BENDIX

24

6

7

14

15

16

17

18

ABS TECH INFO - ARVIN MERITOR

End of Line Testing without TOOLBOX™Software

1. Apply 12 volts DC power to the ABS.

( Using the ABS lamp to check the line.)

2. The ECU/single modulator valve assembly should click two times.

3. If the indicator lamp comes on for three seconds and goes out: This indicates a correct installation. The end of line test is complete. If the ABS indicator lamp comes on and stays on, check the sensor installation:

A. Remove the power from the ABS and raise the sensed wheels so they may be rotated.

B. Repeat Step 1 and Step 2.

C. Rotate each sensed wheel — one at a time — at a rate of 1/2 revolution per second. This rate equals a wheel speed of approximately 4 mph (7 kph). The ABS indicator lamp should now go out and stay out indicating a correct installation. The end of line test is complete.

4. If the ABS lamp does not go out, there is a sensor gap problem or hardware fault. Adjust the sensor and, if necessary, perform a fault code check.

Sensor Gap Adjustment

Push the sensor into its holder until it contacts the tooth wheel. At installation, there must be no gap between the sensor and the tooth wheel. Measure the AC voltage output. The value should be 0.2 volt AC when the wheel is rotated at a rate of 1/2 revolution per second. Perform any necessary repairs. Repeat the sensor installation check.

If the trailer lamp still does not go out, a system fault exists. Perform a fault code check.

Fault Code Check

Use constant power activation to perform the following fault code check.

1. Apply constant power to the ECU/single modulator valve assembly for more than one, but less than five seconds.

2. Remove the power.

3. Reapply the power.

4. Check the trailer ABS indicator lamp on the side of the trailer. The fault code will be displayed three times.

5. Find the fault on the chart and perform the necessary repairs.

6. After performing the necessary repairs, repeat the end of line test to verify correct sensor installation.

Blink Code Chart

(Most common codes - for more info see Meritor Wabco TP-0173 chart)

Blink Code

4

Problem Area Action

Sensor YE1 (curbside sensor) Check sensor installation. Perform necessary repairs.

Sensor YE2 (roadside sensor) Check sensor installation. Perform necessary repairs.

ECU/single modulator valve assembly

Power Supply

Verify correct installation. If code continues, contact

Meritor WABCO for assistance.

Verify correct electrical installation. Check power supply.

Perform necessary repairs.

ECU Failure

SAE J1708 Failure

SAE J2497 Failure

Generic I/O Failure

Verify correct installation. If code continues, contact

Meritor WABCO for assistance.

Internal failure, contact Meritor WABCO.

Internal failure, contact Meritor WABCO.

Verify correct electrical installation. Check power supply.

Perform necessary repairs.

ABS - 2S/1M, 2S/2M MERITOR/WABCO COMPONENT KITS

2 Sensor/1 Modulator Valve

(2S/1M) Configuration Shown

Tandem Suspension,

Two Wheels Sensed

KIT PART NO. 1542014

REPLACEMENT PARTS LIST





KIT PART NO. 1542015

REPLACEMENT PARTS LIST FOR

Qty Part No.

Description

1 S4005001010 ECU

1 S4493260300 10' Power cable

2 S4497130180 6' Sensor Ext cable

1 ---

1 ---

Installation Guide

End of Line Test

Enhanced Easy-Stop™

Qty Part No.

Description

1 S4005001010 ECU

1 PEC4-48 48' Power Ext cable

1 S4493260050 1.6' Power Cable

2 S4497130180 6' Sensor

1 ---

Ext.cable

ABS Label For

1

1

---

---

Lamp

Installation Guide

End of Line Test





KIT PART NO. 1542016


Qty Part No.

Description

1 S4005001010 ECU

1 S4493260300 10' Power cable


1 --Installation Guide

1 --End of Line Test


We have developed these kits for MANUFACTURERS ONLY - OEM ONLY.

These kits are not available to aftermarket distributors -

Those kits are on the following pages. THANK YOU!

2S/1M schematic (showing air)

1011452

SPRING BRAKE CONTROL VALVE

Spring Brake Priority System

Complies with all changes to

FMVSS121.Designed for use with a single reservoir on a typical single or tandem axle trailer application. Part No. 110500

3 /

8

"

Control

3/8"

Delivery

3/8"

Delivery

3 /

8

"

Supply

1 /

2

"

Reservoir

N9508-AA

1010447

6003

110500

A/C

1010447

1010447

1010447

S4005001010

(See page 28)

6006

25

N9508-AA

1011451

A/C = Anti-Compounding

Service Brake

Spring Brake

Supply Line (Red)

Control Line (Blue)

110500 - Spring Brake control valve, R955322 - Wabco ECU valve, 6003 - 3/4" to 1/2" pipe nipple,

6006 - 3/4" pipe nipple, N9508-AA air tank, 1010447 - spring brake chamber,

1011451 - red emergency gladhand, 1011452 blue service gladhand.

