Code Alarm CA6552 Vehicle security, remote start and keyless entry system Installation guide

PDF

Dokuments

Reklāma

PROFESSIONAL

SERIES

Security and Remote Start Installation Guide for models:

Before You Begin ...................................................................................... 4

Wire Connection Guide ........................................................................... 5

4 Pin Main Harness ................................................................................... 7

6 Pin Start Harness ................................................................................... 8

6 Pin Output Harness ............................................................................. 10

8 Pin Input Harness ................................................................................. 11

4 Pin Alternate Output Harness ............................................................. 14

4 Pin AUX Output Harness ..................................................................... 15

3 Pin Door Lock Output Harness ........................................................... 16

Additional Ports ...................................................................................... 20

Antenna / LED / Programming Port ....................................................... 20

DBI Port .................................................................................................... 20

Telematic Interface Port .......................................................................... 20

Set Up & Programming .......................................................................... 21

Transmitter Programming ........................................................................ 21

Manual Feature Programming ................................................................. 21

Programming Feature Banks .................................................................. 22

Tach Programming .................................................................................. 25

Smart Tachless Mode ............................................................................. 24

Adjusting the Shock Sensor .................................................................. 26

Testing the Shock Sensor ...................................................................... 26

Chirp Delete - User Accessible .............................................................. 26

Feature Descriptions ............................................................................. 27

Transmitter Button Functions ............................................................. 34

Security Trigger Zones ......................................................................... 36

Remote Start Shutdown Diagnostics ................................................ 36

BEFORE YOU BEGIN

PROFESSIONAL INSTALLATION

STRONGLY RECOMMENDED

Installation Precautions:

Roll down window to avoid locking keys in vehicle during installation

Avoid mounting components or routing wires near hot surfaces

Avoid mounting components or routing wires near moving parts

Tape or loom wires under hood for protection and appearance

Use grommets when routing wires through metal surfaces

Use a Digital Multi Meter for testing and verifying circuits. DO NOT USE A TEST LIGHT, OR

"COMPUTER SAFE PROBE" as these can set off air bags or damage vehicle computers.

Technical Support

(800) 421-3209 or go to http://techservices.codesystems.com

4 Pin Main Harness

WHITE/RED

WHITE

BLACK

BROWN

PARKING LIGHT INPUT

PARKING LIGHT OUTPUT

GROUND

SIREN OUTPUT ( + )

6 Pin Start Harness

PURPLE

RED

ORANGE

PINK/WHITE

RED/WHITE

PINK

STARTER OUTPUT - MOTOR SIDE

BATTERY 12V ( + )

ACCESSORY 1 ( + )

IGNITION 2 ( + )

BATTERY 12V ( + )

IGNITION 1 ( + )

6 Pin Output Harness

BROWN/BLACK

BLUE/BLACK

VIOLET/BLACK

RED/WHITE

LT GREEN/BLACK

ORANGE

HORN OUTPUT ( - )

IGNITION 3 ( - )

AUX 1 OUTPUT ( - )

TRUNK RELEASE OUTPUT ( - )

FACTORY DISARM / PULSE BEFORE START ( - )

8 Pin Input Harness

4 Pin Alternate Output Harness

BLACK/YELLOW

GREEN/WHITE

LT BLUE

LT GREEN/BLACK

PULSE DURING CRANK ( - )

PULSE AFTER SHUTDOWN ( - )

FACTORY ARM / PULSE AFTER START ( - )

FACTORY DISARM / PULSE BEFORE START ( - )

4 Pin AUX Output Harness

PINK/BLACK

ORANGE/BLACK

GRAY/BLACK

WHITE/BLACK

AUX 5 OUTPUT ( - )

AUX 4 OUTPUT ( - )

AUX 3 OUTPUT ( - )

AUX 2 OUTPUT ( - )

3 Pin Lock Output Harness

BLUE

OPEN

GREEN

UNLOCK ( - )

4 Pin Main Harness

WHITE/RED PARKING LIGHT INPUT

2 WHITE PARKING LIGHT OUTPUT

Locate the parking light output wire at the vehicle’s light switch.

Verification: This wire registers positive voltage when the parking lights are turned on.

Positive switching Parking Lights:

Connect the WHITE/RED wire to a 15 Amp max fused battery source.

Connect the WHITE wire to the parking light output wire.

Negative switching Parking Lights:

Connect the WHITE/RED wire to a good chassis ground.

Connect the WHITE wire to the parking light output wire.

3 BLACK GROUND

Connect the BLACK wire to a solid chassis ground point using a ring terminal and self tapping screw (not supplied). Scrape away paint from the grounding point to ensure a good connection. The recommended grounding point is a metal surface in the driver’s side kick panel area.

NOTE: Do not ground the BLACK wire with any other vehicle components.

4 BROWN SIREN OUTPUT ( + )

Locate a suitable mounting location in the engine compartment for the siren, away from moving parts.

With the bell of the siren aiming downwards, secure the siren in place using self tapping screws, being careful not do drill into any hoses, wiring or components.

Connect the BLACK siren wire to a chassis ground using a ring terminal and self tapping screw (not supplied).

Route the BROWN siren output wire from the control module through the firewall and connect to the RED wire on the siren.

NOTE: Be sure to loom the siren wires, and seal the grommet.

6 Pin Start Harness

PURPLE STARTER OUTPUT ( + )

Locate the vehicle starter wire.

Verification: This wire registers voltage only when the key is turned to the

START position. Cut the vehicle's starter wire in half when installing the starter kill relay.

Verification after starter wire is cut:

KEY SIDE of starter wire registers voltage when the key is turned to the

START position.

MOTOR SIDE of starter wire registers no voltage.

Connect the PURPLE wire to the vehicle starter wire, use the MOTOR SIDE of the vehicle starter wire when installing the starter kill relay.

2 RED BATTERY 12V ( + )

Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.

Verification: This wire will register ( + ) voltage in all positions of the ignition switch.

Connect the RED wire to the constant 12 Volt battery wire.

