Instruction Manual

DSS-200

R

5.1 Power Amplified Home Theatre Speaker System w/ Remote Control

Read this manual carefully to get the excellent acoustics from this unit.

SPECIFICATIONS

20. L/R Balance (Stereo)........................................................ 1.5dB

Size and Net Weight:

21. Size Of Subwoofer (WxHxD).........................200x335x400(mm)

22. Size Of Front Speaker (DxH)................................F86x1050(mm)

23. Size Of Centre Speaker (DxH).................................F86x350(mm)

24. Size Of Rear Speaker (DxH)..................................F86x1050(mm)

25. Net Weight.......................................................................22.8kg

SAFETY INFORMATION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

!!

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,

WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO

ALERT THE USER TO THE PRESENCE OF UNINSULATED,

" DANGEROUS VOLTAGE ", WITHIN THE PRODUCT'S EN-

CLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO

CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL

!!

PRESENCE OF IMPORTANT OPERATING AND MAIN-

TENANCE (SERVICING) INSTRUCTIONS IN THE LITERA-

TURE ACCOMPANYING THE APPLIANCE.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

20 1

IMPORTANT SAFEGUARDS

1. Read Instructions - All the safety and operating instructions should

be read before the appliance is operated.

2. Retain Instructions - The safety and operating instructions should

be retained for future reference.

3. Follow Instructions - All operating instructions should be followed.

4. Heed Warnings - All warnings on the appliance and in the opera-

ting instructions should be adhered to.

5. Power Source - The appliance should be connected to a power

supply only of the type specified in the operating instructions or

as marked on the appliance.

6. Power-cord Protection - Power-supply cords should be routed so

that they are not likely to be walked on or pinched by items placed

upon or against them, pay particular attention to cords at plugs,

convenience receptacles, and the point where they exit from the

appliance.

7. Water and Moisture - The appliance should not be used near water

(for example, near a bathtub, washbowl, kitchen sink, laundry tub,

in a wet basement, or near a swimming pool, etc.)

8. Ventilation - The appliance should be situated so that its location

or position does not interfere with its proper ventilation. Do not

use the appliance on a bed, sofa, rug or similar surface that may

block the ventilation openings.

2

SPECIFICATIONS

1. Power Supply.........................................................AC 230V/50Hz

2. Power Consumption............................................................200W

3. Input Sensitivity (Subwoofer)...................................60mV 20mV

4. Input Sensitivity (Satellite)......................................300mV 50mV

5. Speaker Impedance (Subwoofer)........................................8 Ohm

6. Speaker Impedance (Satellite).............................................4 Ohm

7. S/N (A Weight)....................................................................³72dB

8. Subwoofer Power Output (RMS)..........................................50W

9. Front Speaker Power Output (RMS)..................................15Wx2

10. Centre Speaker Power Output (RMS)..................................15W

11. Rear Speaker Power Output (RMS).................................15Wx2

12. THD (1kHz, 1W)................................................................£0.5%

13. Bass (100Hz).................................................................... 8dB

14. Treble (10kHz).................................................................. 8dB

15. Frequency Response (Subwoofer)..............40Hz~200Hz 5dB

16. Frequency Response (Front Speaker)........200Hz~20kHz 5dB

17. Frequency Response (Centre Speaker)......200Hz~20kHz 5dB

18. Frequency Response (Rear Speaker).........200Hz~20kHz 5dB

19

TROUBLE SHOOTING

5. REAR SPEAKER SILENT

(1) Check whether the system is connected correctly with the

Rear speaker.

(2) Check whether the system is connected correctly with the audio

source.

(3) Check whether 2.1CH is selected as audio output.

(4) Check whether 3.1CH is selected as audio output.

SUPPLEMENT

To improve the effect of the system, please note the following when you connect the DVD player as the audio input.

1. When 5.1 channel audio input is selected, the DVD player should

be set as multi-channel and choose the proper Disc format.

2. This speaker system is 5.1 channel satellite speaker system, so in

the speaker setting (in DVD menu) for the DVD player, the front,

If the detailed instruction about DVD player setting is required, please

read the instruction manual carefully.