26

ABS - 2S/1M COMPONENT PARTS - SPRING BRAKE PRIORITY


Service Brake

Spring Brake

COMPONENTS LISTING:

No. 1 = 110500 - Spring Brake control valve,

No. 2 =S4005001010 - Wabco ECU valve,

No. 4 = 6003 - 3/4" to 1/2" pipe nipple,

No. 5 = 6006 - 3/4" pipe nipple,

No. 6 = N9508-AA air tank,

No. 7 = 1010447 - spring brake chamber,

No. 8 = 1011451 - red emergency gladhand,

No. 8 = 1011452 blue service gladhand.

Supply Line (Red)

Control Line (Blue)

27

ABS - 4S/2M MERITOR/WABCO COMPONENT KITS



Suggested Electrical Diagram


Four Wheels Sensed

KIT PART NO. 1544222






KIT PART NO. 1544223






KIT PART NO. 1544023



Qty Part No.

Description

1 S4005001030 ECU

1 S4493260300 Power Cable 10 ft

4 S4497130300 10' Sensor Ext Cable

1 ---

1 ---

1 ---

ABS Label For Lamp

Installation Guide

End of Line Test

Qty Part No.

Description

1 S4005001030 ECU

1 S4493260300 10' Power Cable



1 --ABS Label For Lamp

1 ---

1 ---

Installation Guide

End of Line Test


Qty Part No.

Description

1 S4005001030 ECU

1 PEC448 49' Power Ext Cable


1 --ABS Label For Lamp

1 ---

1 ---

Installation Guide

End of Line Test



(2S/2M) Parts Listing of Kit.



KIT PART NO. 1542023

Enhanced Easy-Stop™ Enhanced Easy-Stop™

We have developed these kits for MANUFACTURERS ONLY

- OEM ONLY. These kits are not available to aftermarket distributors - Those kits are on the following pages.

THANK YOU!

4S/2M schematic (showing air)


Qty Part No.

Description

1 S4005001020 ECU

1 PEC448 49' Power Ext Cable

1 S4493260050 1.6' Power Cable


1 ---

1 ---

1 ---

ABS Label For Lamp

Installation Guide

End of Line Test

1011452

6006

616

1010329

6003

6002

1010447

A/C

1010447

SPRING BRAKE CONTROL VALVE

Spring Brake Priority System

3 /

8

"

Control

Complies with all changes to FMVSS121.

Designed for use with a single reservoir on a typical single or tandem axle

3/8"

Delivery

3 /

8

"

Supply trailer application.

Part No. 110500

3/8"

Delivery

1 /

2

"

Reservoir

1011451

S4005001030

(see pg 28)

110500

1010447 1010447


Service Brake

Spring Brake

Supply Line (Red)

Control Line (Blue)

110500 - Spring Brake control valve, R955322 - Wabco ECU valve, 6003 - 3/4" x1/2"hex nipple

6002- 1/2"x 1/2" hex nipple, 6006 - 3/4" pipe nipple, 616 - 1/2"-3/4" nipple 1010329 air tank,

1010447 - spring brake chamber, 1011451 - red emer. gladhand, 1011452 blue svc. gladhand.

28

MERITOR WABCO ABS ENHANCED EASYSTOP™ CONVERSION KITS

Meritor WABCO has created a series of retrofit kits to replace the previous Easy-Stop platform, to the current production Enhanced Easy-Stop platform.

Easy Stop was installed on production built trailers between March 1997 and February 2001.

Enhanced Easy-Stop incorporated current technology to address regulatory PLC requirements and has been installed from March 2001 to present.

To determine the proper kit , find the existing Easy-Stop ECU/Valve part number that needs to be replaced.

Then determine if you will pull the diagnostics from the tractor (power adapter equipped kits) or from the trailer (power adapter with diagnostic adapter equipped kits).

