Owner's Manual
Vacuum Cleaner
Model 116,22512
116.22513
CAUTION:
Read and follow all safety and operating
instructionsbefore first
use of this product°
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com
Part No. CO1ZBPKOOUO_-8192043
Printed in U.S_A.
Before Using Your New Vacuum .......
2
KenmoreVacuum Cleaner Warranty _ _ 2
Important Safety Instructions ................. 3
Parts and Features ..................
4-5
Assembly Instructions ..............
6-7
Use ...............................
How to Start ........................
Vacuuming Tips ........................
Suggested Pile Height Settings .........
Attachments ........................
Attachment Use Chart ................
Performance Features ...............
9
9
10
10
11
8
8
Canister Care .......................
12
Bag Changing .....................
t2
Cleaning Exterior and Attachments .....
t3
Motor Safety Filter Changing ..........
Exhaust Filter Changing
..................
13
14
Power-Mate ® Care ...................
14
Light Bulb Changing ....................
15
Belt Changing and Brush Cleaning ..... 15-t6
Brush Servicing ..................
17
Brush Assembly ....................
17
Troubleshooting .....................
Requesting Assistance
Or Service .................
18
Back Cover
Please read this guide.
It will help you assemble and operate your new Kenmore vacuum in the safest and most effective way,
For more information about vacuum cleaner care and operation, call your nearest Sears store,
You will need the complete model and serial numbers when requesting information. Your vacuum's model and serial numbers are located on the Model and Serial Number Plate,
Use the space below to record the model number and serial number of your new Kenmore vacuum,
Model No.
Serial Noo
Date of Purchase
Keep this book and your sales check (receipt) in a safe place for future reference.
LIMITED ONEYEAR WARRANTY ON KENMOREVACUUM CLEANER
This warranty is for one year from the date of purchase, and includes only private household vacuum cleaner use, During the warranty year, when this vacuum cleaner is operated and maintained according to the owner's manual instructions, Sears will repair any defects in material or workmanship free of charge
This warranty excludes vacuum bags, belts, light bulbs, and filters, which are expendable parts and become worn during normal use.
For warranty service, return this vacuum cleaner to the nearest Sears Service Center in the United States.
This warranty applies only while this product is in use in the United States. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state,
Sears, Roebuck and Coo, D1817 WA, Hoffman Estates, IL 60179
WARNIN
Your safety is important to us. To reduce the risk of fire, electrical shock, injury to persons or damage when using your vacuum cleaner, foltow basic safety precautions including the following:
Read this manual before assembling using your vacuum cleaner.
or tured hose° The hose contains electrical wires.
Replace if cut or worn° Avoid picking up sharp objects.
Use your cleaner only as described in this manual Use only with Sears recommended attachments.
To reduce the risk of electrical shock - Do not use outdoors or on wet surfaces.
Do not use with any opening blocked; keep free of dust, lint, hair and anything that may reduce air flowo
Disconnect electrical supply before servicing or cleaning out brush area. Failure to do so could result in electrical shock or brush suddenly starting.
Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts_
Do not use cleaner without dust bag and/or
_ters in place.
Always turn cleaner off before connecting or disconnecting the hose or Power-Mate®_
Always turn cleaner off before unplugging_
Do not unptug by puffing on cord.. To unplug, grasp the plug, not the cord.
Always change the dust bag after vacuuming carpet cleaners or freshener, powders and fine dust. These products clog the bag, reduce airflow and can cause the bag to burst. Failure to change bag could cause permanent damage to the cleaner.
Hold plug when rewinding onto cord reel.
Do not allow plug to whip when rewinding.
Do not use with damaged cord or plug.. If cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a Sears
Service Center.
Do not use the cleaner to pick up sharp hard objects, small toys, pins, paper clips, etco They may damage the cleaner or dust bag.
Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
Do not pull or carry by cord, use cord as a handle, dose door on cord, or pull cord around sharp edges or corners.
Do not run cleaner over cord_ Keep cord away from heated surfaces.
Do not leave cleaner when plugged in.
Unplug from outlet when not in use and before servicing.
Do not use cleaner to pick up flammable or combustible liquids (gasoline, cleaning fluids, perfumes, etc.), or use in areas where they may be present, The fumes from these substances can create a fire hazard or explosion.
