- Home
- Domestic appliances
- Small kitchen appliances
- Electric kettles
- Cleveland Range
- MKDL-100-T
- User manual
advertisement
▼
Scroll to page 2
of 55
Operators Manual Installation, Operation & Service Direct Steam Mixer Kettles MODELS: (T) MKDL-40-T (-CC) (T) MKDL-60-T (-CC) (T) MKDL-80-T (-CC)) (T) MKDL-100-T (-CC) (T) MKDL-125-T (-CC) (T) MKDL-150-T (-CC) ™ Cleveland Enodis 1333 East 179th St., Cleveland, Ohio, U.S.A. 44110 Phone: (216) 481-4900 Fax: (216) 481-3782 Visit our web site at www.clevelandrange.com SE95018 Rev. 5 For your safety DANGER Keep clear of pressure relief discharge. Keep hands away from moving parts and pinch points. IMPORTANT Do not fill kettle above recommended level marked on outside of kettle. Inspect unit daily for proper operation. CAUTION Surfaces may be extremely hot! Use protective equipment. Wear protective equipment when discharging hot product. Do not lean on or place objects on kettle lip. Stand clear of product discharge path when discharging hot product. SERVICING Shut off power at main fuse disconnect prior to servicing. 0 Ensure kettle is at room temperature and pressure gauge is showing zero or less prior to removing any fittings. GAS APPLIANCES Do not attempt to operate this appliance during a power failure. Keep appliance and area free and clear of combustibles. INSTALLATION GENERAL Installation of the kettle must be accomplished by qualified installation personnel working to all applicable local and national codes. Improper installation of product could cause injury or damage. This unit is built to comply with applicable standards for manufacturers. Included among those approval agencies are: UL, NSF, ASME/Ntl.Bd., CSA, ETL, CE, and others. Many local codes exist, and it is the responsibility of the owner/installer to comply with these codes. INSPECTION Before uncrating, visually inspect the unit for evidence of damage during shipping. If damage is noticed, do not unpack the unit, follow shipping damage instructions. RECOMMENDED FLOOR DRAIN LOCATION WALL 18" CLEARANCE REQUIRED FOR SERVICE DRAW-OFF VALVE A 6" 12" B 12" C A SHIPPING DAMAGE INSTRUCTIONS If shipping damage to the unit is discovered or suspected, observe the following guidelines in preparing a shipping damage claim. 1. Write down a description of the damage or the reason for suspecting damage as soon as it is discovered. This will help in filling out the claim forms later. If possible, take a polaroid picture. 2. As soon as damage is discovered or suspected, notify the carrier that delivered the shipment. 3. Arrange for the carrier's representative to examine the damage. 4. Fill out all carrier claims forms and have the examining carrier sign and date each form. CLEARANCE REQUIREMENTS This unit must be installed in accordance with the clearances shown on the rating label which is adhered to the unit. FOR YOUR SAFETY. Keep the appliance area free and clear of combustible materials. (T) MKDL-40-T(-CC) (T) MKDL-60-T(-CC) (T) MKDL-80-T(-CC) (T) MKDL-100-T(-CC) (T) MKDL-125-T(-CC) (T) MKDL-150-T(-CC) Recommended Floor Drain Location 22 22 22 21 21 21 1/8" 1/8" 1/8" 3/4" 3/4" 3/4" B C 51" 53" 58" 61" 65" 68" 31" 31" 31" 31" 31" 31" Shim as required to make level with center console (front and back) Jack 4"x4" or larger (front and back) Skid Forklift tongs Flanged feet Recommended Installation Procedure MOVING UNIT 1. While still on skid, move unit as close to final installation position as possible. 4. Lower gently to ground and remove forklift and blocking. 2. Prepare unit for lifting as shown in diagram. 5. 3. Lift gently with a forklift or jacks and remove skid. If unit has to be re-positioned, slide gently. Do not twist or push one side of unit excessively and cause binding on trunnions. Note: Instructions reflect a more complicated twin mixer kettle - process for single mixer kettles is the same. LEVELING B A B A 3. Level consoles individually from front to back (dotted lines C). Adjustments are made by turning flanges on front feet only. 4. Re-check that the back is level (dotted line B) and then the front (dotted line D). Adjust if necessary. C C C 5. Check that mixer bridge is level and guide pins lock smoothly without binding. If not repeat steps 1 through 4. C C C D D Guide Pins NOTE: See Operating Instructions before operating unit. Recommended Leveling Procedure 6. Make electrical connections (see electrical service connections) and test mixer bridge as follows: 1. With straight-edge, line the backs of the consoles up with each other (dotted line A). ⇒ A/ Raise mixer bridge. 2. Level and straight-edge backs of consoles (dotted line B). Adjustments are made by turning flanges on back feet only. ⇒ C/ Swing bridge to the left as far as possible. ⇒ B/ Swing bridge out over centre console. ⇒ D/ Lower bridge. COMPRESSED AIR CONNECTION ⇒ E/ Bridge pins should enter pin hole on kettle perfectly, If not return to step 1 and repeat leveling steps. Mixer Kettles with an air activated discharge valve require a minimum of 90 PSI to operate correctly. ⇒ F/ Raise bridge and swing to far right (for twin mixers only). If the unit is also supplying air to a Metering Filling Station then a pressure of 100 PSI at a minimum volume of 25 CFM is required. ⇒ G/ Repeat steps D and E (for twin mixers only). 7. Once positioned and leveled, permanently secure the kettle's flanged feet to the floor using 5/16 inch stainless steel lag bolts and floor anchors (supplied by the installer). Secure each of the flanged feet with one bolt in each hole. 8. Connect piping as described in the "PIPING CONNECTION" section. The air supplied to the mixer should be clean and dry. No oil should be added to the supply air. We recommend the compressed air system be equipped with a drier, filter, and automatic water dump on the air compressor receiver tank. If the distance between the tank and the unit is less than 100 feet then a minimum line size of 3/4" is required. A distance of 100 to 300 feet requires a minimum 1" line. PIPING CONNECTIONS ELECTRICAL SERVICE CONNECTIONS Install in accordance with local codes and/or the National Electric Code ANSI/NFPA No 70-1981 (USA) or the Canadian Electric Code CSA Standard C22.1 (Canada). A separate fused disconnect switch must be supplied and installed. The kettle must be electrically grounded by the installer. The electric supply must match the power requirements specified on the kettle's rating plate. The copper wiring must be adequate to carry the required current at the rated voltage. Refer to the specification sheet for electrical specifications. 1. Ensure main power is turned off before connecting wires. 2. Remove the screws at the rear of the center console cover, and remove the cover. A wiring diagram is affixed to the underside of the console cover. 3. Feed permanent copper wiring 18" through the cut-out in the bottom of the console. Connect wiring in junction box in the bottom of the console. 4. Turn main power back on. 5. Check for correct rotation of electric motor (access by removing top front cover on center console). If rotation is incorrect, disconnect main power and reverse any two of the three live lines. 6. Replace the console cover and secure it with screws. 1. All plumbing to and from the kettle should be thoroughly cleaned and inspected for dirt and debris before the final connections to the kettle are made. 2. Connect all piping according to identification tags on unit. 3. Piping between boiler and kettle should be sloped and a drip condensate trap installed at lowest point. 4. Insulating steam piping is recommended for safety and higher efficiency. 5. To determine the correct steam supply pipe size: ⇒ A/ Find the total steam requirement using the first chart. ⇒ B/ Use the steam requirement total in the second chart to find the correct pipe size. DUMP VALVE TO DRAIN PIPING SCHEMATIC CONDENSATE OUT STEAM IN HOT WATER COOLING WATER IN COLD WATER COOLING WATER OUT GLOBE VALVES PRESSURE REDUCING VAVLE PVR UNIONS STRAINERS STEAM REQUIREMENTS FOR KETTLES Kettle Cap. U.S. Gal. Kettle Dia. 40 60 80 100 125 150 26" 29.5" 33" 36" 40" 40" 25 psi Steam 265°F Lbs./Hr. Hp./Hr. 100 150 210 260 320 390 3 4.5 6.0 7.5 9.5 11.0 40 psi Steam 287°F Lbs./Hr. Hp./Hr. 120 190 260 320 400 480 4 5.5 7.5 9.5 11.5 14.0 80 psi Steam 302°F Lbs./Hr. Hp./Hr. 150 230 300 390 470 570 4.5 7.0 9.0 11.0 14.0 17.0 Steam requirements are maximum per hour. If more than one unit is on the same line then add the steam usage for each one to reach a total. STEAM PIPE SIZING NOTES: Required pipe length in feet/meters Steam Required Lbs./Kg. per hour 100/45 Kg. 200/91 Kg. 300/136 Kg. 400/182 Kg. 500/227 Kg. 700/318 Kg. 900/409 Kg. 200 Ft. 60 Meters 3/4" 1" 1" 1" 1 1/4" 1 1/2" 1 1/2" 400 Ft. 125 Meters 1 1 1 1 1 1 1" 1/4" 1/4" 1/2" 1/2" 3/4" 3/4" 600 Ft. 185 Meters 1 1 1 1 1 1/4" 1/2" 1/2" 3/4" 3/4" 2" 2" Pipe size in inches. Less than 50 PSI (3.4 BAR) pressure, increase pipe size by 1/4". 80 to 100 PSI (5.5 to 6.8 BAR), Decrease pipe size by 1/4". QUALITY ASSURANCE CHECKLIST Follow this list only after all other installation steps are completed. Some steps require the use of equipment. Follow operating instructions. The following will be performed before the unit is connected to utilities: 1. Visual Examine unit for scratches, dents, or other defects. 2. Visual Check flanged feet all have bolts holding them. 3. General Check all accessible wiring, mechanical and plumbing connections by hand for secure, tight and satisfactory assembly. Remove all paper. 4. Level Check unit has been leveled and squared correctly. The following will be performed with the unit connected to utilities: 5. Raise Bridge If bridge does not raise then check motor rotation. Bridge should not raise until speed control is turned to minimum and then adjusted back up. 6. Swing Bridge Bridge when fully raised should swing without hitting any object, i.e. control housing, kettle lip. Check that hydraulic hoses are not being pinched by stops on swivel assembly. 7. Kettle tilts smoothly both down and back up. If power tilt, check that micro switches are adjusted properly (kettle is level in upright position and drains fully when tilted) and are not being crushed by gear. Tilt Kettle 8. Lower Bridge Raise bridge. Switch to mix. Turn speed control to zero to reset micro switch then set speed control to number four. Check that unit does not begin to mix until bridge has lowered part way into the kettle. Check that mixer bridge pin lowers into pin hole correctly 9. Speed Control Main Main agitator arm not rotating when set at minimum but will start to move slowly on one. Speed control makes positive contact with micro switch. 10. Speed Control Secondary Set main speed control to five. Adjust secondary control from minimum to maximum. Look for considerable speed variance. 11. Water Faucets Turn on hot water faucet. Turn off and check for leaks in piping and drips from faucet spout. Repeat above with cold water faucet. 12. Product Discharge Add water to kettle. Check for leaks from valve. Open and close valve a few times Valve and check for leaks again. OPTIONAL CONTROLS Some units may not have the following items to test 13. Meter Complete this test using markings on mixer arm or a measuring strip if there are no markings on the unit. Test the meter at the following values up to capacity (Should be approx. ±1/4"). During this test check that the (interrupt) switch stops the water flow and the (continue/reset) when switched to "continue" resumes the flow without resetting the meter. GALLONS 5 20 40 80 100 LITERS 20 80 160 320 400 When the (continue/reset) switch is turned to "reset" the displayed quantity on the meter should be erased and the count begins at zero. For the following test fill the kettle 3/4 full of water. Have the mixer rotating with the speed control setting at three to five. 14. Heating Manual (Active/Bypass) switch in "Bypass" position. (Heat/Off/Cool) switch in "Heat" position. Open manual steam valve, steam enters kettle and condensate escapes from steam trap. For units equipped with water cooling 1./ Automatic drain opens and discharges water from jacket, 2./ Automatic drain closes when steam starts exiting, 3./ Condensate drain opens and discharges hot water. Close manual steam valve and you should hear steam entering kettle slow to a stop. 15. Cooling Manual Turn (Heat/Off/Cool) switch to "Off". Open manual steam valve. Turn (Heat/Off/Cool) switch to "Cool". Cooling water enters kettle from large console and exits from side console. 