User`s guide | Casio WK3500 Musical Instrument User Manual

E
USER’S GUIDE
WK3100-E-1
WK3100_e_cover.p65
1
04.3.26, 0:10 PM
GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A. (not applicable to other areas).
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Important!
Please note the following important information before using this product.
• Before using the optional AD-12 Adaptor to power the unit, be sure to check the AC Adaptor for
any damage first. Carefully check the power cord for breakage, cuts, exposed wire and other serious
damage. Never let children use an AC adaptor that is seriously damaged.
• Never attempt to recharge batteries.
• Do not use rechargeable batteries.
• Never mix old batteries with new ones.
• Use recommended batteries or equivalent types.
• Always make sure that positive (+) and negative (–) poles are facing correctly as indicated near the
battery compartment.
• Replace batteries as soon as possible after any sign they are getting weak.
• Do not short-circuit the battery terminals.
• The product is not intended for children under 3 years.
• Use only CASIO AD-12 adaptor.
• The AC adaptor is not a toy.
• Be sure to disconnect the AC adaptor before cleaning the product.
CASIO ELECTRONICS CO., LTD.
Unit 6, 1000
North Circular Road
London NW2 7JD, U.K.
This mark is valid in the EU countries only.
Please keep all information for future reference.
735A-E-002A
WK3100_e_00.p65
2
04.3.26, 0:10 PM
Safety Precautions
Congratulations on your selection of the CASIO
electronic musical instrument.
• Before using the instrument, be sure to carefully
read through the instructions contained in this
manual.
• Please keep all information for future reference.
Symbols
Various symbols are used in this user’s guide and on
the product itself to ensure that the product is used
safely and correctly, and to prevent injury to the user
and other persons as well as damage to property.
Those symbols along with their meanings are shown
below.
DANGER
This symbol indicates information that, if ignored
or applied incorrectly, creates the danger of death
or serious personal injury.
Symbol Examples
This triangle symbol ( ) means that the
user should be careful. (The example at
left indicates electrical shock caution.)
This circle with a line through it ( )
means that the indicated action must not
be performed. Indications within or
nearby this symbol are specifically
prohibited. (The example at left indicates
that disassembly is prohibited.)
The black dot ( ) means that the
indicated action must be performed.
Indications within this symbol are actions
that are specifically instructed to be
performed. (The example at left indicates
that the power plug must be unplugged
from the electrical socket.)
WARNING
This indication stipulates matters that have the risk
of causing death or serious injury if the product is
operated incorrectly while ignoring this indication.
CAUTION
This indication stipulates matters that have the risk
of causing injury as well as matters for which there
is the likelihood of occurrence of physical damage
only if the product is operated incorrectly while
ignoring this indication.
E-1
735A-E-003A
WK3100_e_01-09.p65
1
04.3.26, 0:10 PM
Safety Precautions
DANGER
Alkaline Batteries
Perform the following steps immediately if
fluid leaking from alkaline batteries ever
gets into your eyes.
1. Do not rub your eyes! Rinse them with
water.
2. Contact your physician immediately.
Leaving alkaline battery fluid in your eyes
can lead to loss of sight.
WARNING
Smoke, Strange Odor, Overheating
Continued use of the product while it is
emitting smoke, a strange odor, or heat
creates the risk of fire and electric shock.
Take the following steps immediately.
1. Turn off power.
2. If you are using the AC adaptor for
power, unplug it from the wall outlet.
3. Contact your original retailer or an
authorized CASIO Service Provider.
AC Adaptor
● Misuse of the AC adaptor creates the risk
of fire and electric shock. Always make
sure you observe the following
precautions.
• Be sure to use only the AC adaptor
that is specified for this product.
• Use only a power source whose voltage
is the within the rating marked on the
AC adaptor.
• Do not overload electrical outlets and
extension cords.
● Misuse of the AC adaptor’s electric cord
can damage or break it, creating the risk
of fire and electric shock. Always make
sure you observe the following
precautions.
• Never place heavy objects on the cord
or subject it to heat.
• Never try to modify the cord or subject
it to excessive bending.
• Never twist or stretch the cord.
• Should the electric cord or plug become
damaged, contact your original retailer
or authorized CASIO Service Provider.
● Never touch the AC adapter while your
hands are wet.
Doing so creates the risk of electric shock.
• Use the AC adaptor where it will not
be splashed with water. Water creates
the risk of fire and electric shock.
• Do not place a vase or any other
container filled with liquid on top of
the AC adaptor. Water creates the risk
of fire and electric shock.
Do not incinerate the product.
Never throw the product into fire.
Doing so can cause it to explode, creating
the risk of fire and personal injury.
Water and Foreign Matter
Water, other liquids, and foreign matter
(such as pieces of metal) getting into the
product create the risk of fire and electric
shock. Take the following steps
immediately.
1. Turn off power.
2. If you are using the AC adaptor for
power, unplug it from the wall outlet.
3. Contact your original retailer or an
authorized CASIO Service Provider.
Disassembly and Modification
Never try to take this product apart or
modify it in any way. Doing so creates the
risk of electric shock, burn injury, or other
personal injury. Leave all internal
inspection, adjustment, and maintenance up
to your original retailer or authorized
CASIO Service Provider.
Dropping and Impact
Continued use of this product after it has
been damaged by dropping or subjecting it
to strong impact creates the risk of fire and
electric shock. Take the following steps
immediately.
1. Turn off power.
2. If you are using the AC adaptor for
power, unplug it from the wall outlet.
3. Contact your original retailer or an
authorized CASIO Service Provider.
E-2
WK3100_e_01-09.p65
735A-E-004C
2
04.3.26, 0:10 PM
Safety Precautions
Plastic Bags
Never place the plastic bag the product
comes in over your head or in your mouth.
Doing so creates the risk of suffocation.
Particular care concerning this precaution
is required where small children are
present.
Keep off of the product and stand.*
Climbing onto the product or stand can
cause it to tip over or become damaged.
Particular care concerning this precaution
is required where small children are
present.
Location
Avoid locating the product on an unstable
stand, on an uneven surface, or any other
unstable location. An unstable location can
cause the product to fall over, creating the
risk of personal injury.
CAUTION
AC Adaptor
Misuse of the AC adaptor creates the risk
of fire and electric shock. Always make sure
you observe the following precautions.
• Do not locate the electric cord near a
stove or other sources of heat.
• Never pull on the cord when unplugging
from the electrical outlet. Always grasp
the AC adaptor when unplugging.
AC Adaptor
Misuse of the AC adaptor creates the risk
of fire and electric shock. Always make sure
you observe the following precautions.
• Insert the AC adaptor into the wall outlet
as far as it will go.
• Unplug the AC adaptor from the wall
outlet during lightening storms or before
leaving on a trip or other long-term
absence.
• At least once a year, unplug the AC
Adaptor from the wall outlet and wipe
away any dust that is built up in the area
around the prongs of the plug.
Relocating the Product
Before relocating the product, always
unplug the AC adaptor from the wall outlet
and disconnect all other cables and
connecting cords. Leaving cords connected
creates the risk of damage to the cords, fire,
and electric shock.
Cleaning
Before cleaning the product, always unplug
the AC adaptor from the wall outlet first.
Leaving the AC adaptor plugged in creates
the risk of damage to the AC adaptor, fire,
and electric shock.
Batteries
Misuse of batteries can cause them to leak
resulting in damage to nearby objects, or to
explode, creating the risk of fire and
personal injury. Always make sure you
observe the following precautions.
• Use only batteries that are specified for
use with this product.
• Remove batteries from the product if you
do not plan to use it for a long time.
Connectors
Connect only the specified devices and
equipment to the product’s connectors.
Connection of a non-specified device or
equipment creates the risk of fire and
electric shock.
E-3
735A-E-005A
WK3100_e_01-09.p65
3
04.3.26, 0:10 PM
Safety Precautions
Location
Avoid the following locations for this
product. Such locations create the risk of
fire and electric shock.
• Areas subject to high humidity or large
amounts of dust
• In food preparation areas or other areas
subject to oil smoke
• Near air conditioning equipment, on a
heated carpet, in areas exposed to direct
sunlight, inside of a vehicle parked in
the sun, or any other area that subjects
the product to high temperatures
Display Screen
• Never push on the display screen’s LCD
panel or subject it to strong impact. Doing
so can cause the LCD panel’s glass to
crack, creating the risk of personal injury.
• Should the LCD panel ever crack or
break, never touch the liquid inside of
the panel. LCD panel liquid can cause
skin irritation.
• Should LCD panel liquid ever get inside
your mouth, immediately wash out your
mouth with water and contact your
physician.
• Should LCD panel liquid ever get into
your eyes or onto your skin, rinse with
clear water for at least 15 minutes, and
then contact a physician.
IMPORTANT!
When using batteries, be sure to replace them or shift to
one of the alternate power sources whenever you notice
any of the following symptoms.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Dim power indicator
Instrument does not turn on
Display that is flickering, dim, or difficult to read
Abnormally low speaker/headphone volume
Distortion of sound output
Occasional interruption of sound when playing at high
volumes
Sudden power failure when playing at high volumes
Flickering or dimming of the display when playing at high
volume
Continued sound output even after you release a key
A tone that is totally different from the one that is selected
Abnormal rhythm pattern and demo tune play
Abnormally low microphone volume (WK-3100 only)
Distortion of microphone input (WK-3100 only)
Dim power supply indicator when a microphone is used
(WK-3100 only)
Sudden power failure when using the microphone
(WK-3100 only)
Loss of power, sound distortion, or low volume when
playing from a connected computer or MIDI device
Sudden power failure while reading from or writing to a
diskette (WK-3500 only)
Sound Volume
Do not listen to music at very loud volumes
for long periods. Particular care concerning
this precaution is required when using
headphones. High volume settings can
damage your hearing.
Heavy Objects
Never place heavy object on top of the
product.
Doing so can make the product top heavy,
causing the product to tip over or the object
to fall from it, creating the risk of personal
injury.
Correct Stand* Assembly
An incorrectly assembled stand can tip over,
causing the product to fall and creating the
risk of personal injury.
Make sure you assemble the stand correctly,
following the assembly instructions that
come with it. Make sure you mount the
product on the stand correctly.
* Stand is available as an option.
E-4
WK3100_e_01-09.p65
735A-E-006C
4
04.3.26, 0:10 PM
Introduction
Congratulations upon your selection of this CASIO musical instrument. This keyboard provides you with the following features
and functions.
❐ 516 Tones Include Rich Advanced Tones
A total of 300 Advanced Tones are programmed with DSP tones to make them richer and more powerful. Advanced tones like
Stereo Piano and Tremolo Electric Piano enhance the Piano and Electric Piano tones to create a totally new sound.
❐ 50 Drawbar Organ Tones
In addition to the 516 standards tones, the keyboard also includes 50 realistic drawbar organ tones. Drawbar organ tones can be
controlled using nine digital drawbars. You can also select percussion or key click, and even edit the parameters of preset tone
and save up to 100 original tones in user tone memory.
❐ Flash Memory
Built-in Flash memory lets you expand your selection of tones and rhythms by downloading data from the CASIO MUSIC SITE,
or from other sources. You can also store up to 200 SMF format music files for playback.
❐ PIANO SETTING Button
The press of a button optimizes the keyboard setup for piano play.
❐ 140 Preset Rhythms + 16 User Rhythms
A selection of 140 rhythms includes accompaniments for everything from rock to pops and jazz.
You can also transfer accompaniment data from your computer and store up to 16 of them as user rhythms in keyboard memory.
❐ Auto Accompaniment
Simply play a chord and the corresponding rhythm, bass and chord parts play automatically. One-touch Preset instantly recalls
the most suitable tone and tempo settings to match the rhythm you are using.
❐ Big, Information-packed Display
A big built-in display shows chord names, tempo setting, keyboard information, staff notation of notes played, and more for full
support of all your keyboard play. A built-in backlight keeps the display easy to read, even in total darkness.
❐ Song Memory
Record up to six parts in memory, along with their tone, volume, pan position, and other parameters for later playback. Realistic
ensemble play can also be created using the Auto Accompaniment function.
❐ Synthesizer Mode
Edit built-in sounds to produce your own original creations. Up to 120 of your own sounds can be stored in memory for recall,
just like the built-in tones.
❐ General MIDI compatibility
The General MIDI tones of this keyboard let you connect to a personal computer to enjoy “desktop music” capabilities. This
keyboard can be used as a desktop music input device or sound source, and it's just the thing for playback of commercially
available pre-recorded General MIDI music software.
❐ Powerful effects
A collection of powerful effects, such as DSP reverb, chorus, and more, give you total control over the type of sound you want.
You can even change the parameters of an effect to create your own, original effects. A 4-band equalizer is also included.
E-5
735A-E-007B
WK3100_e_01-09.p65
5
04.3.26, 0:10 PM
Introduction
❐ Mixer
You can specify tone, volume, pan position, and other parameters for each built-in Auto Accompaniment part. You can also
control the same parameters for each channel during MIDI input.
❐ Registration Memory
Keyboard setups can be stored in memory for later recall and instant settings whenever you need them. Up to 32 setups (4 setups
x 8 banks) can be stored in registration memory.
❐ Data download from your computer
You can use your computer to download data from the CASIO MUSIC SITE.
❐ SmartMediaTM Card Slot
A built-in SmartMedia card slot helps to simplify transfer of data from a computer and lets you store volumes of data for later
recall when you need it. You can also load a card with a standard MIDI file (SMF) and play it back on the keyboard.
❐ Built-in floppy disk drive (WK-3500 only)
Save original tones or songs you created with the Song Memory to disk for long-term storage. You can also load a disk with a
standard MIDI file (SMF) and play it back on the keyboard.
❐ Microphone Jack (WK-3100 only)
Connect a commercially available microphone* and you can sing as you play, or sing with accompaniment from Song Memory or
SMF playback.
* If a microphone was included with your keyboard, use that microphone.
E-6
WK3100_e_01-09.p65
735A-E-008C
6
04.3.26, 0:10 PM
Contents
Safety Precautions ................ E-1
Introduction ........................... E-5
Contents ................................. E-7
General Guide ...................... E-10
Attaching the Score Stand ..................... E-11
Playing a Demo Tune ............................. E-12
About the display ................................... E-14
Power Supply ...................... E-16
Using the Drawbar Organ
Mode ..................................... E-26
To select a drawbar organ tone .............. E-28
To edit a drawbar organ tone ................. E-28
Parameter Details .................................. E-29
To save an edited drawbar organ tone ... E-30
Applying Effects to
Tones .................................... E-31
Effect Blocks .......................................... E-31
Selecting a DSP Type ............................ E-32
About the DSP Button ............................ E-34
Using batteries ....................................... E-16
Selecting REVERB ................................ E-34
Using the AC Adaptor ............................. E-17
Selecting CHORUS ................................ E-36
Auto Power Off ....................................... E-17
Using the Equalizer ................................ E-37
Turning Off the Keyboard ....................... E-18
Memory Contents ................................... E-18
Auto Accompaniment ......... E-38
Connections ........................ E-19
About the MODE Button ........................ E-38
Selecting a Rhythm ................................ E-39
Using the microphone jack
(WK-3100 only) ...................................... E-21
Playing a Rhythm ................................... E-39
Adjusting the Tempo ............................... E-39
Basic Operations ................. E-22
Using Auto Accompaniment ................... E-40
To play the keyboard .............................. E-22
Using an Intro Pattern ............................ E-43
Selecting a Tone..................................... E-22
Using a Fill-in Pattern ............................. E-43
PIANO SETTING Button ........................ E-24
Using a Rhythm Variation ....................... E-43
Using the PITCH BEND Wheel .............. E-25
Synchro Starting Accompaniment
with Rhythm Play ................................... E-44
Using the MODULATION ....................... E-25
Finishing with an Ending Pattern ........... E-44
Using One-touch Preset ......................... E-45
E-7
735A-E-009C
WK3100_e_01-09.p65
7
04.3.26, 0:10 PM
Contents
Using Auto Harmonize ........................... E-45
Adjusting the Accompaniment Volume ... E-46
Correcting Mistakes While Step
Recording ............................................... E-69
Editing Memory Contents ....................... E-70
Mixer Function ..................... E-47
Editing a Song ........................................ E-72
What you can do with the Mixer ............. E-47
Turning Channels On and Off ................ E-47
Using the Parameter Edit Mode ............. E-48
How Parameters Work ........................... E-49
Keyboard Settings .............. E-74
Using Layer ............................................ E-74
Using Split .............................................. E-75
Using Layer and Split Together .............. E-76
Synthesizer Mode ................ E-51
Transposing the Keyboard ..................... E-77
Synthesizer Mode Functions .................. E-51
Using Touch Response .......................... E-78
Creating a User Tone ............................. E-54
Tuning the Keyboard .............................. E-78
Storing a User Tone In Memory ............. E-57
Changing Other Settings ........................ E-79
Registration Memory .......... E-59
Using the SMF Player ......... E-84
Registration Memory Features ............... E-59
Playing Back an SMF ............................. E-86
To Save a Setup in Registration
Memory .................................................. E-60
Configuring Other Settings ..................... E-87
To Recall a Setup from Registration
Memory .................................................. E-60
Song Memory Function ...... E-61
MIDI ....................................... E-89
What is MIDI? ........................................ E-89
General MIDI .......................................... E-89
Tracks .................................................... E-61
Sending and Receiving MIDI
Messages ............................................... E-90
Basic Song Memory operations ............. E-61
MIDI Settings ......................................... E-90
Using Real-time Recording .................... E-62
Using the Data Download Service ......... E-91
Mixer Mode Settings .............................. E-63
Playing Back from Song Memory ........... E-64
Recording Melody and Chords
with Step Recording ............................... E-64
Recording Multiple Tracks ...................... E-67
Saving Data .......................... E-92
Using a SmartMedia Card ...................... E-93
Using the Floppy Disk Drive
(WK-3500 Only) ..................................... E-94
E-8
WK3100_e_01-09.p65
735A-E-010A
8
04.3.26, 0:10 PM
Contents
Using External Storage Media ............... E-96
Saving Files ........................................... E-98
Loading a File ........................................ E-99
Renaming a File ................................... E-100
Deleting a File ...................................... E-101
Formatting External Storage Media ..... E-102
Inputting Characters ............................. E-103
SmartMedia Card Error Messages ...... E-104
Disk Drive Error Messages
(WK-3500 Only) ................................... E-105
Troubleshooting ................ E-106
Specifications .................... E-109
Care of your Instrument ... E-112
Appendix ............................... A-1
Tone List ................................................... A-1
Drum Assignment List ............................ A-12
Rhythm List ............................................ A-14
Fingered Chord Chart ............................ A-15
Effect List ............................................... A-17
DSP Algorithm List ................................. A-19
MIDI Implementation Chart
Company and product names used in this
manual may be registered trademarks of
others.
E-9
735A-E-011A
WK3100_e_01-09.p65
9
04.3.26, 0:10 PM
General Guide
1
2 3
4 5 6
8
9
0
A
M
*3
R S
B
7
D E
C
N
I
O
P
J
T
G
H
L
M
U
Z
[
\
]
W
a
_
E-10
WK3100_e_10-25.p65
K
Q *2
*1
V
Y
F
X
b
c
735A-E-012A
10
04.3.26, 0:10 PM
General Guide
• Illustrations in this User’s Guide shows the WK-3500.
1 POWER button
M Speaker
2 Power indicator
N Rhythm list
3 MODE button
O Tone list
4 EFFECT button
P Display
5 SYNTH button
Q DEMO button*4
6 MIXER button
R 쎲WK-3500
PHONES terminal
7 TRANSPOSE/FUNCTION button
8 VOLUME knob
9 ONE TOUCH PRESET button
0 ACCOMP VOLUME button
A SONG MEMORY button
쎲WK-3100
MIC IN jack
쎲WK-3000
PHONES/OUTPUT terminal
S CHORD root names
B 쎲WK-3500
DISK/CARD button
T Percussion instrument list
U Chord types name
쎲WK-3100/WK-3000
CARD button
V SMF PLAYER button
C DATA ACCESS lamp
W CHANNEL button(1~16, DSP)/drawbar buttons
D RHYTHM button
X DRAWBAR ORGAN button
E TONE button
Y INTRO/ENDING 1/2 buttons
F DSP button
Z VARIATION/FILL-IN 1/2 buttons
G PIANO SETTING button
[ SYNCHRO/FILL-IN NEXT button
H [왖]/[왔]/[왗]/[왘] CURSOR button
\ START/STOP button
I EXIT button
] TEMPO buttons
J AUTO HARMONIZE button
_ SONG MEMORY TRACK buttons
a) BANK button
b) REGISTRATION buttons
c) STORE button
K SPLIT button
L LAYER button
Attaching the Score Stand*1
Insert the score stand into the slot at the top
of the keyboard as shown in the illustration.
E-11
735A-E-013C
WK3100_e_10-25.p65
11
04.3.26, 0:10 PM
General Guide
*2
a Number buttons
• For input of numbers to
change displayed settings.
• Negative values can be
changed only by using [+]
and [–] to increment and
decrement the displayed
value.
b [+]/[–] buttons
(YES/NO)
*3
• WK-3500
• WK-3100/WK-3000
c PITCH BEND wheel
c
d
d MODULATION wheel
c MODULATION button
d MODULATION button lamp
e PITCH BEND wheel
c
d
e
Playing a Demo Tune*4
Pressing the DEMO button starts demo tune play. There are 3 demo tunes, which continuously play in sequence. To stop demo
tune play, press either the DEMO button or the START/STOP button.
NOTE
• Pressing the [+]/[–] buttons skips to the next demo tune.
• The PIANO SETTING button, Layer, and Split are disabled while a demo tune is playing.
Front Panel
• WK-3500 only
f Access lamp
g Eject button
g
f
E-12
WK3100_e_10-25.p65
735A-E-014C
12
04.3.26, 0:10 PM
General Guide
Rear Panel
• WK-3500
• WK-3000
h i
j
k
l
h i
OUT
j
k
SUSTAIN/
ASSIGNABLE JACK
DC 12V
MIDI
MIDI
IN
SUSTAIN/
ASSIGNABLE JACK
R
L/MONO
LINE OUT
DC 12V
OUT
IN
h MIDI OUT terminal
h MIDI OUT terminal
i MIDI IN terminal
i MIDI IN terminal
j SUSTAIN/ASSIGNABLE JACK terminal
j SUSTAIN/ASSIGNABLE JACK terminal
k LINE OUT R, LINE OUT L/MONO terminal
k DC 12V terminal
l DC 12V terminal
• WK-3100
h
i j
OUT
MIDI
PHONES/
OUTPUT
k
l
SUSTAIN/
ASSIGNABLE JACK
DC 12V
IN
h PHONES/OUTPUT terminal
i MIDI OUT terminal
j MIDI IN terminal
k SUSTAIN/ASSIGNABLE JACK terminal
l DC 12V terminal
Rear Panel
Console
• WK-3100 only
m
n
n MIC VOLUME knob
m Card slot
E-13
735A-E-015C
WK3100_e_10-25.p65
13
04.3.26, 0:10 PM
General Guide
About the display
1
2 3
4
5
G r a n dPn o
15
14
13
12
11
10
9
8
7
6
1.
TONE/RHYTHM indicator
TONE is shown during tone selection and display, while RHYTHM is shown during rhythm selection and display.
2.
Tone/Rhythm number (number area)
Number of currently selected tone or rhythm. The TONE/RHYTHM indicator shows whether the number is a tone or rhythm.
This area also shows other information in other modes.
3.
Chord name display
Shows chord names while Auto Accompaniment is being used.
4.
Tone/Rhythm name (text area)
Name of currently selected tone or rhythm. The TONE/RHYTHM indicator shows whether the name is a tone or rhythm. This
area also shows other information in other modes.
5.
Octave symbol 1
One symbol indicates the note being produced by the keyboard is one octave higher than the note shown in the staff notation
area 6. Two symbols indicate two octaves higher.
6.
Staff notation area
Notes you play on the keyboard, notes played back from song memory, chord forms, and received MIDI data* are shown
here.
7.
Octave symbol 2
One symbol indicates the note being produced by the keyboard is one octave lower than the note shown in the staff notation
area 6.
8.
Indicators
An indicator appears to indicate that a function (Song Memory, SMF player, Auto Harmonize, Split, Layer) is currently in use.
9.
Beat number
Shows the beat number during rhythm and Auto Accompaniment play, and while the Song Memory and SMF Player are
turned on.
10.
Measure
Shows the measure number from the start of play during rhythm and Auto Accompaniment play, and while the Song Memory
and SMF Player are turned on.
11.
Tempo indicator
Shows the tempo as a value indicating the number of beats per minute during rhythm and Auto Accompaniment play, and
while the Song Memory is turned on. This display area also shows other information in other modes.
12.
Metronome
You can turn on the metronome to provide a reference beat for your keyboard play.
E-14
WK3100_e_10-25.p65
735A-E-016A
14
04.3.26, 0:10 PM
General Guide
13.
Level meter
The numbers 1 through 16 correspond to Mixer channels. The level meter indicates which channels are on and off, and also
indicates the volume level.
Drawbar Organ Mode
In the Drawbar Organ Editing Mode, the level meter shows the position of each drawbar and the status of each percussion
parameter.
14.
Graphic keyboard
Notes you play on the keyboard, notes played back from song memory, and received MIDI data* are indicated on the graphic
keyboard.
15.
Mode indicators
Pointers appear next to these mode names to indicate that the Transpose, Keyboard Settings, Mixer, Synth, Effect, or Disk/
Card mode is currently active.
* Any receive data outside the range of E1 to G7 is not displayed.
NOTE
• Display examples shown in this User’s Guide are intended for illustrative purposes only. The actual text and values that
appear on the display may differ from the examples shown in this User’s Guide.
• Due to LCD element characteristics, display contrast changes depending on the angle from which you view it. The initial
default contrast setting is one that allows easy viewing for a musician seated directly in front of the display. You can also
adjust the contrast to the level that suits your particular needs. For more information, see page E-82.
E-15
735A-E-017A
WK3100_e_10-25.p65
15
04.3.26, 0:10 PM
Power Supply
This keyboard can be powered by current from a standard
household wall outlet (using the specified AC adaptor) or by
batteries. Always make sure you turn the keyboard off
whenever you are not using it.
Using batteries
Always make sure you turn off the keyboard before loading
or replacing batteries.
To load batteries
1
2
Remove the battery compartment cover.
Load six D-size batteries into the battery
compartment.
• Make sure that the positive (+) and negative (–) ends
are facing correctly.
3
Insert the tabs on the battery compartment cover
into the holes provided and close the cover.
tab
Important Battery Information
■ The following shows the approximate battery life.
Alkaline batteries ............................. 4 hours
The above value is standard battery life at normal
temperature, with the keyboard volume at a medium
setting. Temperature extremes or playing at very loud
volume settings can shorten battery life.
■ Any of the following symptoms indicate low battery power.
Replace batteries as soon as possible whenever any of
the following occurs.
• Dim power indicator
• Instrument does not turn on
• Display that is flickering, dim, or difficult to read
• Abnormally low speaker/headphone volume
• Distortion of sound output
• Occasional interruption of sound when playing at high
volumes
• Sudden power failure when playing at high volumes
• Flickering or dimming of the display when playing at
high volume
• Continued sound output even after you release a key
• A tone that is totally different from the one that is
selected
• Abnormal rhythm pattern and demo tune play
• Abnormally low microphone volume (WK-3100 only)
• Distortion of microphone input (WK-3100 only)
• Dim power supply indicator when a microphone is used
(WK-3100 only)
• Sudden power failure when using the microphone
(WK-3100 only)
• Loss of power, sound distortion, or low volume when
playing from a connected computer or MIDI device
• Sudden power failure while reading from or writing to
a diskette (WK-3500 only)
WARNING
NOTE
• The keyboard may not function correctly if you load or
replace batteries with power turned on. If this happens,
turning the keyboard off and then back on again should
return functions back to normal.
Misuse of batteries can cause them to leak, resulting in
damage to nearby objects, or to explode, creating the risk of
fire and personal injury. Always make sure you observe the
following precautions.
• Never try to take batteries apart or allow them to
become shorted.
• Never expose batteries to heat or dispose of them by
incineration.
• Never mix old batteries with new ones.
• Never mix batteries of different types.
• Do not charge the batteries.
• Make sure the positive (+) and negative (–) ends of
the batteries are facing correctly.
CAUTION
Misuse of batteries can cause them to leak resulting in
damage to nearby objects, or to explode, creating the risk of
fire and personal injury. Always make sure you observe the
following precautions.
• Use only batteries that are specified for use with this product.
• Remove batteries from the product if you do not plan
to use it for a long time.
E-16
WK3100_e_10-25.p65
735A-E-018C
16
04.3.26, 0:10 PM
Power Supply
CAUTION
Using the AC Adaptor
Make sure that you use only the AC adaptor specified for
this keyboard.
Specified AC Adaptor: AD-12
AC adaptor AD-12
MIDI
OUT
IN
SUSTAIN/
ASSIGNABLE JACK
R
L/MONO
LINE OUT
DC 12V
AC outlet
Also note the following important warnings and precautions
when using the AC adaptor.
Misuse of the AC adaptor creates the risk of fire and electric
shock. Always make sure you observe the following
precautions.
• Do not locate the electric cord near a stove or other
sources of heat.
• Never pull on the cord when unplugging from the
electrical outlet. Always grasp the AC adaptor when
unplugging.
• Insert the AC adaptor into the wall outlet as far as it
will go.
• Unplug the AC adaptor from the wall outlet during
lightening storms or before leaving on a trip or other
long-term absence.