Do not allow to be used as a toy. Close attention is necessary when used by or near children..
Use extra care when cleaning on stairs. Do not put on chairs, tables, etc. Keep on floor.
Do not handle plug or cleaner with wet hands.
You are responsible for making sure that your vacuum cleaner is not used by anyone unable to operate it properly.
Do not put any objects into openings_
Do not operate the cleaner with a punc-
Do not operate without exhaust filter or exhaust filter cover installed.
SAVE THESE INSTRUCTIONS
Proper assembly and safe use of your vacuum cleaner are your responsibilities.
Your cleaner is intended only for household use° Read this Owner's Manual carefully for important use and safety information. This guide contains safety statements under warning and caution symbols_
Please pay special attention to these boxes and follow any instructions given. WARNING statements alert you to such dangers as fire, electrical shock, burns and personal injury CAU.
TION statements alert you to such dangers as personal iniurv a£d/or property dama.qe_...............
3 gN k_,_t_4N
It is important to know your vacuum cleaner's parts and features to assure its proper and safe use. Review these before using your cleaner.
;_4-Cord and
Plug Holder
Upper
Cord and
Cord Holder
Wand
_-- Power.Mate ®
Power Cord
Wand Swivel
Cord Holder o o
Belt
tn UoS, #20.5285
tn Canada #40110
POWER-MATEs
Wand Quick
Release Pedal
(Some Models)
Power.Mate ®
Model/Serial Numbers
(On Bottom)
Handle
Release//
Pedal "
/
1t!
Pile Height Pedal
(Some Models)
Pile Height Indicator
(Some Models)
Headlight and Lens
Bulb
(Some Models)
In Canada #596181
. LlghtCover
Cleaner
(Not Shown)
OverloadProtector
(ResetButton)
4
HOSE
3-Way On/Off Switch
Off/Bare Floor/Carpet
(Some Models)
Speed
Control
(Some
Models)
Handle
Crevice
Toot
Combination
Brush
ATTACHMENTS
IL-L-----J
Power-Mate Jr,=
(Some Models)
1
Floor
Brush
Hose Swivel t
Handi_Mate Jr.'_
(Some Models)
NOTE: All models have one set of attachments in the canister, Some models have an additional set, which can be kept in the accessory bag for garage use.
CANISTER
Attachment
Storage
Canlster
Cord Rewind
Button
Exhaust Filter Cover
(Exhaust Filter Inside)
Performance
Indicator
(Some Models)
Hood
Release
Bag HoMer
Dust Bag
Motor Safety Filter
(Behind Dust Bag)
]
Cord
, i n,l,lu,,i,,H,n ii,
WARNING
Electrical Shock Hazard ii,
DO NOT plug into electrical supply until assembly is complete, Failure to do so could result in electrical shock or injury.
,, ,,,,,, , ,, ,,, ,,, , , , ,
Before assembling vacuum, check the
PACKING LIST on the cover of the separate
Repair Parts List. Use this list to verify that you have received all the components of your new Kenmore vacuum.
WANDS
Slide wands together until wand button snaps into place,
Turn wand button
to the slotted area of the wand swivelr
The swivel allows you to turn the handle to the left side to reach farther under low furniture.
Swivel --
Wand
Cord
Holder f
POWER-MATE ®
1. insert wands into Power-Mate ® until the wand buttons snaps into place.
Raised
Area
2. Connect Power-
Mate_plug and cord as shown,
DO NOT force.
Raised area of plug must be
toward hand,
3. Secure cord into cord holder on wand swivel.
To remove; Disconnect cord and step on wand release pedal, then pull up on wands.
Handle
6
Wand
Swivel
Wand o_
__j
Wand
Button
CANISTER
1. Open the canister hood.
2. Check to see that the dust bag is proper-
ly in,stalledo See BAG CHANGING for instructions,
3. Check to see that the motor safety filter is properly installed,, See MOTOR SAFETY
FILTER CLEANING for instructions,
HOOD
It is normal for the canister hood to come off when opened further than needed° Line up the hinge slots, insert them, and close the hood to replace it.