16. Heating Automatic (Heat/Off/Cool) switch in "Off" position. Open manual steam valve. Follow operating instructions on label to set the temperature to 180°F/ 90°C. Turn (Active/Bypass) switch to "Active", you should hear steam entering kettle and condensate should escape steam trap. For units equipped with water cooling 1./ Automatic drain opens and discharges water from jacket, 2./ Automatic drain closes when steam starts exiting, 3./ Condensate drain opens and discharges hot water. 17 Chart Recorder a) Seal chart recorder on the inside all around to the panel with silicone. b) Seal pipe penetration where cables enters panel from console with silicone all around. OPERATING INSTRUCTIONS Operating Controls & Indicators for Standard Direct Steam Mixer Kettles ITEM NO. DESCRIPTION FUNCTION 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. Air Quick Connect . . . . . . . . . .Connection for air to food pump. Air Regulator . . . . . . . . . . . . . .Opens and closes air operated product discharge valve (Item 10). Hand Wheel . . . . . . . . . . . . . .Tilts kettle for pouring. May be replaced by tilt switch if unit is power tilt. Steam Valve . . . . . . . . . . . . . .Manually controls the amount of steam entering the kettle. Scraper Blades . . . . . . . . . . . .Scrapes the side of the kettle and moves product away. Main Agitator Arm . . . . . . . . . .Provides most of the product movement. Temperature Probe . . . . . . . . .Probe holds temperature sensors for controller. Secondary Arm . . . . . . . . . . . .Provides reverse agitation and product lift in kettle. Drain Cock . . . . . . . . . . . . . . .Used to manually drain condensate from kettle. Product Discharge Valve . . . .Discharge valve for product in the kettle. Mixer Bridge . . . . . . . . . . . . . .Encloses agitator motors. Secondary Speed Control . . .Controls speed of secondary agitator arm. Faucet Spout . . . . . . . . . . . . . .Delivers water to the kettle. Hot Water Valve . . . . . . . . . . . .Turns on hot water. Cold Water Valve . . . . . . . . . . .Turns on cold water. Mixer Speed Control . . . . . . . .Controls speed of agitators and mixer bridge lift mode. Mix/Lift Switch . . . . . . . . . . . . .Sets hydraulics to mix or lift mode. Up/Down Switch . . . . . . . . . . .When unit is in lift mode, bridge can be raised or lowered with this switch. Emergency Stop . . . . . . . . . . .Stops hydraulic system. On/Off Switch . . . . . . . . . . . . .Power switch to water meter. Start Switch . . . . . . . . . . . . . . .Starts water flow to kettle. Interrupt Switch . . . . . . . . . . . .Interrupts flow without resetting water meter. Active/Bypass Switch . . . . . . .Switch to activate or bypass (manual operation) the controller. Controller Switch . . . . . . . . . . .Dual function switch for auto mode or manual heat, cool or off mode. Main Power Switch . . . . . . . . .Power switch for unit. Water Meter Control . . . . . . . .Display and setting for water meter. Operating Controls & Indicators for Cook Chill Direct Steam Mixer Kettles ITEM NO. DESCRIPTION FUNCTION 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. Air Quick Connect . . . . . . . . . .Connection for air to food pump. Air Regulator . . . . . . . . . . . . . .Opens and closes air operated product discharge valve (Item 10). Hand Wheel . . . . . . . . . . . . . .Tilts kettle for pouring. May be replaced by tilt switch if unit is power tilt. Steam Valve . . . . . . . . . . . . . .Manually controls the amount of steam entering the kettle. Scraper Blades . . . . . . . . . . . .Scrapes the side of the kettle and moves product away. Main Agitator Arm . . . . . . . . . .Provides most of the product movement. Temperature Probe . . . . . . . . .Probe holds temperature sensors for controller. Secondary Arm . . . . . . . . . . . .Provides reverse agitation and product lift in kettle. Drain Cock . . . . . . . . . . . . . . .Used to manually drain condensate from kettle. Product Discharge Valve . . . .Discharge valve for product in the kettle. Mixer Bridge . . . . . . . . . . . . . .Encloses agitator motors. Secondary Speed Control . . .Controls speed of secondary agitator arm. Faucet Spout . . . . . . . . . . . . . .Delivers water to the kettle. Hot Water Valve . . . . . . . . . . . .Turns on hot water. Cold Water Valve . . . . . . . . . . .Turns on cold water. Mixer Speed Control . . . . . . . .Controls speed of agitators and mixer bridge lift mode. Mix/Lift Switch . . . . . . . . . . . . .Sets hydraulics to mix or lift mode. Up/Down Switch . . . . . . . . . . .When unit is in lift mode, bridge can be raised or lowered with this switch. Emergency Stop . . . . . . . . . . .Stops hydraulic system. Controller Keypad . . . . . . . . . .Used to set temperature parameters. On/Off Switch . . . . . . . . . . . . .Power switch to water meter. Start Switch . . . . . . . . . . . . . . .Starts water flow to kettle. Interrupt Switch . . . . . . . . . . . .Interrupts flow without resetting water meter. Active/Bypass Switch . . . . . . .Switch to activate or bypass (manual operation) the controller. Controller Switch . . . . . . . . . . .Dual function switch for auto mode or manual heat, cool or off mode. Main Power Switch . . . . . . . . .Power switch for unit. Water Meter Control . . . . . . . .Display and setting for water meter. Operating Suggestions OFF ON General Operation 1. Turn MAIN POWER SWITCH to "ON". Cleveland Range Mixer Kettles are simple and safe to operate. The following tips will allow you to maximize the use of your new mixer. 1. To achieve optimum performance on tilting kettles; Before applying steam to a cold kettle, open the DRAIN COCK to drain condensate from the kettles jacket. Close drain cock when unit is fully drained. 2. Allow unit to preheat before addition of product to kettle. However when cooking egg and milk products, the kettle should NOT be preheated, as products of this nature adhere to hot cooking surfaces. These types of foods should be placed in the kettle before heating is begun. OFF MIX LIFT WARNING- Insure FAUCET SPOUT is out of way before raising or lowering bridge. 1. Turn MIX/LIFT SWITCH to "LIFT". UP OFF DOWN 3. An important part of kettle cleaning is to prevent foods from drying on. For this reason, cleaning should be completed immediately after cooked foods are removed. Refer to the "Care and Cleaning" instructions for detailed kettle washing procedures. 4. If a mixer bridge is equipped with a temperature probe for a controller or thermometer, the probe must be submerged a minimum of three inches in the product for accurate readings. Safety 1. Close PRODUCT DISCHARGE VALVE before filling the kettle. Lifting & Lowering Bridge OFF MIX LIFT 2. Turn MIXER SPEED CONTROL to "MIN" and back up to #5. 3. Turn and hold UP/DOWN SWITCH "UP" to raise or "DOWN" to lower. Mixing 1. Turn MIX/LIFT SWITCH to "MIX". 2. Turn MIXER SPEED CONTROL to "MIN" and slowly adjust to desired speed. 3. Adjust SECONDARY SPEED CONTROL to desired speed. 2. When raising or lowering MIXER BRIDGE, insure FAUCET SPOUT is not in the way of MAIN AGITATOR ARM or damage to spout will result. 3. As a safety precaution the MIXER SPEED CONTROL must first be turned to zero before unit will start to mix. 4. Always remember, like a cooking pot the kettles become very hot when cooking. Avoid contact with bare skin. Tilting Kettle 1. Raise MIXER BRIDGE and swing to side. 2. For manual tilt: turn HANDWHEEL. 3. For power tilt: turn switch " " to raise, or " " to tilt. WARNING- Do not tilt kettle when mixer agitators are in kettle bowl. Discharge Valve BYPASS ACTIVE 1. For air valve: turn AIR REGULATOR clockwise to open, or counterclockwise to close. Manual Heating/ Cooling 1. Turn ACTIVE/BYPASS SWITCH to "BYPASS". OFF HEAT AUTO COOL 2. For butterfly valve: push handle in and pull upwards to open. 2. Turn CONTROLLER SWITCH to "HEAT" or "COOL". 3. For heat: open STEAM VALVE completely to boil, or adjust to regulate temperature. Adding Water Manually For cooling: open STEAM VALVE completely. 1. Locate FAUCET SPOUT over desired kettle. 2. Turn on HOT or COLD WATER VALVES. Upper Display DIGITAL WATER METER OPERATING INSTRUCTIONS 3 2000 Lower Display 1930 Note: The digital counter has been preset at the factory and should operate satisfactory. If installing a new counter (or the configuration settings to your existing digital counter become corrupted) you must configure the digital counter as shown below (Configuring a Digital Counter) prior to operation. PST OUT PGM ENT CONTINUE RESET Program Indicator ON 1 Turn POWER switch "ON". Turn START switch to "RESET". Delivery will start at "0" and stop at preset volume. INTERRUPT RST Next Key Enter Key To stop delivery at any time, turn INTERRUPT switch to " ". Reset Key CONTINUE RESET OFF 4 5 Down Key Locate delivery spout over desired kettle. 2 Set required volume by first pushing the key until the digit you want to change is flashing in the lower display. Then use the key to change the value of the selected digit. When all digits are set, press the ENT key. OFF 6 To complete delivery after interrupting, turn START switch to "CONTINUE" ON 7 Turn POWER switch to "OFF" when meter is not in use. Changing Functions & Options CAL 9900 Hi ˚C Process Temperature or Set Point Sp Lo The controller has been preset at the factory and should operate satisfactory. If you wish to fine tune the unit for your specific application consult the CAL 990O Installation and Operation Manual. Following is a simplified procedure for changing parameters. SP1 Error OFF ON 1. Mixer MAIN POWER switch in the "ON" position. SP2 BYPASS ACTIVE * * * * p View Set Point Decrease Increase CAL 9900 Controls Drawing MIXER KETTLE OPERATION USING CAL 9900 Note: Temperature probe on mixer bridge must be covered with a minimum of three inches of product to function correctly. 2. ACTIVE/BYPASS switch in "BYPASS" position. 3. Press button labeled (p). The display should show a number with a decimal place in it. Left of the decimal place is the OPERATING MODE setting (this number should be flashing). To the right is the FUNCTION NUMBER. 4. To change the OPERATING MODE setting push the ( ) or ( ) buttons. CAL 9900 * p CAL 9900 * ˚C ˚C p 1. Open STEAM VALVE completely OFF ON OFF HEAT AUTO COOL BYPASS ACTIVE 2. Turn mixer MAIN POWER switch to "ON" (CAL 9900 lights up and displays present temperatures). 3. Turn HEAT/COOL switch to “OFF/AUTO". 4. Turn ACTIVE/BYPASS switch to "BYPASS". The unit should not be heating or cooling at this point. 5. Push ( ) button on CAL 9900 to read set point temperature. (This is the desired product temperature). * 6. To change set point temperature push and hold ( ) button while pushing ( ) or ( ) button. New set point is determined when ( ) button is released. * * 7. Add product to kettle. 8. Turn ACTIVE/BYPASS switch to “ACTIVE”. If the set point temperature is higher than the product temperature, the kettle will start heating. 5. To move to the FUNCTION NUMBER (right of the decimal) push ( ) button. * 6. That number should now be flashing. To move to another FUNCTION NUMBER push the ( ) or ( ) buttons. * 7. Push ( ) button to move to the left of the decimal. To change the OPERATING MODE setting push the ( ) or ( ) buttons. CAL 9900 * p CAL 9900 * ˚C p CAL 9900 * ˚C ˚C p BYPASS ACTIVE Note: For twin kettles, the CAL 9900 will control the kettle the mixer is in. 8. When your changes are complete push the button labeled (p) again to return to the Process Temperature. CAL 9900 * p ˚C Cleveland Range Factory Settings OPERATING FUNCTION MODE NUMBER 0 0 0 1 5 2 0 3 4 steam 4 5 electric 0 5 5 6 0 7 0 8 1 9 0 10 0 11 0 12 0 13 0 14 0 15 9 16 17 0 0 18 1 19 2 T.A.P 20 0 0 21 0 = °C 22 1 = °F 6 23 -- -24 0 25 -- -26 OFF MAN ON Pen Display OUT1 OUT2 ALRM SP ˚C ˚F U Pen1 key AUTO/MAN SCROLL Key AUTO MAN OFF HEAT AUTO COOL UP Key DOWN Key BYPASS ACTIVE MIXER KETTLE OPERATION USING MRC 7000 (1 PEN) Note: Temperature probe on mixer bridge must be covered with a minimum of three inches of product to function correctly. 