advertisement
PowerLite
®
822+/83+
Quick Setup
1
Unpack the projector
You should have the following items:
2
Connect your video source
Connect the projector to a computer or video source using any of the available connections shown below.
•
Check the connectors on your video equipment. If more than one connection is available, choose the one that provides the best quality.
The projector connectors from highest to lowest quality are
Computer (Component Video), S-Video, and Video.
•
A computer cable is included. You can purchase optional video and audio cables through Epson or an electronics store.
•
You can connect up to 4 video devices and use the remote control to switch between them.
S-Video cable
(optional)
RCA video cable
(composite video)
(optional)
Component video to
VGA cable
(optional)
Computer cable
(included)
3
Set up the remote control
1
Remove the battery cover.
2
Insert the batteries.
3
Replace the battery cover.
L-Audio-R ports
Audio2 and Audio1 ports
You can also connect an external monitor to watch the display on your computer monitor while watching the projection screen
(when the computer cable is connected to the Computer1 port). To enhance the sound in your presentation, you can connect external speakers. See the User’s Guide on your CD-ROM for instructions.
Projector Power cord
Remote control and batteries
User’s Guide
CD-ROM
Password Protected sticker
Computer cable
The remote control is ready for use.
Choose a location
The projector supports 4 viewing setups. Choose the best one for your environment. If you install the projector in a rear or overhead position, you’ll need to choose the correct projection option, identified below, from the Extended menu. See the User’s Guide on your CD-ROM for instructions.
Table
Convenient for temporary front projection.
Choose Front from the menu.
Ceiling
Professional installation recommended.
Choose Front/Ceiling from the menu.
Rear
For installation behind a translucent screen.
Choose Rear from the menu.
Rear/Ceiling
Professional installation recommended.
Choose Rear/Ceiling from the menu.
The distance between the projector and the screen determines the size of the image. The diagram below shows approximately how big your image will be (diagonally), based on where you set up the projector. (For more help determining the size of your image, try the Image Size Calculator on the Multimedia Projectors page on
Epson’s website.)
Turn over
PowerLite
®
822+/83+
Quick Setup
1
Unpack the projector
You should have the following items:
2
Connect your video source
Connect the projector to a computer or video source using any of the available connections shown below.
•
Check the connectors on your video equipment. If more than one connection is available, choose the one that provides the best quality.
The projector connectors from highest to lowest quality are
Computer (Component Video), S-Video, and Video.
•
A computer cable is included. You can purchase optional video and audio cables through Epson or an electronics store.
•
You can connect up to 4 video devices and use the remote control to switch between them.
S-Video cable
(optional)
RCA video cable
(composite video)
(optional)
Component video to
VGA cable
(optional)
Computer cable
(included)
3
Set up the remote control
1
Remove the battery cover.
2
Insert the batteries.
3
Replace the battery cover.
L-Audio-R ports
Audio2 and Audio1 ports
You can also connect an external monitor to watch the display on your computer monitor while watching the projection screen
(when the computer cable is connected to the Computer1 port). To enhance the sound in your presentation, you can connect external speakers. See the User’s Guide on your CD-ROM for instructions.
Projector Power cord
Remote control and batteries
User’s Guide
CD-ROM
Password Protected sticker
Computer cable
The remote control is ready for use.
Choose a location
The projector supports 4 viewing setups. Choose the best one for your environment. If you install the projector in a rear or overhead position, you’ll need to choose the correct projection option, identified below, from the Extended menu. See the User’s Guide on your CD-ROM for instructions.
Table
Convenient for temporary front projection.
Choose Front from the menu.
Ceiling
Professional installation recommended.
Choose Front/Ceiling from the menu.
Rear
For installation behind a translucent screen.
Choose Rear from the menu.
Rear/Ceiling
Professional installation recommended.
Choose Rear/Ceiling from the menu.
The distance between the projector and the screen determines the size of the image. The diagram below shows approximately how big your image will be (diagonally), based on where you set up the projector. (For more help determining the size of your image, try the Image Size Calculator on the Multimedia Projectors page on
Epson’s website.)
Turn over
PowerLite
®
822+/83+
Quick Setup
1
Unpack the projector
You should have the following items:
2
Connect your video source
Connect the projector to a computer or video source using any of the available connections shown below.
•
Check the connectors on your video equipment. If more than one connection is available, choose the one that provides the best quality.
The projector connectors from highest to lowest quality are
Computer (Component Video), S-Video, and Video.
•
A computer cable is included. You can purchase optional video and audio cables through Epson or an electronics store.
•
You can connect up to 4 video devices and use the remote control to switch between them.
S-Video cable
(optional)
RCA video cable
(composite video)
(optional)
Component video to
VGA cable
(optional)
Computer cable
(included)
3
Set up the remote control
1
Remove the battery cover.
2
Insert the batteries.
3
Replace the battery cover.
L-Audio-R ports
Audio2 and Audio1 ports
You can also connect an external monitor to watch the display on your computer monitor while watching the projection screen
(when the computer cable is connected to the Computer1 port). To enhance the sound in your presentation, you can connect external speakers. See the User’s Guide on your CD-ROM for instructions.
Projector Power cord
Remote control and batteries
User’s Guide
CD-ROM
Password Protected sticker
Computer cable
The remote control is ready for use.
Choose a location
The projector supports 4 viewing setups. Choose the best one for your environment. If you install the projector in a rear or overhead position, you’ll need to choose the correct projection option, identified below, from the Extended menu. See the User’s Guide on your CD-ROM for instructions.
Table
Convenient for temporary front projection.
Choose Front from the menu.
Ceiling
Professional installation recommended.
Choose Front/Ceiling from the menu.
Rear
For installation behind a translucent screen.
Choose Rear from the menu.
Rear/Ceiling
Professional installation recommended.
Choose Rear/Ceiling from the menu.
The distance between the projector and the screen determines the size of the image. The diagram below shows approximately how big your image will be (diagonally), based on where you set up the projector. (For more help determining the size of your image, try the Image Size Calculator on the Multimedia Projectors page on
Epson’s website.)
Turn over
4
Plug in and turn on
1
Open the A/V Mute slide
(lens cover).
2
Connect the power cord to the projector and plug the other end into an electrical outlet.
The Power light on the projector turns orange.
3
Turn on your computer or video source.
4
Press the Power button on the projector or remote control. The projector beeps, the Power light flashes green, and the projector lamp comes on in about 5 seconds.
The Power light stays green.
5
Start your video or presentation. If you have connected more than one video source, use the Source Search button on the projector or remote control to select the one you want to watch.
If your image does not appear on the screen, see the
Troubleshooting section for help.
Turning off the projector
1
If you’re using a computer, shut it down first, while you can still see the display.
2
Press the Power button on the projector or remote control.
3
When you see the confirmation message, press the Power button again. The projector beeps twice and the Power light turns orange.
With Epson’s Instant Off ready to travel.
® technology, there’s no cool-down period. When you’re done, just unplug the projector and it’s
5
Adjust the image
1
To raise the image, stand behind the projector, then press the foot release lever and lift the front of the projector. Release the lever to lock the foot in the position you want.
2
Rotate the focus ring to sharpen the image, and the zoom ring to enlarge or reduce it.
Zoom ring Focus ring
3
If your image looks like or , first make sure the projector is facing the screen squarely. Then, if necessary, press the or buttons on the projector’s control panel until the image is corrected.
4
To select the best color mode, press the Color Mode button on the remote control repeatedly to move through the options.
Color Mode button
See your User’s Guide on the CD-ROM for more information about image adjustments.
6
Install your User’s Guide and register your projector
1
Insert the PowerLite Projector CD-ROM in your drive. If the installer doesn’t open automatically, double-click the Epson CD-ROM icon, then double-click the Epson installer icon.
2
Choose your projector, then follow the instructions on the screen to register.
You can also register at www.epson.com/webreg.
3
After you register the projector, click User’s Guide to install it.
(If you don’t already have Adobe ® Reader, ® click Adobe Reader and follow the on-screen instructions to install it.)
4
When you’re done, click Exit.
To open your User’s Guide, double-click the PL 822+ 83+ User’s Guide icon on your desktop.
Where to get help
Internet support
Visit Epson’s support website at epson.com/support and select your product for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail
Epson with your questions.
Visit http://www.presentersonline.com to access tips, templates, and training for developing successful presentations.
Speak to a support representative
To use the Epson PrivateLine ® Support service, call (800) 637-7661 and enter the PIN on the included Epson PrivateLine Support card.
This service is available 6 AM to 6 PM , Pacific Time, Monday through
Friday, for the duration of your warranty period. You may also speak with a projector support specialist by dialing one of the following numbers. (Days and hours of support are subject to change without notice. Toll or long distance charges may apply.)
U.S.: (562) 276-4394, 6 AM to 6 PM , Pacific Time, Monday-Friday
Canada: (905) 709-3839, 6 AM to 6 PM , Pacific Time, Monday-Friday
Purchase supplies and accessories
You can purchase screens, carrying cases, and other accessories from an Epson authorized reseller. To find the nearest reseller, call
800-GO-EPSON (800-463-7766). Or you can purchase online at
www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Troubleshooting
If you see a blank screen
If you see a blank screen or the No signal message after turning on your computer or video source, check the following:
Make sure the Power light on the projector is green and not flashing and the A/V Mute slide (lens cover) is open.
Make sure the cables are connected correctly. (See the User’s Guide for more information.)
If you’ve connected more than one video source, you may need to press the Source Search button on the projector or the remote control to select the one you want to watch. (Allow a few seconds for the projector to sync up after pressing it.)
If the projector and the notebook don’t display the same image
If you’re using a Windows ® notebook:
Hold down the Fn key and press the function key (such as or CRT/LCD) that lets you display on an external monitor. On most systems, the or CRT/LCD key lets you toggle between the
LCD screen and the projector, or display on both at the same time.
Check your monitor settings to make sure both the LCD screen and the external monitor port are enabled. From the Control
Panel, open the Display utility. Click the Settings tab, then click
Advanced. The method for adjusting the settings varies by brand; you may need to click a Monitor tab, then make sure the external
Monitor port is set as your primary display and/or enabled. See your computer’s documentation or online help for details.
If you’re using a Macintosh ® notebook with OS X:
1 From the Apple ® menu, select System Preferences, then click
Display or Displays.
2 Select VGA Display or Color LCD, click Arrangement or Arrange, and make sure Mirror Displays is checked.
Epson and Instant Off are registered trademarks and Epson Exceed Your Vision is a trademark of
Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks and Epson Store is a service mark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
The contents of this manual are subject to change without notice.
© 2007 Epson America, Inc. 12/07
Printed in XXXXXX CPD-25115
4
Plug in and turn on
1
Open the A/V Mute slide
(lens cover).
2
Connect the power cord to the projector and plug the other end into an electrical outlet.
The Power light on the projector turns orange.
3
Turn on your computer or video source.
4
Press the Power button on the projector or remote control. The projector beeps, the Power light flashes green, and the projector lamp comes on in about 5 seconds.
The Power light stays green.
5
Start your video or presentation. If you have connected more than one video source, use the Source Search button on the projector or remote control to select the one you want to watch.
If your image does not appear on the screen, see the
Troubleshooting section for help.
Turning off the projector
1
If you’re using a computer, shut it down first, while you can still see the display.
2
Press the Power button on the projector or remote control.
3
When you see the confirmation message, press the Power button again. The projector beeps twice and the Power light turns orange.
With Epson’s Instant Off ready to travel.
® technology, there’s no cool-down period. When you’re done, just unplug the projector and it’s
5
Adjust the image
1
To raise the image, stand behind the projector, then press the foot release lever and lift the front of the projector. Release the lever to lock the foot in the position you want.
2
Rotate the focus ring to sharpen the image, and the zoom ring to enlarge or reduce it.
Zoom ring Focus ring
3
If your image looks like or , first make sure the projector is facing the screen squarely. Then, if necessary, press the or buttons on the projector’s control panel until the image is corrected.
4
To select the best color mode, press the Color Mode button on the remote control repeatedly to move through the options.
Color Mode button
See your User’s Guide on the CD-ROM for more information about image adjustments.
6
Install your User’s Guide and register your projector
1
Insert the PowerLite Projector CD-ROM in your drive. If the installer doesn’t open automatically, double-click the Epson CD-ROM icon, then double-click the Epson installer icon.
2
Choose your projector, then follow the instructions on the screen to register.
You can also register at www.epson.com/webreg.
3
After you register the projector, click User’s Guide to install it.
(If you don’t already have Adobe ® Reader, ® click Adobe Reader and follow the on-screen instructions to install it.)
4
When you’re done, click Exit.
To open your User’s Guide, double-click the PL 822+ 83+ User’s Guide icon on your desktop.
Where to get help
Internet support
Visit Epson’s support website at epson.com/support and select your product for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail
Epson with your questions.
Visit http://www.presentersonline.com to access tips, templates, and training for developing successful presentations.
Speak to a support representative
To use the Epson PrivateLine ® Support service, call (800) 637-7661 and enter the PIN on the included Epson PrivateLine Support card.
This service is available 6 AM to 6 PM , Pacific Time, Monday through
Friday, for the duration of your warranty period. You may also speak with a projector support specialist by dialing one of the following numbers. (Days and hours of support are subject to change without notice. Toll or long distance charges may apply.)
U.S.: (562) 276-4394, 6 AM to 6 PM , Pacific Time, Monday-Friday
Canada: (905) 709-3839, 6 AM to 6 PM , Pacific Time, Monday-Friday
Purchase supplies and accessories
You can purchase screens, carrying cases, and other accessories from an Epson authorized reseller. To find the nearest reseller, call
800-GO-EPSON (800-463-7766). Or you can purchase online at
www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Troubleshooting
If you see a blank screen
If you see a blank screen or the No signal message after turning on your computer or video source, check the following:
Make sure the Power light on the projector is green and not flashing and the A/V Mute slide (lens cover) is open.
Make sure the cables are connected correctly. (See the User’s Guide for more information.)
If you’ve connected more than one video source, you may need to press the Source Search button on the projector or the remote control to select the one you want to watch. (Allow a few seconds for the projector to sync up after pressing it.)
If the projector and the notebook don’t display the same image
If you’re using a Windows ® notebook:
Hold down the Fn key and press the function key (such as or CRT/LCD) that lets you display on an external monitor. On most systems, the or CRT/LCD key lets you toggle between the
LCD screen and the projector, or display on both at the same time.
Check your monitor settings to make sure both the LCD screen and the external monitor port are enabled. From the Control
Panel, open the Display utility. Click the Settings tab, then click
Advanced. The method for adjusting the settings varies by brand; you may need to click a Monitor tab, then make sure the external
Monitor port is set as your primary display and/or enabled. See your computer’s documentation or online help for details.
If you’re using a Macintosh ® notebook with OS X:
1 From the Apple ® menu, select System Preferences, then click
Display or Displays.
2 Select VGA Display or Color LCD, click Arrangement or Arrange, and make sure Mirror Displays is checked.
Epson and Instant Off are registered trademarks and Epson Exceed Your Vision is a trademark of
Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks and Epson Store is a service mark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
The contents of this manual are subject to change without notice.
© 2007 Epson America, Inc. 12/07
Printed in XXXXXX CPD-25115
4
Plug in and turn on
1
Open the A/V Mute slide
(lens cover).
2
Connect the power cord to the projector and plug the other end into an electrical outlet.
The Power light on the projector turns orange.
3
Turn on your computer or video source.
4
Press the Power button on the projector or remote control. The projector beeps, the Power light flashes green, and the projector lamp comes on in about 5 seconds.
The Power light stays green.
5
Start your video or presentation. If you have connected more than one video source, use the Source Search button on the projector or remote control to select the one you want to watch.
If your image does not appear on the screen, see the
Troubleshooting section for help.
Turning off the projector
1
If you’re using a computer, shut it down first, while you can still see the display.
2
Press the Power button on the projector or remote control.
3
When you see the confirmation message, press the Power button again. The projector beeps twice and the Power light turns orange.
With Epson’s Instant Off ready to travel.
® technology, there’s no cool-down period. When you’re done, just unplug the projector and it’s
5
Adjust the image
1
To raise the image, stand behind the projector, then press the foot release lever and lift the front of the projector. Release the lever to lock the foot in the position you want.
2
Rotate the focus ring to sharpen the image, and the zoom ring to enlarge or reduce it.
Zoom ring Focus ring
3
If your image looks like or , first make sure the projector is facing the screen squarely. Then, if necessary, press the or buttons on the projector’s control panel until the image is corrected.
4
To select the best color mode, press the Color Mode button on the remote control repeatedly to move through the options.
Color Mode button
See your User’s Guide on the CD-ROM for more information about image adjustments.
6
Install your User’s Guide and register your projector
1
Insert the PowerLite Projector CD-ROM in your drive. If the installer doesn’t open automatically, double-click the Epson CD-ROM icon, then double-click the Epson installer icon.
2
Choose your projector, then follow the instructions on the screen to register.
You can also register at www.epson.com/webreg.
3
After you register the projector, click User’s Guide to install it.
(If you don’t already have Adobe ® Reader, ® click Adobe Reader and follow the on-screen instructions to install it.)
4
When you’re done, click Exit.
To open your User’s Guide, double-click the PL 822+ 83+ User’s Guide icon on your desktop.
Where to get help
Internet support
Visit Epson’s support website at epson.com/support and select your product for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail
Epson with your questions.
Visit http://www.presentersonline.com to access tips, templates, and training for developing successful presentations.
Speak to a support representative
To use the Epson PrivateLine ® Support service, call (800) 637-7661 and enter the PIN on the included Epson PrivateLine Support card.
This service is available 6 AM to 6 PM , Pacific Time, Monday through
Friday, for the duration of your warranty period. You may also speak with a projector support specialist by dialing one of the following numbers. (Days and hours of support are subject to change without notice. Toll or long distance charges may apply.)
U.S.: (562) 276-4394, 6 AM to 6 PM , Pacific Time, Monday-Friday
Canada: (905) 709-3839, 6 AM to 6 PM , Pacific Time, Monday-Friday
Purchase supplies and accessories
You can purchase screens, carrying cases, and other accessories from an Epson authorized reseller. To find the nearest reseller, call
800-GO-EPSON (800-463-7766). Or you can purchase online at
www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Troubleshooting
If you see a blank screen
If you see a blank screen or the No signal message after turning on your computer or video source, check the following:
Make sure the Power light on the projector is green and not flashing and the A/V Mute slide (lens cover) is open.
Make sure the cables are connected correctly. (See the User’s Guide for more information.)
If you’ve connected more than one video source, you may need to press the Source Search button on the projector or the remote control to select the one you want to watch. (Allow a few seconds for the projector to sync up after pressing it.)
If the projector and the notebook don’t display the same image
If you’re using a Windows ® notebook:
Hold down the Fn key and press the function key (such as or CRT/LCD) that lets you display on an external monitor. On most systems, the or CRT/LCD key lets you toggle between the
LCD screen and the projector, or display on both at the same time.
Check your monitor settings to make sure both the LCD screen and the external monitor port are enabled. From the Control
Panel, open the Display utility. Click the Settings tab, then click
Advanced. The method for adjusting the settings varies by brand; you may need to click a Monitor tab, then make sure the external
Monitor port is set as your primary display and/or enabled. See your computer’s documentation or online help for details.
If you’re using a Macintosh ® notebook with OS X:
1 From the Apple ® menu, select System Preferences, then click
Display or Displays.
2 Select VGA Display or Color LCD, click Arrangement or Arrange, and make sure Mirror Displays is checked.
Epson and Instant Off are registered trademarks and Epson Exceed Your Vision is a trademark of
Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks and Epson Store is a service mark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
The contents of this manual are subject to change without notice.
© 2007 Epson America, Inc. 12/07
Printed in XXXXXX CPD-25115
advertisement
Related manuals
advertisement