Arrow GS83 C, VGS83 B storage building Owner's Manual & Assembly Instructions

RE01

Owner's Manual & Assembly Instructions

Model No.

GS83-C VGS83-B

697.68600

Missing Parts, Questions on Assembly?

Call: 1-800-851-1085 or [email protected]

Do not return to dealer, they are not equipped to handle your requests.

712010111

Storage Area: 23 Sq. Ft.

2,1 m 2

122 Cu. Ft.

3,5 m 3

CAUTION: SOME PARTS HAVE SHARP EDGES. CARE

MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES

TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ

SAFETY INFORMATION PROVIDED IN THIS MANUAL

BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES

WHEN HANDLING METAL PARTS.

BUILDING DIMENSIONS * Size rounded off to the nearest foot

Exterior Dimensions Interior Dimensions Door

*Approx. Base (Roof Edge to Roof Edge) (Wall to Wall) Opening

Size Size Width Depth Height Width Depth Height Width Height

8' x 3' 96 7/8" x 38" 99 3/8" 39 1/4" 65 5/8" 94 1/8" 35 3/16" 64 7/16" 50 1/4" 59 3/4"

2,4 m x 0,9 m 246,1 cm x 96,4 cm 252,4 cm 99,7 cm 166,7 cm 239,1 cm 89,4 cm 163,7 cm 127,6 cm 151,8 cm

BEFORE YOU BEGIN....

A2

Owner's Manual

Before beginning construction, check local building codes regarding footings, location and other requirements. Study and understand this owner's manual.

Important information and helpful tips will make your construction easier and more enjoyable.

Assembly Instructions: Instructions are supplied in this manual and contain all appropriate information for your building model. Review all instructions before you begin, and during assembly, follow the step sequence carefully for successful results.

Flooring and Anchoring: Your storage building must be anchored to prevent wind damage. A base is necessary to construct a square and level building. Anchoring and base materials are not included with your building. We recommend the combined use of an Arrow Floor Frame Kit and an Arrow Anchoring Kit as an effective method of securing your building to the ground (Available by mail order or at your local dealer) or you may construct a base and anchoring system of your choice. Your assembly instructions provide information on a few methods commonly used to secure and level a storage building.

Parts and Parts List: Check to be sure that you have all the necessary parts for your building.

•All part numbers can be found on the parts. All of these numbers (before the -) must agree with the numbers on the Parts List page.

•If you find that a part is missing, include the model number of your building and contact:

Arrow Shed, LLC Customer Service Department

1101 North 4th Street Breese, Illinois 62230

1-800-851-1085 or [email protected]

•Separate contents of the carton by the part number while reviewing parts list. The first few steps show how to join related parts to make larger sub assemblies which will be used later.

•Familiarize yourself with the hardware and fasteners for easier use during construction. These are packaged within the carton. Note that extra fasteners have been supplied for your convenience.

PLAN AHEAD....

A3

Watch the Weather: Be sure the day you select to install your building is dry and calm.

Do not attempt to assemble your building on a windy day. Be careful on wet or muddy ground.

Teamwork: Whenever possible, two or more people should work together to assemble your building. One person can position parts or panels while the other is able to handle the fasteners and the tools.

Tools and Materials: These are some basic tools and materials you will need for the construction of your building. Decide which method of anchoring and the type of base you wish to use in order to form a complete list of the materials you will need.

Required

• Eye Goggles

• No. 2 Phillips Screwdriver

(With Hardened Magnetic Tip)

Note: A power screwdriver or variable speed drill with Phillips-tip attachment can speed assembly by as much as 40%.

Required

• Work Gloves

• Step Ladder

• Utility Knife / Scissors

• Pliers

• Carpenter's Level

• Tape Measure

Optional Time-Savers

• Wrench / Nut Driver

• Electric / Cordless Drill

• Square

• String (for squaring frame)

Base Preparation

• Hammer and Nails

• Spade or Shovel

• Hand Saw / Power Saw

• Lumber and/or Concrete

Selecting and Preparing Your Site: Before assembly, you will want to decide on a location for your building. The best location is a level area with good drainage.