• At least once a year, unplug the AC adaptor from the
wall outlet and wipe away any dust that is built up in
the area around the prongs of the plug.
IMPORTANT!
WARNING
Misuse of the AC adaptor creates the risk of fire and electric
shock. Always make sure you observe the following
precautions.
• Be sure to use only the AC adaptor that is specified
for this product.
• Use only a power source whose voltage is within the
rating marked on the AC adaptor.
• Do not overload electrical outlets and extension cords.
• Never place heavy objects on the cord or subject it to
heat.
• Never try to modify the cord or subject it to excessive
bending.
• Never twist or stretch the cord.
• Should the electric cord or plug become damaged,
contact your original retailer or authorized CASIO
Service Provider.
• Never touch the AC adaptor while your hands are wet.
Doing so creates the risk of electric shock.
• Make sure that the keyboard is turned off before
connecting or disconnecting the AC adaptor.
• Using the AC adaptor for a long time can cause it to
become warm to the touch. This is normal and does not
indicate malfunction.
Auto Power Off
When you are using battery power, keyboard power turns
off automatically whenever you leave it on without
performing any operation for about 6 minutes. When this
happens, press the POWER button to turn power back on.
NOTE
• Auto Power Off is disabled (it does not function) when
you are using the AC adaptor to power the keyboard.
To disable Auto Power Off
Hold down the TONE button while turning on the keyboard
to disable Auto Power Off.
• When Auto Power Off is disabled, the keyboard does not
turn off automatically no matter how long it is left with no
operation being performed.
• Auto Power Off is automatically enabled whenever you
turn on keyboard power.
E-17
735A-E-019A
WK3100_e_10-25.p65
17
04.3.26, 0:10 PM
Power Supply
Settings
Saving Setups and Memory Contents
Tone, rhythm, and other “main keyboard settings” in effect
when you turn off the keyboard manually by pressing
POWER button or when Auto Power Off turns off power are
still in effect the next time you turn power back on.
Main Keyboard Settings
Tone number, layer, split, split point, drawbar organ
tone settings, transpose, tuning, and contrast settings,
touch response, reverb, chorus, DSP, equalizer, rhythm
number, tempo, keyboard channel, MIDI In Chord
Judge on/off, accomp MIDI out on/off, assignable
jack setting, accompaniment volume, user area tones
(Synthesizer Mode), user area accompaniments, user
DSP area, pitch bend range, Auto Harmonize on/off,
Auto Harmonize type, Mixer hold, DSP hold, Auto
Accompaniment mode, all Mixer parameters, all
Synthesizer Mode parameters, Song Memory song
numbers, SMF player settings (play mode, manual
play part, SMF playback volume)
Turning Off the Keyboard
• Be sure to press the POWER button to turn off power and
make sure that the LCD backlight is off before disconnecting
the AC adaptor or doing anything else.
• Never disconnect the AC adaptor while the keyboard is
turned on or try to turn off power using any other technique
besides pressing the POWER button. Doing so can cause
the contents of the keyboard’s Flash memory to become
corrupted. Strange keyboard operation and abnormal
startup when power is turned on are symptoms of
corrupted Flash memory contents. See “Troubleshooting”
on page E-106 for more information.
About Flash memory
Your keyboard comes with built-in Flash memory, which can
continue to hold data even when electrical power is totally
cut off. This means that even after batteries go completely
dead, you can attach the AC adaptor, turn on power, and still
recall data stored in memory.
You can back up keyboard memory contents and other data
using the media described below.
• SmartMediaTM Card
See “Using a SmartMedia Card” on page E-93.
• Floppy Diskette (WK-3500 only)
See “Using the Floppy Disk Drive (WK-3500 Only)” on page
E-94.
IMPORTANT!
• When running under battery power, be sure to replace
batteries as soon as possible after the first signs of low
battery power (dim power indicator lamp, dim display
characters, etc.) Though the keyboard’s Flash memory
is non-volatile (which means that data is not lost when
power is interrupted), data can be lost if power suddenly
fails while data is being written to flash memory*.
* While storing or deleting user data, while recording
with the synthesizer, while transferring data from a
computer, etc.
Initializing the Keyboard
Use the procedure on page E-80 to initialize the keyboard,
which clears all memory data and returns settings to their
initial factory defaults.
IMPORTANT!
• Never press the POWER button while the following
message is on the keyboard’s display.
(message) “Pls Wait” or “Bulk In”
Turning off the keyboard while the above message is
on the display can cause user data (user tones, song
memory data, etc.) currently stored in keyboard memory
or on external media to become corrupted. Once
corrupted, you may not be able to recall the data again.
Memory Contents
In addition to the above settings, data stored in the
Registration Mode and Song Memory Mode is also retained
when keyboard power is turned off.
E-18
WK3100_e_10-25.p65
735A-E-020A
18
04.3.26, 0:10 PM
Connections
Connecting to a Musical Instrument Amplifier 3
• WK-3500
Before connecting phones or other external equipment, be
sure to first turn down the volume settings of the keyboard
and the connected equipment. You can then adjust volume
to the desired level after connections are complete.
Use commercially available cords to connect to the two jacks
as shown in Figure 3. It is up to you to purchase connecting
cables like the ones shown in the illustration for connection.
Use the keyboard’s VOLUME knob to adjust the volume level.
• If your amplifier has only one input jack, connect a cord to
the L/MONO jack only.
[Front]
NOTE
Phones and Line Out Terminals
• You can also connect the keyboard’s MIDI terminal to a
computer or sequencer. See “MIDI” on page E-89 for
details.
PHONES Terminal
1
Stereo standard plug
Connecting Phones 1
Connecting phones cuts off output from the keyboard’s builtin speakers, so you can play even late at night without
disturbing anyone.
[Rear Panel]
Audio amplifier AUX IN, etc.
PIN plug
LEFT
(White)
RIGHT
(Red)
MIDI
OUT
Guitar amplifier,
keyboard amplifier, etc.
IN
SUSTAIN/
ASSIGNABLE JACK
R
L/MONO
LINE OUT
DC 12V
Standard jacks
Standard plugs
INPUT 1
INPUT 2
Connecting to Audio Equipment 2
Use commercially available cords to connect to the two jacks
as shown in Figure 2. It is up to you to purchase connecting
cables like the ones shown in the illustration for connection.
Normally in this configuration, you must set the audio
equipment’s input selector to the setting that specifies the
terminal (such as AUX IN) that the keyboard is connected to.
Use the keyboard’s VOLUME knob to adjust the volume level.
E-19
735A-E-021A
WK3100_e_10-25.p65
19
04.3.26, 0:10 PM
Connections
• WK-3100/WK-3000
NOTE
Phones/Output Terminal
Before connecting phones or other external equipment, be
sure to first turn down the volume settings of the keyboard
and the connected equipment. You can then adjust volume
to the desired level after connections are complete.
WK-3100
[Rear Panel]
• Be sure to use a connecting cord that has a stereo
standard plug on the end you connect to the keyboard,
and a connector that provides dual channel (left and
right) input to the amplifier to which you are connecting.
The wrong type of connector at either end can cause
one of the stereo channels to be lost.
• When connected to a musical instrument amplifier, set the
volume of the keyboard to a relatively low level and make
output volume adjustments using the amplifier’s controls.
PHONES/OUTPUT Terminal
Audio connection
PHONES/
OUTPUT
Connection Example
1
PIN plug (red)
Stereo standard
plug
3
INPUT 1
INPUT 2
PIN plug (white)
Stereo standard plug
Keyboard amp,
guitar amp, etc.
PIN jack
To keyboard’s
PHONES/OUTPUT
terminal
White
2
Red
PIN plug
Standard plug
Keyboard or
guitar amp
LEFT RIGHT
AUX IN or similar terminal
of audio amplifier
NOTE
• You can also connect the keyboard to a computer or
sequencer. See “MIDI” on page E-89 for details.
WK-3000
[Front]
PHONES/OUTPUT Terminal
Audio connection
Sustain/Assignable jack Terminal
1
You can connect an optional sustain pedal (SP-3 or SP-20) to
the SUSTAIN/ASSIGNABLE JACK terminal to enable the
capabilities described below.
Stereo standard
plug
3
Keyboard amp,
guitar amp, etc.
White
2
Red
PIN plug
For details on how to select the pedal function you want, see
“Changing Other Settings” on page E-79.
LEFT RIGHT
AUX IN or similar terminal
of audio amplifier
SUSTAIN/ASSIGNABLE JACK Terminal
MIDI
Connecting Phones 1
Connecting phones cuts off output from the keyboard’s builtin speakers, so you can play even late at night without
disturbing anyone.
OUT
IN
SUSTAIN/
ASSIGNABLE JACK
R
L/MONO
LINE OUT
DC 12V
Audio Equipment 2
Connect the keyboard to a audio equipment using a
commercially available connecting cord with a standard plug
on one end and two PIN plugs on the other end. Note that
the standard plug you connect to the keyboard must be a
stereo plug, otherwise you will be able to output only one of
stereo channels. In this configuration, you normally set the
input selector of the audio equipment to the terminal (usually
marked AUX IN or something similar) where the cord from
the keyboard is connected. See the user documentation that
comes with your audio equipment for full details.
SP-20
Sustain Pedal
• With piano tones, depressing the pedal causes notes to
linger, much like a piano’s damper pedal.
• With organ tones, depressing the pedal causes notes to
continue to sound until the pedal is released.
Musical Instrument Amplifier 3
Use a commercially available connecting cord to connect the
keyboard to a musical instrument amplifier.
E-20
WK3100_e_10-25.p65
735A-E-022C
20
04.3.26, 0:10 PM
Connections
Sostenuto Pedal
• As with the sustain pedal function described above,
depressing the sostenuto pedal causes notes to be sustained.
• This difference between a sostenuto and sustain pedal is
the timing. With a sostenuto pedal, you press the keys and
then depress the pedal before you release the keys. Only
the notes that are sounding when the pedal is depressed
are sustained.
IMPORTANT!
• Be sure to use the microphone’s ON/OFF switch to turn
off the microphone and to disconnect the microphone
from the keyboard whenever you are not using it.
Recommended Microphone Type
• Dynamic microphone (standard plug)
Soft Pedal
Depressing the pedal softens the sound of the notes being
played.
Rhythm Start/Stop Pedal
In this case, the pedal performs the same functions as the
START/STOP button.
Using the microphone jack
(WK-3100 only)
Connecting a commercially available microphone* to the MIC
IN jack makes it possible to sing as you play, or sing with
accompaniment from Song Memory or SMF playback. When
connecting a microphone, be sure to first adjust the MIC
VOLUME to a relatively low setting, and then adjust to the
level you want after connecting.
* If a microphone was included with your keyboard, use that
microphone. If your keyboard did not come with a
microphone, use a commercially available microphone that
satisfies the stipulated specifications.
1
2
3
Set the MIC VOLUME knob setting so it is on the
“MIN” side.
Turn on the microphone’s ON/OFF switch.
Use the MIC VOLUME knob to adjust microphone
volume to the level you want.
MIC IN jack
IMPORTANT!
• Connection to the MIDI terminal of an external device
can cause static in the microphone signal. Use of a
Cannon type microphone with a metal-shielded body
helps to prevent static.
• Be sure to disconnect the microphone from the keyboard
whenever you are not using it.
Howling (Feedback Noise)
Any of the following conditions can cause howling (feedback
noise).
• Covering the head of the microphone with your hand
• Positioning the microphone too near to a speaker
Should howling occur, try grasping the microphone further
away from the head, and move away from any nearby
speaker.
Static Noise
Fluorescent lighting can cause static noise in the microphone
signal. When this happens, move away from the lighting you
suspect may be causing the static.
NOTE
• Effects are not applied to microphone input.
Accessories and Options
Use only the accessories and options specified for this
keyboard. Use of non-authorized items creates the danger of
fire, electrical shock, and personal injury.
Microphone ON/OFF switch
Microphone
MIC VOLUME knob
E-21
735A-E-023C
WK3100_e_10-25.p65
21
04.3.26, 0:10 PM
Basic Operations
POWER
TONE
Number buttons
VOLUME
This section provides information on performing basic
keyboard operations.
Drawbar Organ Tones: 50 Preset Tones + 100 User Tones
Number
To play the keyboard
1
2
Press the POWER button to turn the keyboard on.
Number
of Tones
Tone Type
DSP Line
On/Off*1
000 - 049
50
Preset Tones
On/Off*5
100 - 199
100
User Tones*6
On/Off*3
For details about drawbar organ tones, see “Using the
Drawbar Organ Mode” on page E-26.
*1: See “Changing Tones and Configuring DSP Effect
Settings” on page E-23.
*2: Memory area for tones created by you. See “Synthesizer
Mode” on page E-51. User tone areas 600 through 699
initially contain the same data as DSP types 000 through
099.
*3: Depends on source tone or user setting. See “Synthesizer
Mode” on page E-51 for more information.
*4: Area for data transferred from a computer. See “Using
the Data Downloard Service” on page E-91 for more
information. For information about waveforms, see
“Creating a User Tone” on page E-54.
*5: Depends on tone. This status can be checked by viewing
the DSP button. See “About the DSP Button” on page E34 for more information.
*6: Memory area for tones created by you. See “To edit a
drawbar organ tone” on page E-28. User drawbar organ
tone areas initially contain two sets of the same data as
drawbar organ tones types 000 through 049.
Tone Types
NOTE
3
Use the VOLUME knob to set the volume to a
relatively low level.
Play something on the keyboard.
Selecting a Tone
This keyboard comes with tones built-in, as shown below.
A partial list of the available tone names is printed on the
keyboard console. See the “Tone List” on page A-1 of this
manual for a complete list. “Advanced Tones”, are variations
of standard tones, which are created by programming in
effects (DSP) and other settings.
Standard Tones: 516 Preset Tones + 124 User Tones
DSP Line
On/Off*1
Number
Number
of Tones
000 - 299
300
Advanced Tones
On
300 - 499
200
Preset Tones
Off
500 - 515
16
Drum Sets
600 - 699
100
User Tones*2
On/Off*3
700 - 719
20
User Tones with Waves*4
On/Off*3
800 - 803
4
User Drum Sets with
Waves*4
On/Off*5
Tone Type
Off
• You cannot select tone numbers not included in the
above range (standard tones 516 through 599 and 720
through 799, and drawbar organ tones from 050 to 099).
When you use the [+] and [–] buttons to scroll through
tone numbers, scrolling jumps across the unused
numbers. Pressing [+] when 515 is selected, for
example, jumps to 600.
E-22
WK3100_e_10-25.p65
735A-E-024A
22
04.3.26, 0:10 PM
Basic Operations
Digital Sampling
To select a tone
1
2
3
Find the tone you want to use in the tone list and
note its tone number.
Press the TONE button.
Use the number buttons to input the three digit tone
number for the tone you want to select.
Example: To select “332 ACOUSTIC BASS GM”, input
3, 3 and then 2.
A c o . B s _G
NOTE
• Always input all three digits for the tone number,
including leading zeros (if any).
• You can also increment the displayed tone number by
pressing [+] and decrement it by pressing [–].
• When one of the drum sets is selected (tone numbers
500 through 515), each keyboard key is assigned a
different percussion sound. See page A-12 for details.
A number of the tones that are available with this keyboard
have been recorded and processed using a technique called
digital sampling. To ensure a high level of tonal quality,
samples are taken in the low, mid, and high ranges and then
combined to provide you with sounds that are amazingly
close to the originals. You may notice very slight differences
in volume or sound quality for some tones when you play
them at different positions on the keyboard. This is an
unavoidable result of multiple sampling, and it is not a sign
of malfunction.
Changing Tones and Configuring
DSP Effect Settings
This keyboard has only a single DSP sound source. Because
of this, selecting tones for which DSP is enabled for multiple
parts when layering or splitting tones (page E-74, 75) can
cause conflicts. To avoid conflicts, DSP is allocated to the last
DSP enabled tone, and DSP is disabled (DSP line OFF) for all
other parts.
DSP line is a parameter that controls whether or not the
currently selected DSP effect is applied to a part.* Each tone
has a DSP line parameter. Selecting a tone for a part applies
the tone’s DSP line parameter setting to all parts.
* The DSP line parameter is turned on (DSP effect is applied)
for the 300 Advanced Tones numbered 000 through 299,
and turned off (DSP effect not applied) for the 200 preset
tones from 300 to 499. For information about other tones,
see “Tone Types” on page E-22.
Polyphony
The term polyphony refers to the maximum number of notes
you can play at the same time. The keyboard has 32-note
polyphony, which includes the notes you play as well as the
rhythms and auto-accompaniment patterns that are played
by the keyboard. This means that when a rhythm or autoaccompaniment pattern is being played by the keyboard, the
number of notes (polyphony) available for keyboard play is
reduced. Also note that some of the tones offer only 10-note
polyphony.
E-23
735A-E-025A
WK3100_e_10-25.p65
23
04.3.26, 0:10 PM
Basic Operations
●WK-3500
PIANO SETTING
●WK-3100/WK-3000
MODULATION button
PITCH BEND wheel
MODULATION wheel
PITCH BEND wheel
PIANO SETTING Button
Pressing this button changes the setup of the keyboard to
optimize it for piano play.
Settings
Tone Number: “000 St.GrPno”
Rhythm Number: “120 Pf Bld 1”
Accompaniment Mode: Normal
Layer: Off
Split: Off
Auto Harmonize: Off
Transpose: 0
Touch Response:
Off: Returns to initial default
On: No change
Assignable Jack: SUS
Local Control: On
Mixer Channel 1 Parameter Setup: Depends on tone
NOTE
• Pressing the PIANO SETTING button while a rhythm is
playing stops rhythm play and then changes the
keyboard setup.
• Pressing the PIANO SETTING button while the keyboard
is in the Synthesizer Mode or other mode exits the
current mode and then changes the keyboard setup.
• The setup of the keyboard does not change if you press
the PIANO SETTING button when any one of the
following exists.
* During real-time recording, step recording, or while
using the editing function of the Song Memory
* While the data save or overwrite message is on the
display
* During a registration data save operation
To optimize keyboard settings for
piano play
1
2
Press the PIANO SETTING button.
Now try playing something on the keyboard.
• The notes you play will sound with a piano tone.
• If you want to play with rhythm accompaniment,
press the START/STOP button. This causes a rhythm
that is optimized for piano will start to play.
• To stop rhythm play, press the START/STOP button
again.
E-24
WK3100_e_10-25.p65
735A-E-026C
24
04.3.26, 0:10 PM
Basic Operations
Using the PITCH BEND Wheel
Using the MODULATION
As its name suggests, the PITCH BEND wheel lets you “bend”
the pitch of a sound. This makes it possible to add a touch of
realism to saxophone and other tones.
Modulation applies vibrato, which modulates the pitch of a
note. It works best with notes that are sustained (held) by
keeping a keyboard key held down, especially when playing
the melody with a violin or other similar tone.
You can modify the modulation effect using DSP parameter
0 through 7. For more information, see “DSP Parameters” on
page E-33.
To use the PITCH BEND wheel
1
While holding down a keyboard key with your right
hand, use your left hand to rotate the PITCH BEND
wheel up and down.
• Releasing the PITCH BEND wheel returns the note
to its original pitch.
• WK-3500
To use the MODULATION Wheel
1
NOTE
• With saxophone and electrical guitar tones, the most
realistic sounding effects can be produced if you play
notes and operate the PITCH BEND wheel
simultaneously.
• See “Pitch Bend Range (Initial Default: 12)” on page E82 for changing the bend range of the PITCH BEND
wheel.
• Never turn on keyboard power while the PITCH BEND
wheel is rotated.
While playing melody notes with your right hand,
rotate the MODULATION wheel with your left
hand to apply vibrato to the notes.
• The amount of vibrato applied depends on how far
you rotate the MODULATION wheel upwards.
Setting the wheel to its neutral position (rotated as
far downwards as it can go) turns vibrato off.
• WK-3100/WK-3000
To use the MODULATION button
1
While holding down a keyboard key with your right
hand, use your left hand to press the
MODULATION button.
• Vibrato is applied as long as the MODULATION
button is depressed.
NOTE
• Modulation can be used to add greater expression to
sustained melody notes being played using a violin,
synthetic reed, or other similar tone.
• Modulation affects different tones in different ways.
E-25
735A-E-027C
WK3100_e_10-25.p65
25
04.3.26, 0:10 PM
Using the Drawbar Organ Mode
Your keyboard has built-in “drawbar organ tones” that can be altered using nine digital drawbars whose operations are similar to
the controls on a drawbar organ. You can also select percussion or key click. There is room in memory for storage of up to 100
user-created drawbar tone variations.
Drawbar Organ Mode Operational Flow
Tone/Rhythm Selection Screeen*
DRAWBAR ORGAN button
EXIT button
Drawbar Organ Tone Selection Screen
[왘] CURSOR button
DRAWBAR ORGAN button
Drawbar Organ Tone Editing Screen
[왗] / [왘] CURSOR buttons
[왗] / [왘] CURSOR buttons
“More?” Screen
[왔] CURSOR button
[왖] CURSOR button
Synthesizer Editing Screen
[왔] CURSOR button
[왖] CURSOR button
DSP Effect Editing Screen
[왔] CURSOR button
[왖] CURSOR button
Name/Save Setting Screen
* You can also display the drawbar organ tone selection screen from the Song Memory Mode or SMF Playback Mode screen. In
this case, however, the Drawbar Organ Tone Editing Screen does not appear.
E-26
WK3000_e_26-37.p65
735A-E-028A
26
04.3.26, 0:10 PM
Using the Drawbar Organ Mode
Channel Buttons while the Drawbar Organ Tone Selection Screen is Displayed
The 18 buttons along the bottom of the display function as drawbar buttons while the drawbar organ tone selection screen is on
the display (after you press the DRAWBAR ORGAN button). Each pair of buttons (upper and lower) represents a drawbar, which
means that the 18 buttons provide you with the function of nine drawbars.
“ ’ ”: Feet
Value
Parameter Name
F t 16 ’
Currently selected
parameter
16 51/3
8
4
2 2 /3
2
13/5 11/3
1
CLICK SECOND THIRD DECAY
PERCUSSION
Decrease
Currently selected drawbar
Increase
Drawbar buttons
Each of the nine button pairs is assigned values ranging from 16 feet to 1 foot. Each button pair has a decrease button (for
decreasing by 16 feet, 5-1/3 feet, etc.) and an increase button (for increasing by 16 feet, 5-1/3 feet, etc.).
E-27
735A-E-029A
WK3000_e_26-37.p65
27
04.3.26, 0:10 PM
Using the Drawbar Organ Mode
DRAWBAR ORGAN
Number buttons
[+]/[–]
CURSOR
To select a drawbar organ tone
1
2
Parameter Setting
Find the drawbar organ tone you want to use in
the tone list and note its tone number.
Parameter Name
F t 16 ’
Press the DRAWBAR ORGAN button.
• This causes the drawbar organ tone selection screen
to appear.
Tone Number
Tone Name
• There are a total of 13 parameters. You can use the
[왗] and [왘] CURSOR buttons to cycle through them.
See “Parameter Details” on page E-29 for more
information.
• While the “More?” screen is on the display, you can
advance to the synthesizer and DSP effect editing
screens by pressing the [왔] CURSOR button or the
[+] button.
Ro c kO r g 1
3
Use the number buttons to input the three digit tone
number for the tone you want to select.
NOTE
• Always input all three digits for the tone number,
including leading zeros (if any).
• You can also increment the displayed tone number by
pressing [+] and decrement it by pressing [–].
3
Use the [왖] and [왔] CURSOR buttons or the [+]
and [–] buttons to change the setting of the currently
displayed parameter.
• You can also change a parameter setting by entering
a value with the number buttons.
• You can monitor the changes in a tone by playing
notes on the keyboard as you adjust parameter
settings.
NOTE
To edit a drawbar organ tone
1
2
Select the drawbar organ tone (000 to 049, 100 to
199) you want to edit.
Use the [왗] and [왘] CURSOR buttons to display
the drawbar organ tone editing screen. Select the
parameter whose setting you want to change.
• Selecting a different tone after you edit parameters
replaces parameter settings with those of the newly
selected tone.
• If you have drawbar organ tones assigned to more than
one channel, changing the drawbar organ setting for one
of the channels causes the same setting to be applied
to all of the other channels as well.
• See “To save an edited drawbar organ tone” on page E30 for information about saving your edits.
Example: Selecting the “Ft16’” parameter
E-28
WK3000_e_26-37.p65
735A-E-030A
28
04.3.26, 0:10 PM
Using the Drawbar Organ Mode
Editing Synthesizer Mode Parameters
and DSP Parameters of Drawbar Tones
As with standard (non-drawbar) tones, you can edit the
Synthesizer Mode parameters and DSP parameters of
drawbar organ tones. See “Drawbar Organ Mode Operational
Flow” on page E-26.
1
Use the [왗] and [왘] CURSOR buttons to display
“More?”, and then press the [왔] CURSOR button.
• This enters the Synthesizer Mode, which is indicated
by the indicator next to SYNTH on the display screen.
• For the remainder of this procedure, perform the steps
starting from step 3 under “Creating a User Tone” on
page E-54.
Percussion
This parameter lets you add percussion sound, which
provides modulation to sustained tones that you create. When
you hold down a key on the keyboard, the sound produced
decays until it is no longer audible. Pressing the key again
sounds the note again at a louder volume. Percussion has
“2nd Percussion” (2nd overtone pitch) and “3rd Percussion”
(3rd overtone pitch) settings, each of which can be turned on
or off.
You can also specify the percussion decay time, which controls
how long it takes for the percussion sound to decay.
Parameter Name
Parameter Display
Indication
2nd Percussion
Second
oFF .... Click Off
on ....... Click On
3rd Percussion
Third
oFF .... Off
on ....... On
Percussion
Decay Time
Decay
000 to 127
Parameter Details
The following provides details about the parameters you can
configure using the drawbar organ tone editing screen.
Settings
Drawbar Position
This parameter defines the position of each drawbar, and the
volume of each overtone. The larger the value, the greater
the corresponding overtone’s volume.
Parameter Name
Parameter Display
Indication
Settings
Drawbar 16’
Ft 16’
0 to 3
Drawbar 5 1/3’
Ft 5 1/3’
0 to 3
Drawbar 8’
Ft 8’
0 to 3
Drawbar 4’
Ft 4’
0 to 3
Drawbar 2 2/3’
Ft 2 2/3’
0 to 3
Drawbar 2’
Ft 2’
0 to 3
Drawbar 1 3/5’
Ft 1 3/5’
0 to 3
Drawbar 1 1/3’
Ft 1 1/3’
0 to 3
Drawbar 1’
Ft 1’
0 to 3
(Ft: Feet)
Click
The parameter determines whether or not a key click is added
when a sustained tone configured using the drawbars is
played.
Parameter Name
Click
Parameter Display
Indication
Settings
oFF .... Click Off
on ....... Click On
Click
E-29
735A-E-031B
WK3000_e_26-37.p65
29
04.3.26, 0:10 PM
Using the Drawbar Organ Mode
[+]/[–]
CURSOR
Display Contents in the Drawbar Organ Mode
In the Drawbar Organ Mode, the current status of the drawbar
positions, key click, and percussion parameters are indicated
on the display’s bar graph as shown in the illustrations below.
There is one line for each parameter, and the bottom segment
of the selected parameter line flashes.
The bottom segment of the bar graph column that represents
the currently selected parameter flashes to indicate that it is
selected.
None of the channel numbers (1 to 16) are displayed in the
drawbar organ tone mode and editing mode.
To save an edited drawbar organ
tone
1
2
3
Drawbar Position Graph
Setting Value
0
1
2
3
4
Click and Percussion On/Off Graph
On
5
Display
Percussion Decay Time Graph
Setting Value
0-31
32-63
64-95
Display
96-127
Use the [+] and [–] buttons to select a tone number.
After the tone name is the way you want, press the
[왘] CURSOR button to store the tone.
• Use the [+] and [–] buttons to scroll through letters at
the current cursor location.
• Use the [왗] and [왘] CURSOR buttons to move the
cursor left and right.
• See the page E-103 for information about inputting
text.
Off
On
Blink
Off
Press the [왔] CURSOR button three times to display
the screen for inputting a tone name and assigning
a tone number.
• You can select a tone number in the range of 100 to
199.
Display
Setting Value
After editing parameters, use the [왗] and [왘]
CURSOR buttons to display “More?”.
After everything is the way you want, press the [왔]
CURSOR button to store the tone.
• This will display a confirmation message asking
whether you really want to save the data. Press the
YES button to save the data.
• After the save operation is complete, the message
“Complete” appears and then the display returns to
the tone selection or rhythm selection screen.
• To cancel save, press the EXIT button.
E-30
WK3000_e_26-37.p65
735A-E-032A
30
04.3.26, 0:10 PM
Applying Effects to Tones
DSP
DSP effects are applied to the connection between the sound
source and output. You can select distortion and modulation
effects. You can create DSP effect setups and also transfer
downloaded DSP data from your computer. The keyboard
has memory that lets you store up to 100 DSP effect setups.
See “Using the Data Download Service” on page E-91 and
“Saving the Settings of DSP Parameters” on page E-33 for
more information.
This keyboard provides you with a selection of effects that
you can apply to tones.
The built-in effects include a wide variety of variations that
give you access to a selection of general digital effects.
Effect Blocks
The following shows how the effects of this keyboard are
organized.
REVERB
Reverb simulates the acoustics of specific types of
environments. You can choose from among 16 different reverb
effects, including “Room” and “Hall”.
REVERB
DSP button
CHORUS
Sound Source
16ch
EQUALIZER
off
on
Output
DSP
CHORUS
The chorus effect gives sound greater depth by causing it to
vibrate. You can choose from among 16 different chorus
effects, including “Chorus” and “Flanger”.