NOTE: Remove all fuses until all connections are made.

3 ORANGE ACCESSORY 1 ( + )

Locate the vehicle’s accessory wire at the ignition switch.

Verification: This wire registers voltage when the key is turned to ACC

(Accessory) and the ON (or RUN) position. The voltage drops out when the key is turned to the START (or CRANK) position.

Connect the ORANGE wire to the vehicle’s accessory wire.

4 PINK/WHITE IGNITION 2 ( + )

Locate the vehicle’s 2nd ignition wire at the ignition switch (if equipped).

Verification: This wire registers voltage when the key is turned to the ON (or

RUN) position, but not the ACC (Accessory) position. The voltage does not drop out when the key is turned to the START (or CRANK) position.

Connect the PINK/WHITE wire to the vehicle’s ignition 2 wire.

Programmable output: IGN, ACC, Start.

5 RED/WHITE BATTERY 12V ( + )

Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.

Verification: This wire will register ( + ) voltage in all positions of the ignition switch.

Connect the RED/WHITE wire to the constant 12 Volt battery wire.

NOTE: Remove all fuses until all connections are made.

6 PINK IGNITION 1 ( + )

Locate the vehicle’s ignition wire at the ignition switch.

Verification: This wire registers voltage when the key is turned to the ON (or

RUN) position. The voltage does not drop out when the key is turned to the

START (or CRANK) position.

Connect the PINK wire to the vehicle’s Ignition wire.

This wire is also used for Ignition 1 Output.

6 Pin Output Harness

BROWN/BLACK HORN OUTPUT ( - ) 1

Locate the vehicle’s horn wire.

Verification: This wire will register at positive voltage and register ground when the horn switch is pressed.

Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low current output, 200mA.

2 BLUE/BLACK IGNITION 3 / ACTIVE OUTPUT ( - )

The Active Output/Ignition 3 output wire provides a ground output when the remote start function is activated and remains until 4 seconds after the remote start is shutdown. The Ignition 3 output wire can be used for several functions listed below. If this wire will be used for multiple application's a 1 amp diode is required in-line with the stripe facing the control module.

Factory transponder (coded key) bypass.

General Motors VATS bypass, see the following diagram. Use an SPDT relay (not supplied).

Ignition 3 output, see the following diagram. Use an SPDT relay (not supplied).

Accessory 2/3 output, see the following diagram. Use an SPDT relay (not supplied).

GM VATS

Ignition Switch

Fused +12 Volt

Battery Source

87a

Matching Value

Resistor

BLUE/BLACK ActiveOutput

Wire

Ignition 3

X CUT

VATS Control Module

Accessory 2/3

Fused +12 Volt

Battery Source

Fused +12 Volt

Battery Source

Jump To PINK

Ignition Output

Wire From

Control Module

87a

BLUE/BLACK Active Output

Wire

To Vehicle's 2nd or

3rd Ignition Wire

Jump To ORANGE

Accessory Output

Wire From

Control Module

87a

BLUE/BLACK Active Output

Wire

To Vehicle's 2nd or 3rd

3 VIOLET/BLACK AUX 1

This wire provides a ( - ) 200mA output capable of driving relays. For Control of optional accessories (i.e. Power Window/Sunroof, etc.).

To activate refer to the transmitter button configuration chart. Please refer to the selectable options for timing.

4 RED/WHITE TRUNK RELEASE OUTPUT ( - )

Locate the vehicle’s trunk release wire at the trunk release switch.

Verification: This wire will register either positive voltage or ground when the trunk release is activated.

This is a low current 200mA output and in configurable in option programming.

5 LT GREEN/BLACK FACTORY DISARM /

PULSE BEFORE START ( - )

This wire will supply a ( - ) 200mA pulse both upon disarming the system and when the remote start feature is activated. Locate the factory perimeter alarm disarm wire from the key cylinder inside the drivers door.

Verification: This wire registers ground if the key is turned to the unlock position in the driver’s door cylinder.

Connect the LIGHT GREEN/BLACK wire to the factory alarm disarm wire.

6 ORANGE GROUND WHEN ARMED OUTPUT ( - )

This wire will have a continuous ( - ) 200mA output when the system is Armed. This wire is typically used for controlling window modules or additional sensors.

This output can be configured in option programming.

8 Pin Input Harness

1 BLUE/WHITE INSTANT TRIGGER INPUT ( - )

This wire is a GROUND input for an external sensor or secondary pin switch.

Verification: This wire when connected will trigger the security system.

2 GREEN DOOR TRIGGER INPUT ( - )

Locate the vehicle’s dome light or door pin switch wire.

Verification: This wire will register ground (NEG) when the door is opened and the interior light is on. This wire will register positive voltage when the door is closed and the interior light is off.

Connect the GREEN wire to the vehicle’s negative door input wire(s).

NOTE: Certain vehicles may require multiple connections. Refer to vehicle application guide.

3 PURPLE DOOR TRIGGER INPUT ( + )

Locate the vehicle’s dome light or door pin switch wire.

Verification: This wire will register positive voltage (POS) when the door is opened and the interior light is on. This wire will register ground or "0" Volts when the door is closed and the interior light is off.

Connect the PURPLE wire to the vehicle’s positive door input wire(s).

NOTE: Certain vehicles may require multiple connections. Refer to vehicle application guide.

4 WHITE/BLUE EXTERNAL START INPUT ( - )

This wire will activate the Remote Start function when a GROUND pulse is applied to it from an external device.

5 GRAY HOOD PIN INPUT ( - )

Install a Hood Pin Switch and connect to the GRAY wire. This connection is required for Remote Start.

Verification: This wire when connected will register ground when the vehicle's hood is opened.

Connect the GRAY wire to the hood pin.

NOTE: Be sure to loom the wire, and seal the grommet.

6 BLACK/WHITE NEUTRAL SAFETY INPUT ( - )

Locate the vehicle’s neutral safety circuit.

Verification: This wire registers ( - ) voltage when the vehicle’s gear selector is in park or neutral.

