advertisement
6654_C170_UG.QXD 4/20/04 3:11 PM Page 1
InFocus Corporation
27700B SW Parkway Avenue
Wilsonville, Oregon 97070-9215
1-800-294-6400 • 503-685-8888
Fax: 503-685-8887 http://www.infocus.com
In Europe:
InFocus International B.V.
Strawinskylaan 585
1077 XX Amsterdam,The Netherlands
Phone: +31 20 579 2000
Fax: +31 20 579 2999
In Asia:
InFocus Systems Asia Pte Ltd.
238A Thomson Road
#18-01/04 Novena Square
Singapore 307684
Telephone: (65) 6334-9005
Fax: (65) 6333-4525
> > > > > > >
User’s
Guide
Declaration of Conformity
Manufacturer: InFocus Corporation, 27700B SW Parkway Avenue, Wilsonville,
Oregon 97070 USA
European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands
We declare under our sole responsibility that this projector conforms to the following directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000
May, 2004
Trademarks
Microsoft, PowerPoint, Word, Excel and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated. InFocus, ASK Proxima, LiteShow, Lite-
Port, and LP are trademarks or registered trademarks of InFocus Corporation.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to take adequate measures. The typical use is in a conference room, meeting room or auditorium.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Agency Approvals
UL, CUL, TUV, GOST
Other specific Country Approvals may apply, please see product certification label.
This user’s guide applies to models C170 and GEN205.
InFocus reserves the right to alter product offerings and specifications at any time.
2
Table of Contents
First-time projector use with Windows 98
Cleaning the lamp filter screens
Red LED behavior and projector errors
If you are experienced in setting up presentation systems, use the included
Quick Set Up card. For complete details on connecting and operating the projector, refer to this User’s Guide. Electronic versions of this User’s Guide in multiple languages are available on the included CD and on our website.
The most current versions can be found on our website.
The website also has technical specifications (an interactive image size calculator, laptop activation commands, connector pin outs, a glossary, the product data sheet), a web store to buy accessories, and a page for online registration. See the inside of the back cover for a list of all relevant web addresses.
3
Important Operating Considerations for Safety
• Place the projector in a horizontal position no greater than 15 degrees off axis.
• Locate the projector in a well-ventilated area without any obstructions to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents.
• Locate the projector at least 4' (1.2 m) away from any heating or cooling vents.
• Use only approved ceiling mounts.
• Use only the power cord provided. A surge-protected power strip is recommended.
• Refer to this manual for proper startup and shutdown procedures.
• In the unlikely event of the lamp rupturing, discard any edible items placed in the surrounding area and thoroughly clean the area along all sides of the projector. Wash hands after cleaning the area and handling the ruptured lamp. This product has a lamp which contains a very small amount of mercury. Dispose of it as required by local, state or federal ordinances and regulations. For more information see www.eiae.org
.
Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to follow these instructions may affect the warranty. For complete details of the warranty, see the Warranty section at the end of this user's guide.
Do not place objects or people in the 2 foot (.6m) area along the side of the projector.
For ceiling mount applications, this area should be 5 feet (1.5m).
2 ft (.6m)
5 ft (1.5m)
4
Introduction
Your new digital projector provides computer and video inputs and has
XGA 1024x768 resolution. The projector is easy to connect, easy to use, and easy to maintain. An Interactive Display on the top of the projector gives you constant feedback on the status of the projector.
Online Registration
Register your projector on our website to receive product updates, announcements, and registration incentives. See the inside of the back cover for the web address.
Included items carry case
Projector components and features remote control receiver (IR) elevator foot release focus keypad speaker zoom
Interactive display projector remote lens cap documentation lens cap tether* audio cable audio cable adapter computer cable power cable video cable
*The lens cap tether ships in the Documentation Pack. Attach it to the lens cap and the projector if desired.
connectors leveling foot
IR receiver
IR receiver heat vent
5
Connector Panel
The projector provides computer and video connectors:
• one M1-D/A (HD, DVI, and computer)
• one VESA (HD, HD component, and computer)
• one S-video
• one composite RCA video
• one audio in/one audio out
It also has an RS-232 serial connector for serial control. The Command Line
Interface (CLI) specifications and commands are on our website.
Connector panel
M1-D/A computer
VESA in/ monitor out
USB JPEG composite video s-video
RS-232 serial control power connector lock audio external speaker
(audio out)
The projector also has a LitePort
TM
USB connector (Type A) and player for
JPEG (Joint Photographic Experts Group, .jpg, .jpe, or .jpeg) images. This allows you to display any JPEG image automatically, without a computer connected. Use your own JPEGs from your digital camera, or convert your files, such as Microsoft
PowerPoint TM
, Word
TM
, or Excel
TM
files, into
JPEGs using LitePort Utility (included on the CD), which allows you to easily generate the highest quality JPEG images possible. Then transfer the
JPEG images from your computer to the projector using a USB mass storage device and your images are ready to be displayed. (Please refer to the Service and Support section of our website for advanced specifications on the
USB device and JPEG files.) You can use the remote control to select which
JPEGs to view (page 27) or you can set up the LitePort player using the Lite-
Port onscreen menu to select display preferences and automatically display
and advance your JPEGs (page 36).
Wireless Projection
You can use the projector’s M1 connector along with the InFocus
LiteShow
wireless adapter and software for cable-free digital projection.
Contact an authorized InFocus dealer or visit the website listed on the back inside cover of this User’s Guide for more information.
6
Connecting a computer
Required computer connections
Connect the black end of the computer cable to the Computer 1 connector on the projector. Connect the blue end to the video port on your computer. If you are using a desktop computer, you first need to disconnect the monitor cable from the computer’s video port.
Some Macintosh computers do not have a standard VESA-out video port.
If the supplied computer cable will not connect to your computer, purchase the appropriate adapter from your Apple reseller.
Connect the black power cable to the connector on the back of the projector and to your electrical outlet.
The Power LED on the projector’s keypad turns solid green.
NOTE : Always use the power cable that shipped with the projector. connect computer cable connect power cable
Optional computer connections
To advance slides in a PowerPoint™ presentation using the remote, plug the
USB connector on the computer cable into the USB mouse connector on your computer. USB drivers must be installed to use the USB feature. For
more information, see page 11.