DSP Line
EQUALIZER
The equalizer is another type of effect that you can use to
make adjustments in tone quality. Frequencies are divided
among a number of bands, and raising and lowering the level
of each frequency band alters the sound.
You can reproduce the optimal acoustics for the type of music
you are playing (classics, for example) by selecting the
applicable equalizer setting.
Channel Buttons while the Effect Mode Screen is Displayed
In the Effect Mode, the 18 buttons along the bottom of the display screen control the type and parameters of each effect, a shown
in the illustration below.
Effect type
Parameter 1
Parameter 0
16
51/3
8
Parameter 3
Parameter 5
Parameter 2
Parameter 4
4
2
22/3
Parameter 7
Parameter 6
13/5 11/3
1
Decrease
Currently selected drawbar
Increase
CHANNEL buttons
NOTE
• Pressing the [왖] and [왔] CURSOR buttons at the same time returns the currently selected effect to its preset value.
E-31
735A-E-033A
WK3000_e_26-37.p65
31
04.3.26, 0:10 PM
Applying Effects to Tones
EFFECT
CURSOR
Number buttons
[+]/[–]
EXIT
Selecting a DSP Type
In addition to the 100 built-in effect types, you can also edit
effect types to create your own and store them in user
memory. You can have up to 100 effect types in user memory
at one time. You can also select the DSP type of the last DSP
enabled tone that you used. This means you always have
access to the DSP type of Advanced Tones and tones you
download over the Internet. To select the DSP type of the last
DSP enabled tone that you used, select “ton” in step 3 of the
procedure below.
Perform the following steps to select a DSP type.
Changing the Settings of DSP
Parameters
You can control the relative strength of a DSP and how it is
applied. See the following section titled “DSP Parameters”
for more information.
1
• This displays the parameter setting screen.
2
PREPARATION
• When using a DSP effect, you should use the Mixer to
confirm that the DSP lines of the required parts are
turned on. See “Mixer Function” on page E-47 for more
information.
After selecting the DSP type you want, use the [왗]
and [왘] CURSOR buttons to display the parameter
whose setting you want to change.
Use the [+] and [–] buttons or the number buttons
to make the parameter setting you want.
• Pressing the [+] and [–] buttons at the same time
returns the parameter to its recommended setting.
3
Press the EFFECT or EXIT button.
• This exits the tone or rhythm setting screen.
1
2
Press the EFFECT button so the pointer appears next
to EFFECT on the display.
Press the [왘] CURSOR button.
• The DSP type setting screen will appear automatically
about fives seconds after you press the button.
3
Use the [+] and [–] buttons or number buttons to
select the type of DSP you want.
• See the “Effect List” on page A-17 for information
about the DSP types that can be selected.
• Here you could also change the parameters of the
effect you selected, if you want. See “Changing the
Settings of DSP Parameters” for more information.
NOTE
• The DSP type display area shows the DSP number (000
to 199), or “ton” (user tone created using DSP).
E-32
WK3000_e_26-37.p65
735A-E-034A
32
04.3.26, 0:10 PM
Applying Effects to Tones
DSP Parameters
The following describes the parameters for each DSP.
Saving the Settings of DSP
Parameters
You can save up to 100 modified DSPs in the user area for
later recall when you need them.
DSP
■ Parameter 0 to 7
These parameters differ in accordance with the algorithm*
of the selected DSP type. See the “Effect List” on page A17 and the “DSP Algorithm List” on page A-19 for more
information.
* Effector structure and operation type
NOTE
• User DSP areas 100 through 199 initially contain the
same data as DSP types 000 through 099.
1
■ DSP Reverb Send (Range: 000 to 127)
• This causes the DSP number of the user area where
the DSP will be saved to flash on the display.
Specifies how much of the post-DSP sound should be sent
to reverb.
■ DSP Chorus Send (Range: 000 to 127)
2
Specifies how much of the post-DSP sound should be sent
to chorus.
NOTE
• Whether or not an effect is applied to the parts that are
sounding also depends on Mixer Mode Reverb Send,
Chorus Send, and DSP on/off settings. See “Mixer
Function” on page E-47 for more information.
• Playing a demo tune (page E-12) automatically changes
the effect to the one that is assigned to the tune. You
cannot change or cancel a demo tune effect.
• Changing the effect setting while sound is being output
by the keyboard causes a slight break in the sound when
the effect changes.
• A number of tones, called “Advanced Tones”,
automatically turn on the DSP line for richer, higher
quality sound. If you assign an Advanced Tone to a
keyboard part (Channels 1 through 4), the DSP line turns
on automatically and the DSP selection changes in
accordance with the settings of the Advanced Tone. Also,
the Mixer Mode DSP line on/off setting for the keyboard
part to which the Advanced Tone is assigned is turned
on.*
* The Mixer DSP line setting is automatically turned off
for each part that does not have an Advanced Tone
assigned.
Because of this, DSP effects previously applied to
these parts are cancelled, which can make their tone
sound different. In this case, display the Mixer screen
and turn DSP back on.
After making the DSP parameter settings you want,
press the [왔] CURSOR button.
Use the [+] and [–] buttons to select the user DSP
area number where you want to save the new DSP.
• You can select a user DSP area number in the range of
100 to 199 only.
3
After the user DSP area number you want is
selected, press the [왘] CURSOR button.
• Use the [+] and [–] buttons to scroll through letters at
the current cursor location.
• Use the [왗] and [왘] CURSOR buttons to move the
cursor left and right.
• See the page E-103 for information about inputting
text.
4
After everything is the way you want, press the [왔]
CURSOR button to store the effect.
• This will display a confirmation message asking
whether you really want to save the data. Press the
YES button to save the data.
• The message “Complete” appears momentarily on the
display, followed by the tone or rhythm selection
screen.
E-33
735A-E-035B
WK3000_e_26-37.p65
33
04.3.26, 0:10 PM
Applying Effects to Tones
EFFECT
DSP
CURSOR
Number buttons
[+]/[–]
EXIT
About the DSP Button
Selecting REVERB
Checking the DSP button will tell you whether or not DSP is
enabled for the tone that is currently selected for a part. The
DSP button will be lit for a tone that is DSP enabled (DSP
line ON), and unlit for a tone that is DSP disabled (DSP line
OFF). For example, when you move each part while using
the split/layer function, the DSP button lights or goes out in
accordance with that parts setting.
Perform the following steps to select REVERB.
1
Press the EFFECT button, so the pointer appears
next to EFFECT on the display screen.
Pressing the DSP button toggles the tone of the part you are
currently playing on the keyboard between enabled (DSP line
ON) and disabled (DSP line OFF).
To turn DSP line on and off
1
Press the DSP button to toggle DSP line for the
currently selected part on and off.
Pointer
2
Press the [왔] CURSOR button once.
• This displays the reverb editing screen.
3
Press the [왘] CURSOR button.
• The reverb type setting screen will appear
automatically about fives seconds after you press the
button.
4
Use the [+] and [–] buttons or the number buttons
to scroll through the reverb types until the one you
want is displayed, or use the number buttons to
input the reverb number you want to select.
• See the list on page A-17 for information about the
types of REVERB effects that are available.
• Here you could also change the parameters of the
effect you selected, if you want. See “Changing the
Settings of REVERB Parameters” for more
information.
E-34
WK3000_e_26-37.p65
735A-E-036B
34
04.3.26, 0:10 PM
Applying Effects to Tones
Changing the Settings of REVERB
Parameters
You can control the relative strength of a reverb and how it is
applied. See the following section titled “REVERB
Parameters” for more information.
1
After selecting the reverb type you want, use the
[왗] and [왘] CURSOR buttons to display the
parameter whose setting you want to change.
• This displays the parameter setting screen.
Example: To set the Reverb Time parameter
SR v T i me
2
3
Use the [+] and [–] buttons or the number buttons
to input the parameter setting you want.
Press the EFFECT or EXIT button.
• This returns to the tone or rhythm selection screen.
REVERB Parameters
Reverb effects are associated with either a reverb type or delay
type. Parameter settings depend upon the associated type.
Reverb Type (No. 0 to 5, 8 to 13)
■ Reverb Level (Range: 000 to 127)
Controls the reverb size. A larger number produces larger
reverb.
■ Reverb Time (Range: 000 to 127)
Controls how long reverb continues. A larger number
produces longer reverb.
■ ER Level (Initial Echo Sound) (Range: 000 to 127)
This parameter controls the initial reverb volume. The
initial echo sound is the first sound reflected from the
walls and ceiling when a sound is output by this keyboard.
A larger value specifies a larger echo sound.
■ High Damp (Range: 000 to 127)
Adjusts the damping of high frequency reverberation
(high sound). A smaller value damps high sounds,
creating a dark reverb. A larger value does not damp high
sounds, for a brighter reverb.
Delay Type (No. 6, 7, 14, 15)
■ Delay Level (Range: 000 to 127)
Specifies the size of the delay sound. A higher value
produces a larger delay sound.
■ Delay Feedback (Range: 000 to 127)
Adjusts delay repeat. A higher value produces a greater
number of repeats.
■ ER Level
Same as Reverb Type
■ High Damp
Same as Reverb Type
NOTE
• Whether or not an effect is applied to the parts that are
sounding also depends on Mixer Mode Reverb Send,
Chorus Send, and DSP on/off settings. See “Mixer
Function” on page E-47 for more information.
E-35
735A-E-037A
WK3000_e_26-37.p65
35
04.3.26, 0:10 PM
Applying Effects to Tones
EFFECT
CURSOR
Number buttons
[+]/[–]
EXIT
Selecting CHORUS
Perform the following steps to select CHORUS.
1
2
Press the EFFECT button, so the pointer appears
next to EFFECT on the display screen.
Press the [왔] CURSOR button twice.
• This displays the chorus editing screen.
3
You can control the relative strength of an effect and how it is
applied. The parameters you can control depend on the effect.
See the following section titled “CHORUS Parameters” for
more information.
1
Press the [왘] CURSOR button.
• The chorus type setting screen will appear
automatically about fives seconds after you press the
button.
4
Changing the Settings of CHORUS
Parameters
Use the [+] and [–] buttons or the number buttons
to scroll through the chorus types until the one you
want is displayed, or use the number buttons to
input the chorus number you want to select.
• See the list on page A-17 for information about the
types of CHORUS effects that are available.
• Here you could also change the parameters of the
effect you selected, if you want. See “Changing the
Settings of CHORUS Parameters” for more
information.
After selecting the chorus type you want, use the
[왗] and [왘] CURSOR buttons to display the
parameter whose setting you want to change.
• This displays the parameter setting screen.
2
3
Use the [+] and [–] buttons or the number buttons
to input the parameter setting you want.
Press the EFFECT or EXIT button.
• This returns to the tone or rhythm selection screen.
CHORUS Parameters
■ Chorus Level (Range: 000 to 127)
Specifies the size of the chorus sound.
■ Chorus Rate (Range: 000 to 127)
Specifies the undulation speed of the chorus sound. A
higher value produces faster undulation.
■ Chorus Depth (Range: 000 to 127)
Specifies the undulation depth of the chorus sound. A
higher value produces deeper undulation.
NOTE
• Whether or not an effect is applied to the parts that are
sounding also depends on Mixer Mode Reverb Send,
Chorus Send, and DSP on/off settings. See “Mixer
Function” on page E-47 for more information.
E-36
WK3000_e_26-37.p65
735A-E-038A
36
04.3.26, 0:10 PM
Applying Effects to Tones
Using the Equalizer
This keyboard has a built-in four-band equalizer and 10
different settings from which you can choose. You can adjust
the gain (volume) of all four equalizer bands within the range
of –12 to 0 to +12.
To adjust the gain (volume) of a band
1
After selecting the equalizer type you want, use
the [왗] and [왘] CURSOR buttons to select the band
whose gain you want to adjust.
Example: To adjust the HIGH band
To select the equalizer type
1
2
Press the EFFECT button, so the pointer appears
next to EFFECT on the display screen.
Press the [왔] CURSOR button three times.
• This displays the equalizer editing screen.
3
ME q H i g h
2
Use the [+] and [–] buttons or the number buttons
to adjust the band gain.
Example: To adjust the gain to 10
Press the [왘] CURSOR button.
ME q H i g h
• The equalizer type setting screen will appear
automatically about fives seconds after you press the
button.
4
Use the [+] and [–] buttons or the number buttons
to select the equalizer type you want.
• See the list on page A-17 for information about the
equalizer types that are available.
Example: To select Jazz
• Pressing the EXIT or EFFECT button exits the
equalizer setting screen.
NOTE
• Changing to another equalizer type causes the band
gain settings to change to the initial settings for the newly
selected equalizer type automatically.
Jazz
• Pressing the EXIT or EFFECT button exits the
equalizer setting screen.
E-37
735A-E-039A
WK3000_e_26-37.p65
37
04.3.26, 0:10 PM
Auto Accompaniment
RHYTHM
Number buttons
VARIATION/FILL-IN 1/2
TEMPO
This keyboard automatically plays bass and chord parts in
accordance with the chords you finger. The bass and chord
parts are played using sounds and tones that are
automatically selected to select the rhythm you are using.
All of this means that you get full, realistic accompaniments
for the melody notes you play with your right hand, creating
the mood of a one-person ensemble.
About the MODE Button
Use the MODE button to select the accompaniment mode you
want to use. Each press of the MODE button cycles through
the available accompaniment modes as shown in the
illustration below.
Normal (Auto Accompaniment off)
FULL RANGE CHORD
FINGERED
CASIO CHORD
• Only rhythm sounds are produced when all
accompaniment mode lamps are off.
• The currently selected accompaniment mode is shown by
the mode lamps above the MODE button. Information on
using each of these modes starts from page E-40.
E-38
WK3000_e_38-46.p65
735A-E-040B
38
04.3.26, 0:10 PM
Auto Accompaniment
Selecting a Rhythm
Playing a Rhythm
This keyboard provides you with 140 exciting rhythms that
you can select using the following procedure.
You can also transfer accompaniment data from your
computer and store up to 16 of them as user rhythms in
keyboard memory. See “Using the Data Download Service”
on page E-91 for more information.
1
NOTE
NOTE
• Initially, nothing is stored in the user rhythm memory
area.
To play a rhythm
Press VARIATION/FILL-IN button 1 or 2.
• This starts the play of the selected rhythm.
• To stop rhythm play, press the START/STOP button.
• Chords will sound along with the rhythm if any of the
three accompaniment mode lamps above the MODE
button is lit. If you want to play the rhythm pattern without
chords, press the MODE button until all of the lamps
are off.
To select a rhythm
1
2
Find the rhythm you want to use in the rhythm list
and note its rhythm number.
Press the RHYTHM button.
• Not all of the available rhythms are shown on the
rhythm list printed on the keyboard console. For a
complete list, see the “Rhythm List” on page A-14.
Number and name of selected rhythm
8Bea t 1
Adjusting the Tempo
You can adjust the tempo of rhythm play within a range of 30 to
255 beats per minute. The tempo setting is used for Auto
Accompaniment chord play, and song memory operations.
To adjust the tempo
1
Press one of the TEMPO buttons (왖 or 왔).
왖 : Increments displayed value (increases tempo)
왔 : Decrements displayed value (decreases tempo)
Appears when RHYTHM button is pressed
3
Use the number buttons to input the three digit
rhythm number for the rhythm you want to select.
Example: To select “041 ROCK 2”, input 0, 4 and then 1.
Ro c k 2
NOTE
• Pressing both TEMPO buttons (왖 and 왔) at the same
time resets the tempo to the default value of the currently
selected rhythm.
NOTE
• You can also increment the displayed rhythm number
by pressing [+] and decrement it by pressing [–].
E-39
735A-E-041A
WK3000_e_38-46.p65
39
04.3.26, 0:10 PM
Auto Accompaniment
MODE
START/STOP
Using Auto Accompaniment
The following procedure describes how to use the keyboard’s
Auto Accompaniment feature. Before starting, you should
first select the rhythm you want to use and set the tempo of
the rhythm to the value you want.
To use Auto Accompaniment
1
Use the MODE button to select CASIO CHORD,
FINGERED, or FULL RANGE CHORD as the
accompaniment mode.
CASIO CHORD
This method of chord play makes it possible for anyone to
easily play chords, regardless of previous musical knowledge
and experience. The following describes the CASIO CHORD
“accompaniment keyboard” and “melody keyboard”, and
tells you how to play CASIO CHORDs.
CASIO CHORD Accompaniment Keyboard and Melody
Keyboard
Accompaniment
keyboard
Melody keyboard
• The currently selected accompaniment mode is the
one whose lamp is lit. See “About the MODE Button”
on page E-38 for details.
2
3
Press the START/STOP button to start play of the
currently selected rhythm.
Play a chord.
NOTE
• The accompaniment keyboard can be used for playing
chords only. No sound will be produced if you try playing
single melody notes on the accompaniment keyboard.
• The actual procedure you should use to play a chord
depends on the currently selected accompaniment
mode. Refer to the following pages for details on
chord play.
CASIO CHORD .............................. This page
FINGERED ...................................... Page E-41
FULL RANGE CHORD ................ Page E-42
Current measure number
and beat number
Chord name
Ro c k 2
Basic fingering of current chord
(May be different from chord actually
being played on the keyboard.)
4
To stop Auto Accompaniment play, press the START/
STOP button again.
E-40
WK3000_e_38-46.p65
735A-E-042A
40
04.3.26, 0:10 PM
Auto Accompaniment
Chord Types
CASIO CHORD accompaniment lets you play four types of
chords with minimal fingering.
Chord Types
Example
Major chords
Major chord names are marked
above the keys of the
accompaniment keyboard.
Note that the chord produced
when you press an
accompaniment keyboard does
not change octave, regardless
of which key you use to play it.
C Major (C)
FINGERED
FINGERED provides you with a total of 15 different chord
types. The following describes the FINGERED
“accompaniment keyboard” and “melody keyboard”, and
tells you how to play a C-root chord using FINGERED.
FINGERED Accompaniment Keyboard and Melody
Keyboard
CC#DE E FF#GA A B B CC# DE E F
Accompaniment
keyboard
Minor chords (m)
To play a minor chord, keep
the major chord key depressed
and press any other
accompaniment keyboard key
located to the right of the
major chord key.
C minor (Cm)
Seventh chords (7)
To play a seventh chord, keep
the major chord key depressed
and press any other two
accompaniment keyboard keys
located to the right of the
major chord key.
C seventh (C7)
Minor seventh chords (m7)
To play a minor seventh chord,
keep the major chord key
depressed and press any other
three accompaniment
keyboard keys located to the
right of the major chord key.
C minor seventh (Cm7)
CC#DE E FF#GA A B B CC# DE E F
Melody keyboard
NOTE
• The accompaniment keyboard can be used for playing
chords only. No sound will be produced if you try playing
single melody notes on the accompaniment keyboard.
C
Cm
Cdim
Caug *1
Csus4
C7 *2
Cm7 *2
Cmaj7 *2
Cm7 5
C7 5 *1
C7sus4
Cadd9 *2
Cmadd9 *2
CmM7 *2
Cdim7 *1
CC#DE E FF#GA A B B CC# DE E F
CC#DE E FF#GA A B B CC# DE E F
NOTE
• It makes no difference whether you press black or white
keys to the right of a major chord key when playing minor
and seventh chords.
See the “Fingered Chord Chart” on page A-15 for details on
playing chords with other roots.
*1: Inverted fingerings cannot be used. The lowest note is
the root.
*2: The same chord can be played without pressing the 5th G.
E-41
735A-E-043A
WK3000_e_38-46.p65
41
04.3.26, 0:10 PM
Auto Accompaniment
Chords Recognized by This Keyboard
NOTE
• Except for the chords specified in note*1above, inverted
fingerings (i.e. playing E-G-C or G-C-E instead of C-EG) will produce the same chords as the standard
fingering.
• Except for the exception specified in note*2 above, all
of the keys that make up a chord must be pressed.
Failure to press even a single key will not play the desired
FINGERED chord.
The following table identifies patterns that are recognized as
chords by FULL RANGE CHORD.
Pattern Type
Number of Variations
FINGERED
The 15 chord patterns shown
under FINGERED on page E-41.
See the “Fingered Chord Chart” on
page A-15 for details on playing
chords with other roots.
23 standard chord fingerings. The
following are examples of the 23
chords available with C as the bass
note.
FULL RANGE CHORD
This accompaniment method provides a total of 38 different
chord types: the 15 chord types available with FINGERED
plus 23 additional types. The keyboard interprets any input
of three or more keys that matches a FULL RANGE CHORD
pattern to be a chord. Any other input (that is not a FULL
RANGE CHORD pattern) is interpreted as melody play.
Because of this, there is no need for a separate accompaniment
keyboard, so the entire keyboard, from end to end, functions
as a melody keyboard that can be used for both melody and
chords.
C
D
E
F
G
A
B
•
•
•
•
•
•
C
C
C
C
C
C
C
B C m Dm Fm Gm Am Bm
•
•
•
•
•
•
C
C
C
C
C
C
C
Dm75 A7
F7 Fm7 Gm7 Aadd9
•
•
•
•
•
C
C
C
C
C
C
FULL RANGE CHORD Accompaniment Keyboard and
Melody Keyboard
Accompaniment keyboard/Melody keyboard
C6 • Cm6 • C69
Standard
Fingerings
Example: To play the chord C major.
Any of the fingerings shown in the illustration below will
produce C major.
1
E G
C
G
C
E
2
1 ...... Chord C
2 ...... Chord C
E
NOTE
• As with the FINGERED mode (page E-41), you can play
the notes that form a chord in any combination (1).
• When the lowest note of a chord is separated from its
neighboring note by six or more semitones, the lowest
note becomes the bass note (2).
E-42
WK3000_e_38-46.p65
735A-E-044A
42
04.3.26, 0:11 PM
Auto Accompaniment
START/STOP
INTRO/ENDING 1/2
SYNCHRO/FILL-IN NEXT
Using an Intro Pattern
This keyboard lets you insert a short intro into a rhythm
pattern to make startup smoother and more natural.
The following procedure describes how to use the Intro
feature. Before starting, you should first select the rhythm
you want to use, set the tempo, and use the MODE button to
select the chord play method you want to use (Normal,
CASIO CHORD, FINGERED, FULL RANGE CHORD).
1
2
Press the START/STOP button to start rhythm play.
Select the fill-in variation you want.
• To insert Fill-in 1, press the VARIATION/FILL-IN 1
button while Variation 1 of the rhythm is playing.
• To insert Fill-in 2, press the VARIATION/FILL-IN 2
button while Variation 2 of the rhythm is playing.
NOTE
To insert an intro
1
To insert a fill-in
Press INTRO/ENDING button 1 or 2.
• With the above setup, the intro pattern is played and
the auto accompaniment with intro pattern starts as
soon as you play chords on the accompaniment
keyboard.
• Only the SYNCHRO/FILL-IN NEXT button is operational
while an intro is playing.
• Holding down the SYNCHRO/FILL-IN NEXT or
VARIATION/FILL-IN 1/2 buttons causes the fill-in pattern
to repeat.
Using a Rhythm Variation
NOTE
• The standard rhythm pattern starts to play after the intro
pattern is complete.
Using a Fill-in Pattern
Fill-in patterns let you momentarily change the rhythm
pattern to add some interesting variation to your
performances.
The following procedure describes how to use the Fill-in
feature.
In addition to the standard rhythm pattern, you can also
switch to a secondary “variation” rhythm pattern for a bit of
variety .
To insert the variation rhythm pattern
1
2
Press the START/STOP button to start rhythm play.
Press the SYNCHRO/FILL-IN NEXT button.
• If a Variation 1 rhythm is currently playing, this plays
Fill-in 1, followed by Fill-in 2, and then switches to
the Variation 2 rhythm.
• If a Variation 2 rhythm is currently playing, this plays
Fill-in 2, followed by Fill-in 1, and then switches to
the Variation 1 rhythm.
• Holding down the SYNCHRO/FILL-IN NEXT button
causes the fill-in pattern to repeat.
E-43
735A-E-045B
WK3000_e_38-46.p65
43
04.3.26, 0:11 PM
Auto Accompaniment
ONE TOUCH PRESET
MODE
INTRO/ENDING 1/2
SYNCHRO/FILL-IN NEXT
Synchro Starting Accompaniment
with Rhythm Play
You can set up the keyboard to start rhythm play at the same
time you play the accompaniment on the keyboard.
The following procedure describes how to use synchro start.
Before starting, you should first select the rhythm you want
to use, set the tempo, and use the MODE button to select the
chord play method you want to use (Normal, CASIO
CHORD, FINGERED, FULL RANGE CHORD).
To use synchro start
1
Press the SYNCHRO/FILL-IN NEXT button to put
the keyboard into synchro start standby.
AUTO HARMONIZE
Finishing with an Ending Pattern
You can end your performances with an ending pattern that
brings the rhythm pattern you are using to a natural-sounding
conclusion.
The following procedure describes how to insert an ending
pattern. Note that the actual ending pattern played depends
on the rhythm pattern you are using.
To finish with an ending pattern
1
While the rhythm is playing, press INTRO/ENDING
button 1 or 2.
• The timing when the ending pattern starts depends
on when you press the INTRO/ENDING button 1 or
2. If you press the button before the second beat of
the current measure, the ending pattern starts playing
immediately.
NOTE
2
Play a chord and the rhythm pattern starts to play
automatically.
NOTE
• Pressing the INTRO/ENDING button prior to the first half
beat at the beginning of a measure plays the ending
immediately. Pressing the button after the first half beat
of a measure causes the ending to be played from the
beginning of the following measure.
• If the MODE button is set to Normal, only the rhythm
plays (without a chord) when you play on the
accompaniment keyboard.
• If you press the INTRO/ENDING button 1 or 2 before
playing anything on the keyboard, the rhythm starts
automatically with an intro pattern when you play
something on the accompaniment keyboard.
• To cancel synchro start standby, press the SYNCHRO/
FILL-IN NEXT button one more time.
E-44
WK3000_e_38-46.p65
735A-E-046B
44
04.3.26, 0:11 PM
Auto Accompaniment
Using One-touch Preset
Using Auto Harmonize
One-touch preset automatically makes the main settings listed
below in accordance with the rhythm pattern you are using.
When you are using Auto Accompaniment, Auto Harmonize
automatically adds additional notes to your melody in
accordance with the chord that is being played. The result is
a harmony effect that makes your melody line richer and
fuller.
• Keyboard tone
• Layer on/off
• Split on/off
• Auto Harmonize on/off
• Auto Harmonize type
• Accompaniment volume level
• Tempo
• Effect settings
To use Auto Harmonize
1
• The currently selected accompaniment mode is the
one whose lamp is lit. See “About the MODE Button”
on page E-38 for details.
To use one-touch preset
1
2
3
Select the rhythm you want to use.
Normal (Auto Accompaniment off)
Use the MODE button to select the accompaniment
mode you want to use.
FULL RANGE CHORD
FINGERED
Press the ONE TOUCH PRESET button.
• This automatically makes the one-touch preset
settings in accordance with the rhythm you selected.
• The keyboard automatically enters synchro standby
at this time.
4
Use the MODE button to select FINGERED or
CASIO CHORD as the accompaniment mode.
CASIO CHORD
2
Start rhythm and Auto Accompaniment, and play
something on the keyboard.
Press AUTO HARMONIZE button to turn on Auto
Harmonize.
• This causes the AUTO HARMONIZE indicator to
appear on the display.
• Accompaniment is played using the one-touch preset
settings.
3
4
Start Auto Accompaniment play, and play
something on the keyboard.
To turn off Auto Harmonize, press AUTO
HARMONIZE button once.
• This causes the AUTO HARMONIZE indicator to
disappear.
NOTE
• Auto Harmonize turns off temporarily whenever you start
demo tune play. It turns back on as soon as the operation
or function that caused it to turn off is finished.
• Auto Harmonize is enabled only when the Auto
Accompaniment mode is FINGERED or CASIO CHORD.
E-45
735A-E-047B
WK3000_e_38-46.p65
45
04.3.26, 0:11 PM
Auto Accompaniment
ACCOMP VOLUME
Number buttons
[+]/[–]
Auto Harmonize Types
Auto Harmonize lets you select from among the 10 Auto
Harmonize types. Type changing is performed by the setting
item using the TRANSPOSE/FUNCTION button.
See “Changing Other Settings” on page E-79 for more
information.
Adjusting the Accompaniment
Volume
You can adjust the volume of the accompaniment parts as a
value in the range of 000 (minimum) to 127 (maximum).
1
About Auto Harmonize notes and
tones
The notes you play on the keyboard are called “melody
notes”, while the notes added to the melody by Auto
Harmonize is called the “harmonize notes”. Auto Harmonize
normally uses the tone you selected for the melody notes as
the tone for the harmonize notes, but you can use the Mixer
(page E-47) to specify a different tone for the harmonize notes.
The harmonize note tone is assigned to Mixer Channel 5, so
change Channel 5 to the tone you want to use for the
harmonize notes.
In addition to the tone, you can also use the Mixer to change
a number of other parameters, such as volume balance. See
“Using the Parameter Edit Mode” on page E-48 for details
on these procedures.
Press the ACCOMP VOLUME button.
Current accompaniment volume setting
A c om p V o l
2
Use the number buttons or the [+]/[–] buttons to
change the current volume setting value.
Example: 110
A c om p V o l
NOTE
NOTE
• The default harmonize note tone when you first turn on
Auto Harmonize is the same tone as the melody note
tone.
• Changing the melody tone setting automatically changes
the harmonize note tone to the same setting.
• Pressing the ACCOMP VOLUME button or EXIT button
returns to the tone or rhythm setting screen.
