Regency Horizon

™

HZO42 Outdoor

Gas Fireplace

Owners &

Installation Manual

MODELS: HZO42-NG

HZO42-LP

WARNING: FOR OUTDOOR USE ONLY www.regency-fi re.com

WARNING: FOR YOUR SAFETY

If the information in these instructions are not followed exactly, What to do if you smell gas: a fi re or explosion may result causing property damage, Do not try to light any appliance personal injury or loss of life. Do not touch any electrical switch: do not use any phone in your

FOR YOUR SAFETY

Do not store or use gasoline or other fl ammable vapours and liquids in the vicinity of this or any other appliance.

building.

Immediately call your gas supplier from a neighbour's phone. Follow

Installation and service must be performed by a qualifi ed installer, service agency or the gas supplier.

the gas supplier's instructions.

If you cannot reach your gas supplier, call the fi re department.

WARNING:

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.

Tested by:

Installer: Please complete the details on the back cover and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

918-882e FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4 02/20/13

To the New Owner:

Congratulations!

You are the owner of a state-of-the-art Gas Fireplace by REGENCY

®

. The Horizon™ HZO42

Outdoor fi replace has been designed to provide you with all the warmth and charm of a fi re at the fl ick of a switch. The Horizon™ HZO42 Outdoor fi replace has been approved by Warnock Hersey/

Intertek for both safety and effi ciency. As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a moment now to acquaint yourself with these instructions and the many features of your Regency

®

Fireplace.

2

Regency Horizon™ HZO42 Gas Fireplace

SAFETY LABEL

Copy of Safety Decal .....................................................4

DIMENSIONS

Unit Dimensions ............................................................5

INSTALLATION

Important Message ......................................................6

Before You Start ............................................................6

General Safety Information............................................6

Installation Checklist ......................................................7

Locating Your Gas Fireplace .........................................7

Important Installation Info for outdoor appliances..........8

Minimum Clearances to combustibles ...........................9

Framing Dimensions....................................................10

Mantel Clearances....................................................... 11

Non-Combustible Requirements ................................. 11

Finishing ......................................................................12

High Elevation .............................................................13

Gas Line Installation ....................................................13

Pilot Adjustment ...........................................................13

Gas Pipe Pressure Testing ..........................................13

880 S.I.T. Valve Description .........................................13

Aeration Adjustment ....................................................13

Unit Assembly Prior to Installation ...............................14

Standoff Assembly ...............................................14

Nailing Strips ........................................................14

Drain Installation (Recommended) ..............................15

Wall switch and battery installation ..............................16

Wiring Diagram ............................................................17

Inner panel installation.................................................18

Glass crystal installation .............................................19

Pebble installation .......................................................20

Volcanic stone installation ..........................................21

Optional Log Set Installation........................................22

Heat defl ector installation ............................................24

Faceplate installation ...................................................25

Glass wind shield installation.......................................26

Weather cover installation / removal ...........................26

TABLE OF CONTENTS

Operating Instructions .................................................32

Lighting Procedure ......................................................32

Shutdown Procedure ...................................................32

First Fire ......................................................................32

Aeration Adjustment ....................................................32

Copy of Lighting Plate Instructions ..............................33

Maintenance Instructions.............................................34

Valve assembly Replacement .....................................35

Battery Replacement ...................................................36

Main Assembly ............................................................38

Burner Assembly .........................................................39

Accessories .................................................................40

WARRANTY

Limited Warranty: ......................................................43

3

Regency Horizon™ HZO42 Gas Fireplace

SAFETY LABEL

This is a copy of the label that accompanies each

HZO42 Outdoor Fireplace. We have printed a copy of the contents here for your review.

NOTE: Regency ® units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.

For the State of Massachusetts, installation and repair must be done by a plumber or gas fi tter licensed in the Commonwealth of Massachusetts.

For the State of Massachusetts, fl exible connectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.

4

Regency Horizon™ HZO42 Gas Fireplace

Regency Horizon™ HZO42 Gas Fireplace

UNIT DIMENSIONS

DIMENSIONS

37 - 13/16” (960mm)

41 - 11/16” (1059mm)

43 - 11/16” (1110mm)

39 - ½” (1003mm)

35 - 1/4” (895mm)

5/8” (16mm)

16 - 1/8” (410mm)

15 - 9/16” (395mm)

13 - 3/4” (349mm)

5

INSTALLATION

IMPORTANT MESSAGE

SAVE THESE

INSTRUCTIONS

The HZO42 Gas Fireplace must be installed in accordance with these instructions. Carefully read all the instructions in this manual fi rst. Consult the

"authority having jurisdiction" to determine the need for a permit prior to starting the installation. It is the responsibility of the installer to ensure this fi replace is installed in compliance with manufacturers instructions and all applicable codes.

BEFORE YOU START

DO NOT USE THIS APPLIANCE IF

ANY PART HAS BEEN UNDER WATER.

IMMEDIATELY CALL A QUALIFIED

SERVICE TECHNICIAN TO INSPECT

THE APPLIANCE AND TO REPLACE

ANY PART OF THE CONTROL SYSTEM

AND ANY GAS CONTROL WHICH HAS

BEEN UNDER WATER.

CLOTHING OR OTHER FLAMMABLE

MATERIAL SHOULD NOT BE PLACED

ON OR NEAR THE APPLIANCE.

5) To prevent injury, do not allow anyone who is unfamiliar with the operation to use the fi replace.

6) Wear gloves and safety glasses for protection while doing required maintenance.

7) Maximum gas inlet pressure = 1/2 psig.

8) Under no circumstances should this appliance be modifi ed. Parts that have to be removed for servicing should be replaced prior to operating this appliance.

9) Installation and any repairs to this appliance should be done by a qualifi ed service person.

A professional service person should be called to inspect this appliance annually. Make it a practice to have all of your gas appliances checked annually.

Safe installation and operation of this appliance requires common sense, however, we are required by the Canadian Safety Standards and ANSI

Standards to make you aware of the following:

INSTALLATION AND REPAIR SHOULD

B E D O N E B Y A N AU T H O R I Z E D

SERVICE PERSON. THE APPLIANCE

SHOULD BE INSPECTED BEFORE

USE AND AT LEAST ANNUALLY BY A

PROFESSIONAL SERVICE PERSON.

MORE FREQUENT CLEANING MAY

BE REQUIRED DUE TO EXCESSIVE

LINT FROM CARPETING, BEDDING

MATERIAL, ETC. IT IS IMPERATIVE THAT

CONTROL COMPARTMENTS, BURNERS

AND CIRCULATING AIR PASSAGEWAYS

OF THE APPLIANCE BE KEPT CLEAN.

ANY GUARD OR OTHER PROTECTIVE

DEVICE REMOVED FOR SERVICING

THE APPLIANCE MUST BE REPLACED

PRIOR TO OPERATING THE APPLIANCE

WARNING: FAILURE TO INSTALL THIS

APPLIANCE CORRECTLY WILL VOID

YOUR WARRANTY AND MAY CAUSE A

SERIOUS FIRE.

CHILDREN AND ADULTS SHOULD

BE ALERTED TO THE HAZARDS OF

HIGH SURFACE TEMPERATURES,

ESPECIALLY THE FIREPLACE GLASS

AND FACEPLATE, AND SHOULD STAY

AWAY TO AVOID BURNS OR CLOTHING

IGNITION.

YOUNG CHILDREN SHOULD BE CARE-

FULLY SUPERVISED WHEN THEY ARE

IN THE SAME AREA AS THE APPLI-

ANCE. TODDLERS, YOUNG CHILDREN

AND OTHERS MAY BE SUSCEPTIBLE

TO ACCIDENTAL CONTACT BURNS. A

PHYSICAL BARRIERS IS RECOMMEND-

ED IF THERE ARE AT RISK INDIVIDUAL

IN THE HOUSE. TO RESTRICT ACCESS

TO A FIREPLACE OR STOVE, INSTALL

AN ADJUSTABLE SAFETY GATE TO

KEEP TODDLERS, YOUNG CHILDREN

AND OTHER AT RISK INDIVIDUALS OUT

OF THE ROOM AND AWAY FROM HOT

SURFACES.

10) Under no circumstances should any solid fuels

(wood, paper, cardboard, coal, etc.) be used in this appliance.

11) The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5kPa).

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.5 kPa).

12) The appliance area must be kept clear and free of combustible materials, (gases and other fl ammable vapours and liquids).

It is highly recommended to protect the interior from moisture (rain, snow). Cover the enclosure opening when not in use. This fi replace is only for use with the type of gas indicated on the rating plate. This fi replace is not convertible for use with other gases, unless a certifi ed kit is used.

GENERAL SAFETY

INFORMATION

13) Cover must be removed when burner is in

operation.

1) The installation must conform with local codes or, in the absence of local codes, with

CAN/CSA-B149.1, Natural Gas and Propane

Installation Code or CAN/CSA-B149.2, Propane installation code the Natural Gas Fuel Code,

ANSI Z223.1/NFPA 54.

14) When not using appliance for extended periods of time - turn off gas supply.

Emissions from burning wood or gas could contain chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm.

2) The appliance when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes with the

Canadian Electrical Code CSA C22.1or with the National Electrical Code, ANSI/NFPA 70.

THIS APPLIANCE SHALL BE USED

ONLY OUTDOORS IN A WELL-VENTI-

LATED SPACE AND SHALL NOT BE

USED IN A BUILDING, GARAGE OR ANY

OTHER ENCLOSED AREA.

3) See general construction and assembly instructions. The appliance should be enclosed.

4) Inspect the burner before each use of the appliance for blockage and any signs of deterioration.

6

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

INSTALLATION

CHECKLIST

1) Locate appliance:

LOCATING YOUR

GAS FIREPLACE

1) When selecting a location for your fi replace, ensure that the clearances are met.

a) Refer to "Locating Your Gas fi replace" section b) Clearances to Combustibles (Refer to

"Clearances" section) c) Mantel Clearances (Refer to "Combustible

Mantel Clearances" section) d) Framing & Finishing Requirements (Refer to "Framing & Finishing" section)

2) Top Facing Support and Side Nailing Strips

(Refer to "Unit Assembly Prior to Installation"

Section). Note: Must be done before installing unit into place.

2) This appliance must be installed in an open-air situation with natural ventilation, without stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind and natural convection.

3) Certain materials or items, when placed under or near the appliance, will be subjected to radiant heat and could become damaged.

4) Typically an outdoor space is not enclosed but, any enclosure in which the appliance is used shall comply with one of the following:

An enclosure with walls on all sides, but at least one permanent opening at ground level and no overhead cover.

4) Install ON/OFF switch - ensure it is in the OFF position.

5) Make gas connections - test for leaks.

6) Install 4 "AA" batteries

7) Install standard and optional features. Refer to the following sections: a. Inner Panel

Within a partial enclosure that includes an overhead cover and no more that two walls.

c. Pebble Installation (optional) d. Garden Stone Installation (optional) e. Log Installation (optional) f. Glass Wind Shield Installation g. Heat Defl ector Installation i. Weather Cover Installation

This includes:

1) Clocking the appliance to ensure the correct fi ring rate (rate noted on label), after burning appliance for 15 minutes.

2) If required, adjusting the primary air to ensure that the fl ame does not carbon. First allow the unit to burn for 15-20 min. to stabilize.

Within a partial enclosure that includes an overhead cover and more than two walls, the following shall apply:

• At least 25% of the total wall area is completely open, and

• At least 30% of the remaining wall area is open and unrestricted

30% or more in total of the remaining wall area is open and unrestricted.

CAUTION: Any alteration to the product that causes sooting or carboning that results in damage is not the responsibility of the manufacturer.

NOTE: In order to function correctly, these types of appliances require at least 50% open access for permanent ventilation/airfl ow.

Open ventilation/airfl ow space comes from walls and roof/ceiling.

Open fl oor space around the unit must not be considered ventilation/airfl ow space. Open side at least 25% of total wall area

*SEE IMPORTANT INSTALLATION NOTES NEXT PAGE

7

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

IMPORTANT INFORMATION FOR OUTDOOR FIREPLACE INSTALLATIONS

• Never insulate around the body of the unit

• Excessive heat retention in the fi rebox will lead to component failure and fi replace malfunction

• Excessive heat retention will also increase the risk of fi re inside the chase

• Heat retention can cause “Oil-canning” and damage the fi replace due to overheating

• Do not build up a wall of any type in front or to the sides of the appliance, higher than the fi rebox opening. This will create a pressure zone at the fi rebox and will prevent the unit from venting

• This is an outdoor appliance with a built-in drain. This drain should be installed and connected in all applications as per the instructions in this manual

• Inadequate drainage will cause rust and reduce the life of your appliance, this is not protected by warranty

IMPORTANT THINGS TO REMEMBER

• Correct Working Gas pressure is critical on “E” units

• Wherever possible avoid locating on a fl at wall in a tight corner

• Floor space doesn’t count as “open area”

• Install to the manual specs for framing and do not insulate unit or enclosure

• Framing enclosure must at least meet minimum dimensional specs as per the installation manual

• Only Regency approved media should be used in the fi rebox (i.e. stones/glass)

• Be aware of pressure zones due to location (i.e. facing the ocean)

• Open walls and doorways to outside air are benefi cial to the performance of an outdoor appliance

• Fixed roof/ceiling open areas count towards the total open area overall requirement

• Screens create 40% or more air restriction

• Screened areas are restrictions and reduce open air space, calculate area based on a closed screen

• The biggest problems are created by lack of airfl ow for the appliance

• Outdoor fi replaces are often built-in systems and incorrect installation can result in high repair costs

• Units must not be modifi ed or altered in any way

COMPONENTS IN OUTDOOR APPLIANCES

• Outdoor uniits use the same consistent, reliable Electronic components used in most Regency “E” units

• Installed correctly, these components will be subjected to far lower temperatures than indoor units, which have been certifi ed as safe from heat etc

• Working gas pressures are as critical in outdoor products as they are in indoor products, even more important in Electronic systems

ANTICIPATED ISSUES CAUSED BY

INCORRECT LOCATION OR INSTALLATION

COMMON MISCONCEPTIONS REGARDING

OUTDOOR FIREPLACES

• Unit shutting down intermittently

• Overheating of components leading to failure

• There is a common misconception that being outdoors, an Outdoor

Fireplace will function, regardless of circumstances,

• Outdoor fi replaces require the same amount of ventilation as indoor units, often more

• Outdoor unitis require adequate ventilation to the atmosphere, which in turn provides ongoing circulatory combustion air

• This type of Appliance Vents.

• All Outdoor Fireplace Products have the same need for Air/Oxygen, and an ability to Vent

• Even though the appliance is outdoors, this doesn’t mean it is getting adequate air

• Requirements are not specifi c to Regency units

• Read and follow critical location guidelines in this manual

UNDERSTANDING OUTDOOR APPLIANCE

REQUIREMENTS

• Poor fl ame package (i.e. all to one side, lazy fl ame)

• Failure to ignite

• Safety issues and concerns created from the byproducts of combustion

OUTDOOR APPLIANCES REQUIRE VENTING

• Outdoor appliances must be installed in: open-air situations with natural ventilation and without stagnant areas

• Any gas leakage and products of combustion need to be rapidly dispersed by wind and natural convection

• Typically outdoor spaces are not enclosed, however, failure to adhere to installation guidelines, may cause the outdoor fi replace to be affected by wind or air pressure inside the enclosure

• ANY enclosure in which the appliance is used shall comply with one of the diagrams on the previous page.

• Don’t overlook the obvious

• Widen your margin for error

• Combustion always requires the same three elements

• Only the quantities and volumes change

OUTDOOR APPLIANCE INSTALLATION SUMMARY

• All walls + overhead cover = 100% total area

• One of four walls or full overhead area must be totally open, plus—one of remaining walls must have a fi xed opening

• All outdoor fi replaces/fi re tables require total natural ventilation of 50% open space

8

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

MINIMUM CLEARANCES TO COMBUSTIBLES

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of fi res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this fi replace be installed only in accordance with these instructions.

Caution Requirements

The top, back and sides of the fi replace are defi ned by standoffs. The metal ends of the standoff may NOT be recessed into combustible construction.

WARNING

Fire hazard is an extreme risk if these clearances (air space) to combustible materials are not adhered to. It is of greatest importance that this fi replace be installed only in accordance with these instructions.

Clearance:

A: Sidewall

B: Ceiling

C: Mantel Height (min.)

D: Mantel Depth (max.)

E: Alcove Width

F: Alcove Depth

Notes:

Dimension

11" (203mm)

36" (914mm)

18" (457mm)

12" (304mm)

57"(1148mm)

36" (914mm)

0"

HZO42 Clearance Requirements

Measured From:

Side of Fireplace Opening

Top of Fireplace Opening

Top of Fireplace Opening

From Wall

Wall to Wall (Minimum)

Front to Back Wall (Maximum)

No Hearth Required

WARNING:

When installing this appliance; do not cover or surround with insulation.

This appliance can overheat and cause malfunction and component failure, if covered, or partially covered.

If the appliance is installed inside a chase, insulation must be installed on the walls of the chase, not on the appliance.

B

B

D

C

A

F

A

E

F

E

Alcove

9

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

FRAMING DIMENSIONS

Framing

Dimensions

I

J

E

F

G

H

A

B

C

D

Description

Header Height

Side Stud Width

Minimum framing depth

Minimum Height to Combustibles

Minimum framing width

Corner Wall Depth

Corner Facing Wall Width

Gas Connection Opening Height

Gas Connection Height

Gas Connection Inset

HZO42

32-11/16” (30mm)

42 - 3/16" (1072mm)

20" (508mm)

52 - 1/2" (1334mm)

60" (1524mm)

40 - 7/16" (1027mm)

54 - 3/16" (1376mm)

2" (51mm)

3-7/8 " (98mm)

3/4" (73mm)

K Gas Connection Opening Width 3-7/8 " (98mm)

*

Framing depth measurement is noted with the nailing strips set as far forward on the fi rebox as possible.

The nailing strips can be adjusted back up to 1” to allow for varying thicknesses in non-combustible

material & wall fi nishes.

Note: All other framing may be of wood construction.

Metal Stud on edge

A

B

C

D

K

E

F

J

I H

J

G

10

Important Note: Two (2) ventilation grills are highly recommended for all enclosures.

This is to alleviate moisture and allow for air to circulate. Minimum recommended size: 20" sq (508 mm²) ea.

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

MANTEL CLEARANCES

14 12 10 8 6 4 2

0

Due to the extreme heat this fi replace emits, the mantel

clearances are critical. Combustible mantel clearances from top of front facing are shown in the diagram on the right.

26

12" (305mm) facing is "heat resistant" or the paint may discolour.

Combustible Material

20

10

26-1/2”

1" (25mm)

18”

Metal Stud

(On Edge)

Non-combustible

Facing

11”

Standoff

0

To Unit

Base

23”

Top of

Fireplace

Opening

NON-COMBUSTIBLE REQUIREMENTS

43-11/16” (1110mm)

Non-combustible

Material

38-1/16” (767mm)

Non-combustible Material

2-7/8”

Regency Horizon™ HZO42 Gas Fireplace

6-9/16”

(167mm)

11

INSTALLATION

FINISHING

IMPORTANT FINISHING DETAIL NOTE:

Before placing unit into fi nal position - it is important to know the total thickness / height of fi nished hearth. The base of the fi replace should be level or higher than the fi nished hearth height.

If material such as brick, stone, etc extends past the faceplate depth (1-1/2"), when fi nishing around the faceplate, the minimum opening dimensions noted below must be adhered to ensuring for the removal of the faceplate and for the safe operation of this appliance.

For material such as brick, stone, etc that extend up to 1-1/2" , the minimum opening dimensions noted below must be adhered, when fi nishing around the faceplate. This is to ensure the removal of the faceplate and for the safe operation of this appliance.

12

Unit shown without faceplate

For facing material is over 1” (25mm)thick, use the outer cut out for your faceplate template.

40 1/4”

HZO42

For facing material is under 1” (25mm) thick, use the inner cut out to keep construction material out of the fi rebox.

38”

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

HZO42 SYSTEM DATA

Max. Supply Pressure 14" WC (3.49 kpa)

Min. Supply Pressure 5" WC (1.25 kpa)

Manifold Pressure

Orifi ce Size

Maximum Input

3.5" WC (0.87 kpa)

#29 DMS

44,500 Btu/h

(13.04 kW)

PILOT ADJUSTMENT

880 S.I.T. VALVE

DESCRIPTION

Periodically check the pilot fl ames. Correct fl ame pattern has two strong blue fl ames: 1 fl owing around the fl ame sensor and 1 fl owing across the burner (it does not have to be touching the burner).

Burner

4) Pilot Outlet

5) Main Gas Outlet

6) Main Gas Inlet

Flame Sensor

HZO42-LP SYSTEM DATA

Max. Supply Pressure 14" WC (3.49 kpa)

Min. Supply Pressure 11" WC (2.73 kpa)

Manifold Pressure

Orifi ce Size

Maximum Input

10" WC (2.49 kpa)

#47 DMS

43,500 Btu/h

(12.74 kW)

Pilot Ignitor

3

2

Note: If you have an incorrect fl ame pattern, contact your Regency ® dealer for further instructions.

HIGH ELEVATION

Incorrect fl ame pattern will have small, probably yellow fl ames, not coming into proper contact

with the rear burner or fl ame sensor.

This unit is approved for altitude 0 to 4500 ft. (CAN1

2.17-M91).

GAS PIPE PRESSURE

TESTING

GAS LINE

INSTALLATION

Since some municipalities have additional local codes it is always best to consult with your local authorities and the CAN/CGA B149 installation code.

For USA installations follow local codes and/or the current National Fuel Gas Code, ANSI Z223.1.

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at pressures over 1/2 psig.

The manifold pressure is controlled by a regulator built into the gas control, and should be checked at the pressure test point.

When using copper or fl ex connectors use only approved fi ttings. Always provide a union so that gas lines can be easily disconnected for servicing.

Flare nuts for copper lines and fl ex connectors are usually considered to meet this requirement.

Note: To properly check gas pressure, both inlet and manifold pressures should be checked using the valve pressure ports on the valve.