Converting Meritor WABCO Easy Stop to Enhanced Easy-Stop™ Trailer ABS ECU/VALVE

Easy Stop

ECU/Valve#

472 500 021 0

472 500 011 0

472 500 012 0*

472 500 013 0

Description

2S/1M for Trailers

2S/1M for Dollies

Enhanced Easy Stop

Power AdapterRetrofit Kit Power/Diagnostic Adapter Retrofit Kit

R955344

R955322

2S/1M, 2S/2M, 4S/2M R955320

Enhanced Easy Stop

R955345

R955323

R955321

4S/3M R955346 R955347

•If a 472 500 012 0 ECU/Valve was used in an Easy Stop 2S/1M application, order a

R955344 or R955345 kit. Kits contain an Enhanced Easy-Stop ECU/Valve and either a power cable adapter or power/diagnostic cable adapter.

Part No. R955344

(from the tractor)

For Trailer Applications Only

(NO Dolly) 2S/1M

Replaces Meritor

Part Number 4725000210 w/S8946073120 cable

Part No. R955322


For Dollies Only 2S/1M

Replaces Meritor


Part No. R955320


2S/1M, 2S/2M, 4S/2M

Replaces Meritor


Part No. R955345

(from the trailer)

For Trailer Applications Only

(NO Dolly) 2S/1M

Replaces Meritor


Part No. R955323


For Dollies Only 2S/1M

Replaces Meritor


Part No. R955321


2S/1M, 2S/2M, 4S/2M

Replaces Meritor


29

MERITOR WABCO ENHANCED EASYSTOP™ COMPONENTS

Part No. S4005001010

ECU Valve Assembly

2S/1M Basic for trailer

(after the 3/1/01 date)

Part No. S8946073120

Adapter cable. Connects Easystop power cable to enhanced Easystop

ECU/Valve assembly.

Part No. S4461082010

ECU Only

Part No. S4005001020

ECU Valve Assembly



Part No. S4721950330

Relay Valve with boyonet connector. Valve repacement for S4005001010.


Part No. S4005001030

ECU Valve Assembly



Part No. S8946073130

Adapter cable with diagnostic cable.

Connects Easystop power cable to enhanced

Easystop ECU/Valve assembly.

Part No. S8946062752

ABS connector relay

2S/1M Basic.

Part No. S4008506010

ECU Only

Part No. S4008500530

Modulator Valve, 1/2" ports.

Kostal Connector, 12 V

Part No. S4008500540

Modulator Valve, 1/2" ports.

Bayonet Connector, 12 V

Easy Stop

Power Cables

Part No. S8946049440

Power cable, 4 conductor, 3', std connector

Part No. S8946049450


Part No. S8946060380


Part No. S8946060500


Part No. S4493260100

ABS Power Cable

4 conductor, 3.3 feet.

for standard harness connector

Part No. S4493260050 - 1.65 feet.

Part No. S4493260300 - 10 feet. (shown)

Part No. S4493260470 - 15.4 feet.

Part No. S4493641500

13.1' / 9.8' Power "Y" Cable

Part No. S4493641530

20' / 10' Power "Y" Cable3

NOTE: Sensors and Sensor Extensions are Universal to Both Systems

30

2S / 1M AIR KIT BILL OF MATERIALS

We have put together a "typical" 2S/1M air kit for the ABS system, to help complete the installation process.

Part No. 2S/1M-AIR-KIT

Bill of Materials:

1010329 Air Tank, 12" diameter, 29.5" c-c

1011451 Emergency gladhand

1011452 Service gladhand

110500 Spring brake control valve

11300 Frame coupling

1542014 ABS system (see page 25)

16636 Air hose assembly

16648 Air hose assembly

Bill of Materials continued:

218P-12 Hex head plug, 3/4" pipe

218P-6 Hex head plug, 3/8" pipe

269NTA-6-6 Male elbow, 3/8"tube to 3/8" pipe

272NTA-9-9 Male Tee 3/8"tube to 3/8" pipe

6003 Hex Nipple, 3/4"x1/2" MPT

6006 Hex Nipple

68NTA-6-4 Male Connector 3/8"tube to 1/4" pipe

68NTA-6-6 Male Connector 3/8"tube to 3/8" pipe

DCR601-4 Brass valve drain cock

Using this kit as a basis/guide to work from, we can design the kit that you need.

MERITOR WABCO MBS KITS

Wabash National announced that is has discontinued its proprietary ABS products for all production trailers, and we have the complete replacement retrofit kits available for slider suspensions.

Part Number 1532014 (R955382)

2S/1M ABS Kit: INCLUDES:

PLC Select Valve/ECU

Assembly - 6 port

Power Cord Extension

2 Sensor Clips

Heavy Duty Hex Nipple

Installation Instructions

PLC Service Manual

The 1532014 kit has no sensors so that the existing sensors can be used if the existing sensor numbers are

10800126 (Wabash number), or

S4410328080 (Meritor number.)

Also available - R955383 for 4S/2M.

KITS ARE BOXED / 1 BOX PER TRAILER.

Part Number R955374

2S/1M ABS Kit: INCLUDES:

ECU Valve Assembly, sensors (2) 1 ft, power cable 14 ft w/iso plug, sensor extension cables (2) 6 ft w/ plug, sensor springs (2), installation instructions.

Also available - R955375 for 4S/2M.

MBS ABS KITS!

The R955374 includes sensors if the existing sensors are not Meritor, or all new sensors are needed.

31

1810003

MISCELLANEOUS MERITOR WABCO ABS COMPONENTS

Sensor Placement

When more than one wheel is controlled by a single valve, sensors should be mounted at the axle which tends to lock first. For spring suspensions this is usually the forward axle. For air suspensions this is usually the rear most axle.

Right Angle (90°) Sensor Kits

Includes sensor, bushing clip, friction lube, and instructions.

Part No.

Cable lead in Feet

R955335 1.0

R955336 3.0

R955341 5.8

R955342 6.6

ABS Diagnostic (Pre-PLC)

Cable with Tool

Part No.

SA13237L1130

ABS Relay Valve

Second modulator valve for use on 2S/2M and 4S/2M

Systems

Part No. R955378

1810000

1810002

1810003

1810001

Straight Sensor Kits

Includes sensor, bushing clip, friction lube, and instructions.

Part No.

Cable lead in Feet

R955329 5.6

R955337 5.8 (Sensor is 65mm)

R955338 5.8 (Sensor is 79mm)

ABS Relay Valve with bayonet connector.

Valve relplacement for

S4005001010

Part No. S4721950330

Sensor Holder

Part No. S2255U1113

(welded to axle spindle)

Common ABS Components

Part No.

Description

1810000 Bendix /Haldex 1' Sensor

1810001 Friction Bushing / Clip

1810002 Meritor Wabco 1' Sensor

1810003 Meritor Wabco 3' Sensor

S8997605104 Stainless steel friction busing clip

Sensor Extension Cables

Part No.

S4497130180

S4497130300

S4497130500

Cable Feet

6 feet

10 feet

16 feet

ABS Modulator Valve

Controls air pressure to the brake chambers during an

ABS stop.

POWER CABLES

Part No.

ABS Power Cable

4 Cond.,49 feet, w/blunt cut end.

Part No.

S4493151500

Description ( EZ STOP)

S8946049440 ABS Power Cable, 3 feet, with industry standard plug.




Part No. S4008500530

12 volt, kostal style connector.

(screw-on)

Part No. S4008500540

12 volt, bayonet style connector.

32

ABS ELECTRIC CONFIGURATION - 2S/1M - HALDEX PLC - FULL FUNCTION

Kit Part No. AQ961404

PARTS LIST Consisting of:

Qty

1

1

2

1

Part No.

AL919310

AL430624

AL919804

AL919901

1 box -

Description

ECU

Full Function ABS

Valve

7.5' Sensor Cable Ext

12' Power Cord Ext

Tie Down Clips

•PLC Select ECU Design

•FFABS Relay Valve

•3/4" nipple, spring brake priority.

•For Van Trailers

•Complies with the March 2001

PLC4 Trucks industry.

•Kit includes detailed instructions for installation and maintenance.



Qty

1

1

2

1

Part No.

AL919310

AL430624

AL919804

AL918602

1 box -

Description

ECU

Full Function ABS

Valve

7.5' Sensor Cable Ext

62' Power Cord, 38'drop

Tie Down Clips

•PLC Select ECU Design

•FFABS Valve Type

•Reservoir Mount

•Control Port (1) 3/8"-18

•Emergency Supply Port (1)3/8"-18

•Complies with the March 2001

PLC4 Trucks industry.

•Kit includes detailed instructions for installation and maintenance.

ECU

Part No. AL919310

FF ABS Valve

Part No.AL430624

Power Cord

Part No. AL918602

Sensor Cable extension

Part No. AL919804

ABS AIR CONFIGURATION - UNIVERSAL PLC 2S/1M REPLACEMENT KIT

AQ960510 Universal PLC Select ABS Kit will replace all competitive brands and generations of trailer 2S/1M (2 Sensor - One Modulator Valve) ABS systems. These are any systems that utilize a single ABS valve, two sensors, and a separate spring brake control valve. Some additional components unique to the vehicle being upgraded should be expected. Do not use this kit to replace the Haldex FFABS ABS System as this is a single valve per vehicle and spring brake control is integral to the FFABS valve.