• Any channel balance settings you make with the Mixer
are maintained when you change the accompaniment
volume setting.
• Pressing [+] and [–] buttons at the same time
automatically sets an accompaniment volume of 100.
E-46
WK3000_e_38-46.p65
735A-E-048A
46
04.3.26, 0:11 PM
Mixer Function
What you can do with the Mixer
This keyboard lets you play multiple different musical
instrument parts at the same time during autoaccompaniment play, song memory playback, receipt of data
through the MIDI terminal, etc. The Mixer assigns each part
to a separate channel (1 through 16) and lets you control the
channel on/off, volume, and pan pot parameters of each
channel.
In addition to channels 1 through 16, the Mixer also has a
DSP channel that you can use to adjust the DSP level, DSP
pan, and other DSP parameters.
Channel Assignments
See page E-74 and E-75 for information on layered, split, and
layered/split tones.
See page E-61 for information on the song memory.
NOTE
• Normally, keyboard play is assigned to Channel 1. When
Auto Accompaniment is being used, each part of the
accompaniment is assigned to Channels 6 through 10.
• When this keyboard is being used as the sound source
for an externally connected computer or other MIDI
device, all 16 channels are assigned musical instrument
parts. The notes played over the channel selected by
operation under “Turning Channels On and Off” below
are shown on the displayed keyboard and staff.
The following shows the parts that are assigned to each of
the 16 channels.
Channel
Number
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
Channel 9
Channel 10
Channel 11
Channel 12
Channel 13
Channel 14
Channel 15
Channel 16
Part
Main tone (UP1)
Layered tone (UP2)
Split tone (LOW1)
Layered/split tone (LOW2)
Harmonize Tone (HARM)
Auto Accompaniment chord part 1 (CHD1)
Auto Accompaniment chord part 2 (CHD2)
Auto Accompaniment chord part 3 (CHD3)
Auto Accompaniment bass part (BASS)
Auto Accompaniment rhythm part (DRUM)
Song Memory track 1 (TR1)
Song Memory track 2 (TR2)
Song Memory track 3 (TR3)
Song Memory track 4 (TR4)
Song Memory track 5 (TR5)
Song Memory track 6 (TR6)
Turning Channels On and Off
Press the CHANNEL buttons to toggle individual channels
on and off. Indicators on the display show the current on/off
status of each channel.
Channel on
Channel off
• Each press of a CHANNEL button toggles the applicable
channel on and off.
• The on/off status of each channel determines the on/off
status of the corresponding part for keyboard play, Auto
Accompaniment, and Song Memory playback.
• Changing to a different rhythm causes Mixer Settings for
channel 6 through channel 10 to change to the default
settings assigned to the new rhythm. These settings also
change to the defaults for the currently selected rhythm
pattern whenever you switch between the Intro, Normal,
Variation, Fill-in, and Ending patterns.
NOTE
• In this manual, “Channel Number” matches the channel
numbers marked on the keyboard above the CHANNEL
buttons.
• The CHANNEL button name in the above table
corresponds to the text marked on the keyboard below
the CHANNEL buttons.
E-47
735A-E-049B
WK3100_e_47-58.p65
47
04.3.26, 0:11 PM
Mixer Function
MIXER
CHANNEL
CURSOR
Number buttons
[+]/[–]
Using the Parameter Edit Mode
4
Use the number buttons or [+] and [–] to change
the parameter setting.
Example: Change the setting to “060”.
Editing the Parameters for Channels
1 through 16
V o l ume
In the Parameter Edit Mode, you can change the settings of
ten different parameters (including tone, volume, and pan
pot) for the channel you selected on the Mixer screen.
• Pressing the MIXER or EXIT button exits the
parameter edit mode.
To change parameters
Editing DSP Channel Parameters
1
Press the MIXER button.
• This causes a pointer to appear on the display next to
MIXER.
2
Press a CHANNEL button (1 through 16) to select a
channel.
• Use the [왗] and [왘] CURSOR buttons to change
between channels.
3
1
Press the CHANNEL (DSP) button.
• You can also select the DSP channel by pressing the
[왘] CURSOR button while Channel 16 is selected.
• This selects the DSP channel.
• Pressing the [왗] CURSOR button while the DSP
channel is selected returns to Channel 16.
Use [왖] and [왔] CURSOR buttons to select the
parameter whose setting you want to change.
Example: Select volume setting by displaying “Volume”.
• Each press of [왖] or [왔] CURSOR button cycles
through the parameters.
• You can use the [왗] and [왘] CURSOR buttons to
change to another channel at any time during this
procedure.
Indicates channel volume of 127
V o l ume
E-48
WK3100_e_47-58.p65
735A-E-050B
48
04.3.26, 0:11 PM
Mixer Function
How Parameters Work
The following are the parameters whose settings can be
changed in the Parameter Edit Mode.
Tone Parameters
■ Octave Shift (Range: –2 to 0 to +2)
You can use octave shift to shift the range of the tone up or
down. When using the piccolo tone, there may be cases when
very high notes you want to play are not included within the
range of the keyboard. When this happens, you can use octave
shift to shift the keyboard range one octave up.
■ Tone
(Range: 000 to 803, Drawbar organ tones 000 to 199)
This parameter controls the tones assigned to each part.
Anytime the tone is on the display, you can use the TONE
button or DRAWBAR ORGAN button and then select a
different tone, if you want.
G r a n dPno
■ Part On/Off (Settings: on, oFF)
This parameter can be used to turn each part on (sounds)
and off (does not sound). The current on/off status of each
part is indicated on the display as described below.
Ch a n n e l
■ Volume (Range: 000 to 127)
This is the parameter that controls the volume of the selected
channel.
V o l ume
■ Pan Pot (Range: –64 to 00 to +63)
This parameter controls the pan pot, which is the center point
of the left and right stereo channels. Setting “00” specifies
center, a value less than “00” moves the point left, and a value
greater than “00” moves it right.
Oc t Sh i f t
–2 :
–1 :
0:
+1 :
+2 :
Range shifted two octaves down.
Range shifted one octave down.
No shift
Range shifted one octave up.
Range shifted two octaves up.
Tuning Parameters
You can use these parameters to tune each of the parts
individually.
■ Coarse Tune (Range: –24 to 00 to +24)
This parameter controls the coarse tuning of the selected
channel’s pitch in semitone units.
C . Tune
■ Fine Tune (Range: –99 to 00 to +99)
This parameter controls the fine tuning of the selected
channel’s pitch in cent units.
F i neTune
Pan
E-49
735A-E-051A
WK3100_e_47-58.p65
49
04.3.26, 0:11 PM
Mixer Function
■ DSP System Reverb Send (Range: 000 to 127)
Effect Parameters
The Mixer lets you control the effects applied to each
individual part, making it different from the Effect Mode,
whose settings are applied to all parts in general.
This parameter adjusts how much reverb is applied to all
parts.
D . Rv bSnd
■ Reverb Send (Range: 000 to 127)
This parameter controls how much reverb is applied to a part.
A setting of “000” turns reverb off, while a setting of 127
applies maximum reverb.
• “Reverb Send” does not work with some drum sounds.
■ DSP System Chorus Send (Range: 000 to 127)
This parameter adjusts chorus.
D . Ch oSn d
Rv b Send
■ Chorus Send (Range: 000 to 127)
This parameter controls how much chorus send is applied to
a part. A setting “000” turns chorus send off, while a setting
of 127 applies maximum chorus send.
• “Chorus Send” does not work with drum sounds.
Ch o Se n d
■ DSP Line (Settings: on, oFF)
You can use this parameter to turn DSP line off for a particular
channel, or to turn it on.
NOTE
• Changing the tone, volume, pan pot, coarse tune, fine
tune, reverb send, or chorus send setting causes the
corresponding MIDI message to be output from the MIDI
terminal.
• Changing the tone settings changes the tone, octave
shift, reverb send, chorus send, and DSP line* parameter
settings.
* When DSP is off (See the note on page E-82).
• Turning on the Mixer’s DSP Line parameter (on this
page) causes the settings of the DSP Pan, DSP System
Reverb Send, and DSP System Chorus parameters to
be used in place of the Pan Pot, Reverb Send, and
Chorus Send parameters.
DS P L i n e
DSP Part Parameters
■ DSP Level (Range: 0 to 127)
Sets the post-DSP volume.
DS P L e v e l
■ DSP Pan (Range: –64 to 0 to 63)
Sets the post-DSP stereo pan.
DS P P a n
E-50
WK3100_e_47-58.p65
735A-E-052B
50
04.3.26, 0:11 PM
Synthesizer Mode
The Synthesizer Mode of this keyboard provides the tools
for creating your own original tones. Simply select one of the
built-in tones and change its parameters to create your own
original sound. You can even store your sounds in memory
and select it using the same procedure as that used to select a
preset tone.
Synthesizer Mode Functions
The following describes how to use each of the functions
available in the Synthesizer Mode.
(1) Tone Characteristic Waveform
■ Tone Setting
Specifies which of the preset tones should be used as the
original tone.
(2) Volume Characteristic Parameters
These parameters control how the tone changes over time,
from when the keyboard key is pressed until the tone decays.
You can specify changes in volume and sound characteristics.
■ Attack time
Synthesizer Mode Parameters
The preset tones that are built into this keyboard consist of a
number of parameters. To create a user tone, you first recall a
advanced tone (000 to 299) or a preset tone (300 to 499) and
then change its parameters to change it to your own tone.
Note that drum set tones (500 through 515) cannot be used
as the basis of a user tone.
The illustration nearby shows the parameters that make up
the preset tones and what each parameter does. As can be
seen in the illustration, parameters can be divided into four
groups, each of which is described in detail below.
This is the rate or time it takes for the tone to reach its highest
volume level. You can specify a fast rate, where the tone
reaches its highest volume level immediately, a slow rate
where it gradually rises, or something in between.
■ Release time
This is the rate or time it takes for the tone volume to fall to
zero. You can specify a release that ranges from a sudden fall
to zero, to one that gradually falls to zero.
Volume Characteristic
Parameters
Envelope
쎲Attack Time
쎲Release Time
쎲Cutoff Frequency
쎲Resonance
Note ends
Time
Tone Pitch Parameters
Tone Characteristic
Waveform
Tone Setting
쎲Vibrato Type
쎲Vibrato Delay
쎲Vibrato Rate
쎲Vibrato Depth
쎲Octave Shift
A
R
Key pressed
Output
Tone Characteristic
Setting Parameters
쎲Level
쎲Touch Sense
쎲Reverb Send
쎲Chorus Send
쎲DSP Line
쎲DSP Type
쎲DSP Parameter
Key released
A: Attack time
R: Release time
■ Cutoff Frequency
The cutoff frequency is a parameter for adjusting timbre by
cutting any frequency that is higher than a specific frequency.
A larger cutoff frequency produces a brighter (harder) timbre,
while a smaller frequency produces a darker (softer) timbre.
Level
NOTE
• Note that the tone whose parameter you can edit is the
one assigned to the channel (1 through 4) that is currently
selected with the Synthesizer Mode.
Frequency
Cutoff frequency
E-51
735A-E-053A
WK3100_e_47-58.p65
51
04.3.26, 0:11 PM
Synthesizer Mode
■ Resonance
Resonance enhances the harmonic components in the vicinity
of the cutoff frequency, which creates a distinctive sound. A
larger resonance value enhances the sound as shown in the
figure.
Level
Frequency
Cut off frequency
Small Value
Large Value
Resonance
NOTE
• With some tones, a large resonance value can cause
distortion or noise during the attack part of the tone.
(3) Tone Pitch Parameters
■ Vibrato Type, Vibrato Delay, Vibrato Rate, Vibrato
Depth
These parameters adjust the vibrato effect, which causes
periodic changes in the tone.
■ Octave Shift
This parameter controls the octave of all tones.
(4) Tone Characteristic Setting Parameters
■ Level
This parameter controls the overall volume of the tone.
■ Touch Sense
This parameter controls changes in volume and timbre in
accordance with the relative amount of pressure applied to
the keyboard keys. You can specify more volume for stronger
pressure and less volume or a lighter pressure, or you can specify
the same volume regardless of how much pressure is applied to
the keys.
■ Reverb Send, Chorus Send, DSP Line , DSP Type, DSP
Parameter
These parameters control the effects applied to tones.
E-52
WK3100_e_47-58.p65
735A-E-054A
52
04.3.26, 0:11 PM
Synthesizer Mode
Saving User Tones
The group of tone numbers from 600 through 699 (User 001 through User 100) is called the “user area” because they are reserved for
storage of user tones. After you recall a preset tone and change its parameters to create your own user tone, you can store it in the user
area for later recall. You can recall your tones using the same procedure that you use when selecting a preset tone.
Number Tone Type
Standard Tone
000-299 Advanced Tones
300-499 Preset Tones
500-515 Drum Sets
Source Tone Select
Parameter Edit
Save As Original Tone
600-699 User Tones*1
600-699 User Area
700-719 User Tones with Waves*2
800-803 User Drum Sets with Waves*3
Drawbar Organ Tones
000-049 Preset Tones
100-199 User Tones*4
*1: You can select any Advance Tone, preset tone, or user tone. User tone areas 600 through 699 initially contain the same data as
DSP types 000 through 099.
*2: Area where data transferred from computer is stored (see “Using the Data Downloard Service” on page E-91). After transfer,
you can use the keyboard to edit parameters, but you can only overwrite existing parameters. You cannot save the data to
another number. Initially, nothing is stored in the user tone with wave memory area.
*3: Area where data transferred from computer is stored (see “Using the Data Downloard Service” on page E-91). Transfer only
is allowed, and no parameter editing is allowed. Initially, nothing is stored in the user drum set with wave memory area.
*4: User tones created by modifying parameters of one of the preset tones (000 to 049). User drawbar organ tone areas initially
contain two sets of the same data as drawbar organ tones types 000 through 049.
NOTE
• You can create an original tone using a user tone that includes a waveform (tone number 700 to 719). In this case, the
storage area is the same as the source tone area. For example, an original tone created using tone number 700 as a source
tone is stored in user area number 700.
E-53
735A-E-055A
WK3100_e_47-58.p65
53
04.3.26, 0:11 PM
Synthesizer Mode
SYNTH
CURSOR
●WK-3100/WK-3000
MODULATION button lamp
[+]/[–]
Creating a User Tone
Parameters and Their Settings
Use the following procedure to select a preset tone and change
its parameters to create a user tone.
The following describes the function of each parameter and
provides its setting range.
1
■ Attack Time (Range: –64 to 00 to +63)
2
First, select the preset tone you want to use as a
basis for your user tone.
Press the SYNTH button.
• This enters the Synthesizer Mode, which is indicated
by the pointer next to SYNTH on the display screen.
A t k T i me
■ Release Time (Range: –64 to 00 to +63)
Parameter setting value
Currently selected parameter
A t k T i me
3
Time it takes before the tone sounds after a key is pressed
Use [왗] and [왘] CURSOR buttons to display the
parameter whose setting you want to change.
Time the tone continues to sound after a key is released
R e l . T i me
■ Cutoff Frequency
(Range: –64 to 00 to +63)
High-band cutoff for the harmonic components of the tone
V i bDe l a y
• Each press of [왗] or [왘] CURSOR button changes to
the next parameter. See “Parameters and Their
Settings” on this page for information on setting range
for each parameter.
4
Use [+] and [–] to change the setting of the currently
selected parameter.
C- o f f Fr q
■ Resonance (Range: –64 to 00 to +63)
Resonance of the tone
Re s o n a n .
• You can also use the number buttons to input a value
to change a parameter setting. See “Parameters and
Their Settings” on this page for information on setting
range for each parameter.
5
After you are finished editing the sound, press the
SYNTH button to exit the Synthesizer Mode.
NOTE
• See “Storing a User Tone In Memory” on page E-57 for
details on saving user tone data to memory so it is not
deleted.
E-54
WK3100_e_47-58.p65
735A-E-056C
54
04.3.26, 0:11 PM
Synthesizer Mode
■ Modulation Assign (Range: *)
The Modulation Assign parameter specifies which
parameters should be affected when you use the keyboard’s
modulation function. Select “oFF” for any parameters that
you do not want affected by the modulation function.
Mo d u l a t .
■ Modulation Depth (Range: 0 to 127) (WK-3100/WK3000 only)
On the WK-3100/WK-3000, this parameter controls the
modulation value when the MODULATION button is pressed.
How the MODULATION button functions depends on the
modulation assign parameter setting as described below.
If this setting is
selected for
modulation assign:
Modulation is applied like this:
vib
Modulation is applied to the depth specified
by the value assigned to the Modulation
Depth parameter as long as the
MODULATION button is depressed.
Releasing the MODULATION button causes
the modulation value to return to the initial
default value for the tone being used.
dp0 through dp7
Each press of the MODULATION button
toggles modulation between the value
assigned to the Modulation Depth Parameter
and the initial default value for the tone being
used.
*
Value
Meaning
oFF
Off
vib
Control Change 01h (Modulation)
dp0
Control Change 16
(Normally assigned to DSP Parameter 0.)
dp1
Control Change 17
(Normally assigned to DSP Parameter 1.)
dp2
Control Change 18
(Normally assigned to DSP Parameter 2.)
dp3
Control Change 19
(Normally assigned to DSP Parameter 3.)
dp4
Control Change 80
(Normally assigned to DSP Parameter 4.)
dp5
Control Change 81
(Normally assigned to DSP Parameter 5.)
dp6
Control Change 82
(Normally assigned to DSP Parameter 6.)
dp7
Control Change 83
(Normally assigned to DSP Parameter 7.)
NOTE
Mo d D e p t h
MODULATION Button Lamp
The MODULATION button lamp lights when the current
modulation depth is at its greatest possible setting. This can
occur either when the MODULATION button is depressed
or released, depending on the current Modulation Depth
parameter setting and the initial default modulation depth
value of the tone you are currently using.
• If the Modulation Assign setting of a tone is any setting
from dp0 through dp7, that setting is ignored when the
tone is used as a layered or split tone. DSP parameter
effects are applied to the main tone only.
E-55
735A-E-057C
WK3100_e_47-58.p65
55
04.3.26, 0:11 PM
Synthesizer Mode
■ Vibrato Waveform (Range: See below.)
■ Touch Sensitivity (Range: –64 to 00 to +63)
Specifies the vibrato waveform.
This parameter controls changes in the volume of the tone in
accordance with the pressure applied to the keyboard keys. A
greater positive value increases the volume of the output as
pressure increases, while a negative value decreases volume
with increased keyboard pressure. A setting of zero specifies
no change in output volume in accordance with keyboard
pressure.
V i b . Type
Value
Meaning
Sin
Sine Wave
tri
Triangle Wave
SAU
Sawtooth Wave
Sqr
Square Wave
Waveform
T c hSen s e
■ Reverb Send (Range: 000 to 127)
This parameter adjusts reverb.
Rv b Send
■ Vibrato Delay (Range: –64 to 00 to +63)
Specifies the amount of time before vibrato starts.
■ Chorus Send (Range: 000 to 127)
This parameter adjusts chorus.
V i bDe l a y
■ Vibrato Rate (Range: –64 to 00 to +63)
Rate (speed) of the vibrato effect
Ch o Se n d
■ DSP Line (Settings: on, oFF)
This parameter controls whether or not the DSP effect is used.
V i b . Ra t e
DS P L i n e
■ Vibrato Depth (Range: –64 to 00 to +63)
Depth of the vibrato effect
V i bDe p t h
■ Octave Shift (Range: –2 to 0 to +2)
Up/down octave shift
Oc t Sh i f t
■ Level (Range: 000 to 127)
This parameter controls the overall volume of the tone. The
greater the value, the greater the volume. Setting a level of
zero means that the tone does not sound at all.
Leve l
E-56
WK3100_e_47-58.p65
735A-E-058A
56
04.3.26, 0:11 PM
Synthesizer Mode
SYNTH
CURSOR
[+]/[–]
Storing a User Tone In Memory
DSP Settings
Use the DSP editing screen to select the DSP type and to edit
parameters.
1
2
Select a tone, press the SYNTH button, and then
configure parameter settings.
After everything is the way you want, press the [왔]
CURSOR button once.
• This advances to the DSP parameter editing screen.
• Pressing the [왖] CURSOR button returns to the
Synthesizer Mode parameter screen.
The following procedure shows how to store a user tone in
memory. Once a tone is stored, you can call it up just as you
do with a preset tone.
To name a user tone and store it in
memory
1
This setting specifies DSP parameters. See “DSP Parameters”
on page E-33, “Effect List” on page A-17, and “DSP Algorithm
List” on page A-19 for more information.
2
NOTE
3
• If you store an original tone with the DSP line turned on
(page E-56), simply recalling the tone automatically
changes the DSP line, DSP type, and DSP parameter
settings. This simplifies the recall of original tones that
include a DSP effect.
Select a preset tone to use as the basis for the user
tone, press the SYNTH button to enter the
Synthesizer Mode, and make the parameter settings
you want.
After making parameter settings to create the user
tone, press [왔] CURSOR button twice.
Use [+] and [–] to change the user area tone number
on the display until the one where you want to
store the tone is shown.
• You can select any tone number from 600 to 699.
User Tone Creation Hints
The following hints provide helpful advice on making user
tone creation a bit quicker and easier.
Use a preset tone that is similar to the one you are trying to
create.
Whenever you already have a rough idea of the tone you are
trying to create, it is always a good idea to start with a preset
tone that is similar.
■ Experiment with various different settings.
4
After the tone name is the way you want, press the
[왘] CURSOR button to store the tone.
• Use the [+] and [–] buttons to scroll through letters at
the current cursor location.
• Use the [왗] and [왘] CURSOR buttons to move the
cursor left and right.
• See the page E-103 for information about inputting
text.
There are no real rules about what a tone should sound like.
Let your imagination run free and experiment with different
combinations. You may be surprised at what you can achieve.
E-57
735A-E-059B
WK3100_e_47-58.p65
57
04.3.26, 0:11 PM
Synthesizer Mode
CURSOR
5
Press [왔] CURSOR button to save the user tone.
• This will display a confirmation message asking
whether you really want to save the data. Press the
YES button to save the data.
• The message “Complete” appears momentarily on the
display, followed by the tone or rhythm selection
screen.
• To abort the save operation at any time, press the
SYNTH button or the EXIT button to exit the
Synthesizer Mode. Pressing the SYNTH button again
(before selecting another tone) returns to the
Synthesizer Mode with all of your parameter settings
still in place.
E-58
WK3100_e_47-58.p65
735A-E-060B
58
04.3.26, 0:11 PM
Registration Memory
Registration Memory Features
Registration memory lets you store up to 32 keyboard setups
(4 sets x 8 banks) for instant recall whenever you need them.
The following is a list of settings that are saved in registration
memory.
Setup Names
You can assign setups into one of 32 areas, which you can
select using BANK buttons 1 through 4 and the four
REGISTRATION buttons. Area names range from 1-1 through
8-4 as shown below.
Registration Memory Settings
• Tone
• Rhythm
• Tempo
• Layer on/off
• Split on/off
• Split point
• Auto Harmonize on/off
• Mixer settings (Channels 1 to 10)
• Effect settings
• Touch Response settings
• Assignable jack setting
• Transpose
• Tuning
• Accompaniment volume setting
• Pitch bend range
• Auto Harmonize type
• MODE button setting
• Synchro standby state
• Mixer Hold
• DSP Hold
• Synthesizer Mode parameters (Modulation Assign,
Modulation Depth, Vibrato Waveform, Vibrato Delay,
Vibrato Rate, and Vibrato Depth only)
NOTE
• Each bank of registration memory initially contains data
when you first use the keyboard. Simple replace the
existing data with your own data.
• Registration memory functions are disabled while you
are using the SMF Player, Song Memory or demo tune
function.
• Registration memory functions are also disabled while
you are using the floppy disk drive (WK-3500 only) or
card slot (page E-94).
1
BANK 1
2
1
2
3
4
1-1
1-2
1-3
1-4
BANK 2
2-1
2-2
2-3
2-4
BANK 3
3-1
3-2
3-3
3-4
BANK 4
4-1
4-2
4-3
4-4
BANK 5
5-1
5-2
5-3
5-4
BANK 6
6-1
6-2
6-3
6-4
BANK 7
7-1
7-2
7-3
7-4
BANK 8
8-1
8-2
8-3
8-4
1 Use the BANK button to select the bank. Each press of
BANK cycles through the bank numbers from 1 to 8.
2 Pressing one of the REGISTRATION buttons (1 to 4) selects
the corresponding area in the currently selected bank.
NOTE
• Whenever you save a setup and assign it a setup name,
any setup data previously assigned to that name is
replaced with the new data.
• You can use the keyboard’s MIDI capabilities to save
your setup data to a computer or other external storage
device. See “Using the Data Download Service” on page
E-91 for details.
• You can save setup data to external media, if you want.
See “Saving Data” on page E-92 for more information.
E-59
735A-E-061B
WK3000_e_59-60.p65
59
04.3.26, 0:11 PM
Registration Memory
Number buttons
BANK
REGISTRATION
STORE
To Save a Setup in Registration
Memory
To Recall a Setup from
Registration Memory
1
1
Select a tone and rhythm, and otherwise set up the
keyboard the way you want it.
• See “Registration Memory Settings” on page E-59 for
details on what data is stored in the registration
memory.
2
Use the BANK button or the number buttons to
select the bank.
• If you do not perform any operation for about five
seconds after pressing the BANK button, the keyboard
automatically clears the registration memory recall
screen.
Use the BANK button or the number buttons to
select the bank you want.
• If you do not perform any operation for about five
seconds after pressing the BANK button, the display
returns to the contents in step 1, above.
• Bank 1 selected.
Ban k
2
Press the REGISTRATION button (1 to 4) or number
buttons for the area whose setup you want to recall.
Ban k
3
While holding down the STORE button, press a
REGISTRATION button (1 to 4).
• The following display appears when you press the 2
button.
Store
4
Re c a l l
• The setup name along with the message “Recall”
appears on the display.
NOTE
• If you press a REGISTRATION button without using the
BANK button to select a bank first, the last bank number
selected is used.
Release the STORE and REGISTRATION buttons.
NOTE
• The setup is saved as soon as you press a
REGISTRATION button in step 3, above.
E-60
WK3000_e_59-60.p65
735A-E-062A
60
04.3.26, 0:11 PM
Song Memory Function
This keyboard lets you record up to five separate songs in
song memory for later playback. There are two methods you
can use to record a song: real-time recording where you record
the notes as you play them on the keyboard, and step
recording where you input chords and notes one-by-one.
Selecting a Track
Use the SONG MEMORY TRACK buttons marked CHORD/
TR1 through TR6 to select the track you want.
Song Memory Track Buttons
NOTE
Track 4
• Layer and split cannot be used while standing by for
recording or while recording is being performed in the
Song Memory Mode. Also, layer and split are
automatically turned off whenever the keyboard goes
into record standby or starts recording.
Track 2
Track 1
Track 6
Track 3
Track 5
Tracks
Keyboard song memory records and plays back much like a
standard tape recorder. There are a total of six tracks, each of
which can be recorded separately. Besides notes, each track
can have its own tone number. Then when you play back the
tracks together, it sounds like an entire six-piece band. During
playback, you can adjust the tempo to change the speed of
playback.
Start
Track 1
End
Basic Song Memory operations
The status of the Song Memory changes each time you press
the SONG MEMORY button.
Playback
P l ay
Auto accompaniment (Rhythm,
Bass, Chord 1/2/3), Keyboard play
Track 2
Keyboard play
Track 3
Keyboard play
Track 4
Keyboard play
Track 5
Keyboard play
Track 6
Keyboard play
Melody data recorded in track.
NOTE
• With this keyboard, Track 1 is the basic track, which
can be used to record keyboard play, along with Auto
Accompaniment. Tracks 2 through 6 can be used for
keyboard play, so they are called melody tracks. Tracks
2 through 6 are used to add other parts to what is
recorded in Track 1.
• Note that each track is independent of the others. This
means that even if you make a mistake while recording,
you only need to re-record the track where the mistake
was made.
• You can use different Mixer settings for each track (page
E-47).
Real-time Recording
Re c o r d
Step Recording
S t e p Re c
Flash
Normal
E-61
735A-E-063A
WK3100_e_61-73.p65
Flash
61
04.3.26, 0:11 PM
Song Memory Function
SONG MEMORY
Number buttons
START/STOP
Using Real-time Recording
4
• When recording starts, the REC indicator flashes on
the display. After a few moments the indicator stops
flashing, and remains on the display.
• Real-time recording without a rhythm starts. If you
want to record with a rhythm, press the INTRO/
ENDING 1/2 or VARIATION/FILL-IN 1/2.
With real-time recording, the notes you play on the keyboard
are recorded as you play them.
To record with real-time recording
1
Press the SONG MEMORY button twice to enter
real-time record standby.
5
6
2
Use the number buttons to select a song number
(0 to 4).
Song number
Play something on the keyboard.
• You can also record Auto Accompaniment chords by
selecting the applicable mode with the MODE button.
• Optional pedal, pitch bend and modulation
operations are also recorded. See “Track 1 Contents
After Real-time Recording”.
• Perform step 2, below, within five seconds after
entering record standby.
• The level meters for tracks 11 through 16 are shown
on the display while the keyboard is in record standby,
so you can easily check which tracks are already
recorded. See “Level Meter Contents During Record/
Edit Standby” on page E-69 for details.
Press the START/STOP button to start recording.
Press the START/STOP button to end recording
when you are finish playing.
• If you make a mistake while recording, you can stop
the record operation and begin over again from step
1, or you can use the editing function (page E-70) to
make corrections.
