.
The application parameters are edited in plain text and arranged in menus.
CYCLE IN PROGRESS
Current cycle
Current phase
Operation
Product
Duration
SETTINGS
Cycle selected
No. of phases
Phase selected
Operation sel
Duration sel
: 5
: 2
: dosing
: oil
: 30s
: 10
: 6
: 2
: mixing
: 120s
RUN APP +50.0Hz
1.14 DOSING
CYCLE IN PROGRESS
Current cycle : 5
2.1A
Current phase
Operation
Product
: 2
: dosing
: oil
Code << >> Quick
CYCLE IN PROGRESS
Current cycle
Current phase
Operation
Product
Duration
SETTINGS
Cycle selected
No. of phases
Phase selected
Operation sel
Duration sel
: 5
: 2
: dosing
: oil
: 30s
: 10
: 6
: 2
: mixing
: 120s
RUN
SETTINGS
Cycle selected
No. of phases
Phase selected
Operation sel
Code
APP +50.0Hz
1.14 DOSING
<< >> Quick
2.1A
: 10
: 6
: 2
: mixing efesotomasyon.com
23
Operation using the integrated display terminal
Factory-loaded program
Controller Inside menu
Power-up
XXX
Displays the state of the drive
ENT
ESC
SIM-
ESC
USr-
ESC
SPL-
ESC
COd-
ENT
ESC
ESC
LAC-
PROGRAMMABLE CARD
The
[Modbus add Prg C.]
(AMOA) parameter can be set, as in the (
COM-)
menu, (
Md1-)
sub-menu.
Note: It is not possible to set either the date or the time.
Special program
Controller Inside HMI words are displayed in the form (O01) to (O50) .
Lists are displayed in the format (EL1) to (EL20) .
24 efesotomasyon.com
atv71_Controller_Inside_EN_V1
2005-04
efesotomasyon.com
Atsisiųsti
Vieša nuoroda atnaujinta
Vieša nuoroda į jūsų pokalbį buvo atnaujinta. You may view and manage your chat links after registration here.
Dokumento vieša nuoroda
Reklama