1. Turn MAIN POWER switch to "ON". 2. Turn HEAT/COOL switch to "OFF/AUTO". Manual MAN Setpoint Heat Cooling Output 1 Output 2 3. Turn ACTIVE/BYPASS switch to "ACTIVE". Alarm 4. Open steam valve completely. OUT1 OUT2 ALRM 5. On controller keypad push and hold key " " or " " until desired temperature is set. SP Minus Sign ˚C ˚F ˚U 6. To start: push scroll key " " until "CtrL" is displayed. 7. Push down key " MRC 7000 Controls Drawing (1 pen) ". 8. To stop: push scroll key " " until "OFF " is displayed. 9. Push down key " ". NOTE: For twin kettles, the MRC 7000 will control the kettle the mixer is in. OFF HEAT AUTO COOL BYPASS ACTIVE If the unit is used continually it may be simpler to control the "ON/OFF " function with the following steps: 1. Keep HEAT/COOL switch at "OFF/AUTO". 2. To stop turn ACTIVE/BYPASS switch to "BYPASS". BYPASS ACTIVE 3. To change temperature setting push and hold key " " or " " until desired temperature is set. 4. To start, turn ACTIVE/BYPASS switch to "ACTIVE". CLEANING INSTRUCTIONS CAUTION SURFACES MAY BE EXTREMELY HOT! CARE AND CLEANING Cooking equipment must be cleaned regularly to maintain its fast, efficient cooking performance and to ensure its continued safe, reliable operation. The best time to clean is shortly after each use (allow unit to cool to a safe temperature). CLEANING INSTRUCTIONS 1. Turn unit off. 2. Remove drain screen (if applicable). Thoroughly wash and rinse the screen either in a sink or a dishwasher. 3. Prepare a warm water and mild detergent solution in the unit. 4. Remove food soil using a nylon brush. 5. Loosen food which is stuck by allowing it to soak at a low temperature setting. 6. Drain unit. WARNINGS ➩ 7. Rinse interior thoroughly. Do not use detergents or cleansers that are chloride based or contain quaternary salt. Chloride Cleaners ➩ Do not use a metal bristle brush or scraper. 8. If the unit is equipped with a Tangent Draw-Off Valve, clean as follows: a) Disassemble the draw-off valve first by turning the valve knob counter-clockwise, then turning the large hex nut counter-clockwise until the valve stem is free of the valve body. b) In a sink, wash and rinse the inside of the valve body using a nylon brush. c) Use a nylon brush to clean tangent draw-off tube. d) Rinse with fresh water. e) Reassemble the draw-off valve by reversing the procedure for disassembly. The valve's hex nut should be hand tight only. Wire Brush & ➩ Steel wool should never be used for cleaning the stainless steel. 9. If the unit is equipped with a Butterfly Valve, clean as follows: a) Place valve in open position. b) Wash using a warm water and mild detergent solution. Steel Pads c) Remove food deposits using a nylon brush. ➩ Unit should never be cleaned with a high pressure spray hose. d) Rinse with fresh water. e) Leave valve open when unit is not in use. 10. Using mild soapy water and a damp sponge, wash the exterior, rinse, and dry. NOTES High Pressure Spray Hose ➩ Do not leave water sitting in unit when not in use. ➩ For more difficult cleaning applications one of the following can be used: alcohol, baking soda, vinegar, or a solution of ammonia in water. ➩ Leave the cover off when the kettle is not in use. Stagnant Water ➩ For more detailed instructions refer to the Nafem Stainless Steel Equipment Care and Cleaning manual (supplied with unit). SCRAPER BLADES PRODUCT VALVE 1. Remove retaining ring and slide scraper blades off agitator arm. Daily - clean product valve as follows: 2. Place parts in a pan of warm water to soak. KETTLE 3. Clean in a sink, using a warm water and mild detergent solution. KETTLE OUTLET 4. Rinse with fresh water. CLAMP 5. Allow to dry thoroughly on a flat, clean surface. 0-RING VALVE TEE 0-RING CLAMP 0-RING CLOSED POSTITION OPEN POSITION AIR HOSE AIR CYLINDER AIR HOSE 1. Open product valve. 2. Disconnect air hoses. 3. Remove air cylinder. 4. Remove valve tee. 5. Remove all O-rings. 6. Clean air cylinder, do not submerge in water. Wipe clean and sanitize. 7. Clean and sanitize tee and O-rings. 8. Grease and reinstall O-rings. 9. Reinstall tee to kettle outlet. 10. Reinstall air cylinder to bottom of tee. 11. Reconnect air hoses. 12. Close valve and check for alignment. STAINLESS STEEL EQUIPMENT CARE AND CLEANING (Suppied courtesy of Nafem. For more information visit their web site at www.nafem.org) Contrary to popular belief, stainless steels ARE susceptible to rusting. 4. Treat your water. Though this is not always practical, softening hard water can do much to reduce deposits. There are certain filters that can be installed to remove distasteful and corrosive elements. To insure proper water treatment, call a treatment specialist. Corrosion on metals is everywhere. It is recognized quickly on iron and steel as unsightly yellow/orange rust. Such metals are called “active” because they actively corrode in a natural environment when their atoms combine with oxygen to form rust. Stainless steels are passive metals because they contain other metals, like chromium, nickel and manganese that stabilize the atoms. 400 series stainless steels are called ferritic, contain chromium, and are magnetic; 300 series stainless steels are called austenitic, contain chromium and nickel; and 200 series stainless, also austenitic, contains manganese, nitrogen and carbon. Austenitic types of stainless are not magnetic, and generally provide greater resistance to corrosion than ferritic types. With 12-30 percent chromium, an invisible passive film covers the steel’s surface acting as a shield against corrosion. As long as the film is intact and not broken or contaminated, the metal is passive and stain-less. If the passive film of stainless steel has been broken, equipment starts to corrode. At its end, it rusts. 5. Keep your food equipment clean. Use alkaline, alkaline chlorinated or non-chloride cleaners at recommended strength. Clean frequently to avoid build-up of hard, stubborn stains. If you boil water in stainless steel equipment, remember the single most likely cause of damage is chlorides in the water. Heating cleaners that contain chlorides have a similar effect. 6. Rinse, rinse, rinse. If chlorinated cleaners are used, rinse and wipe equipment and supplies dry immediately. The sooner you wipe off standing water, especially when it contains cleaning agents, the better. After wiping equipment down, allow it to air dry; oxygen helps maintain the stainless steel’s passivity film. Enemies of Stainless Steel There are three basic things which can break down stainless steel’s passivity layer and allow corrosion to occur. 7. Never use hydrochloric acid (muriatic acid) on stainless steel. 8. Regularly restore/passivate stainless steel. 1. Mechanical abrasion 2. Deposits and water Recommended cleaners for specific situations 3. Chlorides Job Cleaning Agent Comments Mechanical abrasion means those things that will scratch a steel surface. Steel pads, wire brushes and scrapers are prime examples. Routine cleaning Soap, ammonia, detergent, Medallion Apply with cloth or sponge Fingerprints & smears Arcal 20, Lac-O-Nu Ecoshine Provides barrier film Stubborn stains & discoloration Cameo, Talc, Zud, First Impression Rub in direction of polish lines Grease & fatty acids, blood, burnt-on-foods Easy-off, De-Grease It Oven Aid Excellent removal on all finishes Grease & oil Any good commercial detergent Apply with sponge or cloth Restoration/Passivation Benefit, Super Sheen Water comes out of the faucet in varying degrees of hardness. Depending on what part of the country you live in, you may have hard or soft water. Hard water may leave spots, and when heated leave deposits behind that if left to sit, will break down the passive layer and rust stainless steel. Other deposits from food preparation and service must be properly removed. Chlorides are found nearly everywhere. They are in water, food and table salt. One of the worst chloride perpetrators can come from household and industrial cleaners. So what does all this mean? Don’t Despair! Here are a few steps that can help prevent stainless steel rust. 1. Use the proper tools. When cleaning stainless steel products, use non-abrasive tools. Soft cloths and plastic scouring pads will not harm steel’s passive layer. Stainless steel pads also can be used but the scrubbing motion must be in the direction of the manufacturers’ polishing marks. 2. Clean with the polish lines. Some stainless steel comes with visible polishing lines or “grain.” When visible lines are present, always scrub in a motion parallel to the lines. When the grain cannot be seen, play it safe and use a soft cloth or plastic scouring pad. Review 1. Stainless steels rust when passivity (film-shield) breaks down as a result of scrapes, scratches, deposits and chlorides. 2. Stainless steel rust starts with pits and cracks. 3. Use the proper tools. Do not use steel pads, wire brushes or scrapers to clean stainless steel. 4. Use non-chlorinated cleaners at recommended concentrations. Use only chloride- free cleaners. 5. Soften your water. Use filters and softeners whenever possible. 6. Wipe off cleaning agent(s) and standing water as soon as possible. Prolonged contact causes eventual problems. 3. Use alkaline, alkaline chlorinated or non-chloride containing cleaners. While many traditional cleaners are loaded with chlorides, the industry is providing an ever-increasing choice of non-chloride cleaners. If you are not sure of chloride content in the cleaner used, contact your cleaner supplier. If your present cleaner contains chlorides, ask your supplier if they have an alternative. Avoid cleaners containing quaternary salts; it also can attack stainless steel and cause pitting and rusting. To learn more about chloride-stress corrosion and how to prevent it, contact the equipment manufacturer or cleaning materials supplier. Developed by Packer Engineering, Naperville, Ill., an independent testing laboratory. SERVICE PARTS WARRANTY Our Company supports a worldwide network of Maintenance and Repair Centers. Contact your nearest Maintenance and Repair Centre for replacement parts, service, or information regarding the proper maintenance and repair of your cooking equipment In order to preserve the various agency safety certification (UL, NSF, ASME/Ntl. Bd., etc.), only factory-supplied replacement parts should be used. The use of other than factory supplied replacement parts will void warranty. 1 51 HYDRAULIC COMPONENTS 7 6 Scraper Blades: 8 5 9 41 47 KETTLE SIZE GALLONS 10 QUANTITY 40 22 60 26 80 30 100 34 125 38 150 38 46 52 39 40 4 3 11 43 12 38 2 37 1 44 36 13A 48 13B 14 15 35 42 34 50 49 16 30 18 32 19 Cooling Fan: 20 Fan . . . . . . . . KE54860 Fan Cover . . . KE601236 Fan Guard . . . KE54861 31 29 21 22 23 33 28 27 24 25 26 NOTE: For Hydraulic Hoses order Part No. RT00505 and specify length required ITEM NO. PART NO. DESCRIPTION 1. 2. KE51607 KE54834-10 SE50224 KE51608 KE54834-11 SE50224 KE51848 SE50241 SE50242 KE52124 KE51846 KE51938 KE53004 FA95006 KE51845 KE53005 KE51715 KE51716 KE52114 FA11286 FA11346 KE52115 CT50097 KE53962 Flow Control Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Solenoid Valve, 2 Way, 120 Volt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Coil Only 120 Volt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Check Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Solenoid Valve, 3 Way, 120 Volt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Coil Only 120 Volt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Rod Gland Seal Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Piston Seal Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Jack Upper Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Hydraulic Motor, Scraper Arm, 40 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Hydraulic Motor, Scraper Arm, 60-150 gal. Hydraulic Motor, Scraper Arm, 200-250 gal. Woodruff Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Hydraulic Motor, Secondary Agitator, 40-150 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Hydraulic Motor, Secondary Agitator, 200-250 gal. Main Coupling, Scraper Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Secondary Coupling, Agitator Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Coupling Washer, Primary S.S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Socket Head Screw, 1/4 X 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Socket Head Screw, 5/16 X 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Coupling Washer, Secondary S. S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 R.T.D Probe Single . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Blade Stop Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13A. 13B. 14. 15. 16. QTY. 18. 19. 20. 21. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 46. 47. 48. 49. 50. 51. 52. KE51834 KE51875-3 KE51875-4 KE51875-5 KE51889 KE52222 KE52222-1 KE52223 KE52224 KE52190 KE52171 KE51844 FI05060 SE50280 FI05061 SE50094 KE51874 KE52382 KE00860 KE51622 FA95022 KE51623 SE50353 KE51624 KE50295 KE50294 FA95055-3 T40527 T40528 T40529 T40530 T40531 T40532 T405321 T405322 KE51921 KE51925 FA19506 FA19507 KE00935 KE00936 KE00937 KE00938 KE00939 KE00940 KE009401 KE009402 KE00947 KE00948 KE00949 KE00950 KE00951 KE00952 KE009521 KE009522 KE00947-1 KE00948-1 KE00949-1 KE00950-1 KE00951-1 KE00952-1 KE009521-1 KE009522-1 KE52687 RT00505 KE00715 Scraper Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .as required Electric Motor, 3 hp., 208-230/460V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Electric Motor, 3 hp., 220/380/440V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Electric Motor, 3 hp., 575V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Filter, Tank Breather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Gear, 3/4" I.D. Pump, prior to 1995 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Gear, 3/4" I.D. Pump, after 1995 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Gear, 7/8" I.D. Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Nylon Coupling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Speed Control Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Gasket, Oil Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Hydraulic Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Swivel adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Hydraulic Hose, Per Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Swivel Elbow. 90 Degrees . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Oil Filler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Pressure Relief Valve, Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Pressure Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Speed Control Cable Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Bridge Tilt Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Retaining Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Clevis Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Clevis Pin c/w Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Knuckle Joint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Mounting Bracket, Mercury Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Mercury Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2 Woodruff Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Housing, probe, 40 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Housing, probe, 60 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Housing, probe, 80 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Housing, probe, 100 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Housing, probe, 125 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Housing, probe, 150 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Housing, probe, 200 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Housing, probe, 250 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Pin, Scraper Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Pin, Secondary Agitator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Set Screw, Secondary Agitator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Set Screw, Scraper Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Secondary Agitator, 40 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Secondary Agitator, 60 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Secondary Agitator, 80 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Secondary Agitator, 100 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Secondary Agitator, 125 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Secondary Agitator, 150 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Secondary Agitator, 200 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Secondary Agitator, 250 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Primary Agitator, 40 gal., with Gallon Markings (includes #16, 18 & 43) . . . . . . . . . . . . . .1 Primary Agitator, 60 gal., with Gallon Markings (includes #16, 18 & 43) . . . . . . . . . . . . . .1 Primary Agitator, 80 gal., with Gallon Markings (includes #16, 18 & 43) . . . . . . . . . . . . . .1 Primary Agitator, 100 gal., with Gallon Markings (includes #16, 18 & 43) . . . . . . . . . . . . .1 Primary Agitator, 125 gal., with Gallon Markings (includes #16, 18 & 43) . . . . . . . . . . . . .1 Primary Agitator, 150 gal., with Gallon Markings (includes #16, 18 & 43) . . . . . . . . . . . . .1 Primary Agitator, 200 gal., with Gallon Markings (includes #16, 18 & 43) . . . . . . . . . . . . .1 Primary Agitator, 250 gal., with Gallon Markings (includes #16, 18 & 43) . . . . . . . . . . . . .1 Primary Agitator, 40 gal., with Liter Markings (includes #16, 18 & 43) . . . . . . . . . . . . . . .1 Primary Agitator, 60 gal., with Liter Markings (includes #16, 18 & 43) . . . . . . . . . . . . . . .1 Primary Agitator, 80 gal., with Liter Markings (includes #16, 18 & 43) . . . . . . . . . . . . . . .1 Primary Agitator, 100 gal., with Liter Markings (includes #16, 18 & 43) . . . . . . . . . . . . . .1 Primary Agitator, 125 gal., with Liter Markings (includes #16, 18 & 43) . . . . . . . . . . . . . .1 Primary Agitator, 150 gal., with Liter Markings (includes #16, 18 & 43) . . . . . . . . . . . . . .1 Primary Agitator, 200 gal., with Liter Markings (includes #16, 18 & 43) . . . . . . . . . . . . . .1 Primary Agitator, 250 gal., with Liter Markings (includes #16, 18 & 43) . . . . . . . . . . . . . .1 Roller Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Hydraulic Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .specify length Bridge Swivel Housing Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 REMOTE CONTROL ASSEMBLY 1 For Standard Direct Steam Mixer Kettles NOTE: See SWITCH CONFIGURATIONS for applicable contact cartridge/capacitor combinations and part numbers 16 INCLUDED WITH ALL SWITCHES. 14 13 14 6 15 5 4 10 11 12 2 DI 7 Cl GI ev TA L W ela AT ER 17 nd ME TE R 8 18 9 ITEM NO. PART NO. DESCRIPTION 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. KE53479 KE53257 KE51857 KE53258 KE52710 KE52835 KE52936 KE51139 KE54402 KE01820 SK50370 KE54402 KE003209-6 KE003209-1 KE003209-7 KE52272 KE50753-9 Digital Temperature Controller and Indicator . . . . . . . . . . . . . . . . . . . . .1 Digital Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Front Cover, Digital Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Panel Mount Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Bracket for Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Holder, Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Mounting Bracket, Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Ambient Heater Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Mounting Bracket, Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Momentary Spring Return Switch Assembly . . . . . . . . . . . . . . . . . . . . .1 Switch Assembly, On/Off - Maintained . . . . . . . . . . . . . . . . . . . . . . . . . .2 Momentary Spring Return Switch Assembly . . . . . . . . . . . . . . . . . . . . .2 Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE95229 KE95229-1 Label: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 English French 18. QTY. REMOTE CONTROL ASSEMBLY For Cook Chill Direct Steam Mixer Kettles NOTE: See SWITCH CONFIGURATIONS for applicable contact cartridge/capacitor combinations and part numbers 12 15 2 3 INCLUDED WITH ALL SWITCHES. 16 7 8 9 5 10 11 17 6 9 1 4 5 6 ITEM NO. PART NO. DESCRIPTION 1. 2. 3. 4. 5. 6. 7. 8. KE53257 SE50354 SE50354 KE01820 SK50370 KE54402 KE003209-1 KE003209-3 9. 10. 11. 12. 12. 13. 14. 15. 16. 17. KE003209-1 KE003209-6 KE003209-7 KE53136-1 KE53136-2 KE53131 KE53132 FA11091 SK50315-1 Digital Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Pen Tip, red (pkg. of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Pen Tip, green (pkg. of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Ambient Heater Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Mounting Bracket, Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Switch Assembly, On/Off - Maintained . . . . . . . . . . . . . . . . . . . . . . . . . .1 Switch Assembly, On/Off/On - Maintained (single kettle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 (twin kettle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Switch Assembly, On/Off - Maintained . . . . . . . . . . . . . . . . . . . . . . . . . .2 Momentary Spring Return Switch Assembly . . . . . . . . . . . . . . . . . . . . .1 Momentary Spring Return Switch Assembly . . . . . . . . . . . . . . . . . . . . .2 Chart Recorder (TCR-DTCI) /Temperature Controller . . . . . . . . . . . . . .1 Chart Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Gasket, 24 1/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Gasket, 15 3/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Pilot Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Label: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 English French KE95438 KE95438-1 14 13 QTY. MAIN CONSOLE CONTROLS 2 For Standard Direct Steam Mixer Kettles 1 9 10 L I F T NOTE: See SWITCH CONFIGURATIONS for applicable contact cartridge/capacitor combinations and part numbers 11 12 13 O AT FF/A HE UT O CO OL 4 O AT FF/A HE 3 6 MI X UT O CO OF OL F INCLUDED WITH ALL SWITCHES. LI FT OF F 6 ON 5 UP 6 OF F DO W N 7 14 8 ITEM NO. PART NO. DESCRIPTION QTY. 1. KE52190 Knob, Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. KE00860 Cable and Bracket, Speed Control (includes items 9 - 13) . . . . . . . . . .1 3. KE53193 Emergency Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4. KE53377 Push Button Contact Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 5. SK50315-1 Pilot Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 6. KE003209-5 Switch Assembly, On/Off/On - Maintained (single kettle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 (twin kettle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 7. KE003209-1 Switch Assembly, On/Off - Maintained . . . . . . . . . . . . . . . . . . . . . . . . . .1 8. KE003209-7 Switch Assembly, On/Off/On - Momentary . . . . . . . . . . . . . . . . . . . . . . .1 9. KE52180 Micro Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 10. FA10032 Machine Screw, #4-40 x 5/8" LG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 12. FA32002 Tooth Lock Washer #4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 13. 