HOSE
Latch
1. Line up the hose latch tab and notch in canister hood and insert hose into canister until it snaps in place_
To remove: Lift hose latch tab upward and pull up on hose°
Handle
2. Insert handle into wand until lock button snaps in place° Be sure hose is not twisted_
To remove: Press handle release button and pull up on handieo
To store: Disconnect hose from wands and canister to prevent stress on hose during storage.
Store hose in a loosely coiled position so the hose covering is not stressed.
Hose
F.
Hose
Latch Tab
Cover
Hood
Re_ase
DustBag
Attachment
Storage
!
HOW TO START
Personal Injury and Product Damage
Hazard
• DO NOT plug in if switch is in ON position.
Personal injury or damage could result.
• The cord moves rapidly when rewinding.
Keep children away and provide a clear path when rewinding the cord to prevent personal injury.
• DO NOT use outlets above counters.
Damage from cord to items in surrounding area could occur.
i i1,111 i i i iiiii I
Pile Height
Indicator
Handle Release
Pedal
3. Lower wand from upright position by pressing on the handle release pedal.
CAUTION
DO NOT leave the Power-Mate ® running in one spot in the upright
position for any length of time.
Damage to carpet may occur.
_: 1. Pull cord out of canister to desired length. The cord
0_ will not rewind until button is pushed,
4. Select a pile height setting by pressing
the small pedal on the rear of the Power-
Mate% The pile height setting shows on the indicator, See SUGGESTED PILE HEIGHT
SETTINGS.
Attention: Refer to your carpet manufac-
turers cleaning recommendations.
Some more delicate carpets may require that they be vacuumed with the Power-Mate ® agitator turned off, to prevent carpet damage.
NOTE: To reduce the risk of electric shock,
this vacuum cleaner has a polarized plug, one blade is wider than the other. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way,
2. Plug the polarized power cord into a 120
Volt outlet Iocated near the floor.
To rewind: Unplug the cleaner. Hold the plug while rewinding to prevent damage or injury from the moving cord. Push cord rewind bar_
5. Select a switch position on the handle.
OFF
FLOOR - turns on the canister motor only.
CARPET - turns on both the canister and the Power-Mate ® motors.
Suggested sweeping pattern.
For best cleaning action, the Power-Mate ® should be pushed straight away from you and pulled straight back, At the end of each pull stroke, the direction of the Power-Mate ® shouid be changed to point into the next section to be cleaned, This pattern should be continued across the rug with slow, gliding motions,
NOTE: Fast,
jerky strokes do not provide complete cleaning
The hose swivel allows the hose to turn without moving the canister. This is helpful for cleaning in small areas.
Check hose for twisting before pulling canister.
Suction
Control
Carpeted stairs need to be vacuumed regularly° For best cleaning results, fu!ly
close the suction control.
WARNING
Personal Injury Hazard
Use care if canister is placed on stairs, if it falls, personal injury or property damage could result.
For best cleaning results, keep the airflow passage open.
Check each assembly area in HOW YOUR VACUUM
WORKS occasionally for clogs, Unplug from outlet before checking.
•
CAUTION
To prevent tip over, never leave
Power-Mate ® on or in the upright position.Turning
the handle to one
side will make the Power-Mate ®more stable and less likely to tip over.
For best deep down cleaning, use the XLO setting. However, you may need to raise the height to make some jobs easier, such as scatter rugs and some deep pile carpets, and to prevent the vacuum cleaner from shutting off. Suggested settings are:
HI - Shag, deep pile, or scatter rugs_
MED - Medium to deep pileo
LO - Low to medium pile.
XLO - Most carpets and bare floors.
ATTACHMENTS ON WANDS
1, To remove wands from Power-
Mate ®, lock wands
in straight-up position_
ill
ATTACHMENTS ON HANDLE
Handle
Button -_ U
NOTE: If the
Power-Mate ® is attached, turn cleaner off before removing handle from wands.,
Upper
B===
_
1. Press lock button, then pul!
to remove handie from wand,
Wand V If your model has the optional feature of a handle release, press it in similarly.
2. Slide attachments firm-
ly on handle as needed.