Connect the BLACK/WHITE neutral safety input wire to the neutral safety wire of the vehicle or an optional toggle switch. The remote start feature will not operate unless this input is supplied with a ground source.

7 BROWN/RED BRAKE INPUT ( + )

Locate the vehicle’s brake light wire at the brake pedal mounted switch. This connection is required for remote start.

Verification: This wire registers positive voltage when the brake pedal is pressed.

Connect the BROWN/RED wire to the vehicle’s brake light wire.

8 PURPLE/WHITE TACH INPUT

Locate the vehicle’s ignition coil or fuel injector in the engine compartment.

Verification: Test using the following procedure:

Set voltmeter to AC VOLTS.

Attach positive lead of a volt meter to a constant 12 volt source.

Attach negative lead of a volt meter to the wire to be tested.

Start the engine.

Have someone press on the gas pedal slightly as you monitor the meter. If connected to the correct wire, the voltage reading will increase as the engine’s RPM increases.

Connect the PURPLE/WHITE wire to the negative side of the vehicle ignition coil or fuel injector.

4 Pin Alternate Output Harness

1 LT GREEN/BLACK FACTORY DISARM /

PULSE BEFORE START ( - )

Verification: This wire registers ground if the key is turned to the unlock position in the driver’s door cylinder.

This output can be configured in option programming.

2 LT BLUE FACTORY ARM /

PULSE AFTER START ( - )

This wire will supply a ( - ) 200mA pulse both upon arming the system and upon successful completion of the remote start activation sequence and is typically used to re-lock the vehicle’s doors upon remote start if necessary.

This output can be configured in option programming.

3 GREEN/WHITE PULSE AFTER SHUTDOWN ( - )

This wire will supply a ( - ) 200mA pulse after the remote start shuts down. This is typically used to re-lock the vehicle’s doors if they unlock upon remote start shutdown. It can also be used to pulse a door pin-switch wire to prevent the vehicle’s accessories from remaining on after remote start shutdown.

This output can be configured in option programming.

4 BLACK/YELLOW PULSE DURING CRANK ( - )

Locate the vehicle’s second starter (crank) wire at the ignition switch. (if equipped)

Verification: This wire registers voltage only in the start (crank) position of the ignition switch.

This output can be configured in option programming.

4 Pin AUX Output Harness

1 PINK/BLACK AUX 5

This wire provides a ( - ) 200mA output capable of driving relays. For Control of optional accessories (i.e. Power Window/Sunroof, etc.).

To activate refer to the transmitter button configuration chart. Please refer to the selectable options for timing.

2 ORANGE/BLACK AUX 4

This wire provides a ( - ) 200mA output capable of driving relays. For Control of optional accessories (i.e. Power Window/Sunroof, etc.).

To activate refer to the transmitter button configuration chart. Please refer to the selectable options for timing.

3 GRAY/BLACK AUX 3

This wire provides a ( - ) 200mA output capable of driving relays. For Control of optional accessories (i.e. Power Window/Sunroof, etc.).

To activate refer to the transmitter button configuration chart. Please refer to the selectable options for timing.

4 WHITE/BLACK AUX 2

This wire provides a ( - ) 200mA output capable of driving relays. For Control of optional accessories (i.e. Power Window/Sunroof, etc.).

To activate refer to the transmitter button configuration chart. Please refer to the selectable options for timing.

3 Pin Lock Output Harness

1 BLUE

3 GREEN

UNLOCK ( - )

LOCK ( - )

The door lock / unlock outputs are designed to control several different types of systems which may require additional parts. Please review the wire and location chart to see which type of door lock system is in your vehicle. The most common types are shown in the following diagrams.

Negative Switching Locks

All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.

Verification: These wires will register ground when the Lock and Unlock switches are activated.

Connect the GREEN and BLUE wires shown in the diagram below.

Negative Locks:

GREEN (-) Lock Output

Lock

Unlock

Vehicle Door Lock

Control Relays

Positive Switching Locks

All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.

Verification: These wires will register positive voltage when the Lock and

Unlock switches are activated.

Connect the GREEN and BLUE wires shown in the diagram below.

Positive Locks:

Fused +12 Volt

Battery Souce

87a

GREEN (-) Lock Output

Lock

Unlock

Vehicle Door Lock

Control Relays

Fused +12 Volt

Battery Souce

87a

85 BLUE (-) Unlock Output

Reverse Polarity Locks (5-Wire Door locks)

All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.

Verification: These wires will rest at ground and register positive voltage when the Lock and Unlock switches are activated.

Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPDT relays (not supplied).

Reverse Polarity Locks:

Fused +12 Volt

Battery Souce

Lock

87a

Cut

GREEN (-) Lock Output

To Door Lock Motor

Unlock

Fused +12 Volt

Battery Souce

87a

Cut

To Door Lock Motor

Negative Multiplexed Locks

All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.

Verification: This wire will show variable ground when the switch is activated.

Please consult the wire and location chart for specific resistor values for your vehicle.

Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPDT relays (not supplied).

Multiplex Locks:

GREEN (-) Lock Output

Lock

Unlock

87a

Ground

Fused +12 Volt

Battery Source

Resistor

87a

BLUE (-) Unlock Output

Vehicle Door Lock

Control Relays

Positive Multiplexed Locks

All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.

Verification: This wire will show variable positive voltage when the switch is activated. Please consult the wire and location chart for specific resistor values for your vehicle.

Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPDT relays (not supplied).

Multiplex Locks:

GREEN (-) Lock Output

Lock

Unlock

87a

Fused +12 Volt

Battery Source

Resistor

87a

BLUE (-) Unlock Output

Vehicle Door Lock

Adding Aftermarket Actuators

After installing aftermarket actuators, (not supplied). Connect the GREEN and

BLUE wires shown in the diagram below using (2) SPDT relays (not supplied).