14. FA20000 KE95230-E Hex Nut, #4-40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Label: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 MAIN CONSOLE CONTROLS 2 SP For Cook Chill Direct Steam Mixer Kettles EE D NOTE: See SWITCH CONFIGURATIONS for applicable contact cartridge/capacitor combinations and part numbers 1 6 7 CO 5 NT RO 8 L 4 6 7 9 10 9 3 FA ST 2 1 MI X M IX ER OF F INCLUDED WITH ALL SWITCHES. UN M LEOTO SS R M COWI IN NTLL . RONO L TS IS T ATAR LI FT "MT IN ." LI 11 UP EM ER STGE OPNC Y FT OF F DO W N 5 4 3 12 ITEM NO. PART NO. DESCRIPTION QTY. 1. KE52190 Knob, Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. KE00860 Cable and Bracket, Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. KE53193 Emergency Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4. KE53377 Push Button Contact Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 5. KE003209-8 Switch Assembly, On/Off/On - Momentary . . . . . . . . . . . . . . . . . . . . . . .1 6. KE52180 Micro Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 7. FA10032 Machine Screw, #4-40 x 5/8" LG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 9. FA32002 Tooth Lock Washer, #4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 10. FA20000 Hex Nut, #4-40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 11. KE003209-5 Switch Assembly, On/Off/On - Maintained . . . . . . . . . . . . . . . . . . . . . .1 12. KE95230-E Label: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 SWITCH CONFIGURATION SPEED CONTROL 5 4 6 L IF 3 7 8 INDEX Capacitor T For Standard Direct Steam Mixer Kettles 2 1 9 Contactor Cartridges * FAST MIN. MOTOR WILL NOT START UNLESS CONTROL IS AT "MIN." LEFT KETTLE OFF/AUTO HEAT COOL EMERGENCY STOP RIGHT KETTLE OFF/AUTO HEAT COOL PART NO. LIFT OFF MIX OFF LIFT UP DOWN EMPTY EMPTY NOTES: *For units built prior to December 2006, the complete switch assembly must be ordered (see applicable drawing). MIXER ON EMPTY OFF EMPTY MAIN POWER KE603208-9 KE603208-8 EMPTY KE52074 Refer to Maintenance Section for Switch Disassembly Instructions. CONTROLLER START ON EMPTY EMPTY EMPTY EMPTY EMPTY EMPTY INTERRUPT OFF EMPTY CONTINUE RESET ACTIVE EMPTY EMPTY EMPTY BYPASSED KE95230-C POWER DIGITAL WATER METER OPERATING INSTRUCTIONS DISCONNECT FROM POWER SUPPLY BEFORE SERVICING 1. Turn POWER switch ON. 2. Set required volume. Do not exceed kettle capacity. 3. Locate delivery spout over desired kettle. 4. Press START switch downward to RESET. Delivery will start at “0” and stop at preset volume. 5. To stop delivery any time, press INTERRUPT switch downward. 6. To complete delivery after interrupting, press START switch upward to CONTINUE. 7. Turn POWER switch to OFF when meter is not in use. KE95229-G SWITCH CONFIGURATION SPEED CONTROL For Cook Chill Direct Steam Mixer Kettles 5 4 6 IF 8 T 3 7 INDEX L 2 1 9 Capacitor Contactor Cartridges FAST MIN. MOTOR WILL NOT START UNLESS CONTROL IS AT "MIN." MIXER LIFT OFF OFF UP DOWN EMPTY LIFT EMPTY MIX PART NO. KE52074 KE603208-9 KE603208-8 EMERGENCY STOP NOTES: *For units built prior to December 2006, the complete switch assembly must be ordered (see applicable drawing). Refer to Maintenance Section for Switch Disassembly Instructions. OFF General Operation ON BYPASS ACTIVE 1. Turn MAIN POWER SWITCH to "ON". OFF HEAT AUTO COOL Lifting & Lowering Bridge OFF MIX LIFT 5 6 4 L 2. Turn MIXER SPEED CONTROL to "MIN" and adjust to desired speed. IF T 3 7 2 MIN. OFF UP DOWN 3. Turn and hold UP/DOWN SWITCH "UP" to raise or "DOWN" to lower. WARNING- Insure FAUCET SPOUT is out of way before raising or lowering bridge. OFF MIX LIFT Mixing Manual Heating/ Cooling 1. Turn ACTIVE/BYPASS SWITCH to "BYPASS". OFF HEAT AUTO COOL BYPASS ACTIVE Automatic Heating/ Cooling NOTE: TEMPERATURE PROBE on MIXER BRIDGE must be covered ith i i f th i h f OFF ON Water Meter Discharge Valve EMPTY EMPTY EMPTY EMPTY EMPTY EMPTY EMPTY EMPTY START OFF ON For cool: open STEAM VALVE completely. 1 FAST BYPASS ACTIVE START CONTINUE RESET 2. Turn CONTROLLER SWITCH to "HEAT" or "COOL". 3. For heat: open STEAM VALVE completely to boil, or adjust to regulate temperature. 1. Turn MIX/LIFT SWITCH to "LIFT". SPEED CONTROL 8 9 WATER METER INTERRUPT EMPTY ON OFF HEAT AUTO COOL EMPTY EMPTY EMPTY OFF CONTROLLER OFF HEAT AUTO COOL EMPTY MAIN POWER KE95230-C ELECTRICAL COMPONENT ASSEMBLY 1 2 9 For Standard Direct Steam Mixer Kettles THERMAL OVERLOAD RELAY 24 8 15 19 7 17 19 21 12 18 20 ITEM NO. 13 5 4 16 6 10 11 15 19 PART NO. DESCRIPTION 1. 2. 4. 5. 6. 7. 8. KE50343-7 KE50753-10 KE51139 SK50445 KE52936 KE50750-1 KE51982 Component Mounting Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7 Fuse Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Fuse (3 amps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Fuse (1 amps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Contactor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Thermal Overload Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE52055 KE52051 Heater for Thermal Overload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 200, 208, 220, 240, 380 & 415 volt 440, 480 volt SK50055-1 SK50054-1 Terminal Block Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6 Terminal Block End Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE53838-5 KE53838-6 Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 200, 208, 220, 240, 440 & 480 volt 380 & 415 volt FA10133 FA10239 FA12500 FA10245 FA10362 FA32005 FA32006 KE02274 Screws #6-32x3/8" lg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Screws #8-32x3/8" lg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Screws #8-32x3/8" lg. (brass with undercut) . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Screws #8-32x1" lg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Screws #10-32x3/8" lg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Lockwashers #8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Lockwashers #10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Capacitor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 9. 10. 11. 12. 13. 15. 16. 17. 18. 19. 20. 21. QTY. ELECTRICAL COMPONENT ASSEMBLY 1 2 3 15 21 24 21 11 For Cook Chill Direct Steam Mixer Kettles THERMAL OVERLOAD RELAY MAIN TERMINAL BLOCK 24 10 17 22 8 7 9 19 22 25 15 6 14 20 23 18 4 22 17 13 12 ITEM NO. PART NO. DESCRIPTION 1. 2. 3. 4. 6. 7. 8. 9. 10. KE50343-8 KE52710 KE52835 KE50753-10 KE51139 SK50445 KE52936 KE50750-1 KE51982 Component Mounting Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Bracket for Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-9 Fuse Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Fuse (3 amps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Fuse (1 amps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Contactor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Thermal Overload Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE52055 KE52051 Heater for Thermal Overload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 200, 208, 220, 240, 380 & 415 volt 440, 480 volt SK50055-1 SK50054-1 Terminal Block Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Terminal Block End Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE53838-5 KE53838-6 Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 200, 208, 220, 240, 440 & 480 volt 380 & 415 volt FA10133 FA10135 FA10239 FA12500 FA10245 FA10362 FA32004 FA32005 FA32006 FA20002 KE02274 Screws #6-32x3/8" lg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Screws #6-32x1/2" lg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-11 Screws #8-32x3/8" lg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Screws #8-32x3/8" lg. (brass with undercut) . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Screws #8-32x1" lg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Screws #10-32x3/8" lg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Lockwashers #6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Lockwashers #8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Lockwashers #10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Hex Nut #6-32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Capacitor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. QTY. PLUMBING ASSEMBLY 10" CONSOLE ITEM NO. PART NO. DESCRIPTION 1. KE02055-2 KE02055-4 FI00267 FI00629-31 FI00179 FI00629-36 FI00152 KE51653 KE51367 KE54834-3 SE50405 SE50406 KE54834-4 SE50410 SE50404 KE54834-8 SE50409 SE50404 FI00629-30 FI00063 KE51654 KE53008 FI00629-29 FI0062919 KE54834-5 SE50407 SE50401 KE54834-4 SE50410 SE50404 FI00629-4 FI00629-7 Steam Valve 3/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Steam Valve 1 1/4" Coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Nipple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Tee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Nipple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Street Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Check Valve 3/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Check Valve 1 1/4" * Solenoid Valve, 3/4" - 50 psi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Rebuild Kit Replacement Coil * Solenoid Valve, 3/4" - 100 psi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Rebuild Kit Replacement Coil * Solenoid Valve, 1 1/4" - 100 psi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Rebuild Kit Replacement Coil Nipple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Y-Strainer 3/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Y-Strainer 1 1/4" Nipple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Nipple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 * Solenoid Valve, 3/4" - 50 psi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Rebuild Kit Replacement Coil * Solenoid Valve, 3/4" - 100 psi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Rebuild Kit Replacement Coil Nipple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Nipple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. . 12. 13. 14. 15. 16. *NOTE: See SOLENOID VALVE MAINTENANCE section for further information. 100 gallons and up use the larger valves. QTY. PLUMBING ASSEMBLY - 18" CONSOLE ITEM NO. PART NO. DESCRIPTION 1. FI00096 Union . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. F100179 Tee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. F105130 Reducing Nipple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4. KE52702 Y-Strainer, 1/2" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 5. KE52701 Steam Trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 6. FI00151 Street Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 7. FI00441 Reducing Bushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 8. FI00363 Reducing Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 9. KE54834-5 * Solenoid Valve, 3/4" - 50 psi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 SE50407 SE50401 KE54834-4 QTY. Rebuild Kit Replacement Coil * Solenoid Valve, 3/4" - 100 psi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 SE50410 Rebuild Kit SE50404 Replacement Coil 10. FI00143 Street Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 11. KE51653 Check Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 12. KE51654 Y-Stainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 13. KE52666 Thermostat Mtg. Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 14. UR50077 Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 15. FA11052 Bindinghead Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 16. FA11060 Bindinghead Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 17. FI00178 Tee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 18. FI05089 Reducing Nipple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 19. KE54834-2 SE50408 SE50404 * Solenoid Valve, 3/8" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Rebuild Kit Replacement Coil *NOTE: See SOLENOID VALVE MAINTENANCE section for further information. MANUAL TILT - 10" CONSOLE ITEM NO. PART NO. DESCRIPTION QTY. 1. KE51730 Tilt Shaft Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. KE50375 Tilt Shaft, Small Gear, 40 to 80 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE503751 Tilt Shaft, Small Gear, 100 gal. and up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. FA19505 Handwheel Allen Screw, Hex Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4. KE00508 Handwheel Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 5. FA95007-1 Retaining Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 6. FA05002-6 "O" Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 7. FA95048 Woodruff Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 8. FA19201 Set Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 9. 