See chart below° m
Wand Quick
Release Pedal am
2. Press wand release pedal with foot and pull the wands straight up out of
Power-Mate ®,
The Power-Mate _' plug and cord do not have to be removed to use attachments on the wands.
3. Put attach-ments on wands as needed. See chart below.
CLEANING
AREA
ATTACHMENT
Furniture*
Between
Cushions*
Drapes*
Stairs
Bare Carpeted
Floors FloorstRugs
Walls
Combination Brush
(Some Models)
Crevice Tool
(Some Models)
Floor Brush
(Some Models)
Power-Mate •
(Some Models)
Handi-Mate Jr. ®
(Some Models)**
Power-Mate Jr, ®
(Some Models)**
X
X x
X
X X
X
X x
X
X*** x
X
X
*Always clean attachments before using on fabrics,. '" 3-way On!Off switch should be in FLOOR position
'** HandFMate Jr,®and Power-Mate Jr._ attachment instructions are tnciuded with the products * ** (Some Models)
Power-Mate switch should be in OFF position
NOTE= When separating wands, depress lqck button completely before p ullin_wands apart. If wand lock button is difficult to depress push the two wanas more lightly [ogmner to _ine up the ock button w th the hoe.
Depress ock button and then pull wands apart.
10
Activebrushedge cleanersareon both sidesof the Power-
Mate®.Guideeither
sideof the Power-
Mate®alongbaseboardsor nextto furnitureto help removedirttrappedat carpetedges,
OVERLOAD PROTECTOR
The Power-Mate ®has built-in protection against motor and belt damage should the brush jam. If the brush slows down or stops, the overload protector button pops up and shuts off the Power-
MateS° The canister motor will continue to run,
To correct problem: See
TROUBLESHOOTING.
To reset: Push in the overload protector button°
SUCTION CONTROL
The suction control allows suction suction you to change the vacuum suction for different fabric and carpet weights Opening the control decreases suction for draperies and lightweight rugs, while closing the control increases suction for upholsteries and carpets.
WARNING
Personal Injury Hazard
Always unplug the vacuum cleaner before cleaning the brush area as brush may suddenly restart.
Failure to do so can result in personal injury.
PERFORMANCE
INDICATOR
SOME MODELS if the performance indicator turns entirely red check for a full dust bag, or a clog in the vacuum. See HOW YOUR VACUUM
WORKS
NOTE; The performance indicator may ............
turn red when using attachments or when _#;_.
cleaning new carpet, due to reduced air#_F_' flow by the attachments themselves or _;,_,,_i_ new carpet fuzz filling the bag quickly.
,!,i_:,"._
POWER-MATE®STORAGE
SOME MODELS
....
The lower wand has a "U" shaped flange in the area where the power cord attaches_
The base has a "U" shaped slot near the front caster.
The slot allows the
wands and Power-
Mate ®to be stored with the canister to conserve storage space, The canister must be stored on end for this feature to be used.
The wand will slip out of the slot as it is lifted up for use and will slide into the slot as it is lowered for storage_
11
THERMAL PROTECTOR
This vacuum has a thermal protector which automatically trips to protect the vacuum from overheating The thermal protector turns the motor off automatically to allow the motor to cool in order to prevent possible damage to the vacuum°
To reset: Turn off and unplug the vacuum from the outlet to allow the vacuum to cool.
Check for and remove any clogs.
Also
check and replace any clogged filters.
Wait approximately 50 minutes and plug the vacuum in and turn back on to see if the thermal protector has reset. In some
cases, the unit may suddenly restart. DO
NOT leave unattended.
Thevacuumcleanercreatessuctionthat picksup dirt,Rapidlymovingair carries the dirt to the dustbagthroughthe
airflow passages° The dust bag lets _
/S._.
the air pass through, while it traps
t,edirt
For best cleaning results, keep _/" the airflow passage open /**_'
Check the starred areas occasionally for ctogs_ i4y
,/_y"
///
,_.,,"
Unplug from outlet _
"
/
/_
_ _
\ _.
.k._,._
_
Mofor safety
Filter
\
Exhaus
Filter
BAG CHANGING
For best cleaning results, the dust bag should be changed often. The performance indicator (some models) will specify when the dust bag needs to be changed or the airflow is blocked. NOTE: See PARTS AND
FEATURES for Bag Number.