•Allow enough working space for ease of moving parts into position during assembly. Be sure there will be enough space at entrance for doors to open fully and enough space around the building to be able to fasten the panel screws from the outside.

•Before you begin the first steps in assembling your parts, a base should be constructed and an anchoring system should be ready to use.

SAFETY FIRST....

A4

Safety precautions are important to follow throughout the construction of your building.

•Care must be taken when handling various pieces of your building since some contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your building.

•Practice caution with the tools being used in the assembly of this building. Be familiar with the operation of all power tools.

safety edge sharp edge sharp edge safety edge

•Keep children and pets away from worksite to avoid distractions and any accidents which may occur.

•Do not attempt to assemble the building if parts are missing because any building left partially assembled may be seriously damaged by light winds. Call 1-800-851-1085 or [email protected]

•Never concentrate your total weight on the roof of the building. When using a step ladder make sure that it is fully open and on even ground before climbing on it.

•Do not attempt to assemble the building on a windy day, because the large panels acting as a

"sail", can be whipped about by the wind making construction difficult and unsafe.

CARE & MAINTENANCE....

A5 Web

Finish: For long lasting finish, periodically clean and wax the exterior surface. Touchup scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per manufacturer's recommendation.

Roof: Keep roof clear of leaves and snow with long handled, soft-bristled broom. Heavy amounts of snow on roof can damage building making it unsafe to enter. In snow country,

Roof Strengthening Kits are available for most Arrow Buildings for added protection against heavy snow accumulation.

Doors: Always keep the door tracks clear of dirt and other debris that prevent them from sliding easily. Lubricate door track annually with furniture polish or silicone spray. Keep doors closed and locked to prevent wind damage.

Fasteners: Use all washers supplied to protect against weather infiltration and to protect the metal from being scratched by screws. Regularly check your building for loose screws, bolts, nuts, etc. and retighten them as necessary.

Moisture: A plastic sheet (vapor barrier) placed under the entire floor area with good ventilation will reduce condensation.

Other Tips....

• Wash off inked part numbers on coated panels with soap and water.

• Silicone caulking may be used for watertight seals throughout the building.

Do not store swimming pool chemicals in your building. Combustibles and corrosives must be stored in air tight approved containers.

Keep this Owner's Manual and Assembly Instructions for future reference.

ACCESSORIES....

A6 WEB

ROOF STRENGTHENING

(heavy snow load) KITS

Extra roof beams and gable braces designed for added protection against heavy snow accumulation. Increases the strength of your roof by 50%.

ANCHOR KITS

Model No. AK4

Anchor Kit contains heavy-duty steel augers, 60' (18 m) of steel cable and

4 cable clamps. No digging or concrete pouring, just insert cable under roof, over roof beams, into augers and twist augers into the ground. For buildings larger than 10'x9' (3,0 m x 2,6 m), use 2 kits.

Model No. AK100

New concrete anchor system permits anchoring any size Arrow building directly to a concrete slab. Each kit contains heavy-duty, hot-dipped galvanized steel corner gussets and perimeter clips which fit over the floor frame and lag bolt into a concrete slab.

Full assembly instructions and a 1/4" masonary drill bit are included.

Model No. AK600

Earth Anchor Kit anchors any size

Arrow building to the ground.

Each kit contains heavy duty, hot-dipped galvanized steel corner gussets and 4 earth anchors.

TOOL HANGING RACK

Model No. TH100

The perfect tool organizer. Twin

25 1/2" (64,8 cm) steel channels plus five heavy-duty snap-in hangers and a small tool holder for screwdrivers, pliers, etc. Holders slide along channel for fully adjustable spacing. Great for garage, basement, or the back of any door. Fits all Arrow storage buildings.

FLOOR FRAME KITS

MODELS FB47410, FB5465, FB106-A

FB109-A and FB1014-A

A simple new floor frame system made of heavy-duty, hot-dipped galvanized steel. Use as base for plywood, sand or stone.

ATTIC KIT / WORKBENCH KIT

Model No. AT101

Heavy-duty galvanized steel bars that fit all 10' (3,0 m) wide Arrow buildings.

They install quickly and easily to help organize space and create more useable space as an attic or workbench. Will hold up to 250 lbs.

(113 kg) evenly distributed.

Some drilling required to fit buildings without mid-wall bracing.

SHELF UNITS

Heavy-duty, galvanized steel shelf units help organize storage space. They easily mount on the wall or sit on the floor. Fits all

Arrow buildings.*

Model No. SS404

• Makes 8" to 12" (20,3-30,5 cm)

wide shelves in any length.

• Brackets, braces,

hardware included.

Lumber is not included.

Model No. SS900-A

• Grey color

• 3 shelves

• Holds up to 85 lbs. (38 kg)

(even weight distribution)

* Some drilling required to fit buildings without mid-wall bracing.

THIS

PAGE

WAS

LEFT

BLANK

INTENTIONALLY

7

8

THIS

PAGE

WAS

LEFT

BLANK

INTENTIONALLY

Anchoring

BE09

Anchoring Down The Building

It is important that the entire floor frame be anchored after the building is erected.

Below are recommended ways of anchoring.

Anchoring into Wood/Post:

Use 1/4" (6 mm) Wood Screws. There are 1/4" (6 mm) dia. holes provided in the frames for proper anchoring.

1.

2.

Anchoring into Concrete:

1. For poured concrete slab or footing or patio blocks:

Use 1/4" x 2" (6 mm x 51 mm) Lag Screws.

2. For Anchor Post of Concrete poured after building is erected: Use 1/4" x 6" (6 mm x 152 mm) Lag Screws.

1.

2.

9

QR10

27

28

29

30

23

24

25

26

19

20

21

22

15

16

17

18

Assembly

Key No.

1

2

3

4

5

6

11

12

13

14

7

8

9

10

35

36

37

38

31

32

33

34

39

40

10

9947

9945

9889

9890

9891

9892

9893

9940

9879

9880

9881

9927

9883

9884

9885

10184

9941

10183

9897

9898

9899

10200

9905

10176

67734

9944

9871

9872

9873

9874

9875

9876

9877

9878

Part

Number

10202

9866

10201

9868

10199

9870

Parts List

Part

Description

Side Floor Frame

Outer Front Floor Frame

Center Front Floor Frame

Rear Floor Frame

Floor Brace

Right Front Corner Panel

Quantity Check

in Carton List

2

2

2

1

1

2

Left Front Corner Panel

Right Rear Corner Panel

Left Rear Corner Panel

Wall Panel

Front Wall Panel

Wall Panel

Wall Panel

Right Roof Panel

Left Roof Panel

Roof Panel

Roof Panel

Rear Wall Channel

Rear Wall Angle

Shelf

Roof Beam

Main Door Header

1

1

1

2

2

2

1

1

1

2

1

2

2

4

2

1

Outer Door Header

Main Header

Outer Header

Right Gable

Left Gable

Right Door Jamb

Left Door Jamb

Right Door

Left Door

Door Latch Brace

Tool Bar

Right Roof Trim

Left Roof Trim

Floor Channel

Door Brace

Astragal

Foam Board

Vertical Door Brace

4

1

2

4

2

2

1

2

1

1

1

1

1

1

1

1

1

1

QR11

Assembly by Key No.

11

Hardware

QR12

65103

#8-32 Hex Nut (108)

65941

#6-32 Hex Nut (24)

(Packed with Screws)

65923

#8-32x3/8" (10 mm)

Bolt (108)

65004

#8Ax5/16" (8 mm)

Screw (242)

66714

#6-32x7/16" (11 mm)

Flat Hd Bolt (24)

(Packed with Screws)

65958

#8-32x7/8" (22 mm)

Bolt (2)

(Packed with Screws)

66684

Spring Latch (2)

66646

Washer (257)

(7 sheets of 40)

67468

Peak Cap (1)

66054

Latch - Attic Door (1)

66609

Hinge (4)

66183

Roof Trim Cap

(2 right & 2 left)

66148

Cap Protector (14)

67236

Adhesive Pad (2)

12

66043

Locking Handle (1)

66149

Tool Hook (5)

66150

Screw Driver Holder (1)

66082

Corner Cap (2)

Step 1

BE13

The front floor frame is made up of three pieces. The rear floor frame is made up of two pieces. The holes in these pieces will align when the pieces are positioned with correct amount of overlap. The illustrations below show the proper overall length for the rear and front. Proceed as follows:

1

Place the outer front floor frames as shown. Position the center front

floor frame on top of the two outer front floor frames. Join the frames by inserting six bolts and nuts.

2

Overlap the rear floor frames as shown. The holes in these pieces will align when the pieces are positioned with correct amount of overlap. See the illustrations below for the proper overall length of the rear floor frame. Join the frames by inserting three bolts and nuts as shown.

3

Double check the length of each.

● Parts Needed For ●

Floor Frame Assemblies

●

●

●

9866

9868

STEP

2

10201

STEP

1

Front Floor Frame 95 1/4" 241,9 cm

9866

Rear Floor Frame 95 1/4"

241,9 cm

9868

STEP

3

95 1/4" 241,9 cm Rear

95 1/4" 241,9 cm Front

13

Step 2

BE14

● Parts Needed For ●

Floor Frame

1

Place the floor frame pieces that you assembled on the ground. Assemble the four corners of the floor frame using two screws at each corner as shown.

2

Measure the floor frame diagonally. When the diagonal measurements are equal, the floor frame is square.

The floor frame must be square

and level or holes will not align.

10202

●

●

●

9868

10202

Rear Floor Assembly

STEP

1

FRONT

Front Floor Assembly

10202

When Diagonal Measurements are Equal the Floor Frame is Square

FRONT

STEP

2

14

Step 3

BE15

● Parts Needed For ●

Floor Frame Kit

1

Snap channels 10200 together as shown. Join the channels by inserting four nuts and bolts. Make two complete assemblies.

FRONT

15

16

Step 4

BE16

● Parts Needed For ●

Attaching Floor

Frame Kit

1

Do not attach decking material at this time!

NOTE: FLOOR FRAME MUST BE LEVEL AND

SQUARE BEFORE PROCEEDING!

2

Check floor frame for slots.

3

Bend tabs and assemble parts.

4

Overlap slots on 10199 and attach to front floor frame using eight screws.

●

●

●

STEP

3

STEP

4 factory slot

STEP

2

Bend Tabs

Install

10199 FRONT 10199

FRAME MUST BE SQUARE

AND LEVEL

Step 5

BE17

Finishing Material

Select one of the suggested finishing materials. Be sure Floor Frame Kit lies flat on the ground. To prepare the earth bed, remove sod and other organic debris, level the high spots with a flat shovel, and tamp the bed down.

LAY EXTERIOR PLYWOOD OR ANY SUITABLE DECK MATERIAL (5/8" 15,5 mm MINIMUM THICK-

NESS)

NOTE: Pressure Treated Lumber must not be used where it will make contact with your storage building.

The properties of Pressure Treated Lumber will cause accelerated corrosion. If Pressure Treated

Lumber comes in contact with your storage building your warranty will be voided.

IMPORTANT NOTE: If leveling blocks are required due to uneven ground conditions, the floor frame kit must be completely supported, because the kit is not self supporting. Plywood rests on top of the floor frame.

Step 6 Placement & Amount of Material

94"

238,8 cm

CORRECT

INCORRECT

32 5/8"

82,9 cm

Drill and fasten wood to steel frames using dry wall screws

NOTE: ALIGN EDGE

OF PLYWOOD WITH

SIDE AND REAR

FLOOR FRAMES.

FRONT

1-4x8 1220x2440 mm SHEET

DECK MATERIAL

SUGGESTION: Use remaining decking material for shelving or entry ramp.

FRAME MUST BE SQUARE AND LEVEL

BEFORE ATTACHING PLYWOOD.

17

Step 7

QR18

● Parts Needed For ●

Header/Door Header

Assembly

●

●

●

●

●

●

●

The header assembly is made up of two pieces. The door header assembly is made up of two pieces. The illustrations below show the proper overall length for the header/door header assembly. Proceed as follows:

1

Place the outer header as shown.

Snap the main header over the outer header. See the illustration for the proper overall length of the header assembly.

2

Place the outer door header as shown. Snap the main door header over the outer door header. See the illustration for the proper overall length of the door header assembly.

3

Double check the length of each.

The header/door header combo reinforces the front wall and roof. It is made up of two assemblies.

4

Positioning the door header as shown, attach the header to the door header using 13 screws along entire length. Set this piece aside for later use.

Header Assembly

Door Header Assembly

9947

END VIEW

Header Assembly

Door Header Assembly

9945

95 13/16"

243,4 cm

10184

Header Assembly

92 3/4"

235,6 cm

9889

Door Header Assembly

STEP

1

STEP

2

STEP

3

STEP

4

18

Step 8

BE19

The main frame pieces reinforce the walls and roof. These pieces will later be installed in the center of the roof and at the top edge of the rear wall.

Proceed as follows:

1

Overlap the roof beam pieces as shown in the figure (large hole on top) and fasten the two pieces together with four bolts and nuts where shown.

2

Overlap the rear wall angle pieces as shown in the figure and fasten them together with four bolts and nuts where shown.

3

Set the assemblies aside. You will use them later.

● Parts Needed For ●

Roof Beam/Rear

Wall Angle Assembly

9885

●

●

STEP

1

Roof Beam Assembly

9883

95 7/8"

243,5 cm

STEP

2

Rear Wall Angle Assembly

9883

9885

19

20

Step 9

QR20

The steps on this page tell how to assemble the right door. Proceed as follows:

1

Position hinges on side of right

door panel as shown and fasten with

7/16" (11 mm) flat head bolts outside and #6 hex nuts inside.

2

Slip foam board under lip of door, away from hinges, foil facing outward. See caution. Hold the vertical

door brace against the long edge of the foam board inside the door and fasten to door using five bolts and nuts.

3

Position astragal to door, as shown, and fasten to side of door using six screws.

● Parts Needed For ●

Right Door Assembly

10176

STEP

3

10176

9905

●

●

●

●

●

●

Foam Board (1)

● 9944 Vertical Door Brace (1)

67734

9940

67734

9944

Hinge

STEP

1

9940

CAUTION:

SHARP EDGE

Hinge

Flat Head Bolt

7/16" (11 mm)

9944 Screw

9905

Foil Side

STEP

2

STEP

4

4

Cover ends of door panel with

door braces. Edge of door panel slides into brace. Fasten braces to door using two screws on each brace.

5

Fasten door latch brace to door and astragal using four screws. Using an awl, ice pick or nail, push holes through foam board at the handle holes. Attach locking handle to door using 7/8" (22 mm) bolts.

6

Attach latch by inserting onto square shaft of handle.

7

Set the door aside for later use.

Screw

10183

STEP

5

STEP

6

Step 10

QR21

The steps on this page tell how to assemble the left door. Proceed as follows:

1

Position hinges on side of left

door panel as shown and fasten with

7/16" (11 mm) flat head bolts outside and #6 hex nuts inside.

2

Slip foam board under lip of door, away from hinges, foil facing outward. Hold the vertical door brace against the long edge of the foam board inside the door and fasten to door using five bolts and nuts.

3

Cover ends of door panel with

door braces. Edge of door panel slides into brace. Fasten braces to hinged side of door using one screw on each brace.

4

Attach spring latches to door braces and door using three screws on each latch.

5

Set the door aside for later use.

9905

● Parts Needed For ●

Left Door Assembly

Door

(Top)

STEP

4

9944

Door

(Bottom)

●

●

● ●

●

●

END VIEW

STEP

2

67734

9941

Screw

STEP

1

9941

Hinge

67734

7/16" (11 mm)

Flat Head

Screw Hinge

9944

Foil Side

9905

STEP

3

21

Step 11

BE22

NOTE

The remainder of the building assembly requires many hours. Do not continue beyond this point if you do not have enough time to complete the assembly today. A partially assembled building can be severely damaged by light winds.

Each screw and bolt in the wall requires a washer.

● Parts Needed For ●

Corners/Gables

STEP

2

REAR

●

●

●

●

●

●

●

Wide Side

STEP

3

SIDE

CORRECT INCORRECT

1

Position right & left front corner

panels at the corners of the floor frame as shown. The widest part of each corner panel must be placed along the front of the building. Fasten the corner panels to the floor frame with four screws, where shown.

Support the corner panel with a step ladder until next panel is fastened.

2

Attach the right & left rear corner

panels to the rear corners, as shown.

NOTE

Be careful to install the correct panel in each position as shown

3

Fasten wall panels 9874 to the sides of building using four screws into side floor frame. The crimped rib should go under the rib of adjacent panel. Fasten overlapping rib using two screws and a bolt with nut.

4

Fasten the right & left gables across the top of the side panels using five screws on each gable.

5

Double-check the part numbers of the wall panels, before proceeding.

22

9871

STEP

1

9891

9874

TOP VIEW

FRONT

9872

Attach panels with extra holes facing up.

Washer

STEP

4 9890

9873

Panels rest on frame as shown

Crimped Rib

Underneath

9870

Narrow

Side

SIDE

9874

The floor frame must be square

and level or holes will not align.

Step 12

BE23

The main frame pieces give rigidity to the front and rear walls.

1

Fasten the rear wall angle as-

sembly across the top of the rear wall using eight screws.

2

Fasten the header/door header

assembly across the top of the front walls using six screws, where shown.

3

Join gables to header in the front corners, using a bolt and nut.

STEP

3

● Parts Needed For ●

Frames

●

●

STEP

1

Rear Wall Angle Assembly

Header/Door Header Assembly

STEP

2

23

Step 13

BE24

Each wall panel has a crimped rib on one side. The crimped rib should go under the rib of the adjacent panel that follows it.

1

Fasten all the wall panels at the top and bottom with screws. Attach panels with extra holes facing up.

2

Fasten overlapping ribs using two screws and a bolt with nut.

● Parts Needed For ●

Wall Panels

STEP

1

9877

9876

●

●

●

Be sure that you have the correct panel in each position. Do this by overlapping the panels and determining if the holes line up with the holes in the frame.

9876

24

9875

Panels rest on frame as shown

STEP

2

9875

Crimped Rib

Underneath

Step 14

BE25

The door jambs reinforce the door opening and provide an attractive trim. Follow these steps for both door jambs.

1

Fasten a right door jamb to the front wall panel with three bolts and nuts as shown.

2

Fasten the top of the door jamb to the door header with two screws. Do the same for the bottom into frame.

Repeat steps 1 through 2 for the opposite left door jamb.

● Parts Needed For ●

Door Jambs

●

●

Screw

TOP VIEW

Door Header

Screw

TOP VIEW

Door Header

Bolt STEP

2

9893

9892

STEP

1

25

26

Step 15

BE26

1

Bend tab at each end of roof beam

assembly upward. Position beam across width of building, down on the ledge of gables at center hole location, but do not fasten at this time.

● Parts Needed For ●

Roof Beam

STEP

1

Roof Beam Assembly

Step 16

BE27

● Parts Needed For ●

Right/Left Roof Panels

●

●

Installing the roof panels is best done with a step ladder. Begin installing roof panels at the right side of the building. Each screw and bolt in the roof requires a washer.

Note: Tab of roof beam is fastened between roof panel and gable using the center hole.

NOTE

Measure the building diagonally again and make adjustments to make sure the building is square and level. This will make the roof panels fit better, and holes will align.

3

Install the left roof panel 9879 on the left side in the position shown below.

Screws To

Rear Wall

Angle

Fasten At

Overlap With

Bolt (Later)

Bolts To

Gable

1

Locate the roof panels and find the

right roof panel part number 9878.

2

Position a right roof panel at the right side and fasten to the gable, header and roof beam and rear wall angle using screws and bolts with nuts as shown.

9879 Left Roof Panel

STEP

3

Screws To

Roof Beam

Screws To

Header

Nut

Washer

Roof Beam

Bolt

STEP

2

9878 Right Roof Panel

FRONT

27

28

Step 17

BE28

● Parts Needed For ●

Roof Panels

1

Install a wide roof panel 9880, narrow roof panel 9881, and a wide

roof panel 9880 in the positions shown. Fasten middle of rib overlap with a bolt and nut.

Note:

Narrow roof panel crimped rib is overlapped by wide rib of adjacent panel where possible

STEP

1

9880 Roof Panel

9881 Roof Panel

●

●

9880 Roof Panel

FRONT

Step 18

BE29

● Parts Needed For ●

Roof Trim

●

●

1

Overlap the right & left roof trim pieces as shown in the figure and fasten them together with one screw.

Make two assemblies.

2

Attach the roof trim assemblies to the ends of the roof panels on the front and rear of the building using screws at each roof panel overlap.

4

Fasten the roof trim caps to the roof trim using a screw.

5

Fasten the roof trim and peak cap together using bolts and nuts.

6

Fasten the corner caps to the ends of the header, using adhesive pads.

3

Using your thumb and index finger, overbend the bottom flange of the roof trim at the corner inward enough so the right and left roof trim

caps fit onto right and left corners.

9899 Left Roof Trim

STEP

4 Roof Trim Cap

98 1/8"

249,2 cm

STEP

2

Roof Trim Assembly

STEP

1

9898 Right Roof Trim

Adhesive Pad

STEP

6

STEP

3

Peak Cap

STEP

5

Tuck Flange

Inward to Fit

Inside of

Roof Trim Cap

Corner Cap

29

30

Step 19

BE30

● Parts Needed For ●

Shelving/Channel/Tool Bar

1

Overlap the rear wall channel pieces as shown in the figure to the correct overall dimension.

2

Fasten the rear wall channel as-

sembly across the middle of the rear wall using 13 screws.

3

Position a shelf inside rear wall channel and slide to the end of building. Fasten using ten bolts and nuts through panels.

Repeat Step 3 for the opposite shelf.

4

Install remaining two shelves above the first two at the holes provided, using ten bolts and nuts.

5

Fasten the tool bar across the upper rear wall using eleven screws from the outside.

●

●

●

Screw Driver Holder(1)

Tool Hook (5)

Tool Hooks slide along track to any desired position.

Keeps rakes, shovels, brooms and much more in a safe and accessible location.

The Screw Driver Holder is engineered for all types of hand tools such as screwdrivers and pliers. A total of seven hand tools may be stored.

9927

STEP

1

77 5/8"

197,2 cm

Rear Wall Channel Assembly

STEP

5

9897

Cap Protector

Install Cap Protectors to the ends of the Tool Hooks and Screw Driver Holder.

9927

STEP

4

9884

9884

Rear Wall

Channel Assembly

STEP

2

9884

9884

STEP

3

Step 20

QR31

1

Position doors in corners of door opening as shown and fasten hinges to jambs with 7/16" (11 mm) flat hd bolts and #6 hex nuts.

2

Close doors. Adjust so that latch engages behind left door, then tighten set screw. The unit is locked. Turn key and remove.

● Parts Needed For ●

Installing Door

Congratulations, you have completed assembly of your storage building.

●

●

Set Screw

STEP

2

STEP

1

Keep this Owner's Manual and Assembly Instructions for future reference.

31

GS83-C

RE32

ANCHORING

Anchor your building at this time.

VGS83-B 697.68600

SOME FACTS ABOUT RUST

Rusting is a natural oxidizing process that occurs when bare metal is exposed to moisture. Problem areas include screw holes, unfinished edges, or where scrapes and nicks occur in the protective coating through normal assembly, handling and use. Identifying these natural rusting problem areas and taking some simple rust protection precautions can help to stop rust from developing, or stop it quickly as soon as it appears.

1. Avoid nicking or scraping the coating surface, inside and out.

2. Use all the washers supplied. In addition to protecting against weather infiltration, the washers protect the metal from being scraped by the screws.

3. Keep roof, base perimeter and door tracks free of debris and leaves which may accumulate and retain moisture. These can do double damage since they give off acid as they decay.

4. Touch up scrapes or nicks and any area of visible rust as soon as possible. Make sure the surface is free of moisture, oils, dirt or grime and then apply an even film of high quality touch-up paint.

712010111