10. KE00151 Segment Gear, Small, up to 60 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE52833 Segment Gear, Large, 80 gal. and up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE00699 Trunnion Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 11. FA19177 Hex-Socket Set Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 12. FA20047 Jam Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 13. KE52191 Roller Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 14. KE52193 Thrust Bearing Spacer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 15. KE50315 Worm Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 16. FA95005 Tension Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 17. FA95008 Hex Nut 3/4-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 18. FA30088 Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 19. KE52192 Thrust Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 POWER TILT - 10"/12" CONSOLE POWER TILT - 10"/12" CONSOLE ITEM NO. PART NO. DESCRIPTION QTY. 1. KE50581 Bridge Rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. KE51007 Micro Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 3. KE52192 Thrust Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 4. KE52193 Thrust Bearing Spacer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 5. KE52191 Roller Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 6. FA30088 Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 8. FA95008 Hex Nut, 3/4-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 9. SE00028 Knob Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 11. KE50315 Worm Gear, 12. FA95005 Tension Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 13. KE51730 Tilt Shaft Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 14. KE00151 Segment Gear, Small, up to 60 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE52833 Segment Gear, Large, 80 gal. and up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE00699 Trunnion Housing, 40 to 80 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE001182 Trunnion Housing, 100 gal. and up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 16. FA95007-1 Retaining Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 17. FA05002-6 "O" Ring (40-80 gal.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 (per kettle) FA05002-27 "O" Ring (40-80 gal.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 (per kettle) 18. FA95048 Woodruff Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 19. FA19201 Set Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 20. FA19177 Hex-Socket Set Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 21. FA20047 Jam Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 22. KE50582 Coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 23. KE50583 Coupling Insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 25. KE52832-1 Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 26. SK50055-1 Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 27. SK50054-1 Terminal Block End-Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 28. 29. KE50579-1 Circuit Breaker. 1.3 Amp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 FA05002-34 "O" Ring, Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE50580 Water Resistant Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE003209-11 Complete Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE603208-4 KE603208-7 KE603208-9 Momentary Switch Activator*** . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Contact Section Holder, Latch*** . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Contact Block*** . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ***NOTE: for units built prior to Dec. 2006 order Complete Switch KE003209-11 WATER METER ASSEMBLY 18" CONSOLE WATER METER ASSEMBLY 18" CONSOLE ITEM NO. PART NO. 1. FI05058 3/4" Cross . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. KE02055-2 Steam Valve Modification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 3. N0640B4.5 Nipple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 4. FI00063 Elbow 90 degree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 5. FI000356 Reducing Bushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 6. KE600812-1 Street Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 7. FI05029 Hose Barb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 KE54834-5 * Solenoid Valve, 3/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 8. 9. 10. 11. DESCRIPTION SE50407 Rebuild Kit SE50401 Replacement Coil QTY. N0640B3 Nipple, Gallon Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N0640B3.5 Nipple, Litre Meter FI00363-3 Reducing Elbow 90 Degree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE51861 Gallon Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE51860 Litre Meter 12. FI00062 Elbow 90 Degree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 13. KE52173 1/2"1.D. Hot Water Wash-up Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 14. FI05220-3 Hose Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 15. FI00179 Tee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 16. FI05074 Adapter, Gallon Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 KE600362 Adapter, Litre Meter 17. N0640B1.5 Nipple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 18. FA11091 Machine Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 20. KE51369 Steam Valve Flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 21. SE00028 Knob Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 22. KE95321 Label "Hot" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 23. KE95322 Label "Cold" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 24. SD50097 Flanged Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 25. KE51585 Faucet Spout Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 26. KE50825-12 Faucet Spout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 27. FA05002-19 "O" Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 28. FA95022 Retaining Ring Carter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 29. KE51736 Long Faucet Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 *NOTE: See SOLENOID VALVE MAINTENANCE section for further information. FLUSH PISTON VALVE (USED PRIOR TO 2003) ITEM NO. PART NO. DESCRIPTION QTY. T40430 Valve Assembly (includes parts 1 - 16) . . . . . . . . . . . . . . . . . . . . . . . . .1 1. FA05000 "O" Ring, Cylinder Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. KE52345 Piston Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. KE52346 Air seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4. KE52347 Sani-Clamp Seal, 4” 5. KE52344 Sani-Clamp, 4” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 6. FA05002-22 "O" Ring, Cylinder Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 7. FA05002-21 "O" Ring, Piston . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 8. KE52315 Piston . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 9. 10.-13. KE52335 SE00040 Compression Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Supply Hose Assembly, Piston . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 10. KE52341 Hose Barb, 1/8” x 1/4” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 11. KE52340 Supply Hose, 8” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 12. KE52342 Hose Barb, 1/4” x 1/4” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 13. KE52338 Quick Connect Male End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 14. KE52327 Piston Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 15. KE52328 Piston Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 16. KE52314 Bottom Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 FLUSH PISTON AIR SYSTEM, 10" CONSOLE (USED PRIOR TO 2003) ITEM NO. PART NO. DESCRIPTION QTY. 1. FA30512 Spacer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. FA32500 Tooth lockwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. KE52697 Locking nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4. KE52931 Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 5. FI00266 Coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 6. FI00595-17 Nipple 1/2" NPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 7. FI00178 Tee 1/2" NPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 8. FI00595-12 Nipple 1/2" NPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 9. FI05047 Bushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 10. KE52342 Hose Barb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 11. FI05167 Hose Barb 90 Degree Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 12. KE52815 Airline Lubricator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 13. KE52895 Air Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 14. KE52339 Female End Quick Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 15. KE52932 Bracket For Lubricator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 16. FA32006 Toothlock Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 17. FA21006 Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 18. FA11091 Machine Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 19. KE53209 Quick Exhaust Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 20. KE53210 Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 21. KE52031 Air Line Filter c/w Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 22. KE53251 Air Line Filter Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 23. FA11144 Bindinghead Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 24. FI05166 Quick connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 25. KE54280 Slide valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 26. KE53215 1/4" Air Hose, 65" Long . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 FLUSH PISTON LUBRICATOR (USED PRIOR TO 2003) ITEM NO. PART NO. DESCRIPTION QTY. 1. FA30512 Spacer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 1.-5 KE52815 Lubricator c/w Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 1. SE50418 Sight Dome Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. SE50419 Filler Cap Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. SE50420 Needle Valve Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4. SE50422 "O" Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 5. SE50423 Bowl/Guard Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 FLUSH PISTON FILTER (USED PRIOR TO 2003) ITEM NO. PART NO. DESCRIPTION QTY. 1.-5 KE52031 Filter c/w Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 1. SE50425 Deflector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. SE50426 Filter Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. SE50427 Baffle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4. SE50428 "O" Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 5. SE50429 Bowl/Guard Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 FLUSH PISTON VALVE (USED AFTER TO 2003) 12 13 4 12 AIR VALVE ASSEMBLY FPVA-3 1 5 2 6 3 7 8 9 10 8 11 ITEM ON. PART NO. DESCRIPTION QTY. 1. KE55210 WELD RING, KETTLE BOTTOM OUTLET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. FI05144-3 SANI CLAMP, 3” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3. KE52154-4 GASKET, SANI CLAMP, 3” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4. KE02291 COMPLETE ACTUATOR AND DISCHARGE VALVE ASSEMBLY . . . . . . . . . . . . 1 INCLUDES PARTS 5. - 13. 5. KE55248 BUNA-N O-RING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 6. KE55249 REPLACEABLE S.S. PLUNGER HEAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 7. KE55250 BUNA-N O-RING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 8. KE55251 1/8 NPT S.S. HYDRAULIC CLOSE NIPPLE . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 9. KE55252 MALE S.S. QUICK DISCONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 10. KE55253 AIR OPERATED CYLINDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 11. KE55254 FEMALE S.S. QUICK DISCONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 12. KE55255 BUNA-N O-RING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 13. KE55256 BODY, DISCHARGE VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 FLUSH PISTON AIR SYSTEM, 10" CONSOLE (USED AFTER TO 2003) N1 N2 ITEM NO. PART NO. DESCRIPTION QTY. I KE601603 QUICK CONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I 2 KE601601 SLIDE VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3 FA30512 SPACER WASHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i 4 FA32500 TOOTH LOCK WASHER 7/8 DIA, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 5 KE52697 NUT 1/2 NIPS BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .~~ 6 KE601602 AIR FITTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I 7 KE600814-1 TEE 1/2 NPT (FIP x FIP x FIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I 8 FI00351 BUSHING 1/2 MIP x 1/4 FIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 9 FI05318 HOSE BARB 90' ELBOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 11 FA30090 WASHER 15/16 IDxl 3/4 ODxl/8 THK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 13 KE02369 FILTER-REGULATOR ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 14 FI05220-1 GEAR CLAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 15 FA21002 #6-32 HEX NUT SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 16 KE532176 PNEUMATIC HOSE (1/4 I.D.xl2 1/2 LG.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 FLUSH PISTON AIR SYSTEM, 10" CONSOLE (USED AFTER TO 2003) 17 KE532177 PNEUMATIC HOSE, (1/4 I.D.x 31 LG.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 18 FA32004 TOOTH LOCK WASHER, #6 ZINC PLATED . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 19 SEE FOLLOWING PAGE: FLUSH PISTON - AIR SOLENOID VALVE (Used after to 2003) 20 KE50555-3 GROMMET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 21 KE01812-1 SWITCH ON/OFF/ON (MAINT/MAINT/MOM) . . . . . . . . . . . . . . . . . . . . . . . . . . .1 24 KE95481-5 LABEL, PRODUCT DISCHARGE VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 25 KE55232 WIRING DIAGRAM FOR AIR VALVE (NOT SHOWN) . . . . . . . . . . . . . . . . . . . . .1 POWER TILT OPTION 30 KE02185 COMPONENT PLATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 32 FA21007 #10-32 HEX NUT SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 33 FA40000-6 TOOTH LOCK WASHER, #10 ZINC PLATED . . . . . . . . . . . . . . . . . . . . . . . . . . .2 N1 FI00595-17 NIPPLE, 1/2 NPT x 11 1/8 LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N2 FI0059 5-12 NIPPLE, 1/2 NPT x 10 1/2LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N1 FI00595-17 NIPPLE, 1/2 NPT x 11 1/8 LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N2 FI00595-13 NIPPLE, 1/2 NPT x B 7/8 LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N1 FI00595-17 NIPPLE, 1/2 NPT x 11 1/8 LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N2 FI00595-14 NIPPLE, 1/2 NPT x 8 1/2 LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N1 FI00595-12 NIPPLE, 1/2 NPT x 10 1/2 LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N2 FI00595-15 NIPPLE, 1/2 NPT x 6 7/8 LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N1 FI00595-19 NIPPLE, 1/2 NPT x 13 7/8 LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N2 FI00595-16 NIPPLE, 1/2 NPT x 7 5/8 LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N1 FI00595-12 NIPPLE, 1/2 NPT x 10 1/2 LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N2 FI00595-7 NIPPLE, 1/2 NPT x 4 LG.BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N1 FI00595-19 NIPPLE, 1/2 NPT x 13 7/8 LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N2 FI00595-11 NIPPLE, 1/2 NPT x 6 LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N1 FI00595-19 NIPPLE, 1/2 NPT x 13 7/8 LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 N2 FI00595-7 NIPPLE, 1/2 NPT x 4 LG. BRASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 NIPPLES for MKDL-40CC for MKDL-60CC for MKDL-80CC for MKDL-100CC for MKDL-125CC for MKDL-150CC for MKDL-200CC for MKDL-250CC FLUSH PISTON AIR SOLENOID VALVE (USED AFTER TO 2003) ITEM ON. PART NO. DESCRIPTION QTY. 5. KE55257 MALE QUICK PLUG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 6. FI05317-1 HOSE BARB, 1/8' NPT MALE TO 1/4” HOSE . . . . . . . . . . . . . . . . . . . . . . . . . . .2 7. KE55259-1 1/4” ID X 6 FT LONG HOSE, 250 #W,P. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 8. FI05317-2 HOSE BARB, 1/4” NPT MALE TO 1/4” HOSE . . . . . . . . . . . . . . . . . . . . . . . . . . .2 9. KE55261-1 EXHAUST MUFFLER, 1/8” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 10 KE55262 FEMALE QUICK PLUG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 11. KE55263-1 5 WAY AIR SOLENOID VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 12. KE55264-1 STANDARD 1/8” MUFFLER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 13. FI05220-1 GEAR CLAMP FOR 1/4” I,D, HOSE (NOT SHOWN) . . . . . . . . . . . . . . . . . . . . . .5 14. FI05030-2 90° 1/4” ELBOW, MALE PIPE THREAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 15. KE55305 1/4” FLOW CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 16. KE55259-2 /4” ID X 3 FT LONG HOSE, 250 #W,P. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 17. FI05318 90° ELBOW HOSE BARB/ 1/4” HOSE I,D./14” PIPE, BRASS . . . . . . . . . . . . . . .1 BUTTERFLY VALVE 1 3 4 5 6 7 2 ITEM NO. PART NO. DESCRIPTION 1. - 7. KE51603 Butterfly Valve, 2" (includes housing) . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE52286 Butterfly Valve, 3" (includes housing) . . . . . . . . . . . . . . . . . . . . . . . . . . .1 1. FA11224 Bolt, 5/16-18 x1" S.S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2. FA21024 Nut, 5/16-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 3. SE50433 Seat, 2" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 SE50433-1 Seat, 3" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 SE50434 Stem, 2" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 SE50434-1 Stem, 3" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 SE50435 Locking Spider, 2" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 SE50435-1 Locking Spider, 3" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 6. SE50436 Handle Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 7. SE50437 Allen Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4. 5. QTY. Rev 1 MAIN COMPONENT REFERENCE CHARTS Valves: KETTLE SIZE PRESSURE STEAM TRAP SAFETY VALVE MANUAL VALVE CHECK VALVE GALLONS PSI 40 50 1/2" NPT KE51248 3/4" x 3/4" KE51720 3/4" x 3/4" KE02055-2 3/4" KE51653 60-80 50 1/2" NPT KE51248 3/4" x 3/4" KE51720 3/4" x 3/4" KE02055-2 100-125 35 1/2" NPT KE51248 1-1/4" x 1-1/4" KE53144 150 35 1/2" NPT KE51248 200-250 35 40 SOLENOIDS STRAINER STEAM CONDENSATE POTABLE WATER COOLING WATER DUMP VALVE 3/4" KE51654 3/4" x 3/4" KE54834-3 3/4" x 3/4" KE54834-5 3/4" x 3/4" KE54834-5 3/4" x 3/4" KE54834-5 3/8" x 3/8" KE54834-2 3/4" KE51653 3/4" KE61654 3/4" x 3/4" KE54834-3 3/4" x 3/4" KE54834-5 3/4" x 3/4" KE54834-5 3/4" x 3/4"" KE54834-5 3/8" x 3/8" KE54834-2 1-1/4" x 1-1/4" KE02055-4 1-1/4" KE51367 1-1/4" KE53008 1-1/4" x 1-1/4" KE54834-8 3/4" x 3/4" KE54834-5 3/4" x 3/4" KE54834-5 3/4" x 3/4"" KE54834-5 3/8" x 3/8" KE54834-2 1-1/4" x 1-1/4" KE53144 1-1/4" x 1-1/4" KE02055-4 1-1/4" KE51367 1-1/4" KE53008 1-1/4" x 1-1/4" KE54834-8 3/4" x 3/4" KE54834-5 3/4" x 3/4" KE54834-5 3/4" x 3/4"" KE54834-5 3/8" x 3/8" KE54834-2 1/2" NPT KE51248 1-1/4" x 1-1/4" KE53144 1-1/4" x 1-1/4" KE02055-4 1-1/4" KE51367 1-1/4" KE53008 1-1/4" x 1-1/4" KE54834-8 3/4" x 3/4" KE54834-5 3/4" x 3/4" KE54834-5 3/4" x 3/4"" KE54834-5 3/8" x 3/8" KE54834-2 100 1/2" NPT KE53160 3/4" x 1" KE53158 3/4" x 3/4" KE02055-2 3/4" KE51653 3/4" KE61654 3/4" x 3/4" KE54834-4 3/4" x 3/4" KE54834-4 3/4" x 3/4" KE54834-5 3/4" x 3/4"" KE54834-4 3/8" x 3/8" KE54834-2 60-80 100 1/2" NPT KE53160 3/4" x 1" KE53158 3/4" x 3/4" KE02055-2 3/4" KE51653 3/4" KE61654V 3/4" x 3/4" KE54834-4 3/4" x 3/4" KE54834-4 3/4" x 3/4" KE54834-5 3/4" x 3/4"" KE54834-4 3/8" x 3/8" KE54834-2 100-125 100 1/2" NPT KE53160 1-1/4" x 1-1/4" KE53162 1-1/4" x 1-1/4" KE02055-4 1-1/4" KE51367 1-1/4" KE53008 1-1/4" x 1-1/4" KE54834-8 1-1/4" x 1-1/4" KE54834-8 3/4" x 3/4" KE54834-5 3/4" x 3/4"" KE54834-5 3/8" x 3/8" KE54834-2 150 100 1/2" NPT KE53160 1-1/4" x 1-1/4" KE53162 1-1/4" x 1-1/4" KE02055-4 1-1/4" KE51367 1-1/4" KE53008 1-1/4" x 1-1/4" KE54834-8 1-1/4" x 1-1/4" KE54834-8 3/4" x 3/4" 1-1/4" x 1-1/4"" KE54834-5 KE54834-8 3/8" x 3/8" KE54834-2 200-250 100 1/2" NPT KE53160 1-1/4" x 1-1/4" KE53162 1-1/4" x 1-1/4" KE02055-4 1-1/4"" KE51367 1-1/4" KE53008 1-1/4" x 1-1/4" KE54834-8 1-1/4" x 1-1/4" KE54834-8 3/4" x 3/4" 1-1/4" x 1-1/4"" KE54834-5 KE54834-8 3/8" x 3/8" KE54834-2 Mechanical: Scraper Blades: KETTLE SIZE PRESSURE GALLONS PSI STANDARD PRIMARY SECONDARY 40 50 KE00151 (SMALL) MANUAL KE51846 KE51845 10 40 18 60-80 50 KE00151 (SMALL) MANUAL KE51938 KE51845 18 100-125 35 KE52833 (BIG) MANUAL KE51938 KE51845 10 60 12 18 150 35 KE52833 (BIG) POWER KE51938 KE51845 80 12 18 GEAR SIZE TILT HYDRAULIC MOTORS GEAR SIDE KETTLE CONSOLE SIZE GALLONS CENTRE CONSOLE QUANTITY 22 26 30 200-250 35 KE52833 (BIG) POWER KE53004 KE53005 12 100 20 34 40 100 KE00151 (SMALL) MANUAL KE51846 KE51845 10 125 18 60-80 100 KE00151 (SMALL) MANUAL KE51938 KE51845 18 120-125 100 KE52833 (BIG) MANUAL KE51938 KE51845 10 150 12 18 150 100 KE52833 (BIG) POWER KE51938 KE51845 200 12 18 200-250 100 KE52833 (BIG) POWER KE53004 KE53005 250 12 20 48 38 38 44 MAINTENANCE INSPECTION AND MAINTENANCE CHECK LIST Cleveland Range equipment requires little preventative maintenance. We do however provide the following chart as a guide line for inspection and maintenance to keep your unit functioning at 100%. MONTHLY INSPECTIONS Item Inspection Item Switches Inspect switches for damage and correct operation. Replace as required. Product Drain Valves Tangent Draw-Off Valve Inspect parts for damage. Test valve for leakage. Replace as required. Butterfly Valve. Inspect parts for damage. Test valve for leakage. Replace as required. Air Valve Inspect parts for damage. Test valve for leakage. Check valve seals for air leakage. Inspect supply hose and fittings. Replace as required. Inspect air filter and replace if required. SIX MONTH MAINTENANCE Lubrication Grease trunnion housings. Grease bridge swivel assembly. Use "Never Seize" on tilt worm and gear. Strainers Clean strainers in steam in and cooling water supply lines. YEARLY MAINTENANCE Lubrication Drain hydraulic oil and remove filter. Replace oil and filter (see Hydraulic Oil Replacement Procedure. Solenoid Valves Inspect solenoid valves for proper operation. Clean or replace as required. WARRANTY Our Company supports a worldwide network of Maintenance and Repair Centers. Contact your nearest Maintenance and Repair Centre for replacement parts, service, or information regarding the proper maintenance and repair of your cooking equipment In order to preserve the various agency safety certification (UL, NSF, ASME/Ntl. Bd., etc.), only factorysupplied replacement parts should be used. The use of other than factory supplied replacement parts will void warranty. AIR LINE LUBRICATOR OIL FILLING PROCEDURE AUTOMATIC DUMP VALVE Replacing “O” rings (8): 1. Disconnect air supply and bleed system. 2. Remove cover on console (see PARTS LIST PNEUMATIC COMPONENTS). 3. Check for oiler location. Filler Cap 3 4. Inspect oil level in bowl. 5 5. Remove filler cap. 2 4 8 6. Add mineral oil as required. Bowl 7. Replace filler cap and console cover. 7 1 6 Oiler Automatic Dump Valve AIR FILTER REPLACEMENT PROCEDURE 1. Disassemble valve as per daily cleaning instructions. 1. Disconnect air supply and bleed system. 2. Holding lower valve body (6), unscrew valve bottom (7). 2. Remove cover on console (see Parts List Pneumatic Components). 3. Pull lower valve body out from cylinder body. 3. Check for filter location. 4. Push lever down and rotate bowl/ guard assembly 1/8 turn. Deflector Filter Element Baffle Lever Bowl/Guard Assembly Air Filter 5. Push down on bowl/guard assembly and remove. 6. Unscrew baffle and remove filter element, inspect and replace filter if required. 7. Replace filler cap and cover. 4. Replace "O" rings (8), as required. 5. Coat cylinder body and "O" rings with cooking oil or food-safe grease. 