1. Unplug cord from wall outlet,
2. Remove hose from canister.
3. Pull hood release out and up, then lift canister hood.
4, Disengage cardboard tab from red bag mount by pulling away and lifting up_
5. Pull bag out of the red bag mount.
"_j
-_
"_
Mofor_
F,ter : / ///!// /////
6. Check and replace, if necessary, the motor safety
_ter,
7. The red bag mount will flip forward after removing bag.
8. Rotate red bag mount down and install bag into slots per intructions pushing down until the cardboard tab locks into position and the holes align, Tuck the bag securely into the bag cavity so that none of it is able to be pinched by the hood,
9. Replace and latch canister hood,
10. Insert hose into canister.
11. Plug cord into wall outlet,
E
•
CAUTION
NEVER REUSE A DUST BAG.Very fine materials, such as carpet fresh-
ener, face powder, fine dust, plaster,
soot, new carpet lint, etc. can clog
the bag and cause it to burst before
it is full and may cause damage to vacuum motor.
Change bag more often when vacuuming these materials.
12
1. Unplug cord from wall outlet, DO NOT drip water on cleaner.
2. Clean exterior using a clean, soft cloth that has been dipped in a solution of mild liquid detergent and water, then wrung dry.
Wipe dry after cleaning.
3. To reduce static electricity and dust buildup, wipe outer surface of cleaner and attachments.
!
. CAUT,ON
Do not use attachments ifthey
are wet. Attachments used in dirty areas, such as under a refrigerator, should not be used on other surfaces until they are washed.They
could leave marks.
,fill change when dirty.
1, Lift the rubmotor safety
_ter as shown.
Electrical Shock Hazard
Unplug power cord from electrical outlet.
Do not operate the cleaner without the motor safety filter.
Be
sure the filter is dry and properly installed to prevent motor failure and/or electrical shock.
ill i
Remove the bag as outlined in the BAG
CHANGING section.
MOTOR SAFETY FILTER
ELECTROSTATIC
This white and grey filter must be replaced when dirty.
It should be replaced regularly depending on use conditions.
The filter
CANNOT be washed as it will lose its dust trapping ability,
2. Replace the filter, white side out, by sliding it back into place under the ribs in the bag cavity.
Tuck filter in so that it fits completely under the rubber retainer.
3. Replace the bag as outlined in the BAG
CHANGING section.
!
NEVER REUSE A DUST BAG.Very
fine materials, such as carpet fresh-
ener, face powder, fine dust, plaster,
soot, new carpet lint, etc. can clog the bag and cause it to burst before
it is full. Change bag more often when vacuuming these materials.
iJl ILI_
13
E
• WARNING
Fire and/or Electrical Shock Hazard
Do not operate with a clogged exhaust filter or without the exhaust filter or exhaust filter cover installed,
EXHAUST FILTER
HEPA
The exhaust filter cartridge must be replaced when dirty° Replace the filter when the entire surface area is covered evenly.
The filter CANNOT be washed as it will lose its dust trapping ability.
Replacement exhaust filters are available through Sears Service Center under part
no. 86880. See "Requesting Assistance or Service"
1, Pull out and up on the exhaust filter cover to remove from the motor cover and lay aside,
Exhaust\'_ _
Filter _
3o Place the new filter into the motor cover with the grey edge down.
2. When the exhaust filter becomes dirty, remove it by pulling straight up,
Exhaust
Filter
4. Reinstall the exhaust filter cover by inserting the tab into the slot in the motor cover°
Press firmly to snap exhaust filter cover into place,
Always follow all safety precautions when cleaning and servicing the Power-Mate ®.
E
• WARNING
Electrical Or Personal Injury
Hazard
Disconnect electrical supply before servicing or cleaning the unit,
Failure to do so could result in elec- trical shock or personal injury from cleaner suddenly starting.
14
1. Remove light cover by pressing in and lifting both sides as shown.
Push In _
And Turn ["_._
-._..
2. Push in and turn bulb counterclockwise to remove.
_---___t 3. Replace the bulb,, higher than t5 Watts
(130V)o Close light
__ places
NOTE: See PARTS AND FEATURES for
Bulb #.
_o_
E CAUTION
When you remove the end caps, a small metal washer on each end may come off. DO NOT lose these two metal washers.
TO CLEAN AGITATOR:
NOTE: In order to keep cleaning efficiency high and to prevent damage to your vacuum, the agitator must be cleaned every time the belt is changed.
The agitator must also be cleaned according to the following schedule:
Vacuum Use
Clean A_itator
HEAVY -
(used daily)
MODERATE -
(used 2_3 times/week)
LIGHT -
(used I time/week) every week every month every 2 months
Remove any dirt or debris in the belt path area or in the brush roller area.
IMPORTANT
Carefully remove any string or debris located on the agitator, end caps, washers or agitator shaft,
Replace the washers and the end caps,
See the exploded view for correct assembly.
Disconnect cleaner from electrical outlet.
Check and remove hair, string and lint build-
® up frequently in the Power-Mate agitator and end cap areas. If build-up becomes
® excessive, disconnect Power-Mate from wand and follow the steps below_
15
TO REMOVE BELT
1o Remove light cover and light bulb as shown under LIGHT BULB
CHANGING,
2. Unscrew the Power-
Mate ® cover screws_
3. Turn
Power-Mate ® ever, To remove cover, insert screwdriver at cover tabs on both sides and twist to release tabs.
Tab
4. lurn Power-
Mate ® right side up, Press handle release pedal and lower the swivel Rotate cover forward from back until front snaps free.
5. Carefully insert and lift screwdriver at each brush support to free brush from base,,
6. Remove worn belt.
Brush
Support
7. SIide brush supports off to check and clean brush support areas, See
BRUSH
ASSEMBLY for picture of complete brush assembly,,
TO REPLACE BELT
1. Slide washers and brush supports onto brush assembly.
2. Install new belt over motor drive, then over brush sprocket,
NOTE: See
PARTS AND
FEATURES for Belt #_
Brush
Support
Brush
MoOr
Ddve
Brush Sprocket
3. Snap brush supports into place on base,
Be sure brush supports are not upside* down,,
4. Line up front of cover and base,
Rest cover on front edge of base as shown.
Cover
Base
5. Rotate cover back. Press cover firmly until side tabs snap
into place.
Replace cover screws, light bulb and light cove r.
16
E
• WARNING
TO REPLACE BRUSH DOWEL
.........................
1. Remove Power-Mate ®cover, belt and
Electrical Shock Or Personal Injury
Hazard brush assembly, See "To Remove Belt" in
BELT CHANGING AND BRUSH
CLEANING..
Disconnect electrical supply before servicing or cleaning the unit.
Failure to do so could result in elec-
trical shock or personal injury from
2. Remove brush supports, washers, screws, end brush, brush sprocket pieces from ends of brush assembly_ cleaner suddenly starting,
TO CHECK BRUSHES
3. Reassemble brush assembly. To line up screw holes in dowel, sprocket and end brush, be sure the brush portion of end brush lines up with brushes on brush dowel
4. Replace belt, brush assembly, Power-
Mate®cover, light bulb and light cover. See
"To replace belt" in BELT CHANGING AND
BRUSH CLEANING.
__.__=__IF are worn to the level of the base support bars, replace the brush dowel.
Base Support Bars
_Washer
End
Cap
Agitator Unit
Brush
Sprocket
Flange
End
Brush
Screw
End
Cap
Brush Sprocket
Screw i
Washer
17
needed,otherthanthosedescribedin this owner'smanual,shouldbe performedby a Sears authorizedservicerepresentative.
WARNING
Electrical Shock Hazard
or cleaning the unit.
Failure to do so could result in electrical shock or personal injury.
Cleanerwon't start.
Poor job of dirt pick-up,
Cleaner starts but
cuts off.
Power-Mate=wlll not run when attached,
Performance indicator, some models, is red.
2.
3+
4.
Unpluggedat walloutfet.
Trippedcircuit breaker/blownfuse at household service panel,
Loosehose electrical connections
Tripped thermal canister
2.
3.
4.
5.
Full or clogged dust bag
Cbgged airflow passages
Dirty filters.
Wrong pile height setting
6,
7,
8+
9.
10.
Opensuction control
HoleInhose
Worn or broken bait,
Dirty brush or brush supports.
Canisterhood open. t.
Hoseor hood efectrical conneclians
2_
Tripped overload proteclor in
Power-Mate®,,
1,.
2.
3,
4,
Plug in firmly, push ON/OFF switch to ON
Reset circuitbreaker or replacefuse
Reconnect hose ends, (page 7),
Reset thermalprotector,(page 11).
1,
2.
Change bag, (page13),
Clear aidiow passages, (page 13).
3,
4.
Clean!changefilters, Ipage 14, 15)
Adjust setting, (pageg),
5.
6o
Adjust control, (page 12)
Replace hose.
7.
8 & 9,
Change brushes, (page !8)
See BELT CHANGING AND BRUSH
10,
CLEANING, (pages t6, 17)
Close and falch hood
1.
Check connections, reconnect hose ends, (page7)
2o Removeany items thatmay be caught
3.
or jammed, then reset If cleaner starts and stops again, clean brush and brush supports, then reset, (pages 16, 17).
Reset thermal protector,(page ! I),
3_
Tripped lhermal protector in canister t-
Power-Mate"connections
2_
3o
4_ unplugged,
Worn or broken belt,
Dirtybrush or brush suppods.
Trappedoverloadproteclor in
2o
3,
4.
Dirtyfitters,
Clogged eidlow passage
Certain attachment tools.
I,
Plugin lirmly,
2 & 3.
See BELT CHANGING AND BRUSH
4.
CLEANING, (pages 16, 17).
Check brush area for excessive lint build-upor jamming. Clean brush and brush supports, then reset, (pages !6, 17)
I.
Change bag, (page 13).
2.
3,
4.
Cfearv'changefilters,(page I4, 15)
Clear clog from airflowpassage, (page 13)
This is normal,Redshould disappear when tootis removed
1.
2,
Adjust setting, (page9)
Opensuction control,(page 16)
Cleaner picks up moveable
rugs -or., Power-Mate= pushes too hard.
Light won't work,
Cord won't rewind.
Cleanerleaves marks on carpet.
Wrong pile height setting.
Suction toostrong
1.
2.
Dirty power cord
Cordjammed
1.
Wrongvacuuming pattern,
1.
1.
2.
1.
Change light bulb, (page 16)
CIean the powercord
Pullcut cord and rewind.
See VACUUMINGTIPS, (page 9)
18
k
For
repair of major brand appliances in your own home...
no matter who made it, no matter who sold it!
1-800-4-MY-HOM E® Anytime, day or night
(1_800-469-4663) (UoS°Aoand Canada) www.sears°com www,sears.ca
For repair of carry-in products like vacuums, lawn equipment, and electronics, call for the nearest Sears Parts and Repair Center.
1-800-488-1222
Anytime, day or night (U.S.A. only) www, sears,com
For the replacement parts, accessories and owner's manuals that you need to do-it-yourself, call Sears PartsDirectSM!
1-800-366-PART
(1-800-366-7278)
6 a.m° - 11 p.m, 7 days a week
(U.S.A. only) www,sears.comipartsdlrect
To purchase or inquire about a Sears Service Agreement or Sears Maintenance Agreement:
1-800-827-6655 (U.S.A.)
7 a.m. - 5 p.m., CST, Mort° - Sat.
1-800-361-6665 (Canada)
9 a.m. - 8 p.m. EST, M -.. F, 4 p.m. Sat.
Pare pedir servicio de reparacidn a domicilio, y pare ordenar piezas:
1.-888-SU-HOGAR sM
(I-888-784-6427)
Au Canada pour service en franc,,ais:
1.800-LE-FOYER Mc
(1-800-533-6937) wwwosears_ca
© Sears, Roebuck and Co,
® RegisteredTrademark/ -r_Trademark/ SMService Mark of Sears, Roebuckand Co.
®Marca Registrads1TMMarca de Fdbrica t SM Marcade Ssrvtcfode Sears,Roebuckand Co.
McMarquede commerce/ MDMarqued_pos_ede Sears,RoebuckandCo.