To have sound with your presentation, connect the audio cable to your computer and to the Audio In connector on the projector. connect computer cable connect audio cable
7
If you are using a desktop computer and want to see the image on your computer screen as well as on the projection screen, plug the monitor cable to the black Computer 2 connector on the projector. This connector can be used as monitor out or VESA in. The default is VESA in, so you must
change this option in the menu to use monitor out. See page 34 to switch
between the two functions.
If you prefer connecting your projector to your computer with an optional
VESA cable, connect one end of the cable to the VESA port on your computer, and connect the other end of the cable to the blue Computer 2 connector on the projector.
This connector can be used as monitor out or VESA in. The default is VESA in.
You can control the projector from an LCD control panel or computer by connecting an RS-232 cable to the projector’s Serial Control connector. Specific RS-232 commands can be found in the Service and Support section of our website.
connect monitor cable connect VESA cable connect RS-232 cable
You can play JPEGs using the LitePort USB connector and LitePort player.
You need a USB mass storage device to use this connector. See page 27 for
details.
connect USB mass storage device
8
Displaying a computer image
Remove the lens cap.
remove lens cap
Press the Power button on the top of the projector or the remote.
The LED flashes green and the fans start to run. When the lamp comes on, the startup screen is displayed and the LED is steady green. It can take a minute for the image to achieve full brightness. The Interactive Display on the projector indicates the startup status.
? No startup screen?
press Power button turn on computer
Turn on your computer.
The computer’s image should appear on the projection screen. If it doesn’t, press the Source button on the projector’s keypad.
Make sure your laptop’s external video port is active.
Many laptops do not automatically turn on their external video port when a projector is connected. Usually a key combination like FN + F8 or CRT/LCD key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the labeled function key simultaneously. Refer to your laptop’s documenta-
tion to learn your laptop’s key combination.
? No computer image? Try pressing the Auto Image
button on the keypad. Get help on page 17.
activate laptop’s external port
9
First-time projector use with Windows 98
If you are running Windows 2000, Windows ME, or Window XP, skip these
steps and go to “Adjusting the image” on page 12.
The first time you connect a computer running Windows 98 to the projector, the computer recognizes the projector as “new hardware” and the Add
New Hardware Wizard appears. Follow these instructions to use the Wizard to load the correct driver (which was installed with your Windows operating system).
a Click Next to begin searching for the driver.
a b b Make sure “Search for the best driver” is selected, then click Next.
c Uncheck any checked boxes, then click Next. Windows automatically locates the driver. If this driver has been removed, reload the driver using your Windows operating system CD.
c d d When Windows finds the driver, you are ready to install it. Click Next.
10
Skip this page if you did not connect the USB portion of the M1 computer cable
For Windows 98:
• If you connected the USB cable, the Add New Hardware Wizard appears again. Drivers must be installed to use the USB functionality.
• The Wizard launches two times .
The first time it detects a USB Human Interface Device (for the keyboard).
The second time it detects a USB Human Interface Device (for the mouse).
For Windows 2000, Windows ME, and Windows XP:
• The USB drivers are automatically installed.
11
Adjusting the image
Adjust the height of the projector, if necessary, by pressing the release button to extend the elevator foot.
Rotate the leveling foot (located at the bottom back right corner), if necessary.
Position the projector the desired distance from the screen at a 90 degree angle to the screen.
See page 44 for a table listing screen sizes and distances.
adjust height elevator foot adjust distance
Adjust the zoom or focus rings by rotating them until the desired image size and focus are produced.
adjust zoom and focus
The projector has an Auto Keystone option that is turned on by default. But if the image is not square, adjust the vertical digital keystone by using the buttons on the keypad. Press the upper Keystone button to reduce the upper part of the image, and press the lower Keystone button to reduce the lower part.
You can also adjust the keystone via the menus, or turn off Auto Keystone.
Adjust the Contrast or Brightness in the Picture menu.
See page 30 for help with the menus.
adjust keystone adjust Contrast or Brightness
12 release button rotate leveling foot focus zoom contrast brightness
Connecting a video device
Standard video connections
Plug the video cable into the video-out connector on the video device. Plug the other yellow connector into the yellow Video 2 connector on the projector.
Plug the white connector of the audio adapter into the left audio out connector on the video device and plug the red connector into the right audio out connector on the video device.
Plug the audio cable into the other end of the audio cable adapter and into the audio in connector on the projector.
connect video and audio cables
Connect the black power cable to the connector on the back of the projector and to your electrical outlet. connect power cable
NOTE : Always use the power cable that shipped with the projector.
Optional video connections
If the video device uses a round, four-prong S-video connector, plug an
S-video cable (sold separately) into the S-video connector on the video device and into the S-Video 1 connector on the projector. Use the audio connectors as described directly above.
To connect a progressive scan EDTV or HD source, use the Component to
M1 adapter (sold separately).
connect S-video and audio cables
13
Displaying a video image
Remove the lens cap. remove lens cap
Press the Power button on the top of the projector or the remote.
The LED flashes green and the fans start to run. When the lamp comes on, the startup screen is displayed and the LED is steady green. It can take a minute for the image to achieve full brightness. The Interactive Display on the projector indicates the startup status.
? No startup screen?
Plug in and turn on the video device.
The video device’s image should appear on the projection screen. If it doesn’t, press the Source button on the keypad. press Power button turn on video device
Adjust the height of the projector by pressing the release button to extend the elevator foot. Rotate the leveling foot, if necessary. adjust height elevator foot
Position the projector the desired distance from the screen at a 90 degree
angle to the screen. See page 44 for a table listing screen sizes and distances
to the screen.
adjust distance
14 release button rotate leveling foot
Adjust the zoom or focus rings by rotating them until the desired image size and focus are produced.
adjust zoom and focus
If the image is not square, adjust the vertical keystone using the buttons on the keypad.
Press the upper Keystone button to reduce the upper part of the image, and press the lower Keystone button to reduce the lower part.
You can also adjust the keystone via the menus, or set the projector to auto-
matically adjust the keystone. See page 31.
Adjust the volume on the keypad or remote.
adjust keystone adjust volume
Adjust the Contrast, Brightness, Color, or Tint in the Picture menu.