18

IMPORTANT SAFEGUARDS

9. Heat - Keep the appliance away from heat sources such as radiators,

heat registers, stoves, or other appliances (including amplifiers)

that produce heat.

10. Nonuse Periods - The power cord of the appliance should be un-

plugged from the outlet when left unused for a long period of

time.

11. Damage requiring service - The appliance should be serviced by

qualified service personnel when:

a/ The power-supply cord or the plug has been damaged; or

b/ Objects have fallen or liquid has been spilled into the appliance;

or

c/ The appliance has been exposed to rain; or

d/ The appliance does not appear to operate normally or exhibits

a marked change in performance; or

e/ The appliance has been dropped, or the enclosure damaged.

12. Servicing - The user should not attempt to service the appliance

beyond that specified in the operating instructions. All other ser-

vicing should be referred to qualified service personnel.

13. Clean only with dry cloth.

14. Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult and electrician for replacement of the obsolete outlet.

15. Unplug this apparatus during lightning storms or when unused

for long periods of time.

3

FRONT PANEL - CONTROLS AND FUNCTIONS

1

2

3

4

5

R

2CH

5.1CH

SURR. A

STANDBY MUTE

INPUT SURROUND VOL- VOL+

SURR. B

AC-3

5.1 R E A D Y

REMOTE SENSOR

5.1 R E A D Y

11

10

9

8

7

6

1. 2CH: 2 Channel Input Indicator.

2. 5.1CH: 5.1 Channel Input Indicator.

3. INPUT Button.

4. SURROUND: Surround Sound Decoder.

5. REMOTE SENSOR: Remote Receiver.

6. STANDBY: Power Standby.

7. VOL-: Volume Down.

8. VOL+: Volume Up.

9. MUTE: Power Standby and Mute Indicator .

10. SURR. A: 3D Stereo Indicator.

11. SURR. B: 5.1 Stereo Indicator.

4

TROUBLE SHOOTING

1. NO OUTPUT

(1) Check whether the system is connected correctly.

(2 ) Check whether the Volume is set at minimum. Adjust it accordingly.

(3) Check whether the Audio Input is in PLAY mode.

2. FRONT LEFT SPEAKER SILENT

(1) Check whether the system is connected correctly with the Front

Left speaker.

(2) Check whether the Balance function is switched off. Adjust it

accordingly.

(3) Check whether the system is connected correctly with the audio

source.

3. FRONT RIGHT SPEAKER SILENT

(1) Check whether the system is connected correctly with the Front

Right speaker.

(2) Check whether the Balance function is switched off. Adjust it

accordingly.

(3) Check whether the system is connected correctly with the audio

source.

4. CENTRE SPEAKER SILENT

(1) Check whether the system is connected correctly with the Centre

speaker.

(2) Check whether the system is connected correctly with the audio

source.

(3) Check whether 2.1CH is selected as audio output.

17

OPERATING INSTRUCTION - MAIN UNIT

the Rear Right Speaker output and STANDBY indicator (9) will

light up and flash.

2. Press RR - button (37) on the remote controller to minimize the

Rear Right Speaker output and STANDBY indicator (9) will light

up and flash.

J. 5.1 CHANNELS INPUT Selection

1. Connect the system properly. 5.1 Channels audio output must

decode 5.1 Channels output.)

2. Press INPUT button (25) on the remote controller to shift the

status for audio input to 5.1CH channels input.

3. Adjust all output settings including VOLUME, BASS, TREBLE

(if necessary) now to enjoy the wonderful and tremendous Home

Theatre effects.

K. MUTE Selection

1. Press the MUTE button (33) on the remote controller once to

keep the performance silent.

2. MUTE indicator (9) on the front panel will then light up and flash.

3. Press it again to resume the performance.

L. PRESET Selection

Press on PRESET button (34) on the remote controller will reset

all settings including BALANCE, CENTRE Speaker output, REAR

Speaker output to 0dB status preset by the manufacturer.

16

REAR PANEL - CONTROLS AND FUNCTIONS

12

13

14

15

16

17

18

2CH

L W

5.1CH INPUT

RL FL

R C RR FR

SPEAKER OUTPUT

FR FL C RL RR

R

5.1 Power Amplified Home Theatre

Speaker System w/ Remote Control

MODEL NO.

:DSS-200

POWER SOURCE :AC~230V/50Hz

POWER CONSUMPTION:200W www.denver-electronics.com

ON

OFF

POWER

AC~230V/50Hz

SERIAL NO:

12. 5.1CH Subwoofer Audio Input.

13. Stereo Left Audio Input.

14. Stereo Right Audio Input.

15. 5.1CH Centre Audio Input.

16. Speaker Output.

FR: Front Right Speaker Output.

FL: Front Left Speaker Output.

C: Centre Speaker Output.

RL: Rear Left Speaker Output.

RR: Rear Right Speaker Output.

5

19

20

21

22

REAR PANEL - CONTROLS AND FUNCTIONS

17. AC Power Cord.

18. Power On/Off Switch.

19. 5.1CH Rear Left Audio Input.

20. 5.1CH Front Left Audio Input.

21. 5.1CH Front Right Audio Input.

22. 5.1CH Rear Right Audio Input.

SETTING UP THE ALUMINIUM DIE-CASTING SPEAKERS

Remove the base, aluminium speakers, screws, and rubber feet from the packaging. Now you can set it up as follows:

1. Place the base at the bottom of the speaker pole, insert and

tighten the screws to secure the base to the speaker.

2. Stick the rubber foot on the base.

6

OPERATING INSTRUCTION - MAIN UNIT

3.1CH Stereo

5.1CH

5.1CH (Strengthened)

On

Off

On

Off

On

On

G. CENTRE SPEAKER Selection

1. Press C + button (28) on the remote controller to maximize the

Centre Speaker output and STANDBY indicator (9) will light up

and flash.

2. Press C - button (38) on the remote controller to minimize the

Centre Speaker output and STANDBY indicator (9) will light up

and flash.

H. REAR LEFT SPEAKER Selection

1. Press RL + button (27) on the remote controller to maximize

the Rear Left Speaker output and STANDBY indicator (9) will

light up and flash.

2. Press RL - button (29) on the remote controller to minimize the

Rear Left Speaker output and STANDBY indicator (9) will light

up and flash.

I. REAR RIGHT SPEAKER Selection

1. Press RR + button (36) on the remote controller to maximize

15

OPERATING INSTRUCTION - MAIN UNIT

2. Press the BASS - button (32) on the remote controller to mini-

mize the Bass output. Standby Indicator (9) on the front panel

will light up and flash when the Bass Output is decreased to

Minimum accordingly.

D. TREBLE Selection

1. Press the TREBLE + button (39) on the remote controller to

maximize the Treble output. Standby Indicator (9) on the front

panel will light up and flash when the Treble Output is increased

to Maximum accordingly.

2. Press the TREBLE - button (40) on the remote controller to mini-

mize the Treble output. Standby Indicator (9) on the front panel

will light up and flash when the Treble Output is decreased to

Minimum accordingly.

E. BALANCE Selection

1. Press the BALANCE L button (26) on the remote controller to

minimize the Left speaker output.

2. Press the BALANCE R button (35) on the remote controller to

minimize the Right speaker output.

3. Standby Indicator (9) on the front panel will light up and flash

when the Balance Output is adjusted almost to the Centre status.

F. SURROUND DECODER Selection

1. Connect and place Centre and Rear speakers properly.

2. Press on SURROUND button (4) on the front panel of the main

unit or (24) on the remote controller to select Surround Decoder

for Home Theatre system effects.

14

SYSTEM CONNECTION INSTRUCTION

2CH

L W

5.1CH INPUT

RL FL

R C RR FR

SPEAKER OUTPUT

FR FL C RL RR

R

5.1 Power Amplified Home Theatre

Speaker System w/ Remote Control

MODEL NO.

:DSS-200

POWER SOURCE :AC~230V/50Hz

POWER CONSUMPTION:200W www.denver-electronics.com

ON

OFF

POWER

AC~230V/50Hz

SERIAL NO:

(Optional)

To Stereo Output

TV

Woofer Rear-L Front-L

Center Rear-R Front-R

Audio Out

Woofer Rear-L Front-L

Optical Coaxial Center Rear-R Front-R

Video Out

Video S-Video U Y V

Video Out

Scart out

Manufactured under license from Dolby Laboratories.

"Doldy","Dolby Digital", and the double-D symbol are trademarks of Dolby Laboratories. Confidential

Unpublished Works.

@1992-1997 Dolby Laboratories, Inc.

All rights reserved.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

!!

Apparatus Claims of U.S. Patent Nos.

4,631,603;4,577,216;4,819,098 and 4,907,093

licensed for limited viewing uses only.

AC 100V~240V

50/60Hz

DVD Player

Video In

7

SYSTEM CONNECTION INSTRUCTION

Use the SPEAKER OUTPUT jacks on the rear panel of main unit to connect to the satellite speakers.

SPEAKER OUTPUT

FR FL C RL RR

Front Right Speaker

8

OPERATING INSTRUCTION - MAIN UNIT

A. Switch On/Off the Product

1. Before turning on the system, please connect it according to

the System Connection Instruction.

2. Connect AC power supply with this product.

3. Press on the power switch button (18) on the Rear Panel of the main

unit to switch on the system, the standby indicator will light up.

Press it once again to switch off the unit. Then press the standby

button (6) on the main unit or button (23) on the remote controller

to enter the normal status. Press the button (6) or button (23) on

the remote controller once again to keep power in standby status.

B. VOLUME Selection

1. Press the VOL+ button (8) on the front panel of the main unit

or VOLUME + button (31) on the remote controller to maximize

the sound output. Standby Indicator (9) on the front panel will

light up and flash when the Volume is increased to Maximum

accordingly.

2. Press the VOL- button (7) on the front panel of the main unit

or VOLUME - button (41) on the remote controller to minimize

the sound output. Standby Indicator (9) on the front panel will

light up and flash when the Volume is decreased to Minimum

accordingly.

C. BASS Selection

1. Press the BASS + button (30) on the remote controller to maxi-

mize the Bass output. Standby Indicator (9) on the front panel

will light up and flash when the Bass Output is increased to

Maximum accordingly.

13

OPERATING INSTRUCTION - REMOTE CONTROLLER

5. To properly use the remote controller, please put its front emitter

right at the receiving lattice (remote sensor) of the main system.

6. The normal and effective distance for operating the system by the

remote controller is 7 meters within the system, and at 30 angle

left or right diverged away from the system.

OPERATING INSTRUCTION - CONTROLS AND FUNCTIONS

23

24

25

26

27

28

29

30

31

32

POWER MUTE

SURROUND INPUT PRESET

L BALANCE R

RL C

__

RR

__

BASS

__

VOLUME

__

TREBLE

__

DSS-200

R

33

34

35

36

37

38

39

40

41

12

23. POWER: Power Standby.

24. SURROUND: Surround Decoder.

25. INPUT: Input Switch.

26. BALANCE L: Left Speaker Balance.

27. RL +: Rear Left Balance Output Up.

28. C +: Centre Output Up.

29. RL -: Rear Left Balance Output Down.

9

OPERATING INSTRUCTION - CONTROLS AND FUNCTIONS

30. BASS +: Bass Output Up.

31. VOLUME +: Main Volume Up.

32. BASS -: Bass Output Down.

33. MUTE: Output Suspension.

34. PRESET: Location retrieval.

35. BALANCE R: Right Speaker Balance.

36. RR +: Rear Right Balance Output Up.

37. RR -: Rear Right Balance Output Down.

38. C -: Centre Output Down.

39. TREBLE +: Treble Output Up.

40. TREBLE -: Treble Output Down.

41. VOLUME -: Main Volume Down.

OPERATING INSTRUCTION - REMOTE CONTROLLER

1. Before using the remote controller, please insert correct type of

batteries into the battery compartment.

2. The remote controller uses 2x1.5V/AAA batteries.

3. Please insert the batteries as indicated below.

a/ Remove the battery compartment cover.

b/ Insert 2 batteries as per the polarities marked inside the battery

compartment.

c/ Replace the battery cover.

10

4. If the remote controller is of no function, please check the batteries

or change new batteries before consulting technical personnel.

11