6. Reassemble. STEAM TRAP Each kettle is equipped with a steam trap in the line of the kettle outlet to the drain, to remove line condensate that forms inside the steam jacket. A good steam trap at startup releases air and wet steam into the drain line for a few minutes, then holds the steam jacket. During cooking, the trap periodically releases accumulated condensate. If the kettle's cooking performance becomes inadequate after long use, replacement of the steam trap with a new one may restore kettle operation to peak efficiency. RE-INSTALLING SPEED CONTROL CABLE HYDRAULIC OIL REPLACEMENT PROCEDURE One of the most important maintenance tasks is to change the hydraulic oil yearly. Under heavy usage the oil should be changed every nine months. It is important to change the oil regularly to prevent its breakdown which leads to the damaging of components. The oil filter should be changed at the same time as the hydraulic oil. A clean filter prevents particles from damaging the other components in the system. Replace the hydraulic fluid as follows: A B ⇒ Disconnect power to unit. ⇒ Remover the front top panel on the main console. ⇒ Remove chrome vent cap from breather pipe located beside electric motor. ⇒ Remove plug bolt from bottom left front corner of main console to drain oil into your catch pail. ⇒ Remove oil filter. ⇒ Replace plug bolt. ⇒ Refill unit through breather pipe using approximately 12 U.S. gallons of Tellus 32 hydraulic oil (oil should be 6 1/2" deep in tank). ⇒ Install new oil filter (Part# SE50094). ⇒ Replace chrome vent cap and front top panel. ⇒ Reconnect power to unit. ⇒ Run unit to remove any air in the lines. G C D F E Speed Control Assembly 1. Turn sprocket of speed control so that wire."A" is fully extended towards shaft "B". 2. Insert end of cable through bracket "C". 3. Insert wire so it protrudes approximately 1/2" to 5/8" through hole in bolt "D". Tighten bolt and bend end of wire. 4. Bring pump arm "E" up until it hits stop bolt "F" and tighten screw "C". 5. Reassemble unit. Speed control knob will go on pointing toward minimum setting. 6. Turn mixer on with speed control set at minimum setting. 7. If scraper arm is turning, loosen nut "G" and back stop bolt "F" off a few turns. Next loosen screw "C" and slowly pull up cable until scraper arm stops turning. Retighten screw "C". Gently turn stop bolt "F" down until it hits arm. Lock in place by tightening nut "G". 8. Scraper arm should now go from no rotation to fast rotation by turning speed control knob. NOTE: Mixer may run rough and noisy for one or two hours if air has become trapped in the line. NOTE: Mixer may run rough and noisy for one or two hours if air has become trapped in the line. LUBRICATION Lubricate the following parts every three months to insure smooth operation and reduce wear. DISASSEMBLY OF SWITCH ASSEMBLY 1. Place slotted screwdriver between contactor cartridge and cartridge mounting block as shown in Fig.1. MIXER BRIDGE HOUSING Front Cover Back Cover Grease Nipples There are two grease nipples on the mixer bridge swivel housing which are accessed by removing the front and back covers on the 18" console. Fig. 1 Contactor cartridges Fig. 2 3. Place screwdriver under tab in the back of the cartridge mounting block as shown in Fig. 3. Side View of 18" Console Fig. 3 TRUNNION HOUSING, WORM SCREW AND TILT GEAR Adjusting Screw Worm Screw and Tilt Gear Cross Bar These parts are accessed through the front cover on the 18" console. Trunnion and Tilt Mechanism Drawing Apply grease to gear teeth. Check for excessive play and adjust with adjusting screw located on top of cross bar. Trunnion Housing Grease Nipple KETTLE TRUNNIONS Accessed via the top covers on the 10" and 18" consoles. Each has two grease nipples. Kettle Trunnion Drawing 2. Twist screwdriver to free cartridge. 4. Twist screwdriver to remove block from the rotary switch. Fig. 4 Cartridge Locking mounting block ring Rotary switch Switch Assembly 3. Unscrew locking ring to remove rotary switch. SOLENOID VALVE MAINTENANCE NOTE: It is not necessary to remove the valve from the pipeline for repairs. WARNING: Turn off electrical power supply and depressurize valve before making repairs. Cleaning All solenoid valves should be cleaned periodically. The time between cleanings will vary depending on the medium and service conditions. In general, if the voltage to the coil is correct, sluggish valve operation, excessive noise or leakage will indicate that cleaning is required . Clean valve strainer or filter when cleaning the valve. Preventive Maintenance 1. Keep the medium flowing through the valve as free from dirt and foreign material as possible. 2. While in service, the valve should be operated at least once a month to insure proper opening and closing. 3. Depending on the medium and service conditions, periodic inspection of internal valve parts for damage or excessive wear is recommended. Thoroughly clean all parts. Replace worn or damaged parts. However, for best results, replace all parts as supplied with a Rebuild Kit. Causes of Improper Operation 1. Faulty Control Circuits: Check the electrical system by energizing the solenoid. A metallic "click" signifies that the solenoid is operating. Absence of the "click" indicates loss of power supply . Check for loose or blown fuses, open circuited or grounded coil, broken lead wires or splice connections. Solenoid Valve Exploded View Drawing Ordering Information Parts marked with an asterisk (*) in the Solenoid Valve Exploded View Drawing are supplied in the Rebuild Kits. Valve # (Description) Rebuild Kit # Replacement Coil# KE54834-9 (2", 120V/60 Hz.) KE54834-6 (1", 120V/60 Hz.) KE54834-7 (1", 120V/60 Hz.) KE54834-3 (3/4", 120V/60 Hz.) KE54834-5 (3/4", 120V/60 Hz., HW) KE54834-2 (3/8", 120V/60 Hz.) KE54834-8 (1 1/4", 120V/60 Hz.) KE54834-4 (3/4", 120V/60 Hz.) SE50400 SE50402 SE50403 SE50405 SE50407 SE50408 SE50409 SE50410 SE50401 SE50401 SE50404 SE50406 SE50401 SE50404 SE50404 SE50404 2. Burned-Out Coil: Check for open-circuited coil. Replace coil as necessary. Check supply voltage; it must be the same as specified on nameplate. 3. Low Voltage: Check voltage across the coil lead. Voltage must be at least 85% of nameplate rating. 4. Incorrect Pressure: Check valve pressure. Pressure to valve must be within range specified on nameplate. 5. Excessive Leakage: Disassemble valve and clean all parts. If leakage continues, replace all parts as supplied with a Rebuild Kit. Coil Replacement Valve Reassembly WARNING: Turn off electrical power supply. 1. Reassemble in reverse order of disassembly. Use exploded view for identification and placement of parts. 1. Disconnect coil lead wires and green grounding wire if present. 2. Remove retaining clip, nameplate and housing. 2. Lubricate all gaskets with DOW CORNING 111® Compound lubricant or an equivalent high-grade silicone grease. WARNING: When metal retaining clip disengages, it will spring upward. 3. Position support and inner and outer body gaskets in valve body. 3. Slip spring washer and coil off the solenoid base subassembly. 4. Position lip seal, flanged end up, onto piston assembly. Install piston assembly with lip seal into support in valve body cavity. 4. Coil is now accessible for replacement. Reassemble in reverse order of disassembly. Use Solenoid Valve Exploded View Drawing for identification and placement of parts. CAUTION: Solenoid must be fully reassembled because the housing and internal parts complete the magnetic circuit. Valve Disassembly WARNING: Depressurize valve and turn off electrical power supply. 1. Disassemble valve in an orderly fashion. Use exploded view for identification and placement of parts. 2. If necessary, disconnect coil lead wires, grounding wire (if present), and rigid conduit from solenoid housing, 3. Remove retaining clip and slip the entire solenoid enclosure off the solenoid base subassembly. WARNING: When metal retaining clip disengages, it will spring upward, 4. Unscrew solenoid base sub-assembly and remove core assembly, core spring, and solenoid base gasket. 5. Remove bonnet screws, valve bonnet, piston assembly, lip seal, support, inner and outer body gaskets. 6. All parts are now accessible to clean or replace; Replace worn or damaged parts. However, for best results, replace all parts as supplied with an Rebuild Kit. 5. Replace valve bonnet and bonnet screws. Torque bonnet screws in a crisscross manner to 95 ±10 inch-pounds (10,7 ±1,1 newtonmeters). 6. Replace solenoid base gasket, core assembly, and solenoid base sub-assembly. Torque solenoid base sub-assembly to 175 ±25 inch-pounds (19,8 ±2,8 newton-meters). 7. Replace solenoid enclosure and retaining clip. 8. Restore line pressure and electrical power supply to valve. 9. After maintenance is completed, operate the valve a few times to be sure of proper opening and closing. MRC 7000 ENABLE MODE PROCEDURE (1&2 PEN) Press and hold both keys until "EnAb " appears (about 10 seconds). When you release the keys "EtSt " will appear. EnAb For Cook Chill Direct Steam Mixer Kettles Reference page #36 in the MRC 7000 Installation, Wiring, Operation Manual, Form 2877, Edition 6, May 1994 update. To prevent tampering, your programmer comes from the factory with the programming modes turned "oFF ". If adjustment is required then the modes must be turned "ON " before they are accessible. We recommend that when the adjustments have been completed you turn off the programming modes again. To turn on the mode required perform the following steps: Push to turn "on " Push to turn "oFF " Test Mode Calibration Mode EtSt oFF Factory Setting ECAL oFF Factory Setting Program Mode EPro oFF Factory Setting Pen1 key AUTO/MAN Tune Mode AUTO Etun SCROLL Key oFF Factory Setting MAN UP Key AUTO DOWN Key Manual (Stby)Mode ESbY Pen 2 key AUTO/MAN MAN oFF Factory Setting MAN Setpoint Select Mode (optional) ESPS oFF Factory Setting OUT1 OUT2 ALRM SP CAL 9900 Controls Drawing 1. Turn MAIN POWER SWITCH to "ON ". 2. Press the scroll key " ESPC " until "CtrL" is displayed. 3. Press and hold the " " and " " keys at the same time. All the display lamps will light. 4. After 10 seconds the display lights will go out and "EnAb " will be displayed. Release the " " and " " keys. "EtSt " will appear. 5. Repeatedly press the " " key until the desired mode is displayed. 6. Press the scroll key " " once to display the mode’s setting ("ON " or "oFF "). 7. Press the " "ON ". Setpoint Change " key to turn the desired mode 8. To turn desired mode "oFF " follow steps 1-5 and then press " " key. on Factory Setting Note: Pressing the up key while any of the modes are displayed will exit you from the "EnAb" program. MRC 7000 Enable Mode Flow Chart WIRING DIAGRAM SINGLE KETTLES WIRING DIAGRAM TWIN KETTLES FLOW PATH FOR HYDRAULIC SYSTEM Hydraulic Cylinder Variable Restrictor Valve OUT 2 Way Solenoid Valve UP Check Valve Secondary Hydraulic Motor Primary Hydraulic Motor DOWN MIX IN LIFT Variable Restrictor Valve To Tank 3 Way Solenoid Valve Relief Valve set at 1000 psi Pump To Tank SPARE PARTS LIST ITEM ON. DESCRIPTION QTY. DOMESTIC QTY. OVERSEAS Spare Parts SE50426 SE50428 KE52895 KE52936 KE003209-1 KE003209-3 KE003209-6 KE003209-7 KE02274 KE603208-8 KE603208-9 KE50753-10 KE00860 SE50224 KE53962 KE51834 SE50094 KE54834-3 KE54834-2 KE52701 UR50077 KE50579 FA00012 KE50580 KE603208-9 FA00016 SK50445 SK52936 KE50750-1 Air Filter Element "O" Ring for Air Filter Air Regulator Fuse Switch Assembly - On/Off - Maintained Switch Assembly - On/Off/On - Maintained Switch Assembly - Momentary Spring Return Switch Assembly - Momentary Spring Return Capacitor Assembly Capacitor Cartridge - NC Capacitor Cartridge - NO Relay Cable and Bracket Assembly - Speed Control Solenoid Valve Coil Blade Stop Ring Scraper Blades Oil Filter Solenoid Valve, 3/4" - 50 psi. Solenoid Valve, 3/8" Steam Trap Thermostat Circuit Breaker "O" Ring for Circuit Breaker Water Resistant Boot for Circuit Breaker Contact Block "O" Ring for Faucet Spout Fuse - 3 amps Fuse - 1 amps Contactor 1 1 --1 --------2 2 2 2 ----2 2 1 ----------1 1 --2 1 1 --- 1 1 1 1 1 1 1 1 2 2 2 2 1 1 2 2 1 1 1 1 1 1 1 1 1 2 1 1 1 1 4 4 4 1 4 4 4 ----- 1 1 FLUSH PISTON VALVE Spare Parts KE55210 KE55248 KE55250 KE55255 WELD RING, KETTLE BOTTOM OUTLET BUNA-N O-RING BUNA-N O-RING BUNA-N O-RING BUTTERFLY VALVE Spare Parts SE50433 SE50433-1 Seat - 2" Seat - 2"
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement