VN340SP-E
Quad high-side smart power solid state-relay
Datasheet - production data
• Built-in current limiter
• Undervoltage shutdown
• Open drain diagnostic output
• Fast demagnetization of inductive loads
3RZHU62
• Conformity to IEC 61131-2
Description
Features
Type
Vdemag(1) RDS(on)(1)
VN340SP-E VCC-55 V
0.2 Ω
IOUT(1)
VCC(1)
0.7 A
36 V
1. Per channel
• Output current: 0.7 A per channel
• Digital I/O clamped at 32 V minimum voltage
• Shorted load and overtemperature protections
The VN340SP-E is a monolithic device developed
using ST VIPower™ technology, intended to drive
four independent resistive or inductive loads with
one side connected to ground. Active current
limitation avoids dropping the system power
supply in case of shorted load. Built-in thermal
shutdown protects the chip from overtemperature
and short-circuit. The open drain diagnostic
output indicates overtemperature conditions.
Each I/O is pulled down when the
overtemperature condition of the relative channel
is verified.
• Protection against loss of ground
Figure 1. Block diagram
*,3*/0
December 2014
This is information on a product in full production.
DocID11468 Rev 6
1/17
www.st.com
Contents
VN340SP-E
Contents
1
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4
Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5
Switching time waveforms and truth table . . . . . . . . . . . . . . . . . . . . . . . 9
6
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6.1
PowerSO-10 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
6.2
PowerSO-10 packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2/17
DocID11468 Rev 6
VN340SP-E
1
Absolute maximum ratings
Absolute maximum ratings
Table 1. Absolute maximum ratings
Symbol
Parameter
Value
Unit
VCC
Power supply voltage
45
V
-VCC
Reverse supply voltage
-4
V
IOUT
Output current (continuous
Internally limited
A
-6
A
IR
Reverse output current (per channel)
IIN
Input current (per channel)
± 10
mA
IDIAG
Diag pin current
± 10
mA
VESD
Electrostatic discharge (R = 1.5 kΩ;
C = 100 pF)
2000
V
Single pulse avalanche energy one
channel active TJ = 125 °C,
ILOAD = 0.625 A
10
EAS
PTOT
Power dissipation at TC = 25 °C
TJ
Junction operating temperature
TSTG
J
Single pulse avalanche energy all
channels active simultaneously
TJ = 125 °C,
ILOAD = 0.625 A
2
W
Internally limited
°C
Storage temperature
-55 to 150
°C
Table 2. Thermal data
Symbol
Parameter
(1)
RthJC
Thermal resistance junction-case
RthJA
Thermal resistance junction-ambient(2)
Value
Unit
3
°C/W
50
°C/W
1. Per channel
2. When mounted, minimum recommended pad size on FR-4 board
DocID11468 Rev 6
3/17
17
Pin connections
2
VN340SP-E
Pin connections
Figure 2. Connection diagram (top view)
*,3*/0
Figure 3. Current and voltage conventions
*,3*/0
4/17
DocID11468 Rev 6
VN340SP-E
3
Electrical characteristics
Electrical characteristics
10 V < VCC< 36 V; -40 °C < TJ = 125 °C unless otherwise specified
Table 3. Power section
Symbol
VCC
RDS(on)
IS
VOL
Vdemag
ILGND
Parameter
Test conditions
Min.
Supply voltage
Typ.
10
On-state resistance
Supply current
Low-state output
voltage
Max.
Unit
36
V
IOUT = 0.5 A; TJ = 25 °C
0.2
IOUT = 0.5 A; TJ = 85 °C
0.32
IOUT = 0.5 A; TJ = 125 °C
0.4
All channels OFF
On-state; VIN = 30 V;
IOUT = 0 V (TJ = 125 °C)
1
mA
6
VIN = VIL, RLOAD = 10 mΩ
Output voltage at turn- IOUT = 0.5 A;
off
LLOAD = 1 mH
Ω
1.5
VCC-65 VCC-55 VCC-45
VCC = VINn = VGND=
Output current at turn- VSTAT = 18 to 30 V
off
Tamb = 25 to 85 °C
(see Figure 6)
V
V
2
mA
Typ.
Max.
Unit
52
100
94
250
34
50
8
20
Table 4. Switching (VCC = 24 V)
Symbol
td(on)
tr
td(off)
tf
Parameter
Test conditions
Min.
Turn-on delay time of
output current
Rise time of output current IOUT = 0.5 A, resistive
load input rise time
Turn-off delay time of
< 0.1 μs TJ = 25 °C
output current
Fall time of output current
DocID11468 Rev 6
-
μs
5/17
17
Electrical characteristics
VN340SP-E
Table 5. Logic input
Symbol
Parameter
VIL
I/O input low level voltage
VIH
I/O input high level voltage
VI(HYST)
IIN
VICL
Test conditions
Min.
Typ.
Max.
Unit
2
3.5
I/O input hysteresis
voltage
V
0.5
I/O input current
VIN = 30 V
I/O input clamp voltage(1)
IIN = 1 mA
25
32
μA
36
V
IIN = -1 mA
-0.7
1. The input voltage is internally clamped at 32 V minimum, the input pins can be connected to a higher
voltage via the external resistor without exceeding 10 mA
Table 6. Protection and diagnostic
Symbol
Parameter
Test conditions
VDIAG(1)
Status voltage output low
VSCL(1)
Status clamp voltage
VUSD
Undervoltage shutdown
ILIM
DC short-circuit current
Min.
Typ.
IDIAG = 5 mA (fault
condition)
IDIAG = 1 mA
32
IDIAG = 1 mA
VCC = 24 V;
RLOAD < 10 mΩ
Max.
Unit
1
V
36
-0.7
V
5
8
V
0.7
2
A
IOVPK
Peak short-circuit current
VCC = 24V; VIN = 30 V;
RLOAD < 10 mΩ
4
A
IDIAGH
Leakage on DIAG pin in
high-state
VDIAG = 24 V
25
μA
ILOAD
Output leakage current
50
μA
100
μs
tSC
TTSD
TR
VCC = 10 to 36 V;
VIN = VIL
Delay time of current
limiter
Thermal shutdown
temperature
150
170
°C
Thermal reset
temperature
135
155
°C
1. Status determination > 100 μs after the switching edge
Note:
6/17
If INPUT pin floats, the corresponding channel automatically switches OFF. If GND pin is
disconnected, the channel switches OFF provided that VCC doesn’t exceed 36 V
DocID11468 Rev 6
VN340SP-E
4
Test circuits
Test circuits
Figure 4. Avalanche energy test circuit
*,3*/0
Figure 5. Peak short-circuit test diagram
*,3*/0
DocID11468 Rev 6
7/17
17
Test circuits
VN340SP-E
Figure 6. ILGND test configuration
*,3*/0
8/17
DocID11468 Rev 6
VN340SP-E
5
Switching time waveforms and truth table
Switching time waveforms and truth table
Figure 7. Switching waveforms
*,3*/0
Figure 8. Switching parameter test conditions
*,3*/0
DocID11468 Rev 6
9/17
17
Switching time waveforms and truth table
VN340SP-E
Table 7. Truth table
Conditions
MCOUTn
I/On
OUTPUTn
Diagnostic
Normal operation
L
H
L
H
L
H
H
H
Overtemperature
L
H
L
L
L
L
H
L
Undervoltage
L
H
L
H
L
L
H
H
Short load (current
limitation)
L
H
L
H
L
H
H
H
Figure 9. Driving circuit
*,3*/0
10/17
DocID11468 Rev 6
VN340SP-E
6
Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
6.1
PowerSO-10 package information
Figure 10. PowerSO-10 outline
0068039F1_Rev.F
DocID11468 Rev 6
11/17
17
Package information
VN340SP-E
Table 8. PowerSO-10 mechanical data
mm
Dim.
Min.
Typ.
A
3.70
A1
0.00
0.10
A2
3.40
3.60
A3
1.25
1.35
b
0.40
0.53
c
0.35
0.55
D
9.40
9.60
D1(1)
7.40
7.60
E
13.80
14.40
E1(1)
9.30
9.50
E2
7.20
7.60
E3
5.90
6.10
e
1.27
L
0.95
1.65
<
0o
8o
1. Resin protrusion is not included (max. value 0.20 mm per side)
12/17
Max.
DocID11468 Rev 6
VN340SP-E
6.2
Package information
PowerSO-10 packing information
Figure 11. PowerSO-10 tape outline
$0Y
Note:
Drawing is not in scale
Figure 12. PowerSO-10 reel outline
7
PPPLQ
$FFHVVKROH
DWVORWORFDWLRQ
%
'
&
1
$
7DSHVORW
LQFRUHIRU
)XOOUDGLXV
7DSHVWDUW
PPPLQZLGWK
*PHDVXUHG
$WKXE
$0Y
DocID11468 Rev 6
13/17
17
Package information
VN340SP-E
Table 9. PowerSO-10 tape and reel mechanical data
mm
Ref.
Note:
14/17
Min.
Typ.
Max.
A0
14.9
15.0
15.1
B0
9.9
10.0
10.1
K0
4.15
4.25
4.35
F
11.4
11.5
11.6
E
1.65
1.75
1.85
W
23.7
24.0
24.3
P2
1.9
2.0
2.1
P0
3.9
4.0
4.1
P1
23.9
24.0
24.1
T
0.025
0.30
0.35
D(Ø)
1.50
1.55
1.60
10 sprocket hole pitch cumulative tolerance ±0.2 mm
DocID11468 Rev 6
VN340SP-E
7
Ordering information
Ordering information
Table 10. Ordering information
Order code
Package
VN340SP-E
Packing
Tube
PowerSO-10
VN340SPTR-E
Tape and reel
DocID11468 Rev 6
15/17
17
Revision history
8
VN340SP-E
Revision history
Table 11. Document revision history
Date
Revision
05-Sep-2005
1
Initial release.
27-Jun-2006
2
Updated mechanical data.
18-Sep-2006
3
Updated mechanical data and added PowerSO-10 tape
and reel.
31-Oct-2006
4
Updated typo in electrical characteristic temperature
conditions.
05-Mar-2007
5
Document reformatted, typo in note 1.
6
Updated the title.
Updated EAS parameter in Table 1 and updated Table 5
and Table 6.
Minor text changes.
04-Dec-2014
16/17
Changes
DocID11468 Rev 6
VN340SP-E
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2014 STMicroelectronics – All rights reserved
DocID11468 Rev 6
17/17
17
">