NOTE
• Using real-time recording to record to a track that already
contains recorded data replaces the previous recording
with the new one.
Re c o r d
• The above song number screen remains on the display
for about five seconds.
3
Make the following settings.
• Tone number
• Rhythm number
• Tempo
• MODE button
E-62
WK3100_e_61-73.p65
735A-E-064B
62
04.3.26, 0:11 PM
Song Memory Function
Track 1 Contents After Real-time
Recording
In addition to keyboard notes and accompaniment chords,
the following data is also recorded to Track 1 during realtime recording. This data is applied whenever Track 1 is
played back.
• Tone number
• Rhythm number
• INTRO/ENDING 1 button, INTRO/ENDING 2 button,
VARIATION/FILL-IN 1 button, VARIATION/FILL-IN 2
button, SYNCRHO/FILL-IN NEXT button operations
• Pedal operations (option)
The following data is recorded in the header whenever you
start a recording of a track.
• Mixer settings of other tracks
• Effect type
• Accompaniment volume
• Reverb Level
• Chorus Level
• DSP Hold On/Off
• Mixer Hold On/Off
• Pitch bend wheel operation
• Modulation wheel operation (WK-3500)
• Modulation button operation (WK-3100/WK-3000)
• Pitch bend range
Mixer Mode Settings
Channel 1 Mixer parameters (page E-47) are automatically
recorded to Track 1. You can use the Mixer to change each of
the parameters.
Memory Capacity
Memory Data Storage
• Whenever you make a new recording, anything previously
stored in memory is replaced.
• Turning off the keyboard while a record operation is in
progress causes the contents of the track your are currently
recording to be lost.
• You can save memory data to external media, if you want.
See “Saving Data” on page E-92 for more information.
• Remember that you can dump memory contents to another
MIDI device using the procedure described under “Using
the Data Download Service” on page E-91.
Track 1 Real-time Recording
Variations
The following describes a number of different variations you
can use when recording to Track 1 using real-time recording.
All of these variations are based upon the procedure described
under “To record with real-time recording” on page E-62.
To start recording with synchro start
In place of step 4, press the SYNCHRO/FILL-IN NEXT
button. Auto-accompaniment and recording will both start
when you play a chord on the accompaniment keyboard.
To record using an intro, ending, or fill-in
During recording, the INTRO/ENDING 1/2, SYNCHRO/
FILL-IN NEXT, and VARIATION/FILL-IN 1/2 buttons
(pages E-43 to 44) can all be used as they normally are.
To synchro start Auto Accompaniment with an intro
pattern
In place of step 4, press the SYNCHRO/FILL-IN NEXT button
and then INTRO/ENDING 1 or INTRO/ENDING 2 button.
Auto-accompaniment will start with the intro pattern when
you play a chord on the accompaniment keyboard.
The keyboard has memory for approximately 10,000 notes.
• The measure number and note number flash on the display
whenever remaining memory is less than 100 notes.
• Recording automatically stops (and auto-accompaniment
and rhythm stops playing if they are being used) whenever
memory becomes full.
• Initially, nothing is stored in song memory.
To start Auto Accompaniment part way into a recording
In place of step 4, press the SYNCHRO/FILL-IN NEXT button
and then play something on the melody keyboard to start
recording without Auto Accompaniment. When you reach
the point where you want accompaniment to start, play a
chord on the accompaniment keyboard to start Auto
Accompaniment.
E-63
735A-E-065C
WK3100_e_61-73.p65
63
04.3.26, 0:11 PM
Song Memory Function
SONG MEMORY
Number buttons
SYNCHRO/FILL-IN NEXT
START/STOP
Playing Back from Song Memory
Once you record tracks to song memory, you can play them
back to see what they sound like.
To play back from song memory
1
Use the SONG MEMORY button to enter playback
standby, and then use the number buttons to select
a song number (0 to 4).
Song number
Playback standby
P l ay
• The above song number screen remains on the display
for about five seconds. If it disappears before you have
a chance to select a song number, use the [왔] CURSOR
button to re-display it.
2
Press the START/STOP button to playback the song
you selected.
SONG MEMORY TRACK
Recording Melody and Chords
with Step Recording
With step recording, you can record Auto-Accompaniment
chords and notes, and even specify note lengths one by one.
Even those who find it difficult to play along on the keyboard
with an Auto-Accompaniment can create AutoAccompaniments based on their own original chord
progressions. The following shows the type of data that can
be recorded in Tracks 1 through 6.
Track 1: Chords and Auto-Accompaniment
Tracks 2 through 6: Keyboard play
With step recording, first record the chords and AutoAccompaniment in Track 1. Next, record the melody in Tracks
2 through 6.
NOTE
• Use the procedure under “To record to Tracks 2 through
6 using step recording” on page E-68 for details on how
to record to Tracks 2 through 6.
• You can use the TEMPO buttons to adjust the playback
tempo.
• Press the START/STOP button again to stop playback.
NOTE
• You can play along on the keyboard using layer (page
E-74) and split (page E-75) during playback.
• Pressing the START/STOP button to start playback from
song memory always starts from the beginning of the
song.
• The entire keyboard functions as a melody keyboard,
regardless of the MODE button setting.
To turn off a specific track
Press the SONG MEMORY TRACK button of the track you
want to turn off, or use the Mixer (Page E-47) to turn off the
channel of the track.
E-64
WK3100_e_61-73.p65
735A-E-066A
64
04.3.26, 0:11 PM
Song Memory Function
To record chords with step recording
1
Press the SONG MEMORY button three times to
enter step recording standby, and then use the
number buttons to select the song number (0 to 4).
7
After you are finished recording, press the START/
STOP button.
• This enters playback standby for the song you have
just recorded.
• To play back the song at this time, press the START/
STOP button.
Flash
NOTE
S t e p Re c
2
Make the following settings.
• Rhythm number
• MODE button
3
Press the CHORD/TR1 button, which is one of the
SONG MEMORY TRACK buttons, to select Track1.
• When recording starts, the REC indicator flashes on
the display. After a few moments the indicator stops
flashing, and remains on the display.
4
5
Press the SYNCHRO/FILL-IN NEXT button.
Play a chord.
• Use the chord play method that is specified by the
current MODE button setting (Fingered, CASIO
Chord, etc.).
• When the MODE button is set to Normal, specify the
chord using the root input keyboard and chord type
input keyboard. See “Specifying Chords in the
Normal Mode” on page E-66 for details.
Ch o r d
Cord name
Measure, beat, and clock at
current location*
* 96 clocks = 1 beat
6
Input the length of the chord (how long it should
be played until the next chord is played).
• Use the procedure under “Correcting Mistakes While
Step Recording” on page E-69 to correct input mistakes
you make during step recording.
• You can add on to a track that already contains recorded
data by selecting that track in step 3 of the above
procedure. Doing so automatically locates the step
recording start point at the first beat immediately
following the previously recorded data.
• Inputting “0” as the chord length in steps 5 and 6 of the
above procedure specifies a rest, but the rest is not
reflected in the accompaniment contents when the
accompaniment is played.
Track 1 Contents After Step
Recording
In addition to chords, the following data is also recorded to
Track 1 during step recording. This data is applied whenever
Track 1 is played back.
• Rhythm number
• INTRO/ENDING 1 button, INTRO/ENDING 2 button,
VARIATION/FILL-IN 1 button, VARIATION/FILL-IN 2
button, SYNCHRO/FILL-IN NEXT button operations
NOTE
• You can also use number buttons 1 through 7, and button
9 to specify the button release timing for the VARIATION/
FILL-IN 1, VARIATION/FILL-IN 2, and SYNCHRO/FILLIN buttons. For more information, see “Specifying the
Length of a Note” on page E-66. Specifying release
timing specifies that the applicable button remains
depressed for a particular amount of time. If you do not
specify the release timing, it is assumed that the button
is pressed and then immediately released.
• Use the number buttons to specify the length of the
chord. See “Specifying the Length of a Note” on page
E-66 for details.
• The specified chord and its length are stored in
memory and the keyboard stands by for input of the
next chord.
• Repeat steps 5 and 6 to input more chords.
E-65
735A-E-067B
WK3100_e_61-73.p65
65
04.3.26, 0:11 PM
Song Memory Function
Specifying Chords in the Normal
Mode
When the MODE button is set to Normal during step
recording, you can specify chords using a method that is
different from CASIO Chord and Fingered fingerings. This
chord specification method can be used to input 18 different
chord types using only two keyboard keys, so chords can be
specified even if you don’t know how to actually play them.
Chord type input
keyboard
Root input keyboard
1
2
3
4
5
6
7
8
9
Major
Minor
Augmented
Diminished
Suspended four
Seventh
Minor seventh
Major seventh
Minor major seventh
0
A
B
C
D
E
F
G
H
Seventh flat five
Minor seventh flat five
Seventh suspended four
Diminished seventh
Minor add ninth
Add ninth
Minor sixth
Sixth
Six ninth
To specify a chord, hold down the key on the root input
keyboard that specifies the root, and press the key in the chord
type input keyboard to specify the chord type. When
inputting a chord with a specified bass note, pressing two
keys of the root input keyboard causes the lower note to be
specified as a bass note.
Example 1: To input Gm7, hold down G on the root input
keyboard and press the m7 key on the chord type
input keyboard.
(G)
Hold down key to specify chord
root.
(m7)
Press key to specify chord
type
Example 2: To input Gm/C, hold down C and G on the root
input keyboard and press the m key on the chord
type input keyboard.
(C)
(G)
Hold down key to specify on bass
and chord root.
Specifying the Length of a Note
During step recording, the number buttons are used to specify
the length of each note.
Note lengths
Use number buttons [1] through [6] to specify whole notes
( ), half notes ( ), quarter notes ( ), eighth notes ( ), 16th
notes ( ), and 32nd notes ( ).
Example: To specify a quarter note ( ), press [3].
Dots ( ) and triplicates (
)
While holding down the [7] (dot) or [9] (triplicate), use buttons
[1] through [6] to input the lengths of the notes.
Example: To input a dotted eighth notes ( ), hold down [7]
and press [4].
Ties
Input the first and then the second note.
Example: To input
, press [4] and then [8]. Next, press
[5]. This note will be tied to the next note you input
(16th note in this example).
Rest
Hold down [0] and then use number buttons [1] through [9]
to specify the length of the rest.
Example: To input an eighth note rest, hold down [0] and press
[4].
• Pressing the [왘] CURSOR button inputs rests up to the
beginning of the next measure.
Track 1 Step Recording Variations
The following describes a number of different variations you
can use when recording to Track 1 using step recording. All
of these variations are based upon the procedure described
under “To record chords with step recording” on page E-65.
To start accompaniment with an intro pattern
In step 4, press INTRO/ENDING 1 or INTRO/ENDING 2
button after the SYNCHRO/FILL-IN NEXT button.
To switch to a rhythm variation
In step 5, press VARIATION/FILL-IN 1 or VARIATION/
FILL-IN 2 button immediately before inputting the chord.
To insert a fill in
In step 5, press VARIATION/FILL-IN 1 or VARIATION/
FILL-IN 2 button at the measure or beat immediately before
the chord or beat where you want to insert the fill in.
(m)
Press key to specify
chord type.
To insert an ending
In step 5, press INTRO/ENDING 1 or INTRO/ENDING 2
button at the measure or beat immediately before the chord
where you want to insert the ending.
E-66
WK3100_e_61-73.p65
735A-E-068B
66
04.3.26, 0:11 PM
Song Memory Function
SONG MEMORY
Number buttons
START/STOP
IMPORTANT!
• The length of the ending depends on the rhythm you
are using. Check the length of the pattern you are using
and set the length of the chord accordingly in step 6.
Making the chord too short in step 6 can result in the
ending pattern being cut off.
SONG MEMORY TRACK
To record to Tracks 2 through 6 using
real-time recording
You can record to Tracks 2 through 6 while playing back what
you originally recorded on Track 1 and any other tracks that
are already recorded.
1
To step record chords without rhythm
Skip step 4. The specified chord of the length specified by
the number buttons is recorded. A rest can be specified here,
so an original chord pattern can be created.
To add chord accompaniment part way through rhythm
play
In place of step 4 at the start of the recording, press
VARIATION/FILL-IN 1 or VARIATION/FILL-IN 2 button
and input rests. Then in step 5, input the chords. Only rhythm
is played where you input the rests, and then chord play starts
after the rests.
Recording Multiple Tracks
Track 1 of the keyboard’s song memory records Auto
Accompaniment and keyboard play. In addition, there are
five other melody tracks that you can use to record melody
parts only. You can record different tones to the melody tracks
and build a full ensemble of instruments for your recordings.
The procedure you use for recording to Tracks 2 through 6 is
identical to the one you use when recording to Track 1.
Press the SONG MEMORY button twice to enter
record standby, and then use the number buttons
to select a song number (0 to 4).
• The song number you select should be the one where
you previously input Track 1.
2
Use the SONG MEMORY TRACK buttons to select
the track you want to record to (2 through 6).
• While the keyboard is in record standby, the display
shows the level meters for channels 11 through 16, so
you can check which tracks have already been
recorded. See “Level Meter Contents During Record/
Edit Standby” on page E-69 for details.
3
Make the following settings.
• Tone number
• Tempo
4
Press the START/STOP button to start recording.
• At this time, the contents of any tracks that are already
recorded start to play back.
• Optional pedal, pitch bend and modulation
operations are also recorded.
5
6
Use the keyboard to play what you want to record
the track you selected.
Press the START/STOP button to end recording
when you are finished.
E-67
735A-E-069B
WK3100_e_61-73.p65
67
04.3.26, 0:11 PM
Song Memory Function
SONG MEMORY
CURSOR
Number buttons
START/STOP
Track Contents After Real-time
Recording
SONG MEMORY TRACK
2
Use the SONG MEMORY TRACK buttons to select
the track you want to record to (2 through 6).
Example: Select Track 2.
In addition to keyboard notes, the following data is also
recorded to the selected track during real-time recording. This
data is applied whenever the track is played back.
Flash
• Tone number
• Pedal operations (option)
The following data is recorded in the header whenever you
start a recording of a track.
• Mixer settings of other tracks
• Effect type
• Accompaniment volume
• Reverb Level
• Chorus Level
• DSP Hold On/Off
• Mixer Hold On/Off
• Pitch bend wheel operation
• Modulation wheel operation (WK-3500)
• Modulation button operation (WK-3100/WK-3000)
• Pitch bend range
To record to Tracks 2 through 6 using
step recording
This procedure describes how to input notes one-by-one,
specifying each note’s pitch and length.
1
Press the SONG MEMORY button three times to
enter real-time record standby, and then use the
number buttons to select a song number (0 to 4).
• The song number you select should be the one where
you previously input Track 1.
3
Specify a tone number.
• Pressing a TONE button or the DRAWBAR ORGAN
button displays the tone number and name on the
display. You can then use the number buttons, or the
[+] (increase) and [–] (decrease) buttons to change the
tone.
• After changing the tone number, press any keyboard
key to clear the tone number and name screen, and
return to the note input screen.
4
Use the keyboard keys to input notes, or the [0]
button to input rests.
• At this time, the display shows the keyboard pressure
(velocity). Use the [+] (increase) and [–] (decrease)
buttons to change the velocity.
• You can also input a chord.
5
6
7
Use the number buttons to input the length of the
note or rest (page E-66).
Repeat steps 4 and 5 to input more notes.
Press the START/STOP button to end recording
when you are finished.
S t e p Re c
E-68
WK3100_e_61-73.p65
735A-E-070C
68
04.3.26, 0:11 PM
Song Memory Function
NOTE
• Use the procedure under “Correcting Mistakes While
Step Recording” on this page to correct input mistakes
you make during step recording.
• You can add on to a track that already contains recorded
data by selecting that track in step 2 of the above
procedure. Doing so automatically locates the step
recording start point at the first beat immediately
following the previously recorded data.
• Whenever you are recording to Tracks 2 through 6, the
entire keyboard functions as a melody keyboard,
regardless of the current MODE button setting.
To correct mistakes while step
recording
1
Without exiting step recording, use the [왗]
CURSOR button to move the input point to the left.
• The REC indicator disappears from the display, and
the STEP indicator flashes.
No t e C# 4
Track Contents After Step Recording
In addition to notes and rests, the following data is also
recorded to the track during step recording. This data is
applied whenever the track is played back.
Measure 126/Beat 3/Clock 48
(Normal input point)
Data flow
•••••••
• Tone number
Measure 126/Beat 3/Clock 0
(Previous data)
Data flow
• • • • • • •
•••••••
C4
Level Meter Contents During Record/
Edit Standby
Channels 11 through 16 correspond to Tracks 1 through 6.
Whenever the keyboard is in record or edit (page E-70)
standby, the level meter display shows which tracks already
contain recorded data and which are still empty. Tracks with
four lit segments already contained recorded data, while
tracks with one lit segment are not yet recorded.
C4
Press [왗] CURSOR button.
2
• • • • • • •
Use [왗] and [왘] CURSOR
to move left and right.
Monitoring the data on the display, use [왗] and
[왘] CURSOR buttons to move the input point to
the data you want to change.
Example: To re-record all note data following the note
A3 located at Measure 120, Beat 1, Clock 0.
No t e A3
Recording track
Not recording track
Correcting Mistakes While Step
Recording
Memory data can be thought of as a musical score that
progresses from left to right, with the input point normally
at the far right of the recorded data.
The procedure described here lets you move the input point
to the left in order to make changes in data you have already
input. Note, however, that moving the input point to the left
and changing data automatically deletes all of the data
recorded to the right of the input point.
Measure 120/Beat 1/Clock 0
(Input point moved to using [왗] and [왘] CURSOR buttons)
Data flow
•••••••
• • • • • • •
A3
3
Press the [왔] CURSOR button.
Rew r i t e ?
E-69
735A-E-071B
WK3100_e_61-73.p65
C4
69
04.3.26, 0:11 PM
Song Memory Function
SONG MEMORY
CURSOR
[+]/[–]
YES/NO
START/STOP
4
Press the YES button.
• This deletes all data from the location you specified
and enters step record standby.
• Pressing the [왖] CURSOR button or the NO button
cancels deleting the data.
Measure 120/Beat 1/Clock 0
(Step re-recording begins from here.)
Data flow
•••••••
All data to
the right
is deleted.
NOTE
• When you reach the end of the recording by pressing
the [왘] CURSOR button, the “REC” indicator appears
and the “STEP” indicator flashes on the display,
indicating that you can add more data using step
recording.
SONG MEMORY TRACK
Editing Memory Contents
After you record to keyboard memory, you can recall
individual notes and parameter settings (such as tone
number) and make any changes you want. This means you
can correct misplayed notes, make changes in tone selections,
etc.
The following types of data can be edited.
• Note intensity
• Notes
• Chords
• Tone numbers
• Rhythm number
• INTRO/ENDING 1 button, INTRO/ENDING 2 button,
VARIATION/FILL-IN 1 button, VARIATION/FILL-IN 2
button, SYNCHRO/FILL-IN NEXT button operations
To edit memory contents
1
To delete specific note data
1
2
3
Press the SONG MEMORY button three times to
enter step recording standby, and then use the [+]
and [–] buttons to select a song number (0 to 4).
Flash
Perform steps 1 and 2 under “To correct mistakes
while step recording” above to display the note you
want to delete.
S t e p Re c
Press the [왔] CURSOR button twice.
In response to the “Delete?” message that appears
on the screen, press the YES button to delete the
displayed note.
2
3
Use the SONG MEMORY TRACK buttons to select
the recorded track that you want to edit.
Press the [왗] CURSOR button to enter the editing
mode.
• The REC indicator disappears from the display, and
the STEP indicator flashes.
E-70
WK3100_e_61-73.p65
735A-E-072A
70
04.3.26, 0:11 PM
Song Memory Function
4
Use the [왗] and [왘] CURSOR buttons to move to
the location in track where the note or parameter
you want to change is located.
Note editing example
Velocity
Pitch Parameter being
edited
No t e C4
Editing Techniques and Display
Contents
The following describes the editing techniques you can use
to change the various parameters stored in memory.
To change the key pressure (velocity) of a note
Use the number buttons or [+] and [–] to adjust the key
pressure.
No t e G4
5
Make any changes in the value that you want.
• The actual procedures you use to change a parameter
depend on the type of data it contains. See “Editing
Techniques and Display Contents” on this page for
details.
6
7
To change the pitch of a note
Input a new note on the keyboard or use [+] and [–] buttons
to change the pitch of a note. The pitch you specify here is
reflected in the keyboard and the notes shown in the staff on
the display.
No t e G4
Repeat steps 4 and 5 to edit other parameters.
Press the START/STOP button to end editing when
you are finished.
NOTE
• The only parameters that can be editted for Tracks 2
through 6 are notes and tone numbers.
• In the case of real-time recording, you later can change
tone numbers you specified while recording to Tracks 1
through 6 is in progress.
• You can only change tone numbers that were originally
set for Tracks 2 through 6 using step recording.
• In the case of real-time recording, you later can change
rhythm numbers you specified while recording to Track
1 is in progress.
• You can only change rhythm numbers that were originally
set for Track 1 using step recording.
• You cannot use the edit procedure to add more data to
a recording.
• You cannot move portions of a recording to a different
location within the recording.
• Note lengths cannot be changed.
IMPORTANT!
• Whenever editing memory contents, never change a
note so it is identical to the note before or after it. Doing
so may alter the length of the changed note and the
note before or after it. Should this happen, you will have
to re-record the entire track.
To change a chord
Use the chord fingering method selected by the MODE button
(Fingered, CASIO Chord, etc.) to input a chord.
Ch o r d
To change a tone number
Use the number buttons or [+] and [–] buttons to change a
tone number.
G r a n dPn o
E-71
735A-E-073A
WK3100_e_61-73.p65
71
04.3.26, 0:11 PM
Song Memory Function
SONG MEMORY
CURSOR
[+]/[–]
YES/NO
SONG MEMORY TRACK
Editing a Song
NOTE
• In the case of real-time recording, you later can change
tone numbers you specified while recording to Tracks 1
through 6 is in progress.
• You can only change tone numbers that were originally
set for Tracks 2 through 6 using step recording.
To change a rhythm number
Use the number buttons or [+] and [–] buttons to change a
rhythm number.
Pop
You can perform the following operations in the song editing
mode.
• Delete a song
• Delete a track
• Song header data rewrite (Panel Record)
To delete a song
1
2
NOTE
• In the case of real-time recording, you later can change
rhythm numbers you specified while recording to Track
1 is in progress.
• You can only change rhythm numbers that were originally
set for Track 1 using step recording.
3
Use the [+] and [–] buttons to select the number of
the song you want to delete.
Press the [왔] CURSOR button. If there is no song
number on the display, press the [왔] CURSOR
button twice.
• This displays the song delete screen.
4
Press the YES button.
• This causes the message “Sure?” to appear, confirming
whether you really want to delete the song.
To change a rhythm controller operation*
* INTRO/ENDING 1 button, INTRO/ENDING 2 button,
VARIATION/FILL IN 1 button, VARIATION/FILL IN 2
button, SYNCHRO/FILL IN NEXT button operations
Press the rhythm controller button you want to change to.
Press the SONG MEMORY button once to enter
playback standby.
5
Press the YES button to delete the song and return
to playback standby.
I n t / End1
E-72
WK3100_e_61-73.p65
735A-E-074A
72
04.3.26, 0:11 PM
Song Memory Function
To delete a specific track
1
2
3
To rewrite song header data (Panel
Record)
Press the SONG MEMORY button once to enter
playback standby.
You can use a procedure called “Panel Record” to change the
initial Mixer, tempo and other settings stored in the song
header.
Use the [+] and [–] buttons to select the number of
the song that contains the track you want to delete.
1
Press the [왔] CURSOR button twice. If there is no
song number on the display, press the [왔] CURSOR
button three times.
2
• This displays the song delete screen.
Number of the song that contains the track
(cannot be changed)
Track delete standby
T r . De l . ?
4
3
4
Press the SONG MEMORY button once to enter
playback standby.
Use the [+] and [–] buttons to select the number of
the song that contains the header data you want to
rewrite.
Make the changes you want to the header data.
Press the [왔] CURSOR button three times.
• This displays the song delete screen.
5
Press the YES button to rewrite the header data.
Use the SONG MEMORY TRACK buttons to select
the recorded track or tracks whose data you want
to delete.
Track delete standby
Recorded track
Track being deleted (Multiple
tracks can be specified.)
• You can specify more than one track for deletion by
pressing more than one track select button.
• To deselect a track, simply press its track select button
again.
5
Press the YES button.
• This causes the message “Sure?” to appear, confirming
whether you really want to delete the track.
6
Press the YES button to delete the track.
NOTE
• You cannot change the song number while in track delete
standby.
• Pressing the SONG MEMORY button while in track
delete standby returns to record standby.
E-73
735A-E-075A
WK3100_e_61-73.p65
73
04.3.26, 0:11 PM
Keyboard Settings
SPLIT
2
Parts
Press the LAYER button.
Selected layer tone
Up to four parts (numbered 1 through 4) can be used
simultaneously during keyboard play. These parts can be
used by the layer and split functions explained below.
Part 1: Main tone part
Part 2: Layered tone part
Part 3: Split tone part
Part 4: Layered and split tone part
3
Select the layered tone.
Example: To select “360 FRENCH HORN GM” as the
layered tone, use the number buttons to input 3, 6 and then 0.
Layer lets you assign two different tones (a main tone and a
layered tone) to the keyboard, both of which play whenever
you press a key. For example, you could layer the FRENCH
HORN GM tone on the BRASS GM tone to produce a rich
and brassy sound.
F r . Ho r nG
4
LAYER
Now try playing something on the keyboard.
• Both tones are played at the same time.
5
Main Tone (BRASS GM) + Layered Tone (FRENCH HORN GM)
To layer tones
First select the main tone.
Example: To select “361 BRASS GM” as the main tone,
press the TONE button and then use the number buttons to input 3, 6 and then 1.
B r a s s _G
Press the LAYER button again to unlayer the tones
and return the keyboard to normal.
NOTE
• Turning on layering switches the currently selected part
from Part 1 to Part 2, and displays the layered tone. At
that time, you can use the [왗] and [왘] CURSOR buttons
to switch between parts. Turning off layering returns to
Part 1.
• The main tone sounds over Channel 1, while the layered
tone sounds over Channel 2. You can also use the Mixer
to change the tone and volume settings for these
channels.
• Note that layering is not possible during record standby
or recording in the Song Memory Mode, or while you
are using the SMF Player Mode.
E-74
WK3000_e_74-88.p65
Lit
S t r i ngs1
Using Layer
1
LAYER
735A-E-076A
74
04.3.26, 0:11 PM
Keyboard Settings
4
Using Split
With split you can assign two different tones (a main tone
and a split tone) to either end of the keyboard, which lets
you play one tone with your left hand and another tone with
your right hand. For example, you could select STRINGS 1as
the main (high range) tone and PIZZICATO GM as the split
(low range) tone, putting an entire string ensemble at your
fingertips.
Split also lets you specify the split point, which is the location
on the keyboard where the changeover between the two tones
occurs.
Example: To specify G3 as the split point, press the G3
key.
G3
5
NOTE
• Leave the MODE button in the Normal or FULL RANGE
CHORD position.
SPLIT
Specify the split point. While holding down the
SPLIT button, press the keyboard key where you
want the leftmost key of the high end range to be.
6
Now try playing something on the keyboard.
• Every key from F 3 and below is assigned the
PIZZICATO GM tone, while every key from G3 and
above is assigned the STRINGS 1 tone.
Press the SPLIT button again to unsplit the keyboard
and return it to normal.
NOTE
Split Tone
(PIZZICATO GM)
Main Tone (STRINGS 1)
Split point
To split the keyboard
1
First select the main tone.
Example: To select “348 STRINGS 1” as the main tone,
press the TONE button and then use the
number buttons to input 3, 4 and then 8.
• Turning on split switches the currently selected part to
Part 3, and displays the split tone. At that time, you can
use the [왗] and [왘] CURSOR buttons to switch between
parts. Turning off split returns to Part 1.
• The main tone sounds over Channel 1, while the split
tone sounds over Channel 3. You can also use the Mixer
to change the tone and volume settings for these
channels.
• Note that split is not possible during record standby or
recording in the Song Memory Mode, or while you are
using the SMF Player Mode.
• When the MODE button is set to CASIO CHORD or
FINGERED, the accompaniment keyboard range is in
accordance with the split point you specify with the above
procedure.
S t r i ngs1
2
Press the SPLIT button.
Selected split tone
Lit
A c o . B s _G
3
Select the split tone.
Example: To select “345 PIZZICATO GM” as the split
tone, use the number buttons to input 3, 4 and
then 5.
P i z z _G
E-75
735A-E-077B
WK3000_e_74-88.p65
75
04.3.26, 0:11 PM
Keyboard Settings
TONE
TRANSPOSE/FUNCTION
[+]/[–]
SPLIT
Using Layer and Split Together
You can use layer and split together to create a layered split
keyboard. It makes no difference whether you layer tones
first and then split the keyboard, or split the keyboard and
then layer tones. When you use layer and split in combination,
the high range of the keyboard is assigned two tones (main
tone + layered tone), and the low range two tones (split tone
+ layered split tone).
LAYER
To split the keyboard and then layer
tones
1
Press the TONE button and then input the tone
number of the main tone.
Example: To set “361 BRASS GM” as the main tone.
B r a s s _G
LAYER SPLIT
2
Press the SPLIT button and then input the number
of the split tone.
Example: To set “345 PIZZICATO GM” as the split tone.
Split Tone (PIZZICATO GM)
+
Layered Split Tone
(STRINGS 1)
Main Tone (BRASS GM)
+
Layered Tone (FRENCH HORN GM)
P i z z _G
Split point
• After specifying the split tone, press the SPLIT button
to unsplit the keyboard.
3
Press the LAYER button and then input the number
of the layered tone.
Example: To set “360 FRENCH HORN GM” as the
layered tone.
F r . Ho r nG
4
Press the SPLIT button or the LAYER button so both
of the SPLIT and LAYER indicators are displayed.
E-76
WK3000_e_74-88.p65
735A-E-078A
76
04.3.26, 0:11 PM
Keyboard Settings
5
Input the number of the layered split tone.
Example: To specify the “348 STRINGS 1” tone, enter 3,
4, 8.
S t r i ngs1
6
7
While holding down the SPLIT button, press the
keyboard key where you want the lowest note (the
leftmost key) of the upper range (right side range)
to be.
Transposing the Keyboard
Transpose lets you raise and lower the overall key of the
keyboard in semitone units. If you want to play an
accompaniment for a vocalist who sings in a key that’s
different from the keyboard, for example, simply use
transpose to change the key of the keyboard.
To transpose the keyboard
1
Press the TRANSPOSE/FUNCTION button.
• This causes a pointer to appear on the display next to
TRANSPOSE/FUNCTION, and displays the
transpose setting screen.
Play something on the keyboard.
• Press the LAYER button to unlayer the keyboard, and
the SPLIT button to unsplit it.
T r ans .
NOTE
• Turning on layer+split switches the currently selected
part to Part 4, and displays the layered tone. At that
time, you can use the [왗] and [왘] CURSOR buttons to
switch between parts. Turning off layer returns to Part
3, while turning off split returns to part 2. Turning off
both layer and split returns to Part 1.
• The main tone sounds over Channel 1, the layer tone
over Channel 2, the split tone over Channel 3, and the
layer/split tone over Channel 4. You can also use the
Mixer to change the tone and volume settings for these
channels.
2
Use [+] and [–] to change the transpose setting of
the keyboard.
Example: To transpose the keyboard five semitones
upwards.
T r ans .
• Pressing the TRANSPOSE/FUNCTION button exits
the transpose screen.
NOTE
• The keyboard can be transposed within a range of –24
(two octave downwards) to +24 (two octave upwards).
• The transpose setting also affects playback from song
memory and Auto Accompaniment.
• The allowable pitch range you can transpose within
depends on the tone you are using. If a transpose
operation causes a note to be outside of the pitch range
for the tone being used, the keyboard automatically plays
the same note in the nearest octave that falls within the
pitch range of the tone you are using.
E-77
735A-E-079B
WK3000_e_74-88.p65
77
04.3.26, 0:11 PM
Keyboard Settings
TRANSPOSE/FUNCTION
CURSOR
[+]/[–]
Using Touch Response
Tuning the Keyboard
When touch response is turned on, the relative volume of
sound output by the keyboard is varied in accordance with
the amount of pressure applied, just like an acoustic piano.
The tuning feature lets you fine tune the keyboard to match
the tuning of another musical instrument.
To turn touch response on and off
1
Press the TRANSPOSE/FUNCTION button.
• This causes a pointer to appear on the display next to
TRANSPOSE/FUNCTION.
2
1
2
Press the TRANSPOSE/FUNCTION button.
Use the [왗] and [왘] CURSOR buttons to display
the tuning screen.
Use the [왗] and [왘] CURSOR buttons to display
the touch response setting screen.
Touch
3
To tune the keyboard
Use the [+] and [–] buttons to select the touch
response sensitivity level.
• “1” outputs powerful sound even with light key
pressure, while “3” requires very heavy key pressure
to output powerful sound.
• Pressing [+] and [–] at the same time returns
sensitivity to the “2” setting.
• When you select “oFF”, the tone does not change
regardless of how much pressure you apply to the
keyboard.
NOTE
• Touch response not only affects the keyboard’s internal
sound source, it also is output as MIDI data.
• Song Memory playback, accompaniment, and external
MIDI note data do not affect the touch response setting.
Tune
3
Use [+] and [–] to change the tuning setting of the
keyboard.
Example: To lower the tuning by 20.
Tune
• Pressing the TRANSPOSE/FUNCTION button exits
the transpose screen.
NOTE
• The keyboard can be tuned within a range of –99 cents
to +99 cents.
*100 cents is equivalent to one semitone.
• The tuning setting also affects playback from song
memory and Auto Accompaniment.
E-78
WK3000_e_74-88.p65
735A-E-080B
78
04.3.26, 0:11 PM
Keyboard Settings
Changing Other Settings
Setting Types
The table below shows the parameters whose settings you can change.
Setting menu
Description
Page
Transpose
(Trans.)
Adjusts of overall keyboard tuning by semitone units.
E-77
Auto Harmonize
(AutoHarm)
Selects the Auto Harmonize Type
E-82
Touch Response
(Touch)
Specifies of how sound should change with keyboard pressure.
E-78
Tune
(Tune)
Fine adjustment of overall keyboard tuning.
E-78
Display
(Contrast)
Adjusts display brightness.
E-82
Pedal
(Jack)
Assigns effects to pedals.
E-82
Mixer Hold
(MixHold)
Turns mixer hold on or off.
E-82
DSP Hold
(DSP Hold)
Turn DSP hold on or off.
E-82
MIDI
(MIDI)
MIDI settings
E-82
Delete/Initialize
(Del/Init)
Initializes all settings to initial factory defaults, resets specific settings or deletes user
rhythms.
E-83
NOTE
• The above settings are all saved whenever you turn off the keyboard. For details, see “Memory Contents” on page E-18.
• MIDI settings and Delete/Initialize settings are disabled while you are using the SMF Player or Song Memory function.
E-79
735A-E-081B
WK3000_e_74-88.p65
79
04.3.26, 0:11 PM
Keyboard Settings
To use the keyboard settings menu
1
Press the TRANSPOSE/FUNCTION button.
• This causes a pointer to appear on the display next to TRANSPOSE/FUNCTION.
2
Use the [왗] and [왘] CURSOR buttons, and the [왖] and [왔] CURSOR buttons to recall the items whose settings
you want to change.
Tone selection screen
TRANSPOSE/FUNCTION
button
EXIT button
TRANSPOSE/FUNCTION button
[왘] *
[왘]
[왘]
[왘]
[왘]
[왗]
[왗]
[왗]
[왗]
[왗]
[왘]
[왘]
[왗]
[왗]
[왔]
[왖]
MIDI setting
[왘]
[왘]
[왘]
[왘]
[왗]
[왗]
[왗]
[왗]
[왔]
[왖]
Delete setting
[왘]
[왘]
[왗]
[왗]
[왘]
[왘]
[왗]
[왗]
[왖]
[왔]
Initialize
setting
*
[왖] : [왖] CURSOR button
[왔] : [왔] CURSOR button
E-80
WK3000_e_74-88.p65
[왗] : [왗] CURSOR button
[왘] : [왘] CURSOR button
735A-E-082A
80
04.3.26, 0:11 PM
Keyboard Settings
TRANSPOSE/FUNCTION
CURSOR
Number buttons
[+]/[–]
YES/NO
EXIT
3
Use the [+] and [–] buttons or the number buttons to change the values.
• Settings you make are applied even if you do not press the EXIT button.
• See the following section titled “Setting Menu Items” for details on each setting.
• After making the settings you want, press the TRANSPOSE/FUNCTION button or EXIT button to return to the tone or
rhythm selection screen.
■ In case of a delete or initialize procedure
4
Press the YES button.
• This displays the user area number and data name of the data to be deleted.
• The data size value represents kilobyte units.
5
6
Now use the number buttons, or the [+] (increase) and [–] (decrease) buttons to select the data you want.
Press the [왔] CURSOR button.
• This causes the message “Sure?” to appear, confirming whether you really want to perform the delete or initialize operation.
7
Press the YES button to complete the operation.
• This performs the delete or initialize operation and returns to the step 5 screen.
8
After making the settings you want, press the TRANSPOSE/FUNCTION button or EXIT button to return to the tone
or rhythm selection screen.
IMPORTANT!
• It can take more than one minute to perform a delete or initialize procedure after you pressing the YES button in step 7
above. The message “Pls Wait” will remain on the display to indicate that a procedure is being performed. Never try to
perform any operation while “Pls Wait” is displayed. Performing any operation can damage the keyboard’s memory and
cause it to malfunction.
E-81
735A-E-083B
WK3000_e_74-88.p65
81
04.3.26, 0:11 PM
Keyboard Settings
Setting Menu Items
쏋 Auto Harmonize Types
You can select from among the 10 different types of auto harmonize listed below.
No.
Type
(Parameter Name)
Description
0
Duet1
Adds a 1-part harmony to keyboard play.
1
Duet2
Adds a 1-part harmony to keyboard play. Duet2 harmony is more open than Duet1.
2
Country
Adds a country-flavor harmony to keyboard play.
3
Octave
Adds notes one octave below notes played on the keyboard.
4
5th
Adds fifth notes above notes played on the keyboard.
5
3-Way Open
Adds two open harmony parts to notes played on the keyboard (creating three-part harmony).
6
3-Way Close
Adds two close harmony parts to notes played on the keyboard (creating three-part harmony).
7
Strings
Adds harmony suitable for strings.
8
Block
Adds block chord notes.
9
Big Band
Adds harmony suitable for big band play.
쏋 Other Settings
Setting menu
Contrast
(Contrast)
Assignable Jack
(Jack)
Mixer Hold
(MixHold)
DSP Hold
(DSP Hold)
Range
Default
Description
00 to 15
07
SUS
SUS
SoS
—
Assigns the sostenuto pedal effect to a pedal.
SFt
—
Assigns the soft pedal effect to a pedal.
rhy
—
Assigns the START/STOP button function to a pedal.
on/oFF
oFF
When Mixer Hold is turned on, the parameters of accompaniment
parts (Part 6 through Part 10) cannot be modified by
accompaniment data.
on/oFF
oFF
on: Current DSP line setting is maintained, even when the tone is
changed.
oFF: Changing the tone switches to the DSP line setting of the new
tone.
Description
Adjusts display contrast.
Assigns the sustain pedal effect to a pedal.
쏋 MIDI Setting
Range
Default
Keyboard Channel
(Keybd Ch)
Setting menu
01 to 16
01
MIDI In Chord Judge
(Chord)
on/oFF
oFF
Specifies whether accompaniment range MIDI Note On messages
received from an external device should be interpreted as auto
accompaniment chords.
Accomp/Song MIDI Out
(Ac/SgOut)
on/oFF
oFF
Specifies whether this keyboard’s auto accompaniment or song
memory is sent as MIDI messages.
Local Control Setting
(Local)
on/oFF
on
Specifies whether the keyboard should sound the parts played on
it.
Pitch Bend Range
(Bend)
00 to 12
12
Specifies the maximum change in a tone that can be applied using
the PITCH BEND wheel. The setting range is 00 (no change) to 12
(12 semitones).
Specifies the send channel for main tone play.
E-82
WK3000_e_74-88.p65
735A-E-084A
82
04.3.26, 0:11 PM
Keyboard Settings
쏋 Delete/Initialize Settings
Range
Default
SMF Delete
Setting menu
—
—
Deletes selected SMF data.
Description
User Rhythm Delete
—
—
Deletes selected user rhythm data.
User Tone Delete
—
—
Deletes selected user tone data.
Mixer Reset
(InitMix?)
—
—
Initializes parameters assigned by the Mixer or by input from an
external sequencer.
Parameter Reset
(InitPar?)
—
—
System Reset
(InitSys?)
—
—
Initializes all parameters, except for the display contrast setting.
Initializes to initial factory defaults.
Deletes all data in the user area.
E-83
735A-E-085A
WK3000_e_74-88.p65
83
04.3.26, 0:11 PM
Using the SMF Player
The letters “SMF” stand for Standard MIDI File, which is a file format that allows MIDI data to be shared between different
software and sequencers. There are actually three SMF formats, named SMF 0, SMF 1, and SMF 2. This keyboard supports the
SMF 0 format, which is the one that is most widely used today, and so all mentions of “SMF data” in this manual refer to SMF 0
format data.
SMF format music data can be stored in the keyboard’s built-in Flash memory. Data stored in Flash memory can be played back
using the SMF Player Mode. You can also load SMF data from a SmartMedia card or floppy diskette into the keyboard’s user area
and then play it back using the SMF Player Mode. The follow shows the maximum number of files that can be stored on each type
of media.
Flash Memory: 200 files*
SmartMedia Card: 255 files*
Floppy Diskette (WK-3500 only): 112 (2DD diskette)* or 224 (2HD diskette) files*
* Note that the number of files you can store in memory also depends on the size of each file. If your files are very large, you may
be able to store fewer than the number of files indicated above.
IMPORTANT!
• Note that CASIO COMPUTER CO., LTD. shall not be held liable for any loss of data stored in Flash memory, or on a
SmartMedia card or a floppy diskette (WK-3500 only).
E-84
WK3000_e_74-88.p65
735A-E-086B
84
04.3.26, 0:11 PM
Using the SMF Player
SMF Player Mode Operational Flow
Tone/Rhythm Selection Screen
SMF PLAYER button
SMF PLAYER button
Select media.
SMF Player indicator Lights
[왖]*
EXIT button
[왖]
Select file name.
S1
ABC1
[왘]*, [+]
S1
Playback Mode + File Name
[왗], [–]
ABC2
[왘], [+]
Playback Mode + File Name
START/STOP button
[왗], [–]
S1
ABC3
Playback Mode + File Name
[왔]
EXIT button, [왖]
Select play along part.
Key Ch
01
[왘], [+]
EXIT button
Part Number
[왗], [–]
Key Ch
04
[왘], [+]
[왗], [–]
Key Ch
16
START/STOP button
Part Number
Part Number
Direct input using number buttons is also possible.
[왔]
[왖]
Select playback mode.
PlayMode
S1
[왘], [+]
EXIT button
Playback Mode
[왗], [–]
PlayMode
SL
[왘], [+]
[왗], [–]
PlayMode
A1
[왘], [+]
Playback Mode
[왗], [–]
PlayMode
AL
START/STOP button
Playback Mode
Playback Mode
[왔]
[왖]
Note
• You can use the [왘],
[왗], [+], [–] buttons to
control SMF play back.
Select output mode.
Output
int
EXIT button
[왘], [+]
out
OUTPUT
START/STOP button
[왗], [–]
Output
OUTPUT
START/STOP button, Playback complete.
Select music
04
ABC 1
Part Number + File Name
Playback stopped.
*
Error (Other errors may also occur.)
[왖] : [왖] CURSOR button
[왔] : [왔] CURSOR button
[왗] : [왗] CURSOR button
[왘] : [왘] CURSOR button
Data is SMF but not SMF0
Err
Not SMF0
SMF0 error appears
Data is not correct SMF
Err
WrongDat
Data error appears
E-85
735A-E-087A
WK3000_e_74-88.p65
EXIT button
85
04.3.26, 0:11 PM
Using the SMF Player
SMF PLAYER
CURSOR
Number buttons
[+]/[–]
ACCOMP VOLUME
START/STOP
Playing Back an SMF
EXIT
To play back an SMF
Note that the first step you need to perform in the procedure
below depends on whether you are playing back from Flash
memory, a SmartMedia card, or a floppy diskette (WK-3500
only).
1
PREPARATION
Flash Memory
• SmartMedia Card
• Insert the SmartMedia card that contains the data you
want to play into the keyboard’s card slot.
• Floppy Diskette (WK-3500 Only)
• Insert the floppy diskette that contains the data you
want to play into the keyboard’s floppy disk drive.
What you should do first depends on whether you
are playing back from Flash memory, a memory
card, or a floppy diskette.
2-1
Use the SMF PLAYER button to display the
“Internal” indicator in the text area of the screen.
• This causes the “SMF PLAYER” indicator to appear
on the display.
I n t e r na l
IMPORTANT!
• Never remove the SmartMedia card from the card slot
or turn off the keyboard while card data is being accessed
by a save, read, or delete operation. Doing so can corrupt
the data on the SmartMedia card or even damage the
card slot.
• Before ejecting a diskette, always check to make sure
that the access lamp is not lit or flashing. A lit or flashing
access lamp means that the keyboard is performing a
data read or write operation. Ejecting a diskette while it
is being accessed can cause its data to become
corrupted.
SmartMedia Card
2-2
Insert the SmartMedia card that contains the file
you want to play into the keyboard’s card slot.
Use the SMF PLAYER button to display the “Card”
indicator in the text area of the screen.
• This causes the “SMF PLAYER” indicator to appear
on the display.
Floppy Diskette (WK-3500 only)
2-3
Insert the floppy diskette that contains the file
you want to play into the keyboard’s floppy disk
drive. Use the SMF PLAYER button to display the
“Disk” indicator in the text area of the screen.
• This causes the “SMF PLAYER” indicator to appear
on the display.
3
Press the [왔] CURSOR button to display the file
selection screen.
• SMFs are those shows file names end with the
extension “MID”. An error message appears at this
time if there are no SMF files currently in Flash
Memory.
E-86
WK3000_e_74-88.p65
735A-E-088A
86
04.3.26, 0:11 PM
Using the SMF Player
4
Use the [왗] and [왘] CURSOR buttons or the [+]
and [–] buttons to select the file you want to play.
• The name of the currently selected file appears in the
text area of the display. The playback mode is shown
in the number area of the display. The Tempo/
Measure area of the display shows the size of the file
in kilobytes.
5
To configure other settings
1
2
Adjusting SMF Playback Volume
1
NOTE
• Entering the SMF Player Mode initializes all parts by
turning on all Mixer Mode channels.
Press the ACCOMP VOLUME button.
• This causes the “SMF Vol.” indicator to appear on the
display, along with a value that indicates the current
SMF volume setting.
2
Press the [왔] CURSOR button to display a screen
for selecting the part you want to play on the
keyboard (play along part).
• Use the [왗] and [왘] CURSOR buttons or the [+] and
[–] buttons to select the play along part.
• You can specify the part you want to play on the
keyboard (the play-along part) as a value in the range
of 1 through 16.
• After specifying a part, turn off the channel that
corresponds to the play-along part you selected. See
“Turning Channels On and Off” on page E-47 for more
information. Performing this step turns off the
applicable part so you can play it on the keyboard
along with the rest of the SMF playback.
To stop file playback, press the START/STOP button
again.
The following procedure explains how to control the overall
volume of SMF data playback. You can adjust volume while
playback is stopped or ongoing.
Select the file you want to play back.
• Perform steps 1 through 3 under “To play back an
SMF” to select a file.
Press the START/STOP button
• This starts playback of the selected file.
• The number area of the display shows the number of
the part to be played manually on the keyboard.
• You can use the TEMPO buttons to adjust the tempo
within the range of 30 to 255.
• You can turn channels 1 through 16 on and off,
regardless of whether file playback is in progress or
stopped. For more information, see “Turning
Channels On and Off” on page E-47.
6
Configuring Other Settings
3
Use the [+] and [–] buttons or the number buttons
to adjust the SMF volume.
Press the [왔] CURSOR button to display the
playback mode selection screen. Use the [왗] and
[왘] CURSOR buttons or the [+] and [–] buttons to
select the playback mode.
You can select from among the following four playback
modes.
• You can specify a setting in the range of 000
(minimum) to 127 (maximum).
• Pressing [+] and [–] at the same time returns the SMF
volume setting to 100.
• Note that this setting does not affect the volume of
the notes you play on the keyboard.
S1 : One file, one time
SL : One file, repeat
A1 : All files, one time
AL : All files, repeat
4
Press the [왔] CURSOR button to display the output
mode selection screen.
• Use the [왗] and [왘] CURSOR buttons or the [+] and
[–] buttons to select the output mode.
• You can select from among the following two output
types.
int : Keyboard’s built-in speakers
out : MIDI OUT
NOTE
• Layer, split, and Auto Harmonize are automatically turned
off in the SMF Player Mode.
E-87
735A-E-089B
WK3000_e_74-88.p65
87
04.3.26, 0:11 PM
Using the SMF Player
SMF Player Error Messages
The following explains what you should do when an error message appears in the SMF Player Mode.
Error Message
Cause
Action
Err Not SMF0
You are attempting to play SMF data that is
not Format 0.
Use only Format 0 SMF data.
Err WrongDat
There is a problem with the SMF data you are
trying to play or the data is corrupted.
Use different data.
E-88
WK3000_e_74-88.p65
735A-E-090A
88
04.3.26, 0:11 PM
MIDI
What is MIDI?
MIDI Channels
The letters MIDI stand for Musical Instrument Digital
Interface, which is the name of a worldwide standard for
digital signals and connectors that make it possible to
exchange musical data between musical instruments and
computers (devices) produced by different manufacturers.
MIDI compatible equipment can exchange keyboard key
press, key release, tone change, and other data as messages.
Though you do not need any special knowledge about MIDI
to use this keyboard as a stand-alone unit, MIDI operations
require a bit of specialized knowledge. This section provides
you with an overview of MIDI that will help to get you going.
MIDI Connections
MIDI messages are send out through the MIDI OUT terminal
of one device to the MIDI IN terminal of another machine
over a MIDI cable. To send a message from this keyboard to
another device, for example, you must use a MIDI cable to
connect the MIDI OUT terminal of this keyboard to the MIDI
IN terminal of the other device. To send MIDI messages back
to this keyboard, you need to use a MIDI cable to connect the
other device’s MIDI OUT terminal to the MIDI IN terminal
of this keyboard.
To use a computer or other MIDI device to record and
playback the MIDI data produced by this keyboard, you must
connect the MIDI IN and MIDI OUT terminals of both devices
in order to send and receive data.
MIDI IN
MIDI OUT
MIDI IN
MIDI OUT
MIDI allows you to send the data for multiple parts at the
same time, with each part being sent over a separate MIDI
channel. There are 16 MIDI channels, numbered 1 through
16, and MIDI channel data is always included whenever you
exchange data (key press, pitch bend operation, etc.).
Both the sending device and the receiving machine must be
set to the same channel for the receiving device to correctly
receive and play data. If the receiving device is set to Channel
2, for example, it receives only MIDI Channel 2 data, and all
other channels are ignored.
This keyboard is equipped with multi-timbre capabilities,
which means it can receive messages over all 16 MIDI
channels and play up to 16 parts at the same time. Tone and
volume settings for each channel can be made using the
keyboard’s onboard Mixer, or by an external source that sends
required MIDI control messages.
Keyboard operations performed on this keyboard are sent
out by selecting a MIDI channel (1 to 16) and then sending
the appropriate message.
General MIDI
General MIDI standardizes MIDI data for all sound source
types, regardless of manufacturer. General MIDI specifies
such factors as tone numbering, drum sounds, and available
MIDI channels for all sound sources. This standard makes it
possible for all MIDI equipment to reproduce the same
nuances when playing General MIDI data, regardless of the
manufacturer of the sound source.
This keyboard supports General MIDI, so it can be used to
play commercially available pre-recorded General MIDI data
and General MIDI data send to it from a personal computer.
See the “Tone List” on page A-1 for details about the tones
that are available with GM tones numbered 000 to 127.
Computer etc.
If a MIDI THRU function provided by the software is being
run on a connected computer or other MIDI device, be sure
to turn this keyboard’s “Local Control Setting” off (page E82).
E-89
735A-E-091B
WK3100_e_89-105.p65
89
04.3.26, 0:11 PM
MIDI
Sending and Receiving MIDI
Messages
This keyboard can send notes you play on the keyboard, as
well as auto accompaniment patterns and Song Memory
playback as MIDI messages to another device.
MIDI Settings
You can change the settings of a number of parameters that
control how MIDI messages are sent and received.
MIDI Parameters
MIDI Send Data
■ Keyboard Play
Each keyboard part (Channels 1 through 4) is sent over its
own individual MIDI channel. When Auto Harmonize is
turned on, harmonize notes are also sent over each individual
MIDI channel.
■ Auto Accompaniment or Song Memory Play
Each accompaniment part is sent over its own individual
MIDI channel. The “Accomp/Song MIDI Out” parameter
(page E-82) is used to specify whether a part is sent.
You can use the parameter setting procedure (page E-80) to
change the settings of the MIDI parameters described below.
See pages E-80 to E-83 for details about the setting menu and
procedure.
■ MIDI In Chord Judge
This parameter determines whether note data received from
an external device should be interpreted as an auto
accompaniment chord fingering. Turn on this parameter
when you want to control auto accompaniment chords from
a computer or other external device.
on: Causes note data input through MIDI IN to be
interpreted as auto accompaniment chord fingerings.
The channel specified by the keyboard channel is used
for specifying chords.
oFF: Turns off “MIDI In Chord Judge”.
MIDI Message Receive
■ Multi Channel Receive
The 16 mixer parts can be used to receive data over 16 MIDI
message channels at the same time.
■ Accomp/Song MIDI Out (Accompaniment/Song MIDI Out)
Turn on this parameter when you want sound auto accompaniment or Song Memory on an external devices sound
source.
■ Chord Changes when Using Auto Accompaniment
MIDI messages received from an external device can be
interpreted as chord changes as specified by the fingerings
supported by the auto accompaniment system of this
keyboard. Use the “MIDI In Chord Judge” parameter (page
E-82) to turn this capability on and off.
on: Outputs auto accompaniment or Song Memory as MIDI
messages through the keyboard’s MIDI OUT terminal.
• See the MIDI Implementation Chart at the back of this
User ’s Guide for more information about each MIDI
message.
oFF: Does not output auto accompaniment or Song Memory.
NOTE
• For details about MIDI specifications, visit the CASIO
Website.
http://world.casio.com
E-90
WK3100_e_89-105.p65
735A-E-092A
90
04.3.26, 0:11 PM
MIDI
Using the Data Download Service
To connect to a computer
You can download the following type of data from CASIO
MUSIC SITE (http://music.casio.com) to your computer, and
then transfer it to the keyboard.
Be sure to turn off the keyboard and your computer before
connecting them. You should also set the volume controller
of the keyboard to a relatively low volume.
• Tones
• Tones with waves
• Drum sets with waves
• DSP
• Rhythms
• Registrations
• Songs
• SMF
• Package File Data
1
Connect the keyboard’s MIDI interface to your
computer’s MIDI interface.
CASIO MUSIC SITE
Internet
Service
Provider
■ Data and Application Software
Data itself as well as application software for transferring data
between your computer and the keyboard are available for
download at the CASIO MUSIC SITE.
■ Application Software
You can run the application software on your computer and
transfer data you download from the CASIO MUSIC SITE to
the keyboard, and also use your computer’s hard disk for
long-term storage of data you transfer from the keyboard to
your computer.
OUT IN
• See the instructions provided at the CASIO MUSIC SITE
for full information about how to download the application
software and data.
• See the application software’s online help for information
about how to use the software.
MIDI Interface
MIDI IN
MIDI OUT
* CASIO MUSIC SITE
http://music.casio.com/
1
2
3
Go to the above URL.
2
Select a region or country.
Select a download service for the INTERNET DATA
EXPANSION SYSTEM data.
• Note that the service you should use depends on the
area or country.
3
Turn on the keyboard, and then turn on your
computer or other connected device.
Start up the software you want to use on your
computer.
NOTE
• When using the application software, make sure that
the tone setting screen (the screen that appears after
turning on power) is on the keyboard’s display screen.
DATA ACCESS Lamp
• The DATA ACCESS lamp lights whenever the keyboard is
exchanging data with a connected computer over a MIDI
cable connection. Never disconnect the MIDI cable while
the DATA ACCESS lamp is lit.
E-91
735A-E-093B
WK3100_e_89-105.p65
91
04.3.26, 0:11 PM
Saving Data
You can save data you create and data you transfer to the keyboard from a computer to the keyboard’s built-in Flash memory, or
to a SmartMedia cardTM or floppy diskette (WK-3500). In this manual, SmartMedia cards and floppy diskettes are referred to as
“external storage media”.
The types of files that can be saved to external storage media are listed below. Note that each type of file can be saved to a specific,
pre-defined user area, as shown in the “Savable File Types” table below.
After you load SMF data from external storage media and store it in a user area, you can play it back using the SMF Player Mode.
See “Using the SMF Player” on page E-84 for more information.
Savable File Types
Display
Indicator
Type
Saved Data
User Memory
Capacity
File Name
Extension
SMF
Smf
1 Tune
200
MID
Rhythm Pattern
Pattern
1 Pattern
16
Z00
Registration
Regist
1 Bank
8
Z01
User song created in the Song Memory Mode
Song
1 Tune
5
Z02
Drum sound with waves
Dr wave
1 Set
4
Z03
Drawbar organ tone
Drawbar
1 Tone
100
Z04
Tone
Tone
1 Tone
100
Z05
Tone with waves
Tn wave
1 Tone
20
Z06
DSP
Dsp
1 Type
100
Z07
Package File*1
Package
1 Pack
1
Z08
All User Data*2
All Data
Z09
*1: Package File
A package file combines tone settings, DSP effect settings, and other setup data into a single file that you can manage and load as
a unit (package). Once you create a package file, you will be able to change the entire setup of the keyboard by loading a single
package file.
To create a package file, you need to download special package file software from the CASIO Music Site (http://music.casio.com/)
and install it on your computer. For details about the package file software, see the information provided at the CASIO Music Site.
IMPORTANT!
• Loading a package file loads the setting data listed in the table under “Package File Data Contents” into the user area, and
replaces all current data with the data in the package file.
• When loading package data from a SmartMedia card or floppy diskette (WK-3500 only), the display’s level meter shows the
progress of the load operation as shown below.
[Load Start]
[Load End]
*2: SmartMedia card only
Package File Data Contents
Data Type
User Area
SMF
10 Songs
Rhythm Patterns
148 to 155 (8 rhythms)
Registrations
7 to 8 (2 banks)
Drum Sound With Waves
803 (1 set)
Drawbar Organ Tones
190 to 199 (10 tones)
Tones
690 to 699 (10 tones)
Tones With Waves
710 to 719 (10 tones)
DSP
190 to 199 (10 effects)
E-92
WK3100_e_89-105.p65
735A-E-094B
92
04.3.26, 0:11 PM
Saving Data
Using a SmartMedia Card
Your keyboard is equipped with a card slot that supports the
use of SmartMediaTM cards that you can use to store tunes
you transfer from your computer, songs you have stored in
the keyboard’s memory, and other data. This provides you
with access to virtually unlimited volumes of data that you
can instantly load whenever you need it.
IMPORTANT!
• There are two types of SmartMedia cards: 3.3V and 5V.
Note that this keyboard supports use of 3.3V type
SmartMedia cards only.
• Never try to use a 5V type SmartMedia card with this
keyboard.
• Note you will not be able to store data to, delete data
from, or rename a SmartMedia card that has a write
protect sticker affixed to the card’s write protect area.
Contacts
Write protect area
About SmartMediaTM Cards
• You can purchase SmartMedia cards at most household
appliance stores, computer stores, etc.
• SmartMedia cards are commercially available in capacities
ranging from 8MB up to 128MB.
• Though a SmartMedia card is about the size of a postage
stamp, its capacity ranges from 8 to 100 times the capacity
of a floppy diskette.
• The data read rate from a SmartMedia card is very fast.
• SmartMediaTM is a trademark of Toshiba Corporation.
SmartMedia Card and Card Slot
Precautions
IMPORTANT!
• Be sure to carefully read all documentation that comes
with the SmartMedia card for important information about
how to handle it.
• Avoid storing and using SmartMedia cards in the
following types of locations. Such conditions can cause
corruption of data stored on the card.
• Areas subject to high temperatures, high humidity, or
corrosive agents
• Areas subject to strong electrostatic charge or
electrical noise
• Whenever handling a SmartMedia card, make sure that
you never touch its contacts with your fingers.
• If the data access lamp is lit and the message “Pls Wait”
is on the display, it means that data on the SmartMedia
card is being accessed by a save, read, or delete
operation. Never remove the SmartMedia card from the
card slot or turn off the keyboard while the card is being
accessed. Doing so can corrupt the data on the
SmartMedia card or even damage the card slot.
• Never try to insert any type of card other than a 3.3V
SmartMedia card into the card slot. Doing so can
damage the keyboard.
• Inserting a SmartMedia card that is charged with static
electricity into the card slot can cause malfunction of
the keyboard. If this happens, turn the keyboard off and
then back on again.
• A SmartMedia card that has been in the card slot for a
long time may feel hot when you remove it. This is normal
and does not indicate malfunction.
• Note that a SmartMedia card has a limited service life.
After long use, you may not be able to store data to,
read data from, and/or delete data from a card. When
this happens, you will need to purchase a new
SmartMedia card.
CASIO COMPUTER CO., LTD. assumes no responsibility
for any loss or damage to you or any third party arising
out of the loss or corruption of data.
E-93
735A-E-095B
WK3100_e_89-105.p65
93
04.3.26, 0:11 PM
Saving Data
Inserting and Removing a
SmartMedia Card
Using the Floppy Disk Drive
(WK-3500 Only)
The following describes how to insert a SmartMedia card into
the card slot and how to remove it.
Floppy Disk Drive Features
To insert a SmartMedia card into the card slot
With the contact side of the SmartMedia card facing
downwards, insert the card into the card slot. Carefully push
the card into the slot as far as it will go.
The WK-3500 comes with a built-in disk drive, which
provides you with the capabilities described below.
• You can save song memory and synthesizer data on a floppy
diskette for long-term storage. When you need the data
again, simply insert the diskette into the disk drive and
load it.
• You can play back SMF (standard MIDI file) data created
on a personal computer and saved to diskette.
Floppy Diskette Precautions
IMPORTANT!
To remove a SmartMedia card from the slot
After making sure that the data access lamp is not lit and the
message “Pls Wait” is not on the display, carefully pull the
card from the slot.*
* Never remove the SmartMedia card from the card slot or
turn off the keyboard card while any of the following
conditions exists.
• While the keyboard is in the SMF Player Mode and there
is a pointer next to CARD on the display
• While the data access lamp is lit and the message “Pls
Wait” is on the display, indicating that a card access
operation is being performed
• Avoid the following locations when storing and using
diskettes. Any of the conditions noted below can cause
data stored on the diskette to become corrupted.
• Near TVs, on top of audio equipment, or in any area
exposed to magnetism. Take special care to keep
diskettes away from any source of magnetism.
• Areas exposed to direct sunlight, or subject to high
humidity or temperature extremes.
• Failure to observe any of the following precautions can
cause data stored on the diskette to become corrupted.
• Never try to take a diskette apart.
• Never open the shutter of the diskette or touch the
film inside with your fingers.
• Never bend a diskette or otherwise subject it to rough
handling.
• Affix labels in the spaces provided only, and do not
affix labels on top of previous ones.
IMPORTANT!
• Never remove the SmartMedia card from the card slot
or turn off the keyboard while card data is being accessed
by a save, read, or delete operation. Doing so can corrupt
the data on the SmartMedia card or even damage the
card slot.
• Do not eject the diskette from the drive while the access
lamp is lit or flashing or turn off keyboard power with a
diskette in the drive. Doing either can cause data on the
diskette to become corrupted and can even cause
malfunction of the disk drive.
• Never insert any foreign objects into the disk drive. Doing
so can cause it to malfunction.
• The disk drive uses a magnetic head. A dirty head cannot
read data from a diskette properly and can corrupt
existing data on the diskette. To avoid this, be sure to
use a commercially available head cleaning diskette to
periodically clean the head.
E-94
WK3100_e_89-105.p65
735A-E-096A
94
04.3.26, 0:11 PM
Saving Data
• Do not use a computer, another electronic musical
instrument, or any other device to change a file name or
file contents created with this keyboard. Doing so can
make the data unusable by this keyboard and even
cause malfunction of the keyboard.
Note that CASIO COMPUTER CO., LTD. shall not be held
liable for any loss to you or any third party due to
corruption or accidental erasure of data on a diskette.
Write Protection
IMPORTANT!
• You can write protect a diskette so data on it cannot be
deleted and no new data can be stored on the diskette.
Also, a write protected diskette cannot be formatted. You
can read data from a diskette regardless of whether or
not it is write protected.
Write protect (hole open)
Write enabled
(hole blocked with tab)
Data save, data delete,
disk formatting are all
enabled.
About Floppy Diskettes
This section contains important information about handling
diskettes. Be sure to read it before going any further.
Diskette Types
The WK-3500 supports use of both 3.5’ 2HD (1.44MB
formatted) and 2DD (720KB formatted) diskettes. Use of other
disk sizes and capacities is not supported.
Diskette Type Indicators
2HD ...... A 2HD diskette is marked with the letters “HD” in
the upper right corner of the front side. Also, there
is a square hole in the lower right corner.
2DD ....... This type of diskette does not have a hole in the
lower right corner.
HD
Hole
open
Write protect tab
• When the write protect hole is open as shown in the
illustration, you can read the contents of the diskette,
but you cannot write data to or delete data from the
diskette. After saving important data to a diskette, be
sure to open its write protect hole to protect the data
against accidental changes or deletion.
• The diskette that comes with the keyboard contains
sample data and programs. It is write protected to avoid
accidental erasure or formatting. Make sure you handle
this diskette carefully to avoid damaging or erasing its
data.
E-95
735A-E-097A
WK3100_e_89-105.p65
95
04.3.26, 0:11 PM
Saving Data
CURSOR
Eject button
●WK-3500
DISK/CARD
●WK-3100/WK-3000
[+]/[–]
Inserting and Ejecting a Diskette
The following describes how to insert a diskette into the disk
drive and how to eject it.
To insert a diskette into the floppy disk drive
1
With the label area of the diskette facing up, insert
the diskette shutter first into the disk drive, as shown
in the illustration.
CARD
Using External Storage Media
This section explains how to use SmartMedia cards and
floppy diskettes (WK-3500 only) for data storage. In this
manual, SmartMedia cards and floppy diskettes are
collectively referred to as “external storage media”.
NOTE
• Layer, split, and Auto Harmonize are automatically turned
off while external storage is being used. Tone and rhythm
selection, and rhythm playback are also all disabled.
Basic SmartMedia Card Operation
1 Insert the SmartMedia card into the card slot.
2 Enter the Card Mode.
2
* WK-3500
Press the DISK/CARD button twice.
• This causes a pointer to appear next to the DISK/
CARD on the display, and also displays “Card” in the
display’s text area.
Slide the diskette into the drive as far as it will go,
until it clicks into place.
* WK-3100/WK-3000
Press the CARD button.
• This causes a pointer to appear next to the CARD on
the display, and also displays “Card” in the display’s
text area.
To eject a diskette from the floppy disk drive
IMPORTANT!
• Before ejecting a diskette, always check to make sure
that the access lamp is not lit or flashing. A lit or flashing
access lamp means that the keyboard is performing a
data read or write operation. Ejecting a diskette while it
is being accessed can cause its data to become
corrupted.
1
3
Press the [왔] CURSOR button to display the Card
Mode menu.
Press the Eject button.
• This causes the diskette to be partially ejected from
the disk drive.
2
Remove the diskette from the drive by hand.
E-96
WK3100_e_89-105.p65
735A-E-098C
96
04.3.26, 0:11 PM
Saving Data
4 Use the [왗] and [왘] CURSOR buttons to display
A
Load
[왘]
[왗]
Sa v e
[왘]
[왗]
R e n ame
[왘]
[왗]
De l e t e
[왗]
[왘]
F o r ma t
B
• See the pages referenced below for details about using
each of the above menu operations.
Loading a file (Crd Load):
page E-99
Saving a file (Crd Save):
page E-98
Renaming a file (Crd Rename):
page E-100
Deleting a file (Crd Delete):
page E-101
Formatting a SmartMedia card (Crd Format): page E-102
5
Press the [왔] CURSOR button to advance to the
file type selection screen.
6 Use the [왗] and [왘] CURSOR buttons to select the
file type.
name selection screen.
8 Use the [왗] and [왘] CURSOR buttons or [+] and
[–] buttons to select the file name.
• Pressing the EXIT or [왖] CURSOR button at this time
will return you to the file type selection screen.
After you are finished performing the SmartMedia
card operation you want, press the DISK/CARD
button (CARD button on the WK-3100/WK-3000)
to exit the Card Mode.
• Exiting the Card Mode causes the pointer next to the
display’s DISK/CARD pointer (CARD pointer on the
WK-3100/WK-3000) to disappear.
Basic Floppy Diskette Operation
(WK-3500 Only)
1
2
• Pressing the EXIT or [왔] CURSOR button at this time
will return you to the Card Mode menu.
7 Press the [왔] CURSOR button to display the file
Press the [왔] CURSOR button to load the file.
• This will display a confirmation message asking
whether you really want to load the data. If you
already have data in the user area, the message will
ask if you want to overwrite the existing data with
the loaded data.
• Press the YES button to load the data. This will cause
the message “Pls Wait” to appear on the display to
indicate that a card access operation is being
performed. Never try to perform any other operation
on the keyboard while the card is being accessed. The
message “Complete” will appear on the display after
data loading is complete. After a few seconds, the
message will be replaced by the file name selection
screen.
• If you do not want to continue with data loading, press
the EXIT button or the NO button in response to the
above confirmation message. This will return you to
the user area selection screen in step 9.
the screen for the type of operation you want to
perform.
Insert a floppy diskette into the keyboard’s floppy
disk drive.
Press the DISK/CARD button.
• This causes a pointer to appear next to the DISK/
CARD on the display, and also displays “Disk” in the
display’s text area.
3
Perform the same operations as those starting from
step 3 of under “Basic SmartMedia Card Operation”
on page E-96.
• Note that Disk Mode operations are indicated on the
display by the prefix “Fd” in place of the “Crd” prefix
of the Card Mode operations.
9 Press the [왔] CURSOR button to advance to the
user area selection screen for file loading.
0 Use the [왗] and [왘] CURSOR buttons or [+] and
[–] buttons to select the user area.
• Pressing the EXIT or [왖] CURSOR button at this time
will return you to the file name selection menu.
E-97
735A-E-099C
WK3100_e_89-105.p65
97
04.3.26, 0:11 PM
Saving Data
CURSOR
●WK-3500
DISK/CARD
●WK-3100/WK-3000
[+]/[–]
YES/NO
CARD
To save a file to external storage media
Saving Files
You can use the procedures in this section to save Song
Memory, Synthesizer, and other data you create to external
storage media for later loading when you need it. See
“Savable File Types” on page E-92 for information about the
type of data you can save.
1
• SmartMedia Card:
On the WK-3500 press the DISK/CARD button twice. On
the WK-3100/WK-3000, press the CARD button once.
• This causes a pointer to appear next to the DISK/
CARD or CARD on the display, and also displays
“Card” in the display’s text area.
• Floppy Diskette (WK-3500 Only):
Press the DISK/CARD button.
• This causes a pointer to appear next to the DISK/
CARD on the display, and also displays “Disk” in
the display’s text area.
PREPARATION
• SmartMedia Card
Insert a properly formatted SmartMedia card into the
keyboard’s card slot. Make sure that the sticker is
removed from the card’s write area, which enables
writing.
• Floppy Diskette (WK-3500 Only)
Insert a properly formatted floppy diskette into the
keyboard’s floppy disk drive. Make sure that the
diskette’s write protect hole is closed, which enables
writing.
2
3
NOTE
• Depending on the type and the amount of data involved,
a SmartMedia card or floppy diskette (WK-3500 only)
data save or load operation can take anywhere from a
few minutes to more than 10 minutes to complete. The
message “Pls Wait” will remain on the display to indicate
that a data save or load operation is being performed.
4
5
6
IMPORTANT!
• Never try to perform any operation while “Pls Wait” is
displayed. Performing any operation can cause Flash
memory or SmartMedia card or floppy diskette data to
be deleted, and damage the keyboard’s memory and
cause it to malfunction.
What you should do first depends on the type of
external storage media you are using.
7
Press the [왔] CURSOR button to display the Card
Mode (or Disk Mode) menu.
Use the [왗] and [왘] CURSOR buttons to display
the “Save” screen.
Press the [왔] CURSOR button to advance to the
file type selection screen.
Use the [왗] and [왘] CURSOR buttons to select the
file type.
Press the [왔] CURSOR button to advance to the
user area selection screen.
Use the [왗] and [왘] CURSOR buttons or [+] and
[–] buttons to select the user area you want.
• The numeric area of the display will show the user area
number, while the text area will show the user area name.
• Pressing the EXIT or [왖] CURSOR button at this time
will return you to the file type selection screen.
8
Press the [왔] CURSOR button to advance to the
file name input screen.
• Use the [+] and [–] buttons to scroll through letters at
the current cursor location. See the page E-103 for
information about inputting text.
• Use the [왗] and [왘] CURSOR buttons to move the
cursor left and right.
E-98
WK3100_e_89-105.p65
735A-E-100C
98
04.3.26, 0:12 PM
Saving Data
9
After inputting the file name, press the [왔] CURSOR
button.
• If you are saving song data, the file type selection
screen appears next. Use the [왗] and [왘] CURSOR
buttons to select “SMF” or “SONG”. After selecting a
file type, press the [왔] CURSOR button.
• This will display a confirmation message asking
whether you really want to save the data. If you
already have data in the user area, the message will
ask if you want to overwrite the existing data with
the loaded data.
0
Press the YES button to save the data. This will cause
the message “Pls Wait” to appear on the display to
indicate that a card access operation is being
performed. Never try to perform any other operation
on the keyboard while the card is being accessed. The
message “Complete” will appear on the display after
data save is complete. After a few seconds, the message
will be replaced by the file name selection screen.
• If you do not want to continue with data save, press
the EXIT button or the NO button in response to the
above confirmation message. This will return you to
the user area selection screen in step 7.
A
After you are finished performing the save
operation, press the DISK/CARD button (CARD
button on the WK-3100/WK-3000) to exit the Card
Mode.
PREPARATION
• SmartMedia Card
• Insert the SmartMedia card that contains the data you
want to load into the keyboard’s card slot.
• Floppy Diskette (WK-3500 Only)
• Insert the floppy diskette that contains the data you
want to load into the keyboard’s floppy disk drive.
NOTE
• Depending on the type and the amount of data involved,
a SmartMedia card or floppy diskette (WK-3500 only)
data save or load operation can take anywhere from a
few minutes to more than 10 minutes to complete. The
message “Pls Wait” will remain on the display to indicate
that a data save or load operation is being performed.
IMPORTANT!
• Never try to perform any operation while “Pls Wait” is
displayed. Performing any operation can cause Flash
memory or SmartMedia card or floppy diskette data to
be deleted, and damage the keyboard’s memory and
cause it to malfunction.
To recall file data from external storage media
1
• SmartMedia Card
On the WK-3500 press the DISK/CARD button twice. On
the WK-3100/WK-3000, press the CARD button once.
• This causes a pointer to appear next to the DISK/
CARD or CARD on the display, and also displays
“Card” in the display’s text area.
• Floppy Diskette (WK-3500 Only)
Press the DISK/CARD button.
• This causes a pointer to appear next to the DISK/
CARD on the display, and also displays “Disk” in
the display’s text area.
Loading a File
Use the procedures in this section when you want to load data
from external storage media into the keyboard’s user area.
IMPORTANT!
• Note the following important points whenever using the SMF
Player Mode to play back data saved with the above procedure.
* SmartMedia Card
To perform the procedure below, you must have a
SmartMedia card to which SMF data has been copied from
a computer. Insert a SmartMedia card that you have
formatted on the keyboard into the card slot of your
computer, and copy the SMF data you want to load into
the directory named “CASIO_MD”. Note that you will not
be able to load the data if it is not located inside the
“CASIO_MD” directory. If you create a sub-directory inside
of the “CASIO_MD” directory, the keyboard will not be
able to load any data inside the sub-directory.
* Floppy Diskette (WK-3500 only)
This keyboard is able to see only files that are in the top
(root) directory of the floppy diskette. It will not be able to
see any files that are located in a subdirectory.
What you should do first depends on the type of
external storage media you are using.
2
3
4
5
6
7
Press the [왔] CURSOR button to display the Card
Mode (or Disk Mode) menu.
Use the [왗] and [왘] CURSOR buttons to display
the “Load” screen.
Press the [왔] CURSOR button to advance to the
file type selection screen.
Use the [왗] and [왘] CURSOR buttons to select the
type file you want to load.
Press the [왔] CURSOR button to display the file
name selection screen.
Use the [왗] and [왘] CURSOR buttons or [+] and [–]
buttons to select the name of the file you want to load.
E-99
735A-E-101C
WK3100_e_89-105.p65
99
04.3.26, 0:12 PM
Saving Data
CURSOR
●WK-3500
DISK/CARD
●WK-3100/WK-3000
[+]/[–]
YES/NO
CARD
8
Press the [왔] CURSOR button to advance to the
user area selection screen.
• The user area selection screen will not appear if the
file you selected in step 5 is a package file or “All
Data” file. In this case, skip step 9 and go directly to
step 10.
9
Use the [왗] and [왘] CURSOR buttons or [+] and
[–] buttons to select the user area to which you
want to import the loaded file data.
• The numeric area of the display will show the user
area number, while the text area will show the user
area name.
• Pressing the EXIT or [왖] CURSOR button at this time
will return you to the file type selection screen.
0
After selecting the user area, press the [왔] CURSOR
button.
• This will display a confirmation message asking
whether you really want to load the data. If you
already have data in the user area, the message will
ask if you want to overwrite the existing data with
the loaded data.
A
You can use the procedures in this section to change the name
of a file that you previously saved to external storage media.
PREPARATION
• SmartMedia Card
• Insert the SmartMedia card that contains the file you
want to rename into the keyboard’s card slot. Make
sure that the sticker is removed from the card’s write
area, which enables writing.
• Floppy Diskette (WK-3500 Only)
• Insert the floppy diskette that contains the file you want
to rename into the keyboard’s floppy disk drive. Make
sure that the diskette’s write protect hole is closed,
which enables writing.
To rename a file saved to external storage media
1
After you are finished performing the load
operation, press the DISK/CARD button (CARD
button on the WK-3100/WK-3000) to exit the Card
Mode.
What you should do first depends on the type of
external storage media you are using.
• SmartMedia Card
On the WK-3500 press the DISK/CARD button twice.
On the WK-3100/WK-3000, press the CARD button
once.
• This causes a pointer to appear next to the DISK/
CARD or CARD on the display, and also displays
“Card” in the display’s text area.
• Floppy Diskette (WK-3500 Only)
Press the DISK/CARD button.
• This causes a pointer to appear next to the DISK/
CARD on the display, and also displays “Disk” in
the display’s text area.
Press the YES button to recall the data.
• This will cause the message “Pls Wait” to appear on
the display to indicate that a card access operation is
being performed. Never try to perform any other
operation on the keyboard while the card is being
accessed. The message “Complete” will appear on the
display after data loading is complete. After a few
seconds, the message will be replaced by the file name
selection screen.
• If you do not want to continue with data loading, press
the EXIT button or the NO button in response to the
above confirmation message. This will return you to
the user area selection screen in step 9.
B
Renaming a File
2
3
4
Press the [왔] CURSOR button to display the Card
Mode (or Disk Mode) menu.
Use the [왗] and [왘] CURSOR buttons to display
the “Rename” screen.
Press the [왔] CURSOR button to advance to the
file type selection screen.
E-100
WK3100_e_89-105.p65
735A-E-102C
100
04.3.26, 0:12 PM
Saving Data
5
6
7
8
Use the [왗] and [왘] CURSOR buttons to select the
type of the file you want to rename.
Press the [왔] CURSOR button to display the file
name selection screen.
Use the [왗] and [왘] CURSOR buttons or [+] and
[–] buttons to select the name of the file you want
to rename.
Press the [왔] CURSOR button to advance to the
file name input screen.
• Use the [+] and [–] buttons to scroll through letters at
the current cursor location. See the page E-103 for
information about inputting text.
• Use the [왗] and [왘] CURSOR buttons to move the
cursor left and right.
9
After inputting the file name, press the [왔] CURSOR
button.
• This will display a confirmation message asking
whether you really want to change the name.
0
Press the YES button to change the file name.
• This will cause the message “Pls Wait” to appear on
the display to indicate that a card access operation is
being performed. Never try to perform any other
operation on the keyboard while the card is being
accessed. The message “Complete” will appear on the
display after renaming is complete. After a few
seconds, the message will be replaced by the file name
selection screen.
• If you do not want to continue with file renaming,
press the EXIT button or the NO button in response
to the above confirmation message. This will return
you to the user area selection screen in step 5.
A
After you are finished performing the rename
operation, press the DISK/CARD button (CARD
button on the WK-3100/WK-3000) to exit the Card
Mode.
Deleting a File
You can perform the procedure in this section to delete a file
from external storage media.
IMPORTANT!
• Note that the file delete operation cannot be undone.
Make sure that you no longer need data before you
delete it.
PREPARATION
• SmartMedia Card
• Insert the SmartMedia card that contains the file you
want to delete into the keyboard’s card slot. Make sure
that the sticker is removed from the card’s write area,
which enables writing.
• Floppy Diskette (WK-3500 Only)
• Insert the floppy diskette that contains the file you want
to delete into the keyboard’s floppy disk drive. Make
sure that the diskette’s write protect hole is closed,
which enables writing.
To delete a file from external storage media
1
What you should do first depends on the type of
external storage media you are using.
• SmartMedia Card
On the WK-3500 press the DISK/CARD button twice.
On the WK-3100/WK-3000, press the CARD button
once.
• This causes a pointer to appear next to the DISK/
CARD or CARD on the display, and also displays
“Card” in the display’s text area.
• Floppy Diskette (WK-3500 Only)
Press the DISK/CARD button.
• This causes a pointer to appear next to the DISK/
CARD on the display, and also displays “Disk” in
the display’s text area.
2
3
4
5
6
Press the [왔] CURSOR button to display the Card
Mode (or Disk Mode) menu.
Use the [왗] and [왘] CURSOR buttons to display
the “Delete” screen.
Press the [왔] CURSOR button to advance to the
file type selection screen.
Use the [왗] and [왘] CURSOR buttons to select the
type of the file you want to delete.
Press the [왔] CURSOR button to display the file
name selection screen.
E-101
735A-E-103C
WK3100_e_89-105.p65
101
04.3.26, 0:12 PM
Saving Data
CURSOR
●WK-3500
DISK/CARD
●WK-3100/WK-3000
[+]/[–]
YES/NO
CARD
7
8
Use the [왗] and [왘] CURSOR buttons or [+] and
[–] buttons to select the name of the file you want
to delete.
After selecting the file, press the [왔] CURSOR
button.
• This will display a confirmation message asking
whether you really want to delete the file.
9
Press the YES button to delete the file.
• This will cause the message “Pls Wait” to appear on
the display to indicate that a card access operation is
being performed. Never try to perform any other
operation on the keyboard while the card is being
accessed. The message “Complete” will appear on the
display after file deletion is complete. After a few
seconds, the message will be replaced by the file name
selection screen.
• If you do not want to continue with file deletion, press
the EXIT button or the NO button in response to the
above confirmation message. This will return you to
the file name selection screen.
0
After you are finished performing the delete
operation, press the DISK/CARD button (CARD
button on the WK-3100/WK-3000) to exit the Card
Mode.
Formatting External Storage Media
Use the procedures in this section to format external storage
media before using it for the first time, or when you want to
delete all of the contents on a SmartMedia card or floppy
diskette.
IMPORTANT!
• Note that formatting a card or diskette that already
contains data causes all of that data to be deleted. Data
deleted by the format operation cannot be recovered.
Before performing the procedure below, check to make
sure that the media does not contain any data you might
need.
PREPARATION
• SmartMedia Card
• Insert the SmartMedia card you want to format into
the keyboard’s card slot. Make sure that the sticker is
removed from the card’s write area, which enables
writing.
• Floppy Diskette (WK-3500 Only)
• Insert the floppy diskette you want to format into the
keyboard’s floppy disk drive. Make sure that the
diskette’s write protect hole is closed, which enables
writing.
E-102
WK3100_e_89-105.p65
735A-E-104C
102
04.3.26, 0:12 PM
Saving Data
To format external storage media
Inputting Characters
1
The following describes the types of characters you can input
when saving data to the user area and external storage media.
What you should do first depends on the type of
storage media you are using.
• SmartMedia Card
On the WK-3500 press the DISK/CARD button twice.
On the WK-3100/WK-3000, press the CARD button
once.
• This causes a pointer to appear next to the DISK/
CARD or CARD on the display, and also displays
“Card” in the display’s text area.
• Floppy Diskette (WK-3500 Only)
Press the DISK/CARD button.
• This causes a pointer to appear next to the DISK/
CARD on the display, and also displays “Disk” in
the display’s text area.
2
3
4
Press the [왔] CURSOR button to display the Card
Mode (or Disk Mode) menu.
Use the [왗] and [왘] CURSOR buttons to display
the “Format” screen.
Press the [왔] CURSOR button.
• WK-3500 Users
If you are formatting a floppy diskette, a screen will
appear here for specification of the floppy diskette
density. Use the [왗] and [왘] CURSOR buttons to select
either “2DD” or “2HD”, and then press the [왔]
CURSOR button.
• This will display a confirmation message asking
whether you really want to format the media.
5
User Area Data
External Storage Media Data
You can input the same characters as those that are allowed
for MS-DOS file names.
Press the YES button to start formatting.
• This will cause the message “Pls Wait” to appear on
the display to indicate that a card access operation is
being performed. Never try to perform any other
operation on the keyboard while the card is being
accessed. The message “Complete” will appear on the
display after media formatting is complete. After a
few seconds, the message will be replaced by the file
name selection screen.
• If you do not want to continue with formatting, press
the EXIT button or the NO button in response to the
above confirmation message. This will return you to
the mode menu.
6
After you are finished performing the format
operation, press the DISK/CARD button (CARD
button on the WK-3100/WK-3000) to exit the Card
Mode.
E-103
735A-E-105C
WK3100_e_89-105.p65
103
04.3.26, 0:12 PM
Saving Data
SmartMedia Card Error Messages
Display Message
Cause
Action
Err Card R/W
There is something wrong with the card.
Use a different card.
Err CardFull
The card is full.
1. Use a different card.
2. Delete files you no longer need from the
card (page E-101).
Err No Card
1. The card is not set correctly in the card slot.
1. Remove the card and reinsert it correctly
(page E-94).
2. Insert a card into the card slot. Never remove
a card from the card slot while a card access
operation is in progress.
2. There is no card in the card slot or the card
was removed part way through a card
operation.
1. A file with the same name as the one you
are trying to use already exists.
2. You are trying to use a file name that is not
allowed by MS-DOS.
1. Use a different name (page E-100).
Err ReadOnly
Attempt to save a file using the same name as
an existing file that is read only.
Save the new file to a different card or use
another name.
Err Format
1. The format of the card is not compatible
with this keyboard.
2. The card is not formatted.
3. The card is damaged.
1. Change to a card that has the proper format.
................................................................ E-102
2. Format the card. ................................... E-102
3. Use a different card.
Err Mem Full
Keyboard memory became full while
importing data from card.
1. Delete data you no longer need from the
user area that corresponds to the file you
are trying to store.
2. If you have song data stored in Song
Memory (SG0 to 4), delete the song data
you no longer need. ............................... E-72
Err Not SMF0
The file you are reading is not an SMF 0 format
file.