Qty

2

1

1

1

1

Description

PLC Select Valve ECU Assy. 6 Port

19 Foot Power Cord Ext.

6.6 foot Sensor Extensions

Installation Instructions L31203

PLC Service Manual L30030

33

ABS PLC SELECT UPGRADE KIT - 2S / 1M

Wheel-speed Sensor and Trailer Power connects directly to

ECU - no intermediate cables required.

Single fastener design assures easy serviceability.

ECU Valve

PLC Select

Part No.

AL919323

Potted ECU Enclosure provides excellent protection from the environment.

Part No.AQ964110

KIT CONTAINS:

1M Power Cord Extension

0.5M Sensor Extensions

PLC Select ECU & Bracket.

•Meets FMVSS121 requirements including March 2001 In-Cab

Malfunction Lamp.

•Embraces “Power Line Carrier” multiplexing technology.

•Standard Electronic Odometer.

•Select Low-High software is standard.

•Sensor and Power Connectors plug directly into the ECU.

•Potted ECU Enclosure

•New Mounting Bracket with single fastener design.

•Standard on-board diagnostic capability

•Compatible with both

PLC InfoCenter and PLC PC.

ABS ELECTRICAL CONFIGURATION - 4S/2M - FULL FUNCTION

ECU

Part No. AL919311

FF ABS Valve

Part No.AL430624

Modulator Valve

Part No. AL364040

Sensor Cable extension

Part No. AL919804



Qty Part No.

Description

1

1

AL919311

AL430624

1

1

2

2

AL919802

AL919804

AL919901

AL364040

1 AL40906

1 box -

ECU

Full Function ABS

Valve

4.5' Sensor Cable Ext.

7.5' Sensor Cable Ext.

12' Power Cord Ext.

Modulator Valve

Loom Assembly

Tie Down Clips

34

ABS Modular Valve less ECU

Part No. AL364040

Single axle application

HALDEX ABS COMPONENTS

FFABS Valve

With integral spring brake control.

Pre-installed reservoir nipple with swivel and locknut feature.

Comes standard with filters in both the control and supply ports.

Part No.

Description

AL430611 4 port, 1/2" nipple,

12 volt, 3/8" ports.

ABS Power Cable

ECU end includes industry standard 5-pin female connector.

7-way end is stripped wires.

For production Mar. '01-present.

Part No.

Length

AL918603 38 feet

ABS lamp lead is 25 feet.

Number of Ports: 2

Mounting Port Size: 1/2 inch

Delivery Port Size: 3/8 inch

Mount: Reservoir

Application: 24mm 12 volt Solenoid.

AL918604 52.5 feet

ABS lamp lead is 26.2 feet.

AL918606 15 feet

ABS lamp lead is 4 feet.

ABS Modular Valve less ECU

Part No. AL364041

Multi-axle application.

•ECU & bracket may need to be transferred from existing valve.

•Use inlet filter A906960 in off-highway applications.

Number of Ports: 6

Mounting Port Size: 1/2 inch

Delivery Port Size: 3/8 inch

Mount: Reservoir

Application: 24mm

12 volt Solenoid

Electronic Control Unit (ECU)

Part No. AL919302

MOD 1 - SLH-A5-19 Pin

• OEM part no. is located on top.

• Post mandate ECU’s include bail latch.

FFABS Valve

Part No.

Description

AL430614 4 port, 3/4" nipple,

12 volt, 3/8" ports

With integral spring brake control.

Pre-installed reservoir nipple with swivel and locknut feature.

Comes standard with filters in both the control and supply ports.

Pin Housing Dimensions:

3-1/2 inch Height x 5-3/8 inch Wide

Application/Notes: Pre-March '01

•ECU & bracket may need to be transferred from existing valve.

•Use inlet filter A906960 in off-highway applications.

Power cord repair kit

5 way terminal kit for power cords.

Part No.

AQ15473

Right Angle (90°) Sensor Kit

Includes sensor, bushing clip.

Part No.

Cable lead

AL10271914 1.6 feet

35

BENDIX ABS COMPONENTS

Bendix ® TABS-6 (Standard)

Trailer Antilock Braking System

Few connections, small and light, fast and reliable, for all applications.