See page 30 for help with the menus.
adjust Picture menu focus zoom
15
Shutting down the projector
The projector automatically blanks the screen after no active source is detected for 30 minutes. This blank screen helps preserve the life of the projector. The image returns when an active source is detected or a remote or keypad button is pressed. The Interactive Display on the projector indicates the shutdown status.
Screen Save
You can make the blank screen appear after five minutes by turning on
Screen Save in the Settings>System menu. See page 35. There are six time
options for the Screen Save feature. They range from five minutes to 30 minutes with five minute intervals.
Power Save
The projector also has a Power Save feature that automatically turns the lamp off after no signal is detected for 20 minutes. After 10 additional minutes with no signal, the projector powers down. If an active signal is received before the projector powers down, the image is displayed. You must press the Power button to display an image after 30 minutes have
passed. When Power Save is enabled, Screen Save is disabled. See page 35.
Turning off the projector
To turn off the projector, press the Power button and verify that you want to turn the projector off by pressing the Power button again within 3 seconds.
You can cancel the shutdown by not pressing the Power button a second time. The lamp turns off and the LED blinks green for 1 minute while the fans continue to run to cool the lamp. When the lamp has cooled, the LED lights green and the fans stop. Unplug the power cable to completely power off the projector.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section
(page 26). If it does not, troubleshoot the setup. The Interactive Display and
LED on top of the projector indicate the state of the projector and can help you troubleshoot.
Table 1: LED behavior and meaning
LED color/behavior solid green blinking green blinking red
see page 44 for more information
solid red
Meaning
The projector is plugged in, or the projector has been powered on and the software has initialized. The projector has been turned off and the fans have stopped.
The power button has been pressed and the software is initializing, or the projector is powering down and the fans are running to cool the lamp.
A fan or lamp failure has occurred. Make sure the vents aren’t blocked (see
page 23). Turn off the projector and wait
one minute, then turn the projector on again. If the Replace Lamp message appears, replace the lamp and reset the lamp timer. Contact Technical Support if the problem persists .
An unidentifiable error: please contact
Technical Support.
The following tables show common problems. In some cases, more than one possible solution is provided. Try the solutions in the order they are presented. When the problem is solved, you can skip the additional solutions.
16
Source Troubleshooting
Problem Solution
No startup screen
Plug power cable in, press Power button.
Remove lens cap.
Result
Correct image
Only startup screen appears
A
Press the Source button
Activate laptop’s external port
Computer image projected
A
A or restart laptop
17
No computer image, just the words “Signal out of range”
Adjust computer refresh rate in Control
Panel>Display>Settings>Advanced>
Adapter (location varies by operating system)
A
Computer image projected
A
A
For PC: Image fuzzy or cropped
A
You may also need to set a different resolution on your computer, as shown in the following problem, “Image fuzzy or cropped”
Set your computer’s display resolution to the native resolution of the projector
(Start>Settings>Control
Panel>Display>Settings tab, select
1024x768)
For a laptop, disable laptop monitor or turn-on dualdisplay mode
Image clear and not cropped
A
18
For Macintosh: Image fuzzy or cropped
A
Set your computer’s display resolution to the native resolution of the projector
(Apple menu>System
Preferences>Displays, choose 1024x768)
Image clear and not cropped
A
Only my laptop’s background appears, not the
Desktop icons
A
A
Disable “Extend my Windows Desktop” in
Control Panel>Display>Settings>Display 2
(location varies by operating system)
Background and Desktop projected
A
A
Uncheck this option, then click Apply
19
The video embedded in my PowerPoint presentation does not play on the screen
A
B
A
Turn off the internal LCD display on your laptop
Embedded video plays correctly
A
B
Remote control not advancing PowerPoint slides
Connect USB cable (page 7) then load USB
Remote advances slides
See page 26 for information on the remote
X
20
Projector troubleshooting
Problem Solution
Image not square
Result
Adjust keystone on keypad or Picture menu Square image
Image not sharp Adjust the focus lens or Sharpness in the
Picture>Advanced menu
Correct image
A B
Change aspect ratio to 16:9 in
Picture>Aspect ratio menu
Correct image
Image does not fit 16:9 screen
21
Image upside down
Image reversed left to right
A B
A
Projected colors don’t match source
COLOR
Correct image
Turn off Auto Ceiling or Ceiling in
Settings>System menu
Turn off Rear in Settings>System menu
Correct image
A B
Correct image
A B
Adjust color, tint, color temperature, brightness, contrast in the menus
COLOR
22
Image not centered on screen Move projector, adjust zoom, adjust height zoom
Correct image
Adjust horizontal or vertical position in
Picture>Advanced menu
Lamp won’t turn on, LED blinking red (page 16)
Make sure vents aren’t blocked; allow projector to cool for one minute blinks red
Unplug projector; wait one minute; plug in projector and turn it on: lamp lights
23
Lamp won’t turn on, LED blinking red (page 16)
blinks red
Lamp must be replaced (page 40)
Lamp turns on
Still having problems?
If you need assistance, visit the Service and Support section of our website or call us. See the inside of the back cover for a list of all relevant web addresses.
This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its full value.
24
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of their functions: power
–turns the projector on (page 9) and off (page 16).
menu
–opens the on-screen menus (page 30).
select
–confirms choices made in the menus (page 30).
up/down arrows
–navigates to and adjusts settings in the menus (page 30).
auto image –resets the projector to the source.
presets
–cycles through the available preset settings (page 32).
keystone
–vertical keystone adjusts the squareness of the image (page 12).
You can also adjust the keystone via the menus. See page 31.
volume
source –changes the active source. menu navigation buttons
25
Using the remote control
The remote uses two (2) provided AA batteries. They are easily installed by sliding the cover off the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover.
To operate, point the remote at the projection screen or at the projector (not at the computer). The range of optimum operation is about 30 feet (9.14m).
Previous and Next buttons allow you to navigate through your PowerPoint presentation while in Slide Show mode. Connect the USB connector on the computer cable to your computer to use these buttons. When you do this for
the first time, the Add New Hardware wizard may appear. See page 10 for
details on loading the correct USB drivers.
Press the remote’s Menu button to open the projector’s menu system. Use the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 30 for more info on the menus.
The remote also has a Power button to turn the projector on and off (see
page 16 for shutdown info), Volume and Mute buttons to control the sound,
and a Source button to switch between sources.
Two presentation-specific features are also provided. Use the Blank button to display a blank screen instead of the current slide (you can choose which
color is displayed, see page 37); use the Effect button to invoke a user-defin-
able action, such as freeze or aspect ratio (see page 38 to learn to program
this button).
previous button navigation buttons next button
Troubleshooting the remote
• Make sure the batteries are installed in the proper orientation and are not dead. The LED at the top of the remote lights when any button is pressed when the battery power is adequate.
• Make sure you’re pointing the remote at the projector, not the computer, and are within the remote range of 30 feet (9.14m).
• If you are trying to advance PowerPoint slides, make sure the USB portion of the M1 computer cable is connected and the correct drivers are installed.
26
Using the LitePort player
thumbnail on the screen and pressing Next or Down arrow. You are looped back to Folder 1 when you reach the end of the folder list.
LitePort allows you to display any JPEG image automatically, without a computer connected. Use your own JPEGs from your digital camera, or convert your files, such as PowerPoint or Word files, into JPEGs using LitePort
Utility (included on the CD). LitePort Utility allows you to easily generate the highest quality JPEG images possible. (LitePort player is optimized to display images at 960x720 resolution, so for best results, create JPEGs at this resolution). Then transfer the JPEG images from your computer to the projector using a USB mass storage device and your images are ready to be displayed. You can use the remote control to select which JPEGs to view or you can set up the LitePort player using the LitePort onscreen menu to select display preferences and automatically display and advance your JPEGs. See
When active, the player can be in one of three modes:
• Folder View mode , which shows a thumbnail image representing each folder that contains a valid JPEG. The thumbnail for that folder is the first JPEG alphabetically in that folder. Folders are sorted alphabetically based on the name of the actual directory with no regard to the file system path to the folder.
• File View mode , which shows a thumbnail of the valid JPEGs in that folder.
• Full Screen mode , which shows the first JPEG in the selected folder.
The remote and keypad buttons interact with the player differently in each mode. When you insert a USB device in the LitePort connector, the player enters Full Screen mode if Auto Play is checked (the default setting) and the
AutoPlay folder contains a JPEG or it enters Folder View if Auto Play is not checked. The AutoPlay folder is automatically created by LitePort Utility.
See its online help for details.
Folder 1
4
7
Table 2: Folder View navigation
2
5
8
File 1
4
3
6
In File View mode, pressing Next (or Down) places the selection box around the next JPEG file, pressing Previous (or Up) places the selection box around the previous JPEG, pressing Select selects the current JPEG and enters Full
Screen mode, or, if the “return to folders” arrow is highlighted, returns to
Folder View mode. Eight file thumbnails can be displayed on the screen at a time. If your folder contains more than 8 folders, you can navigate to them by navigating to the last thumbnail on the screen and pressing Next. You are looped back to File 1 when you reach the end of the file list.
Return to
Table 3: File View navigation
Folders arrow
3
6 7
Folder 9 (press Next to access Folder 10)
2
5
File 8 (press Next to access File 9)
In Folder View mode, pressing the Next button (or the Down arrow) places the white selection box around the next folder, pressing the Previous button
(or the Up arrow) places the selection box around the previous folder, pressing Select selects the current folder and enters File View mode. Nine folder thumbnails can be displayed on the screen at a time. If your USB drive contains more than 9 folders, you can navigate to them by navigating to the last
27
In Full Screen mode, pressing Next (or Down) advances to the next JPEG file, pressing Previous (or Up) goes to the previous JPEG file, pressing Select returns File View mode. To rotate the JPEG 90 degrees clockwise, select Lite-
Port Rotate in the Effect menu (see page 38) then press the Effect button.
Press Select to return to File View mode.
Using the audio
To play sound from the projector, connect your source to the Audio In connector on the projector.
To adjust the volume, use the buttons on the keypad or remote.
To adjust the balance or turn off the projector’s chime, use the Audio menu
To mute the sound, press the Mute button on the remote.
Troubleshooting audio
If there is no sound, check the following:
• Make sure the audio cable is connected.
• Make sure mute isn’t active.
• Make sure the volume is turned up enough. Press the Volume button on the keypad or remote.
• Adjust the audio source.
• If playing a video, make sure the playback has not been paused.
connect audio cable adjust volume
Connecting external speakers
The projector can be attached to external speakers that have their own power source by plugging a speaker cable into the projector’s Audio Out connector. external speakers speaker cable
28
Optimizing computer images
After your computer is connected properly and the computer’s image is on the screen, you can optimize the image using the onscreen menus. For gen-
eral information on using the menus, see page 30.
• Adjust the Keystone, Contrast, or Brightness in the Picture menu.
•
Change the Aspect Ratio. See page 31 for details.
• Adjust the Color Space, Temperature or Control in the Advanced menu.
• Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced menu.
• Once you have optimized the image for a particular source, you can save the settings using Presets. This allows you to quickly recall these
Optimizing video images
After the video device is connected properly and the image is on the screen, you can optimize the image using the onscreen menus. For general informa-
tion on using the menus, see page 30.
• Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
• Change the Aspect ratio. Aspect ratio is the ratio of the image width to image height. TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your
• Select a Sharpness, Color Temperature, or Video Standard setting. See
•
Adjust the Color Control or White Peaking settings. See page 33.
Presentation features
Customizing the projector
Several features are provided to make giving presentations easier. The fol-
lowing is an overview, details are found in the menu section on page 30.
You can customize the projector for your specific setup and needs. See
page 34 to page 39 for details on these features.
• The remote’s Effect button allows you to assign various features to the key. The default effect is About. You can select from Blank, Mute,
Aspect Ratio, Source, Auto Image, Freeze, About, and LitePort Rotate.
• For rear projection, turn Rear mode on in the Settings>System menu.
• For ceiling mounted projection, turn Ceiling mode on in the Set- tings>System menu.
• Turn on Automatic Keystone adjustments.
• The Freeze effect allows you to freeze the displayed image. This is useful if you want to make changes on your computer without your audience seeing them.
• Specify which source the projector checks first for active video during power-up.
• The Blank button on the remote allows you to display a blank screen
instead of the active source. See page 37.
• Specify the function of the Effect Key on the remote.
• Turn the projector’s display messages on and off.
• The Startup Logo menu option lets you change the default startup
screen to a black, white, or blue screen. See page 37.
• Turn on power saving features.
• Specify blank screen colors and startup logos.
• Two menu options, Power Save and Screen Save, are provided to automatically shut down the projector after several minutes of inactivity or
display a blank screen. This helps preserve lamp life. See page 35.
• Specify the menu language.
•
Project wirelessly with LiteShow wireless adapter. See page 6.
29
•
Control your projector using RS-232 commands. See page 8.
Using the menus
To open the menus, press the Menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to highlight the desired submenu, then press the Select button.
To change a menu setting, highlight it, press Select, then use the up and down arrow buttons to adjust the value, select an option using radio buttons, or turn the feature on or off using check boxes. Press Select to confirm your changes. Use the arrows to navigate to another setting. When your adjustments are complete, navigate to Exit, then press Select to go to the previous menu; press the Menu button at any time to close the menus.
Dots appear before the menu name. The number of dots indicate the menu’s level, ranging from one (the Main menu) to four (the most nested menus).
The menus are grouped by usage:
• The Picture menu provides image adjustments.
• The Settings menu provides set-up type adjustments that are not changed often.
• The About menu provides a read-only display of information about the projector and source.
Certain menu items may be grayed out until a particular source is connected. For example, Sharpness is only available for video sources and will be hidden when a computer source is active. Other menu items may be grayed out when they are not available. For example, Brightness is grayed out until an image is active.
Main menu
Picture menu
Menu button
Keypad navigation buttons
Dots
Settings menu
About menu
30
Picture menu
To adjust the following six settings, highlight the setting, press Select, use the up and down arrows to adjust the values, then press select to confirm the changes.
Keystone : adjusts the image vertically and makes a squarer image. You can also adjust keystone from the keypad. If you want the projector to automatically adjust the keystone, check the Auto Keystone check box. If you then manually adjust the keystone, Auto Keystone is turned off. When the projector is in Ceiling Mount mode, Auto Keystone is turned off. You can do a
“one-time” automatic keystone adjustment by pressing both Keystone buttons on the keypad at the same time.
Contrast : controls the degree of difference between the lightest and darkest parts of the picture and changes the amount of black and white in the image.
Brightness : changes the intensity of the image.
Color : (video and component sources only) adjusts a video image from black and white to fully saturated color.
Tint : (NTSC video sources only) adjusts the red-green color balance in the image.
Aspect Ratio : Aspect ratio is the ratio of the image width to image height.
TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are
1.78:1, or 16:9. The default is 4:3, which displays the input resized up or down to fill the display area.
The aspect ratio selection is saved for each source.
31 increasing keystone decreasing keystone
Aspect Ratio
Presets : The provided Presets optimize the projector for displaying computer presentations, photographs, and film images. You can use the preset as a starting point, then further customize the settings for each source. To restore the factory default settings, choose Factory Reset in the Set- tings>Service menu.
There are also three user-definable presets. To set a preset for the current source, adjust the image, then choose Save User 1, 2, or 3. You can recall these settings in the future by selecting the appropriate user presets.
Presets
32
Advanced settings
Sharpness : (video sources only) changes the clarity of the edges of a video image. Select a sharpness setting.
Color Space : This option applies to computer sources. It allows you to select a color space that has been specifically tuned for the video input.
When Auto is selected, the projector automatically determines the standard.
To choose a different setting, turn off Auto, then choose RGB for computer sources, choose either REC709 or REC601 for component sources.
Color Temperature : changes the intensity of the colors. Select a listed value.
Color Control : allows you to individually modify each color. Highlight the color, press Select, then use the arrows to adjust the value.
Video Standard : (video sources only) When it is set to Auto, the projector attempts to pick the video standard automatically based on the input signal it receives. (The video standard options may vary depending on your region of the world.) If the projector is unable to detect the correct standard, the colors may not look right or the image may appear “torn.” If this happens, manually select a video standard by selecting NTSC, PAL, or SECAM from the Video Standard menu.
Overscan : (video sources only) removes noise around the video image.
Sync Threshold Adjust : (enhanced and high definition sources only) If a hardware device, such as a DVD player, is not syncing properly with the projector, select this option to help it sync.
The following 4 options are for computer and component sources only.
Phase : adjusts the horizontal phase of a computer source.
Tracking : adjusts the vertical scan of a computer source.
Horizontal/Vertical Position : adjusts the position of a computer source.
White Peaking : (video sources only) adjusts the white level processed in the image. It increases the brightness of whites that are near 100%.
33
Advanced
Color Space
Video Standard
Color Temperature
Sharpness
Color Control
Settings menu
Audio : allows adjustments to the volume and balance, and turns the projector’s startup Chime on and off.
Sources : allows you to assign a particular input to a specific source key when using the optional Integrator remote. Also allows selection of a default Power-up Source and enables or disables Autosource.
Sources>Power-up Source: this determines which source the projector checks first for active video during power-up.
Sources>Autosource: When Autosource is not checked, the projector defaults to the source selected in Power-up Source. If no source is found, a blank screen displays. When Autosource is checked, Power-up Source determines which source the projector defaults to at startup. If no signal is present, the projector checks the sources in order until a source is found or until power down.
Sources>Monitor Out Enable: Selects the Computer 2/monitor out connector to be a monitor loop through of the incoming Computer 1 signal when checked. When it is unchecked, this connector acts as a VESA input.
System>Rear: reverses the image so you can project from behind a translucent screen.
Auto Ceiling : automatically senses when the projector is inverted and turns the image upside down. This is On by default. When in Ceiling mode, Auto
Keystone is turned off.
Ceiling : turns the image upside down for ceiling-mounted projection.
Auto Power : When Auto Power is checked, the projector automatically goes into the startup state after the projector is powered on. This allows control of ceiling mounted projectors with a wall power switch.
Low Power : Turn this on to lower the light output of the lamp. This also lowers the fan speed, making the projector quieter.
Display Messages : displays status messages (such as “Searching” or
“Mute”) in the lower-left corner of the screen.
34
Settings
Sources
System
Power-up
Source
Audio
Screen Saver Off : prevents your computer from going into Screen Save mode.
Power Save : automatically turns the lamp off after no signals are detected for 20 minutes. After 10 additional minutes with no signal, the projector powers down. If an active signal is received before the projector powers down, the image will be displayed.
Screen Save : automatically blanks the screen with a black color after no signals are detected for a preset number of minutes. The image returns when an active source is detected or a remote or keypad button is pressed. Screen
Save is disabled when Power Save is enabled.
System
Screen Save
35
LitePort
This menu allows you to control the embedded LitePort player in your projector to display JPEGs stored on your USB mass storage device. You can
also control the LitePort player with the remote or keypad. See page 27.
Auto Play : When this box is checked (the default), the projector automatically makes the LitePort player the active source and displays, in Full Screen mode, the first JPEG in the LitePort\AutoPlay folder on the USB drive. If no
AutoPlay folder exists or the AutoPlay folder is empty, then no images will be displayed and Folder View mode is entered. When this box is unchecked, you must manually choose the LitePort source using the remote’s computer button or the source button on the keypad. This will display Folder View
mode. See page 27 for details on selecting images to display using the
remote or keypad.
Play All : When this box is checked, the projector plays all the JPEGs in all the folders on the USB drive, starting with the current folder and continuing in alphanumeric folder order. If it is unchecked, only the JPEGs in the selected folder are displayed, and these JPEGs play on a continuous loop.
Fit to Screen : This causes the image to fill the entire screen. If the image has a different aspect ratio than the screen, the image will fit in width or height, depending upon which is larger. Any empty space will be filled with black.
Auto Advance : This option lets you automatically advance images and determine how long each image is displayed before advancing to the next image. Click the check box to turn it on, then highlight Seconds and use the
Up/Down arrows on the keypad or remote to increase or decrease the display time. When playing images with this option, you can go back to the previous slide by pressing the Up arrow or ahead to the next slide quicker by pressing the Down arrow. Press the Select button to stop Auto Advance and return to File View mode.
Slide Transition : This allows you to customize your presentation with slide transitions. Select among None (no transition), Random, Wipe Up, Wipe
Down, Wipe Left, Wipe Right, Split Horizontal In, Split Horizontal Out,
Split Vertical In, Split Vertical Out, Horizontal Blinds, Vertical Blinds, Box
In, and Box Out. For a demonstration of these transitions, go to the Slide
Show>Slide Transition menu in PowerPoint.
36
Slide Transition
LitePort
Auto Advance
Startup Logo: allows you to display a blank Black, White, or Blue screen instead of the default screen at startup and when no source is detected.
Blank Screen : determines what color is displayed when you press the
Blank button on the remote.
Startup Logo
Blank Screen
37
Effect Key : allows you to assign a different function to the Effect button on the remote to quickly and easily use the effect. Only one effect can be enabled at a time. Highlight an effect and press Select to choose a different one. The default effect is About.
Blank : shows an empty screen.
Mute : turns off all sound.
Aspect Ratio: sets the ratio of the image width to image height.
Source: cycles through the available sources.
Auto Image: causes computer sources to be reacquired.
Freeze: pauses the projected image.
About: displays the About menu.
LitePort Rotate: rotates an image clockwise that is displayed with
LitePort.
Language : allows you to select a language for the onscreen display of menus and messages.
Service : to use these features, highlight them and press Select.
Factory Reset : restores all settings (except Lamp Hours) to their default after displaying a confirmation dialog box.
Lamp Reset : resets the lamp hours counter in the About menu to zero. Do this only after changing the lamp. It displays a confirmation dialog box.
Service Code : only used by authorized service personnel.
Language
Effect Key
Service
38
Maintenance
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you don’t intend to use the projector immediately, replace the lens cap.
Using the security lock
The projector has a security lock for use with a cable lock system. See
“Accessories” on page 43 for ordering information. Refer to the information
that came with the lock for instructions on how to use it.
clean the lens with a soft dry cloth and non-abrasive cleaner security lock
39
Replacing the projection lamp
The lamp hour timer in the About menu counts the number of hours the lamp has been in use. Fifty hours before the specified end of the lamp’s life, the message “Replace lamp” briefly appears on the screen at each startup and in the Interactive Display. After 50 additional hours, the lamp will no longer light. You can order new lamp modules from your dealer. See
“Accessories” on page 43 for information.
1 Turn off the projector and unplug the power cable.
2 Wait 60 minutes to allow the projector to cool thoroughly.
3 Turn the projector upside down and remove the lamp door by placing a flat-blade screwdriver into the space between the lamp door and the projector and gently prying the door off.
pry the lamp door off
About menu turn off and unplug the projector wait 60 minutes
4 Loosen the captive screw on the lamp module.
WARNINGS :
• To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.
• Unplug the power cord before replacing the lamp.
• Do not drop the lamp module. The glass may shatter and cause injury.
• Do not touch the glass lamp screen. Fingerprints can obscure projection sharpness.
40 loosen the screw on lamp module
• Be extremely careful when removing the lamp housing. In the unlikely event that the lamp ruptures, small glass fragments may be generated.
The lamp module is designed to contain most of these fragments, but use caution when removing it. Before replacing a ruptured lamp, clean the lamp compartment and dispose of cleaning materials. Wash hands after lamp replacement. This product has a lamp which contains a very small amount of mercury. Dispose of it as required by local, state or federal ordinances and regulations. For more information see www.eiae.org
.
5 Detach the lamp connector from the projector by gently pulling the connector until it is disconnected from the projector.
6 Carefully remove the lamp module by grasping and lifting the metal bail wire. Dispose of the lamp in an environmentally proper manner.
7 Install the new lamp module, making sure that it is properly seated. Be careful not to touch the interior components of the projector.
8 Snap the bail wire back into its flat position against the lamp module.
9 Re-attach the lamp connector to the projector. Make sure the connector is fully inserted.
10 Tighten the screw on the lamp module.
11 Replace the lamp door.
12 Plug in the power cable then press the Power button to turn the projector back on, then reset the lamp hour timer.
Resetting the lamp timer
If the lamp timer has reached the maximum number of hours for the projector lamp, the LED on the projector’s keypad will show a lamp error (see
“LED behavior and meaning” on page 16). To reset the lamp timer, press the
decrease volume button on the keypad and the increase volume button simultaneously for 10 seconds. You can also navigate to the Settings>Ser- vice menu and select Lamp Reset to reset the lamp timer.
41 disconnect lamp connector remove module using bail wire reset lamp time in Service menu
Cleaning the lamp filter screens
In dirty or dusty environments, the dust filter screens on the lamp module and lamp door and in the lamp compartment can become clogged, causing high temperatures inside the lamp module. These high temperatures can impact lamp performance and operating life. Routine maintenance to remove dust and dirt from the screens lowers the lamp operating temperature and prolongs lamp life. To maximize lamp life you will need to clean the screens every 250 hours. Lamp screen maintenance may need to occur more often than 250 hours depending on your installation/use environment.
1
Remove the lamp module. Refer to page 40 for instructions.
2 Examine the dust filter screens on each side of the lamp module. If necessary, use compressed or canned air to clean the screens. Then use a cotton swab dipped in isopropyl alcohol to lightly wipe each screen.
After you've wiped each screen, blow away any remaining contaminants.
3 Before you replace the lamp, repeat the cleaning process on the screen in the lamp compartment in the projector.
4 Examine the dust filter screen on the lamp door. If necessary, use compressed or canned air to clean the screen.
5 Replace the lamp module and lamp door.
screen
42 screen screen screen
Appendix
Accessories
Standard Accessories
(ship with the projector)
Carry Case
Computer Cable 6 ft (1.8 m)
Video Cable 6 ft (1.8 m)
Audio Cable 6 ft (1.8 m)
Audio Cable Adapter
Power Cable*
Navigator Remote
Projection Lamp Module (included in projector)
Lens Cap
Lens Cap Tether
Quick Setup card
User’s Guide with CD
Safety Card
Color-coded Cable Ties, 3 set
SCART Adapter*
*country-dependent
Part Number
110-0819-xx
SP-DVI-A
210-0176-xx
210-0118-xx
210-0177-xx
516-0052-xx
590-0728-xx
SP-LAMP-019
340-1347-xx
321-0192-xx
009-0911-xx
010-0549-xx
009-0659-xx
SP-CABLETIES
301130
NOTE : Use only approved accessories.
43
Optional Accessories
Shipping Case (ATA approved)
Projector Mount
False Ceiling Plate for Projector Mount
Extension Arm for Projector Mount
26” - 47”
Organizer Carry Case
DVI-D Cable 6 ft (1.8 m)
M1 to Component Adaptor
LiteShow Wireless Connection
Audio/Video Cable, 30 ft (9m)
Projector Cable Lock System
50” Diagonal Screen (portable)
60” Diagonal Screen (portable)
Part Number
CA-ATA-020
SP-CEIL-011
SP-LTMT-PLT
SP-LTMT-EXTP
CA-C230
SP-DVI-D
SP-M1-ADPT
LP-LITESHOW
SP-AV30
SP-LOCK-B
A650
HW-DLXSCRN
84” Diagonal Wall/Ceiling Mounted Screen HW-WALLSCR84
Replacement Lamp Module SP-LAMP-019
RF Presenter Remote Control
IR Presenter Remote Control
IR Conductor + Remote Control
HW-PRESENTER-RF
HW-PRESENTER
HW-CONDUCTOR+
Red LED behavior and projector errors
If the projector is not functioning properly and the red LED is blinking, consult Table 4 to determine a possible cause. There are two second pauses between the blinking cycles. Visit our website for more details on the red
LED error codes. See the inside back cover for contact information.
Projected image size
Table 5:
Image sizes
Red LED Behavior
One (1) blink
Two (2) blinks
Three (3) blinks
Four (4) blinks
Five (5) blinks
Table 4:
Explanation
The lamp won't strike after five (5) attempts. Check the lamp and lamp door installations for loose connections.
The lamp counter hours have exceeded lamp life hours. Replace the lamp and reset the lamp hours counter.
The projector has shut down the lamp.
Replace the lamp. Contact Technical Support for repair if replacing the lamp does not solve the problem.
The fan has failed. Contact Technical Support for repair.
The projector is overheating. Check for a blocked air vent. Contact Technical Support for repair if clearing the air vents does not solve the problem.
Distance to screen
(feet/m)
5/1.5
10/3
15/4.6
20/6.1
30/9.1
32.8/10
Minimum
Diagonal
(feet/m)
2.75/0.83
5.5/1.65
8.25/2.53
11/3.36
16.5/5.01
18.0/5.5
Maximum
Diagonal
(feet/m)
3.4/1.02
6.8/2.04
10.2/3.13
13.6/4.15
20.4/6.19
22.3/6.8
Minimum
Horizontal
(feet/m)
2.2/0.66
4.41/1.32
6.61/2.03
8.81/2.69
13.22/4.01
14.45/4.41
Maximum
Horizontal
(feet/m)
2.73/0.82
5.46/1.64
8.2/2.51
10.93/3.33
16.39/4.97
17.92/5.46
NOTE : Visit our website for an interactive image size calculator.
44
INDEX
Numerics
A
advancing PowerPoint slides with LitePort 27
B
blinking green 16 blinking red 16
45
C cables
cleaning the lamp filter screens 42
computer connections
computer image
connecting
customer service contact information 24
D
displaying
displaying JPEG images with LitePort player 27
E
F
first time use
46
I image
image not sharp 21 image not square 21
K
L lamp
laptop
LED
LitePort
player 6, 8, 27, 36 player modes 27
Rotate effect key 38 rotating images 38
M
N
O
only startup screen appears 17
47
P
PowerPoint, advancing slides 7
projector
R
remote control 26 advancing slides 26
S
shutting down the projector 16
T
48
U
V
video connections
W
X
Z
Limited Warranty
Subject to the Limitations, Exclusions and Disclaimers hereof, InFocus Corporation (“InFocus”) warrants that the Projector, Lamps and Accessories
(hereinafter collectively or individually referred to as “Product” as appropriate) purchased from InFocus, an InFocus distributor, or an InFocus reseller will conform to InFocus’ specifications and be free from defects in material or workmanship for the respective Limited Warranty period provided below. InFocus does not warrant that the Product will meet the specific requirements of the end-user customer.
If the Product while subject to this Limited Warranty, is defective in material or workmanship during the warranty period, then InFocus, at its option, will REPAIR or REPLACE the Product.