1) Make sure the valve is in the "OFF" position.

NOTE: A shutoff / dante valve should be supplied in or near the unit (or as per local codes) for ease of servicing this appliance.

2) Loosen the "IN" and/or "OUT" pressure tap(s), turning counterclockwise with a

4

5

1

6

AERATION ADJUSTMENT

The burner aeration is factory set but may need adjusting due to either the local gas supply or altitude. Open the air shutter for a blue fl ame or close for a more yellow fl ame.

IMPORTANT: Always check for gas leaks with a soap and water solution or gas leak detector.

Do not use open fl ame for leak testing.

3) Attach manometer to "IN" and/or "OUT" pressure tap(s) using a 5/16" ID hose.

4) Light the pilot and turn the valve to "ON" position.

Minimum Air Shutter Opening:

1/8" NG

1/4" LP

5) The pressure check should be carried out with the unit burning and the setting should be within the limits specifi ed on the safety label.

Note: Any damage due to carboning resulting from improperly setting the aeration controls is NOT covered under warranty.

gas valve, disconnect the hose and tighten the screw (clockwise) with a 1/8" fl at screwdriver.

Note: Screw should be snug, but do not over tighten.

13

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

UNIT ASSEMBLY PRIOR TO INSTALLATION

NAILING STRIPS

The 6 Standoffs must be correctly positioned and attached before unit is slid into position. The nailing strips come attached to the unit. There is 1 plate on each side and 1 on the top that can be folded out as required.

Secure the top and side nailing strips to the framing.

STANDOFF ASSEMBLY

The standoffs are shipped in a fl at position and must be folded into shape and attached.

1) Remove the standoffs from the fi replace.

2) Take each standoff and bend into the correct shape. Bend up at the bend lines until the screw holes in the standoff and the pre-punched screw holes on the fi replace top line up.

3) Attach the standoff securely to the unit with 2 screws per standoff (on opposite corners).

14

S tandoffs installed.

Note:

Depending on the material used for fi nishing, the nailing strips must be set accordingly so that the fi nished material is always at the 1-1/2" edge of the fl ange.

Nailing Strips

Finished

Material

1/2"

Nailing Strip

Position

1"

Nailing Strip

1” Forward

Unit

1" 1/2"

Nailing Strip

½” Forward

1-1/2"

Unit

0" (fl ush)

Nailing Strip

Flush w/unit

Factory Set

Unit

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

DRAIN INSTALLATION (RECOMMENDED)

Although this fi replace is designed to operate outdoors safely, rain and other sources of moisture may enter the hearth area, which will cause water to collect inside the base of the unit.

To prevent excessive water collection, the installer must provide a way to drain the water from the base of the unit by building or installing a water collector before positioning the fi replace in its location.

INSTALLATION INSTRUCTIONS

When planning for the installation of the unit, the framing height must be increased by 3/4", when installing a drain pan. Additional space below the unit will also be required to plumb a drain line.

1) Remove 4 screws to remove the rear access panel from the back of the unit - this will allow access to the drain hole at the base of the unit.

2) On the exposed drain hole (see location below), install a PVC 3/4" threaded coupling reducer going from the top of the pan, down through the hole.

Apply a silicone-based sealant around the base and threads before installation.

3) Holding the reducer coupling with a wrench, thread a 90° PVC elbow (from the underside of the unit) to the reducer until it is tight to the metal.

Note: To assure proper drainage, that fi replace must be installed on a leveled surface

4) Add additional piping to route the drain to an appropriate location.

Drain hole

Rear access panel

Threaded

Reducer

(PVC)

Cut notches into the top of the coupling reducer to prevent water pooling.

Threaded

Elbow

@ 90°

(PVC)

Reducer and elbow can be purchased from your local hardware store.

Drain hole location at base of the unit

15

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

WALL SWITCH AND BATTERY INSTALLATION

(INCLUDED WITH UNIT)

The unit comes with low voltage wire and a battery extension wire installed.

1) Run supplied wire to desired location - to a max. of 9 feet.

6) Install supplied 4-AA batteries into the battery holder. Using velcro install battery holder to the backside of the battery compartment door. Connect battery terminal.

2) Install supplied electrical box in desired location.

7) Using silicone, completely seal strain relief to protect from water or moisture.

3) Remove center knock out from electrical box and install strain relief

(strain relief nut not required).

Center knock out

8) Place supplied gasket on top of electrical box.

9) Fasten cover to electrical box using supplied screws.

10) Place switch in OFF position until fi nal installation is complete.

Strain Relief

4) Route low voltage wire and battery extension wire through the strain relief.

5) Connect low voltage wire to supplied switch, fasten switch to right side of electrical box (polarity not important).

16

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

WIRING DIAGRAM

This heater does not require a 120V A.C. supply for operation. (Do not cut the ground terminal off under any circumstances.)

NOTE: 4 AA batteries must be installed in the battery pack to operate the burner switch.

Profl ame

880

SureFire™ Switch

Proflame Valve or Optional Wall Switch

Remove the protective coating from the following components before proceeding. Carefully follow stainless handling instructions on following page.

17

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

INNER PANEL INSTALLATION

Before installation, panels must be handled and cleaned as per instructions noted below:

Stainless Steel Panels

•

Stainless panels must be inspected for scratches and dimples prior to installation. All claims to be recorded at this time.

Claims for damage after installation will not receive consideration.

•

To protect the fi nish during installation and handling - cotton gloves MUST be worn at all times while handling the panels (even when removing protective coating).

•

Use a hair dryer or similar device to remove the protective coating from the panels.

•

Stainless panels will discolor a little during normal operation.

This is normal and should not be considered a defect.

* All hand and fi nger marks MUST be cleaned off with a soft cloth and a stainless steel cleaner. Most stainless steel cleaners leave a fi lm/ residue on the surface of the panels. Use an ammonia based cleaner (ie. glass cleaner) to remove this fi lm before applying heat to the unit.

Failure to do this will result in burn stains on panels which you will be unable to remove.

Not protected by product warranty.

1) Install the back panel fi rst - to maneuver the panel into position - tilt the top of the panel forward and position the bottom of the panel in fi rst. Use care - do not scratch the panel when clearing the pilot hood.

3) Install other side panel next. Position side panel and secure with a clip and one screw.

2) Install a side panel next (not important which side goes in fi rst).

Position the panel with the bend in the panel facing towards the outside or wall of the unit. Position side panel and secure with a clip and one screw.

4) Final install - shown below.

18

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

GLASS CRYSTAL INSTALLATION

IMPORTANT NOTE:

Only the supplied approved Glass Crystals and Ceramic Spa are to be used with these fi replaces. Use of any other type of glass crystals or stones can alter the unit's performance, any damage caused by the use of any unapproved glass or stones will not be covered under warranty.

When using Ceramic Spa DO NOT cover burner ports or pilot light that lead to pilot fl ame. Ensure the crystals or stones do not overlap excessively as this will effect the fl ame pattern.

BURNER PACKAGES

Unit *Glass Crystals Ceramic Spa Stones

HZ54E / HZ54EPV 3 lbs

HZ42 / HZ42E / HZ40E 2 lbs

HZ42ST / HZ42STE

HZ42STEPV

2 lbs

1 lb Glass + 2 packages (140 spa stones)

1 lb Glass + 1 package (70 spa stones)

1 lb Glass + 1 package (70 spa stones)

HZ30E **

HZI234E ***

1 lb

3/4 lb

HZI390E/ HZI390EB * 7 lbs [4 lbs burner + 3 lbs fi rebox]

HZI540EB * 8 lbs [4 lbs burner + 4 lbs fi rebox]

HZO42/HZO42 (AUS) 3 lbs

L676S

P33S/P33SE ****

1 lb

1 lbs

1 lb Glass + 1 package (70 spa stones)**

3/4 lb Glass + 1 package 70 spa stones)***

2 lb Glass + 1 package (70 spa stones)

2 lb Glass + 1 package (70 spa stones)

Not Approved

1 package = (70 spa stones)

1 package = (70 spa stones)****

PTO30 */ Plateau Series 10 lbs

PTO60* 20 lbs

U32S / U32SE 1 lb

Not Approved

Not Approved

1 package = (70 spa stones)

E33S 1 lb 1 package = (70 spa stones)

NOTE:

* Glass Crystals are available in 1lb and 5lb bags. All units come standard with Cobalt Blue glass crystals except:

* HZO42 comes with Copper glass crystals.

* HZI390E, HZI390EB, HZI540EB, PTO30, PTO60 & Plateau Series do NOT include glass crystals with units. Must purchase separately.

• 1 Ceramic Spa stone package contains 70 stones.

**

Recommended - use only 40 of the 70 ceramic stones on the HZ30E burner.

***

Recommended - use only 24 of the 70 ceramic stones on the HZI234E burner.

****

Recommended - use only 50 of the 70 ceramic stones on the P33S/P33SE burner.

Glass Crystals shown on Burner

For Units HZ54E, HZ54EPV, HZ42ST, HZ42STE, HZ42STEPV,

HZI234E, HZ42E, HZ42, HZ40E, HZ30E,

HZO42, HZO42 (AUS) PTO30, PTO60 Plateau Series only

Optional Ceramic Spa Stones + Glass Crystals shown on burner.

For Units HZ54E, HZ54EPV, HZ42ST, HZ42STE, HZ42STEPV,

HZI234E, HZ42, HZ42E, HZ40E, HZ30E only

19

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

PEBBLE INSTALLATION

Firebox (Around Burner) Packages

Unit Glass Crystals

HZ54E / HZ54EPV 6 lbs

HZ42 / HZ42E / HZ40E 5 lbs

HZ42ST / HZ42STE / HZ42STEPV 5 lbs

HZ30E

HZI540EB

2 lbs

4 lbs

HZI390E/ HZI390EB

HZI234E

HZO42 / HZO42 (AUS)

P33S / P33SE

U32S / U32SE

E33S

3 lbs

2 lbs

3 lbs

3 lbs

3 lbs

3 lbs

Pebbles

2 packages (6 x bags pebbles)

2 packages (6 x bags pebbles)

2 package (6 x bags pebbles)

1 package (3 x bags pebbles)

1.5 packages (4 x bags pebbles)

1 package (3 x bags pebbles)

1 package (3 x bags pebbles)

1 package (3 x bags pebbles)

1 package (3 x bags pebbles)

1 package (3 x bags pebbles)

1 package (3 x bags pebbles)

There are 2 optional packages to choose from to cover the fi rebox base:

1)

Natural River Pebbles

2) Glass Crystals (4 colors available)

Spread the pebbles / crystals evenly on the exposed base of the fi rebox. Pebbles are NOT to be placed anywhere on the burner or over top of the

Glass Crystals or optional Ceramic Spa Stones.

IMPORTANT NOTE:

Only the supplied and approved pebbles / glass crystals are to be used with these fi replaces. Use of any other type of pebbles, glass crystals or other material can create a danger and will void the warranty.

Natural River Pebbles shown surrounding the a Horizon Burner

20

River Pebbles shown surrounding a Sunrise Burner Glass Crystals shown surrounding the Burner

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

VOLCANIC STONE INSTALLATION

Evenly spread the glass crystals and volcanic stones over the burner. Ensure the stones do not overlap too much as this will effect the fl ame pattern.

IMPORTANT NOTE:

Only the supplied approved Volcanic Stones are to be used with these fi replaces. Use of any other type of stones can alter the unit's performance, any damage caused by the use of any unapproved glass or stones will not be covered under warranty.

When using Volcanic Stones DO NOT cover burner ports or pilot light that lead to pilot fl ame. Ensure the stones do not overlap excessively as this will effect the fl ame pattern.

OUTDOOR VOLCANIC STONE BURNER PACKAGES

Unit Volcanic Stones

Ivory/Tan

Volcanic Stones

Slate/Grey

White Garden Stones

HZO42/HZO42 (AUS) 35 stones w/3lbs glass

PTO30 */ Plateau Series 50 stones w/5lbs glass

PTO60 100 stones w/10lbs glass

35 volcanic stones w/3lbs glass 50 garden stones w/3lbs glass (AUS Only)

50 volcanic stones w/5lbs glass

100 stones w/10lbs glass

NOTE:

* Basalt Volcanic stones are measured by weight not quantity. Each bag contains 15lbs of stones, however the exact quantity and size will vary.

Size varies between 2" - 3".

Volcanic Stones + Glass Crystals

For the PTO30, PTO60

& Plateau Series only

Volcanic Stones Ivory /Tan + Glass Crystals

For the HZO42 & HZO42AUS only

Volcanic Stones Slate /Grey + Glass Crystals

For the HZO42 & HZO42AUS only

21

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

OPTIONAL LOG SET INSTALLATION

Installation of Refl ective Panels must be completed before installing the log set.

Read the instructions below carefully and refer to the images. If the logs are broken do not use the unit until they are replaced.

Broken logs can interfere with pilot operation.

Install 3lbs of glass crystal on the burner (follow glass crystal instruction sheet) before installing logs.

A

Improper positioning of the logs may create carbon build-up and can alter the unit's performance which is not covered under warranty.

B

Log kit # 326-930 contains the following pieces:

Part #

A x 1

B x 1

C x 1

D x 1

E x 1

Description

Log

Log

Log

Log

Log

C

Diagram 1

D

E

F

1) Install logs A and C on the burner as shown below. Orient the logs in the same way and in a similar location on the left side of the burner as depicted in Diagram 2.

A

C

Diagram 2

2) Install log B on the burner as shown below. Orient log B across log A in the same way and in a similar position as depicted in Diagram 3.

A

B

Diagram 3

3) Install log E on the right side of the burner as shown below. Orient log E in the same way and in a similar position as depicted in Diagram 4.

22

Diagram 4

E

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

4) Install log D on the burner as shown below. Orient log D across log E in the same way and in a similar position as depicted in Diagram 5- log

D will rest up against the back panel.

D

E

Diagram 5

5) Install log F on the right side of the burner as shown below. Orient log F in the same way and in a similar position as depicted in Diagram 6.

Diagram 6

F

Final Install

23

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

HEAT DEFLECTOR INSTALLATION

1) Install the heat defl ector to the top inside of the fi rebox with 4 screws as shown below.

Heat Defl ector

24

Heat Defl ector

Installed

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

FACEPLATE INSTALLATION

Remove the protective coating from the faceplate before installation - see handling instructions in panel install section.

1) To install the faceplate - line up the tabs on the faceplate with the 'C' shaped openings on the left and right sides of the unit. There are 3 slots on each tab so the faceplate to accommodate different fi nishing materials.

3) For installations where thicker fi nishing material is used - the optional trim piece may be installed to fi ll the gap.

Install the trim between the bottom access panel and the faceplate as

2) Install logo onto faceplate.

Regency Horizon™ HZO42 Gas Fireplace

4) To remove - reverse steps.

Trim Piece

Final Install

25

INSTALLATION

GLASS WIND SHIELD INSTALLATION

1) To install the glass wind shield - slot it into the space between the burner tray cover and the bottom access panel.

Burner Tray Cover

Glass Wind Shield

Bottom Access panel

WEATHER COVER INSTALLATION / REMOVAL

1) The unit should be covered when not in use for extended periods of time. The soft fabric cover is made of weather resistant material - to protect the unit from the elements. Starting from one corner - slide the cover over the corner, then stretch the cover until it is fi tted over all four corners.

26

CAUTION:

Never start the unit with the cover on.

Let the unit cool before installing the cover.

Turn off gas supply to unit before installing cover.

Weather Cover Installed

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

ASSEMBLY INSTRUCTIONS FOR A STEEL STUD FRAMING KIT FOR HZO42

Follow these instructions to construct a steel stud frame for the Outdoor fi replace;

Overall dimensions = 60" W x 20" D x 52-1/2" H.

**Non-combustible fi nishing board not supplied with kit. Board may be purchased at your local hardware/building supply store.

Tools Required

1 power drill

+ #2 phillips bit

1 hand

#2 screwdriver

(Phillips)

1 level

1 tape measure

326-900 CONTENTS:

Top / Bottom (A) x 2

Vertical Supports - Tall (B) x 8

Vertical Supports - Short (C) x 6

Base (D) x 1

Header

Corner Brace

(E) x 1

(F) x 2

Vertical Support

Wafer Screws

(G) x 1

80

27

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

1) Place top/bottom (A) on the ground - fl at side down. Bend the tabs up to a 90° angle.

3) Line up the screw holes of (A) with (B). Secure

each (B) with 2 wafer screws (one on each side) as shown below.

(A)

(B)

Bend tabs inward to 90°angle.

(A)

Tab locations

2) Position 4 of the (B) pieces with the fl at side of (B) contacting the tab as shown below.

(B)

(A)

4) With all 4 - (B) pieces secured to the bottom with 2 screws

(1 on each side) (A) can be placed into position, as shown below. Ensure all tabs on the (A) are bent to 90° and oriented to each (B) as shown in step 2.

(A)

28

Part B positioned fl at side fl ush with A tab.

Important: (B) - (tall vertical supports) must be positioned as shown to ensure the correct installation of (C).

5) Line up top (A) screw holes with (B) screw holes and secure with (B) to (A) with 2 wafer screws (1 on each side - 8 in total).

Note: Securing inner (B) pieces to top (A) will add rigidity, making it easier to lineup and install outer (B) pieces.

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

6) Manoeuvre remaining (B) pieces and position in each corner of the frame - fl at side facing out - see 2 diagrams below.

9) Position remaining 2 - (C) pieces offset from center rib as shown below.

(C)

7) LIne up screw holes on top / bottom (A) with each (B)- secure with 3 wafer screws each on top and bottom - 6 screws in total for each outer (B) (3 top- 3 bottom).

(B)

10) Position (D) on top of (C) pieces - line up screw holes and secure (D) to (C) with 12 wafer screws.

(D)

(A) location) line up (E) (header) with appropriate screw holes.

8) Position 4 - (C) pieces with the fl at side back to back with the fl at side of each inner Part B as shown below. Secure each

(C) to bottom (A) with 3 wafer screws (one on each side and one at top as shown below.

(C)

(E)

44-11/16"

(C)Screw locations

(B)+ (C) - fl at sides back to back

Regency Horizon™ HZO42 Gas Fireplace

29

INSTALLATION

12) LIne up screw holes on (E) (header) and (B) (inner vertical support). Secure with 2 wafer screws on each side (4 total) as shown below. This will now be the front of the frame.

14) Line screw holes on 1 (F) (corner brace) with (B) + (A) and secure with 4 wafer screws. as shown below.

(A)

(F)

(B)

(E)

15) Repeat step 14 for opposite corner as shown below.

13) On the back side of the frame. Install both (F) pieces (corner brace) on opposite corners.

Important: (F) parts must be installed opposite from one another for rigidity as shown below.

(F)

(B)

(D)

16) Install vertical back support to back of assembly with 2 screws at top and bottom in locations shown below.

30

(F) corner brackets positioned in opposite corners

Note: Confi rm assembly is level and square before proceeding with further materials.

Regency Horizon™ HZO42 Gas Fireplace

INSTALLATION

REMOTE PROPANE / LP GAS ENCLOSURES INSTALLATION GUIDELINES

If the unit is permanently connected to a gas piping system from a remote supply tank, installation must be in accordance with local codes or, in absence of local codes, with the

National fuel Gas codes ANSI Z223/1.NFPA 54.

If constructing an enclosure to conceal the propane / LP cylinder- the enclosure must adhere to the following construction requirements:

(4) ventilation openings at the top and bottom of the enclosure. The openings must adhere to the minimum requirements according to the capacity of the cylinder (see Diagram 1).

allow entrance of a 1/8" (3.2mm) diameter rod.

Enclosures may be constructed with one side completely open OR if the enclosure is built with four (4) sides, a top and a bottom:

• Ventilation openings in side walls must not communicate directly with other enclosures of the appliance.

hand. Connections should be easy to leak test inside the enclosure. A door on the enclosure is acceptable only if easily opened without the use of tools and is non locking.

and spaced at a minimum of 180°. Openings must remain unobstructed.

burner compartment and provide protection from radiation, act as a flame barrier and protect the cylinder from foreign material.

walls of the enclosure within 5" (127mm) of the top of the enclosure. They need to be of equal size, unobstructed and spaced 180° apart. The openings need to be a total area of 1 in² /lb (14.2 cm²/kg) of fuel storage capacity.

square inches (3.23 cm²) for each pound of propane/LP contained in the tank (see example below). nection and inspection of the connection of the LP

- gas cylinder.

tion on the LP cylinder that might be disturbed during installation.

A

Propane / LP Tank Enclosure Specifi cations

A

B

Opening 180° apart from each other

Minimum of 2" (50.8mm) from fl oor/ground to base of tank

C Maximum of 1" (25.4mm) from to base of tank to bottom of opening

5” Max.

5” Max.

Diagram 1

1” Max.

2” Min.

C

B

31

Regency Horizon™ HZO42 Gas Fireplace

OPERATING INSTRUCTIONS

OPERATING

INSTRUCTIONS

FIRST FIRE AERATION

ADJUSTMENT

1) Read and understand these instructions before operating this appliance.

2) Check to see that all wiring is correct and enclosed to prevent possible shock.

3) Check to ensure there are no gas leaks.

The fi rst fi re in your fi replace is part of the paint curing process. To ensure that the paint is properly cured, it is recommended that you burn your fi replace for at least four (4) hours the fi rst time you use it

.

When fi rst operated, the unit will release an odour caused by the curing of the paint, the burning off of any oils remaining from manufacturing.

Open the air shutter for a blue fl ame or close for a yellower fl ame. The burner aeration is factory set but may need adjusting due to either the local gas supply or altitude.

Minimum Air Shutter Opening:

4) Ensure that the stainless panels are installed.

The glass panel may require cleaning after the unit has cooled down.

5) Verify log placement. If the pilot cannot be seen when lighting the unit, the logs have been incorrectly positioned.

6) The unit should never be turned off, and on again without a minimum of a 60 second wait.

DO NOT ATTEMPT TO CLEAN THE

GLASS WHILE IT IS HOT.

CAUTION: Carbon will be produced if air shutter is closed too much.

Note: When the glass is cold and the appliance is lit, it may cause condensation and fog the glass. This condensation is normal and will disappear in a few minutes as the glass heats up.

Note: Any damage due to carboning resulting from improperly setting the aeration controls is NOT covered under warranty.

Note: Aeration Adjustment should only be performed by an authorized FPI Installer at the time of installation or service.

LIGHTING PROCEDURE

1) Turn on ON/OFF switch.

2) Press and release on ON/OFF button once.

3) After approximately 4 seconds the spark ignition system will spark for 60 seconds to light the main burner.

4) The unit will turn on.

Note: The fi rst try for ignition will last approximately

60 seconds. If there is no fl ame ignition (rectifi cation) the board will stop sparking for approximately 35 seconds. After wait time , the board will start second try for ignition by sparking for approximately 60 seconds . If there is still no positive ignition the board will go into lock out.

The system will need to be reset as follows:

a) Turn the system off using ON/OFF switch.

b) After approximately 2 seconds turn on ON/

OFF switch.

c) Unit will repeat step 2.

SHUTDOWN

PROCEDURE

1) Turn ON/OFF switch.

2) If service is to be performed - you must disconnect both sources of power to the unit, the main power and battery.

Regency Horizon™ HZO42 Gas Fireplace

OPERATING INSTRUCTIONS

COPY OF LIGHTING PLATE INSTRUCTIONS

The lighting plate is located on the underside of the front access panel in the unit.

FOR YOUR SAFETY READ BEFORE LIGHTING

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or

Natural Gas and Propane Installation Codes, CSA B149.1.

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or gas supplier.

AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice risquede déclencher un incendie ou une explosion entraînant des dommages, des blessures ou la mort.

Une installation, d'ajustement, de modifi cation, de service ou d'entretien peut provoquer des blessures ou des dommages matériels. Reportez-vous au manuel du propriétaire de l'information fournie avec cet appareil. Pour obtenir de l'aide ou des informations supplémentaires consulter un installateur qualifi é, une agence de service ou fournisseur de gaz.

A) This appliance is equipped with an ignition device which automatically lights the pilot.

Do not try to light the pilot by hand.

B) BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to

the fl oor because some gas is heavier than air and will settle on the fl oor.

WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance.

- Do not touch any electric switch, do not use any phone in your building.

- Immediately call your gas supplier from a neighbours phone. Follow the gas supplier’s instructions

- If you cannot reach your gas supplier, call the fi re department.

A) Cet appareil est muni d’un dispositif d’allumage qui allume automatiquement la veilleuse.

Ne tentez pas d’allumer la veilleuse manuellement.

B) AVANT DE FAIRE FONCTIONNER , renifl ez tout autour de l’appareil pour déceler une odeur

de gaz. Renifl ez près du plancher, car certains gaz sont pluslourds que l’air et peuvent

s’accumuler au niveau du sol.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :

• Ne pas tenter d’allumer d’appareil

• Ne touchez à aucun interrupteur; ne pas vous servir des téléphones se trouvant dans le

bâtiment.

• Appelez immédiatement votre fournisseur de gaz depuis un voisin. Suivez les

instructions du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur, appelez le service des incendies

CAUTION: LIGHTING INSTRUCTIONS

H o t w h i l e i n operation. Do not t o u c h . S e v e r e

Burns may result.

Due to high surface

STOP! Read the safety information on this label.

1) Turn on ON/OFF switch

2) After approximately 4 seconds the spark ignition system will spark for 60 seconds to light the main burner.

s.

t e m p e r a t u r e s

3) The unit will turn on.

k e e p c h i l d r e n ,

Note: The fi rst attempt to ignition will last approximately 60 seconds. c l o t h i n g a n d furniture, gasoline If there is no fl ame ignition (rectifi cation) the board will stop sparking and other liquids for approximately 35 seconds. After this wait time, the board will start having flammable vapors away. Keep a second try for ignition by sparking for approximately 60 seconds.

If there is still no positive ignition after the second attempt the board burner and control compartment clean.

S e e i n s t a l l a t i o n a n d o p e r a t i n g i n s t r u c t i o n s a c c o m p a n y i n g appliance.

will go into lock out.

The system will need to be reset as follows (after going into lock out mode): a) Wait 5 minutes - turn the system off using ON/OFF switch. b) After approximately 2 seconds turn on ON/OFF switch.

c) Unit will repeat step 2.

1) Appuyez le bouton ON / OFF

2) Attendre 4 secondes. Le système d’allumage produira des étincelles pendant 60 secondes afi n d’amorcer le brûleur principal.

3) Les fl ammes s’allumeront.

Remarque : Au premier allumage, le système tente d’allumer les fl ammes pendant 60 secondes. Si l’essai est infructueux, le système fait une pause de 35 secondes.

C’est ce qu'on appelle l'étape de rectifi cation. Ce délai

écoulé, le système tente à nouveau d'allumer les fl ammes en produisant des étincelles pendant 60 secondes. Si les fl ammes ne s’allument toujours pas, le système se met en mode verrouillage.

Il faut alors le réinitialiser en suivant les

étapes ci-dessous (pour le déverrouiller) :

a) Attendre 5 minutes et éteindre l’appareil en réglant l’interrupteur à la position « OFF »;

b) Attendre 2 secondes et rallumer le système

à l’aide de l’interrupteur.

c) L'unité répétera l'étape 2.

1) Turn off ON/OFF switch

2) If service is to be performed - you must disconnect power to the unit, from the battery pack, refer to manual

1)

TO TURN OFF

GAS APPLIANCE

Appuyez sur le bouton ON /

OFF vous devez débrancher l'appareil, du bloc-piles, voir le manuel d'instruction pour plus de détails.

DO NOT REMOVE

THIS INSTRUCTION PLATE

918-892a

33

Regency Horizon™ HZO42 Gas Fireplace

MAINTENANCE

MAINTENANCE INSTRUCTIONS

1) Always turn off the gas valve and unplug the batteries before cleaning. For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year. When cleaning the logs, use a soft clean paint brush as the logs are fragile and easily damaged.

2) Clean appliance with a damp cloth (never when unit is hot). Never use an abrasive cleaner. The glass should be cleaned with a gas fi replace glass cleaner.

3) Hand and fi nger marks should be cleaned off with a soft cloth and a stainless steel cleaner. Most stainless steel cleaners leave a fi lm/

residue on the surface of the panels. Use an ammonia based cleaner (ie. glass cleaner) to remove this fi lm before applying heat to the unit.

Failure to do this will result in burn stains on panels which you will be unable to remove.

4) The heater is fi nished in a heat resistant paint and should only be refi nished with heat resistant paint. Regency ® uses StoveBright Paint - Metallic Black

#6309.

5) Make a periodic check of burner for proper position and condition. Visually check the fl ame of the burner periodically, making sure the fl ames are steady; not lifting or fl oating. If there is a problem, call a qualifi ed service person.

6) The appliance must be inspected before use, and at least annually, by a qualifi ed fi eld service person, to ensure that the fl ow of combustion and ventilation air is not obstructed.

7) Do not use this appliance if any part has been under water. Immediately call a qualifi ed service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. This is not covered under the terms of the warranty policy.

9) Verify operation after servicing.

34

Regency Horizon™ HZO42 Gas Fireplace

MAINTENANCE

VALVE ASSEMBLY REPLACEMENT

1) Turn the unit off and allow it to cool down to room temperature.

2) Turn off the gas supply to the unit.

3) Remove trim.

9) Remove the front access panel by lifting up and out.

4) Remove the faceplate by lifting it up and off the unit.

10) Remove the burner tray by lifting up and out.

5) Remove the glass wind shield by lifting it up and out- place on a soft surface.

11) Remove left and right screws from the burner legs.

6) Remove the screw and panel clip on the right side. Remove the right side panel once the clip has been removed.

7) Remove the screw and panel clip on the left side. Remove the left side panel once the clip has been removed.

8) Remove the back panel once the 2 side panels have been removed.

Regency Horizon™ HZO42 Gas Fireplace

35

MAINTENANCE

12) Slide the burner to the right and lift up and out of the fi rebox.

BATTERY REPLACEMENT

1) Remove the 2 screws securing the battery compartment.

13) Remove the 5 screws securing the Digital Fireplace Burner Control to the fi rebox.

2) Lift the battery compartment upwards.

14) Remove the DFBC from the unit - see Digital Fireplace Burner Control

Removal in this manual.

15) Remove 6 screws an lift out valve tray.

3) Install 4 - AA batteries and reverse steps.

16) Replace with new valve tray and reverse steps. Inspect gasket condition, replace if necessary.

36

Regency Horizon™ HZO42 Gas Fireplace

MAINTENANCE

DIGITAL FIREPLACE BURNER CONTROL

REMOVAL

1) To access to the Digital fi rebox burner control box - follow steps 1-11 from the Valve assembly replacement instructions on pages 35,36.

5) Disconnect the yellow ground wire with green diagonal stripe for pilot

(CN2). See Diagram 4 below.

2) Disconnect the Black Pilot sensor wire with Red Spade connector from the 'ON' on DFBC (Digital fi replace burner control) box.

See Diagram 1 below.

Ground wire Diagram 4

Diagram 1

Pilot Sensor

Wire

3) Disconnect the Black sparker wire with black spade connector from CN3.

See Diagram 2 below.

6) Disconnect the three valve wires (yellow wire with green stripe).

See Diagram 5 below.

Valve wire

Diagram 5

Diagram 2

Sparker Wire

4) Disconnect the white and green On/Off switch wires.

See Diagram 3 below.

White

Green

Diagram 3

ON/OFF wires

37

Regency Horizon™ HZO42 Gas Fireplace

PARTS LIST

Part #

1) 326-552

Description

Faceplate Assembly

2) 326-009

3) 940-368/P

4) 326-525

326-525

Heat Defl ector

Wind Shield

Burner Assembly NG

Burner Assembly LP

5) 904-777 Orifi ce # 29 (NG)

904-434 Orifi ce # 47 (LP)

MAIN ASSEMBLY

326-028

326-036

326-037/F

948-223

326-940

910-363

918-882

6) 326-574/P

326-576/P

Valve Assembly NG

Valve Assembly LP

7) 326-007/P Front access panel

8) 326-048 Burner Tray Cover

Pilot Hood

Top nailing strip

Side nailing strip

Logo Plate

Weather Cover

Wall switch

Manual

2

8

38

1

3

4

7

6

5

Regency Horizon™ HZO42 Gas Fireplace

Part #

9) 326-525

326-525

10) 911-024

911-025

11) 326-008

Description

Valve NG SIT 880

Valve LP SIT 880

Burner Tray Cover

Burner Assembly NG

Burner Assembly LP

12) 911-006

911-007

Pilot Assembly - NG

Pilot Assembly - LP

Flame Sensor

Igniter

BURNER ASSEMBLY

Part # Description

904-777 Orifi ce #29 NG

904-434 Orifi ce #47 LP

Log Set 326-930

PARTS LIST

9

Regency Horizon™ HZO42 Gas Fireplace

11

10

12

39

PARTS LIST

Part #

13) 326-907

14) 940-368/P

15) 326-552

946-676

946-695

Description

Refl ective Stainless Steel Inner Panels

Glass windshield

Faceplate Brushed Stainless

Copper Glass Crystals

Garden Stones

ACCESSORIES

40

15 14

13

Regency Horizon™ HZO42 Gas Fireplace

NOTES

Regency Horizon™ HZO42 Gas Fireplace

41

NOTES

42

Regency Horizon™ HZO42 Gas Fireplace

WARRANTY

Regency ® Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit thoroughly before it leaves our facility. FPI Fireplace Products International Ltd. is pleased to extend this limited warranty to the original purchaser of a Regency ® Product. This warranty is not transferable.

Limited Warranty:

The gas valve, burner tube, pilot assembly, fl ame sensor, electrode, control modules, switches and wiring for battery compartment are all covered for (2) two years on parts and (1) one year on subsidized* labor only against defect in manufacture, from date of purchase.

Ceramic logs, volcanic stones, glass crystals, and tempered glass wind shield carry a (1) one year warranty against manufacturing defect, on parts, with no labor allowance, from date of purchase.

Special fi nishes such as stainless steel components are not covered against environmental damage including corrosion, misuse, cleaning or handling issues that cause discoloration. To receive consideration any damage claim against stainless steel components must be submitted at the time of installation. Damage from abrasive cleaners and discolouration to stainless components caused by heat, are not covered under warranty. Damage reported after installation will not be covered.

Repair/replacement parts purchased by the consumer from FPI after the original coverage has expired on the unit will carry a 90 day warranty, valid only with a receipt. Any item shown to be defective will be repaired or replaced at our discretion. No labor coverage is included with these parts.

Conditions:

Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at FPI's option, through an accredited distributor or agent provided that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.

It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated for manufacturer defect.

The authorized selling dealer is responsible for all in-fi eld service work carried out on your Regency ® product. FPI will not be liable for results or costs of workmanship from unauthorized service persons or dealers.

At all times FPI reserves the right to inspect product in the fi eld which is claimed to be defective.

All claims must be submitted to FPI by authorized selling dealers. It is essential that all submitted claims provide all of the necessary information including customer name, purchase date, serial #, type of unit, problem, and part or parts requested, without this information the warranty will be invalid.

Exclusions:

Batteries are not covered under warranty policy.

At no time will FPI be liable for any consequential damages which exceed the purchase price of the unit. FPI has no obligation to enhance or modify any unit once manufactured. ie. as products evolve, fi eld modifi cations or upgrades will not be performed.

FPI will not be liable for travel costs for service work.

Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this warranty policy.

Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy.

The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse, improper installation, negligence or problems caused by environmental or geographical conditions, inadequate ventilation.

Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer.

FPI will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance.

Malfunction | damage of this appliance due to mother nature (wind, rain, snow, etc.) is not covered under the terms of the warranty policy.

Performance problems due to operator error will not be covered by this warranty policy.

Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from FPI, may create a danger and nullify your warranty on this product.

Any alteration to the unit which causes sooting or carboning that results in damage to the interior / exterior facia is not the responsibility of FPI.

* Subsidy according to job scale as predetermined by FPI.

43

Regency Horizon™ HZO42 Gas Fireplace

Register your Regency

®

warranty online www.regency-fi re.com

Reasons to register your product online today!

• View and modify a list of all your registered products.

• Request automatic email notifi cation of new product updates.

• Stay informed about the current promotions, events, and special offers on related products.

Installer: Please complete the following information

Dealer Name & Address: ______________________________________________

___________________________________________________________________

Installer: ___________________________________________________________

Phone #: ___________________________________________________________

Date Installed: ______________________________________________________

Serial No.: __________________________________________________________

Regency Horizon is a trademark of FPI Fireplace Products International Ltd.

© Copyright 2013, FPI Fireplace Products International Ltd. All rights reserved.

Printed in Canada