Zebra WORKABOUT Owner Manual

Psion Teklogix
WORKABOUT PRO HDK
User Manual
September 12 2007
ISO 9001 Certified
Quality Management System
Part No. 8100057.C
© Copyright 2007 by Psion Teklogix Inc., Mississauga, Ontario
This document and the information it contains is the property of Psion Teklogix Inc., is issued in
strict confidence, and is not to be reproduced or copied, in whole or in part, except for the sole
purpose of promoting the sale of Psion Teklogix manufactured goods and services. Furthermore,
this document is not to be used as a basis for design, manufacture, or sub-contract, or in any
manner detrimental to the interests of Psion Teklogix Inc.
Windows® and the Windows Logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
and any use of such trademarks by Psion Teklogix Inc. is under license.
All trademarks are the property of their respective holders.
Return-To-Factory Warranty
Psion Teklogix Inc. provides a return to factory warranty on this product for a period of twelve
(12) months in accordance with the Statement of Limited Warranty and Limitation of Liability
provided at www.psionteklogix.com/warranty. (If you are not already a member of Teknet and you
attempt to view this warranty, you will be asked to register. As a member of Teknet, you will have
access to helpful information about your Psion Teklogix products at no charge to you.) In some regions, this warranty may exceed this period. Please contact your local Psion Teklogix office for
details. For a list of offices, see Appendix A: “Support Services / Worldwide Offices”. The warranty on Psion Teklogix manufactured equipment does not extend to any product that has been
tampered with, altered, or repaired by any person other than an employee of an authorized Psion
Teklogix service organization. See Psion Teklogix terms and conditions of sale for full details.
Warning: Psion Teklogix warranties take effect on the date of shipment.
Service
Psion Teklogix provides a complete range of product support services to its customers. For detailed information, please refer to Appendix A: “Support Services / Worldwide Offices”. This
section also provides information about accessing support services through the Psion Teklogix
web site.
Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC
This Product, and its accessories, comply with the requirements of the Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC. If your end-of-life Psion Teklogix product or
accessory carries a label as shown here, please contact your local country representative for details
on how to arrange recycling.
For a list of international subsidiaries, please go to:
www.psionteklogix.com/EnvironmentalCompliance
Restriction On Hazardous Substances (RoHS) Directive 2002/95/EC
What is RoHS?
The European Union has mandated that high environmental standards be met in the design and
manufacture of electronic and electrical products sold in Europe, to reduce hazardous substances
from entering the environment. The “Restriction on Hazardous Substances Directive (RoHS)” prescribes the maximum trace levels of lead, cadmium, mercury, hexavalent chromium, and flame
retardants PBB and PBDE that may be contained in a product. Only products meeting these high
environmental standards may be “placed on the market” in EU member states after July 1, 2006.
RoHS Logo
Although there is no legal requirement to mark RoHS-compliant products, Psion Teklogix Inc. indicates its compliance with the directive as follows:
The RoHS logo located either on the back of the product or underneath the battery in the battery
compartment (or on a related accessory such as the charger or docking station) signifies that the
product is RoHS-compliant as per the EU directive. Other than as noted below, a Psion Teklogix
product that does not have an accompanying RoHS logo signifies that it was placed on the EU
market prior to July 1, 2006, and is thereby exempt from the directive.
Note: Not all accessories or peripherals will have a RoHS logo due to physical space limitations
or as a result of their exempt status.
Disclaimer
Every effort has been made to make this material complete, accurate, and up-to-date. In addition,
changes are periodically added to the information herein; these changes will be incorporated into
new editions of the publication.
Psion Teklogix Inc. reserves the right to make improvements and/or changes in the product(s)
and/or the program(s) described in this document without notice, and shall not be responsible for
any damages, including but not limited to consequential damages, caused by reliance on the material presented, including but not limited to typographical errors.
TABLE OF CONTENTS
Chapter 1: Introduction
1.1
1.2
1.3
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Text Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Contents Of The HDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.3.1 Files In The HDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.4
1.5
1.6
Obtaining The HDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
About the WORKABOUT PRO Hand-Held Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Discontinued Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Chapter 2: Hardware
2.1
2.2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Variants Of The WORKABOUT PRO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2.2.1 Scanner Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2.2 Expansion Card Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.3
WORKABOUT PRO C, S, M, ME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2.3.1 Main Processor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.3.2 Peripheral Processors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.4
WORKABOUT PRO 2nd. Generation C, S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4.1 Main Processor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4.2 Peripheral Processors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5
2.6
2.7
2.8
Identifying Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.8.1 Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
15
15
16
2.9 Switching The Backup Battery Power On And Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.10 Connector Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 3: Software
3.1
3.2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windows Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1 The Peripheral Control (PCO) Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2 The PCMCIA Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3 The Serial Port Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3
Non-Psion Teklogix Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.3.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.3.2 Drivers In Windows Mobile 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.4
3.5
System Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Registry Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.1 Registry Settings For Controlling VGA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.2 Registry Settings For Serial Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.3 Registry Settings For Psion Teklogix Device Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.4 Registry Settings For Non-Psion Teklogix Device Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.4.1 Loading Non-Psion Teklogix Device Drivers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Psion Teklogix WORKABOUT PRO HDK User Manual
21
21
21
21
21
22
22
22
22
23
23
24
i
Contents
3.6
3.7
COM Port Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
The C++ Application Programming Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.7.1 Installing The Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.7.2 Development Platforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.7.3 The Interrupts Namespace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.7.4 The ExpansionWakeup Namespace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.7.5 The GPIO Namespace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.7.6 The EEPROM Namespace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.7.7 The ExpansionUSB Namespace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.7.8 The USBhub Namespace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.7.9 The ScannerPort Namespace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.7.10 The smBus Namespace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.7.11 The PCMCIA Namespace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Chapter 4: Mechanical Considerations
4.1
4.2
4.3
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
HDK Mechanical Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.3.1 Endcap-Mounted Device Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.3.2 Backplate-Mounted Device Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.3.3 Expansion Module Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.4
Location And Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.4.1 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.4.2 Backplate-Mounted Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.4.3 Expansion Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.4.3.1 100-Pin Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.4.3.2 Mounting Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.4.4 Endcap, Card Stop, And Stylus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.4.5 Bottom Footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Chapter 5: External Connectors
ii
5.1
5.2
Overview Of External Connectors, Cables, And Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
External Connectors On The WORKABOUT PRO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
5.2.1 WORKABOUT PRO C, S, M, ME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
5.2.2 WORKABOUT PRO 2nd. Generation C, S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.3
The LIF Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
5.3.1 Sensing Device Presence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
5.4
The Tether Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
5.4.1 The WORKABOUT PRO C, S, M, ME Tether Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
5.4.1.1 COM2: Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5.4.1.2 Sensing Device Presence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
5.4.2 The WORKABOUT PRO 2nd. Generation C, S Tether Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
5.4.2.1 Sensing Device Presence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5.4.3 Cables For the Tether Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5.5
5.6
The WORKABOUT PRO C, S, M, ME Audio Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Docking Stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.6.1 Single Unit Docking Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.6.1.1 The USB Host Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.6.1.2 The USB Client Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.6.2 Four Unit Multi-Dock Docking Station (Quad Docker) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Psion Teklogix WORKABOUT PRO HDK User Manual
Contents
5.7
Vehicle Cradles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
5.7.1 The Vehicle Cradle 15-Pin Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
5.8
Port Replicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
5.8.1 The Serial Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
5.9 Other Cables And Adaptors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
5.10 Mechanical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Chapter 6: Internal Connectors
6.1
6.2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
WORKABOUT PRO 2nd. Generation C, S Audio Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
6.2.1 Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
6.3
WORKABOUT PRO 2nd. Generation C, S USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
6.3.1 Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
6.4
6.5
100-Pin Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Scanner Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Chapter 7: 100-Pin Connector
7.1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1.1 Signals On The 100-Pin Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1.2 Connector Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1.3 Connector Position And Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
63
63
63
64
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
7.11
100-Pin Connector Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power And Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data And Address Buses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General-Purpose I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General-Purpose Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCMCIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wakeup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I2C Device Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.11.1 I2C Addresses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.11.2 Expansion Module EEPROM Fields. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
64
69
70
70
71
71
72
72
73
73
74
75
7.12 Example Expansion Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
7.13 Psion Teklogix Serial Endcaps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
7.13.1 Serial Port Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
7.14 WORKABOUT PRO 2nd. Generation C, S USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Chapter 8: Scanner Connector
8.1
8.2
8.3
8.4
8.5
8.6
8.7
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scanner Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scanner Connector Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scanner Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Scanner Flex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power And Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signals To The Scanner Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Psion Teklogix WORKABOUT PRO HDK User Manual
81
82
83
83
85
85
86
iii
Contents
Chapter 9: Example: Scanner Converter Board
9.1
9.2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Example Scanner Boards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
9.2.1 Serial Scanner Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
9.3
9.4
Power And Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Signals To The Scanner Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
9.4.1 Serial Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
9.4.2 USB Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
9.4.3 Control Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Chapter 10: Example: PCMCIA Expansion Module
10.1
10.2
10.3
10.4
10.5
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Expansion Module Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
10.5.1 PCMCIA Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
10.5.2 The Card Detect Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
10.5.3 The Buffer Enable Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
10.5.4 The Slot Power Enable Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
10.5.5 Selectable Card Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
10.6 EEPROM Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Chapter 11: Example: Multi-I/O Expansion Module
11.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
11.2 Schematics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
11.3 Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
11.3.1 Main Logic Board 100-Pin Connector (J1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
11.3.2 Main Logic Board Scanner Connector (J2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
11.3.3 Scanner-Port Serial Connector (J3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
11.3.4 USB Host Port 2 Connector (J4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
11.3.5 The FF UART Serial Connector (J5). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
11.3.6 The USB Host 1 Connector (J6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
11.3.7 The Power Connector (J7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
11.4 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
11.4.1 Slot Power Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
11.4.2 EEPROM Write Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
11.4.3 Voltage Configuration For Standard-Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
11.4.4 Voltage Configuration For High-Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
11.4.5 Control Signals For FFUART Level Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
11.4.6 TTL Output Option For Scanner Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
11.5 Power And Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
11.6 EEPROM Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
11.7 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
iv
Psion Teklogix WORKABOUT PRO HDK User Manual
Contents
Appendices
Appendix A: Support Services / Worldwide Offices
A.1
A.2
A.3
Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Product Repairs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Worldwide Offices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
A.3.1 Company Headquarters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
A.3.2 Canadian Service Centre . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
A.3.3 North American Headquarters And U.S. Service Centre . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
A.3.4 International Subsidiaries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
Appendix B: Resources
B.1
B.2
B.3
B.4
Psion Teklogix WORKABOUT PRO User Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Other Psion Teklogix Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Psion Teklogix Downloadable Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Psion Teklogix Accessory And Parts Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Appendix C: Specifications WORKABOUT PRO M
C.1
C.2
C.3
C.4
Hand-Held Computer Specifications WORKABOUT PRO M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3
Radio Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4
Scanner Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
Battery Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
C.4.1 Standard Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
C.4.2 High-Capacity Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6
Appendix D: Specifications WORKABOUT PRO C, S & ME
D.1
D.2
D.3
D.4
D.5
D.6
D.7
D.8
Hand-Held Computer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-3
D.1.1 Model Variants. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-3
WORKABOUT PRO C Variant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-3
WORKABOUT PRO S Variant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-4
WORKABOUT PRO ME Variant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-4
WORKABOUT PRO C, S, and ME Variants. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-5
Radio Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-7
Scanner Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-7
Battery Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-7
Appendix E: WORKABOUT PRO 2nd. Generation
E.1
E.2
E.3
E.4
WORKABOUT PRO Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E.1.1 WORKABOUT PRO C Variant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E.1.2 WORKABOUT PRO S Variant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E.1.3 WORKABOUT PRO All Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scanner Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E.4.1 Scanner/Imager Model Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E-3
E-3
E-3
E-3
E-8
E-8
E-8
E-8
Appendix F: Specifications WORKABOUT PRO Radios
F.1
F.2
F.3
Radio Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-3
802.11g Direct Sequence Spread Spectrum (Model RA2040) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-3
802.11b/g Direct Sequence Spread Spectrum (DSSS) (Model RA2041) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-3
Psion Teklogix WORKABOUT PRO HDK User Manual
v
Contents
F.4
F.5
GSM/GPRS/EDGE Radio (Model RA3030-G2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-4
Bluetooth Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-5
Appendix G: Specifications Scanners And Imagers
G.1
G.2
Scanner and Imager Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-3
Scanner Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-3
G.2.1 SE 1223HP, LR, ALR And SE 955HP Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-3
Imager Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-6
G.3.1 EV15 Imager Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-6
G.3.2 HHP5180 Imager Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-7
G.3.3 SX5393 Imager Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-8
G.3.4 SX5400 Imager Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G-10
G.3
Appendix H: Specifications WORKABOUT PRO Batteries
H.1
H.2
Battery Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-3
Standard Capacity–2000 mAh (Model WA3000-G1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-3
H.2.1 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-3
H.2.2 Standard Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-4
H.2.3 Environmental Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-5
High-Capacity 3000mAh (Model WA3006) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-6
H.3.1 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-6
H.3.2 Standard Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-7
H.3.3 Safety Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-8
H.3.4 Safety License. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-8
H.3.5 Environmental Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-8
Super High-Capacity (Model WA3010) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-9
H.4.1 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-9
H.4.2 Standard Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H-10
H.4.3 Safety Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H-11
H.4.4 Safety License. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H-12
H.4.5 Environmental Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H-12
Maxell ML2032 Rechargeable Coin Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H-13
WORKABOUT PRO 2nd. Generation (C And S) Internal Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H-13
H.3
H.4
H.5
H.6
Appendix I: Hardware Developer Kit License Agreement
I.1
I.2
I.3
I.4
I.5
I.6
I.7
I.8
I.9
I.10
HARDWARE DEVELOPER KIT LICENSE AGREEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-3
GRANT OF LICENSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-3
DESCRIPTION OF REQUIREMENTS, RESTRICTIONS, RIGHTS AND LIMITATIONS . . . . . . . . . . . . . . I-3
HIGH RISK ACTIVITIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-4
DISCLAIMER OF WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-4
LIMITATION OF LIABILITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-4
COPYRIGHTS, OWNERSHIP AND PROPRIETARY RIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-4
CONFIDENTIALITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-5
ENDING THIS AGREEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-5
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-5
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I
vi
Psion Teklogix WORKABOUT PRO HDK User Manual
1
INTRODUCTION
1.1 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Text Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Contents Of The HDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3.1 Files In The HDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4 Obtaining The HDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.5 About the WORKABOUT PRO Hand-Held Computer. . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.6 Discontinued Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Psion Teklogix WORKABOUT PRO HDK User Manual
1
Chapter 1: Introduction
About This Manual
1.1
About This Manual
This manual is supports developers of customized hardware for all variants of the Psion Teklogix
Inc. WORKABOUT PRO hand-held computer.
Chapter 1: Introduction
is an overview of the WORKABOUT PRO Hand-Held Computer and the
WORKABOUT PRO HDK.
Chapter 2: Hardware
describes, in general terms, the hardware of the WORKABOUT PRO.
Chapter 3: Software
gives an overview of the API for expansion devices, discusses installing
device drivers.
Chapter 5: External Connectors
describes the external connectors on the WORKABOUT PRO, and accessories that
connect to them.
Chapter 4: Mechanical Considerations
describes the space and mounting for expansion module devices.
Chapter 7: 100-Pin Connector
describes the electrical interface between the WORKABOUT PRO and expansion
module devices.
Chapter 8: Scanner Connector
describes the scanner connector.
Chapter 9: Example: Scanner Converter Board
describes the interface between the scanner and the standardized scanner connector.
Chapter 10: Example: PCMCIA Expansion Module
describes an example of an expansion module that has a PCMCIA slot.
Chapter 11: Example: Multi-I/O Expansion Module
describes an example of an expansion module that makes the serial and USB
connections on the 100-pin connector easily available.
Appendix A: Support Services / Worldwide Offices
provides the helpdesk phone number at Psion Teklogix Inc., Mississauga, Ontario,
Canada office and details the support services available. This appendix also lists
worldwide office addresses and their phone numbers.
Appendix B: Resources
contains a list of other publications and web sites where related information
is available.
Appendix C: Specifications WORKABOUT PRO M
contains specifications for the WORKABOUT PRO M variant.
Appendix D: Specifications WORKABOUT PRO C, S & ME
contains specifications for the WORKABOUT PRO C, S, and ME variants.
Appendix E: WORKABOUT PRO 2nd. Generation
contains specifications for the WORKABOUT PRO 2nd. Generation C and
S variants.
Psion Teklogix WORKABOUT PRO HDK User Manual
3
Chapter 1: Introduction
Text Conventions
Appendix F: Specifications WORKABOUT PRO Radios
contains specifications for the WORKABOUT PRO radios.
Appendix G: Specifications Scanners And Imagers
contains specifications for the WORKABOUT PRO internal scanners and imagers.
Appendix H: Specifications WORKABOUT PRO Batteries
contains specifications for the WORKABOUT PRO batteries.
Appendix I: Hardware Developer Kit License Agreement
provides the text of the License Agreement that accompanies the HDK.
1.2
Text Conventions
Note: Notes highlight additional helpful information.
Important: These statements provide important instructions or additional information that is
critical to the operation of the computer or other equipment.
Warning: These statements provide important information that may prevent injury, damage
to the equipment, or loss of data.
An arrow next to field description information (usually in tables) indicates a recommended or
suggested configuration setting.
1.3
Contents Of The HDK
The Hardware Development Kit (HDK) for the WORKABOUT PRO includes the
following items:
•
•
•
•
1.3.1
This manual.
Libraries and sample programs for the APIs for managing expansion cards and scanner
devices. See “The C++ Application Programming Interface” on page 25 for a description of
these files.
Drawings and engineering models of the backplates and endcaps available for the
WORKABOUT PRO. The models can be customized. See Chapter 4: “Mechanical Considerations” for a description of these models.
Sample schematics and drawings for expansion modules and scanner converter boards.
Files In The HDK
Table 1.1 Files in the HDK
Filename
4
Description
...\Mechanical\WORKABOUTPRO\G2\iges_files
\G2_C_body.igs
Body shell—WORKABOUT PRO 2nd.
Generation—C variant.
...\Mechanical\WORKABOUTPRO\G2\iges_files
\G2_mounting_frame.igs
Mounting frame—WORKABOUT PRO 2nd.
Generation C, and S variants.
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 1: Introduction
Files In The HDK
Table 1.1 Files in the HDK (Continued)
Filename
Description
...\Mechanical\WORKABOUTPRO\G2\iges_files
\G2_S_body.igs
Body shell—WORKABOUT PRO 2nd. Generation
S variant.
...\Mechanical\WORKABOUTPRO\iges_files
\backplate.igs
Backplate—all variants.
...\Mechanical\WORKABOUTPRO\iges_files
\colour_mono_terminal.igs
Body shell—WORKABOUT PRO C, M, and
ME variants.
...\Mechanical\WORKABOUTPRO\iges_files
\endcap.igs
Endcap—all variants.
...\Mechanical\WORKABOUTPRO\iges_files
\endcap_assembly.igs
Endcap assembly—all variants.
...\Mechanical\WORKABOUTPRO\iges_files
\mounting_frame.igs
Mounting frame—WORKABOUT PRO C, M,
ME. and S variants.
...\Mechanical\WORKABOUTPRO\iges_files
\pcmcia_xmod.igs
Sample expansion card—all variants.
...\Mechanical\WORKABOUTPRO\iges_files
\short_terminal.igs
Body shell—WORKABOUT PRO S variant.
...\Mechanical\WORKABOUTPRO\iges_files
\stylus_pen.igs
Stylus pen—all variants.
...\Mechanical\WORKABOUTPRO\pdf
\backplate.pdf
2D backplate—all variants.
...\Mechanical\WORKABOUTPRO\pdf
\endcap.pdf
2D endcap—all variants.
...\Mechanical\WORKABOUTPRO\pdf
\endcap_assembly.pdf
2D endcap assembly —all variants.
...\Mechanical\WORKABOUTPRO\pdf
\endcap_assembly_ball.pdf
2D ball for endcap—all variants.
...\Mechanical\WORKABOUTPRO\pdf
\endcap_assembly_ball_holder.pdf
2D endcap ball holder—all variants.
...\Mechanical\WORKABOUTPRO\pdf
\endcap_assembly_ball_spring.pdf
2D endcap, and ball spring—all variants.
...\Mechanical\WORKABOUTPRO\pdf
\endcap_assembly_stylus_rubber.pdf
2D stylus gasket for endcap—all variants.
...\Mechanical\WORKABOUTPRO\pdf
\housing_body.pdf MISSING
2D body shell—WORKABOUT PRO S variant.
...\Mechanical\WORKABOUTPRO\pdf
\internal_metal_frame.pdf
2D internal frame—WORKABOUT PRO C, M,
and ME variants.
...\Mechanical\WORKABOUTPR\G2\pdf
\mechanical_stop.pdf ADD TO LIBRARY
2D card stop—WORKABOUT PRO 2nd.
Generation C, and S variants.
...\Mechanical\WORKABOUTPRO\pdf
\stylus_pen.pdf
2D stylus—all variants.
Psion Teklogix WORKABOUT PRO HDK User Manual
5
Chapter 1: Introduction
Obtaining The HDK
Table 1.1 Files in the HDK (Continued)
Filename
1.4
Description
...\Electrical\WORKABOUTPRO\Samples
\PCMCIAExpansionCard.pdf
Sample schematic PCMCIA expansion
module—all variants.
...\Electrical\WORKABOUTPRO\Samples
\SerialScannerInterfaceBoard.pdf
Sample schematic scanner interface board for a
serial scanner—all variants.
...\Electrical\WORKABOUTPRO\Samples
\USBScannerInterfaceBoard.pdf
Sample schematic scanner interface board for a
USB scanner—all variants.
Obtaining The HDK
The HDK is available as a download from Psion Teklogix. If you have a Teknet usercode, the
download is available on the Teknet site at:
www.PsionTeklogix.com/downloads
1.5
About the WORKABOUT PRO Hand-Held Computer
The WORKABOUT PRO Hand-Held Computer is an industrial hand-held computer.
The following WORKABOUT PRO variants are available:
Model
WORKABOUT PRO
WORKABOUT PRO 2nd. Generation
Variant
Description
M
(discontinued)
Monochrome screen, full keyboard,
PXA255 processor.
C
Colour screen, full keyboard, PXA255 processor.
ME
Monochrome enhanced screen, full keyboard,
PXA255 processor.
S
Colour screen, short keyboard, PXA255 processor.
C
Colour screen, full keyboard, PXA270 processor.
S
Colour screen, short keyboard, PXA270 processor.
The specifications for these computers are in the following appendices:
• Appendix C: “Specifications WORKABOUT PRO M”
• Appendix D: “Specifications WORKABOUT PRO C, S & ME”
• Appendix E: “WORKABOUT PRO 2nd. Generation”
For details on the configuration and operation of the WORKABOUT PRO models consult the
user manuals listed in Appendix B: “Resources”.
6
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 1: Introduction
Discontinued Hardware
The following windows operating systems are available on the WORKABOUT PRO:
Yes
WORKABOUT PRO C
Yes
Yes
Yes
WORKABOUT PRO ME
Yes
Yes
Yes
WORKABOUT PRO S
Yes
Yes
Yes
WORKABOUT PRO
2nd. Generation
Yes
Windows Mobile 6
Windows CE .NET 4.2
Yes
Windows Mobile 5
Windows Mobile 2003
WORKABOUT PRO M
(discontinued)
Model
1.6
Windows Embedded CE 5.0
• Windows Mobile 2003
• Windows CE .NET 4.2
• Windows Embedded CE 5.0
• Windows Mobile 5
• Windows Mobile 6
Windows operating systems are available on the WORKABOUT PRO as follows:
Yes
Discontinued Hardware
The WORKABOUT PRO M and some of the peripherals described in this manual are no longer
available for purchase from Psion Teklogix. They are included in this manual for the benefit of developers who are continuing to support them alongside newer hardware. For currently available
hardware consult the Accessories Catalog at www.PsionTeklogix.com/Accessories.
Psion Teklogix WORKABOUT PRO HDK User Manual
7
2
HARDWARE
2.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2 Variants Of The WORKABOUT PRO . . .
2.2.1 Scanner Variants . . . . . . . . . .
2.2.2 Expansion Card Variants. . . . . .
2.3 WORKABOUT PRO C, S, M, ME . . . . .
2.3.1 Main Processor . . . . . . . . . .
2.3.2 Peripheral Processors . . . . . . .
2.4 WORKABOUT PRO 2nd. Generation C, S.
2.4.1 Main Processor . . . . . . . . . .
2.4.2 Peripheral Processors . . . . . . .
2.5 Identifying Hardware . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
11
11
11
11
11
12
13
13
13
15
2.6 The LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.7 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.8 Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.8.1 Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.9 Switching The Backup Battery Power On And Off . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.10 Connector Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Psion Teklogix WORKABOUT PRO HDK User Manual
9
Chapter 2: Hardware
Overview
2.1
Overview
This chapter gives an overview of the hardware of the WORKABOUT PRO.
2.2
Variants Of The WORKABOUT PRO
There are six variants of the WORKABOUT PRO. The specifications for all the variants are in the
following appendices:
• Appendix C: “Specifications WORKABOUT PRO M”
• Appendix D: “Specifications WORKABOUT PRO C, S & ME”
• Appendix E: “WORKABOUT PRO 2nd. Generation”
For the specifications of the radio, scanner, and battery options see:
• Appendix F: “Specifications WORKABOUT PRO Radios”
• Appendix G: “Specifications Scanners And Imagers”
• Appendix H: “Specifications WORKABOUT PRO Batteries”
For setup, configuration, and operational details consult the user manual for your WORKABOUT
PRO. A list of user manuals is included in Appendix B: “Resources”.
2.2.1
Scanner Variants
The WORKABOUT PRO comes standard with no scanner. Consult the specifications for the
scanners that are available for each WORKABOUT PRO variant.
The scanners and their housings fasten to the underside of the WORKABOUT PRO, replacing the
backplate. The scanner connects through a flex cable to the scanner connector on the
WORKABOUT PRO main logic board. The scanner may be installed by the end user; for instructions see Psion Teklogix WA9000, WA9005, & WA9006 Scanner Module Installation (Part number
8000030).
Only one internal scanner can be installed in a WORKABOUT PRO. The internal scanner can be
triggered from the trigger switch on the WORKABOUT PRO handgrip (if present), from one of
the [SCAN] buttons on the WORKABOUT PRO keyboard, or from an assigned keyboard key.
2.2.2
Expansion Card Variants
See the specifications for the WORKABOUT PRO variants for information on the expansion card
slots that are available. Additional card slots can be installed by connecting to the internal 100-pin
connector. Some card slots are accessed by removing the endcap.
2.3
WORKABOUT PRO C, S, M, ME
See Figure 2.1 on page 12.
2.3.1
Main Processor
The WORKABOUT PRO is built around a 400 MHz Marvell X-Scale PXA255 processor. This
processor can run binaries compiled for the ARMv4 and ARMv4i target processor.
Psion Teklogix WORKABOUT PRO HDK User Manual
11
Chapter 2: Hardware
Peripheral Processors
Figure 2.1 WORKABOUT PRO C, S, M, ME Block Diagram
802.11b/g radio
option
Main Logic Board (RMB)
PCMCIA Adaptor
(Option)
Internal 100-pin Expansion Slot
(Interfaces: I2C, SSP, Full Function UART,
USB host 1)
CompactFlash
CompactFlash Socket
Socket
Bluetooth
Antenna
PCMCIA card option
e.g. GSM/GPRS radio
3.3V
Address/Data
FF UART /
SSP /
PCMCIA Socket
Select /
USB_H1_PSW
SD Slot
Bluetooth
Module
3.3V
Keyboard Module (RKB)
CF
Power
Buffers
VIN
USB
DC_IN
Host 1
I2C
Display Module (RLB)
GSM
Connector
SD
Power
SW
BT Uart
Speaker
Connector
Audio/Touch
Controller
Microphone
Board-to-Board Connector (50-pin)
MIC in, SPK out
Speaker out
Touch controls
BT Power
SW
LCD data
Media
Processor
Keyboard
Status
LEDs
Connectors
Key Scan
VIN, 5V, 3.3V
AC-Link
Key Scan
Matrix
Backlight Control (PWM)
Message
LED
I2C
LED
driver
Scanbay Connector
UART
Scanbay
Power 5V
Backlight PWM
Battery Cover
SW
USB
Client
SPI
LED
Backlight
5V
Power MCU
USB Host 2 USB Host 1
Slide
SW
USB hub
controller
Charge
Status
Keyboard & Power
Management MCU
Backup
Battery
Charger
USB Host 3 USB Host 4
V+3.3, V+5,
V+CORE,..
etc.
Internal Scanner
Options:
- 1D Laser Scanner
- 2D Imager
- 1D Imager
Power
Enable
Key
IRQ
USB
Host Root
Tether LIF
Detect Detect
Rechargable Backup
Battery
VBAT
BAT_DATA
DC-DC Converter
Circuits
VIN
Audio/Touch
Controller
Diodes and
FETs
Charge Status
& Control
BT module /
PXA
LCD power
supplies
FLEX
Key Scan
Backlight
Power
Power
Switch
LCD TFT
(1/4 VGA
240x320)
3.3V
SDRAM
64 or 128 MB
PXA255 CPU
400MHz
EEPROM
RTC
4-wire Touch
Panel
FLASH
64MB
Address/Data
CS, etc
Backlight
LEDs
Speaker
3.3V
Main
Battery
Charger
Circuit
DC_IN
BT Uart
VBAT
BAT_DATA
Li-ion Battery
3.7V nominal
VBAT
50-pin Board-to-Board I/O Connector
50-pin Board-to-Board I/O Connector
Connector Board (RCB)
Battery Cover
Detect SW
BT TX/RX
DC_IN
USB Host 3 & Power
USB Host 4 & Power
USB Client
(From media processor)
Diodes
SERIAL
(TX/RX)
USB
Host
Tether
ID
Detect
DC
Input
Tether Connector
(18-pin)
2.3.2
DC
Input
Audio Jack
(headphone, mic)
USB
Client
USB
Host
LIF ID
Detect
LIF Connector
(12-pin)
Peripheral Processors
MSP430MF133 Keyboard Processor
The WORKABOUT PRO has a keyboard processor, for controlling and monitoring the keyboard
and signal LEDs, and the battery.
12
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 2: Hardware
WORKABOUT PRO 2nd. Generation C, S
MQ1188 Multimedia Platform Controller
This processor handles connections to the liquid-crystal display module and the SD/MMC card
slot. It also provides the USB host interface to the USB host (through the hub) and
client connections.
ISP1122A USB Host Hub
The ISP1122A USB hub, together with individual current limited load switches, provides USB
data lines and DC power to the USB ports on the following connectors:
• 100-pin expansion connector.
• Scanner connector.
• Tether connector.
• LIF connector.
The overcurrent sensing capability and DC power is not provided by the ISP1122A
controller alone.
This controller integrates a Serial Interface Engine (SIE), hub repeater, hub controller, USB data
transceivers, and a configurable number (2 - 5) of downstream ports. It has the following features:
•
•
•
•
Complies with USB Specification 1.1.
Full-speed (12Mbps) fully compliant.
OHCI register compliant.
Supports DMA.
WM9705 Audio Controller
The audio controller permits audio recording and playback to the AC97 specification. This chip
also handles the touchscreen digitizing input.
2.4
WORKABOUT PRO 2nd. Generation C, S
See Figure 2.2 on page 14.
2.4.1
Main Processor
The WORKABOUT PRO is built around a 520 MHz Marvell X-Scale PXA270 processor. This
processor can run binaries compiled for the ARMv4 and ARMv4i target processor.
2.4.2
Peripheral Processors
C8051F315 Keyboard Processor
The WORKABOUT PRO has a keyboard processor, for controlling and monitoring the keyboard
and signal LEDs, and the battery.
C8051F312 Microcontroller for Power Management Control
The C8051F312 controller is used for controlling and monitoring the power state of various components (e.g. Li-ion battery chargers) in the system. It also detects the presence of devices
connected to the LIF port and the tether port.
LC4128ZC CPLD
This CPLD is used for interfacing Compact Flash and PC cards via the internal 100-pin
expansion slot.
Psion Teklogix WORKABOUT PRO HDK User Manual
13
Chapter 2: Hardware
Peripheral Processors
Figure 2.2 WORKABOUT PRO 2nd. Generation C, S Block Diagram
802.11b/g radio
option
e.g. RA2041 radio
Main Logic Board (RMB)
PCMCIA Adaptor
(Option)
Internal 100-pin Expansion Slot
(Interfaces: I2C, SSP2, Full Function UART,
USB host 1)
CompactFlash
CompactFlash Socket
Socket
Bluetooth
Antenna
PCMCIA card option
e.g. GSM/GPRS radio
3.3V
Bluetooth
Module
Keyboard Module (RKB)
FF UART /
SSP2 /
PCMCIA
socket
Select /
USB_H1_PSW
CPLD
Headphone
Jack (J703)
USB DC_IN VIN
Host 1
GSM
Connector
I2C
Display Module (RLB)
Speaker
Connector
PCM
Audio/Touch
Controller
Touch controls
3.3V
SD Slot
AC97
BT Uart
LCD data
3.3V
Key
IRQ
Keyboard
Controller
Key
Scan
22-pin Flex Cable
SD Power
SW
V+3.3 /
VIN
GoForce 4000
Media Processor
BT Power
SW
VIN
Keyboard
Key Scan
Backlight
LEDs
FLEX
Key Scan
Scanbay Connector
Scanbay
Power
5V/3.3V
RTC
V+1.8MEM
V+CORE
Power I2C VCC_PLL
VCC_SRAM
VCC_BAT
USB
OTG
&
I2C
Control
Signals
Power MCU
(Regulated DC
outputs for CPU)
USB
Client
I2C
&
Control
Signals
Internal
USB
Connector
(CN601)
USB Power
USB Host 1
USB Host 2
Beeper Output
USB hub
controller
USB Host Root
Charge
Status
MCU for Power
Management Control
Tether LIF
Detect Detect
Backup
Battery
Charger
Li-Poly Backup
Battery
Slide
SW
5V
USB Host 3 USB Host 4
VIN
USB OTG
Transceiver
Charge
Status
System
Supplies
(e.g. 3.3V
and 5V)
Diodes
and FETs
Vbus
Power
SW
VIN
VBAT
BAT_DATA
USB OTG
& Power
Main
Battery
Charger
Circuit
DC_IN
BT module /
PXA
BT Uart
50-pin I/O Connector
50-wire Cable
50-pin I/O Connector
Connector Board (RCB)
Battery Cover Detect
Switch (To PXA270)
BT Uart
USB
Host 3
USB MCU
(USB / Serial
Interface)
Beeper
DC_IN
USB OTG & Power
USB Host 4 & Power
USB Client
(PXA270)
UART
Power Path
Selector
USB
OTG
Tether
ID
Detect
DC
Input
Tether Connector
(18-pin)
GoForce 4000 Media Processor
This provides the following:
•
14
Video controller.
Psion Teklogix WORKABOUT PRO HDK User Manual
Internal Scanner
Options:
- 1D Laser Scanner
- 2D Imager
- 1D Imager
5V / 3.3V
Power switch
EEPROM
SERIAL
LED
Backlight
SDRAM
128 MB
PXA270 CPU
520MHz
I2C
Power
Switch
LCD power
supplies
FLASH
MDOC 128MB
Key IRQ
2 x Side
Buttons
I2C LED
Dimmer
LCD TFT
(Full VGA
480x640)
Charge
Pump
UART
Key Scan Matrix
4-wire Touch
Panel
Backlight Control
V+3.3 /
VIN
I2C
Speaker
Speaker out
50-pin Flex Cable
3-pin Compression
Connector
Microphone
CF
Power
DC
Input
DC Input Jack
USB
Client
USB
Host
LIF Connector
(12-pin)
LIF ID
Detect
VBAT
Li-ion Battery
3.7V nominal
3000mAh /
4000mAh
Chapter 2: Hardware
Identifying Hardware
TUSB2046BI USB Hub
The TUSB2046BI USB hub, together with individual current limited load switches, provides USB
data lines and DC power to USB ports on the following connectors:
1. 100-pin expansion connector.
2. Scanner connector.
3. Tether connector.
4. LIF connector.
5. Internal USB connector.
It provides one upstream port and four downstream ports in compliance with the USB 1.1 specification. Fully-compliant USB transceivers are integrated for all upstream and downstream ports.
The downstream ports support both full-speed (12 Mbps), and low-speed (1.5 Mbps), devices by
automatically setting the slew rate according to the speed of the device attached to the ports.
WM9713 Audio Controller
The audio controller permits audio recording and playback to the AC97 specification. This chip
also handles the touchscreen digitizing input.
2.5
Identifying Hardware
An overview of the operating system and the installed hardware on the WORKABOUT PRO can
be viewed using the Control Panel. Depending on the version of Windows installed, the Control
Panel program is one of the following:
•
•
2.6
System.
About Device.
The LED
The WORKABOUT PRO has a two-coloured indicator LED to show power and charging state.
This LED can be controlled by application programs.
2.7
Connectors
For information on the external connectors that are provided on the WORKABOUT PRO, see the
specifications for each of the variants. For pinouts for the external connectors see Chapter 5: “External Connectors”.
For information on connecting devices to the 100-pin internal connector, see Chapter 7: “100-Pin
Connector”, and for connecting devices to the internal scanner connector see Chapter 8: “Scanner
Connector”.
2.8
Power Management
The WORKABOUT PRO is powered by a lithium-ion rechargeable battery pack. The
WORKABOUT PRO can be powered from external power. When the WORKABOUT PRO is
powered from external power, the battery pack also charges.
Use only power sources recommended or sold by Psion Teklogix for the WORKABOUT PRO.
Psion Teklogix WORKABOUT PRO HDK User Manual
15
Chapter 2: Hardware
Batteries
2.8.1
Batteries
The battery is a single-cell lithium-ion battery, available with capacities between 1700 mAh and
4000 mAh. When the battery charge drops below 2.6 V, the battery shuts down.
When the battery output drops below preset values, the WORKABOUT PRO power management
causes the following:
Table 2.1 Battery Threshold Voltages
Power State
2.9
Battery Voltage
WORKABOUT PRO C, S, M, ME
WORKABOUT PRO 2nd. Generation C, S
Suspend mode
Below 3.41 V
Below 3.1 V
Unit shuts down &
V_IN switches to 0 V
Below 2.6 V
Below 3.0 V
Switching The Backup Battery Power On And Off
Power from the backup battery must be switched off before inserting or removing an expansion
module. It must be switched on after the operation is complete. The backup battery switch location
differs between the WORKABOUT PRO variants.
WORKABOUT PRO C, M, ME, and S
To access the on/off switch, remove the endcap. See Figure 2.3 on page 16 for the switch position.
WORKABOUT PRO 2nd. Generation C, and S
To access the on/off switch, remove the battery cover and remove the batteries. See Figure 2.3 on
page 16 for the switch position.
Figure 2.3 WORKABOUT PRO back view showing the positions of the on/off switch
WORKABOUT PRO C, M, ME
variants (SW1401)
WORKABOUT PRO S variant
(SW1401)
Back-
Battery
WORKABOUT PRO 2nd.
Generation S variant (SW1502)
WORKABOUT PRO 2nd.
16
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 2: Hardware
Connector Locations
2.10
Connector Locations
The following diagrams show the positions of the electrical connectors on the main logic board for
the WORKABOUT PRO and the WORKABOUT PRO 2nd. Generation computers.
Figure 2.4 Connector Locations On The WORKABOUT PRO C, M, And ME
100-Pin Connector
Audio Connector
(Not supported in software)
Scanner Connector
Figure 2.5 Connector Locations On The WORKABOUT PRO S
100-Pin Connector
Scanner Connector
Audio Connector
(Not supported in software)
Psion Teklogix WORKABOUT PRO HDK User Manual
17
Chapter 2: Hardware
Connector Locations
Figure 2.6 Connector Locations On The WORKABOUT PRO 2nd. Generation C And S
USB Connector
Audio Connector
100-Pin Connector
Audio Connector
(Not supported in software)
Scanner Connector
18
Psion Teklogix WORKABOUT PRO HDK User Manual
3
SOFTWARE
3.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2 Windows Drivers . . . . . . . . . . . . . . . .
3.2.1 The Peripheral Control (PCO) Driver .
3.2.2 The PCMCIA Driver . . . . . . . . .
3.2.3 The Serial Port Driver . . . . . . . . .
3.3 Non-Psion Teklogix Drivers . . . . . . . . . . .
3.3.1 Installation . . . . . . . . . . . . . . .
3.3.2 Drivers In Windows Mobile 6 . . . . .
3.4 System Initialization . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
21
21
21
21
21
21
21
22
3.5 Registry Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.2 Registry Settings For Serial Ports . . . . . . . . . . . . . .
3.5.3 Registry Settings For Psion Teklogix Device Drivers. . . .
3.5.4 Registry Settings For Non-Psion Teklogix Device Drivers .
3.5.4.1 Loading Non-Psion Teklogix Device Drivers . . .
3.6 COM Port Assignments . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
22
22
23
23
24
24
3.7 The C++ Application Programming Interface.
3.7.1 Installing The Software . . . . . . .
3.7.2 Development Platforms . . . . . . .
3.7.3 The Interrupts Namespace . . . . . .
3.7.4 The ExpansionWakeup Namespace .
3.7.5 The GPIO Namespace . . . . . . . .
3.7.6 The EEPROM Namespace . . . . .
3.7.7 The ExpansionUSB Namespace. . .
3.7.8 The USBhub Namespace . . . . . .
3.7.9 The ScannerPort Namespace . . . .
3.7.10 The smBus Namespace. . . . . . .
3.7.11 The PCMCIA Namespace . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
25
25
26
26
26
26
26
26
27
27
27
27
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Psion Teklogix WORKABOUT PRO HDK User Manual
19
Chapter 3: Software
Overview
3.1
Overview
This chapter describes the software aspects of controlling expansion modules for the
WORKABOUT PRO.
3.2
Windows Drivers
3.2.1
The Peripheral Control (PCO) Driver
Psion Teklogix provides the peripheral control driver (PCO), a driver for the 100-pin expansion
slot. The PCO driver is a Streams driver activated very early at boot up time (it is loaded after the
File devices driver and the I2C driver).
3.2.2
The PCMCIA Driver
Hardware containing a PCMCIA slot may be connected to the 100-pin expansion slot. The PCO
driver determines whether this PCMCIA socket is present and enabled, and controls the loading of
the PCMCIA driver.
The PCMCIA driver handles both the Compact Flash and the PCMCIA socket interfaces. Since
the PCMCIA socket is itself an expansion module, the PCO driver must identify this hardware
prior to activating the PCMCIA driver.
Non-Psion Teklogix drivers may not separately activate the PCMCIA socket. You may design interfaces using the PCMCIA memory specification and interface to the hardware using the
predefined PCMCIA memory windows.
3.2.3
The Serial Port Driver
The PCO driver also controls the loading of the full-function UART serial port driver.
3.3
Non-Psion Teklogix Drivers
The Psion Teklogix platform loads some standard device drivers. If the expansion module uses
standard drivers such as PCMCIA, serial, or USB, there is no need to load customized drivers. For
information on specifying a Psion Teklogix driver see “Expansion Module EEPROM Fields” on
page 75.
3.3.1
Installation
All non-Psion Teklogix drivers must be installed in permanent storage—not in RAM. This ensures
that the driver can be activated after a cold reset.
There must be a registry entry for the driver and its parameters. For details see “Registry Keys” on
page 22.
The name of the driver must be set in the Manufacturer/Model field in the expansion module
EEPROM. For details see “Expansion Module EEPROM Fields” on page 75.
3.3.2
Drivers In Windows Mobile 6
The files required for signing drivers in Windows Mobile 6 are included in the HDK package.
Psion Teklogix WORKABOUT PRO HDK User Manual
21
Chapter 3: Software
System Initialization
3.4
System Initialization
During system startup the following occur:
1. The expansion module EEPROM is initialized and read.
2. If a non-Psion Teklogix device driver is required, it is identified from the EEPROM data
and activated. For details of this process see “Loading Non-Psion Teklogix Device Drivers” on page 24.
3. The PCMCIA/Compact Flash card driver is activated if one of the following
conditions exists:
• The PCMCIA registry key is set. See “Registry Settings For Psion Teklogix Device Drivers” on page 23.
• The Hardware type field in the expansion module EEPROM is set for a PCMCIA device.
See “Expansion Module EEPROM Fields” on page 75.
4. The full-function UART (FFUART) serial port driver is activated if one of the following
conditions exists:
• The FFUART registry key is set. See “Registry Settings For Psion Teklogix Device Drivers” on page 23.
• The Hardware type field in the expansion module EEPROM is set for a serial device. See
“Expansion Module EEPROM Fields” on page 75.
5. The USB hub is activated if one of the following conditions exists:
• The USB registry key is set. See “Registry Settings For Psion Teklogix Device Drivers” on
page 23.
• The Hardware type field in the expansion module EEPROM is set for a USB device. See
“Expansion Module EEPROM Fields” on page 75.
• A USB scanner is detected on the internal scanner port.
6. If a scanner is detected, the keyboard processor wakeup signals for the scan keys is set.
3.5
Registry Keys
3.5.1
Registry Settings For Controlling VGA
The WORKABOUT PRO VGA settings are located in the following registry subkey:
HKEY_LOCAL_MACHINE\Drivers\Display\NVDDI
Registry Values
QVGA mode (REG_DWORD)
00 = VGA
non-zero = QVGA
Note: This value is only available for the WORKABOUT PRO 2nd. Generation.
3.5.2
Registry Settings For Serial Ports
The WORKABOUT PRO serial settings are located in the following registry subkey:
HKEY_LOCAL_MACHINE\Drivers\PsionTeklogix\Serial
22
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 3: Software
Registry Settings For Psion Teklogix Device Drivers
Note: These setting are specific to the platform and should be modified with care.
Registry Values
HardwareFlowBaud (REG_DWORD)
Setting this value enables hardware RTS/CTS on the FFUART of the WORKABOUT PRO
2nd. Generation.
non-zero = the minimum baud rate where hardware flow control is enabled. The maximum rate is
921.6 k baud.
00 = enable all baud rates.
Note: This value is only available for the WORKABOUT PRO 2nd. Generation.
Index
Setting this value moves the COM port to a different location.
3.5.3
Registry Settings For Psion Teklogix Device Drivers
The WORKABOUT PRO device driver settings are located in the following registry subkey:
HKEY_LOCAL_MACHINE\Drivers\PsionTeklogix\Expansion Slot
Registry Values
FFUART (REG_DWORD)
Setting this value enables hardware RTS/STS on the FFUART of the WORKABOUT PRO 2nd.
Generation. If the key is absent, the FFUART COM1: port is not enabled.
1 = enables the full-function UART (FFUART) using the standard serial driver as COM1:.
0 = the FFUART COM1: port will not be enabled. (Default)
PCMCIA (REG_DWORD)
1 = enables the PCMCIA socket on the 100-pin connector—socket 1. The PCMCIA pins become
unavailable for other uses. The pins defined for this slot have predefined meanings and must be
adhered to in the hardware design.
0 = the PCMCIA socket is not be enabled. (Default)
USB (REG_DWORD)
1 = enables the USB hub and the 100-pin connector USB power control.
0 = neither the USB hub nor the USB power control signal will be enabled for the100-pin
connector. (Default)
Note: If the USB value is absent or has a value of 0, the expansion module USB power control can
still be controlled by the HDK API library.
3.5.4
Registry Settings For Non-Psion Teklogix Device Drivers
All non-Psion Teklogix device drivers must have a registry entry. These device driver entries are
formatted as follows:
HKEY_LOCAL_MACHINE\Drivers\PsionTeklogix\Expansion Slot\EEPROM
Psion Teklogix WORKABOUT PRO HDK User Manual
23
Chapter 3: Software
COM Port Assignments
Where: EEPROM is the name of the device driver. This is the contents of the
Manufacturer/Model field in the expansion module EEPROM. For details see “Expansion
Module EEPROM Fields” on page 75.
3.5.4.1 Loading Non-Psion Teklogix Device Drivers
At system startup the following process is used to load non-Psion Teklogix device drivers:
1. The contents of the Manufacturer/Model field in the expansion module EEPROM are
appended to the registry key
HKEY_LOCAL_MACHINE\Drivers\PsionTeklogix\Expansion Slot\
For example, if the Manufacture/Model field contains:
ACME gizmo
then the following driver is loaded:
HKEY_LOCAL_MACHINE\Drivers\PsionTeklogix\Expansion Slot\ACME gizmo
2. The DriverActivate() function uses this registry key to activate the driver.
No driver is loaded if:
•
•
The Manufacturer/Model field is not valid, or it is empty.
The derived registry key does not exist.
Note: If multiple device drivers are required for the same device, subkeys are defined. Only the
first driver is automatically activated. The application must load and activate all
additional device drivers.
3.6
COM Port Assignments
Table 3.1 Default COM-Port Assignment
COM Port
Default Assignment
WORKABOUT PRO
WORKABOUT PRO 2nd. Generation
COM0:
24
COM1:
On 100-pin expansion connector.
On 100-pin expansion connector.
COM2:
Cannot be reassigned.
Internal Bluetooth radio. If no Bluetooth is
installed, or Bluetooth is disabled, this port
goes to the serial lines on the tether port.
An adapter is required to use these lines.
Virtual serial port of the tether port. No
adapter is required to use these lines.
COM3:
Cannot be reassigned.
Internal scanner or imager.
Cannot be reassigned.
Internal scanner or imager.
COM4:
Cannot be reassigned.
USB client port—used by ActiveSync.
Cannot be reassigned.
USB client port—used by ActiveSync.
COM5:
RS-232 port A on port replicator, and serial
port available on USB-to-serial adaptor.
This port is removed in suspend and
restored on resume.
RS-232 port A on port replicator, and serial
port available on USB-to-serial adaptor.
This port is removed in suspend and
restored on resume.
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 3: Software
The C++ Application Programming Interface
Table 3.1 Default COM-Port Assignment
COM Port
Default Assignment
WORKABOUT PRO
WORKABOUT PRO 2nd. Generation
COM6:
RS-232 port B on port replicator.
This port is removed in suspend and
restored on resume.
RS-232 port B on port replicator.
This port is removed in suspend and
restored on resume.
COM7:
RS-232 port C on port replicator.
This port is removed in suspend and
restored on resume.
RS-232 port C on port replicator.
This port is removed in suspend and
restored on resume.
COM8:
Virtual port—for WWAN GSM
Virtual port—for WWAN GSM
COM9:
Cannot be reassigned.
IRCOMM port.
Cannot be reassigned.
IRCOMM port.
COM20
Not available.
Cannot be reassigned.
Internal Bluetooth radio.
COM21
Not available.
Built-in USB-Serial adapter port. This port
is removed in suspend and restored
on resume.
All COM ports can be reassigned except those marked as Cannot be reassigned. Reassignment is
done either using the Psion Teklogix COM Port Manager Control Panel program, or in the
windows registry.
Serial ports on computers with user-accessible cards are assigned dynamically—at the lowest
available COM port number—as the cards are inserted and removed.
On the WORKABOUT PRO, the maximum baud rate is 230.4 k. On the WORKABOUT PRO
2nd. Generation, the maximum rate is 921.6 k baud if RTS/CTS hardware flow control is enabled.
Bluetooth
BSP: can be used to add a Bluetooth virtual COM port. For setup instructions see the User Manual
for your WORKABOUT PRO.
Psion Teklogix Serial Endcaps
Psion Teklogix supplies endcaps with serial ports for the WORKABOUT PRO and for the
WORKABOUT PRO 2nd. Generation computers. These endcaps use the following serial ports:
•
•
•
3.7
IrDA, TTL, and RS-232 serial endcap (BR1000)—COM9:, COM0:, COM1:, and COM8:
RS-232 serial endcap (BR1001)—COM9: and COM1:
IrDA serial endcap (BR1002)—COM9: and COM0:
The C++ Application Programming Interface
The WORKABOUT PRO HDK API library enables application programs to control custom-built
hardware that connects to the 100-pin connector and the scanner connector.
3.7.1
Installing The Software
The WORKABOUT PRO HDK API library is installed as part of the Psion Teklogix Mobile
Devices SDK.
Psion Teklogix WORKABOUT PRO HDK User Manual
25
Chapter 3: Software
Development Platforms
3.7.2
Development Platforms
The following development platforms should be used with the WORKABOUT PRO HDK:
Windows
Development Environment
Windows Mobile 2003
Microsoft eMbedded Visual C++ 4.0 compiler. It is
recommended that eMbedded Visual C++ 4.0 Service Pack 3
(SP3) be installed.
Windows CE .NET 4.2
Windows Embedded CE 5.0
Windows Mobile 5
Microsoft Visual Studio 2005.
Windows Mobile 6
3.7.3
The Interrupts Namespace
This namespace is used to manage interrupts from the expansion module. The expansion module
interrupt pins are also used by the PCMCIA socket.
The following program-accessible interrupt pins are provided on the 100-pin connector:
• InputPin63
• InputPin65
If the PCMCIA driver is in use, these interrupt pins are not available.
If these pins are not used as interrupts, or by PCMCIA, they are available as GPIO.
3.7.4
The ExpansionWakeup Namespace
This namespace manages the wakeup from suspend signal on pin 79 of the 100-pin connector. The
wakeup can be enabled or disabled.
This signal is connected to the keyboard controller and is monitored from there. This pin wakes
the processor but does not generate a software-accessible interrupt.
3.7.5
The GPIO Namespace
This namespace is used to manage access to the 100-pin connector general purpose input/output
(GPIO) pins. These pins are listed in “General-Purpose I/O” on page 71.
If a full PCMCIA interface is used, some pins are not available for GPIO. These pins are identified
on Table 7.1 Pinout of the WORKABOUT PRO 100-Pin Connector on page 64.
3.7.6
The EEPROM Namespace
This namespace contains functions that access the expansion module EEPROM.
This namespace handles EEPROMS of up to 256 bytes only. Accessing EEPROMs larger than
this requires the use of the smBus namespace to communicate directly with the EEPROM. See
“The smBus Namespace” on page 27.
3.7.7
The ExpansionUSB Namespace
This namespace manages the expansion USB power controls. The USB power control signal is
output on pin 88 of the 100-pin connector.
Expansion USB power can also be enabled by the USB registry setting and by setting an appropriate value in the Hardware type field in the expansion module EEPROM. Functions in this
26
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 3: Software
The USBhub Namespace
namespace do not override these settings. For details see “Registry Settings For Psion Teklogix
Device Drivers” on page 23, and “Expansion Module EEPROM Fields” on page 75.
On the WORKABOUT PRO 2nd. Generation, the expansion USB is also available on the connector CN601 on the top of the unit. The 5 V power for this connector is also controlled by the USB
power API.
If the USB hub it is not already enabled, enabling the expansion USB also enables the USB hub.
Expansion USB power is power-managed and is automatically disabled on suspend and reenabled on resume (if it was previously enabled).
3.7.8
The USBhub Namespace
This namespace manages power to the USB hub.
3.7.9
The ScannerPort Namespace
This namespace is used to access the barcode scanner port if no internal scanner is detected.
If a built-in scanner is detected, it is managed by Scanner Control Services and the functions in
this namespace are not available. Application programs can access Scanner Control Services
through the Psion Teklogix Mobile Devices SDK.
3.7.10 The smBus Namespace
This namespace is used to manage access to I2C devices on the smBus. The smBus interface functions do not guarantee delivery as the addressed device may not be connected to the I2C bus.
Functions return appropriate errors to indicate this.
For details of the I2C bus see “I2C Device Identification” on page 73.
3.7.11 The PCMCIA Namespace
This namespace is used to access PCMCIA bus functions, if a full PCMCIA function is not in use.
Details of the PCMCIA interface can be found in the Marvell PXA255 and PXA270
Developer Manuals.
These functions return errors if the PCMCIA socket is already in use. In this case, the standard
PCMCIA driver manages the memory windows.
The PCMCIA timing functions are processor specific and fail if called on the wrong platform.
Psion Teklogix WORKABOUT PRO HDK User Manual
27
4
MECHANICAL CONSIDERATIONS
4.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.2 HDK Mechanical Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.3 Installation . . . . . . . . . . . . . . . . . . . . .
4.3.1 Endcap-Mounted Device Installation . .
4.3.2 Backplate-Mounted Device Installation .
4.3.3 Expansion Module Installation . . . . .
4.4 Location And Construction . . . . . . . . . . . .
4.4.1 Materials . . . . . . . . . . . . . . . . .
4.4.2 Backplate-Mounted Device . . . . . . .
4.4.3 Expansion Module . . . . . . . . . . . .
4.4.3.1 100-Pin Connector . . . . . . .
4.4.3.2 Mounting Frame . . . . . . . .
4.4.4 Endcap, Card Stop, And Stylus . . . . .
4.4.5 Bottom Footprint. . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Psion Teklogix WORKABOUT PRO HDK User Manual
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
33
33
33
34
34
34
35
35
35
36
36
37
29
Chapter 4: Mechanical Considerations
Overview
4.1
Overview
This chapter describes the physical connectors, space, and mounting of an expansion module, a
backplate-mounted device, and an endcap-mounted device.
4.2
HDK Mechanical Files
The Hardware Development Kit provides the following mechanical models and drawings:
WORKABOUT PRO All Variants
IGES Files
Description
File Name
Backplate
...\Mechanical\WORKABOUTPRO\iges_files
\backplate.igs
Endcap
...\Mechanical\WORKABOUTPRO\iges_files
\endcap.igs
Endcap assembly
...\Mechanical\WORKABOUTPRO\iges_files
\endcap_assembly.igs
Stylus pen
...\Mechanical\WORKABOUTPRO\iges_files
\stylus_pen.igs
Sample PCMCIA expansion card
...\Mechanical\WORKABOUTPRO\iges_files
\pcmcia_xmod.igs
PDF Files
Description
File Name
2D backplate
...\Mechanical\WORKABOUTPRO\pdf
\backplate.pdf
2D endcap
...\Mechanical\WORKABOUTPRO\pdf
\endcap.pdf
2D endcap assembly
...\Mechanical\WORKABOUTPRO\pdf
\endcap_assembly.pdf
2D ball for endcap
...\Mechanical\WORKABOUTPRO\pdf
\endcap_assembly_ball.pdf
2D endcap ball holder
...\Mechanical\WORKABOUTPRO\pdf
\endcap_assembly_ball_holder.pdf
2D endcap, and ball spring
...\Mechanical\WORKABOUTPRO\pdf
\endcap_assembly_ball_spring.pdf
2D stylus gasket for endcap
...\Mechanical\WORKABOUTPRO\pdf
\endcap_assembly_stylus_rubber.pdf
2D stylus pen
...\Mechanical\WORKABOUTPRO\pdf
\stylus_pen.pdf
Psion Teklogix WORKABOUT PRO HDK User Manual
31
Chapter 4: Mechanical Considerations
HDK Mechanical Files
WORKABOUT PRO
IGES Files
Description
File Name
Body shell—WORKABOUT PRO C, M, ME
...\Mechanical\WORKABOUTPRO\iges_files
\colour_mono_terminal.igs
Body shell—WORKABOUT PRO S
...\Mechanical\WORKABOUTPRO\iges_files
\short_terminal.igs
Mounting frame
...\Mechanical\WORKABOUTPRO\pdf
\internal_metal_frame.pdf
Mechanical card stop
...\Mechanical\WORKABOUTPRO\iges_files
\mechanical_stop.igs
PDF Files
Description
File Name
2D Body shell—WORKABOUT PRO C, M, ME
...\Mechanical\WORKABOUTPRO\pdf
\housing_body.pdf
2D Body shell—WORKABOUT PRO S
...\Mechanical\WORKABOUTPRO\pdf
\housing_body.pdf
2D Mounting frame
...\Mechanical\WORKABOUTPRO\pdf
\internal_metal_frame.pdf
2D mechanical card stop
...\Mechanical\WORKABOUTPRO\pdf
\mechanical_stop.pdf FIX
WORKABOUT PRO 2nd. Generation
IGES FIles
Description
32
File Name
Body shell—WORKABOUT PRO 2nd.
Generation C
...\Mechanical\WORKABOUTPRO\G2\iges_files
\G2_C_body.igs
Body shell—WORKABOUT PRO 2nd.
Generation S
...\Mechanical\WORKABOUTPRO\G2\iges_files
\G2_S_body.igs
Mounting frame
...\Mechanical\WORKABOUTPRO\G2\iges_files
\G2_mounting_frame.igs
Mechanical card stop
...\Mechanical\WORKABOUTPRO\G2\iges_files
\mechanical_stop.igs
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 4: Mechanical Considerations
Installation
PDF FIles
Description
File Name
2D Mechanical card stop
...\Mechanical\WORKABOUTPR\G2\pdf
\mechanical_stop.pdf
4.3
Installation
4.3.1
Endcap-Mounted Device Installation
The endcap is attached with four M2.6 x 8 screws. Removing and installing it requires a
#1 Phillips screwdriver.
To remove the endcap:
1. Remove the four screws.
2. Remove the endcap.
3. If necessary, remove the card stop to gain access to the CF or PCMCIA cards.
To install the endcap:
1. Insert and fasten the card stop, if necessary.
2. Insert the endcap.
3. Insert and tighten the four screws. Torque them to 0.339 N m (3.0 lb in).
When a PCMCIA card or Compact Flash card is inserted into the WORKABOUT PRO, a mechanical card stop must be inserted before the endcap is attached, to prevent the card from moving
out of place. This card stop is attached with either two or four M2 x 4 screws. Use a #1 Phillips bit
for them, and torque to 0.226 N m (2.0 lb in).
4.3.2
Backplate-Mounted Device Installation
Customized hardware can be mounted on the inside of the backplate of the WORKABOUT PRO.
Several Psion Teklogix scanner modules are mounted on scanner-specific backplates.
There are a number of scanner kits available for the WORKABOUT PRO. These include scanner
backplates, scanner endcaps, and mounting hardware. For a list of Psion Teklogix scanner kits see
the Accessories Catalog at www.PsionTeklogix.com/Accessories.
The backplate is fastened to the back of the WORKABOUT PRO using six M2.6 x 4 screws. Use
a #1 Phillips screwdriver to insert and remove them.
Follow these steps:
Important: Make sure all external power is removed from the WORKABOUT PRO before
starting to install the device.
1. Disconnect the WORKABOUT PRO from external power.
2. Remove the WORKABOUT PRO battery.
3. Switch off the backup battery power. For instructions see “Switching The Backup Battery
Power On And Off” on page 16.
4. Remove the backplate of the WORKABOUT PRO.
Psion Teklogix WORKABOUT PRO HDK User Manual
33
Chapter 4: Mechanical Considerations
Expansion Module Installation
5. Connect the device to the appropriate socket on the main logic board.
6. Place the new backplate assembly on the WORKABOUT PRO.
7. Fasten the six screws.They can be tightened in any order. Torque them to 0.283 N m
(2.5 lb in).
8. Switch on the backup battery power. For instructions see “Switching The Backup Battery
Power On And Off” on page 16.
9. Connect the WORKABOUT PRO to a power supply and/or insert the battery.
4.3.3
Expansion Module Installation
The expansion board is fastened to the metal frame inside the WORKABOUT PRO by four
M2.6 x 4 screws. Installing it requires the following tools:
• #1 Phillips screwdriver.
To install the expansion module:
1. Disconnect the WORKABOUT PRO from external power.
2. Remove the WORKABOUT PRO battery.
3. Switch off the backup battery power. For instructions see “Switching The Backup Battery
Power On And Off” on page 16.
4. Remove the backplate.
5. Insert the expansion module through the back of the computer as shown here:
6. Fasten the expansion module to the frame with four M2 x 4 screws.
7. Attach the backplate. Torque the 6 screws to 0.283 N m (2.5 lb in).
8. Switch on the backup battery power. For instructions see “Switching The Backup Battery
Power On And Off” on page 16.
9. Connect the WORKABOUT PRO to a power supply and/or insert the battery.
4.4
Location And Construction
4.4.1
Materials
The recommended material for endcaps and backplates for the WORKABOUT PRO is GE C1200
plastic (standard black). The recommended texturing is AT-IM002, 0.035mm deep, or MT11030.
Both the card stop and the ball holder used in the endcap assembly are also made of this material.
34
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 4: Mechanical Considerations
Backplate-Mounted Device
4.4.2
Backplate-Mounted Device
The backplate-mounted device must fit within the backplate of the WORKABOUT PRO. It can
project inwards into the WORKABOUT PRO to a varying distance, depending on other options
installed within the WORKABOUT PRO.
The greatest amount of room is found within a WORKABOUT PRO that has no expansion
module installed. To prevent interference with expansion cards, the backplate-mounted device, or
the backplate itself, must not protrude into the terminal plastic housing by more than 3 mm.
This HDK provides IGES models of the backplate, and of the bodies of the WORKABOUT PRO
variants. See the list of IGES files in “HDK Mechanical Files” on page 31.
Consult the 2D drawing of the backplate for the backplate hole locations.
To maintain sealing, and the IP rating, the sealing rib of the backplate must have a height of
0.60 mm and a width of 0.5 mm.
To maintain compliance with the WORKABOUT PRO drop test specification, backplates and
scanner devices must not weigh more than 90 g (0.2 lb) in total, the same weight as the SE1223
backplate/scanner module combination. The shape of the backplate influences the outcome of
drop testing.
4.4.3
Expansion Module
Expansion modules must fit within the perimeter of the WORKABOUT PRO metal mounting
frame. They cannot exceed a height of 5.5 mm, as measured from the underside of the module
towards the display of the WORKABOUT PRO. The holes that connect the card stop must not be
covered.
Only the 100-pin connector should be placed on the under side of the expansion board. Other
components on the underside can interfere with the following:
•
On the WORKABOUT PRO C, S, M, ME:
- the backup battery, or
- the CF card and socket.
•
On the WORKABOUT PRO 2nd. Generation C, S:
- the SD card slot, or
- the CF card and socket.
In addition, it must be possible to insert the completed expansion card through the backplate
opening of the WORKABOUT PRO. This is especially important if the card is longer than the
backplate opening.
The HDK provides IGES models of the mounting frames for the WORKABOUT PRO variants.
An IGES model for a sample PCMCIA expansion module is also included. See the list of IGES
files in “HDK Mechanical Files” on page 31.
4.4.3.1 100-Pin Connector
The 100-pin connector on the WORKABOUT PRO main logic board is an FX6-100P-0.8SV2
header. The mating connector is an FX6-100S-0.8SV2.
The centre of the connector on the expansion module must be aligned on the centre line of the
mounting frame. The connector is mounted in the following location on all WORKABOUT
PRO variants:
Psion Teklogix WORKABOUT PRO HDK User Manual
35
Chapter 4: Mechanical Considerations
Endcap, Card Stop, And Stylus
Figure 4.1 Location Of 100-Pin Connector On Expansion Module (Measurements In mm)
Back view with the
backplate removed
4.4.3.2 Mounting Frame
There are some differences between the mounting frames for the WORKABOUT PRO and the
WORKABOUT PRO 2nd. Generation. In particular, the mounting frame for the WORKABOUT
PRO 2nd. Generation is 1mm higher. Refer to the IGES models for details.
The relative positions of the screw holes for attaching the expansion module to the mounting
frame are the same for all variants of the WORKABOUT PRO.
4.4.4
Endcap, Card Stop, And Stylus
The endcap and card stop fit onto the end of the WORKABOUT PRO. The endcap assembly
includes parts (a metal ball, a spring, and a plastic ball holder) to retain the stylus.
The IGES models of the bodies of the WORKABOUT PRO variants, show the hole for the stylus
See “HDK Mechanical Files” on page 31 for a list of detailed drawing and IGES models for the
endcap assembly and all its parts as well as the IGES model of the WORKABOUT PRO bodies.
The standard endcap is 83.35 mm long, 25.40 mm wide, and 23.87 mm deep. To maintain the existing drop test specifications, customized endcaps must not weigh more than 22 g (0.05 lb).
To maintain IP sealing, the endcap sealing rib must have a height and width of 0.8 mm. If the
stylus is to be used then it must be sealed against the stylus holder using the rubber stylus gasket.
The shape of the endcap influences the outcome of drop testing.
It is important that the correct card stop is fitted. It must fit into the internal frame and housing
with no interference to the endcap.
Consult the drawings for information on which card stops are used in each WORKABOUT PRO
variant, and which card stops are used with each card type.
36
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 4: Mechanical Considerations
Bottom Footprint
4.4.5
Bottom Footprint
The HDK provides models of the bases of the WORKABOUT PRO variants. These show the positions of the connectors. These models also provide the outside dimensions. See also Figure 5.1
on page 41 and Figure 5.3 on page 43.
These models are as follows:
Table 4.1 IGES Models Of The WORKABOUT PRO Body
Type Of Model
Filename
Body of WORKABOUT PRO (M, ME, and C variant)
colour_mono_terminal.igs
Body of WORKABOUT PRO (S variant)
short_terminal.igs
Body of WORKABOUT PRO 2nd. Generation
(S variant)
G2_S_body.igs
Body of WORKABOUT PRO 2nd. Generation
(C variant)
G2_C_body.igs
Psion Teklogix WORKABOUT PRO HDK User Manual
37
5
EXTERNAL CONNECTORS
5.1 Overview Of External Connectors, Cables, And Accessories. . . . . . . . . . . . . . . . . . . . . . 41
5.2 External Connectors On The WORKABOUT PRO . . . . . . . . . . . . .
5.2.1 WORKABOUT PRO C, S, M, ME . . . . . . . . . . . . . . . . .
5.2.2 WORKABOUT PRO 2nd. Generation C, S. . . . . . . . . . . . .
5.3 The LIF Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3.1 Sensing Device Presence . . . . . . . . . . . . . . . . . . . . . .
5.4 The Tether Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4.1 The WORKABOUT PRO C, S, M, ME Tether Connector . . . . .
5.4.1.1 COM2: Serial Port . . . . . . . . . . . . . . . . . . . . .
5.4.1.2 Sensing Device Presence . . . . . . . . . . . . . . . . . .
5.4.2 The WORKABOUT PRO 2nd. Generation C, S Tether Connector
5.4.2.1 Sensing Device Presence . . . . . . . . . . . . . . . . . .
5.4.3 Cables For the Tether Connector . . . . . . . . . . . . . . . . . .
5.5 The WORKABOUT PRO C, S, M, ME Audio Connector . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
41
41
42
44
44
44
44
45
46
47
48
48
48
5.6 Docking Stations. . . . . . . . . . . . . . . . . . . . . . . . . .
5.6.1 Single Unit Docking Stations . . . . . . . . . . . . . .
5.6.1.1 The USB Host Connector . . . . . . . . . . .
5.6.1.2 The USB Client Connector . . . . . . . . . . .
5.6.2 Four Unit Multi-Dock Docking Station (Quad Docker)
5.7 Vehicle Cradles . . . . . . . . . . . . . . . . . . . . . . . . . .
5.7.1 The Vehicle Cradle 15-Pin Connector . . . . . . . . . .
5.8 Port Replicator . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.1 The Serial Connectors . . . . . . . . . . . . . . . . . .
5.9 Other Cables And Adaptors . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
49
49
50
50
51
52
53
54
56
56
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
5.10 Mechanical Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Psion Teklogix WORKABOUT PRO HDK User Manual
39
Chapter 5: External Connectors
Overview Of External Connectors, Cables, And Accessories
5.1
Overview Of External Connectors, Cables, And Accessories
This chapter describes the connectors on the WORKABOUT PRO and on selected accessories. It
also describes cables and accessories that connect to them, and how they function in the WORKABOUT PRO system.
5.2
External Connectors On The WORKABOUT PRO
5.2.1
WORKABOUT PRO C, S, M, ME
The WORKABOUT PRO computers have three external connectors:
• LIF connector.
• Tether connector.
• Audio connector.
The LIF connector connects the WORKABOUT PRO to docking stations and cradles. The tether
connector connects to scanners, AC adaptors, USB or serial adaptors, and other accessories.
The audio connector accepts headphones and microphones.
Figure 5.1 WORKABOUT PRO Base Showing External Connectors
LIF Connector
Tether Connector
Audio Connector
Psion Teklogix WORKABOUT PRO HDK User Manual
41
Chapter 5: External Connectors
WORKABOUT PRO 2nd. Generation C, S
Figure 5.2 External Connectors On The WORKABOUT PRO C, S, M, ME
WM9075
Audio Connector
MQ1188
USB Host
LIF Connector
USB host 4
LIF_DETECT
USB Client 0
V_IN
Data bus
Address bus
USB host 3
Control bus
TETHER_DETECT
Switch
COM2
Main processor
To Bluetooth transceiver
DC_IN
Power to other parts of the
V_IN
WORKABOUT PRO system
V_BAT
Tether Connector
Battery
Switch
Charger
5.2.2
WORKABOUT PRO 2nd. Generation C, S
The WORKABOUT PRO 2nd. Generation computers have the following external connectors:
•
•
•
42
LIF connector
Tether connector.
Power connector.
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 5: External Connectors
WORKABOUT PRO 2nd. Generation C, S
Figure 5.3 WORKABOUT PRO 2nd. Generation Base Showing External Connectors
Tether connector
LIF connector
DC connector
Figure 5.4 External Connectors On The WORKABOUT PRO 2nd. Generation C, S
Psion Teklogix WORKABOUT PRO HDK User Manual
43
Chapter 5: External Connectors
The LIF Connector
5.3
The LIF Connector
The LIF connector gives access to the following:
•
•
•
•
5.3.1
USB host port 4.
USB client port 0.
LIF port device detection.
Power input to the WORKABOUT PRO.
Sensing Device Presence
For device identification the following pull-down resistor must be connected between
LIF_DETECT (pin 8) and ground:
Pull-down Resistor
Device
100 kΩ, 1/8 W, 5%
USB host.
The Psion Teklogix Mobile Devices SDK enables a software application to detect and identify the
connected device.
5.4
The Tether Connector
5.4.1
The WORKABOUT PRO C, S, M, ME Tether Connector
The tether connector gives access to the following:
•
USB host port 3 (WORKABOUT PRO), or USB host or device (WORKABOUT PRO
2nd. Generation).
COM2: data lines if Bluetooth not enabled.
Tether port device detection.
Power input to the WORKABOUT PRO.
•
•
•
Table 5.1 Pinout Of The WORKABOUT PRO Tether Connector
Pin
Name
Description
State
When
Active
State
During
Sleep
Pull-up Or
Pull-down
1
GND
Ground.
Power
N/A
N/A
N/A
2
USB_H3_D+
USB Host port 3 D+.
Input/
output
B
Low
Pulled
down
15 kΩ
3
USB_H3_D-
USB Host port 3 D-.
Input/
output
B
Low
Pulled
down
15 kΩ
4
USB_H3_PWR
USB Host port 3 power. Power
N/A
Off
N/A
Abbreviations:
N/A= not applicable;
B = both high and low.
44
Direction
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 5: External Connectors
The WORKABOUT PRO C, S, M, ME Tether Connector
Table 5.1 Pinout Of The WORKABOUT PRO Tether Connector
Pin
Name
Description
Direction
State
When
Active
State
During
Sleep
Pull-up Or
Pull-down
5
TXD
COM2: available if
Bluetooth is
not enabled.
Output
B
Low
6
RXD
COM2: available if
Bluetooth is
not enabled.
Input
B
Pulled up Pulled up
100 kΩ
7
TETHER_DETECT Input for detection of
device on tether
connector.
Input
B
Pulled up Pulled up
100 kΩ
8
DC_IN
Power supply to
WORKABOUT PRO.
Power
input
N/A
N/A
N/A
Reserved
Reserved.
Do not connect.
N/A
N/A
N/A
N/A
PGND
Ground.
Power
N/A
N/A
N/A
9
None
10
11
12
13
14
15
16
17
18
Abbreviations:
N/A= not applicable;
B = both high and low.
5.4.1.1 COM2: Serial Port
For details of COM port assignments on the WORKABOUT PRO see “COM Port Assignments”
on page 24.
WORKABOUT PRO M
The data lines on pins 5 and 6 are always available.
WORKABOUT PRO C and S
COM2: data lines are only available on pins 5 and 6 when the integrated Bluetooth feature is
disabled.
Important: These serial lines are not at RS-232 specifications.
They are connected directly to the WORKABOUT PRO main logic board. They
are at CMOS levels, between 3.3 V and ground, and are unbuffered.
Psion Teklogix WORKABOUT PRO HDK User Manual
45
Chapter 5: External Connectors
The WORKABOUT PRO C, S, M, ME Tether Connector
Using Windows to enable and disable Bluetooth
For instructions consult the user manual for your WORKABOUT PRO. For a list of user manuals
see Appendix B: “Resources”.
Using BooSt to enable the serial lines on the tether connector
To enable the serial lines through the tether connector, issue the following command at the BooSt
console prompt:
>config set flags
BooSt responds with a command-specific prompt:
Flags (hex or +/-bit#>)>
At this prompt, enter the command:
+0
This sets flag 0. The WORKABOUT PRO responds with:
bit0=NoBluetooth
The Bluetooth transceiver is now disabled.
Using BooSt to enable Bluetooth
The enable the integrated Bluetooth, issue the following command at the BooSt console prompt:
>config set flags
BooSt responds with a command-specific prompt:
Flags (hex or +/-bit#>)>
At this prompt enter the command:
-0
This clears flag 0. The WORKABOUT PRO responds with:
bit0=Bluetooth
>
The Bluetooth transceiver is now enabled.
5.4.1.2 Sensing Device Presence
For device identification, within the connected cable, one of the following pull-down resistors
must be connected between TETHER_DETECT (pin 7) and ground:
Pull-down Resistor
Device
100 kΩ
USB host.
200 kΩ
USB client.
49.9 kΩ
USB serial.
The Psion Teklogix Mobile Devices SDK enables a software application to detect and identify the
connected device.
46
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 5: External Connectors
The WORKABOUT PRO 2nd. Generation C, S Tether Connector
5.4.2
The WORKABOUT PRO 2nd. Generation C, S Tether Connector
The tether connector gives access to the following:
•
•
•
•
USB port.
COM2:
Tether port device detection.
Power input to the WORKABOUT PRO.
Table 5.2 Pinout Of The WORKABOUT PRO 2nd. Generation Tether Connector
Pin
Name
Description
Direction
State
When
Active
State
During
Sleep
Pull-up Or
Pull-down
1
GND
Ground.
Power
N/A
N/A
N/A
2
USB_D+
USB D+
(host or device)
Input/
output
B
Low
Pulled
down
15 kΩ
3
USB_D-
USB D(host or device)
Input/
output
B
Low
Pulled
down
15 kΩ
4
USB_PWR
USB Device
Power Detect
Power
N/A
Off
N/A
5
TXD
COM2:
Output
B
Low
None
6
RXD
COM2:
Input
B
Pulled up Pulled up
100 kΩ
7
TETHER_DETECT Input for detection of
device on
tether connector.
Input
B
Pulled up Pulled up
49.9 kΩ
8
DC_IN
Power supply to
WORKABOUT PRO.
Power
input
N/A
N/A
11
CTS
COM2:
Input
12
RTS
COM2:
Output
13
DSR
COM2:
Input
14
DTR
COM2:
Output
15
DCD
COM2:
Input
16
RI
COM2:
Input
17
GND
Ground
Power
18
GND
Ground
Power
9
N/A
10
Abbreviations:
N/A= not applicable;
B = both high and low,
Psion Teklogix WORKABOUT PRO HDK User Manual
47
Chapter 5: External Connectors
Cables For the Tether Connector
5.4.2.1 Sensing Device Presence
For device identification, in the connected cable, one of the following pull-down resistors must be
connected between TETHER_DETECT (pin 7) and ground:
Pull-down Resistor
Device
200 kΩ
USB client.
100 kΩ
USB host.
49.9 kΩ
USB serial.
The Psion Teklogix Mobile Devices SDK enables a software application to detect and identify the
connected device.
5.4.3
Cables For the Tether Connector
Psion Teklogix provides cables that connect to the tether port of the WORKABOUT PRO. For a
complete list see www.PsionTeklogix.com/Accessories.
These cables include the following:
•
•
•
5.5
Tether to RS-232-C cable for the WORKABOUT PRO 2nd. Generation.
Tether to USB-B for the WORKABOUT PRO 2nd. Generation.
Tether to USB-A for all WORKABOUT PRO variants.
The WORKABOUT PRO C, S, M, ME Audio Connector
The audio connector is only available on the WORKABOUT PRO C, S, M, and ME. It is not
available on the WORKABOUT PRO 2nd. Generation computers.
The audio connector has the following pinout:
Table 5.3 Pinout Of The Audio Connector
Pin
Signal Name
Description
1
SP+R
Right speaker positive.
2
MIC+
Microphone positive.
3
SP+L
Left speaker positive.
4
GND
Ground.
The audio connector accepts a standard 2.5 mm stereo minijack.
Figure 5.5 Audio Plug
GND
48
Psion Teklogix WORKABOUT PRO HDK User Manual
SP+L
MIC+
SP+L
Chapter 5: External Connectors
Docking Stations
5.6
Docking Stations
A docking station is a desk-top unit that can hold one or more WORKABOUT PRO computers.
The docking station and the WORKABOUT PRO communicate through the LIF port.
Refer to the Accessories Catalog at www.PsionTeklogix.com/Accessories for the docking stations
that are available for your WORKABOUT PRO model.
5.6.1
Single Unit Docking Stations
A single unit docking station can hold only one WORKABOUT PRO. The following illustration
shows a typical single unit docking station:
Figure 5.6 Single Unit Docking Station
All single unit docking stations have the following connectors:
• USB host connector.
• USB client connector.
• DC input connector.
When external power is supplied to the docking station, the WORKABOUT PRO battery undergoes charging. These units also have a spare battery charging well.
If no external power is supplied to the docking station, the USB ports are still functional.
Figure 5.7 Docking Station Block Diagram
Psion Teklogix WORKABOUT PRO HDK User Manual
49
Chapter 5: External Connectors
Single Unit Docking Stations
5.6.1.1 The USB Host Connector
The USB Host connector on the docking station connects the docked WORKABOUT PRO, as a
USB host, to an external USB client device. It uses a USB Type A receptacle.
Figure 5.8 USB Host Connector
Pin 1
Pin 2
Pin 3
Pin 4
USB Host
Connector
Table 5.4 Pinout Of The USB Host Connector
Pin
Pin On LIF
Connector
1
Name
Description
Direction
Vbus
DC supply from the WORKABOUT PRO. Current 500
mA maximum; voltage
minimum 4.35 V, maximum
5.25 V
Output to connected
external device.
Bidirectional (half-duplex).
2
4
USB_H4_D-
USB Host port 4 D-.
3
3
USB_H4_D+
USB Host port 4 D+.
4
2
Ground
5.6.1.2 The USB Client Connector
The USB client connector on the docking station connects an external device, as a USB client, to
the docked WORKABOUT PRO. It uses a USB Type B receptacle.
Figure 5.9 USB Client Connector
Pin 2
Pin 3
50
Psion Teklogix WORKABOUT PRO HDK User Manual
Pin 1
Pin 4
Chapter 5: External Connectors
Four Unit Multi-Dock Docking Station (Quad Docker)
Table 5.5 Pinout Of The USB Client Connector
Pin
Pin On LIF
Connector
1
5.6.2
Name
Description
Direction
Vbus
DC current from external
host. This pin is unconnected
inside the docking station.
Input from connected
external device.
Bidirectional (half-duplex).
2
10
USB_C0_D-
USB Client port 0 D-.
3
9
USB_C0_D+
USB Client port 0 D+.
4
2
Ground
Four Unit Multi-Dock Docking Station (Quad Docker)
A multi-dock docking station can hold up to four WORKABOUT PRO computers. The docking
station and the WORKABOUT PRO computers communicate through the LIF ports of the
WORKABOUT PROs. The following illustration shows a typical multi-dock docking station:
Figure 5.10 A Multi-Dock Docking Station
All multi-dock docking stations have the following connectors:
• Ethernet connector.
• DC input connector.
When external power is supplied to the docking station, the batteries in the WORKABOUT PROs
undergo charging.
If no external power is supplied to the docking station, the ethernet port is still functional.
The USB Host interfaces from each WORKABOUT PRO are connected to USB-to-ethernet converters inside the docking station. Each USB-to-ethernet converter has a separate MAC address.
All are connected to a common ethernet hub, which is connected to the single external ethernet
connector. The ethernet connector is a standard 10BASE-T twisted pair connector.
Psion Teklogix WORKABOUT PRO HDK User Manual
51
Chapter 5: External Connectors
Vehicle Cradles
Figure 5.11 The Multi-Dock Docking Station Block Diagram
Workabout Pro
Workabout Pro
Workabout Pro
USB-to-Ethernet
converter
USB-to-Ethernet
converter
USB host
connections
USB-to-Ethernet
converter
LIF Connector
USB host 4
USB-to-Ethernet
converter
10-base2 Ethernet
DC Power to LIF connectors for
other three Workabout Pro units
DC_IN
DC Power to
Quad Cradle
circuitry
Ethernet Hub
Power-conditioning
circuitry
Quad Cradle
Ethernet connector
External DC Power (5 V)
5.7
Vehicle Cradles
A vehicle cradle holds a single WORKABOUT PRO. The cradle and the WORKABOUT PRO
computer communicate through the LIF port of the WORKABOUT PRO.
Every cradle has the following connector:
• 15-pin vehicle cradle connector.
Some cradles are powered from the vehicle battery: others are unpowered. For information on the
cradles available for your WORKABOUT PRO see the Accessories Catalog at
www.PsionTeklogix.com/Accessories.
52
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 5: External Connectors
The Vehicle Cradle 15-Pin Connector
Figure 5.12 Typical Vehicle Cradle
Figure 5.13 Vehicle Cradle Block Diagram
5.7.1
The Vehicle Cradle 15-Pin Connector
All cradles have an attached cable that is terminated by a female DE-15 connector.
Table 5.6 Pinout Of The Vehicle Cradle 15-Pin Connector
Pin
Pin On LIF
Connector
Name
Description
Direction
1
1
PGND
Ground.
Power
2
2
GND
Ground.
Power
3
3
USB_H4_D+
USB host port 4 D+.
Bidirectional
4
4
USB_H4_D-
USB host port 4 D-.
Bidirectional
5
5
USB_H4_PWR
USB host port 4 power.
Power
6
6
DC_IN
Power input
7
7
Power supply to
WORKABOUT PRO.
Psion Teklogix WORKABOUT PRO HDK User Manual
53
Chapter 5: External Connectors
Port Replicator
Table 5.6 Pinout Of The Vehicle Cradle 15-Pin Connector
Pin
Pin On LIF
Connector
Name
Description
Direction
8
8
LIF_DETECT
Input for detection of device on
LIF connector
Input
9
9
USB_C0_D+
USB client port 0 D+.
Bidirectional
10
10
USB_C0_D-
USB client port 0 D-.
Bidirectional
11
11
GND
Ground.
Power
12
12
PGND
Ground.
Power
13
14
15
5.8
Port Replicator
The port replicator allows peripherals to be attached to the powered and unpowered
vehicle cradles. The WORKABOUT PRO and the port replicator communicate through the
LIF port.
The port replicator has the following connectors:
• Three RS-232 ports.
• USB client connector.
• 15-pin vehicle cradle connector.
For information on the port replicators available for your WORKABOUT PRO see the Accessories Catalog at www.PsionTeklogix.com/Accessories
The port replicator provides three full-function RS-232 ports on DE-9 connectors. The RS-232
ports are connected to an internal processor which is connected as a client to the USB host interface of the WORKABOUT PRO. For the port assignments see “COM Port Assignments” on
page 24.
For the pinout for the USB client connector see “The USB Client Connector” on page 50.
For the pinout for the 15-pin vehicle cradle connector see “The Vehicle Cradle 15-Pin Connector”
on page 53.
The.WORKABOUT PRO supplies 5 V DC to the cradle and the port replicator through the
5 V DC supply associated with the USB host port (pin 5) on the LIF connector. The cradle
switches this 5 V on when the WORKABOUT PRO is docked in the cradle. The port replicator
draws a maximum of 50 mA when no peripherals are connected to it.
The DC input of the powered cradle is regulated and fed only to the power input of the
WORKABOUT PRO.
54
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 5: External Connectors
Port Replicator
Figure 5.14 The Port Replicator
Figure 5.15 Port Replicator Block Diagram
The cradle passes the USB Host and USB Client connections to the Port Replicator. The USB
Host connection also supplies DC power to the Port Replicator.
Inside the port replicator, the USB host signals from the WORKABOUT PRO are connected to a
processor that provides the three sets of serial port signals. The USB client lines are connected to
the USB client connector.
Psion Teklogix WORKABOUT PRO HDK User Manual
55
Chapter 5: External Connectors
The Serial Connectors
5.8.1
The Serial Connectors
The three serial connectors use male DE-9 connectors and are DTE devices.
Table 5.7 Pinout Of The Serial Connector
Pin
5.9
Name
Direction
(relative to the Port Replicator)
Description
1
CD
Carrier Detect
Input
2
RD
Receive Data:
Data to the Port Replicator
Input
3
TD
Transmit Data:
Data from the Port Replicator
Output
4
DTR
Data Terminal Ready
Output
5
Signal Ground Ground
-
6
DSR
Data Set Ready
Input
7
RTS
Request To Send
Output
8
CTS
Clear To Send
Input
9
RI
Ring Indicator
Input
Other Cables And Adaptors
Psion Teklogix supplies several cables and adapters that connect to the WORKABOUT PRO, the
docking station, and the vehicle cradle, ports. See the Accessories Catalog at www.PsionTeklogix.com/Accessories for information.
5.10
Mechanical Considerations
The WORKABOUT PRO HDK provides 3D models of the outsides of the WORKABOUT PRO
variants to aid in sizing devices that accept the computer and in locating and aligning the connectors within them.
The tether connector is intended for free-standing cables. Clearance should be provided around it.
56
Psion Teklogix WORKABOUT PRO HDK User Manual
6
INTERNAL CONNECTORS
6.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
6.2 WORKABOUT PRO 2nd. Generation C, S Audio Connector
6.2.1 Cables . . . . . . . . . . . . . . . . . . . . . . . .
6.3 WORKABOUT PRO 2nd. Generation C, S USB Connector .
6.3.1 Cables . . . . . . . . . . . . . . . . . . . . . . . .
6.4 100-Pin Connector . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
59
59
59
60
60
6.5 Scanner Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Psion Teklogix WORKABOUT PRO HDK User Manual
57
Chapter 6: Internal Connectors
Overview
6.1
Overview
This chapter describes the WORKABOUT PRO internal connectors that are not described elsewhere in this manual. For a diagram of the locations of all the internal connectors see “Connector
Locations” on page 17.
6.2
WORKABOUT PRO 2nd. Generation C, S Audio Connector
All WORKABOUT PRO 2nd. Generation computers have an internal audio connector. This connector accepts a 3.5 mm stereo connector. Psion Teklogix supplies a cable that connects to this
socket. For information see the Accessories Catalog at www.PsionTeklogix.com/Accessories.
Table 6.1 Pinout Of The Internal Audio Connector
Pin
Name
Function
Notes
1
HPOUTR_C
Headset right channel
2
HPOUTL_C
Headset left channel
3
HSET_IN
Headset input detect
4
GND
Ground
Recommended colour is black.
5
MIC_EXT
Microphone
Audio input for connection to a microphone.
Full scale input signal level is 1 Vrms.
6
CONNECTOR_DETECT Cable
All different colours; do not use red.
This pin must be grounded within the
cable, or connected to pin 4.
Pin 1 and pin 3 must not be connected on the cable.
When a cable is connected to this audio connector, the microphone on the keyboard
is disconnected.
6.2.1
Cables
The following open-ended cable is available from Psion Teklogix:
•
6.3
Part Number. 1050987.
WORKABOUT PRO 2nd. Generation C, S USB Connector
All WORKABOUT PRO 2nd. Generation computers have an internal USB connector.
Psion Teklogix supplies a cable that connects to this socket. For information see the Accessories
Catalog at www.PsionTeklogix.com/Accessories.
This connector shares signals with the 100-pin connector. So, it is described in the same chapter as
the 100-pin connector. For details see “WORKABOUT PRO 2nd. Generation C, S USB Connector” on page 77.
Psion Teklogix WORKABOUT PRO HDK User Manual
59
Chapter 6: Internal Connectors
Cables
6.3.1
Cables
The following cables are available from Psion Teklogix:
Part Number
6.4
Description
1050988
USB 4-wire cable—female to open-ended.
1051039
USB 4-wire cable—female to female.
100-Pin Connector
For details see Chapter 7: “100-Pin Connector”.
6.5
Scanner Connector
For details see Chapter 8: “Scanner Connector”.
60
Psion Teklogix WORKABOUT PRO HDK User Manual
7
100-PIN CONNECTOR
7.1 Overview. . . . . . . . . . . . . . . . . . . .
7.1.1 Signals On The 100-Pin Connector .
7.1.2 Connector Type . . . . . . . . . . .
7.1.3 Connector Position And Orientation
7.2 100-Pin Connector Pinout . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
63
63
63
64
64
7.3 Power And Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
7.4 Data And Address Buses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
7.5 Serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
7.6 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
7.7 General-Purpose I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
7.8 General-Purpose Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
7.9 PCMCIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
7.10 Wakeup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
7.11 I2C Device Identification. . . . . . . . . . . .
7.11.1 I2C Addresses . . . . . . . . . . . .
7.11.2 Expansion Module EEPROM Fields.
7.12 Example Expansion Modules . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
73
74
75
76
7.13 Psion Teklogix Serial Endcaps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
7.13.1 Serial Port Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
7.14 WORKABOUT PRO 2nd. Generation C, S USB Connector . . . . . . . . . . . . . . . . . . . . . 77
Psion Teklogix WORKABOUT PRO HDK User Manual
61
Chapter 7: 100-Pin Connector
Overview
7.1
Overview
This chapter describes the electrical resources that the WORKABOUT PRO can supply to the
expansion module connected to its 100-pin connector.
7.1.1
Signals On The 100-Pin Connector
An expansion module connects to the 100-pin connector. The WORKABOUT PRO provides
several groups of signals on this connector:
• DC power supply and ground.
• System data and address bus.
• Serial support.
• Connections to the WORKABOUT PRO USB host.
• Control signals.
These groups of signals are described in the following sections.
Note: Names listed here are those used by the WORKABOUT PRO. Signals may have other
names in expansion modules, scanner converter boards, or other devices.
Figure 7.1 The WORKABOUT PRO 100-Pin Connector Block Diagram
7.1.2
Connector Type
The 100-pin connector is an FX6-100S-0.8SV2 receptacle.
Psion Teklogix WORKABOUT PRO HDK User Manual
63
Chapter 7: 100-Pin Connector
Connector Position And Orientation
7.1.3
Connector Position And Orientation
Figure 7.2 WORKABOUT PRO Back View Showing The 100-pin Connector
100-pin connector
Standard placement of Pin 1
Placement of Pin 1 on
the WORKABOUT PRO
Battery compartment
7.2
100-Pin Connector Pinout
Pin names in the following table are those used on the WORKABOUT PRO.
Table 7.1 Pinout of the WORKABOUT PRO 100-Pin Connector
Pin
Name
Function
Active
State
During
Reset
State
During
Sleep
1
V_IN
Power
N/A
2
V_IN
Power
N/A
3
V_IN
Power
N/A
4
V_IN
Power
N/A
5
SD0
System data
bus
Input/output
Hi-Z
Low
6
SA0
System
address bus
Output
Low
Low
Abbreviations:
N/A= not applicable;
B = both high and low,
Hi-Z = high impedance.
64
Signal
Direction
Psion Teklogix WORKABOUT PRO HDK User Manual
Pull-up
value
(ohms)
Chapter 7: 100-Pin Connector
100-Pin Connector Pinout
Table 7.1 Pinout of the WORKABOUT PRO 100-Pin Connector (Continued)
Pin
Name
Function
Signal
Direction
Active
State
During
Reset
State
During
Sleep
7
SD1
System data
bus
Input/output
Hi-Z
Low
8
SA1
System
address bus
Output
Low
Low
9
SD2
System data
bus
Input/output
Hi-Z
Low
10
SA2
System
address bus
Output
Low
Low
11
SD3
System data
bus
Input/output
Hi-Z
Low
12
SA3
System
address bus
Output
Low
Low
13
SD4
System data
bus
Input/output
Hi-Z
Low
14
SA4
System
address bus
Output
Low
Low
15
SD5
System data
bus
Input/output
Hi-Z
Low
16
SA5
System
address bus
Output
Low
Low
17
SD6
System data
bus
Input/output
Hi-Z
Low
18
SA6
System
address bus
Output
Low
Low
19
SD7
System data
bus
Input/output
Hi-Z
Low
20
SA7
System
address bus
Output
Low
Low
21
GND
N/A
22
GND
N/A
23
SD8
System data
bus
Input/output
Hi-Z
Low
24
SA8
System
address bus
Output
Low
Low
25
SD9
System data
bus
Input/output
Hi-Z
Low
Pull-up
value
(ohms)
Abbreviations:
N/A= not applicable;
B = both high and low,
Hi-Z = high impedance.
Psion Teklogix WORKABOUT PRO HDK User Manual
65
Chapter 7: 100-Pin Connector
100-Pin Connector Pinout
Table 7.1 Pinout of the WORKABOUT PRO 100-Pin Connector (Continued)
Pin
Name
Function
Active
State
During
Reset
State
During
Sleep
26
SA9
System
address bus
Output
Low
Low
27
SD10
System data
bus
Input/output
Hi-Z
Low
28
SA10
System
address bus
Output
Low
Low
29
SD11
System data
bus
Input/output
Hi-Z
Low
30
SA11
System
address bus
Output
Low
Low
31
SD12
System data
bus
Input/output
Hi-Z
Low
32
SA12
System
address bus
Output
Low
Low
33
SD13
System data
bus
Input/output
Hi-Z
Low
34
SA13
System
address bus
Output
Low
Low
35
SD14
System data
bus
Input/output
Hi-Z
Low
36
SA14
System
address bus
Output
Low
Low
37
SD15
System
data bus
Input/output
Hi-Z
Low
38
SA15
System
address bus
Output
Low
Low
39
GND
N/A
40
GND
N/A
41
nSLOT_WAIT_SRC
PCMCIA
wait
Input
42
SA16
System
address bus
Output
43
nSLOT_IOIS16
PCMCIA
IOIS16
Input
44
SA17
System
address bus
Output
Abbreviations:
N/A= not applicable;
B = both high and low,
Hi-Z = high impedance.
66
Signal
Direction
Psion Teklogix WORKABOUT PRO HDK User Manual
Low
Pull-up
value
(ohms)
100 k
Low
Low
100 k1
None2
Low
Low
Low
Chapter 7: 100-Pin Connector
100-Pin Connector Pinout
Table 7.1 Pinout of the WORKABOUT PRO 100-Pin Connector (Continued)
Pin
Name
Function
Signal
Direction
Active
State
During
Reset
State
During
Sleep
Pull-up
value
(ohms)
45
nPREG
PCMCIA
REG
Output
Low
46
SA18
System
address bus
Output
47
nPOE
PCMCIA OE
Output
48
SA19
System
address bus
Output
49
nPWE
PCMCIA WE Output
50
SA20
System
address bus
Output
51
nPIOR
PCMCIA
IOR
Output
52
SA21
System
address bus
Output
53
nPIOW
PCMCIA
Output
54
SA22
System
address bus
Output
55
nSLOT_PSKTSEL
Socket select
Output
56
SA23
System
address bus
Output
57
GND
N/A
58
GND
N/A
59
nPCE1
PCMCIA
CE1
Output
60
SA24
System
address bus
Output
61
nPCE2
PCMCIA
CE2
Output
62
SA25
System
address bus
Output
63
InputPin63
PCMCIA slot
ready5
Input
High
100 k
64
InputPin64
GPIO
Input
Low
10 k
65
InputPin65
PCMCIA slot
card detect5
Input
Low
100 k
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
See note 4
Low
Low
Abbreviations:
N/A= not applicable;
B = both high and low,
Hi-Z = high impedance.
Psion Teklogix WORKABOUT PRO HDK User Manual
67
Chapter 7: 100-Pin Connector
100-Pin Connector Pinout
Table 7.1 Pinout of the WORKABOUT PRO 100-Pin Connector (Continued)
Pin
Name
Function
Active
66
InputPin66
GPIO
Input
Low
67
OutputPin67
PCMCIA slot
reset5
Output
High
68
RDY
Peripheral
ready
Input
69
OutputPin69
PCMCIA slot
power select5
70
State
During
Reset
State
During
Sleep
Pull-up
value
(ohms)
10 k
Float
Low
None
Output
Float
Hi-Z
None
OutputPin70
PCMCIA slot Output
power enable5
Float
Low
None
71
OutputPin71
GPIO
Output
Float
Hi-Z
None
72
OutputPin72
PCMCIA slot Output
buffer enable5
Float
High
None
73
InputPin73
GPIO
Input
74
OutputPin74
GPIO
Output
75
InputPin75
GPIO
Input
76
OutputPin76
GPIO
Output
77
GND
N/A
78
GND
N/A
79
nSLOT_WAKEUP
u-P GPI
Input
80
USB_H1_D+
USB host
port 1 D+
Input/output
81
FF_RXD
UART RXD
Input
82
USB_H1_D-
USB host
port 1 D-
Input/output
83
FF_TXD
UART TXD
Output
84
GND
85
FF_CTS
86
Not connected1
PWR_EN2
87
FF_DCD
UART DCD
Input
88
USB_H1_PSW
USB host
power enable
Output
N/A
100 k
Float
High
N/A
None
100 k
Float
See note None
3
B
100 k
N/A
100 k
N/A
High
N/A
UART CTS
Input
Low
100 k
Low
100 k
Input
Abbreviations:
N/A= not applicable;
B = both high and low,
Hi-Z = high impedance.
68
Signal
Direction
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 7: 100-Pin Connector
Power And Ground
Table 7.1 Pinout of the WORKABOUT PRO 100-Pin Connector (Continued)
Pin
Name
Signal
Direction
Function
Active
89
FF_DSR
UART DSR
Input
90
OutputPin90
GPIO
Output
91
FF_RI
UART RI
Input
92
OutputPin92
GPIO
Output
93
FF_DTR
UART DTR
Output
94
OutputPin94
GPIO
Output
95
FF_RTS
UART RTS
Output
96
InputPin96
GPIO
Input
97
DC_IN
DC power
Power
98
I2C_SDA
I2C data
Input/output
99
DC_IN
DC power
Power
100
I2C_SCL
I2C clock
Output
State
During
Reset
State
During
Sleep
Pull-up
value
(ohms)
Low
100 k
Low
100 k
Low
High
Low
High
100 k
N/A
4.7 k
N/A
4.7 k
Abbreviations:
N/A= not applicable;
B = both high and low,
Hi-Z = high impedance.
Note 1: Applies only to the WORKABOUT PRO M, C, S, and ME variants.
Note 2: Applies only to the WORKABOUT PRO 2nd. Generation C and S variants.
Note 3: Pin 76, OutputPin76 sleep state:
• WORKABOUT PRO C, S, M, ME—state maintained.
• WORKABOUT PRO 2nd. Generation C, S—high impedance.
Note 4: Pin 55, nSLOT_PSKTSEL active states:
• High—PCMCIA slot selected.
• Low—Compact flash slot selected.
Note 5: When a full PCMCIA interface is in use, these pins are not available for GPIO.
7.3
Power And Ground
Powering An Expansion Module
The power supply pins are:
• DC_IN (an external DC supply to the WORKABOUT PRO) (pins 97 and 99).
• V_IN (nominal 5 V DC supply to the expansion module) (pins 1, 2, 3, and 4).
• Ground (pins 21, 22, 39, 40, 57, 58, 77, 78, 84).
The DC_IN line can accept DC power of the following specification:.
Pin Name
DC_IN
Nominal Voltage
Tolerance
Maximum Ripple
5V
5%
50 mV
Maximum Current
2100 mA
Psion Teklogix WORKABOUT PRO HDK User Manual
69
Chapter 7: 100-Pin Connector
Data And Address Buses
V_IN conforms to the following specifications:
Pin Name
V_IN
Voltage Minimum
2.6 V
Voltage Maximum
5V
Maximum Current
2000 mA
Hardware connected to the 100-pin expansion slot can be powered from the WORKABOUT
PRO, using V_IN. Return is through the ground pins.
When the WORKABOUT PRO is on external power, the battery power is not used.
When the WORKABOUT PRO is powered by an external adaptor, V_IN is at the adaptor supply
voltage minus a diode drop. The adaptor supplies 4.5 V to 5.5 V. After the diode drop, V_IN is
3.8 V to 4.8 V.
When the WORKABOUT PRO is powered by the battery, V_IN is at the battery voltage, which
ranges from 2.6 V to 4.2 V (nominal 3.7 V).
For information on the battery power and the battery threshold voltages, see “Batteries” on
page 16.
Powering The WORKABOUT PRO Through The 100-pin Connector
The WORKABOUT PRO can be powered from the 100-pin expansion connector as well, using
the DC_IN pins (pins 97 and 99) as a power input. These pins are connected to the same line as the
DC_IN input from the external adaptor.
Warning: Do not reverse the polarity of power supplied to the DC_IN input on the 100-pin
connector. Such reversal will damage the WORKABOUT PRO.
7.4
Data And Address Buses
The system data and address buses include:
• Data bus (signals SD0-SD15).
• Address bus (signals SA0-SA25).
These signals are at CMOS levels (0 V to 3.3 V).
7.5
Serial
Serial expansion devices can be connected as modems through the following signals:
•
•
•
•
•
•
•
•
70
FF_RXD (data from the expansion device) (pin 81).
FF_TXD (data to the expansion device) (pin 83).
FF_CTS (Clear To Send flow-control signal from the expansion device) (pin 85).
FF_DCD (Data Carrier Detect flow-control signal from the expansion device) (pin 87).
FF_DSR (Data Set Ready flow-control signal from the expansion device) (pin 89).
FF_RI (Ring Indicator flow-control signal from the expansion device) (pin 91).
FF_DTR (Data Terminal Ready flow-control signal to the expansion device) (pin 93).
FF_RTS (Ready To Send flow-control signal to the expansion device) (pin 95).
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 7: 100-Pin Connector
USB
These signals originate from the full-function UART (FFUART) in the PXA255, and PXA270,
and are connected directly to the 100-pin connector. The signals are at CMOS levels (0 V to
3.3 V).
Table 7.2 Serial Ports
WORKABOUT PRO C, S, M, ME
WORKABOUT PRO 2nd. Generation C, S
Maximum baud rate 230 k baud.
921.6 k baud.
Enabling hardware
RTS/CTS
Requires a registry key setting. See “Registry
Settings For Serial Ports” on page 22.
For a complete list of the default COM port assignments, see “COM Port Assignments” on
page 24.
7.6
USB
The 100-pin connector provides the following signals from the WORKABOUT PRO USB host:
• USB_H1_D- (pin 82).
• USB_H1_D+ (pin 80).
• USB_H1_PSW (pin 88).
The WORKABOUT PRO 2nd. Generation USB host 1 port is also available on CN601. The
CN601 connector provides switched 5 V power controlled by USB_H1_PSW. See Figure 2.6 on
page 18 for the location of this connector.
Both full speed (12 megabits per second), and low speed (1.5 megabits per second), communication are supported.
The USB_H1_PSW signal can be used to control a power switch for the USB V+. The designer
must provide the appropriate +5 V power supply and the switch. USB_H1_PSW is managed by
software and can be controlled by the HDK software API.
These signals are at CMOS levels (0 V to 3.3 V).
7.7
General-Purpose I/O
A number of dedicated GPIO signals are provided.
These signals are pre-defined as outputs by Psion Teklogix:
• OutputPin71 (pin 71).
• OutputPin74 (pin 74).
• OutputPin76 (pin 76).
• OutputPin90 (pin 90).
• OutputPin92 (pin 92).
• OutputPin94 (pin 94).
These signals are pre-defined as inputs by Psion Teklogix:
• InputPin64 (pin 64).
• InputPin66 (pin 66).
• InputPin96 (pin 96).
The following PCMCIA signals can be used as GPIO outputs if the PCMCIA interface is not
being used:
Psion Teklogix WORKABOUT PRO HDK User Manual
71
Chapter 7: 100-Pin Connector
General-Purpose Interrupts
• OutputPin67 (pin 67).
• OutputPin69 (pin 69).
• OutputPin70 (pin 70).
• OutputPin72 (pin 72).
The following PCMCIA signals can be used as GPIO inputs if the PCMCIA interface is not
being used:
• InputPin63 (pin 63).
• InputPin65 (pin 65).
• InputPin73 (pin 73).
• InputPin75 (pin 75).
These signals are at CMOS levels (0 V to 3.3 V).
7.8
General-Purpose Interrupts
The following signals can be used as general-purpose interrupts if the PCMCIA interface is not
being used:
• InputPin63 (pin 63).
• InputPin65 (pin 65).
The active edge of these interrupts can be defined in software.
7.9
PCMCIA
The PCMCIA signals can be used as a standard PCMCIA interface. They can be also used to
connect memory devices or SRAM-like variable-latency I/O devices.
Signals provided to devices supporting the PCMCIA interface are as follows:
• Data bus (signals SD0 to SD15).
• Address bus (signals SA0 to SA25).
• nSLOT_WAIT_SRC (pin 41).
• nSLOT_IOIS16 (pin 43).
• nPREG (pin 45).
• nPOE (pin 47).
• nPWE (pin 49).
• nPIOR (pin 51)
• nPIOW (pin 53).
• nSLOT_PSKTSEL (pin 55).
• nPCE1 (pin 59).
• nPCE2 (pin 61).
• SLOT_READY (pin 63).
• nSLOT_CD (pin 65).
• SLOT_RST (pin 67).
• SLOT_3/5_SEL (pin 69).
• SLOT_PWR_EN (pin 70).
• nSLOT_BUF_EN (pin 72).
• nSLOT_VS1 (pin 73).
• nSLOT_BVD1 (pin 75).
All of these signals are at CMOS levels (0 V to 3.3 V).
The PCMCIA control signals are named according to the PXA255/PXA270 naming convention,
apart from the following:
Table 7.3 PCMCIA Control Signals That Do Not Follow The PXA255/PXA270 Naming Convention
PXA255/PXA270
Name
72
Name On WORKABOUT PRO
nPWAIT
nSLOT_WAIT_SRC
PSKTSEL
nSLOT_PSKTSEL
Psion Teklogix WORKABOUT PRO HDK User Manual
Notes
Low = Expansion PCMCIA interface enabled
Chapter 7: 100-Pin Connector
Wakeup
If the Psion Teklogix PCMCIA driver is used, all of the dual function pins (the general-purpose
I/O and interrupt signals) that can be used by the PCMCIA interface will be reserved by the
PCMCIA driver. All of these pins conform to the pin functions as defined by the PC Card Standard, Release 8.
A customized driver can be developed so that the dual function pins can be separated from the
PCMCIA interface. Psion Teklogix does not supply such a driver.
Memory devices and variable latency IO devices (such as ASICs and FPGAs) can be connected to
the PCMCIA interface. Timing of the interface is configurable. The nSLOT_WAIT_SRC signal
may used to extend the bus cycle.
The data bus, address bus, and control signals should be buffered in the expansion device to
prevent excessive loading. These traces should also be kept to the minimum possible length.
PCMCIA Interface Timing
The PCMCIA interface is fully compliant with the PCMCIA standard.
The PsionTeklogix::WORKABOUTPRO_HDK::PCMCIA namespace provides access to the
following registers so that the timing can be configured by a software application.
Table 7.4 PCMCIA Timing Control
Register
Memory Region Controlled
MCMEM1
Common memory
MCATT1
Attribute memory
MCIO1
I/O space
Table 7.5 Controlling PCMCIA Interface Timing
WORKABOUT PRO
API
7.10
PCMCIA::SetTiming()
WORKABOUT PRO 2nd. Generation
PCMCIA::SetTimingPXA27X()
Wakeup
A wakeup input is available so that expansion devices can signal the WORKABOUT PRO. This
pin is:
• nSLOT_WAKEUP (pin 79).
This signals is at CMOS levels (0 V to 3.3 V).
This signal wakes the WORKABOUT PRO from its suspend state—it does not generate an interrupt that can be detected by a software application. Connect the source to an expansion-slot
interrupt pin as well (InputPin63 or InputPin65), if an interrupt is also required.
7.11
I2C Device Identification
All expansion devices connected to the WORKABOUT PRO 100-pin expansion bus must contain
an I2C EEPROM. The expansion EEPROM is used to identify the hardware and to load appropriate drivers. This information is displayed on the Properties tab of the Control Panel
System program.
The 100-pin connector provides signals for an I2C bus:
•
I2C_SDA (pin 98).
Psion Teklogix WORKABOUT PRO HDK User Manual
73
Chapter 7: 100-Pin Connector
I2C Addresses
• I2C_SCL (pin 100).
These signals are at CMOS levels (0 V to 3.3 V).
This identifying EEPROM should be an I2C EEPROM of at least 128 bytes. Psion Teklogix recommends using a serial-access 1-kilobit (128 x 8) EEPROM, such as STMicroelectronics
ST24C01 or similar. Larger EEPROMs may be used. The address of the device must be set to
0x01 by connecting the A0 pin to the expansion module’s VCC and the A1 and A2 pins to ground.
An example of the circuit, as implemented on the sample Multi-I/O Expansion Module, is
shown below:
Figure 7.3 EEPROM Circuitry
In this circuit, to write protect the EEPROM use the jumper at SJ2 to connect the WP line to the
+3.3 V supply; to write enable the EEPROM use the jumper at SJ2 to connect the WP line
to ground.
See “I2C Device Identification” on page 73 for a description of the contents of this EEPROM.
Other I2C devices can also be connected to the I2C bus.
More information about the I2C bus can be found at:
http://www.nxp.com/products/interface_control/i2c/
7.11.1 I2C Addresses
I2C and smBus device addresses are 7 bits long.
The addresses defined here are shifted left by one bit to suit the device address format required by
the Windows CE I2C driver. The following addresses are reserved:
Address
74
Notes
WORKABOUT PRO 2nd. Generation C, S only
0x20
Power Micro
Yes
0x22
Power Micro
Yes
0x64
Real-time clock
0x66
Keyboard Micro
Yes
0x68
Keyboard Micro
Yes
0xa0
Psion Teklogix EEPROM address: E0,
E1, E2 low
0xa2
Expansion EEPROM address: E0 high,
E1, E2 low
0xe0
PXA255/270 configurable I2C address
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 7: 100-Pin Connector
Expansion Module EEPROM Fields
7.11.2 Expansion Module EEPROM Fields
The EEPROM has an internal address space of at least 128 bytes. Some of these bytes are predefined. Developers are free to use unused areas of the EEPROM for their own purposes.
Table 7.6 Fields Of The EEPROM In The Expansion-Module
Field
Address
(decimal)
Size
Contents
Manufacturing test
region
0-9
10 bytes
Reserved.
Revision
10
1 byte
ASCII ‘1’ (one).
Hardware revision
11
1 byte
ASCII ‘0’ - ‘9’, ‘A’ - ‘Z’, ‘a’ - ‘z’
Hardware type
12
1 byte
ASCII character.
Manufacturer/Model
13-32
20 bytes
ASCII text.
Zero-delimited if less than 20 bytes.
Character set is restricted to alpha-numeric
plus space.
Serial number
33-44
12 bytes
ASCII text.
Zero-delimited if less than 12 bytes.
Manufacturer-specific
45+
83+
Any.
Unused bytes are set to 0xFF. If a field is all 0xFF then Unknown is displayed for that field on the
Properties tab of the Control Panel System program.
Manufacturing test region
This is reserved for the original board manufacturer. The manufacturing test region is provided to
allow manufacturing test of the EEPROM. The contents are not used for any other purpose.
Revision
The version of the specification which defines the layout of the EEPROM and the contents of its
45 byte header. This value is specified by Psion Teklogix and is always set to 1.
Hardware revision
This is an ASCII character that defines the hardware revision. This field may be used by the driver
to vary the operation of the device. An OEM may set the contents to any value.
To view the contents of this field, in the Control Panel, click System, then click Properties.
Hardware type
This field contains a single ASCII character. It defines the hardware type of the expansion module.
Drivers for the hardware are loaded based on this value.
Psion Teklogix WORKABOUT PRO HDK User Manual
75
Chapter 7: 100-Pin Connector
Example Expansion Modules
Table 7.7 Hardware Type Characters In The Expansion Module EEPROM
ASCII
Character
Hardware Type
Code
PCMCIA
Serial
USB
The hardware supports a PCMCIA
socket. The PCMCIA
socket will be enabled
The hardware supports the serial port.
The serial FFUART
(COM1) driver will
be loaded.
The hardware supports the USB port.
The USB hub and USB
connection will
be powered.
a
0x61
Yes
b
0x62
c
0x63
d
0x64
Yes
e
0x65
Yes
f
0x66
g
0x67
Yes
s
0x73
See note.
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Any other value
Note: An ‘s’ or any undefined value means the hardware is standard, and the WORKABOUT PRO operating system will load drivers based on registry settings.
Manufacturer/Model
This field defines the expansion slot hardware.
If the expansion module requires a non-Psion Teklogix device driver, this field contains the name
of the device driver. The characters allowed in this field are restricted to those that are allowed in a
Windows registry key. For further information see “Registry Settings For Non-Psion Teklogix
Device Drivers” on page 23.
To view the contents of this field, in the Control Panel, click System, then click Properties.
Serial Number
This field contains the serial number of the expansion slot hardware.
To view the contents of this field, in the Control Panel, click System, then click Properties.
Manufacturer specific
This area is for the use by the manufacturer of the expansion card.
7.12
Example Expansion Modules
The HDK includes the following sample expansion modules:
•
•
76
PCMCIA Expansion Module which supports a slot for adding PCMCIA cards. See
Chapter 10: “Example: PCMCIA Expansion Module”for details.
Multi-I/O Expansion Module which provides separate connectors for the USB and serial ports
on both the 100-pin and scanner connectors. See Chapter 11: “Example: Multi-I/O Expansion
Module” for details.
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 7: 100-Pin Connector
Psion Teklogix Serial Endcaps
7.13
Psion Teklogix Serial Endcaps
Psion Teklogix supplies endcaps with serial ports for the WORKABOUT PRO and for the
WORKABOUT PRO 2nd. Generation computers. These are provided as field-installable kits. For
a list of available endcaps see www.PsionTeklogix.com/Accessories.
The endcap kit comprises the endcap, which includes an internal circuit board, an expansion
module which fits on the WORKABOUT PRO 100-pin expansion connector, and installation instructions. The two components are joined by a flex cable. The expansion module and internal
circuit board differ for each model of endcap.
The serial endcap has one or more of the following connectors:
•
•
•
IrDA infrared serial connection.
DE-9 female connector for TTL-level serial.
DE-9 male connector for RS-232 serial.
Figure 7.4 The Three-Port Serial Endcap (Model BR1000)
7.13.1 Serial Port Assignments
For details of the serial port assignments for these endcaps see “COM Port Assignments” on
page 24.
7.14
WORKABOUT PRO 2nd. Generation C, S USB Connector
All WORKABOUT PRO 2nd. Generation computers have an internal USB connector.
Psion Teklogix supplies a cable that connects to this socket. For information see the Accessories
catalog at www.PsionTeklogix.com/Accessories. This connector uses the same USB port as the
100-pin connector.
Table 7.8 Pinout Of The Internal USB Connector
Pin
Pin On
100-pin
Connector
1
Name
Description
Ground
2
80
USB_H1_D+
USB host port 1 D+
3
82
USB_H1_D-
USB host port 1 D-
4
88
USB_H1_PSW
USB host power enable
See Figure 2.6 on page 18 for the location of this connector.
Psion Teklogix WORKABOUT PRO HDK User Manual
77
Chapter 7: 100-Pin Connector
WORKABOUT PRO 2nd. Generation C, S USB Connector
Figure 7.5 Internal USB Connector Block Diagram
100-pin
connector
CN601
2
3
4
GND
USB_H1_D+
80
USB_H1_D+5 V
82
Switch
Enable
USB_H1_PSW
78
Psion Teklogix WORKABOUT PRO HDK User Manual
88
8
SCANNER CONNECTOR
8.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
8.2 Scanner Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
8.3 Scanner Connector Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
8.4 Scanner Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
8.5 The Scanner Flex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
8.6 Power And Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
8.7 Signals To The Scanner Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Psion Teklogix WORKABOUT PRO HDK User Manual
79
Chapter 8: Scanner Connector
Overview
8.1
Overview
This chapter describes the WORKABOUT PRO scanner connector and the devices that connect to
it. Other devices besides scanners can be connected through the scanner port. The term scanner
device applies to any hardware device that connects to the scanner port on the main logic board.
Figure 8.1 Scanner Connector Signals Block Diagram
Psion Teklogix provides scanners modules as either:
•
•
A scanner pod, or
A scanner endcap.
Scanner Pod
Scanners pods provided by Psion Teklogix have the following parts:
•
•
•
Scan engine.
Scanner converter board.
Trigger switch (on some models only).
Psion Teklogix WORKABOUT PRO HDK User Manual
81
Chapter 8: Scanner Connector
Scanner Kits
Figure 8.2 Scanner Pod Block Diagram
The scan engine is mounted on an appropriate backplate, which is then fastened to the WORKABOUT PRO.
Figure 8.3 The Scanner Pod In Place
Scanner Endcap
Scanner endcaps provided by Psion Teklogix have the following parts:
•
•
Scan engine.
Scanner converter board.
Scanner Converter Board
The scanner converter board interfaces the scan engine and the trigger switch to the
WORKABOUT PRO system. Different scan engines may require different converter boards.
The scanner module is connected to the WORKABOUT PRO scanner connector by the scanner
flex cable, using an interface defined by Psion Teklogix.
8.2
Scanner Kits
Psion Teklogix supplies several scanner kits. For a complete list see the Accessories Catalog at
www.PsionTeklogix.com/Accessories.
82
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 8: Scanner Connector
Scanner Connector Location
8.3
Scanner Connector Location
For the location of the scanner connector on the main logic board see “Connector Locations” on
page 17.
8.4
Scanner Connector Pinout
Table 8.1 Pinout Of The Scanner Connector
Pin
Name
Description
Direction
State
When
Active
State
During
Sleep
Pull-up Or
Pull-down
1
V+5_BAR
+5 V bar code
supply.
Switchable. 3
Power
N/A
Disabled
N/A
2
V+5_BAR
+5 V bar code
supply.
Switchable.3
Power
N/A
Disabled
N/A
3
IR_TXD1
BAR_TXD2
Data from WORKABOUT PRO to
scanner device.
Output
B
Low
None
4
USB_H2_D-
USB host port 2 D-.
Input/
output
B
Pulled
down
15 kΩ
5
IR_RXD1
BAR_RXD2
Data from scanner
device to WORKABOUT PRO.
Input
B
Pulled up
100 kΩ1
None2
6
USB_H2_D+
USB host port 2 D+.
Input/
output
B
Pulled
down
15 kΩ
7
nBAR_CTS1
BAR_CTS2
CTS from scanner
device to WORKABOUT PRO.
Input
L
Pulled up
100 kΩ1
10 kΩ2
8
GND
Ground.
Power
N/A
N/A
N/A
9
nBAR_RTS1
RTS from WORKABOUT PRO to
scanner device.
Output
L
Low
N/.A
BAR_RTS2
10
Not used1
BAR_3.3V 2
Switchable.2 3
Short circuit to
ground detection for
backward
compatibility.2
N/A
N/A
N/A
N/A
11
GND
Ground.
Power
N/A
N/A
N/A
Abbreviations:
N/A= not applicable
A= according to design requirements of driver and scanner device
B = both high and low
L= active low
H= active high
Hi-Z = high impedance
Psion Teklogix WORKABOUT PRO HDK User Manual
83
Chapter 8: Scanner Connector
Scanner Connector Pinout
Table 8.1 Pinout Of The Scanner Connector
Pin
Name
Description
Direction
State
When
Active
State
During
Sleep
Pull-up Or
Pull-down
12
GND
Ground.
Power
N/A
N/A
N/A
13
KB_SCAN_R71
KB_SCAN_R22
Keyboard row.
Input
N/A
Pulled
down
1 MΩ1
10 kΩ2
14
V+3.3
3.3 V power supply.
Not switchable.1
Switchable.2 3
Power
N/A
Enabled
N/A
15
KB_SCAN_C0A1
KB_SCAN_C72
Keyboard column.
Output
N/A
Driven
None
16
BAR_PWRDWN
Power-down from
scanner device to
WORKABOUT
PRO.
Input
H
Pulled up
100 kΩ1
10 kΩ2
17
BAR_TYPE
Not used.
Input
B
Pulled up
100 kΩ1
10 kΩ2
18
nBAR_WKUP
Wakeup signal to
scanner device.
Output
H
A
None1
100 kΩ2
19
Not used1
BAR_3.3V2
Switchable.2 3
Short circuit to
ground detection for
backward
compatibility.2
N/A
N/A
N/A
N/A
20
BAR_TRIG1
nBAR_TRIG2
Trigger signal to
scanner device.
Output
H
A
None
21
GND
Ground.
Power
N/A
N/A
N/A
22
GND
Ground.
Power
N/A
N/A
N/A
Abbreviations:
N/A= not applicable
A= according to design requirements of driver and scanner device
B = both high and low
L= active low
H= active high
Hi-Z = high impedance
Notes:
84
1:
Applies only to the WORKABOUT PRO M, C, S, and ME variants.
2:
Applies only to the WORKABOUT PRO 2nd. Generation C and S variants.
3:
When controlled through software, pins 1, 2, 10, 14, and 19 are switched on and off together.
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 8: Scanner Connector
The Scanner Flex
8.5
The Scanner Flex
The scanner connector accepts a flexible ribbon cable, which is supplied with the WORKABOUT
PRO. The WORKABOUT PRO is supplied with the scanner flex already attached to the main
logic board. The flex used with Psion Teklogix scanners has part number 1040017.
The scanner cable is inserted straight down into the connector on the main logic board, and folds
over to connect to the scanner device. The cable can be inserted in the scanner device when it is
pivoted away from the open back of the WORKABOUT PRO.
When the scanner device is in place, and the backplate is closed and fastened, the cable folds into
the space above the expansion module.
8.6
Power And Ground
The WORKABOUT PRO provides the following power and ground connections to the scanner
device:
•
•
•
Ground (pins 8, 11, 12, 21, 22).
V+5_BAR (pins 1 and 2).
V+3.3 (pin 14, also pins 10 and 19 for WORKABOUT PRO 2nd. Generation C, S).
WORKABOUT PRO C, S, M, ME
V+5_BAR is +5 V supplied from a DC-DC converter fed by V+5, the main 5 V supply of the
WORKABOUT PRO. It can be switched on and off by the BAR_PWR_EN signal while the
WORKABOUT PRO is running, but is disabled when the WORKABOUT PRO is suspended.
V+3.3 is the main 3.3 V system voltage of the WORKABOUT PRO, supplied ultimately from
V_IN via a DC-to-DC converter. V+3.3 remains powered when the WORKABOUT PRO
is suspended.
These voltages have the following specifications:
Table 8.2 Voltages Supplied To The Scanner Device
Supply
Nominal Voltage
Continuous Current
V+5_BAR
5V
300 mA
V+3.3
3.3 V
150 mA
V_IN is a diode OR of V_BAT (the DC voltage supplied by the WORKABOUT PRO battery),
and DC_IN (the DC power input from the external AC-to-DC adaptor). V_IN feeds a DC-to-DC
converter; the output of the converter is switched by the scanner power enable signal, and is
known as V+5_BAR.
When the terminal is powered by an external adaptor, V_IN is at the supply voltage of the adaptor
minus a diode drop. The adaptor supplies 4.5 V to 5.5 V; after the diode drop, V_IN is 3.8 V to
4.8 V.
When the terminal is powered by the battery, V_IN is at the battery voltage, which ranges from
2.6 V to 4.2 V (nominal 3.7 V).
For details of battery threshold voltages see “Batteries” on page 16.
Psion Teklogix WORKABOUT PRO HDK User Manual
85
Chapter 8: Scanner Connector
Signals To The Scanner Device
WORKABOUT PRO 2nd. Generation C, S
V+5_BAR is +5 V supplied from a DC-DC converter fed by V+5, the main 5 V supply of the
WORKABOUT PRO. It can be switched on and off by the 5VBAR_PWR_EN signal while the
WORKABOUT PRO is running, but is disabled when the WORKABOUT PRO is suspended.
V+3.3 is the main 3.3 V system voltage of the WORKABOUT PRO, supplied ultimately from
VIN via a DC-to-DC converter. V+3.3 remains powered when the WORKABOUT PRO
is suspended. In the WORKABOUT PRO 2nd. Generation, the 3.3V supply to the scanner connector is disabled when the WORKABOUT PRO is suspended.
These voltages have the following specifications:
Table 8.3 Voltages Supplied To The Scanner Device
Supply
Nominal Voltage
Continuous Current
V+5_BAR
5V
300 mA
V+3.3
3.3 V
1A
VIN is a diode OR of VBAT (the DC voltage supplied by the WORKABOUT PRO battery), and
DC_IN (the DC power input from the external AC-to-DC adaptor). VIN feeds a DC-to-DC converter; the output of the converter is switched by the scanner power enable signal, and is known as
V+5_BAR.
When the terminal is powered by an external adaptor, VIN is at the supply voltage of the adaptor
minus a diode drop. The adaptor supplies 4.5 V to 5.5 V; after the diode drop, VIN is 3.8 V to
4.8 V.
When the terminal is powered by the battery, VIN is at the battery voltage, which ranges from
2.6 V to 4.2 V (nominal 3.7 V).
For details of battery threshold voltages see “Batteries” on page 16.
8.7
Signals To The Scanner Device
The WORKABOUT PRO does not provide the data and address buses of its main processor (the
PXA255 or PXA270) to the scanner port. Instead, communication to the scanner is provided by
USB or serial lines.
All the serial signals are present to connect a decoded scanner. A USB host port is also provided so
that USB peripherals can be connected via the scanner port.
These signals are at 3.3 V CMOS levels.
Serial scanner devices can be connected through the following signals on the
WORKABOUT PRO:
• IR_TXD (data to the scanner device, pin 3).
• IR_RXD (data from the scanner device, pin 5).
• nBAR_CTS (Clear To Send flow-control signal from the scanner device, pin 7).
• nBAR_RTS (Ready To Send flow-control signal to the scanner device, pin 9).
Serial scanner devices can be connected through the following signals on the WORKABOUT
PRO 2nd. Generation:
•
•
86
BAR_TXD (data to the scanner device, pin 3).
BAR_RXD (data from the scanner device, pin 5).
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 8: Scanner Connector
Signals To The Scanner Device
• BAR_CTS (Clear To Send flow-control signal from the scanner device, pin 7).
• BAR_RTS (Ready To Send flow-control signal to the scanner device, pin 9).
The assignment for this port is COM 3. It cannot be reassigned.
USB scanner devices can communicate through the following bidirectional data signals:
•
•
USB_H2_D+ (pin 6).
USB_H2_D- (pin 4).
Note: There is no USB power-enable signal on the scanner port.
In the WORKABOUT PRO 2nd. Generation, the 5V supply (V+5_BAR) is controlled
by 5VBAR_PWR_EN.
In addition, there are control signals for both USB and serial scanner devices:
• BAR_PWRDWN (pin 16).
• nBAR_WKUP (pin 18).
• nBAR_TRIG (pin 20).
BAR_PWRDWN is an input to the main logic board. The scanner device can use this signal to
inform the WORKABOUT PRO that it has shut down. Pull this signal high to enable it.
nBAR_WKUP and nBAR_TRIG are outputs from the main logic board. Their operation varies
depending on the design of the scanner device and the device driver.
A pair of lines from the WORKABOUT PRO keyboard matrix are also provided:
• Input on pin 13.
• Output on pin 15.
Short these signals together for a minimum of 20 milliseconds to initiate a scan or to wake up the
WORKABOUT PRO.
Note: nBAR_CTS and nBAR_RTS —BAR_CTS and BAR_RTS on the WORKABOUT PRO 2nd.
Generation—are not hardware flow-control signals. CTS must be polled by software, and
RTS has to be set / cleared by software.
Apart from V+5_BAR, the signals connected to the scanner port are at 3.3 V CMOS levels. Use a level translator before the scanner cable to connect 5 V signals to the
WORKABOUT PRO main logic board.
Psion Teklogix WORKABOUT PRO HDK User Manual
87
9
EXAMPLE: SCANNER CONVERTER BOARD
9.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
9.2 Example Scanner Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
9.2.1 Serial Scanner Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
9.3 Power And Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
9.4 Signals To The Scanner Module.
9.4.1 Serial Signals . . . . .
9.4.2 USB Signals . . . . . .
9.4.3 Control Signals . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Psion Teklogix WORKABOUT PRO HDK User Manual
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
96
96
97
97
89
Chapter 9: Example: Scanner Converter Board
Overview
9.1
Overview
Psion Teklogix provides a scanner converter board in WORKABOUT PRO units that incorporate
a scanner. This board is attached to the scan engine, and differs depending on the installed scanner.
At a minimum, the scanner board physically connects the supply voltages and signal lines provided by the scanner flex to the scanner device. Different scanner devices require different
regulation and switching.
This chapter describes the scanner converter board used with the SE1223 scanner, and its interface
to the WORKABOUT PRO main logic board.
9.2
Example Scanner Boards
The schematics for two sample scanner boards are included in the HDK. Both boards work with
the SE1223 scan engine. One provides serial output: The other provides USB output. These
boards work with both the WORKABOUT PRO and the WORKABOUT PRO 2nd.
Generation computers.
9.2.1
Serial Scanner Board
This board can be configured for use either with Symbol scan engines, or with Intermec
scan engines.
This scanner board incorporates AND-gate buffers on the signal lines: a 74HCT08 buffers
outbound signals, and a 74LVC08 buffers inbound signals.
The scanner board can be configured for the Symbol or Intermec scan engines by providing
zero-ohm resistors (jumpers) in locations according to the following table:
Table 9.1 Configuration Resistors
Connects
When
Jumpered
Provided For
Symbol
Scan Engines
Name
Provided For
Intermec
Scan Engines
R10
HOST_TRIG to Symbol_TRIG
R11
HOST_TRIG to Inter_TRIG
x
R12
HOST_WKUP to Inter_PWREn
x
R13
HOST_WKUP to Symbol_WKUP
x
R14
RTS to Symbol_CTS
x
R15
RTS to Inter_CTS
x
R16
CTS to Inter_RTS_Symbol_CTS
x
R17
CTS to Symbol_RTS
R18
TXD to Inter_RXD
R19
TXD to Symbol_RXD_Inter_PWREn
x
R20
Connects V+5 to JP1 pin 5
(Inter_Symbol_TXD)
x
R21
Connects JP1 pin 8 and JP1 pin 11
x
x
x
Note: x = zero-ohm resistor (jumper) present
Psion Teklogix WORKABOUT PRO HDK User Manual
91
Chapter 9: Example: Scanner Converter Board
Serial Scanner Board
Table 9.1 Configuration Resistors (Continued)
Connects
When
Jumpered
Provided For
Symbol
Scan Engines
Name
Provided For
Intermec
Scan Engines
PR1
V+5 to JP1 pin 2 (Inter_RXD)
x
PR2
V+5 to JP1 pin 1
x
GR1
Gnd to JP1 pin 12 (Symbol_TRIG)
x
GR2
Gnd to JP1 pin 7 (Symbol_RTS)
x
GR3
Gnd to JP1 pin 3 (Inter_Trigger)
x
Note: x = zero-ohm resistor (jumper) present
The default configuration is for Symbol scan engines. The schematic is drawn this way.
This scanner converter board has three connectors:
•
•
•
Host scanner connector.
Scan engine connector.
Trigger switch connector.
Host Scanner Connector
JP2 is a 22-pin connector that accepts the 22-pin flex cable from the WORKABOUT PRO main
logic board. This connector has the following pins:
Table 9.2 Pinout Of Host Scanner Connector (JP2)
Pin
Name On
WORKABOUT PRO
Name On
Converter
Board
Description Direction
State
During Pull-up Or
Device Pull-down
Sleep
1
V+5_BAR
V+5
+5 V bar
code
supply
Power
N/A
Disabled N/A
2
V+5_BAR
V+5
+5 V bar
code
supply
Power
N/A
Disabled N/A
3
IR_TXD
TXD
Data from
WORKABOUT
PRO to
scanner
device
Output
B
Abbreviations:
N/A= not applicable;
A=- according to design requirements of driver and scanner device,
B = both high and low,
L= active low,
H= active high.
92
Active
State
Psion Teklogix WORKABOUT PRO HDK User Manual
None
Chapter 9: Example: Scanner Converter Board
Serial Scanner Board
Table 9.2 Pinout Of Host Scanner Connector (JP2) (Continued)
Pin
Name On
WORKABOUT PRO
Name On
Converter
Board
Description Direction
Active
State
State
During Pull-up Or
Device Pull-down
Sleep
4
USB_H2_D-
(Not
connected.)
USB host
port 2 D-
Input/
outputl
B
Pulled
down
15 kΩ
5
IR_RXD
RXD
Data from
scanner
device to
WORKABOUT
PRO
Input
B
Pulled
up
100 kΩ
6
USB_H2_D+
(Not
connected.)
USB host
port 2 D+
Input/
outputl
B
Pulled
down
15 kΩ
7
nBAR_CTS
CTS
CTS from
scanner to
WORKABOUT
PRO
Input
L
Pulled
up
100 kΩ
8
GND
(Connected to
ground.)
Ground
Power
N/A
N/A
N/A
9
nBAR_RTS
RTS
RTS from
WORKABOUT
PRO to
scanner.
Output
L
Low
N/A
10
N/C
(Connected to
ground.)
Do not
connect.
N/A
N/A
N/A
N/A
11
GND
(Connected to
ground.)
Ground.
Power
N/A
N/A
N/A
12
GND
(Connected to
ground.)
Ground.
Power
N/A
N/A
N/A
13
KB_SCAN_R7
KB_SCAN_R7
Keyboard
row 7
Input
N/A
Pulled
down
1 MΩ
14
V+3.3
V+3.3
3.3V
Power
supply.
Power
N/A
Enabled
N/A
15
KB_SCAN_COA
KB_SCAN_CO Keyboard
A
column 0.
Output
N/A
Driven
None
Abbreviations:
N/A= not applicable;
A=- according to design requirements of driver and scanner device,
B = both high and low,
L= active low,
H= active high.
Psion Teklogix WORKABOUT PRO HDK User Manual
93
Chapter 9: Example: Scanner Converter Board
Serial Scanner Board
Table 9.2 Pinout Of Host Scanner Connector (JP2) (Continued)
Pin
Name On
WORKABOUT PRO
Name On
Converter
Board
Description Direction
Active
State
State
During Pull-up Or
Device Pull-down
Sleep
16
BAR_PWRWDWN
HOST_PWRD
WN
Powerdown from
scanner
device to
WORKABOUT
PRO.
Input
H
Pulled
up
100 kΩ
17
BAR_TYPE
BAR_TYPE
Not used.
Input
B
Pulled
up
100 kΩ
18
BAR_WKUP
HOST_WKUP
Wakeup
signal to
scanner
device.
Output
A
Low
None
19
N/C
(Connected to
ground.)
N/A
N/A
N/A
N/A
20
BAR_TRIG
HOST_TRIG
Trigger
signal to
scanner
device
Output
A
Low
None
21
GND
(Connected to
ground.)
Ground
Power
N/A
N/A
N/A
22
GND
(Connected to
ground.)
Ground
Power
N/A
N/A
N/A
Abbreviations:
N/A= not applicable;
A=- according to design requirements of driver and scanner device,
B = both high and low,
L= active low,
H= active high.
Scan Engine Connector
JP1 is a 12-pin connector that accepts a cable that connects to the scan engine itself. This connector has different pinouts depending on whether the converter board is configured for Symbol, or
Intermec, scan engines.
Table 9.3 Pinout Of Scan Engine Connector JP1 (Configured For Symbol)
Pin
Name On Converter Board
Description
1
V+5_BAR
+5V supply to scan engine
Power
2
V+5_BAR
+5V supply to scan engine
Power
3
GND
Ground
Power
Note: “Input” and “output” are relative to the WORKABOUT PRO main logic board.
94
Direction
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 9: Example: Scanner Converter Board
Serial Scanner Board
Table 9.3 Pinout Of Scan Engine Connector JP1 (Configured For Symbol) (Continued)
Pin
Name On Converter Board
Description
Direction
4
Symbol_RXD_Inter_PWREn
Data from scan engine to
WORKABOUT PRO.
Input
5
Inter_Symbol_TXD
Data from WORKABOUT PRO to
scan engine.
Output
6
Inter_RTS_Symbol_CTS
CTS from scan engine to WORKABOUT PRO Input
7
Symbol_RTS
RTS from WORKABOUT PRO to
scan engine.
Output
8
Symbol_PWRDWN
Power-down signal from scan engine to
WORKABOUT PRO.
Input
9
NC
Not connected.
10
Symbol_CTS
CTS from scan engine to WORKABOUT PRO Input
11
Symbol_WKUP
Wakeup signal to scan engine.
Output
12
Symbol_TRIG
Trigger signal to scan engine.
Output
Note: “Input” and “output” are relative to the WORKABOUT PRO main logic board.
Table 9.4 Pinout Of Scan Engine Connector JP1 (Configured For Intermec)
Pin
Name On Converter Board
Description
Direction
1
V+5_BAR
+5V supply to scan engine
Power
2
Inter_RXD
Data from scan engine to
WORKABOUT PRO.
Input
3
Inter_Trigger
Trigger signal to scan engine.
Output
4
Symbol_RXD_Inter_PWREn
Wakeup signal to scan engine.
Output
5
Inter_Symbol_TXD
Data from WORKABOUT PRO to
scan engine.
Output
6
Inter_RTS_Symbol_CTS
RTS from WORKABOUT PRO to
scanner module
Output
7
GND
Ground
Power
8
Symbol_PWRDWN
Power-down signal from scan engine to
WORKABOUT PRO. Connected to pin 11.
Input
9
NC
Not connected.
10
Inter_CTS
CTS from scan engine to
WORKABOUT PRO
Input
11
Symbol_PWRDWN
Power-down signal from scan engine to
WORKABOUT PRO. Connected to pin 8.
Input
12
GND
Ground
Power
Note: “Input” and “output” are relative to the WORKABOUT PRO main logic board.
Psion Teklogix WORKABOUT PRO HDK User Manual
95
Chapter 9: Example: Scanner Converter Board
Power And Ground
Trigger Switch Connector
CN3 is a three-pin header that allows connection to the trigger-switch lines fed from the
WORKABOUT PRO’s keyboard matrix.
9.3
Power And Ground
The WORKABOUT PRO provides the following power and ground connections to JP2 on the
scanner board:
•
•
Ground (pins 8, 11, 12, 21, 22 on the scanner flex).
V+5_BAR (pin 1 and 2).
This voltage is +5 V from a DC-DC converter fed by V_+5, the WORKABOUT PRO main
5 V supply. It is switched by the scanner power-enable signal BAR_PWR_EN.
• V+3.3 (pin 14):
+3.3 V from the WORKABOUT PRO internal DC-to-DC converter.
These voltages have the following specifications:
Table 9.5 Supply Voltages For The Scanner
Supply
Nominal Voltage
Continuous Current
Peak Current
Max Peak Duration
V+5_BAR
5V
300 mA
500 mA
100 mS
V+3.3
3.3 V
150 mA
1000 mA
N/A
The voltage VIN is fed by a diode OR of V_BAT (the DC voltage supplied by the WORKABOUT
PRO battery), and DC_IN, the DC power input to the terminal. VIN feeds a DC-to-DC converter;
the output of the converter is switched by PWR_EN and is known as V+5_BAR.
V+5_BAR is maintained by the DC-to-DC converter at 5V. V+5_BAR can be switched on and off
by software while the WORKABOUT PRO is running, but it is disabled when it is suspended.
V+3.3 remains powered when the WORKABOUT PRO is suspended.
On this scanner board, V+5_BAR controls an Atmel AAT4250 switch to switch V+3.3 to the
scanner module itself. The switched 3.3 V power is V+3.3_BAR.
9.4
Signals To The Scanner Module
The WORKABOUT PRO does not provide the data and address buses of its main processor (the
PXA255) to the scanner port. Instead, communication to the scanner is provided by USB or serial
lines. All the serial signals are present to connect a decoded scanner. A USB host port is also
proved so that USB peripherals can be connected via the scanner port.
9.4.1
Serial Signals
This scanner board is configured to use serial communications with the Symbol SE1223 scanner
series. When the scanner board is configured to use serial communication, the scanner uses the
following signals from JP2, the 22-pin scanner flex that connects to the WORKABOUT PRO:
•
•
•
•
96
IR_TXD (data to the scanner device, pin 3 on JP2).
IR_RXD (data from the scanner device, pin 5).
nBAR_CTS (Clear To Send flow-control signal from the scanner device, pin 7).
nBAR_RTS (Ready To Send flow-control signal to the scanner device, pin 9).
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 9: Example: Scanner Converter Board
USB Signals
These signals are buffered through U1, a 74LVC244A octal buffer. The buffered signals connected
to the scanner itself (through the 12-pin JP1) are, in the same order:
•
•
•
•
BAR_TXD (data to the scanner device, pin 5 on JP1).
BAR_RXD (data from the scanner device, pin 4).
BAR_CTS (Clear To Send flow-control signal from the scanner module, pin 6).
BAR_RTS (Ready To Send flow-control signal to the scanner device, pin 7).
Note: nBAR_CTS and nBAR_RTS are not hardware flow-control signals, CTS must be polled by
software, and RTS has to be set / cleared by software.
Apart from V+5_BAR, the signals connected to the scanner port are 3.3 V CMOS. Use a
level translator before the scanner cable to connect 5 V signals to the WORKABOUT
PRO main PCB.
9.4.2
USB Signals
When the scanner board is configured to use USB communication, the scanner uses the following
signals from JP2, the 22-pin scanner flex that connects to the WORKABOUT PRO:
• USB_H2_D+ (pin 6 on JP2).
• USB_H2_D- (pin 4).
These signals are buffered through U1, and use the following pins on JP1, in the same order:
•
•
Pin 6.
Pin 4.
Note: The WORKABOUT PRO does not provide a USB power-enable signal to the
scanner board.
9.4.3
Control Signals
There are control signals used for both USB and serial scanner devices:
• BAR_PWRDWN (pin 16 on JP2).
• BAR_WKUP (pin 18).
• BAR_TRIG (pin 20).
BAR_PWRDWN is an input to the main logic board. The scanner can use this signal to inform the
WORKABOUT PRO that it has shut down.
BAR_WKUP is an output from the main logic board. This signal is buffered through U1 and is
provided to the scanner module as BAR_WKUP.
BAR_TRIG is an output from the main logic board. This signal is buffered through U1 and is provided to the scanner module as BAR_TRIG.
The operation of these signals is dependent on the driver controlling them.
A pair of lines from the WORKABOUT PRO keyboard matrix are also provided through JP2:
• KB_SCAN_R7 (an input, pin 13 on JP2)
• KB_SCAN_C0A (an output, pin 15)
These signals can be shorted together for a minimum of 20 milliseconds to initiate a scan or wake
up the terminal. On the scanner board, these signals are connected directly to CN3.
Psion Teklogix WORKABOUT PRO HDK User Manual
97
10
EXAMPLE: PCMCIA EXPANSION MODULE
10.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
10.2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
10.3 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
10.4 Expansion Module Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
10.5 Electrical . . . . . . . . . . . . . . . . .
10.5.1 PCMCIA Compatibility . . . .
10.5.2 The Card Detect Signals . . . .
10.5.3 The Buffer Enable Signals . . .
10.5.4 The Slot Power Enable Signal .
10.5.5 Selectable Card Supply Voltage
10.6 EEPROM Data . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Psion Teklogix WORKABOUT PRO HDK User Manual
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.102
.102
.103
.103
.103
.103
.104
99
Chapter 10: Example: PCMCIA Expansion Module
Overview
10.1
Overview
This chapter describes a PCMCIA Expansion Module available for the WORKABOUT
PRO—part number 1030248, model WA9001. The instructions in this chapter build on the information in Chapter 4: “Mechanical Considerations” and Chapter 7: “100-Pin Connector”.
The PCMCIA expansion module allows the user to connect a Type I or Type II PCMCIA card to
the WORKABOUT PRO. The expansion module accepts 3.3 V and 5 V PCMCIA cards.
The card must fit within the enclosure of the WORKABOUT PRO when the endcap and card stop
are installed, although a custom endcap can be created for extended PCMCIA cards.
This expansion module plugs into the WORKABOUT PRO 100-pin expansion connector.
The PCMCIA expansion module is available as a kit. The kit includes the following items:
• PCMCIA adaptor board (part number 1030313).
• Mechanical stop for the PCMCIA card (part number 1030224).
• Eight M2 x 4 screws (part number 9001906).
• Installation instructions (part number 8000037).
A metal frame for mounting the expansion module is already provided in the WORKABOUT
PRO. It also serves as a guide for the PCMCIA card.
10.2
Installation
To install the PCMCIA Adaptor Expansion Module:
1. Install the expansion module as shown in “Expansion Module Installation” on page 34.
2. Remove the WORKABOUT PRO end-cap.
Note: This sample PCMCIA Expansion Module does not use the mounting frame screw holes.
Instead, it is attached along its lower edge using the screws that hold the mounting frame
in place. These screws must be removed in order to position the expansion module, and
replaced once it is positioned.
To insert a PCMCIA card, slide it in through the end of the WORKABOUT PRO. When the
PCMCIA card is inserted, it is restrained by a plastic card stop. This card stop is fastened to the
body of the WORKABOUT PRO by four M2 x 4 screws. The endcap fits over the top of the
card stop.
10.3
Dimensions
An IGES model of the PCMCIA expansion model is in
...\Mechanical\WORKABOUTPRO\iges_files\pcmcia_xmod.igs. In this model the lower
screw holes are positioned so that the module attaches to the mounting frame using the mounting
frame screws. Unless you want to attach your expansion module in this way, use the IGES model
of the mounting frame to determine the screw locations.
10.4
Expansion Module Connectors
The expansion module connects to the WORKABOUT PRO 100-pin connector. It also has an
unkeyed PCMCIA connector.
The PCMCIA connector is aligned parallel to the expansion board, on the opposite side to the
100-pin connector.
Psion Teklogix WORKABOUT PRO HDK User Manual
101
Chapter 10: Example: PCMCIA Expansion Module
Electrical
When installed inside the WORKABOUT PRO, the PCMCIA Expansion Module can accept
PCMCIA Type I and Type II cards. The cards are secured by the PCMCIA card stop. Extended
Type I and Type II cards can be accommodated if the WORKABOUT PRO endcap and card stop
are removed.
10.5
Electrical
The schematics for this PCMCIA expansion module are in
...\Electrical\WORKABOUTPRO\Samples\PCMCIAExpansionCard.pdf.
Figure 10.1 The PCMCIA Expansion Module Block Diagram
The PCMCIA Expansion Module serves as a PCMCIA host bus adaptor for the WORKABOUT
PRO, buffering the system data and address buses from the 100-pin connector to the
PCMCIA connector.
The expansion module incorporates a Psion Teklogix-standard serial EEPROM for identification
to the WORKABOUT PRO system.
10.5.1 PCMCIA Compatibility
The PCMCIA Expansion Module implements a subset of the PCMCIA standard. Depending on
driver support in the WORKABOUT PRO, it can handle the following PCMCIA Card interfaces:
• Memory
• Memory or I/O
The Expansion Module can supply a maximum of 750 mA to the PCMCIA card through
the VCC pins.
102
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 10: Example: PCMCIA Expansion Module
The Card Detect Signals
The handling of some other signals is described in the following sections which use the signal
names on the schematic of the Expansion Module, referencing pin names at the connectors only
when necessary.
10.5.2 The Card Detect Signals
The two Card Detect signals from the PCMCIA connector (nPC_CD1 and nPC_CD2, active low)
are pulled low when a card is inserted. On the expansion card, they are ORed through buffer U208
to become the nSLOT_CD signal (active low). This signal goes to the 100-pin connector, and it is
also used elsewhere in the module.
10.5.3 The Buffer Enable Signals
The nSLOT_CD signal is ORed with nSLOT_PSKTSEL and nSLOT_BUF_EN (active-low and
from the 100-pin connector) to create the nSLOT_BUF_OE signal. This signal, active low,
enables the data-bus, control-bus, and address-bus buffers on the expansion module.
The data-bus buffer, U201, is bidirectional. The signal nCARD_D_DIR (active low) specifies
which direction U201 will forward data.
10.5.4 The Slot Power Enable Signal
The SLOT_PWR_EN signal from the 100-pin connector (active high) is ANDed with a number of
other signals as they cross the Expansion Module.
The nPC_VS1, nPC_BVD1 signals from the PCMCIA connector, active low, become
nSLOT_VS1 and nSLOT_BVD1 respectively at the 100-pin connector. The PC_READY signal
from the PCMCIA connector, active high, becomes the SLOT_READY signal at the
100-pin connector
The SLOT_RST signal from the 100-pin connector, active high, becomes the PC_RST signal at
the PCMCIA connector.
All of these signals require the SLOT_PWR_EN signal to be asserted (high) before they
are forwarded.
10.5.5 Selectable Card Supply Voltage
The supply voltage for the PCMCIA card is selectable (3.3 V or 5 V) through the
SLOT_PWR_SEL and SLOT_5V_EN signals from the 100-pin connector.
The SLOT_PWR_SEL signal, when active (high), enables the supply voltage to the
PCMCIA card.
When asserted (high), the SLOT_5V_EN signal switches the 5 V output of U301 to the
V+3.3/V+5 line. When SLOT_5V_EN is low, the 3.3 V module supply voltage from U303 is
switched to the V+3.3/V+5 line.
The V+3.3/V+5 line provides the PCMCIA card supply voltage, VCC, on pins 17 and 51 of the
PCMCIA connector. It also serves to pull the PC_READY, nPC_BVD1, nPC_VS1,
nPC_WAIT_SRC, and nPC_IOIS16 lines high, maintaining compatibility between these signals
and the PCMCIA card.
Psion Teklogix WORKABOUT PRO HDK User Manual
103
Chapter 10: Example: PCMCIA Expansion Module
EEPROM Data
10.6
EEPROM Data
The EEPROM fields are described in “Expansion Module EEPROM Fields” on page 75. In the
PCMCIA Expansion Module they are programmed as follows:
Table 10.1 EEPROM Contents Of PCMCIA Adaptor Expansion Module
EEPROM Field
104
Address
Size
Contents
1) Manufacturing test
region
0-9
10 bytes
2) Revision
10
1 byte
ASCII ‘1’ (0x31)
3) Hardware revision
11
1 byte
ASCII ‘0’ (0x30) for revision ES0,
ASCII ‘1’ (0x31) for revision ES1
4) Hardware type
12
1 byte
ASCII ‘a’ (0x61)
5) Manufacturer/Model
13-32
20 bytes
ASCII text ‘PsionTeklogix PCMCIA’:
.0x50, 0x73, 0x69, 0x6f, 0x6e, 0x54, 0x65, 0x6b,
0x6c, 0x6f, 0x67, 0x69, 0x78, 0x20 0x50, 0x43,
0x4d, 0x43, 0x49, 0x41
6) Serial number
33-44
12 bytes
ASCII text, as appropriate.
Example: ‘1234’ is 0x31, 0x32, 0x33, 0x34, 0x00.
The remaining locations are not programmed, and
contain 0xff
7) Manufacturer-specific
45+
83+
All 0xff
Psion Teklogix WORKABOUT PRO HDK User Manual
EXAMPLE: MULTI-I/O EXPANSION MODULE
11
11.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
11.2 Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
11.3 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3.1 Main Logic Board 100-Pin Connector (J1) . . . .
11.3.2 Main Logic Board Scanner Connector (J2) . . . .
11.3.3 Scanner-Port Serial Connector (J3). . . . . . . . .
11.3.4 USB Host Port 2 Connector (J4) . . . . . . . . . .
11.3.5 The FF UART Serial Connector (J5). . . . . . . .
11.3.6 The USB Host 1 Connector (J6) . . . . . . . . . .
11.3.7 The Power Connector (J7) . . . . . . . . . . . . .
11.4 Configuration . . . . . . . . . . . . . . . . . . . . . . . . .
11.4.1 Slot Power Control . . . . . . . . . . . . . . . . .
11.4.2 EEPROM Write Control . . . . . . . . . . . . . .
11.4.4 Voltage Configuration For High-Power Output . .
11.4.3 Voltage Configuration For Standard-Power Output
11.4.5 Control Signals For FFUART Level Converter . .
11.4.6 TTL Output Option For Scanner Serial Port . . . .
11.5 Power And Ground . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.108
.109
.109
.109
.110
.110
.112
.113
.113
.114
.114
.116
.115
.117
.118
.118
11.6 EEPROM Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
11.7 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Psion Teklogix WORKABOUT PRO HDK User Manual
105
Chapter 11: Example: Multi-I/O Expansion Module
Overview
11.1
Overview
This chapter describes the Multi-I/O Expansion Module for the WORKABOUT PRO. This
product is no longer supplied by Psion Teklogix. These instructions are intended to give you guidance in the design and implemention of an expansion module for the WORKABOUT PRO. They
build on the information in Chapter 4: “Mechanical Considerations”, Chapter 7: “100-Pin Connector”, and Chapter 8: “Scanner Connector”.
Figure 11.1 Multi I/O Expansion Module Block Diagram
The Multi-I/O Expansion Module fits inside the WORKABOUT PRO and is designed to connect
to the 100-pin connector, and optionally to the scanner connector, of the WORKABOUT PRO. It
allows easy access (through low profile SMT MOLEX connectors): to the WORKABOUT PRO
full-function UART (FFUART) at TTL or RS-232 level; to the scanner port UART (at RS-232
level); and to two USB host connections.
The Multi-I/O Expansion Module can provide power to the devices connected to it. Two options
are available, one to supply 5 V, and one to supply 3.3 V. The standard current supply is limited to
100 mA, whereas the high-current power option provides a 4 A at 5 V. This supply can be
software controlled.
Psion Teklogix WORKABOUT PRO HDK User Manual
107
Chapter 11: Example: Multi-I/O Expansion Module
Schematics
Features of the Multi-I/O Expansion Module include:
•
Interface to the WORKABOUT PRO 100-pin connector:
- FFUART serial connections.
- 3 General-Purpose I/O signals.
- +VIN DC supply.
•
Interface to the WORKABOUT PRO scanner connector:
- Scanner serial connections.
- USB host 2 connections.
- 3.3 V and 5 V for the scanner device.
•
•
Conversion of the serial data and control lines for the FFUART and the scanner UART from
CMOS levels to RS-232 levels. The conversion for the FFUART can be bypassed.
Provision of regulated 5 V, and 3.3 V, DC supplies from the WORKABOUT PRO unregulated
supply voltage VIN:
- 5 V at 100 mA standard.
- 3.3 V at 50 mA standard.
- 5 V at 4 A optional.
•
11.2
Optional loading of extra drivers through the I2C EEPROM.
Schematics
The schematics for the Multi I/O Expansion Module are in
...\Electrical\WORKABOUTPRO\Samples\MultiIOBoard.pdf.
11.3
Connectors
The Multi-I/O Expansion Module has the following connectors:
•
•
•
•
•
•
•
108
100-pin connector to the WORKABOUT PRO main logic board (J1).
Scanner connector to the WORKABOUT PRO main logic board (J2).
Connector for the scanner-port UART (J3).
Connector for the scanner-port USB host (USB host 2) (J4).
Connector for the UART on the 100-pin connector (the FFUART) (J5).
Connector for the USB host on the 100-pin connector (USB host 1) (J6).
Power connector (Ground and +5V) (J7).
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 11: Example: Multi-I/O Expansion Module
Main Logic Board 100-Pin Connector (J1)
Figure 11.2 Connector Locations
J5
J6
J3
J1
J7
J2
Bottom
Top
J4
11.3.1 Main Logic Board 100-Pin Connector (J1)
The full pinout is listed in "Table 7.1 Pinout of the WORKABOUT PRO 100-Pin Connector" on
page 64.
11.3.2 Main Logic Board Scanner Connector (J2)
The full pinout is listed in "Table 8.1 Pinout Of The Scanner Connector" on page 83.
11.3.3 Scanner-Port Serial Connector (J3)
The serial connector (from the UART on the WORKABOUT PRO scanner-port) has the
following pinout:
Table 11.1 Pinout Of Scanner-Port Serial Connector (J3)
Pin
Name
Description
State
Direction Active
During
State
Sleep
1
+3V3_SCANNER Regulated 3.3 V supply from
WORKABOUT PRO
Power
N/A
2
TX_232
Data from WORKABOUT
PRO to scanner device.
At RS-232 levels
Output
B
3
GND
Ground
Power
N/A
4
RX_232
Data from scanner device to
WORKABOUT PRO.
At RS-232 levels
Input
B
6
+5V_SCANNER
Regulated 5 V supply from
WORKABOUT PRO
Power
N/A
Pull-up Or
Pull-down
N/A
N/A
N/A
N/A
None
N/A
N/A
Abbreviations:
N/A= not applicable;
B = both high and low,
L= active low
Psion Teklogix WORKABOUT PRO HDK User Manual
109
Chapter 11: Example: Multi-I/O Expansion Module
USB Host Port 2 Connector (J4)
Table 11.1 Pinout Of Scanner-Port Serial Connector (J3)
Pin
Name
Description
State
Active
Direction State During
Sleep
Pull-up Or
Pull-down
7
CTS
CTS from scanner device to
WORKABOUT PRO.
At RS-232 levels.
Input
L
Pulled
up
100 kΩ
8
RTS
RTS from WORKABOUT
PRO to scanner device.
At RS-232 levels.
Output
L
Low
N/A
Abbreviations:
N/A= not applicable;
B = both high and low,
L= active low
11.3.4 USB Host Port 2 Connector (J4)
The USB Host 2 connector (from the WORKABOUT PRO scanner connector) has the
following pinout:
Table 11.2 Pinout Of USB Host 2 Connector (J4)
Pin
Name
Description
Active State
Direction State During
Sleep
Pull-up Or
Pull-down
1
+3V3_SCANNN
ER
Regulated 3.3 V supply from
WORKABOUT PRO
Power
N/A
N/A
N/A
2
USB_H2_D+
USB host port 2 D+
Bidirectional
B
Pulled
down
15 kΩ
3
GND
Ground
N/A
N/A
N/A
N/A
4
USB_H2_D-
USB host port 2 D-
Bidirectional
B
Pulled
down
15 kΩ
5
+5V
Regulated 5 V supply
Power
N/A
Disabled
N/A
6
+V_IN
Unregulated DC supply from
WORKABOUT PRO
Power
N/A
N/A
N/A
Abbreviations:
N/A= not applicable;
B = both high and low
11.3.5 The FF UART Serial Connector (J5)
The serial connector from the FF UART (on the WORKABOUT PRO 100-pin connector) has the
following pins:
110
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 11: Example: Multi-I/O Expansion Module
The FF UART Serial Connector (J5)
Table 11.3 Pinout Of FF UART Connector (J5)
Pin
Name
Description
Direction
State
Active
During
State
Sleep
Pull-up Or
Pull-down
1
+V_IN
Unregulated DC supply from
WORKABOUT PRO
Power
2
+3V3
Regulated 3.3 V supply from
expansion module.
Power
N/A
N/A
N/A
3
FF_RTS
Ready To Send signal from
WORKABOUT PRO to
scanner device.
Configurable for RS-232 or
TTL levels through SJ12.
Output
L
Low
N/A
4
FF_DTR
Data Terminal Ready signal
from WORKABOUT PRO to
scanner device.
Configurable for RS-232 or
TTL levels through SJ11.
Output
L
Low
N/A
5
GND
Ground
N/A
N/A
N/A
N/A
6
FF_TXD
Data from WORKABOUT
PRO to scanner device.
Configurable for RS-232 or
TTL levels through SJ10.
Output
L
Low
N/.A
7
FF_RI
Ring Indicator signal from
scanner device to WORKABOUT PRO.
Configurable for RS-232 or
TTL levels through SJ17.
Input
L
Pulled
up
100 kΩ
8
FF_DSR
Data Set Ready signal from
scanner device to WORKABOUT PRO.
Configurable for RS-232 or
TTL levels through SJ16
Input
L
Pulled
up
100 kΩ
9
FF_DCD
Data Carrier Detect signal from Input
scanner device to WORKABOUT PRO.
Configurable for RS-232 or
TTL levels through SJ15
L
Pulled
up
100 kΩ
10
FF_CTS
Clear To Send signal from
scanner device to WORKABOUT PRO
Configurable for RS-232 or
TTL levels through SJ14
Input
L
Pulled
up
100 kΩ
Abbreviations:
N/A= not applicable;
L= active low
Psion Teklogix WORKABOUT PRO HDK User Manual
111
Chapter 11: Example: Multi-I/O Expansion Module
The USB Host 1 Connector (J6)
Table 11.3 Pinout Of FF UART Connector (J5)
Pin
Name
Description
Direction
Active State
During
State
Sleep
N/A
11
GND
Ground
N/A
12
FF_RXD
Data from scanner device to
WORKABOUT PRO.
Configurable for RS-232 or
TTL levels through SJ13.
Input
N/A
Pull-up Or
Pull-down
N/A
Abbreviations:
N/A= not applicable;
L= active low
11.3.6 The USB Host 1 Connector (J6)
The serial connector from the FF UART (on the WORKABOUT PRO’s 100-pin connector) has
the following pinout:
Table 11.4 Pinout Of USB Host 1 Connector (J6)
Pin
Name
Description
1
+V_IN
Unregulated DC supply from
WORKABOUT PRO
Power
2
USB_H1_PSW
Power Enable signal from the
WORKABOUT PRO’s USB
hub
Output
3
GND
Ground
4
USB_H1_D-
5
6
Pull-up Or
Pull-down
N/A
Disabled
N/A
N/A
N/A
N/A
N/A
USB host port 1 D-
Bidirectional
B
Pulled
down
15 kΩ
USB_H1_D+
USB host port 1 D+
Bidirectional
B
Pulled
down
15 kΩ
+3.3V
Regulated 3.3 V supply from
expansion module.
Power
N/A
N/A
N/A
Abbreviations:
N/A= not applicable;
B = both high and low
112
Active State
Direction State During
Sleep
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 11: Example: Multi-I/O Expansion Module
The Power Connector (J7)
11.3.7 The Power Connector (J7)
Connector J7 carries power and ground. This connector has the following pinout:
Table 11.5 Pinout Of Power Connector (J7)
Pin
11.4
Name
Description
Direction
State
Active
During
State
Sleep
Pull-up Or
Pull-down
1, 2,
3
GND
Ground
Power
N/A
N/A
N/A
4, 5,
6
VOUT
Output supply voltage. See
Section 11.4.4 and
Section 11.4.3 for
configuration details.
Power
N/A
N/A
N/A
Configuration
The Multi-I/O Expansion Module has a number of jumpers and resistors, (SJ1 through SJ19, plus
R1, R2, R6, and R7), for configuration of its hardware. Several sets of components are optional
depending on how the board is configured:
Figure 11.3 Location Of Configuration Jumpers And Resistors
SJ2
SJ18, SJ19
SJ1
SJ10 - SJ17
SJ4
The jumpers and resistors configure the following options:
•
•
•
•
•
Enable or disable software control of power to the expansion module. (See “Slot Power Control” on page 114.)
Select write control for the EEPROM. (See “EEPROM Write Control” on page 114.)
Configure the output voltage for the high-power option. (See “Voltage Configuration For
Standard-Power Output” on page 115.)
Configure the output voltage for the standard-power option. (See “Voltage Configuration For
Standard-Power Output” on page 115.)
Configure the FORCEON and FORCEOFF/ control signals for the RS-232 converter on the
FFUART port. (See “Control Signals For FFUART Level Converter” on page 117.)
Psion Teklogix WORKABOUT PRO HDK User Manual
113
Chapter 11: Example: Multi-I/O Expansion Module
Slot Power Control
•
Connect the TTL-level signals from the WORKABOUT PRO’s main logic board directly to
the FFUART output connector (J5). (See “TTL Output Option For Scanner Serial Port” on
page 118.)
11.4.1 Slot Power Control
Jumper SJ1 enables or disables control by the WORKABOUT PRO of power to the
expansion module.
SJ1
3
2
1
Jumper Between
State
no jumper
Power not enabled
1 and 2
Power controlled by SLOT_PWR_EN
2 and 3
Power always enabled
11.4.2 EEPROM Write Control
Jumper SJ2 selects write control for the EEPROM.
SJ2
3 2 1
114
Psion Teklogix WORKABOUT PRO HDK User Manual
Notes
Pad 2 is pulled up to +VIN.
Chapter 11: Example: Multi-I/O Expansion Module
Voltage Configuration For Standard-Power Output
Jumper Between
State
Notes
no jumper
The write behaviour depends on the type
of EEPROM installed.
1 and 2
Writing to the EEPROM is disabled
Pad 2 is pulled down to ground.
2 and 3
Writing to the EEPROM is enabled
Pad 2 is pulled up to +3 V.
11.4.3 Voltage Configuration For Standard-Power Output
R1 and R2 set the output voltage for the standard-power supply option of the Expansion Module.
R1
R2
Desired Voltage
R1
R2
3.3V
Open
Jumpered (zero-ohm resistor)
5V
261 kΩ
86.6 kΩ
Configurable voltage
See text
To determine the values of R1 and R2, given the desired output voltage Vout:
1. Select a value for R2. (R2 should be between 50 kΩ and 100 kΩ.)
2. R1 can be found according to the following equation:
Vout
R1 = R2 ⎛⎝ ------------- – 1⎞⎠
1.235
Important: Use these resistors and jumpers ONLY if U4 and its associated components for
the standard-power output are installed. These components are indicated as
“Option Standard Power (SP)” in the schematic on page B-3.
Psion Teklogix WORKABOUT PRO HDK User Manual
115
Chapter 11: Example: Multi-I/O Expansion Module
Voltage Configuration For High-Power Output
11.4.4 Voltage Configuration For High-Power Output
Jumper SJ3, along with R6 and R7, set the output voltage for the Expansion Module high-power
supply option.
3
2
1
SJ3
R6
R7
Desired Voltage
Jumper Between
R6
R7
3.3 V
2 and 3
jumpered (zero-ohm resistor)
open
5V
1 and 2
jumpered (zero-ohm resistor)
open
Configurable voltage
2 and 3
see text
To determine the values of R6 and R7, given the desired output voltage Vout:
1. Select a value for R6. (R6 should be less than 50 kΩ.)
2. R7 can be found according to the following equation:
R7 = R6 ⎛ Vout
------------- – 1⎞
⎝ 1.24
⎠
Important: Use these resistors and jumpers ONLY if U1 and its associated components for
the high-power output are installed. These components are indicated as “Option
High Power (HP)” in the schematic.
116
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 11: Example: Multi-I/O Expansion Module
Control Signals For FFUART Level Converter
11.4.5 Control Signals For FFUART Level Converter
Jumpers SJ18 and SJ19 configure the FORCEON and FORCEOFF/ control signals for the
MAX3243 RS-232 level-converter that handles the signals from the FFUART to J5.
SJ19
3 2 1
SJ18
3 2 1
Jumper Between
SJ18 Signal State
no jumper
FORCEON signal not connected.
1 and 2
FORCEON signal controlled by GPIO43
(pin 74 on the 100-pin connector)
2 and 3
FORCEON signal tied to 3.3 V.
Jumper Between
SJ19 Signal State
no jumper
FORCEOFF/ signal not connected.
1 and 2
FORCEOFF/ signal controlled by GPIO44 (pin 76 on the 100-pin connector).
2 and 3
FORCEOFF/ signal tied to 3.3 V.
Note: Refer to the data sheet for the MAX3243 for the use of these signals.
Psion Teklogix WORKABOUT PRO HDK User Manual
117
Chapter 11: Example: Multi-I/O Expansion Module
TTL Output Option For Scanner Serial Port
11.4.6 TTL Output Option For Scanner Serial Port
Jumpers SJ10 through SJ17 connect the TTL-level serial lines for the scanner serial port from J2
directly to their output connector J5.
SJ12 SJ11 SJ10
SJ17
SJ16
SJ15
SJ14
SJ13
Jumper State
State
No jumper (default)
Signal input on J2 is NOT connected directly to output on J5.
Jumper present
Signal input on J2 is connected directly to output on J5.
The jumpers are assigned to individual signal lines as follows:
Jumper
Number
Signal Line
SJ10
FF_TXD
SJ11
SJ12
FF_DTR
FF_RTS
SJ13
SJ14
SJ15
SJ16
SJ17
FF_RXD FF_CTS FF_DCD FF_DSR FF_RI
Important: U5 (the MAX3243 RS-232 level converter), and its associated components,
MUST NOT be mounted on the board if these jumpers are to be used. These components are indicated as “Option 232” on the schematic.
11.5
Power And Ground
The WORKABOUT PRO provides the following power and ground connections to the Multi-I/O
Expansion Module:
Through the scanner connector (J2):
•
•
118
Ground (pins 1, 2, 11, 12, 15).
+5V_SCANNER (pins 21and 22).
This voltage is +5 V from a DC-DC converter fed by V_IN, the WORKABOUT PRO main
supply. It is switched by the scanner power enable signal.
Psion Teklogix WORKABOUT PRO HDK User Manual
Chapter 11: Example: Multi-I/O Expansion Module
EEPROM Data
•
+3V3_SCANNER (pin 9)
+3.3 V from the WORKABOUT PRO internal DC-to-DC converter.
Through the 100-pin connector (J1):
•
•
Ground (pins 21, 22, 39, 40, 57, 58, 77, 78, 84).
+VIN (pins 1, 2, 3, 4).
This voltage is the WORKABOUT PRO unregulated DC supply.
Ground for both of these connectors is tied together.
These voltages have the following specifications:
Table 11.6 Voltages Supplied To The Multi-I/O Expansion Module
Nominal
Voltage
Supply
Minimum
Voltage
Maximum
Voltage
Continuous Current
+V5_SCANNER
5V
300 mA
+3V3_SCANNER
3.3 V
100 mA
VIN
2V
5V
The voltage VIN is fed by a diode OR of V_BAT (the DC voltage supplied by the WORKABOUT
PRO battery), and DC_IN, the DC power input to the terminal. VIN feeds a DC-to-DC converter;
the output of the converter is switched by the and is known as V+5_BAR.
When the terminal is powered by a DC power supply, VIN will be at 5 V minus a diode drop.
When the terminal is powered by the battery, VIN is at battery voltage, minus a diode drop. (Nominal battery voltage is 3.7 V.) VIN has a minimum of 2 V and a maximum of 5 V.
+5V_SCANNER is maintained by the WORKABOUT PRO DC-to-DC converter at 5 V.
+5V_SCANNER can be switched on and off by software while the WORKABOUT PRO is running, but it is disabled when the WORKABOUT PRO is suspended.
+3V3_SCANNER remains powered when the WORKABOUT PRO is suspended.
11.6
EEPROM Data
The EEPROM in the Multi-I/O Expansion Module must be programmed. See “I2C Device Identification” on page 73 for details.
11.7
Installation
The Multi-I/O Expansion Module fits in the WORKABOUT PRO expansion slot, and fastens to
the metal mounting frame:
The Multi-I/O Expansion Module fastens to the mounting frame with the standard screws
(M2 x 4). When used for development, it is easiest to leave the backplate or endcap off for access
to the connectors on the Multi-I/O Expansion Module. The Multi-I/O Expansion Module needs
only a normal backplate to function, but for exterior cable access, a custom backplate may
be needed.
The scanner cable fits straight between the scanner connector in the WORKABOUT PRO and the
scanner connector on the Multi-I/O Expansion Module. It may need to be folded.
Psion Teklogix WORKABOUT PRO HDK User Manual
119
Chapter 11: Example: Multi-I/O Expansion Module
Installation
Figure 11.4 Arrangement Of Cable Between Main Logic Board And Multi-I/O Expansion Module
120
Psion Teklogix WORKABOUT PRO HDK User Manual
APPENDIX
A
SUPPORT SERVICES / WORLDWIDE OFFICES
Psion Teklogix provides a complete range of product support services to its customers worldwide.
These services include technical support and product repairs.
A.1
Technical Support
For technical support in North America:
Call Toll free:
+1 800 387 8898
Option 3,
or
Direct Dial:
+1 905 813 9900 Ext. 1999
Option 3
For technical support in EMEA (Europe, Middle East and Africa), please contact the local
office listed in the web site below:
http://www.psionteklogix.com/EMEASupport
For technical support in Asia, please contact the local office listed in the web site below:
http://www.psionteklogix.com
Technical Support for Mobile Computing Products is provided via e-mail through the Psion Teklogix customer and partner extranets. To reach the web site, go to www.psionteklogix.com, and
click on the appropriate Teknet link on the home page. Then click on the “Login” button or the
“Register” button, depending on whether you have previously registered for Teknet. Once you
have logged in, search for the “Support Request Form”.
A.2
Product Repairs
For repair service in North America:
Call Toll free:
+1 800 387 8898
Option 2,
or
Direct Dial:
+1 905 813 9900 Ext. 1999
Option 2
For repair service in EMEA (Europe, Middle East and Africa), please contact the local office
listed in the web site below:
http://www.psionteklogix.com/EMEASupport
For repair service in Asia, contact the local office listed in the web site below:
http://www.psionteklogix.com
Psion Teklogix WORKABOUT PRO HDK Developer Guide
A-1
Appendix A: Support Services / Worldwide Offices
Worldwide Offices
A.3
Worldwide Offices
A.3.1
Company Headquarters
Psion Teklogix Inc.
2100 Meadowvale Boulevard
Mississauga
Ontario
Canada L5N 7J9
Tel:
Fax:
E-mail:
A.3.2
+1 905 813 9900
+1 905 812 6300
[email protected]
Canadian Service Centre
Psion Teklogix Inc.
7170 West Credit Ave., Unit #1
Mississauga, Ontario
Canada L5N 7J9
Tel:
A.3.3
+1 800 387 8898
Direct:
Fax:
+ 1 905 813 9900 Ext. 1999
+ 1 905 812 6304
Web:
www.psionteklogix.com
or
Option 2
North American Headquarters And U.S. Service Centre
Psion Teklogix Corp.
1810 Airport Exchange Boulevard
Suite 500
Erlanger, Kentucky
USA 41018
Tel:
Fax:
E-mail:
A-2
Option 2,
+1 859 371 6006
+1 859 371 6422
[email protected]
Psion Teklogix WORKABOUT PRO HDK Developer Guide
Appendix A: Support Services / Worldwide Offices
International Subsidiaries
A.3.4
International Subsidiaries
See also www.psionteklogix.com/Subsidiaries.
Psion Teklogix S.A.
La Duranne
135 Rue Rene Descartes
BP 421000
13591 Aix-En-Provence
Cedex 3; France
Tel:
Fax:
E-mail:
+33 4 42 90 88 09
+33 4 42 90 88 88
[email protected]
Psion Teklogix WORKABOUT PRO HDK Developer Guide
A-3
APPENDIX
B
RESOURCES
B.1
Psion Teklogix WORKABOUT PRO User Manuals
The following user manuals are available at www.PsionTeklogix.com/manuals:
•
•
•
•
•
•
B.2
Psion Teklogix. 2004. WORKABOUT PRO M/C Hand-Held Computer User Manual (Part
number 8000024).
Psion Teklogix. 2005. WORKABOUT PRO Hand-Held Computer With Windows Mobile
2003 SE User Manual (Part number 8100058).
Psion Teklogix. 2006. WORKABOUT PRO Hand-Held Computer With Windows Mobile 5.0
User Manual (Part number 8100107).
Psion Teklogix. 2007. WORKABOUT PRO Hand-Held Computer With Windows Embedded
CE 5.0 User Manual (Part number 8000140).
Psion Teklogix. 2007. WORKABOUT PRO Hand-Held Computer (Model No. 7527) With
Windows Mobile 6 Classic & Professional User Manual (Part number 8000144).
Psion Teklogix. 2005.WA9000, WA9005, WA9006 Scanner Module Installation (Part number
800030).
Other Psion Teklogix Manuals
The following manuals are available at www.PsionTeklogix.com/manuals:
•
•
B.3
Psion Teklogix, 2006, Mobile Devices SDK Developers Guide (Part number 8100016).
Psion Teklogix, 2005, Psion Teklogix WA9000, WA9005, & WA9006 Scanner
Module Installation (Part number 8000030).
Psion Teklogix Downloadable Software
The following software is available at www.PsionTeklogix.com/downloads:
•
•
B.4
Psion Teklogix USB setup utility.
Mobile Devices SDK.
Psion Teklogix Accessory And Parts Information
•
The catalog of accessories and parts for the WORKABOUT PRO is available at
www.PsionTeklogix.com/Accessories.
On the Accessories page:
1. In the Choose a product box select the WORKABOUT PRO variant.
2. In the Choose a category box select the accessory type.
Psion Teklogix WORKABOUT PRO HDK User Manual
B-1
APPENDIX
C
SPECIFICATIONS WORKABOUT PRO M
C.1 Hand-Held Computer Specifications WORKABOUT PRO M . . . . . . . . . . . . . . . . . . . . . 3
C.2 Radio Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
C.4 Battery Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
C.4.1 Standard Battery Pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
C.4.2 High-Capacity Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Psion Teklogix WORKABOUT PRO HDK User Manual
C-1
Appendix C: Specifications WORKABOUT PRO M
Hand-Held Computer Specifications WORKABOUT PRO M
C.1
Hand-Held Computer Specifications WORKABOUT PRO M
Note: Performance specifications are nominal & subject to change without notice.
Note: The WORKABOUT PRO M is no longer available from Psion Teklogix.
Model
•
WORKABOUT PRO M - Model 7225M
Size
•
•
•
•
Length: 8.7" (221mm)
Width: 3" (76mm) at grip area tapering to 3.5" (90mm) at display area.
Depth: 1.2" (31mm) at grip area tapering to 1.7" (44mm) at display area.
Keypad area: 3" (75.5mm) width x 1.4" (36mm) depth
Weight
•
With battery: 454g (16 oz):
- add with scanner expansion module: 75 g (2.6 oz).
- add with 802.11b CF card radio 19 g (0.7 oz).
Display
•
•
•
Monochrome touch screen display.
16 levels of grey.
Backlight: on/off control.
Keyboard
•
•
•
55-key alphanumeric keyboard.
Keyboard backlight.
High durability, hard-topped keys.
Operating System
Microsoft Windows CE .NET Version 4.2
Processor
•
XScale PXA255 @ 400 MHz Processor.
Memory
•
64 MB RAM.
Audio
Indicators
Power Management
•
•
3.8 V Standard Capacity Li-ion rechargeable battery - up to 8 hours of operation.
3.8 V High-Capacity Li-ion rechargeable battery - up to 12 hours of operation.
Psion Teklogix WORKABOUT PRO HDK User Manual
C-3
Appendix C: Specifications WORKABOUT PRO M
Radio Specifications
•
•
•
•
•
Advanced Smart Battery with gas gauge.
Quick swap battery packs.
Built-in fast charger.
Rechargeable, user-replacable internal coin battery.
Also accepts 3 AA alkaline batteries.
Communication
Ports
USB Host port on base for tethered USB devices
(printers, etc.)
Low Insertion Force Docking Station Port with:
- USB Device Port
- USB Host port
- Power in/out
Environmental
Operating Temperature
14°F to 122°F (-10°C to +50°C)
Storage Temperature
-13°F to 140°F (-25°C to +60°C)
Rain And Dust Resistance
IEC 529, classification IP54.
Humidity
5% - 95% RH non-condensing
Shock
Multiple 4 ft. (1.2m) drops to polished concrete.
Approvals
C.2
Safety
UL60950-1, CSA C22.2 No 60950-1
EMC
FCC Part 15 Class B
EN 55022
EN 55024
Laser
IEC 60825-1, Class 2
FDA 21 CFR 1040.10,
1040.11 Class II
In Vehicle Cradle
E Mark
Radio Specifications
802.11b Direct Sequence Spread Spectrum
Transmit Power
100mW max for USA
50mW max for EU countries
Frequency Range
2.400-2.474 for USA, Canada
2.400-2.484GHz for EU
Channels
1 to 11 for USA, Canada
1-13 for EU countries
1-13 or 14 for Japan
Data Rates
C-4
Psion Teklogix WORKABOUT PRO HDK User Manual
1,2,5.5 and 11Mbps
Appendix C: Specifications WORKABOUT PRO M
Scanner Options
C.3
Scanner Options
For details of this scanner see Appendix G: “Specifications Scanners And Imagers”.
•
C.4
SE 1223HP
Battery Specifications
For details of the following batteries see Appendix H: “Specifications WORKABOUT PRO
Batteries”.
•
•
•
C.4.1
Standard Capacity–2000 mAh (Model WA3000-G1)
High-Capacity 3000mAh (Model WA3006)
Maxell ML2032 Rechargeable Coin Battery
Standard Battery Pack
Lithium Ion Polymer Battery (Li-Polymer)
Chemistry Capacity
1750 mAh nominal at 350mA discharge 20 °C (68° F) to
2.8V(minimum)
Voltage
3.7V nominal (2.8V min. to 4.2V max.)
Cell Configuration
1S2P (2 parallel connected cells)
Cell Type
Lithium-ion Polymer Battery
Max. Discharge
Current
1A (-10° C to 60° C) -- (14° F to 140° F)
Charge Algorithm
CC to CV
Max. Charge Voltage
4.2V +/- 0.05V
Max. Charge Current
800 mA
Discharge Cut-off
2.6V min – DS2761 protection circuit initiates
Recommended
Fast Charge
1550 mA for 2.5hrs
Max. Fast Charge Time 3.0 hrs.
Recommended Termination Taper Current
50 - 100 mA
Recommended Charge
Termination Timeout
30 min.
Charge Temperature
0° C to 45 °C (32° F to 113° F)
Discharge Temperature
-20° C to 60° C (-4° F to 140° F)
Recommended Termination Taper Current
50 - 100 mA
Recommended Charge
Termination Timeout
30 min.
Charge Temperature
0° C to 45 °C (32° F to 113° F)
Discharge Temperature
-20° C to 60° C (-4° F to 140° F)
Storage Temperature
-20° C to 60° C (-4° F to 140° F) Storing battery at elevated
temperatures is not recommended.
Psion Teklogix WORKABOUT PRO HDK User Manual
C-5
Appendix C: Specifications WORKABOUT PRO M
High-Capacity Battery Pack
C.4.2
Cycle Life
300 cycles minimum with no degradation below 80% of
nominal capacity based on standard charge / standard discharge rates (to 2.8V) @ 25ºC
Impedance
45 mΩ max. @ 1kHz AC only the battery cell
Total Internal Resistance
200 mΩ max., fully charged new pack (including cell resistance and protection circuit resistance) @ 1kHz AC
High Temperature
Recovery
>60% nominal capacity after 20 days @ 60° C (full charge) -(140° F)
Low Temperature
Recovery
>80% nominal capacity after 72 hours @ -20° C (full charge)
-- (-4° F)
Capacity recovery
-20° C to 60° C (-4° F to 140° F) >80% capacity recovery
within 1 month
-20° C to 45° C (-4° F to 113° F) >75% capacity recovery
within 3 month
-20° C to 20° C (-4° F to 68° F) >70% capacity recovery
within 1 year
High-Capacity Battery Pack
Lithium Ion Polymer Battery (Li-Polymer)
Chemistry Capacity
2625 mAh nominal at 350mA discharge 20 °C (68° F) to
2.8V(minimum)
1800 mAh nominal at 300mA discharge at –20 °C to
2.8V (minimum)
C-6
Voltage
3.7V nominal (2.8V min. to 4.2V max.)
Cell Configuration
1S3P (3 parallel connected cells)
Cell Type
Lithium-ion Polymer Battery
Max. Discharge Current
1.7A (-10° C to 60° C) -- (14° F to 140° F)
0.5C (-20° C to 60° C) -- (-4° F to 140° F)
Charge Algorithm
CC to CV
Max. Charge Voltage
4.2V +/- 0.05V
Max. Charge Current
900 mA
Discharge Cut-off
2.6V min – DS2761 protection circuit initiates
Recommended
Fast Charge
2325 mA for 4.0 hrs
Max. Fast Charge Time
5.0 hrs
Recommended Termination Taper Current
50 - 100 mA
Recommended Charge
Termination Timeout
30 min.
Charge Temperature
0° C to 45 °C (32° F to 113° F)
Discharge Temperature
-20° C to 60° C (-4° F to 140° F)
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix C: Specifications WORKABOUT PRO M
High-Capacity Battery Pack
Recommended Termination Taper Current
50 - 100 mA
Recommended Charge
Termination Timeout
30 min.
Charge Temperature
0° C to 45 °C (32° F to 113° F)
Discharge Temperature
-20° C to 60° C (-4° F to 140° F)
Storage Temperature
-20° C to 60° C (-4° F to 140° F) Storing battery at elevated
temperatures is not recommended.
Cycle Life
300 cycles minimum with no degradation below 80% of
nominal capacity based on standard charge / standard discharge rates (to 2.8V) @ 25ºC
Impedance
35 mΩ max. @ 1kHz AC only the battery cell
Total Internal Resistance
210 mΩ max., fully charged new pack (including cell resistance and protection circuit resistance) @ 1kHz AC
High Temperature
Recovery
>60% nominal capacity after 20 days @ 60° C (full charge) -(140° F)
Low Temperature Recov- >80% nominal capacity after 72 hours @ -20° C (full charge)
ery
-- (-4° F)
Capacity recovery
-20° C to 60° C (-4° F to 140° F) >80% capacity recovery
within 1 month
-20° C to 45° C (-4° F to 113° F) >75% capacity recovery
within 3 month
-20° C to 20° C (-4° F to 68° F) >70% capacity recovery
within 1 year
Psion Teklogix WORKABOUT PRO HDK User Manual
C-7
APPENDIX
D
SPECIFICATIONS WORKABOUT PRO C, S & ME
D.1 Hand-Held Computer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
D.1.1 Model Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
D.2 WORKABOUT PRO C Variant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
D.3 WORKABOUT PRO S Variant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
D.4 WORKABOUT PRO ME Variant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
D.5 WORKABOUT PRO C, S, and ME Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
D.6 Radio Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
D.7 Scanner Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
D.8 Battery Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Psion Teklogix WORKABOUT PRO HDK User Manual
D-1
Appendix D: Specifications WORKABOUT PRO C, S & ME
Hand-Held Computer Specifications
D.1
Hand-Held Computer Specifications
Note: Performance specifications are nominal & subject to change without notice.
D.1.1
Model Variants
•
•
•
D.2
WORKABOUT PRO C - Model 7525C
WORKABOUT PRO S - Model 7525S
WORKABOUT PRO ME (monochrome enhanced) - Model 7525ME
WORKABOUT PRO C Variant
Size
•
•
•
Length: 221 mm (8.7").
Width: 76 mm (3") at grip area, tapering to 92 mm (3.6") at display area.
Depth: 31 mm (1.2") at grip area, tapering to 42 mm (1.7") at display area.
Weight
•
With battery: 454 g (16 oz);
- with SE 1223HP scanner expansion module: add 75 g (2.6 oz).
- with 802.11g CF card radio: add 19g (0.7 oz).
Display
•
•
•
•
•
•
Colour touch screen display
Diagonal measurement: 8.9 cm (3.5 in).
¼ VGA: 240 pixels by 320 pixels.
16-bit colour.
Transflective, portrait mode TFT.
High reliability LCD backlight:
- On/off control.
- Contrast control.
•
•
•
Sunlight readable.
Passive stylus or finger operation.
Signature capture capability.
Keyboard
•
•
•
55-key alphanumeric keyboard.
Keyboard backlight.
High durability, hard-topped keys.
Memory
•
•
64 MB Flash.
128 MB RAM.
Psion Teklogix WORKABOUT PRO HDK User Manual
D-3
Appendix D: Specifications WORKABOUT PRO C, S & ME
WORKABOUT PRO S Variant
D.3
WORKABOUT PRO S Variant
Size
•
•
•
Length: 190 mm (7.5”).
Width: 75 mm (2.9”) grip area tapering to 98 mm (3.8") at display area (including side
scan buttons).
Depth: 31 mm (1.2") at grip area tapering to 44 mm (1.7") at display area.
Weight
•
With battery: 421 g (13.5 oz);
- with SE 1223HP scanner expansion module: add 75 g (2.6 oz).
- with 802.11g CF card radio: add 19 g (0.7 oz)
Display
•
•
•
•
•
•
Colour touch screen display
Diagonal measurement: 8.9 cm (3.5 in).
¼ VGA: 240 pixels by 320 pixels.
16-bit colour.
Transflective, portrait mode TFT.
High reliability LCD backlight:
- On/off control.
- Contrast control.
•
•
•
Sunlight readable.
Passive stylus or finger operation.
Signature capture capability.
Keyboard
•
•
•
29-key numeric keyboard.
Keyboard backlight.
High durability, hard-topped keys.
Memory
•
•
D.4
64 MB Flash.
128 MB RAM.
WORKABOUT PRO ME Variant
Size
•
•
•
Length: 221 mm (8.7").
Width: 76 mm (3") at grip area, tapering to 92 mm (3.6") at display area.
Depth: 31 mm (1.2") at grip area, tapering to 42 mm (1.7") at display area.
Weight
•
With battery: 454 g (16 oz);
- with SE 1223HP scanner expansion module: add 75 g (2.6 oz).
- with 802.11g CF card radio: add 19g (0.7 oz).
D-4
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix D: Specifications WORKABOUT PRO C, S & ME
WORKABOUT PRO C, S, and ME Variants
Display
•
•
•
•
•
Monochrome touch screen display.
Diagonal measurement: 8.9 cm (3.5 in).
¼ VGA: 240 pixels by 320 pixels.
Transflective, portrait mode TFT.
High reliability LCD backlight:
- On/off control.
- Contrast control.
•
•
•
Sunlight readable.
Passive stylus or finger operation.
Signature capture capability.
Keyboard
•
•
•
55-key alphanumeric keyboard.
Keyboard backlight.
High durability, hard-topped keys.
Memory
•
•
D.5
64 MB Flash.
64 MB RAM.
WORKABOUT PRO C, S, and ME Variants
Processor
•
PXA255, 400 MHz processor.
Operating System
•
•
•
Microsoft Windows CE .NET 4.2
Microsoft Windows Mobile 5.0
Microsoft Windows Mobile 2003 SE
Audio
•
Internal speaker with volume control.
Indicators
•
LED indicating battery charge status (programmable).
Power Management
•
•
•
•
•
•
•
3.7 V Standard Capacity Li-ion rechargeable battery - up to 8 hours of operation.
3.7 V High-Capacity Li-ion rechargeable battery - up to 12 hours of operation.
Advanced Smart Battery w/ gas gauge.
Quick swap battery packs.
Built-in fast charger.
Rechargeable, user-replacable internal coin battery.
Also accepts 3 AA alkaline batteries.
Psion Teklogix WORKABOUT PRO HDK User Manual
D-5
Appendix D: Specifications WORKABOUT PRO C, S & ME
WORKABOUT PRO C, S, and ME Variants
Expansion Slots
•
•
•
One SD/MMD memory card slot (user accessible).
endcap USB interface supports GPS interface.
100-pin expansion interface supports:
- PCMCIA (type II).
- GSM/GPRS EDGE.
- Customized expansion modules developed using the WORKABOUT PRO HDK.
•
Flex cable interface with robust connector supports
- Scanner (serial) modules.
- Imager (USB) modules.
•
One CF card slot (type II).
Communication
Ports
USB Host port on base for tethered USB devices
(printers, etc.)
Low Insertion Force Docking Station Port with:
- USB Device Port
- USB Host port
- Power in/out
Environmental
Operating Temperature
14°F to 122°F (-10°C to +50°C)
Storage Temperature
-13°F to 140°F (-25°C to +60°C)
Rain And Dust Resistance
IEC 529, classification IP54.
Humidity
5% - 95% RH non-condensing
Shock
Multiple 4 ft. (1.2m) drops to polished concrete.
Approvals
D-6
Safety
UL60950-1, CSA C22.2 No 60950-1
EMC
FCC Part 15 Class B
EN 55022
EN 55024
Laser
IEC 60825-1, Class 2
FDA 21 CFR 1040.10,
1040.11 Class II
Bluetooth:
1.1 on C & S models
In-Vehicle Cradle
E Mark
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix D: Specifications WORKABOUT PRO C, S & ME
Radio Options
D.6
Radio Options
For details of these radios see Appendix F: “Specifications WORKABOUT PRO Radios”.
•
•
•
D.7
802.11g Direct Sequence Spread Spectrum (Model Number RA2040)
802.11g Direct Sequence Spread Spectrum (Model Number RA2041)
Variants C and S only: Integrated Bluetooth class II, version 1.2.
Scanner Options
For details of these scanners and imagers see Appendix G: “Specifications Scanners And
Imagers”.
•
•
•
•
•
D.8
SE 1223HP, LR, ALR
SE955HP
EV15 Imager
HHP5180 Imager
SX5393 Imager
Battery Options
For details of these batteries see Appendix H: “Specifications WORKABOUT PRO Batteries”.
•
•
•
Standard Capacity–2000 mAh (Model WA3000-G1.)
High Capacity–3000 mAh (Model WA3006).
Maxell ML2032 Rechargeable Coin Battery.
Psion Teklogix WORKABOUT PRO HDK User Manual
D-7
E
APPENDIX
WORKABOUT PRO 2ND. GENERATION
E.1 WORKABOUT PRO Specifications . . . .
E.1.1 WORKABOUT PRO C Variant .
E.1.2 WORKABOUT PRO S Variant. .
E.1.3 WORKABOUT PRO All Variants
E.2 Radio Options . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3
3
3
3
8
E.3 Battery Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
E.4 Scanner Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
E.4.1 Scanner/Imager Model Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Psion Teklogix WORKABOUT PRO HDK User Manual
E-1
Appendix E: WORKABOUT PRO 2nd. Generation
WORKABOUT PRO Specifications
E.1
WORKABOUT PRO Specifications
Note: Performance specifications are nominal & subject to change without notice.
Model Variants
•
•
E.1.1
WORKABOUT PRO C – Model 7527C-G2
WORKABOUT PRO S – Model 7527S-G2
WORKABOUT PRO C Variant
Size
•
•
•
Length: 223 mm (8.775").
Height: 75 mm (2.95") grip area tapering to 100 mm (3.94") at display area (including side
scan buttons).
Depth: 31 mm (1.22") at grip area tapering to 42 mm (1.65") at display area.
Weight Without Battery Pack
•
455 g (1.0 lb).
Keyboard
•
•
•
E.1.2
55-key alphanumeric keyboard.
Keyboard backlight.
High durability, hard-topped keys.
WORKABOUT PRO S Variant
Size
•
•
•
Length: 200 mm (7.87").
Height: 75 mm (2.95") grip area tapering to 100 mm (3.94") at display area (including side
scan buttons).
Depth: 31 mm (1.22") at grip area tapering to 42 mm (1.65") at display area.
Weight Without Battery Pack
•
390 g (0.859 lb).
Keyboard
•
•
•
E.1.3
29-key numeric keyboard.
Keyboard backlight.
High durability, hard-topped keys.
WORKABOUT PRO All Variants
Display
•
•
•
•
Colour touch screen display
Diagonal measurement: 9.144 cm (3.6 in).
Full VGA: 480 pixels by 640 pixels.
Transflective, portrait mode TFT.
Psion Teklogix WORKABOUT PRO HDK User Manual
E-3
Appendix E: WORKABOUT PRO 2nd. Generation
WORKABOUT PRO All Variants
•
•
•
•
•
•
Adjustable backlight.
Sunlight readable.
High reliability LCD backlight.
Passive stylus or finger operation.
Signature capture capability.
Bezel: replaceable and customizable.
Processor
•
•
PXA270 @ 520 MHz, 32 bit RISC CPU
128 MB flash, 128 MB RAM
Operating System
•
•
•
Microsoft® Windows® CE 5.0
Microsoft® Windows® Mobile® 6 Classic
Microsoft® Windows® Mobile® 6 Professional
Audio
•
•
•
Mono speaker.
Mono microphone.
High volume 92 db beeper.
Indicators
•
LED indicating battery charge status (programmable).
Wireless Communication
Optional expansion modules for:
•
•
•
•
•
•
•
•
•
•
802.11b/g (via Compact Flash) operating in the 2.4GHz band.
Supports IEEE 802.11b data rates of 1,2,5.5 and 11Mbps using Direct Sequence Spread
Spectrum (DSSS).
Supports IEEE 802.11g data rates of 6,9,12,24,36,48 and 54Mbps, using Orthogonal
Frequency Division Multiplexing (OFDM) base band modulation.
GSM/GPRS EDGE (via expansion interface).
Quad-Band – 850/900/1800/1900
Voice and Data.
GPRS Class B, Multi-Slot Class 12
EGPRS Class B, Multi-Slot Class 12
Integrated Bluetooth class II, ver 1.2
Working Range:16.4 ft.to 32.81 ft. (5 m to 10 m).
Note: 802.11b/g, GSM, and Bluetooth are available simultaneously.
E-4
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix E: WORKABOUT PRO 2nd. Generation
WORKABOUT PRO All Variants
Bar Code Applications
•
•
•
•
•
Optional 1D imager expansion module
Optional 2D imager expansion module
Optional 1D SE955 laser scanner expansion module
Optional 1D SE1223 High Performance laser scanner expansion module
Optional bolt-on pistol grip
Note: All are user upgradeable
RFID Modules
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
HF Module
Frequency: 13.56 MHz
Tags supported: ISO 15693, Philips ICode™; TI TagiIt™; Tagsys (C210,C220,C240,C270)
Read/write range up to: 3.15 in.(80 mm)
MIFARE module
Frequency: 13.56 MHz
Tags supported: ISO 14443 A&B, Mifare
Read/write range up to: 1.97 in.(50 mm)
LF module
Frequency: 125 KHz, 134.2 KHz
Tags supported: EM 4x0x, EM 4x50; Hitag 1 & 2; ISO HDXA & FDXB
Read/write range up to: 2.756 in.(70 mm)
UHF module
Frequency: 868 MHz or 915 MHz
Read range: up to 4.92 ft.(150 cm) [915MHz] and up to 2.62 ft.(80 cm) [868 MHz]
Tag supported: EPC Class 1 Gen 2, other protocols depending on regions
User Interface
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Colour Touch Screen Display 3.6 in.(9.144 cm) diagonal
Full VGA 480x640 resolution
Transflective, portrait mode TFT
Adjustable Backlight
Sunlight readable (for outdoor use)
High reliability LED backlight
Easily replaceable and customizable bezel
Touchscreen
Passive stylus or finger operation
Signature capture
Keyboards
Full Alpha-Numeric (C model)
Numeric (S model)
Ergonomically enhanced for ambidextrous, one-hand operation
Backlit, high durability hard-capped keys
Psion Teklogix WORKABOUT PRO HDK User Manual
E-5
Appendix E: WORKABOUT PRO 2nd. Generation
WORKABOUT PRO All Variants
•
•
Indicators And Controls
LED indicates battery charge status
Programming Environment
•
•
•
•
•
•
Psion Teklogix Mobile Devices SDK
Hardware Development Kit (HDK)
.NET and C++ programming using Microsoft® Visual Studio® 2005
Java programming supporting JDK 1.2.2 or higher
Standard Protocol APIs
Windows sockets (CE .NET)
Application Software
•
•
•
•
•
Internet Explorer 6.0 incl.with Windows CE 5.0
Unique Psion Teklogix Voice Dialer and Contacts Manager incl.Windows CE 5.0
PTX Connect VoIP
Optional Open TekTerm terminal emulation software, supports IBM 5250,IBM 3270,
HP2392, ANSI and TESS
Mobile Control Center (MCC) device management
Expansion Slots
•
•
•
One SD/MMC memory card slot (user accessible).
Endcap USB Interface supports GPS expansion module.
100-PIN expansion interface supports:
- PCMCIA (type II).
- GSM/GPRS EDGE modules.
- Customized expansion modules developed using Psion Teklogix WORKABOUT
PRO HDK.
•
Flex cable interface with robust connector, supports:
- Scanner (serial) modules.
- Imager (USB) modules.
•
One Type II CF Card Slot.
External Connectors
•
•
•
One Tether connection with full RS-232 and USB 1.1 functionality
One Low-Insertion Force (LIF) docking connector
DC Power Jack
Power Management
•
•
•
•
•
•
E-6
Optional 3.7V, 3000 mAh High Capacity Battery Pack
Optional 3.7V, 4000 mAh Super High Capacity Battery Pack
Advanced Smart Battery with gas gauge
3 power source options: Runs off battery, AC power, or automotive power supplies
Built-in charger
Rechargeable, user replaceable backup battery pack
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix E: WORKABOUT PRO 2nd. Generation
WORKABOUT PRO All Variants
Environmental
•
•
•
•
•
Withstands 26 drops (on 12 edges,8 corners, 6 faces) at 5 ft.(1.5 meters) to polished concrete
while powered on and configured with accessories such as CF radio, scanner/imager, and
pistol grip
Rain/Dust: IP65,IEC 60529
Operating Temperature: 14°F to 122°F (-10°C to +50°C)
5%-95% RH non-condensing
Storage Temperature: -40°F to 140°F (-40°C to +60°C)
Physical Dimensions And Weight
•
•
•
•
•
•
•
WORKABOUT PRO C:
8.775 in. x 2.95/3.94 in. x 1.22/1.65 in. (223 mm x 75/100 mm x 31/42 mm)
WORKABOUT PRO S:
7.87 in. x 2.95/3.94 in. x 1.22/1.65 in. (200 mm x 75/100 mm x 31/42 mm)
Weight (w/o battery pack):
WORKABOUT PRO C:1 lbs (455 g)
WORKABOUT PRO S:.859 lbs (390 g)
Power Accessories
•
•
•
•
AC power supply (charge & operate hand-held)
Automotive power supply (charge & operate hand-held)
Single and Quad slot battery pack chargers
Powered cradle for vehicle mount applications
Communication Accessories
•
•
•
•
Quad Dock (4-site) with 10/100 BaseT Ethernet and charge functions
Desktop Docking Station (charges hand-held & spare battery) provides USB1.1 host and
device ports and supports optional plug-on expansion modules supporting 10/100 BaseT Ethernet or RS-232 connections
USB cable supports Active Sync without requiring a docking station
Optional endcaps supporting RS-232, TTL, and IrDA
Carrying Accessories
•
Hand-strap, pistol grip with trigger, holster and various protective carrying cases and pouches.
Approvals
Safety:
CSA/UL60950-1, IEC 60950-1, EN60950-1
EMC:
FCC Part 15 Class B
EN 55022
EN 55024
EN 301 489
Laser:
IEC 60825-1, Class 2
FDA 21 CFR 1040.10.
1040.11 Class II
Psion Teklogix WORKABOUT PRO HDK User Manual
E-7
Appendix E: WORKABOUT PRO 2nd. Generation
Radio Options
E.2
Bluetooth:
1.2
RF:
Bluetooth and 802.11b/g: EN300 328, Part 15.247
GSM/GPRS:
EN301 511; EN50360/361, NAPRD03; 3GPP51.010;
FCC Parts 22 & 24; Industry Canada; RSS-132 & 133
In-Vehicle Cradle:
e Mark
Radio Options
For details of these radios see Appendix F: “Specifications WORKABOUT PRO Radios”.
•
•
Integrated Bluetooth class II, version 1.2.
Optional expansion models:
- 802.11b/g DSSS radio- Model RA2041.
- GSM/GPRS/EDGE radio - Model RA3030-G2.
E.3
Battery Options
For details of these batteries see Appendix H: “Specifications WORKABOUT PRO Batteries”.
•
•
E.4
High-Capacity (Model WA3006)
Super High-Capacity (Model WA3010)
Scanner Options
For details of these scanners and imagers see Appendix G: “Specifications Scanners And
Imagers”.
•
•
•
•
E.4.1
E-8
SE 1223HP, LR, ALR
SE955HP
EV15 Imager
HHP5180 Imager
Scanner/Imager Model Numbers
Scanner/Imager
Engine
Kit Model Number
Form Factor
1D Laser SE955
WA9102-G1
Endcap without GSM
WA9112-G1
Endcap with GSM
WA9002-G1
Pod
1D Laser
SE1223HP
WA9000-G1
Pod
1D Laser
SE1223LR
WA9005-G1
Pod
1D Laser
SE1223ALR
WA9006
Pod (non-RoHS)
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix E: WORKABOUT PRO 2nd. Generation
Scanner/Imager Model Numbers
Scanner/Imager
Engine
Kit Model Number
Form Factor
1D Imager EV15
WA9103-G1
Endcap without GSM
WA9113-G1
Endcap with GSM
WA9003-G1
Pod
2D Imager
SX5393
WA9010
Pod (non-RoHS)
WA9007-G1
Slim Pod
2D Imager HHP
5180
WA8010-G1
Endcap without GSM
WA8110-G1
Endcap with GSM
WA9012-G1
Slim Pod
Psion Teklogix WORKABOUT PRO HDK User Manual
E-9
APPENDIX
F
SPECIFICATIONS WORKABOUT PRO RADIOS
F.1 Radio Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
F.2 802.11g Direct Sequence Spread Spectrum (Model RA2040) . . . . . . . . . . . . . . . . . . . . . . 3
F.3 802.11b/g Direct Sequence Spread Spectrum (DSSS) (Model RA2041) . . . . . . . . . . . . . . . . . 3
F.4 GSM/GPRS/EDGE Radio (Model RA3030-G2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
F.5 Bluetooth Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Psion Teklogix WORKABOUT PRO HDK User Manual
F-1
Appendix F: Specifications WORKABOUT PRO Radios
Radio Specifications
F.1
Radio Specifications
Note: Performance specifications are nominal & subject to change without notice.
Consult the Accessories Catalog at www.PsionTeklogix.com/Accessories to ensure that a
specific device is still available.
This appendix describes all the radios that are available in the following WORKABOUT PRO
variants:
• WORKABOUT PRO C
• WORKABOUT PRO S
• WORKABOUT PRO ME
• WORKABOUT PRO 2nd. Generation C
• WORKABOUT PRO 2nd. Generation S
Consult the specifications for your WORKABOUT PRO to find out which radios are compatible
with it.
F.2
F.3
802.11g Direct Sequence Spread Spectrum (Model RA2040)
Form Factor
Compact Flash
Antenna Port
Single U.FL jack, no diversity
Transmit Power
20 mW
Frequency Range
2.400 - 2.4835 GHz, all versions
Channels
1 - 11 for USA, Canada
1- 13 for EU countries
RX Sensitivity
(8% BER, 1024 bytes packet) =
-89dBm @ 1Mbps, -87dBm @ 11Mbps,
-83dBm @ 6Mbps, -72dBm @ 54Mbps
Data Rates
6, 9, 12, 18, 24, 36, 48 & 54Mbps
802.11b/g Direct Sequence Spread Spectrum (DSSS) (Model RA2041)
Form factor
Compact Flash Type I extended
Antenna port
Two Hirose U.FL connectors for antenna diversity
Transmit Power
802.11g: 32mW maximum (+15 dBm)
802.11b: 80mW maximum (+19 dBm)
Frequency Range
2.400 - 2.4897 GHz
Channels
FCC:
11
ETSI:
13
TELEC:
13
RX Sensitivity
-96dBm @ 1Mbps, -90dBm @ 11Mbps,
-94dBm @ 6Mbps, -75dBm @ 54Mbps
Data Rates
802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps
802.11b: 1, 2, 5.5, 11 Mbps
Psion Teklogix WORKABOUT PRO HDK User Manual
F-3
Appendix F: Specifications WORKABOUT PRO Radios
GSM/GPRS/EDGE Radio (Model RA3030-G2)
F.4
GSM/GPRS/EDGE Radio (Model RA3030-G2)
Quad-Band GSM 850/900/1800/1900 MHz
EDGE (E-GPRS) multi-slot class 10
GPRS multi-slot class 12
GSM release 99
Output power:
- Class 4 (2 W) for EGSM850
- Class 4 (2 W) for EGSM900
- Class 1 (1 W) for GSM1800
- Class 1 (1 W) for GSM1900
Control via AT commands (Hayes 3GPP TS 27.007 and 27.005)
SIM Application Toolkit (release 99)
TCP/IP stack access via AT commands
Internet Services:
TCP, UDP, HTTP, FTP, SMTP, POP3
Supply voltage range:
3.2 to 4.3 V
Specifications for:
EDGE data transmission:
EDGE class 10: max 236.8 kbps (downlink)
Mobile station class B
Modulation and coding scheme MCS 1-9
GPRS data transmission:
GPRS class 12
Mobile station class B
PBCCH support
Coding schemes CS 1-4
CSD data transmission:
Up to 14.4 kbps
V.110
Non-transparent mode
USSD support
SMS:
Point-to-point MO and MT
SMS cell broadcast
Text and PDU mode
Fax:
Group 3, class 1
Voice:
Triple-rate codec for HR, FR, and EFR
Adaptive multi-rate AMR
Basic hands-free operation
Echo cancellation
Noise reduction
F-4
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix F: Specifications WORKABOUT PRO Radios
Bluetooth Radio
Interfaces:
Hirose U.FL-R-SMT 50 ohm antenna connector
Antenna solder pad
Molex 80-pin board-to-board connector
- Power supply
- Audio: 2x analog, 1x digital
- 2 x serial interface (ITU-T V.24 protocol)
- USB 2.0 full speed
- SIM card interface 3 V, 1.8 V
- I2C bus
F.5
Bluetooth Radio
Embedded (920 kbps serial interface)
Bluetooth Version
1.2 compliant (features Adaptive Frequency Hopping for
better co-existence with 802.11 radio)
Chip Antenna
2dBi peak
Transmit Power
-3dBm (0.5mW) minimum, +4dBm (2.5mW) max
Frequency Range
2.400 - 2.4835 GHz
RX Sensitivity
-80dBm max
(BER<=0.1%)
Data Rate
732.2 kbps and 57.6 kbps asymmetric,
433.9 kbps symmetric
Psion Teklogix WORKABOUT PRO HDK User Manual
F-5
G
APPENDIX
SPECIFICATIONS SCANNERS AND IMAGERS
G.1 Scanner and Imager Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
G.2 Scanner Specifications . . . . . . . . . . . . . . . . . . . . .
G.2.1 SE 1223HP, LR, ALR And SE 955HP Specifications
G.2.1.1 SE 1223HP Decode Zone . . . . . . . . . .
G.2.1.2 SE 1223LR Decode Zone . . . . . . . . . .
G.2.1.3 SE 1223ALR Decode Zone . . . . . . . . .
G.2.1.4 SE 955HP Decode Zone . . . . . . . . . . .
G.3.1 EV15 Imager Specifications . . . . . . . . . . . . .
G.3.1.1 EV15 Imager Decode Zone . . . . . . . . .
G.3.2 HHP5180 Imager Specifications . . . . . . . . . . .
G.3.2.1 HHP5180 Imager Decode Zone . . . . . . .
G.3 Imager Specifications . . . . . . . . . . . . . . . . . . . . . .
G.3.1 EV15 Imager Specifications . . . . . . . . . . . . .
G.3.1.1 EV15 Imager Decode Zone . . . . . . . . .
G.3.2 HHP5180 Imager Specifications . . . . . . . . . . .
G.3.2.1 HHP5180 Imager Decode Zone . . . . . . .
G.3.3 SX5393 Imager Specifications . . . . . . . . . . . .
G.3.3.1 SX5393 Imager Decode Zone . . . . . . . .
G.3.4 SX5400 Imager Specifications . . . . . . . . . . . .
G.3.4.1 SX5400 Imager Decode Zone . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Psion Teklogix WORKABOUT PRO HDK User Manual
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
G-1
. 3
. 3
. 4
. 4
. 5
. 5
. 6
. 6
. 7
. 7
. 6
. 6
. 6
. 7
. 7
. 8
. 9
10
11
Appendix G: Specifications Scanners And Imagers
Scanner and Imager Specifications
G.1
Scanner and Imager Specifications
Note: Performance specifications are nominal & subject to change without notice.
Consult the Accessories Catalog at www.PsionTeklogix.com/Accessories to ensure that a
specific device is still available.
This appendix describes all the scanners and imagers that are available in the following WORKABOUT PRO variants:
• WORKABOUT PRO C
• WORKABOUT PRO S
• WORKABOUT PRO ME
• WORKABOUT PRO 2nd. Generation C
• WORKABOUT PRO 2nd. Generation S
Consult the specifications for your WORKABOUT PRO to find out which radios are compatible
with it.
G.2
Scanner Specifications
G.2.1
SE 1223HP, LR, ALR And SE 955HP Specifications
Scan Engine
SE 1223HP
SE 1223LR
SE 1223ALR
SE 955HP
Scan Angle
42º ± 2º
23º ± 2º
13º ± 2º
47° ± 3°
default / 35° ±
3° reduced
Scan Rate
35 (± 5)
scans/sec (bidirectional)
35 (± 5)
scans/sec (bidirectional)
35 (± 5)
scans/sec (bidirectional)
104 (± 12)
scans/sec
(bi-directional)
Scan Pattern
Linear
Linear
Linear
Linear
Wavelength
650nm
650nm
650nm
650nm
Input Voltage
5.0 VDC ±
10%
5.0 VDC ±
10%
5.0 VDC ±
10%
3.0-5.5 VDC ±
10%
Input Current
110 mA typical
115 mA typical
115 mA
typical
65 mA typical
Standby
Current
130 µA typical
70 µA max.
70 µA typical
8 µA max
Operating
Temperature
-40ºC to 60ºC
-40ºF to 140ºF
-30º to 55ºC
-22ºF to 131ºF
-30°C to 55°C
-22ºF to 131ºF
-20° to 60° C
-4° to 140° F
Print Contrast
Minimum 20%
absolute
dark/light
reflectance
measured at
650 nm
Minimum 40%
absolute
dark/light
reflectance
measured at
650 nm
Minimum
40% absolute
dark/light
reflectance
measured at
650 nm
Minimum
25% absolute
dark/light
reflectance
measured at
650 nm
Psion Teklogix WORKABOUT PRO HDK User Manual
G-3
Appendix G: Specifications Scanners And Imagers
SE 1223HP, LR, ALR And SE 955HP Specifications
Scan Engine
SE 1223HP
SE 1223LR
SE 1223ALR
SE 955HP
Dimensions
1.93 cm max.
H x 3.84 cm
max. W x 3.51
cm max. D
1.93 cm max. H
x 3.84 cm max.
W x 3.51 cm
max. D
1.93 cm max.
H x 3.84 cm
max. W x 3.51
cm max. D
1.21 cm H x
2.16 cm W x
1.55 cm (max)
0.76 in. max. H
x 1.51 in. max.
W x 1.38 in.
max. D
0.76 in. max. H
x 1.51 in. max.
W x 1.38 in.
max. D
0.76 in. max.
H x 1.51 in.
max. W x 1.38
in. max. D
UPC/EAN,
Code 128,
Code 39, Code
93, I 2 of 5,
Discrete 2 of 5,
Codabar, MSI
UCC/EAN
128, TriOptic
Code 39
UPC/EAN,
Code 128,
Code 39, Code
93, I 2 of 5,
Discrete 2 of 5,
Codabar, MSI
UCC/EAN
128, TriOptic
Code 39
UPC/EAN,
Code 128,
Code 39, Code
93, I 2 of 5,
Discrete 2 of
5,
Codabar, MSI
UCC/EAN
128, TriOptic
Code 39
Symbologies
0.47 in. H x
0.85 in. W x
0.61 in. D
(max)
UPC/EAN,
Code 128,
Code 39, Code
93, I 2 of 5,
Discrete 2 of
5, Codabar,
MSI Plessey
G.2.1.1 SE 1223HP Decode Zone
4,844 Lux to 86,112 Lux
Minimum
range
Width of field
Maximum
range
Width of field
Inches
Inches
Inches
Inches
Mil Size
5
2.75
1.25
7
3
7.5
2.25
1
11
4
10
1.75
0.5
15.75
6
UPC
2
1
22
9
15
2
1
25
10
20
2
1
30
12.5
40
3.75
56
23
55
5
66
25
G.2.1.2 SE 1223LR Decode Zone
4,844 Lux to 86,112 Lux
Minimum
range
Width of field
Maximum
range
Width of field
Mil Size
Inches
Inches
Inches
Inches
10
11
2
24
5
High quality symbols in normal room light.
G-4
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix G: Specifications Scanners And Imagers
SE 1223HP, LR, ALR And SE 955HP Specifications
4,844 Lux to 86,112 Lux
Minimum
range
Width of field
Maximum
range
Width of field
Mil Size
Inches
Inches
Inches
Inches
15
7.5
1
39
8
20
7.5
1
48
10
40
10
2
90
19
55
10
2
120
24
70 reflective
48
200
40
100 reflective
60
240
48
High quality symbols in normal room light.
G.2.1.3 SE 1223ALR Decode Zone
4,844 Lux to 86,112 Lux
Minimum
range
Width of field
Maximum
range
Width of field
Inches
Inches
Inches
Inches
Mil Size
UPC
19
2
39
4
15
20
2
50
6
30
33
4
98
11
55
27
2
115
12
70 reflective
114
12
250
28
100 reflective
125
14
360
41
High quality symbols in normal room light.
G.2.1.4 SE 955HP Decode Zone
Decode Zone Typical
4 mil
1.0 in. - 5.5 in. / 2.54 cm - 13.97 cm
5 mil
1.25 in. - 8 in. / 3.18 cm - 20.32 cm
7.5 mil
1.5 in. - 13.25 in. / 3.81 cm - 33.66 cm
10 mil
1.5 in. - 17.5 in. / 3.81 cm - 44.45 cm
UPC 100%
1.5 in. - 23.5 in. / 3.81 cm - 59.69 cm
15 mil
1.5 in. - 29.5 in. / 3.81 cm - 74.93 cm
* dependent on width of bar code
Psion Teklogix WORKABOUT PRO HDK User Manual
G-5
Appendix G: Specifications Scanners And Imagers
Imager Specifications
Decode Zone Typical
20 mil
1.75 in. - 35.5 in. / 4.45 cm - 90.17 cm
40 mil
* - 40 in. / * - 101.6 cm
55 mil
* - 55 in. / * - 139.7 cm
* dependent on width of bar code
G.3
Imager Specifications
G.3.1
EV15 Imager Specifications
Parameter
EV15
Light Source
617nm Highly Visible LED
Scan Angle
40º
Minimum Print Contrast
Minimum 25%
Minimum x Dimension
0.1 mm (4 mils)
Reading Distance
Up to 90cm (35 in)
Symbologies
UPC (E&A), EAN, RSS, Code 39, Code 128,
UCC/EAN 128, ISBN, ISBT, Interleaved,
Matrix, Industrial and Standard 2 of 5, Codabar, Code 93/93i, Code 11, MSI, Plessey, Telepen, PDF417, Micro PDF417
Ambient Light
Works in any lighting conditions, from 0 to
100,000 lux
Shock
2000G, 0.7ms, half sinus, 3 axes
Vibration
50G r.m.s
G.3.1.1 EV15 Imager Decode Zone
0 Lux to 100,000 Lux
Minimum range
Maximum range
Inches
Inches
Mil Size
5
2.5
7
10
3
14
UPC
2
14.5
20
2.5
22
40
3
35.5
High quality symbols in normal room light.
G-6
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix G: Specifications Scanners And Imagers
HHP5180 Imager Specifications
G.3.2
HHP5180 Imager Specifications
Parameter
HHP5180
Image Sensor
752 X 480 CMOS sensor
Motion Tolerance
4 in. (10.2cm) per second
Rotational Sensitivity
360°
Viewing Angle
±40°
Ambient Light
Total darkness to 100,000 lux (full sunlight)
Illumination LEDs
626nm ±30nm
Aiming:
LEDs: 526nm ±30nm
Laser: 650nm ±10nm
Symbologies supported
2D: PDF417, MicroPDF417, MaxiCode, Data Matrix,
QR Code, Aztec, Aztec Mesa, Code 49, UCC Composite
Linear: Code 39, Code 128, Codabar, UPC, EAN, Interleaved 2 of 5, RSS, Code 93, Codablock
Postal: Postnet (US), Planet Code, BPO 4 State, Canadian Post, Japanese Post, KIX (Netherlands) Post
OCR Fonts: OCR-A, OCR-B
Size
1.78cm Depth x 2.79cm Width (without mounting tabs)
x 1.21cm Height
0.7 in. Depth x 1.1 in. Width (without mounting tabs) x
0.475 in. Height
Weight
5.9 grams (.21 ounces)
Operational Input Voltage:
Imager: 3.3 VDC ±5% (23°C)
Illumination + Aimer 5300: 3.0 VDC to 5.5 VDC (23°C)
Current Draw:
Imager: Operating Current: 100 mA
Standby Current: 100 µA
Operating Temperature
-30° to +50°C (-34° to 122°F)
Storage Temperature
-40° to +70°C (-40° to 158°F)
Humidity
up to 95% RH, non-condensing at 122° F (50°C)
Shock
18 shocks of 3,500 G for 0.5 msec at 23°C (73° F)
G.3.2.1 HHP5180 Imager Decode Zone
Performance
Focal Point
SR
7 inches (17.8 cm) from lens plate
SF
4.5 inches (11.4 cm) from lens plate
*Data characterized at 23°C and 0 lux ambient light.
Psion Teklogix WORKABOUT PRO HDK User Manual
G-7
Appendix G: Specifications Scanners And Imagers
SX5393 Imager Specifications
Performance
Focal Point
SR
Working
Range*
8.3 mil
Linear
(.020 cm)
10 mil
PDF417
(.025 cm)
13 mil
UPC
(.033
cm)
15 mil
Data
Matrix
(.038
cm)6
15 mil
QR
(.038
cm)
35 mil
Maxicode
(.089
cm)
Near
3.5 in.
(8.9 cm)
3.1 in.
(7.9 cm)
2.1 in.
(5.3cm)
2.3 in.
(5.8 cm)
2.1 in.
(7.9 cm)
2.0 in.
(5.1 cm)
Far
7.6 in.
(19.3cm)
9 in.
(22.9 cm)
13.2 in.
(33.5
cm)
10.2 in.
(25.9
cm)
8.8 in.
(22.4
cm)
13.0 in.
(33 cm)
SF
Working
Range*
6.6 mil
PDF417
(.017 cm)
7.5 mil
Linear
(.019 cm)
8.3 mil
Data
Matrix
(.021
cm)
8.3 mil
QR
(.021
cm)6
10 mil
Linear
(.025
cm)
13 mil
UPC
(.033
cm)
Near
2.8 in.
(7.1cm)
2.5 in.
(6.4cm)
3.4 in.
(8.6cm)
3.4 in.
(8.6cm))
2.2 in.
(5.6cm)
2.0 in.
(5.1cm)
Far
6 in.
(15.2cm)
6.5 in.
(16.5cm)
5.7 in.
(14.5cm)
5.4 in.
(13.7cm)
7.6 in.
(19.3cm)
8.9 in.
(22.6cm)
*Data characterized at 23°C and 0 lux ambient light.
G.3.3
SX5393 Imager Specifications
Parameter
SX5393
Optical Resolution
1024H x 1024V
Field of view at 6 inches
5.12 in. x 5.12 in.
Pitch Angle
±45°
Skew Angle
±45°
Ambient Light
0 to 100,000 lux (full sunlight) 300 lux nominal.
Minimum Contrast
10%
Targeting
Intuitive range finding 626 nm Red LED.
Self Illumination
Red LED
Supply Voltage
5 V ± 10%
Power Supply
3.6 Volt DC nominal (2.7 - 5 Volts DC)
Connectivity
USB 1.1 or serial async
Connector to the interface
board
Molex 52892-1295 or HiRose FH12-12S-.5SH
*Data characterized at 23°C and 0 lux ambient light.
G-8
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix G: Specifications Scanners And Imagers
SX5393 Imager Specifications
Parameter
SX5393
Symbologies Supported
Code 39; Code 39 Full ASCII; UPC-A, -A2, -A5; UPCE, -E2, -E5; EAN-8 -13; JAN; I2of5; Code 128; Codabar/NW7; RSS 14, RSS Limited, RSS Expanded, RSS
14 Truncated, PDF417, microPDF417; Composite, CCA, CC-B, CC-C; image capture and signature capture,
Data Matrix; QR Code; Maxicode; Aztec Code; Planet;
Postnet; Royal Mail 4SCC; 4 State postal codes from
Australia, Canada, Japan; Korean Post 3of5
Operating Temperature
-20° to +50°C (-4° to 122°F)
Storage Temperature
-30° to +60°C (-22° to 140°F)
Humidity
5% to 95% (non-condensing)
Weight
Image engine 4.1 grams
Co-processor board 6.80 grams
Shock
15 drops, 5 ft to concrete at room temperature when
integrated correctly into end-user packaging
*Data characterized at 23°C and 0 lux ambient light.
G.3.3.1 SX5393 Imager Decode Zone
2D Bar Codes
300 Lux With Good Quality Bar Codes
Mil Size*
Minimum range
Maximum range
Inches
Inches
10
4.6
5.7
15
3.8
9.2
15**
4
9.7
20.8
2.6
11.7
*QR code
**Data Matrix
Psion Teklogix WORKABOUT PRO HDK User Manual
G-9
Appendix G: Specifications Scanners And Imagers
SX5400 Imager Specifications
1D Bar Codes
300 Lux With Good Quality Bar Codes
Minimum range
Maximum range
Inches
Inches
Mil Size
G.3.4
Code 39
Minimum range
Maximum range
Mil Size
Inches
Inches
7.5
4.1
8.4
10
3.1
10.9
15
4
9.7
SX5400 Imager Specifications
Parameter
G-10
SX5400
Optical Resolution
752H x 480V
Field of view at 160mm
120mm (H) x 78mm (V)
41.1° (H) x 27.4° (V)
Pitch angle
±45°
Skew angle
±45°
Ambient light
0 to 100,000 lux (full sunlight
300 lux nominal
Minimum contrast
10%
Targeting
Intuitive range finding 626 nm LED
Self Illumination
Red LED (standard)
White LED (optional)
Supply voltage
5 V ± 10%
Power supply
3.6 Volt DC nominal (2.7 - 5 Volts DC)
Connectivity
USB 1.1 or serial async
Connector to the interface board
Molex 52892-1295 or HiRose FH12-12S.5SH
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix G: Specifications Scanners And Imagers
SX5400 Imager Specifications
Parameter
SX5400
Symbologies supported
Code 39; Code 39 Full ASCII; UPC-A,
-A2, -A5; UPC-E, -E2, -E5; EAN-8 -13;
JAN; I2of5; Code 128; Codabar/NW7; RSS
14, RSS Limited, RSS Expanded, RSS 14
Truncated, PDF417, microPDF417; Composite, CC-A, CC-B, CC-C; image capture
and signature capture, Data Matrix; QR
Code; Maxicode; Aztec Code; Planet; Postnet; Royal Mail 4SCC; 4 State postal codes
from Australia, Canada, Japan; Korean Post
3 of 5.
Operating temperature
-20° to 50 °C (-4° to 122°F)
Storage temperature
-30° to 60°C (-22° to 140°F)
Relative humidity
5% to 95% (non-condensing)
Weight
Image engine 4.1 grams
Co-processor board 6.80 grams
Shock
15 drops, 5 ft to concrete at room temperature when integrated correctly into enduser packaging.
G.3.4.1 SX5400 Imager Decode Zone
Symbology
Size (mil)
Minimum
(inches)
Maximum
(inches)
Average Depth Of Reading
(inches)
C39
7.5
4.0
7.0
3.0
C39
10
2.75
9.25
6.5
C39
15
2.25
11.0
8.75
PDF6.6
6.6
4.0
6.5
2.5
PDF10
10
3.25
9.0
5.75
PDF15
15
2.25
10.75
8.5
DM15
15
3.0
8.0
5.0
QR15
15
3.75
7.5
3.75
UPC
12.5
3.0
9.5
6.5
Typical performance at 300 lux for the SX5400 @160mm focus
Psion Teklogix WORKABOUT PRO HDK User Manual
G-11
H
APPENDIX
SPECIFICATIONS WORKABOUT PRO BATTERIES
H.1 Battery Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
H.2 Standard Capacity–2000 mAh (Model WA3000-G1)
H.2.1 Electrical Specifications . . . . . . . . . .
H.2.2 Standard Discharge . . . . . . . . . . . . .
H.2.3 Environmental Test . . . . . . . . . . . . .
H.3 High-Capacity 3000mAh (Model WA3006) . . . . .
H.3.1 Electrical Specifications . . . . . . . . . .
H.3.2 Standard Discharge . . . . . . . . . . . . .
H.3.3 Safety Data . . . . . . . . . . . . . . . . .
H.3.4 Safety License . . . . . . . . . . . . . . .
H.3.5 Environmental Test . . . . . . . . . . . . .
H.4 Super High-Capacity (Model WA3010) . . . . . . .
H.4.1 Electrical Specifications . . . . . . . . . .
H.4.2 Standard Discharge . . . . . . . . . . . . .
H.4.3 Safety Data . . . . . . . . . . . . . . . . .
H.4.4 Safety License . . . . . . . . . . . . . . .
H.4.5 Environmental Test . . . . . . . . . . . . .
H.5 Maxell ML2032 Rechargeable Coin Battery . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 3
. 3
. 4
. 5
. 6
. 6
. 7
. 8
. 8
. 8
. 9
. 9
10
11
12
12
13
H.6 WORKABOUT PRO 2nd. Generation (C And S) Internal Battery . . . . . . . . . . . . . . . . . . 13
Psion Teklogix WORKABOUT PRO HDK User Manual
H-1
Appendix H: Specifications WORKABOUT PRO Batteries
Battery Specifications
H.1
Battery Specifications
Note: Performance specifications are nominal & subject to change without notice.
Consult the Accessories Catalog at www.PsionTeklogix.com/Accessories to ensure that a
specific device is still available.
This appendix describes all the batteries that are available in the following WORKABOUT PRO
variants:
• WORKABOUT PRO C
• WORKABOUT PRO S
• WORKABOUT PRO ME
• WORKABOUT PRO 2nd. Generation C
• WORKABOUT PRO 2nd. Generation S
Consult the specifications for your WORKABOUT PRO to find out which batteries are
compatible with it.
H.2
Standard Capacity–2000 mAh (Model WA3000-G1)
H.2.1
Electrical Specifications
Note: The electrical specifications apply for ambient temperature TAMB of 0° to +40°C unless
otherwise stated.
Description
Specification
Remark
Interface Chipset
Maxim DS2762
-
Rated Voltage
3.7V
Typical
Rated Capacity
2000mAh
Typical
Rated Charge Current
1.0A
Maximum
Charge Voltage
4.2 +/- 0.05V
Maximum
Discharge Cut-off voltage
2.6V
Typical
Charge Method
Constant voltage
Current limited
-
Discharge Current
0.5C (-20°C to 60°C)
Typical
Internal Resistance
150 mΩ
Maximum
Battery Pack Electrical Specifications
Description
Specification
Minimum
Typical
Maximum
Over voltage detection
voltage
4.325V
4.350V
4.375V
Charge enable
4.10V
4.15V
4.20V
Under voltage detection
voltage
2.5V
2.6V
2.7V
Psion Teklogix WORKABOUT PRO HDK User Manual
H-3
Appendix H: Specifications WORKABOUT PRO Batteries
Standard Discharge
H.2.2
Description
Specification
Over current detection
current
2.97A
3.17A
3.36A
Short-circuit detection
current
9.9A
13.33A
16.83A
Short-circuit detection
voltage
150mV
200mV
250mV
Over voltage delay time
0.8s
1s
1.2s
Under voltage delay time
90ms
100ms
110ms
Over current delay time
5ms
10ms
20ms
Short-circuit delay time
160µs
200µs
240µs
Recovery charge current
0.5mA
1mA
2mA
Standard Discharge
Note: Standard charge is defined as charging with constant voltage limit of 4.2V and constant
current limit of 0.9A; the termination charge occurs when the current drops to 45mA.
Standard discharge is defined as discharging at a constant current of 350mA until the
battery protection circuit switches the battery output off in over-discharge mode.
Acceptance Test Specifications
H-4
Description
Condition
Standard
Open circuit
voltage
After standard charge, measured within
24 hours.
4.15V or more
Internal resistance
After standard charge, measured within
24 hours.
150 mΩ max.
Capacity_1
After standard charge, measured time taken
for a fast discharge.
110 minutes or more
Charge/Discharge
cycle
After repeating standard charge and fast discharge, measured the fast discharge time after
300 discharge cycles.
90 minutes or more
Capacity_2
After standard charge, measured the time
taken for a standard discharge.
500 minutes or more
Over discharge
After standard charge, apply a standard discharge followed by a standby discharge. Then
measured capacity after carrying out standard
charge and then a fast discharge.
110 minutes or more
Self discharge
After a standard charge, keep battery at 25°C
for 30 days. Measured the time taken for a
fast discharge.
100 minutes or more
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix H: Specifications WORKABOUT PRO Batteries
Environmental Test
H.2.3
Description
Condition
Standard
Temperature
Perform a standard charge and fast discharge
at 0°C, 25°C and 40°C and measured the time
taken for a fast discharge at 25°C.
100 minutes @ 0°C
110 minutes @ 23°C
105 minutes @ 40°C
Temperature/Humidity
cycle
After standard charge, carry out 5 cycles:
65°C and 90% humidity for 8 hrs.
25°C and 65% humidity for 4 hrs.
-20°C for 8 hrs. 25°C and 65% humidity for
4 hrs.
100 minutes or more
Dry heat
After standard charge, keep the battery at
60°C for 8 hrs. Carry out a fast discharge,
standard charge and then a fast discharge,
measured the time taken for the second discharge.
100 minutes or more
Electro-Static Discharge
EN61000-4-8:
A. Contact Discharge:+/- 8kV for each
contact pad by 10 times.
B. Air Discharge:+/- 15kV for 10 times.
No damage
Environmental Test
Description
Test Reference
Test Condition/Result
Drop
(mechanical)
Drop sample battery on all faces from
height of 1.2 meters onto concrete
floor
No explosion, fire, vent, leakage and
open circuit voltage higher than 3.7V.
Storage at high temp.
EN60068-2-2 Test
+60°C dry for 240 hours
No explosion, fire, vent or leakage.
Storage at low temp.
EN60068-2-1 Test
-20°C dry for 240 hours
No explosion, fire, vent or leakage.
Storage at high temp.
and humidity
IEC68-2-3 Test
+40°C at 90%RH for 240 hours.
No explosion, fire, vent or leakage.
Storage temp. cycling
IEC68-2-14 Test
+60°C (2C) for 1 hr. (T1), -20°C (2C)
for 1 hr. 3 mins. maximum allows for
change between T1 and T2, 10 cycles.
No explosion, fire, vent or leakage.
Vibration resistance
BS2011 Part 2.1
FDC (IEC68-2-37)
After standard charge, tested under the
following conditions: Random vibration 5Hz-500Hz ASD 0.02g2/Hz in 3
axis for 15 mins. Followed by standard discharge, charge, discharge. No
parting joints/cracks or damage to
connectors. No leakage or
critical damage.
Psion Teklogix WORKABOUT PRO HDK User Manual
H-5
Appendix H: Specifications WORKABOUT PRO Batteries
High-Capacity 3000mAh (Model WA3006)
Description
Test Reference
Test Condition/Result
Impact shock resistance
-
3 cycles of 50G 11ms, 1/2 sine pulse
acceleration applied in 6 directions. 18
shocks total.
ESC protection
-
Accordance with EN61000-4-8
H.3
High-Capacity 3000mAh (Model WA3006)
H.3.1
Electrical Specifications
Note: The electrical specifications apply for ambient temperature TAMB of 0° to +40°C unless
otherwise stated.
Item
Description
Specification
Remark
1
Interface Chipset
Maxim DS2762
-
2
Rated Voltage
3.7V
Typical
3
Rated Capacity
3000mAh
Typical
4
Rated Charge Current
1.5A
Maximum
5
Charge Voltage
4.2 +/- 0.05V
Maximum
6
Discharge Cut-off voltage
2.6V
Typical
7
Discharge Current
Constant voltage
Current limited
-
8
Discharge Current
0.5C (-20°C to 60°C)
Typical
9
Internal Resistance
200 mΩ
Maximum
Battery Pack Electrical Specifications
Description
H-6
Specification
Minimum
Typical
Maximum
Over voltage detection voltage
4.325V
4.350V
4.375V
Charge enable
4.10V
4.15V
4.20V
Under voltage detection voltage
2.5V
2.6V
2.7V
Over current detection current
-
3.5A
-
Short-circuit detection current
5.0A
8.0A
11.0A
Short-circuit detection voltage
150mV
200mV
250mV
Over voltage delay time
0.8s
1s
1.2s
Under voltage delay time
90ms
100ms
110ms
Over current delay time
5ms
10ms
20ms
Short-circuit delay time
160µs
200µs
240µs
Recovery charge current
0.5mA
1mA
2mA
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix H: Specifications WORKABOUT PRO Batteries
Standard Discharge
H.3.2
Standard Discharge
Note: Standard charge is defined as charging with constant voltage limit of 4.2V and constant current limit of 0.9A; the termination charge occurs when the current drops to 45mA.
Standard discharge is defined as discharging at a constant current of 350mA until the battery protection circuit switches the battery output off in over-discharge mode.
Acceptance Test Specifications
Description
Condition
Standard
Open circuit
voltage
After standard charge, measure within
24 hours.
4.15V or more
Internal Resistance
After standard charge, measure within
24 hours.
200 mΩ max.
Capacity_1
After standard charge, measure time taken for
a fast discharge.
110 minutes or more
Charge/Discharge
Cycle
After repeating standard charge and fast discharge, measure the fast discharge time after
300 discharge cycles.
90 minutes or more
Capacity_2
After standard charge, measure the time taken
for a standard discharge.
500 minutes or more
Over Discharge
After standard charge, apply a standard discharge followed by a standby discharge. Then
measure capacity after carrying out standard
charge and then a fast discharge.
110 minutes or more
Self discharge
After a standard charge, keep battery at 25°C
for 30 days. Measure the time taken for a
fast discharge.
100 mins or more
Temperature
Perform a standard charge and fast discharge
at 0°C, 25°C and 40°C and measured the time
taken for a fast discharge at 25°C.
100 minutes @ 0°C
110 minutes @ 23°C
105 minutes @ 40°C
Temp./Humidity
Cycle
After standard charge, carry out 5 cycles of the
following: 65°C and 90% humidity for 8 hrs.
25°C and 65% humidity for 4 hrs.
-20°C for 8 hrs. 25°C and 65% humidity for
4 hrs.
Following that, perform a fast discharge,
standard charge and then a fast discharge.
Measure the time taken for the
second discharge.
100 minutes or more
Dry heat
After standard charge, keep the battery at 60°C
for 8 hrs. Carry out a fast discharge, standard
charge and then a fast discharge, measured the
time taken for the second discharge.
100 minutes or more
Psion Teklogix WORKABOUT PRO HDK User Manual
H-7
Appendix H: Specifications WORKABOUT PRO Batteries
Safety Data
H.3.3
H.3.4
H.3.5
H-8
Description
Condition
Standard
EMC/CE Testing
The battery will need to pass the requirements
of the EMC directive 89/336/EEC (and
amendments) when fitted into the product:
Emissions to EN55022 Class B (1998) Immunity to EN55024 (1998)
Test to be performed
by manufacturer.
Electro-Static Discharge Test
EN61000-4-8:
A. Contact Discharge: +/-8kV for each contact
pad by 10 times.
B. Air Discharge: +/-15kV for 10 times (the
discharge test point is for around battery casing.)
No damage
Safety Data
Description
Condition
Test Condition/Result
Short Circuit Test
After a standard charge,
short terminals and discharge for 1 hr.
Protection circuit board to operate.
No explosion, fire, smoke,
or leakage.
Over Charging Test
After a standard charge,
charge continuously at 4.2V
and 4A for 8 hrs.
Protection circuit board to operate.
No explosion, fire, smoke,
or leakage.
Reverse Charging
Test
After a standard discharge,
reverse-charge continuously
at 4.2V and 4A for 8hrs.
Protection circuit board to operate.
No explosion, fire, smoke,
or leakage.
Safety License
Item
License
Standard
1
UL 1642
The lithium-ion cell has been listed and pass the
UL1642 standard by UL Lab.
2
UL 2054
The battery pack is in the process to apply the UL 2054
battery standard.
3
89/336 EEC-EMC
directive.
The battery pack is in the process to apply this standard:
-EN55022 -LVD 72/23 EEC -EN55024 -EN61326
4
RoHS Directive
The battery pack is in the process to apply the RoHS
directive applicable report by SGS Lab.
Environmental Test
Description
Test Reference
Test Condition/Result
Drop
(mechanical)
Drop sample battery on all faces from
height of 1.2 meters onto concrete floor.
No explosion, fire, vent, leakage and the
open circuit voltage higher than 3.7V.
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix H: Specifications WORKABOUT PRO Batteries
Super High-Capacity (Model WA3010)
Description
Test Reference
Test Condition/Result
Storage at high
temp.
EN60068-2-2 Test
+60°C dry for 240 hours
No explosion, fire, vent or leakage.
Storage at low
temp.
EN60068-2-1 Test
-20°C dry for 240 hours
No explosion, fire, vent or leakage.
Storage at high
temp. and high
humidity
IEC68-2-3 Test
+40°C at 90%RH for 240 hours.
No explosion, fire, vent or leakage.
Storage temp.
cycling
IEC68-2-14 Test
+60oC (2C) for 1 hour (T1), -20oC (2C)
for 1 hour. 3 minutes Max allowed for
change between T1 and T2.
Cycle 10 times
No explosion, no fire, no vent, and
no leakage.
Vibration resistance
BS2011 Part 2.1
FDC (IEC68-2-37)
After standard charge, tested under the following conditions: Random vibration 5Hz500Hz ASD 0.02g2/Hz in 3 axis for 15
mins. After which, carry out a standard
discharge, charge, discharge. No parting
joints/cracks or damage to connectors. No
leakage or critical damage.
Impact shock
resistance
-
3 cycles of 50G 11ms, 1/2 sine pulse acceleration applied in 6 directions. 18
shocks total.
ESD protection
-
Accordance with EN61000-4-8
H.4
Super High-Capacity (Model WA3010)
H.4.1
Electrical Specifications
Note: The electrical specifications apply for ambient temperature TAMB of 0° to +40°C unless
otherwise stated.
Item
Description
Specification
Remark
1
Interface Chipset
Maxim DS2762
-
2
Rated Voltage
3.7V
Typical
3
Rated Capacity
4000mAh
Typical
4
Rated Charge Current
1.2A
Maximum
5
Charge Voltage
4.2 +/- 0.05V
Maximum
6
Discharge Cut-Off Voltage
2.6V
Typical
7
Charge Method
Constant voltage
Current limited
-
8
Discharge Current
0.5C (-20°C to 60°C)
Typical
Psion Teklogix WORKABOUT PRO HDK User Manual
H-9
Appendix H: Specifications WORKABOUT PRO Batteries
Standard Discharge
Item
Description
Specification
Remark
9
Internal Resistance
150 mΩ
Maximum
10
Charging Temperature
0 to 40
Typical
Battery Pack Electrical Specifications
Item
H.4.2
Description
Specification
Minimum
Typical
Maximum
1
Over voltage detection voltage
4.325V
4.350V
4.375V
2
Charge enable
4.10V
4.15V
4.20V
3
Under voltage detection
voltage
2.5V
2.6V
2.7V
4
Over current detection current
2.97A
3.17A
3.36A
5
Short-circuit detection current
9.9A
13.33A
16.83A
6
Short-circuit detection voltage
150mV
200mV
250mV
7
Over voltage delay time
0.8s
1s
1.2s
8
Under voltage delay time
90ms
100ms
110ms
9
Over current delay time
5ms
10ms
20ms
10
Short-circuit delay time
160µs
200µs
240µs
11
Recovery charge current
0.5mA
1mA
2mA
Standard Discharge
Note: Standard charge is defined as charging with constant voltage limit of 4.2V and constant
current limit of 0.9A; the termination charge occurs when the current drops to 45mA.
Standard discharge is defined as discharging at a constant current of 350mA until the
battery protection circuit switches the battery output off in over-discharge mode.
Acceptance Test Specifications
H-10
Description
Condition
Standard
Open circuit
voltage
After standard charge, measure within
24 hours.
4.15V or more
Internal Resistance
After standard charge, measure within
24 hours.
150 mΩ max.
Capacity_1
After standard charge, measure time taken for
a fast discharge.
110 minutes or more
Charge/Discharge
Cycle
After repeating standard charge and fast discharge, measure the fast discharge time after
300 discharge cycles.
90 minutes or more
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix H: Specifications WORKABOUT PRO Batteries
Safety Data
H.4.3
Description
Condition
Standard
Capacity_2
After standard charge, measure the time taken
for a standard discharge.
500 minutes or more
Over Discharge
After standard charge, apply a standard discharge followed by a standby discharge. Then
measure capacity after carrying out standard
charge and then a fast discharge.
110 minutes or more
Self discharge
After a standard charge, keep battery at 25°C
for 30 days. Measure the time taken for a
fast discharge.
100 minutes or more
Temperature
Perform a standard charge and fast discharge
at 0°C, 25°C and 40°C and measured the time
taken for a fast discharge at 25°C.
100 minutes @ 0°C
110 minutes @ 23°C
105 minutes @ 40°C
Temp./Humidity
Cycle
After standard charge, carry out 5 cycles of the
following: 65°C and 90% humidity for 8 hrs.
25°C and 65% humidity for 4 hrs.
-20°C for 8 hrs. 25°C and 65% humidity for
4 hrs.
Following that, perform a fast discharge,
standard charge and then a fast discharge.
Measure the time taken for the
second discharge.
100 minutes or more
Dry heat
After standard charge, keep the battery at 60°C
for 8 hrs. Carry out a fast discharge, standard
charge and then a fast discharge. Measure the
time taken for the second discharge.
100 minutes or more
EMC/CE Testing
The battery will need to pass the requirements
of the EMC directive 89/336/EEC (and
amendments) when fitted into the product:
Emissions to EN55022 Class B (1998)
Immunity to EN55024 (1998).
Test to be performed
by manufacturer.
Electro-Static
Discharge Test
EN61000-4-8:
A. Contact Discharge: +/-8kV for each contact
pad by 10 times.
B. Air Discharge: +/-15kV for 10 times (the
discharge test point is for around
battery casing.)
No damage
Safety Data
Description
Condition
Test Condition/Result
Short Circuit Test
After a standard charge,
short terminals and discharge for 1 hr.
Protection circuit board to operate.
No explosion, fire, smoke,
or leakage.
Psion Teklogix WORKABOUT PRO HDK User Manual
H-11
Appendix H: Specifications WORKABOUT PRO Batteries
Safety License
H.4.4
H.4.5
H-12
Description
Condition
Test Condition/Result
Over Charging Test
After a standard charge,
charge continuously at 4.2V
and 4A for 8 hrs.
Protection circuit board to operate.
No explosion, fire, smoke,
or leakage.
Reverse Charging
Test
After a standard discharge,
reverse-charge continuously
at 4.2V and 4A for 8hrs.
Protection circuit board to operate.
No explosion, fire, smoke,
or leakage.
Safety License
Item
License
Standard
1
UL 1642
The lithium-ion cell has been listed and pass the
UL1642 standard by UL Lab. File No. MH12383
2
UL 2054
The battery pack is in the process to apply the UL 2054
battery standard. File No. MH29921.
3
89/336 EEC-EMC
directive
The battery pack is in the process to apply this standard:
-EN55022 -LVD 72/23 EEC -EN55024 -EN61326
4
RoHS Directive
The materials of battery pack are used in accordance
with the European RoHS directive.
Environmental Test
Description
Test Reference
Test Condition/Result
Drop
(mechanical)
Drop sample battery on all faces from
height of 1.2 meters onto concrete floor.
No explosion, fire, vent, leakage and the
open circuit voltage higher than 3.7V.
Storage at high
temp.
EN60068-2-2 Test
+60°C dry for 240 hours
No explosion, fire, vent or leakage.
Storage at low
temp.
EN60068-2-1 Test
-20°C dry for 240 hours
No explosion, fire, vent or leakage.
Storage at high
temp. and high
humidity
IEC68-2-3 Test
+40°C at 90%RH for 240 hours.
No explosion, fire, vent or leakage.
Storage temp.
cycling
IEC68-2-14 Test
+60°C (2C) for 1 hour (T1), -20oC (2C)
for 1 hour. 3 minutes Max allowed for
change between T1 and T2.
Cycle 10 times
No explosion, no fire, no vent, and
no leakage.
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix H: Specifications WORKABOUT PRO Batteries
Maxell ML2032 Rechargeable Coin Battery
H.5
Description
Test Reference
Test Condition/Result
Vibration resistance
BS2011 Part 2.1
FDC (IEC68-2-37)
After standard charge, tested under the following conditions: Random vibration 5Hz500Hz ASD 0.02g2/Hz in 3 axis for 15
mins. After which, carry out a standard
discharge, charge, discharge. No parting
joints/cracks or damage to connectors. No
leakage or critical damage.
Impact shock
resistance
-
3 cycles of 50G 11ms, 1/2 sine pulse acceleration applied in 6 directions. 18
shocks total.
ESD protection
-
Accordance with EN61000-4-8
Maxell ML2032 Rechargeable Coin Battery
Model
ML2032
System
Lithium Ion
Nominal Voltage (V)
3V
Nominal Capacity (mAh*)
65
Nominal Discharge Current
(µA)
200
Depth of Discharge = 10%
1,000 (6.5 mAh discharge) (total capacity 6,500 mAh)
Depth of Discharge = 20%
300 (13 mAh discharge) (total capacity 3,900 mAh)
Temperature Ranges
Operating
-10° C to 60° C (14° F to 140° F)
*Nominal capacity indicates duration until the voltage drops down to 2.0V when discharged at a
nominal discharge current at 20° C (68° F).
H.6
WORKABOUT PRO 2nd. Generation (C And S) Internal Battery
System
Lithium Ion
Nominal Voltage (V)
3.7 V
Nominal Capacity (mAh*)
140 mAh typical, 130 mAh minimum.
Maximum continuous
discharge current
260 mA
Operating Temperature
Range
-20° C to 60° C (-4° F to 140° F)
Charging Temperature
Range
0° C to 45° C (32° F to 113° F)
Psion Teklogix WORKABOUT PRO HDK User Manual
H-13
APPENDIX
I
HARDWARE DEVELOPER KIT LICENSE AGREEMENT
I.1 HARDWARE DEVELOPER KIT LICENSE AGREEMENT . . . . . . . . . . . . . . . . . . . . . I-3
I.2 GRANT OF LICENSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-3
I.3 DESCRIPTION OF REQUIREMENTS, RESTRICTIONS, RIGHTS AND LIMITATIONS . . . . . I-3
I.4 HIGH RISK ACTIVITIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-4
I.5 DISCLAIMER OF WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-4
I.6 LIMITATION OF LIABILITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-4
I.7 COPYRIGHTS, OWNERSHIP AND PROPRIETARY RIGHTS . . . . . . . . . . . . . . . . . . . I-4
I.8 CONFIDENTIALITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-5
I.9 ENDING THIS AGREEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-5
I.10 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-5
Psion Teklogix WORKABOUT PRO HDK User Manual
I-1
Appendix I: Hardware Developer Kit License Agreement
HARDWARE DEVELOPER KIT LICENSE AGREEMENT
I.1
HARDWARE DEVELOPER KIT LICENSE AGREEMENT
IMPORTANT - READ CAREFULLY:
This Hardware Developer Kit License Agreement (“Agreement”) is a legal agreement between
you and Psion Teklogix (“we”), the licensor of Psion Teklogix Hardware Developer Kit (“HDK”)
which is downloaded from the Psion Teklogix website, for developers of hardware expansion
modules intended to be used with the Psion Teklogix handheld mobile devices.
By clicking on the “Accept” or other appropriate assent button and/or installing the HDK, you
agree to be and are hereby bound by the terms and conditions of this Agreement. If you do not
agree with this Agreement, we do not grant you a license to the HDK, and you may not install or
use the HDK or any accompanying documentation.
The HDK is the property of Psion Teklogix Inc. or its licensors and is protected by copyright laws
and international copyright treaties, as well as other intellectual property laws and treaties. The
HDK is licensed, not sold. Psion Teklogix Inc. provides the HDK and licenses its use worldwide.
You assume responsibility for the selection of the HDK to achieve your intended results, and for
the use and results obtained from it.
I.2
GRANT OF LICENSE
We hereby grant you and you hereby accept a non-exclusive, non-transferable, royalty-free license
to use the HDK to develop hardware expansion modules to be used with the Psion Teklogix handheld mobile devices subject to the terms and restrictions set forth in this Agreement. Except as
explicitly set forth below, (i) you are not permitted to sell, lease or rent, distribute or sublicense the
HDK or to use the HDK in a time-sharing arrangement or in any other unauthorized manner; (ii)
no license is granted to you in the human readable code of the HDK (source code); and (iii) this
Agreement does not grant you any rights to patents, copyrights, trade secrets, trademarks, intellectual property or any other ownership rights with respect to the HDK.
The HDK is licensed to be used on any personal computer and/or Psion Teklogix handheld mobile
devices, provided that the HDK is used only in connection with your development of hardware expansion modules for use and compatible with the Psion Teklogix handheld mobile devices (the
“Expansion(s)”). The HDK contains certain documentation, drawings, programs, files, specifications, datasheets and APIs. You may distribute the HDK in object code format solely as part of
your Expansion. The HDK shall be distributed to your customers under the terms of your standard
end user license agreement, provided it includes terms that are substantially similar to those described herein. You are required to include Psion Teklogix' copyright notices on your Expansion
that includes the HDK.
I.3
DESCRIPTION OF REQUIREMENTS, RESTRICTIONS, RIGHTS AND
LIMITATIONS
a.Distribution. Except as provided for in this Agreement, you may not distribute the HDK, in
whole or in part, to any other third party.
b.Virus Program. You may not develop or knowingly incorporate any virus program that may be
harmful to a computer or a network in conjunction with the HDK, or use the HDK for any other
purpose as which may be harmful to a third party.
c.Assignment. You may not assign or transfer the HDK to a third party or allow a third party to use
the same.
d.Reverse Engineering. Modification, reverse engineering, reverse compiling, or disassembly of
the HDK is expressly prohibited.
Psion Teklogix WORKABOUT PRO HDK User Manual
I-3
Appendix I: Hardware Developer Kit License Agreement
HIGH RISK ACTIVITIES.
e.Export Restrictions. You agree that you will not export or re-export the HDK, or any part or
copies thereof, or any products utilizing the HDK in violation of applicable laws or regulations of
the United States or the country in which you obtained them.
I.4
HIGH RISK ACTIVITIES.
The HDK is not fault-tolerant and is not designed, manufactured or intended for use or resale as
on-line control equipment in hazardous environments requiring fail-safe performance, such as in
the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct life support machines, or weapons systems, in which the failure of the HDK could lead
to death, personal injury, or severe physical or environmental damage (“High Risk Activities”).
We specifically disclaim any express or implied warranty of fitness for High Risk Activities.
I.5
DISCLAIMER OF WARRANTY
We do not warrant uninterrupted or error free operation of the HDK nor do we warrant that the
HDK will meet your requirements. THE HDK AND DOCUMENTATION ARE PROVIDED
“AS-IS” WITHOUT ANY WARRANTY WHATSOEVER AND WITHOUT ANY TECHNICAL SUPPORT OF ANY KIND. WE DISCLAIM ANY AND ALL REPRESENTATIONS,
WARRANTIES AND CONDITIONS, WHETHER EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABLE QUALITY OR FITNESS FOR A PARTICULAR PURPOSE. WE DO NOT
WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE
RESULTS OF THE USE OF THE HDK IN TERMS OF ITS CORRECTNESS, ACCURACY,
RELIABILITY, USE WITH FUTURE PSION TEKLOGIX DEVICES INTRODUCED, OR
OTHERWISE. YOU EXPRESSLY ACKNOWLEDGE AND AGREE THAT USE AND MODIFICATION OF THE HDK IS AT YOUR SOLE RISK AND YOU ARE RESPONSIBLE FOR
INSTALLATION AND MODIFICATION OF THE HDK ON YOUR COMPUTER.
I.6
LIMITATION OF LIABILITY
Under no circumstances are we or our third party suppliers liable for damages of third parties
claimed against you, or for harm to your records or data, or special, incidental, indirect, or consequential damages, including but not limited to lost profits, lost business revenue or failure to
realize expected savings, loss of data, loss of use of the HDK or any associated equipment, downtime and user's time, even if you informed us of their possibility, or for breach of any express or
implied warranty, breach of contract, negligence, strict liability or any other legal theory related to
the HDK. This limitation applies whether you are entitled to claim damages from us or our third
party suppliers as a matter of contract or tort.
I.7
COPYRIGHTS, OWNERSHIP AND PROPRIETARY RIGHTS
All title and copyrights in and to the HDK, and any copies thereof, are owned by Psion Teklogix
Inc. or its suppliers. The HDK also contains copyrighted material licensed from our suppliers and
all rights to such copyrighted material rests with such suppliers. We retain title to the HDK and any
copies made from it. Any copies of the HDK you made are subject to the restrictions of this
Agreement.
WE DISCLAIM ALL WARRANTIES AND INDEMNITIES, EXPRESS, IMPLIED OR STATUTORY, FOR PATENT OR COPYRIGHT INFRINGEMENT.
I-4
Psion Teklogix WORKABOUT PRO HDK User Manual
Appendix I: Hardware Developer Kit License Agreement
CONFIDENTIALITY
I.8
CONFIDENTIALITY
You agree not to use or disclose any proprietary information provided by us, except for the purposes of this Agreement. You agree not to reproduce any of the copyrighted materials unless
expressly permitted by this Agreement.
I.9
ENDING THIS AGREEMENT
We may terminate this Agreement and your license immediately without notice if (a) you fail to
comply with any term of this Agreement, or (b) your rights are assigned by you, by operation of
law or otherwise. In such event, you must return or destroy all copies and component parts of the
HDK and documentation, as well as any other Psion Teklogix proprietary information in your possession, within fourteen (14) days of the date of termination. Any rights and obligations under this
Agreement that by their nature continue after it ends, will remain in effect until they are
completed.
I.10
GENERAL
The laws of the Province of Ontario and the federal laws applicable therein, excluding the conflict
of laws provisions, govern this Agreement. If any provision of this Agreement is deemed invalid
or unenforceable by any country, that particular provision will be deemed modified to the extent
necessary to make the provision valid and enforceable, and the remaining provisions will remain
in full force and effect. Failure by us to insist on strict performance or to exercise a right when entitled, does not prevent us from doing so at a later time, either in relation to that default or any
subsequent one.
No modifications of this Agreement shall be effective unless in writing and approved by us.
You acknowledge that you have read this Agreement, understand it, and that it is the complete
agreement between you and Psion Teklogix with respect to the subject matter hereof and supersedes all prior agreements, oral or written.
Psion Teklogix WORKABOUT PRO HDK User Manual
I-5
INDEX
A
address bus
in expansion module connection 70
addresses
for expansion EEPROM 74
on I2C bus 73
approvals
WORKABOUT PRO (including scanner) 4, 6
audio controller 13, 15
B
backplate
IP sealing for 35
models 35
weight 35
backup battery 16
batteries 16
specifications 7
battery specifications 8
high-capacity (WA3006) 8, 6
super high-capacity (WA3010) 8, 9
battery switching 16
battery threshold 16
battery threshold voltage 16
block diagram
docking station 49
LIF connector and cradle 53, 55
LIF connector and quad cradle 52
Bluetooth specs 5
buffer direction signals
and PCMCIA Expansion Module 103
buffer enable signals
and PCMCIA Expansion Module 103
bus
data and address on expansion connector 70
I2C 73
C
cable
flex for scanner module 85
scanner flex 85
Card Detect signals
and PCMCIA Expansion Module 103
card stop
location and dimensions 36
card types
accepted by PCMCIA Expansion Module 102
CN3
connector on scanner converter board 96
COM port
on scanner connector 87
COM ports
defailt 24
configuration
of Multi-I/O Expansion Module 113
connector
on Multi-I/O Expansion Module
for FF UART serial 110
for power and ground 113
for scanner 109
for scanner serial 109
for USB Host 1 112
for USB Host 2 110
for 100-pin bus 109
on PCMCIA Expansion Module 101
on scanner converter board
for flex cable from WORKABOUT PRO 92
for scan engine 94
connector locations
C, M, and ME 17
S 17
2nd. generation C and S 18
connectors
of Multi-I/O Expansion Module 108
contents of HDK 4
control signals
for FFUART level conversion
enabling jumper on Multi-I/O Expansion Module
117
cradle
block diagram of 53, 55
D
data bus
in expansion module connection 70
data bus buffer 103
data format
for expansion EEPROM 75
default COM ports 24
dimensions
card stop 36
docking station
block diagram of 49
driver
COM port 21
non-Psion Teklogix 21
PCMCIA 21
PCO 21
peripheral control 21
serial port 21
drivers 21
Windows Mobile 6 21
DSSS, 802.11b/g radio 3
E
EEPROM
addresses for 74
circuit in expansion module 74
data format for 75
in Multi-I/O Expansion Module 119
Psion Teklogix WORKABOUT PRO HKD User Manual
I
Index
EEPROM contents
Multi-I/O Expansion Module 119
PCMCIA Expansion Module 104
EEPROM write control
enabling jumper on Multi-I/O Expansion Module 114
enabling
FFUART 23
PCMCIA socket 23
serial lines through tether port 46
endcap
removing and installing 33
sealing 36
EV15 Specs 6
expansion module
and GPIO lines 71
EEPROM addresses 74
EEPROM and 74
EEPROM data format 75
installing 34
location of connector 35
overview 63
PCMCIA signals to 72
pinout of connector 64
USB port 71
wakeup input from 73
expansion module connection
data and address buses in 70
power and ground on 69
serial lines on 70
signals on 63
F
features
Multi-I/O Expansion Module 107, 108
PCMCIA Expansion Module 101
FF UART
connector on Multi-I/O Expansion Module 110
FFUART
enabling 23
flex cable 85
G
GPIO lines
for expansion modules 71
GR1 to GR3
jumper on scanner converter board 92
GSM radio 4
H
hardware
overview 11
HDK
contents 4
obtaining 6
high-capacity battery pack (WA3006) 8, 6
I
insertion
scanner cable 85
II
Psion Teklogix WORKABOUT PRO HKD User Manual
installation
Multi-I/O Expansion Module 119
installing
endcap 33
expansion module 34
IP sealing
for backplate 35
I2C bus 73
device identification on 73
J
JP1
connector on scanner converter board 94
JP2
connector on scanner converter board 92
jumper
on Multi-I/O Expansion Module
SJ1 114
SJ10 through SJ17 118
SJ18 and SJ19 117
SJ2 114
SJ3 116
on scanner converter board
GR1 to GR3 92
PR1 to PR2 92
R10 to R21 91
jumpers
for configuration of Multi-I/O Expansion Module 113
for configuration of scanner converter board 91
J1
connector on Multi-I/O Expansion Module 109
J2
connector on Multi-I/O Expansion Module 109
J3
connector on Multi-I/O Expansion Module 109
J4
connector on Multi-I/O Expansion Module 110
J5
connector on Multi-I/O Expansion Module 110
J6
connector on Multi-I/O Expansion Module 112
J7
connector on Multi-I/O Expansion Module 113
K
key
registry, for enabling FFUART 23
registry, for enabling PCMCIA socket 23
keyboard processor 12, 13
kits
scanner kits 33
L
LED 15
LIF connector
block diagram of 52, 53, 55
pinout 50
location
card stop 36
expansion module connector 35
Index
of configuration components
for Multi-I/O Expansion Module 113
100-pin connector 35
M
materials 34
mechanical
models of backplate 35
models
of backplate and scanner device 35
MQ1188 13
MSP430MF133 12, 13
Multi-I/O Expansion Module
and scanner cable 119
configuration 113
connector
serial FF UART 110
serial for scanner 109
USB Host 1 112
USB Host 2 110
connectors 108
control of FFUART level conversion on 117
EEPROM contents of 119
EEPROM in adaptor 119
EEPROM write control configuration on 114
features 107, 108
installation 119
location of configuration components 113
overview 107
power and ground on 118
power during suspend state 119
slot power control configuration on 114
TTL output option for scanner serial on 118
voltage configuration
for high-power output on 116
for standard-power output on 115
multimedia controller 13
N
nCARD_D_DIR signal 103
non-Psion teklogix drivers 21
nPC_BVD1 signal 103
nPC_CD1 signal 103
nPC_CD2 signal 103
nPC_RST signal 103
nPC_VS1 signal 103
nSLOT_BUF_EN signal 103
nSLOT_BUF_OE signal 103
nSLOT_BVD1 signal 103
nSLOT_CD signal 103
nSLOT_PSKTSEL signal 103
nSLOT_PWR_EN signal 103
nSLOT_PWR_SEL signal 103
nSLOT_RST signal 103
nSLOT_VS1 signal 103
nSLOT_5V_EN signal 103
overview
expansion module 63
hardware 11
Multi-I/O Expansion Module 107
PCMCIA Expansion Module 101
scanner converter board 91
WORKABOUT PRO 6
P
PCMCIA
enabling socket 23
PCMCIA compatibility
of PCMCIA Expansion Module 102
PCMCIA driver 21
PCMCIA Expansion Module
accepted card types 102
and PCMCIA compatibility 102
buffer direction signals on 103
buffer enable signals on 103
Card Detect signals on 103
connectors 101
EEPROM contents of 104
overview and features 101
slot power enable signals on 103
unused signals on 104
PCMCIA signals
to expansion modules 72
PCO driver 21
peripheral control driver 21
pinout
expansion-module connector 64
for LIF connector 50
for serial connector 56
for tether connector 44
scanner connector 83
scanner converter board
flex cable connector 92
scan engine connector 94
100-pin connector 64
Port Replicator
serial connector pinout 56
power and ground
on expansion module connection 69
on Multi-I/O Expansion Module 118
on scanner connector 85
on scanner converter board 96
power connector
on Multi-I/O Expansion Module 113
power management 15
PR1 to PR2
jumper on scanner converter board 92
PXA255 11
Q
quad cradle
block diagram of 52
O
obtaining HDK 6
operating systems 7
Psion Teklogix WORKABOUT PRO HKD User Manual
III
Index
R
radio
Bluetooth specs 5
GSM/SPRS/EDGE 4
RA2041 radio specifications 3
RA3030-G2 GSM radio specifications 4
specifications 8, 3
802.11b/g Direct Sequence SS 3
radio specifications 4, 7, 8, 3
RA2041 radio specifications 3
RA3030-G2 GSM radio specifications 4
recommended material and texture 34
registry
enabling FFUART through 23
enabling PCMCIA socket through 23
removing
endcap 33
resistor
on Multi-I/O Expansion Module
R1 and R2 115
R6 and R7 116
zero-ohm (jumper) 91
resistors
for configuration of Multi-I/O Expansion Module 113
R1 and R2
resistor on Multi-I/O Expansion Module 115
R10 to R21
jumper on scanner converter board 91
R6 and R7
resistor on Multi-I/O Expansion Module 116
S
scan engine connector
on converter board 94
scanner
kits 33
scanner cable 85
and Multi-I/O Expansion Module 119
insertion 85
scanner connection
COM port on 87
overview 81
serial ports 87
signals on 86
USB ports 87
scanner connector
on Multi-I/O Expansion Module 109
pinout 83
power and ground on 85
scanner converter board
CN3 connector 96
configuration jumpers for 91
electrical overview 91
JP1 connector 94
JP2 connector 92
power and ground on 96
signals on 96
scanner device 81
models 35
weight 35
IV
Psion Teklogix WORKABOUT PRO HKD User Manual
scanner module (SE 955)
specs 3
scanner serial
connector on Multi-I/O Expansion Module 109
scanning
specifications 3
specifications, imager 7
sealing
backplate 35
endcap 36
serial
connector on Multi-I/O Expansion Module 110
enabling through tether port 46
pinout 56
serial for scanner
connector on Multi-I/O Expansion Module 109
serial lines
in expansion module connection 70
serial port
on scanner connector 87
serial port driver 21
SE 955 scanner specs 3
signals
on expansion module connection 63
on scanner connection 86
on scanner converter board 96
SJ1
jumper on Multi-I/O Expansion Module 114
SJ10 through SJ17
jumper on Multi-I/O Expansion Module 118
SJ18 and SJ19
jumper on Multi-I/O Expansion Module 117
SJ2
jumper on Multi-I/O Expansion Module 114
SJ3
jumper on Multi-I/O Expansion Module 116
slot power control
enabling jumper on Multi-I/O Expansion Module 114
slot power enable signals
and PCMCIA Expansion Module 103
specifications 11
for WORKABOUT PRO 3
SE 955 scanner 3
802.11b 4
802.11g 7
super high-capacity battery pack (WA3010) 8, 9
suspend state
and power in Multi-I/O Expansion Module 119
T
tether
enabling serial through 46
pinout 44
text conventions 4
textures 34
threshold voltage 16
trigger-switch connector 96
TTL output option for scanner serial
enabling jumpers on Multi-I/O Expansion Module
118
Index
U
unused signals
on PCMCIA Expansion Module 104
UP 12
uP 13
USB Host 1
connector on Multi-I/O Expansion Module 112
USB Host 2
connector on Multi-I/O Expansion Module 110
USB port
on scanner connector 87
USB port assignment
for expansion module 71
V
variants
WORKABOUT PRO 6, 11
voltage
battery threshold 16
voltage configuration
for high-power output on Multi-I/O Expansion
Module 116
for standard-power output on Multi-I/O Expansion
Module 115
W
wakeup input
in expansion module connector 73
weight
backplate and scanner device 35
Windows
drivers 21
Windows Mobile 6 drivers 21
Windows versions 7
WM9705 13, 15
WORKABOUT PRO
approvals 4, 6
overview 6
specifications 3
variants 6, 11
Z
zero-ohm resistor (jumper) 91
100-pin connector
location 35
on Multi-I/O Expansion Module 109
power and ground on 69
signals on 63
wakeup input on 73
802.11b/g radio 3
Psion Teklogix WORKABOUT PRO HKD User Manual
V
">