All exchanged parts and Products replaced under this Limited Warranty will become property of InFocus. InFocus' sole obligation is to supply (or pay for) all labor necessary to repair the Product found to be defective within the Limited Warranty period and to repair or replace defective parts with new parts or, at the option of InFocus, serviceable used parts that are equivalent or superior to new parts performance. Limited Warranty periods are as follows:
• Projector Product Limited Warranty Period (Excluding Lamps) :
Two (2) years from date of purchase.
• Lamp Product Limited Warranty Periods: From the date of Projector
Product purchase, the original installed lamp shall have a 90-day or 500 hours usage Limited Warranty Period, whichever comes first.
Replacement Lamps purchased at the time of Projector Product purchase will have a 90-day or 500 hours usage Limited Warranty Period from the date of installation, whichever comes first.
Replacement lamps purchased after the time of Projector Product purchase shall have a 90-day or 500 hours usage Limited Warranty Period from the date of replacement lamp purchase, whichever comes first.
• Accessory Product Limited Warranty Period: one (1) year from date of purchase.
WARRANTY LIMITATION AND EXCLUSION
THIS WARRANTY SETS FORTH INFOCUS’ MAXIMUM LIABILITY FOR
ITS PRODUCT. THIS WARRANTY EXTENDS ONLY TO PRODUCTS PUR-
CHASED FROM INFOCUS OR AN INFOCUS AUTHORIZED RESELLER.
InFocus shall have no further obligation under the foregoing Limited Warranty if the Product has been damaged due to abuse, misuse, neglect, smoke exposure (cigarette or otherwise), accident, unusual physical or electrical stress, unauthorized modifications (including use of an unauthorized mount), tampering, alterations, or service other than by InFocus or its authorized agents, causes other than from ordinary use or failure to properly use the Product in the application for which said Product was intended.
This Limited Warranty excludes Product cleaning, repair, or replacement of plastics due to cosmetic damage and damage as a result of normal wear.
Product repair outside of the terms of the Limited Warranty will be on a time and materials basis. Prolonged Product “demonstration” causes unusual Product wear and is not considered normal use under the terms of this Limited Warranty.
The Accessory Product Limited Warranty covers the accessory item only and excludes normal wear. The Lamp Product Limited Warranty excludes expected lamp degradation.
Remanufactured Products and Software Products are exempt from the foregoing Limited Warranty. Please refer to the appropriate Remanufactured
Product Limited Warranty or Software Product Limited Warranty for applicable Warranty information.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLI-
CABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WAR-
RANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR
PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT
EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND
THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED
OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFOCUS.
SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS
MAY NOT APPLY TO YOU.
49
Limited Warranty Period
The Limited Warranty periods hereof commence on the date of purchase by the end-user customer. These Limited Warranty provisions shall apply only to the end-user purchaser (first person or entity that purchased a new Product for personal or business use and not for the purpose of distribution or resale). SOME JURISDICTIONS MAY GRANT YOU CONSUMER RIGHTS
WITH MINIMUM WARRANTY DURATION THAT DIFFER FROM THE
DURATIONS PROVIDED HEREIN, AND INFOCUS WILL HONOR ALL
SUCH CONSUMER RIGHTS.
To Be Eligible For Limited Warranty Coverage
Any person exercising a claim under this Limited Warranty must establish to the satisfaction of InFocus both the date of purchase and that the Product was purchased new. The sales receipt or invoice, showing the date of purchase of the Product is the proof of the date of purchase.
To Obtain Warranty Service
During the Limited Warranty period, to exercise this Limited Warranty, the purchaser must first contact 1) InFocus, 2) a service facility authorized by
InFocus or 3) the place of original purchase. InFocus Customer Service –
1-503-685-8888 or visit www.infocus.com/service
For Warranty service, the purchaser will be advised to return or deliver the defective Product freight and all fees prepaid, to an InFocus Service Center or to a service facility authorized by InFocus. When returning Product to
InFocus, a Service Request Number (SR #) is required and must be clearly displayed on the outside of the shipping carton or a similar package affording an equal degree of protection. InFocus or the service facility authorized by InFocus will return the repaired/replaced Product freight prepaid to the purchaser.
Products returned for Warranty service must be accompanied by a written letter that: (i) explains the problem; (ii) provides proof of date of purchase;
(iii) provides the dealer’s name; and (iv) provides the model and serial number of the Product. Upon request of InFocus Corporation or an authorized repair center for InFocus, proof of legal import must accompany the warranty repair Product, otherwise the Product must be returned to the place of original purchase, to the manufacturer (Purchaser must bear all tax, duty and freight), or the Purchaser must bear charges for the warranty repair.
50
No repair or replacement of Product or part thereof shall extend the Limited
Warranty period as to the entire Product. Warranty on the repair part and workmanship shall only be effective for a period of ninety (90) days following the repair or replacement of that part or the remaining period of the
Product Limited Warranty whichever is greater.
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT INFOCUS’ LIABILITY
WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, IN
NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF
THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND
UNDER NO CIRCUMSTANCES SHALL INFOCUS BE LIABLE FOR SPE-
CIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR
LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE PRICE
STATED FOR THE PRODUCTS IS A CONSIDERATION IN LIMITING
INFOCUS’ LIABILITY.
Limitation on Bringing Action - No action, regardless of form, arising out of the agreement to purchase the Product may be brought by purchaser more than one year after the cause of action has accrued.
Governing Law - Any action, regardless of form, arising out of the agreement to purchase the Product is governed by Oregon law.
Mandatory Arbitration – Any action, regardless of form, arising out of the agreement to purchase the Product is subject to mandatory arbitration.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITA-
TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS
LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND
YOU MAY ALSO HAVE OTHER RIGHTS, DEPENDING ON JURISDIC-
TION.
C170_UG.QXD 7/14/04 3:59 PM Page 1
InFocus Corporation
27700B SW Parkway Avenue
Wilsonville, Oregon 97070-9215
1-800-294-6400 • 503-685-8888
Fax: 503-685-8887 http://www.infocus.com
In Europe:
InFocus International B.V.
Strawinskylaan 585
1077 XX Amsterdam,The Netherlands
Phone: +31 20 579 2000
Fax: +31 20 579 2999
In Asia:
InFocus Systems Asia Pte Ltd.
238A Thomson Road
#18-01/04 Novena Square
Singapore 307684
Telephone: (65) 6334-9005
Fax: (65) 6333-4525
> > > > > > >
User’s
Guide
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project