Door Lock

Actuator

87a

Fused +12 Volt

Battery Source

Chassis

Ground

GREEN (-) Lock Output

87a

Fused +12 Volt

Battery Source

Chassis

Ground

Additional Ports

Antenna / LED / Programming Port

Mount the supplied antenna/receiver to a clear spot on the vehicle's windshield that will not block the driver's vision. A good location is usually high on the windshield near the rear view mirror. Be careful not to mount the antenna/receiver on any metallic window film, as this will effect system range. Route the antenna/ receiver cable to the control module and plug into the antenna port.

Data Bus Interface Port

This 4 pin port is used for Flashlogic Door Lock and Transponder Databus

Interfaces to communicate with the vehicle's Databus. When using the DBI port to control the Flashlogic Door Lock and Transponder Interface modules the following options may be available. Please refer to the D2D (Data to Data) function list available per vehicle on the tech service web site.

Tach Input

Door Trigger

Door Lock Control

Dome Light Supervision

Brake Safety Shut Down

Trunk/Hatch Open

Passlock / Passkey Interface (GM Only)

Transponder Interface Activation

Factory Alarm Arm / Disarm Diesel Glow Plug Input

Manual Arm / Disarm Inputs (factory keyless controls system)

Telematic Interface Port

This 4 pin port is used for telematic Interface accessories, such as the CarLink

ASCL1, which can control some of the following features.

Door Lock Control

Sliding Doors

Car Find

Trunk Release

AUX Output

Set Up & Programming

Transmitter Programming - Feature Bank 1

Turn the ignition ON.

Press and hold the valet/override button.

Within 10 seconds the system will chirp (3) three times.

Press 1 button of each transmitter you wish to program.

The system will respond with 1 chirp for each accepted transmitter.

Pressing the override button at anytime during programming will advance to the next bank.

NOTE: The system will exit transmitter programming after 15 seconds of inactivity.

NOTE: This system has 1 button programming which programs all channels of the system.

NOTE: The system will hold up to 4 transmitters in memory, programming a 5th transmitter will erase the oldest transmitter in memory.

NOTE: This system has PTN - Programmed Transmitter Notification. Each time the ignition is turned ON, the LED will flash the number of transmitters programmed to the system.

Transmitter programming for 2 Car Mode *2 way system only:

Enter the transmitter into 2 Car Mode. (Refer to transmitter operation in the owners manual for 2 car operation)

Follow the steps above for transmitter programming.

NOTE: 2 car mode requires an additional security system installed in a second vehicle.

Manual Feature Programming - Feature Bank 2 - 5

Turn the ignition ON.

Press and hold the valet/override button.

Within 10 seconds the system will chirp (3) three times.

Use the valet/override button to advance through each option bank. For feature programming advance to Feature Bank 2, 3, 4 or 5, which is (4) four, (5) five, (6) six and (7) seven chirps.

Use the transmitter button to scroll through the selections in each feature bank, the system will chirp to match the feature number.

Press the transmitter button to change the desired feature. The LED will flash indicating the changed feature.

Defaulting All Features: Pressing the button anytime while in any of the feature banks will default all features and return you to feature bank 2 - 4 chirps.

NOTE: The system will remain in feature programming mode as long as the ignition is on, there is no time limit. To exit programming turn the IGNITION OFF.

Feature Bank 1 - 3 Chirps

Transmitter Programming

Refer to transmitter programming.

Feature Bank 2 - 4 Chirps

Security Control

1 Silent Choice

2 Passive Locks

3 Passive Arming

4 Siren / Horn - Arm/Disarm Chirps

5 Siren Duration

6 Security

7 Anti-Hijack Mode

8 Orange - Ground w/ Armed Output

1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash

Active

Siren / Horn

OFF

Passive

Siren

30 Seconds 60 Seconds

OFF ON

OFF ON

Ground While

Armed

Ground While

Disarmed

Horn

Feature Bank 3 - 5 Chirps

Output Control

1 Extended Lock Pulse

Factory Disarm

Lt Green / Black

3 Ignition Controlled Locks

Trunk Output Timing

Red / White Output

5 Horn Output Timing

6 Real Panic

AUX 1

Violet / Black Output

AUX 2

White / Black Output

AUX 3

Gray / Black Output

AUX 4

Orange / Black Output

AUX 5

Pink / Black Output

1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash

1 Second 3.5 Seconds

1 Second Lock,

Double Pulse

Unlock

30 Second

Lock, Double

Pulse Unlock

Double Pulse

Lock, 1 Second

Unlock

Factory

Disarm

2nd Unlock

Factory Disarm

/ Start Status

OFF

Lock and

Unlock

Lock Only

1 Second

Pulse

16mS

10 Seconds

10mS

20 Seconds

30mS

Unlock Only

Latched until

IGN ON

40mS

Latched ON until Button

Press

50mS

ON OFF

Push and Hold Latched

Latched until

IGN ON

Latched until

IGN ON

Latched until

IGN ON

Latched until

IGN ON

Latched until

IGN ON

Dome Light

Output

Defrost Output

Single Pulse

After Start

Defrost Output

Latched 5 Min

After Start

10 Second

Pulse with Arm

10 Second

Pulse with

Disarm

10 Second

Pulse with Arm

10 Second

Pulse with

Disarm

10 Second

Pulse with Arm

10 Second

Pulse with

Disarm

10 Second

Pulse with Arm

10 Second

Pulse with

Feature Bank 4 - 6 Chirps

Remote Start Control

1 RF Start Chirp

2 Run Time

3 Running Lights

4 Tach Mode

5 Voltage Level

6 Crank Time

7 Crank Averaging / Crank Time

8 Gas / Diesel

9 Single / Double Press Start

10 IGN 2 Output

11 2 or 3 Hour Start

12 Turbo Timer

13 Transmission Mode

14 Temperature Start

1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash

15 Minutes

Steady

Tach

High

OFF

5 Minutes 10 Minutes 20 Minutes

Flashing

Tachless

(Crank Average

/ Voltage)

Hybrid (Crank

Average / NO

Voltage)

DBI Port

Low

1.5 Seconds 2.0 Seconds 1.0 Seconds 0.8 Seconds

Averaging Preset Time

45 Minutes

4.0 Seconds

60 Minutes

45 Second

Delay

Gas

10 Second

Delay

15 Second

Delay

20 Second

Delay

Double Press Single Press

Ignition 2 Accessory

3 Hour 2 Hour

1 Minute OFF

OFF 14F

Start / Crank

3 Minute

5 Minute

-4F

Feature Bank 5 - 7 Chirps

4 Pin Alternate Output Control

1 Lt Green / Black Output

2 Lt Blue Output

3 Green / White Output

4 Black / Yellow Output

1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash

Pulse Before

Start / During

Unlock

Ground While

Running

Ignition

Pulse After

Start / During

Lock

Ground While

Running

Ignition

Accessory

Pulse During

Crank

Pulse During

Crank

Pulse After

Shutdown

Ground While

Running

Ignition Accessory

Pulse During

Crank

Pulse During

Crank

Ground While

Running

Tach Programming

The unit will not operate unless tach is programmed or tachless option is

turned ON. If an attempt is made to start the vehicle via the remote start without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and stored. If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle is running in certain instances and reengage the starter motor.

The Remote Start unit will learn the tach rate of most vehicle's single coil, multiple coil packs, or single injector. To learn tach:

Turn the ignition key to the ON position.

Press and release the valet/override button 3 times.

Immediately turn the ignition key OFF.

Press and hold the valet/override button, then start the vehicle using the key.

When the unit senses the tach signal, the parking lights will begin to flash.

Allow the vehicle to settle to a normal idle speed.

Release the valet/program push-button switch. The parking lights will turn on for 2 seconds indicating that the learned tach signal is stored and the unit has exited tach learn mode.

NOTE: If the unit fails to learn tach rate due to an improper tach connection or a poor tach source, the parking lights will not flash. To correct this situation, locate and connect the PURPLE/WHITE wire to the proper tach signal, and then repeat the tach learn routine.

Smart Tachless Mode

Smart Tachless Mode is available only if a tach signal has never been learned to the system and when activated will automatically change the Tach Mode feature in option programming to Tachless without the need to enter the feature programming mode.

Activate the remote start. The parking lights should begin flashing 7 times indicating no tach signal has been learned.

Within the 7 flash time period, press and hold the button.

The system will chirp 1 time indicating the system is now in tachless mode.

Adjusting the Shock Sensor

Increase sensitivity by turning the adjustment dial clockwise.

Decrease sensitivity by turning the adjustment dial counter clockwise.

Testing the Shock Sensor

Arm the system and wait 6 seconds for the zone to stabilize, then firmly strike the vehicles bumper.

Chirp Delete - User Accessible

System ARM/DISARM chirps can be toggled ON or OFF without entering the programming feature banks.

Turn the ignition ON then OFF.

Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF.

Dome Light Delay / Theater Dimming

The system can be programed to delay arming after the lock button is pressed (60 second max) for vehicles with a dome light delay or theater dimming feature. Once programed the system will ‘learn’ the timing of the dome light delay and add 2 seconds before arming.

Close all doors with ignition off.

Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK ,

UNLOCK, LOCK. The LED will light solid to indicate the system has entered DOME DELAY LEARN MODE.

Immediately OPEN then CLOSE the door WITHOUT disarming the system. The system will then monitor the door trigger wire. Once the dome light turns off, the system will then add 2 seconds and then exit the learning mode.

The LED will begin to flash indicating the system has exited the learning mode and is now armed.

Feature Descriptions

Feature Bank 2 - Security

1 - Silent Choice: Controls the normal arm/disarm chirps of the security system.

ON - Silent arming/disarming upon first press of lock/unlock, pressing lock/ unlock a second time will activate the arm/disarm chirps respectively. The system will only sound the arm/disarm chirps upon a second press of the lock/unlock buttons.

OFF - normal arm/disarm chirps upon the first press of lock/unlock.

2 - Passive Locks: Determines manual or automatic locking of the vehicle’s doors.

Active - Requires use of the transmitter to lock the vehicle’s doors.

Passive - Automatically locks the vehicle’s doors 1 minute after the last door is closed

3 - Passive Arming: Determines manual or automatic locking of the vehicle’s doors.

Active - Requires use of the transmitter to arm the security system.

Passive - Automatically arms the security system 1 minute after the last door is closed

4 - Siren / Horn: This feature selects which output(s) will sound the system’s arm/disarm chirps. This feature does not effect the triggered state of the security system and during a triggered cycle, both the siren and horn outputs will activate respectively.

5 - Siren Duration: This feature controls the length of time the system will sound when triggered.

6 - Security: Controls security functionality - ON / OFF.

ON - Full security functionality.

OFF - The security system does not trigger. Panic, Remote Start and all other convenience features operate as normal.

7- Anti-Hijack Mode: Controls car jack mode - ON / OFF.

OFF - Standard security system operation.

8 - Ground While Armed / Orange Output: Controls the output of the orange wire. This wire will either supply a ( - ) output when armed OR disarmed.

Feature Bank 3 - Output Control

1 - Extended Lock Pulse: Controls the timing of the BLUE and GREEN lock output wires.

1 Second - Single 1 second lock pulse, single 1 second unlock pulse.

3.5 Seconds - Single 3.5 second lock pulse, single 3.5 second unlock pulse.

1 Second Lock, Double Pulse Unlock - Single 1 second lock pulse, double 1 second unlock pulse.

30 Second Lock, Double Pulse Unlock - Single 30 second lock pulse, double

1 second unlock pulse.

Double Pulse Lock, 1 Second Unlock - Double 1 second lock pulse, single 1 second unlock pulse.

2 - Factory Disarm: Controls the timing of the LT. GREEN/BLACK factory disarm wire on the 6 pin output harness only and does not change the output of the factory disarm wire on the 4 pin alternate output harness.

Factory Disarm - Single 1 second pulse with unlock and remote start activation.

2nd Unlock - Same output as unlock with 2nd press of unlock.

Start Status - Single 1 second pulse with unlock and continuous ( - ) output during the remote start cycle.

3 - Ignition Controlled Locks: Control of door locks when the ignition is cycled

ON or OFF.

OFF - Door locks not activated by ignition.

Lock and Unlock - Doors lock when ignition is turned on and unlock when ignition is turned off.

Lock Only - Doors lock when ignition is turned on.

Unlock Only - Doors unlock when ignition is turned off.

4 - Trunk Output Timing - Red/White Output: Controls the output timing/type of the RED/WHITE output.

1 Second Pulse - 1 second pulse output.

10 Second - Continuous output for 10 seconds.

20 Seconds - Continuous output for 20 seconds.

Latched until IGN ON - Continuous output until the vehicle’s ignition is turned

ON.

Latched ON until Button Press - Continuous output until the activation button is pressed again.

5 - Horn Output Timing: Control the minimum horn pulse time in milli seconds, some vehicle will require a longer pulse to activate the factory horn.

16mS 10mS 30mS 40mS 50mS

6 - Real Panic: Controls the panic out when triggered from the transmitter.

ON - Randomized horn honks when panic is triggered.

OFF - Standard pattern horn honks when panic is triggered.

7 - AUX 1: Controls the VIOLET/BLACK AUX 1 output activation type and timing.

Push and Hold - Output is continuously active until transmitter button is released.

Latched - Output stays active until button is pressed again.

Latched until IGN ON - Output stays active until the ignition is turned on.

Dome Light Output - Output used for illuminated entry and is not controlled by the AUX 1 function of the transmitter.

Defrost Output Single Pulse - Single 1 second pulse after start

Defrost Output Latched 5 Minutes - 5 minute continuous output after remote start.

8 - AUX 2: Controls the WHITE/BLACK AUX 2 output activation type and timing.

Push and Hold - Output is continuously active until transmitter button is released.

Latched - Output stays active until button is pressed again.

Latched until IGN ON - Output stays active until the ignition is turned on.

10 Second Pulse with Arm - Output stays active for 10 seconds with press of lock button.

10 Second Pulse with Disarm - Output stays active for 10 seconds with press of unlock button.

9 - AUX 3: Controls the GRAY/BLACK AUX 3 output activation type and timing.

Push and Hold - Output is continuously active until transmitter button is released.

Latched - Output stays active until button is pressed again.

Latched until IGN ON - Output stays active until the ignition is turned on.

10 Second Pulse with Arm - Output stays active for 10 seconds with press of lock button.

10 Second Pulse with Disarm - Output stays active for 10 seconds with press of unlock button.

10 - AUX 4: Controls the ORANGE/BLACK AUX 4 output activation type and timing.

Push and Hold - Output is continuously active until transmitter button is released.

Latched - Output stays active until button is pressed again.

Latched until IGN ON - Output stays active until the ignition is turned on.

10 Second Pulse with Arm - Output stays active for 10 seconds with press of lock button.

10 Second Pulse with Disarm - Output stays active for 10 seconds with press of unlock button.

11 - AUX 5: Controls the PINK/BLACK AUX 5 output activation type and timing.

Push and Hold - Output is continuously active until transmitter button is released.

Latched - Output stays active until button is pressed again.

Latched until IGN ON - Output stays active until the ignition is turned on.

10 Second Pulse with Arm - Output stays active for 10 seconds with press of lock button.

10 Second Pulse with Disarm - Output stays active for 10 seconds with press of unlock button.

Feature Bank 4 - Remote Start Control

1 - RF Start Chirp: Turns remote start activation confirmation chirps ON or OFF.

2 - Run Time: Controls the time in minutes that the vehicle will stay running under control of the remote start until the system times out. The system may also be shut down at any time by use of the transmitter or system shutdowns.

3 - Running Lights: Controls the WHITE parking light output wire during remote start.

Steady - Parking lights constant during the remote start cycle.

Flashing - Parking lights flash at a slow pace during the remote start cycle.

4 - Tach Mode: Determines how the system monitors the engine running during remote start.

Tach - Hard wired directly to the tach wire of the vehicle to monitor AC voltage.

Tachless (Crank Average/Voltage) - Determines crank time by averaging the last 8 times the vehicle was started with the key and then monitors the change in voltage after remote start.

Hybrid (Crank Average / No Voltage) - Determines crank time by averaging the last 8 times the vehicle was started with the key.

DBI Port - Monitors the vehicle’s tach rate through an interface module connected to the DBI port.

5 - Voltage Level: The voltage variance for remote start when set to tachless.

(see tach mode)

HIGH - The variance in battery voltage from before the remote start is activated to after the engine is running must be greater than 0.5 volts.

LOW - The variance in battery voltage from before the remote start is activated to after the engine is running may be less than 0.5 volts.

6 - Crank Time: Preset output times for the PURPLE starter wire.

7 - Crank Average / Crank Time: The length of time in which the remote start will crank the vehicle’s starter.

Crank Average - Determines crank time by averaging the last 8 times the vehicle was started with the key.

8 - Gas / Diesel: Selects engine type and delay time for the starter output wire during remote start activation.

Gas - Gasoline engine, no delay for the starter output wire.

10 Second Delay - Diesel engine, delays the starter output wire for 10 seconds after the ignition has been powered up by the remote start.

15 Second Delay - Diesel engine, delays the starter output wire for 15 seconds after the ignition has been powered up by the remote start.

20 Second Delay - Diesel engine, delays the starter output wire for 20 seconds after the ignition has been powered up by the remote start.

45 Second Delay - Diesel engine, delays the starter output wire for 45 seconds after the ignition has been powered up by the remote start.

9 - Single / Double Pulse Start: Switches the remote start activation between a single or double press from the transmitter.

10 - IGN 2 Output: Programmable high current output.

Ignition 2 - Output becomes active with the same timing as the ignition output and does not drop out during crank.

Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.

Start / Crank - Output becomes active with the same timing as the starter output wire, during crank only.

11 - 2 or 3 Hour Start: When activated, the remote start will activate and run for the programmed time and shut down every 2 or 3 hours.

12 - Turbo Timer: When activated, the vehicle will run for the programmed time.

OFF 1 Minute 3 Minutes 5 Minutes

13 - Transmission Mode: Not available on this model.

14 - Temperature Start: Sets the threshold temperature for temperature start mode. When temperature start is activated, the remote start function will activate when the ambient temperature drops below the selected temperature.

Feature Bank 5 - 4 Pin Alternate Output Control

1 - Lt Green/Black Output : Controls the LT GREEN/BLACK output activation type and timing.

Pulse before Start / During Unlock - 1 second pulse when remote start is activated. Also a 1 second pulse when unlock is pressed.

Ground While Running - Continuous output for the entire remote start sequence until after the vehicle shuts down.

Ignition - Output becomes active with the same timing as the ignition output and does not drop out during crank.

Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.

Pulse During Crank - Output becomes active with the same timing as the starter output wire, during crank only.

2 - Lt Blue Output : Controls the LT BLUE output activation type and timing.

Pulse After Start / During Lock - 1 second pulse after the remote start sequence and has confirmed the vehicle is running. Also a 1 second pulse when unlock is pressed.

Ground While Running - Continuous output for the entire remote start sequence until after the vehicle shuts down.

Ignition - Output becomes active with the same timing as the ignition output and does not drop out during crank.

Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.

Pulse During Crank - Output becomes active with the same timing as the starter output wire, during crank only.

3 - Green/White Output : Controls the GREEN/WHITE output activation type and timing.

Pulse After Shutdown - 1 second pulse after the remote start has shutdown.

Ground While Running - Continuous output for the entire remote start sequence until after the vehicle shuts down.

Ignition - Output becomes active with the same timing as the ignition output and does not drop out during crank.

Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.

Pulse During Crank - Output becomes active with the same timing as the starter output wire, during crank only.

4 - Black/Yellow Output : Controls the BLACK/YELLOW output activation type and timing.

Pulse During Crank - Output becomes active with the same timing as the starter output wire, during crank only.

Ground While Running - Continuous output for the entire remote start sequence until after the vehicle shuts down.

Ignition - Output becomes active with the same timing as the ignition output and does not drop out during crank.

Accessory - Output becomes active with the same timing as the accessory output, drops out during crank.

Transmitter Button Functions

1 Way

Transmitter

Lock Unlock

Panic

Lock X

Unlock X

2 Step Unlock X

Trunk X

Car Finder

Panic

Remote Start

Shutdown

Run Time

Extention

AUX 1

Shock Bypass

Hidden Alarm

Passive Arming

Bypass

Turbo Timer

2 / 3 Hour Start

Daily Start Timer

Temperature

Start

X X

AUX 2, 3, 4, 5 - Access in AUX Mode

X X Enter AUX Mode

AUX 2

AUX 3

AUX 4

AUX 5

Press and Hold Find + Start

Transmitter LED flashes 1 time

Push and Hold (3 Sec)

Press and Release

Press and Release 2 times

Push and Hold (3 Sec)

Press and Release

Push and Hold (3 Sec)

Press and Release (1 or 2 times depending on selectable option)

Push and Hold (3 Sec)

Press and Release 4 times.

Push and Hold (3 Sec)

Press and Release Lock then

Press Lock + Car Find

Press and Release Car Fnd then

Press Lock

Press and Release

Press Unlock + Start

Ignition ON/OFF, Press and Hold

Valet Button, Press Start 4 times

Press Lock + Start

Remote Start

Shutdown

Run Time

Extention

AUX 1

Shock Bypass

Hidden Alarm

Passive Arming

Bypass

Turbo Timer

2 / 3 Hour Start

Daily Start Timer

Menu

Temperature

Start

2 Way

Transmitter

Lock Unlock

Panic

Lock X

Unlock X

2 Step Unlock X

Trunk

Car Finder

Panic

Enter AUX Mode

AUX 2

AUX 3

AUX 4

AUX 5

Start Function Operation Method

Press and Release

Press and Release 2 times

Push and Hold (3 Sec)

Press and Release

X X

AUX 2, 3, 4, 5 - Access in AUX Mode

Push and Hold (3 Sec)

Press and Release (1 or 2 times depending on selectable option)

Push and Hold (3 Sec)

Press and Release 4 times.

Push and Hold (3 Sec)

Press and Release Lock then

Press Lock + Car Find

Press and Release Car Fnd then

Press Lock

Press and Release

Press Unlock + Start

Ignition ON/OFF, Press and Hold

Valet Button, Press Start 4 times

Press Lock + Start

Press and Hold

Press Unlock + Start While Armed

Press and Hold F for 2 seconds

LCD displays AU

Push and Hold (3 Sec)

Security Trigger Zones

If the security system has been triggered the LED will flash one of the patterns below indicating the zone.

LED FLASHES TRIGGER ZONE

2 Flashes

3 Flashes

4 Flashes

5 Flashes

Hood / Trunk Input

Door Input

Shock Sensor

Ignition Input

Remote Start Shutdown Diagnostics

If the remote start shuts down or fails to start, the parking lights will flash one of the patterns below indicating the shutdown input.

To manually enter diagnostics and view the last shutdown, turn the ignition ON and press and release the button.

LED FLASHES

3 Flashes

4 Flashes

5 Flashes

7 Flashes

SHUTDOWN ZONE

Hood Input

Brake Input

Neutral Safety Input

Remote Start Valet Mode

Manual Transmission Mode not set (manual transmission models only)

BLUE/WHITE

GREEN

PURPLE

WHITE/BLUE

GRAY

BLACK/WHITE

INSTANT TRIGGER INPUT ( - )

DOOR TRIGGER INPUT ( - )

DOOR TRIGGER INPUT ( + )

EXTERNAL START INPUT ( - )

HOOD INPUT ( - )

NEUTRAL SAFETY INPUT ( - )

BROWN/RED BRAKE INPUT ( + )

INPUT

SHOCK SENSOR PORT

TRACKING PORT

ANTENNA

LED

VALET

PURPLE

RED

ORANGE

PINK/WHITE

RED/WHITE

PINK

WHITE/RED

WHITE

BROWN

BLACK

STARTER OUTPUT - MOTOR SIDE ( + )

BATTERY 12V ( + )

ACCESSORY 1 ( + )

IGNITION 2 ( + )

BATTERY 12V ( + )

IGNITION 1 ( + )

PARKING LIGHT INPUT

PARKING LIGHT OUTPUT

GROUND

SIREN OUTPUT ( + )

PINK/BLACK

ORANGE/BLACK

GRAY/BLACK

WHITE/BLACK

BROWN/BLACK

BLUE/BLACK

VIOLET/BLACK

RED/WHITE

LT GREEN/BLACK

ORANGE

BLACK/YELLOW

GREEN/WHITE

LT BLUE

LT GREEN/BLACK

BLUE

OPEN

GREEN

DBI PORT

AUX 5 OUTPUT ( - )

AUX 4 OUTPUT ( - )

AUX 3 OUTPUT ( - )

AUX 2 OUTPUT ( - )

HORN OUTPUT ( - )

IGNITION 3 / ACTIVE OUTPUT ( - )

AUX 1 OUTPUT ( - )

TRUNK RELEASE OUTPUT ( - )

FACTORY DISARM / PULSE BEFORE START ( - )

GROUND WHEN ARMED ( - )

PULSE DURING CRANK ( - )

PULSE AFTER SHUTDOWN ( - )

FACTORY ARM / PULSE AFTER START ( - )

FACTORY DISARM / PULSE BEFORE START ( - )

UNLOCK ( - )

Audiovox Electronics Corporation.

Customer Service 1-800-421-3209

WWW.CODE-ALARM.COM

FCC COMPLIANCE

This device complies with Part 15 of the FCC rules and with RSS-210 of

Industry Canada. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including any interference that may cause undesired operation.

Warning!

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Sveiki! Esmu AI tērzēšanas robots, kas īpaši apmācīts, lai palīdzētu jums ar Code Alarm CA6552 Vehicle security. Esmu rūpīgi pārskatījis dokumentu un varu palīdzēt jums atrast precīzu nepieciešamo informāciju vai izskaidrot saturu skaidri un vienkāršiem vārdiem. Neatkarīgi no tā, vai meklējat norādījumus par konkrētām funkcijām, problēmu novēršanas darbībām vai vispārēju lietošanu, droši uzdodiet savus jautājumus. Jo vairāk informācijas sniegsiet par savām bažām vai vajadzībām, jo precīzāk un efektīvāk es varu jums palīdzēt!

Palīgs raksta

Palīgs nav pie klaviatūras. Lūdzu, mēģiniet vēlreiz vēlāk.

Satura rādītājs

Izskatās, ka esat nonācis pie dokumenta, kas ir rakstīts vairākās valodās, ieskaitot tādu, kas nav jūsu dzimtā valoda. Varat izmantot šīs saites, lai īslaicīgi paslēptu lapas bez vēlamās valodas.

Reklāma

PROFESSIONAL

SERIES

Security and Remote Start Installation Guide for models:

Table of Contents

BEFORE YOU BEGIN

PROFESSIONAL INSTALLATION

STRONGLY RECOMMENDED

Installation Precautions:

Roll down window to avoid locking keys in vehicle during installation

Avoid mounting components or routing wires near hot surfaces

Avoid mounting components or routing wires near moving parts

Tape or loom wires under hood for protection and appearance

Use grommets when routing wires through metal surfaces

Use a Digital Multi Meter for testing and verifying circuits. DO NOT USE A TEST LIGHT, OR

"COMPUTER SAFE PROBE" as these can set off air bags or damage vehicle computers.

Technical Support

(800) 421-3209 or go to http://techservices.codesystems.com

4 Pin Main Harness

6 Pin Start Harness

6 Pin Output Harness

8 Pin Input Harness

4 Pin Alternate Output Harness

4 Pin AUX Output Harness

3 Pin Lock Output Harness

4 Pin Main Harness

6 Pin Start Harness

6 Pin Output Harness

8 Pin Input Harness

4 Pin Alternate Output Harness

4 Pin AUX Output Harness

3 Pin Lock Output Harness

Additional Ports

Set Up & Programming

Transmitter Programming - Feature Bank 1

Manual Feature Programming - Feature Bank 2 - 5

Tach Programming

Smart Tachless Mode

Adjusting the Shock Sensor

Testing the Shock Sensor

Chirp Delete - User Accessible

Dome Light Delay / Theater Dimming

Feature Descriptions

Feature Bank 2 - Security

Feature Bank 3 - Output Control

Feature Bank 4 - Remote Start Control

Feature Bank 5 - 4 Pin Alternate Output Control

Transmitter Button Functions

Security Trigger Zones

Remote Start Shutdown Diagnostics

Audiovox Electronics Corporation.

Customer Service 1-800-421-3209

WWW.CODE-ALARM.COM

Saistītie

CA 650 car security system Installation Instructions

Remote Engine Starter TRX 72 Installation Manual

car alarm CA 650 Installation Instructions

Code Alarm CA 5051 Installation manual

Code Alarm CA6552SST Long range vehicle security, remote start and keyless entry system User Manual

CODE ALARM ca 6552 SST Owner's Guide | AI Chat & PDF

Code Alarm CA 5051 Installation manual

Remote Start Professional CA6150RX Installation Guide

Code Alarm PROFESSIONAL SERIES CA 5150 Installation Guide

Professional Series CA 5051MT Installation Guide

Code Alarm Professional Series CA 5050 Installation manual

CODEALARM PROFESSIONAL SERIES ca 6552 and ca 6552 SST Owner's Guide