Part No.801855

2S/1M trailer ABS module.

Communicates over PLC.

Has a 4 port relay.

MC-12 Trailer ABS Modules -

Replacement Kit

Part No.802902

The MC-12 trailer ABS modules are no longer available. TABS-6 kits are available for service.

19.5 foot cable, 5-pin ABS pigtail and sensors.

Bendix EC-30™

Electronic Controller -ECU

Part No. 801236

6S/4M -sensors and modulators.

Traction control.

EC-16™ and EC-17™ service replacement.

Bendix MC-30™ trailer ABS module

Part No.800737

Tank mounting. Default config is 4S/2M side, will auto configure to 2S/2M axle, 2S/1M.

LED Diagnostic

Display

30-Pin

Connector

=

A-18 Trailer ABS Modules -

Replacement Kit

Part No. K019711

The A-18 trailer ABS modules are no longer available.

TABS-6 kits are available for service.

ABS Diagnostic Tools

Part No. Description

801869 RDU - Remote Diagnostic Unit

801872 RDU adapter - 6 pin to 9 pin adapter cable

802229 RDU adapter - 9 pin to 9 pin adapter cable

802435 RDU plus 6 pin to 9 pin adapter cable

802436 RDU plus 9 pin to 9 pin adapter cable

802162 TRDU - Trailer Remote Diagnostic Unit

802165 TRDU adapter - 7 pin connector for TRDU

801869

Tractor

RDU

801872

RDU

Adaptor

802229

TRDU

Adaptor

802162

Trailer

TRDU

802165

TRDU

Adaptor

Delivery Ports

3/8" NPT (4)

ABS Modulator

Connector(MOD1)

Supply Port

1/2" NPT

Bendix Pressure Modulator Valves

Part No. System

801481 12 volt, M-32QR™

801666 12 volt, M-32™

801481

Delivery

(port 2)

801666

Control Port

1/2" NPT

Supply

(port 1)

Exhaust

(port 3)

WS-24™ Wheel Speed Sensors

Part No. Description

801546 90°, 60", w/Deutsch connector.

801552 Straight, 75" w/DT04 connector.

801534 Clamping Sleeve

The WS-24™ is compatible with all previous Bendix sensors if used with this clamping sleeve.

Power Cord

MC-30™ cable assembly

Part No. 801697

Supply

(port 1)

BENDIX | MC-30 TRAILER ABS CONTROLLER | User manual | ABS

24

ABS TECH INFO - ARVIN MERITOR

End of Line Testing without TOOLBOX™Software

Sensor Gap Adjustment

Fault Code Check

Blink Code Chart

ABS - 2S/1M, 2S/2M MERITOR/WABCO COMPONENT KITS

KIT PART NO. 1542014

KIT PART NO. 1542015

KIT PART NO. 1542016

2S/1M schematic (showing air)

25

26

ABS - 2S/1M COMPONENT PARTS - SPRING BRAKE PRIORITY

A/C = Anti-Compounding

Service Brake

Spring Brake

Supply Line (Red)

Control Line (Blue)

27

ABS - 4S/2M MERITOR/WABCO COMPONENT KITS

KIT PART NO. 1544222

KIT PART NO. 1544223

KIT PART NO. 1544023

KIT PART NO. 1542023

4S/2M schematic (showing air)

28

MERITOR WABCO ABS ENHANCED EASYSTOP™ CONVERSION KITS

29

MERITOR WABCO ENHANCED EASYSTOP™ COMPONENTS

NOTE: Sensors and Sensor Extensions are Universal to Both Systems

30

2S / 1M AIR KIT BILL OF MATERIALS

MERITOR WABCO MBS KITS

Part Number 1532014 (R955382)

KITS ARE BOXED / 1 BOX PER TRAILER.

Part Number R955374

31

MISCELLANEOUS MERITOR WABCO ABS COMPONENTS

32

ABS ELECTRIC CONFIGURATION - 2S/1M - HALDEX PLC - FULL FUNCTION

ABS AIR CONFIGURATION - UNIVERSAL PLC 2S/1M REPLACEMENT KIT

33

ABS PLC SELECT UPGRADE KIT - 2S / 1M

ABS ELECTRICAL CONFIGURATION - 4S/2M - FULL FUNCTION

34

HALDEX ABS COMPONENTS

35

BENDIX ABS COMPONENTS

ABS Diagnostic Tools

Related manuals

TU-FLO 501 AIR COMPRESSOR

BENDIX

PNU-113

BENDIX

TCH-013-011