Use SMF 0 format files only.
Err No File
The keyboard cannot find any file it can read
on the card.
Use a card that contains data stored by this
keyboard or compatible data from another
device.
Err Protect
The card is write protected.
1. Use a different card.
2. Remove the card’s write protect sticker to
enable data storage. ............................... E-93
Err Convert
There is not enough memory to save data
produced by converting song data from SONG
format to SMF format.
Delete SMFs you no longer need from your
SMF data (page E-80).
Err WrongDat
The data on the card is corrupted.
Use other data or another card.
Err Name
2. Name files using the allowable characters
(page E-103).
E-104
WK3100_e_89-105.p65
735A-E-106B
104
04.3.26, 0:12 PM
Saving Data
Disk Drive Error Messages (WK-3500 Only)
Display Message
Cause
Action
Err ReadOnly
Attempt to save a file using the same name as
an existing file that is read only.
Save the new file to a different diskette or use
another name.
Err Format
1. The format of the diskette is not compatible
with this keyboard.
2. The diskette is not formatted.
3. The diskette is damaged.
1. Change to a diskette that has the proper
format. .................................................... E-102
2. Format the diskette. ............................. E-102
3. Use a different diskette.
Err Disk R/W
The diskette is damaged.
Use a different diskette.
Err DiskFull
The diskette is full.
1. Use a different diskette.
2. Delete any files you no longer need in order
to make room for the data you want to save.
................................................................ E-101
Err Mem Full
Keyboard memory became full while
importing data from diskette.
1. Delete data you no longer need from the
user area that corresponds to the file you
are trying to store.
2. If you have song data stored in Song
Memory (SG0 to 4), delete the song data
you no longer need. ............................... E-72
Err Not SMF0
The file you are reading is not an SMF 0 format
file.
Use SMF 0 format files only
Err No Disk
1. The diskette is not loaded in the drive
correctly.
2. No diskette is loaded in the drive.
1. Eject the diskette from the drive and reload
it. ............................................................... E-94
2. Load a diskette into the drive.
Err No File
The keyboard cannot find any file it can read
on the diskette.
Use a diskette that contains data stored by this
keyboard or compatible data from another
device.
Err Protect
The diskette is write protected.
1. Use a different diskette.
2. Close the diskette’s write protect hole to
enable data storage. ............................... E-95
Err Convert
There is not enough memory to save data
produced by converting song data from SONG
format to SMF format.
Delete SMFs you no longer need from your
SMF data (page E-80).
Err WrongDat
The file you are reading is a wrong format file.
The data on the diskette is corrupted.
Use other data or another diskette.
Err Name
A file with the same name as the one you are
trying to use already exists on the floppy
diskette.
Use a different name (page E-100).
E-105
735A-E-107A
WK3100_e_89-105.p65
105
04.3.26, 0:12 PM
Troubleshooting
Problem
Possible Cause
No keyboard sound
1. Power supply problem.
2. Power is not turned on.
3. Volume setting is too low.
4. Playing in the accompaniment
keyboard area while the MODE
button setting is CASIO CHORD
or FINGERED.
5. Local Control is off.
6. Mixer channel 1 is turned off.
7. Mixer channel 1 volume setting
is too low.
8. The DSP volume parameter is set
too low.
9. The Expression value of the file
data played back on the SMF
player is too low.
Any of the following symptoms
while using battery power.
Low battery power
Action
See page
1. Correctly attach the AC adaptor,
make sure that batteries poles (+/
–) are facing correctly, and check
to make sure that batteries are
not dead.
2. Press the POWER button to turn
on power.
3. Use the VOLUME knob to
increase volume.
4. None of the accompaniment
mode indicators are lit, which
means Auto Accompaniment is
turned off.
5. Turn on Local Control.
6. Use the Mixer to turn channel 1
on.
7. Use the Mixer to raise the volume
setting for channel 1.
8. Increase the DSP parameter
value.
9. Exit then re-enter the SMF Player
Mode, or change the SMF Player
play-along part.
E-16, 17
Replace the batteries with a set of
new ones or use the AC adaptor.
E-16, 17
E-22
E-22
E-38
E-82
E-47
E-48
E-50
E-84
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Dim power indicator
Instrument does not turn on.
Display that is flickering, dim, or difficult to read
Abnormally low speaker/headphone volume
Distortion of sound output
Occasional interruption of sound when playing at high volumes
Sudden power failure when playing at high volumes
Flickering or dimming of the display when playing at high volume
Continued sound output even after you release a key
A tone that is totally different from the one that is selected.
Abnormal rhythm pattern and demo tune play
Abnormally low microphone volume (WK-3100 only)
Distortion of microphone input (WK-3100 only)
Dim power supply indicator when a microphone is used (WK-3100 only)
Sudden power failure when using the microphone (WK-3100 only)
Loss of power, sound distortion, or low volume when playing from a connected computer or
MIDI device
• Sudden power failure while reading from or writing to a diskette (WK-3500 only)
Auto Accompaniment does not
sound.
1. Accompaniment volume is set to
000.
2. Auto Accompaniment part
Channels 6 through 10 are turned
off.
3. Auto Accompaniment part
Channels 6 through 10 volume
setting is too low.
1. Use the ACCOMP VOLUME
button to increase the volume.
2. Use the Mixer to turn the channels
on.
E-46
3. Use the Mixer to raise the volume
setting for the applicable channel.
E-48
E-106
WK3100_e_106-112.p65
E-47
735A-E-108C
106
04.3.26, 0:12 PM
Troubleshooting
Problem
Possible Cause
Action
See page
Sound output does not change
when key pressure is varied.
Touch response is turned off.
Press
the
TRANSPOSE/
FUNCTION button to turn it on.
E-78
Playing the keyboard sounds
two tones.
Layer is turned on.
Press the LAYER button to turn off
layering.
E-74
Different tones sound when
keys in different keyboard
ranges are pressed.
Split is turned on.
Press the SPLIT button to turn off
split.
E-75
The key or tuning does not
match when playing along with
another MIDI machine.
1. The tuning or transpose
parameter is set to a value other
than 00.
2. Mixer coarse tune, fine tune, and/
or octave shift settings are values
other than 00.
1. Change the transpose or tuning
parameter value to 00.
E-77, 78
2. Use the Mixer to change the
coarse tune, fine tune, and/or
octave shift settings to 00.
E-49
Parts suddenly drop out during
song memory playback.
The number of tones being played
at the same time exceeds the
keyboard’s limitation.
Use the Mixer to turn unneeded
channels off and decrease the
number of parts being played.
E-47
Some parts do not play at all
during song memory playback.
1. Channels are turned off.
1. Use the Mixer to turn channels
on.
2. Use the Mixer to check the
volume setting.
E-47
1. Use the Mixer to turn on
Channels 2 through 4.
E-47
2. Use the Mixer to raise the volume
setting of Channels 2 through 4.
E-48
3. The LAYER and SPLIT buttons
are disabled during recording
and record standby.
4. Turn off the SMF Player Mode.
LAYER and SPLIT are not
available while the SMF Player
Mode is in use.
E-74, 75
2. Volume setting is too low.
Nothing happens when the
LAYER or SPLIT button is
pressed.
1. One or more of the melody
channels (2 through 4) is turned
off.
2. The volume setting of one or
more of the melody channels (2
through 4) is too low.
3. The keyboard is in record
standby.
4. The SMF Player Mode is currently
being use.
E-48
E-84
No sound is produced when
playing MIDI data from a
computer.
1. MIDI cables are not connected
properly.
2. Channel is turned off, or volume
setting is too low.
1. Connect MIDI cables properly.
E-89
2. Use the Mixer to turn the channel
on, or raise the volume setting.
E-46, 47
Playing on the keyboard
produces an unnatural sound
when connected to a computer.
The computer’s MIDI Thru function
is turned on.
Turn off the MIDI Thru function on
the computer or turn off Local
Control on the keyboard.
E-82
Cannot
record
chord
accompaniment data on a
computer.
Accomp/Song MIDI Out is turned
off.
Turn on Accomp/Song MIDI Out.
E-82
E-107
735A-E-109A
WK3100_e_106-112.p65
107
04.3.26, 0:12 PM
Troubleshooting
Problem
Possible Cause
Action
The keyboard starts up
abnormally when it is turned
on.
Flash memory is corrupted. There
is something wrong with the card.
1. Remove the batteries from the
keyboard and disconnect the AC
adaptor and press the POWER
button.
2. Reload the batteries and/or
reconnect the AC adaptor, and
then press the POWER button
again to turn on power.
3. Use
the
TRANSPOSE/
FUNCTION button to perform
the system reset operation.
• If this does not solve the
problem, contact your nearest
authorized CASIO Service
Provider to request repair.
E-83
A downloaded tone with
waveform contains noise or
keyboard operations become
abnormal when user data is
selected.
Someone may have turned off the
keyboard while data was being
stored in Flash memory or
something else has caused Flash
memory contents to become
corrupted for some reason.
Use the TRANSPOSE/FUNCTION
button to perform the system reset
operation. If this does not correct
the problem, contact your nearest
authorized CASIO Service Provider
to request maintenance.
E-83
Cannot save data to a card.
1. The card is write-protected.
1. Remove the write-protect sticker
from the card.
2. Correctly insert the card into the
card slot.
3. Use a different card or delete files
you no longer need from the card
you are using.
4. Use only a card of the voltage
and capacity specified for this
keyboard.
5. Use a different card.
E-93
1. Correctly insert the card into the
card slot.
2. Delete rhythm, SMF, or tone with
wave data currently in the
keyboard’s Flash memory to
make room from the imported
data.
3. Use only a card of the voltage
and capacity specified for this
keyboard.
4. Use a different card.
E-94
1. Use of a microphone that is
different from the type that is
recommended.
2. Use of the microphone in the
vicinity of fluorescent lighting.
1. Use a full metal shielded Cannon
type microphone.
E-21
2. Move the microphone away from
source of the static.
E-21
1. Microphone volume setting is too
low.
2. Microphone’s on/off switch is set
to OFF.
1. Increase the microphone volume
setting.
2. Change the microphone’s on/off
switch setting to ON.
E-21
2. The card is not inserted correctly
into the card slot.
3. There is not enough space left on
the card.
4. You are trying to use a card whose
voltage or capacity is not
supported by this keyboard.
5. The card is damaged.
Cannot recall data from a card.
1. The card is not inserted correctly
into the card slot.
2. There is not enough space
available in the area into which
you are trying to import the data.
3. You are trying to use a card whose
voltage or capacity is not
supported by this keyboard.
4. The card is damaged.
Static noise when a microphone
is connected.
(WK-3100 only)
No microphone sound
(WK-3100 only)
E-108
WK3100_e_106-112.p65
See page
E-94
E-101
E-93
E-83
E-93
E-21
735A-E-110C
108
04.3.26, 0:12 PM
Specifications
Model:
WK-3500/WK-3100/WK-3000
Keyboard:
76 standard-size keys, 6 1/4 octaves with touch response (OFF/1/2/3)
Tones:
300 Advanced Tones + 200 Preset Tones + 16 Drum Sets + 100 standard user
tones + 20 user tones with waves* + 4 drum sets with waves* + 50 drawbar
organ tones + 100 user drawbar organ tones + 150 Drawbar Organ Tones (790
tones total); layer/split
Rhythm Instrument Tones:
61
Polyphony:
32 notes maximum (10 for certain tones)
Drawbar Organ Function
Drawbars:
9 (16’, 5 1/3’, 8’, 4’, 2 2/3’, 2’, 1 3/5’, 1 1/3’, 1’)
Percussion:
Second, Third
Click:
On, Off
DSP (200 types: internal, 100 user areas) + Reverb (16 types) + Chorus (16 types)
+ Equalizer (10 types, 4 bands)
Effects:
Auto Accompaniment
Rhythm Patterns:
156 (internal, 16 user areas*)
Tempo:
Variable (226 steps,
Chords:
3 fingering methods (CASIO CHORD, FINGERED, FULL RANGE CHORD)
Rhythm Controller:
START/STOP, INTRO/ENDING 1 and 2, VARIATION/FILL-IN 1 and 2,
SYNCHRO/FILL-IN NEXT
Accomp Volume:
0 to 127 (128 steps)
One-touch Presets:
Recalls settings for tone, tempo, layer on/off, and harmonize on/off in
accordance with rhythm.
Auto Harmonize:
10 types : Automatic addition of notes that harmonize with melody note in
accordance with specified Auto Accompaniment chords.
= 30 to 255)
Memory Function
Songs:
5
Recording Tracks:
6 (2 through 6 are melody tracks)
Recording Methods:
Real-time, step
Memory Capacity:
Approximately 10,000 notes (total for 5 songs)
Edit Function:
Equipped
3
Demo Tunes:
<WK-3500>
Tune Number
Name
Composer
Play Time
0
Garage Flava
Steave Turner
2:15
1
Breath of Air
Hage Software
2:19
2
Nora Park
TECH-NOTE INTERNATIONAL LTD.
2:06
<WK-3100/WK-3000>
Tune Number
Name
Composer
Play Time
0
Nora Park
TECH-NOTE INTERNATIONAL LTD.
2:06
1
Garage Flava
Steave Turner
2:15
2
Strut With Beauty
Edward Alstrom
1:52
E-109
735A-E-111C
WK3100_e_106-112.p65
109
04.3.26, 0:12 PM
Specifications
Synthesizer Function
Parameters:
Attack time; release time; resonance; cutoff frequency; vibrato type; vibrato
delay; vibrato depth; vibrato rate; octave shift; level; touch sense; reverb send;
chorus send; DSP line; DSP type; DSP parameter; 300 Advanced Tones + 200
Preset Tones + 16 Drum Sounds + 124 User Tones + 150 Drawbar Organ Tones
(790 tones total)
Registration Memory
Number of Setups:
32 (4 setups x 8 banks)
Memory Contents:
Tone, Rhythm, Tempo, Layer on/off, Split on/off, Split point, Harmonize on/
off, Mixer settings (Channels 1 to 10), Effect settings, Touch Response settings,
Assignable jack setting, Transpose, Tuning, Accompaniment volume setting,
Pitch bend range, Auto Harmonize type, MODE button setting, Synchro
standby state, Mixer Hold, DSP Hold, Synthesizer Mode parameters
Mixer Function
Channels:
16
Parameters:
Tone; part on/off; volume; pan pot; octave shift; coarse tune; fine tune; reverb
send; chorus send; DSP line; DSP level, DSP pan, DSP system reverb send, DSP
system chorus send
16 multi-timbre receive, GM Level 1 standard
MIDI:
Other Functions
Pitch Bend Range:
Adjustable (12 semitones upwards and downwards)
Modulation:
Equipped
Transpose:
49 steps (–24 semitones to +24 semitones)
Tuning:
Variable (A4 = approximately 440Hz ±100 cents)
LCD:
Adjustable contrast
Flash memory storage for up to 200 files*
SMF Player:
Supported Format:
SMF0
Flash Memory
Capacity:
2MB
Shared Area:
Approximately 1.5MB (waveform data, accompaniment data, SMF data)
Further storage of waveform, accompaniment, and SMF data becomes
impossible after the total of such data reaches approximately 1.5MB.
3.3V SmartMediaTM (8MB, 16MB, 32MB, 64MB, 128MB)
Card Slot
Functions:
Save and load of user tones, user songs, and registration data; playback of SMF;
card formatting; file delete; file rename
Floppy Disk Drive (WK-3500 only)
Type:
3.5" FDD
Formats:
2DD (720KB MS-DOS format)
2HD (1.44MB MS-DOS format)
Functions:
Save and load of user tones, user songs, and registration data; playback of SMF;
disk formatting; file delete; file rename
E-110
WK3100_e_106-112.p65
735A-E-112B
110
04.3.26, 0:12 PM
Specifications
Terminals
MIDI Terminals:
IN, OUT
Sustain/Assignable Terminal:
Standard jack (sustain, sostenuto, soft, rhythm start/stop)
•WK-3500
Headphones:
Stereo standard jack
Output Impedance : 200Ω
Output Voltage : 250mV (RMS) MAX
Line Out (R, L/MONO):
Standard jack x 2
Output Impedance : 3kΩ
Output Voltage : 1.5V (RMS) MAX
•WK-3100/WK-3000
Headphone/Output Terminal:
Stereo standard jack
Output Impedance: 200Ω
Output Voltage: 5.5V (RMS) MAX
Power Supply Terminal:
12V DC
Microphone In: (WK-3100 only)
Stereo standard jack (with microphone volume knob)
Input impedance: 1 kΩ
Input sensitivity: 10 mV
Dual power supply system
Power Supply:
Batteries:
6 D-size batteries
Battery Life:
Approximately 4 hours continuous operation on alkaline batteries
AC Adaptor:
AD-12
Auto Power Off:
Turns power off approximately six minutes after last key operation. Enabled
under battery power only, can be disabled manually.
Speaker Output:
6.1W + 6.1W
Power consumption:
12V
Dimensions:
122.3 x 42.3 x 16.0 cm (48 3/16 x 16 11/16 x 6 5/16 inch)
Weight:
WK-3500: Approximately 10.0 kg (22.0 lbs) (without batteries)
18W
WK-3100/WK-3000: Approximately 9.5 kg (20.9 lbs) (without batteries)
* The same memory area is used to store waveform data, accompaniment data, and SMF data.
E-111
735A-E-113C
WK3100_e_106-112.p65
111
04.3.26, 0:12 PM
Care of your Instrument
Avoid heat, humidity or direct sunlight.
Do not overexpose the instrument to direct sunlight, or place it near an air conditioner, or in any extremely hot place.
Do not use near a TV or radio.
This instrument can cause video or audio interference with TV and radio reception. If this happens, move the instrument away
from the TV or radio.
Do not use lacquer, thinner or similar chemicals for cleaning.
Clean the instrument with a soft cloth dampened in a weak solution of water and a neutral detergent. Soak the cloth in the
solution and squeeze until it is almost dry.
Avoid use in areas subjected to temperature extremes.
Extremely high or low temperature can cause figures on the LCD screen to become dim and difficult to read. This condition
should correct itself when the instrument is brought back to normal temperature.
NOTE
• You may notice lines in the finish of the case of this instrument. These lines are a result of the molding process used to shape
the plastic of the case. They are not cracks or breaks in the plastic, and are no cause for concern.
E-112
WK3100_e_106-112.p65
735A-E-114A
112
04.3.26, 0:12 PM
Appendix
Tone List
Advanced Tones
No.
Tone Group
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
PIANO
PIANO
PIANO
PIANO
PIANO
PIANO
PIANO
PIANO
PIANO
PIANO
PIANO
PIANO
PIANO
PIANO
PIANO
PIANO
PIANO
PIANO
PIANO
E.PIANO
E.PIANO
E.PIANO
E.PIANO
E.PIANO
E.PIANO
E.PIANO
E.PIANO
E.PIANO
E.PIANO
E.PIANO
E.PIANO
E.PIANO
E.PIANO
E.PIANO
E.PIANO
E.PIANO
CHROM.PERC
CHROM.PERC
CHROM.PERC
CHROM.PERC
CHROM.PERC
CHROM.PERC
CHROM.PERC
CHROM.PERC
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
Tone Name
STEREO GRAND PIANO
STEREO MELLOW PIANO
STEREO BRIGHT PIANO
GRAND PIANO
MELLOW PIANO
BRIGHT PIANO
GRAND PIANO WIDE
HARPSICHORD
ELEC. GRAND PIANO
SYNTH-STR PIANO
MODERN PIANO
STRINGS PIANO
VOICE PIANO
DANCE PIANO
MODERN E.G.PIANO
HONKY-TONK 1
1 OCTAVE PIANO
2 OCTAVE PIANO
COUPLED HARPSICHORD
ELEC. PIANO 1
MODERN EP 1
TREMOLO E.PIANO
60’S E.PIANO
MELLOW E.PIANO
SYNTH-STR. E.PIANO 2
CLAVI
SOFT E.PIANO
AUTO WAH E.PIANO
PHASER E.PIANO
GLASS E.PIANO
E.PIANO PAD
SYNTH-STR. E.PIANO 1
MODERN EP 2
STRINGS E.PIANO
RESONANCE CLAVI
PULSE CLAVI
TREMOLO VIBRAPHONE
MARIMBA
GLOCKENSPIEL
CELESTA
VIBRAPHONE
PHASER MARIMBA
DELAY GLOCKENSPIEL
DELAY CELESTA
ROTARY DRAWBAR
ROTARY PERC. ORGAN 1
70’S ORGAN
TREMOLO ORGAN
JAZZ DRAWBAR
ROCK ORGAN
ROTARY ELEC. ORGAN
ROTARY PERC. ORGAN 2
CHURCH ORGAN 1
Program
Change
0
0
1
0
0
1
0
6
2
0
1
1
0
1
2
3
3
3
6
4
5
4
4
4
5
7
5
4
4
4
4
4
5
5
7
7
11
12
9
8
11
12
9
8
16
17
17
16
17
18
16
17
19
Bank Select Maximum
MSB
Polyphony
51
52
50
48
50
48
49
51
48
54
51
52
53
53
50
48
51
50
49
48
48
55
51
52
52
48
50
56
57
50
53
54
49
53
50
49
48
48
48
48
50
50
49
49
52
52
49
49
53
48
53
54
48
16
16
16
32
32
32
32
32
32
16
16
16
16
16
16
16
16
16
16
32
16
32
32
16
16
32
16
32
32
16
16
16
16
16
32
32
32
32
32
32
32
32
32
32
32
16
32
32
16
16
32
16
16
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
1
N
N
N
1
N
N
N
N
N
N
N
N
N
N
DSP Type
RvbHall1
GateRvb2
Equalize
RvbHall1
Equalize
Enhancer
Reflect
CmpChoRf
Equalize
Cho Flan
Equalize
RvbHall1
Reflect
Enha Dly
ChoDly 1
Chorus 4
Equalize
RvbRoom2
CmpChoRf
Chorus 3
Chorus 3
Cho Trem
Auto Pan
CmpChoRf
Equalize
CmpChoRf
Equalize
Auto Wah
PhaAPan1
Equalize
StPhaser
Equalize
Enha Dly
ChoDly 1
Auto Wah
CmpEnDly
Cho Trem
Reflect
Reflect
Reflect
Reflect
PhaDly 2
PhaDly 2
3Tap Dly
RotRef 1
RotRef 2
Rotary 1
Cho Trem
RotRef 1
Rotary 2
Rotary 2
RotRef 1
RvbHall2
A-1
735A-E–115A
WK3000_e_A-01-16.p65
Range
Type
1
04.3.26, 0:12 PM
Appendix
No.
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
Tone Group
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
ORGAN
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
GUITAR
BASS
BASS
BASS
BASS
BASS
BASS
BASS
BASS
BASS
BASS
BASS
BASS
BASS
BASS
Tone Name
CHAPEL ORGAN
ACCORDION
HARMONICA
BANDONEON
DRAWBAR ORGAN 1
ELEC. ORGAN
DRAWBAR ORGAN 2
OVD ROTARY ORGAN
PERC. ORGAN 1
PERC. ORGAN 2
JAZZ ORGAN
OVD ROCK ORGAN
CHURCH ORGAN 2
OCTAVE ACCORDION
SLOW HARMONICA
NEO BANDONEON
NYLON GUITAR
STEEL GUITAR
JAZZ GUITAR
CHORUS CLEAN GUITAR
CRUNCH ELEC. GUITAR
OVD FRONT GUITAR
FEEDBACK DIST. GT
ROTARY GUITAR
MUTED DIST. GUITAR
MELLOW NYLON GUITAR
ENHANCED STEEL GUITAR
12 STRING GUITAR
CHORUS STEEL GUITAR
UKULELE
BANJO
OCT JAZZ GUITAR
OVERDRIVE GUITAR
AUTO WAH OVERDRIVE GT
OVD REAR GUITAR
MORE DISTORTION GT
DISTORTION FRONT GT
CLEAN GUITAR
ELEC. GUITAR FRONT
ELEC. GUITAR REAR
MUTED GUITAR
DISTORTION GUITAR
FEEDBACK GUITAR
DISTORTION CLEAN GT
ACOUSTIC BASS
FINGERED BASS
PICKED BASS
FRETLESS BASS
SLAP BASS
SAW SYNTH-BASS 1
ANALOG SYNTH-BASS
SQR SYNTH-BASS 1
RESO. SQR BASS 1
RESO. SAW BASS 1
DISTORTION SQR BASS
RESO. SAW BASS 2
DIGITAL BASS 1
RIDE BASS
Program
Change
19
21
22
23
16
16
16
16
17
17
17
18
19
21
22
23
24
25
26
27
27
29
30
27
28
24
25
25
25
24
105
26
29
29
29
30
30
27
27
27
28
30
30
30
32
33
34
35
37
38
38
39
39
38
39
38
39
32
Bank Select Maximum
MSB
Polyphony
51
48
48
48
48
51
50
54
48
51
50
49
49
49
49
49
48
48
48
49
52
49
52
53
49
51
51
49
50
49
48
50
48
51
50
51
50
48
51
50
48
48
49
53
48
48
48
48
48
48
52
48
50
53
51
49
52
49
32
16
32
16
32
32
32
32
16
16
16
16
16
16
32
16
32
32
32
32
32
32
16
32
32
16
32
16
16
32
32
16
16
16
32
16
32
32
32
32
32
16
16
32
32
32
32
32
32
16
32
32
32
32
16
16
32
16
A-2
WK3000_e_A-01-16.p65
Range
Type
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
N
N
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
DSP Type
RvbHall2
Reflect
Reflect
Reflect
Reflect
Reflect
Rotary 1
Od Rot 2
Reflect
Rotary 2
Reflect
OdRtRef1
RvbHall1
CmpChoRf
RvbRoom2
ChoDly 4
Equalize
Equalize
CmpChoRf
CmpChoRf
CrnDelay
CmpOdDly
DistDly1
Rotary 2
MetalDly
ChoDly 3
Enha Dly
Equalize
ChoDly 4
CmpChoRf
Equalize
RvbRoom3
CmpDelay
AWhOdDly
Ovrdrive
DistDly2
DistDly2
Equalize
Equalize
Equalize
Equalize
CmpDelay
CmpCrDly
CmpCrDly
Reflect
Limiter
Comp 2
ChoDly 1
Comp 2
Chorus 1
PhaCho 1
Od Rot 1
Enha Cho
AWhChDly
DistDly1
PhaDly 2
Comp 2
RvbRoom1
735A-E–116A
2
04.3.26, 0:12 PM
Appendix
No.
Tone Group
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
BASS
BASS
BASS
BASS
BASS
BASS
BASS
BASS
BASS
BASS
ORCHESTRA
ORCHESTRA
ORCHESTRA
ORCHESTRA
ORCHESTRA
ORCHESTRA
ORCHESTRA
ORCHESTRA
ORCHESTRA
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
ENSEMBLE
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
Tone Name
CHORUS FINGERED BASS
COMP. PICKED BASS
FLAN. FRETLESS BASS
MORE SLAP BASS
ACID BASS
SAW SYNTH-BASS 2
TRI SYNTH-BASS 1
SINE BASS
ORGAN BASS 1
DIGITAL BASS 2
VIOLIN
CELLO
VIOLA
PIZZICATO ENSEMBLE
HARP
SLOW VIOLIN
SLOW CELLO
PIZZICATO
HARPS
STEREO STRINGS
STRING ENSEMBLE
SLOW STRINGS
CHAMBER
PURE SYNTH-STRINGS 1
SYNTH-STRINGS 1
STEREO CHOIR
VOICE UUH
SYNTH-VOICE 1
SYNTH-VOICE 2
POP HIT 1
POP HIT 2
RESO SYNTH-STRINGS
SYNTH-CHOIR
VOICE DOO
BRIGHT STRINGS
WIDE STRINGS
MELLOW STRINGS
ORCHESTRA STRINGS 1
PURE SYNTH-STRINGS 2
PHASER SYNTH-STRINGS
SYNTH-DOO
SYNTH-VOICE 3
VOICE PAD
CHOIR STRINGS
ORCHESTRA STRINGS 2
BLOW VOICE
NOISY SYNTH-VOICE
BASS HIT
PIANO HIT
ORGAN HIT
ORCHESTRA HIT 1
TECHNO HIT
VELO. TRUMPET
VELO. TROMBONE
MUTE TRUMPET
OCTAVE FRENCH HORN
STEREO BRASS
BRASS + SYNTH
Program
Change
33
34
35
37
38
38
39
39
38
39
40
42
41
45
46
40
42
45
46
48
48
49
49
50
50
52
53
54
54
55
55
51
52
53
48
48
49
49
50
51
53
54
54
48
49
54
54
55
55
55
55
55
56
57
59
60
61
61
Bank Select Maximum
MSB
Polyphony
49
16
49
16
49
16
49
16
50
32
54
32
53
32
54
32
55
32
55
16
48
32
48
32
48
32
49
16
48
32
49
32
49
32
48
32
49
16
51
16
48
32
48
32
49
16
50
16
48
32
50
16
49
16
48
32
49
32
52
16
53
16
48
32
51
16
48
32
49
32
52
16
50
32
51
16
51
16
49
16
50
16
52
16
53
16
53
16
52
16
51
16
54
16
49
16
54
16
55
16
48
16
56
16
51
16
50
16
48
32
50
16
50
16
51
16
DSP Type
Crn Cho
CmpEnDly
Cho Flan
Comp 2
Enhancer
Equalize
Equalize
Limiter
Comp 1
Chorus 2
GateRvb2
GateRvb2
GateRvb2
RvbHall1
Reflect
RvbHall2
RvbHall2
Reflect
Reflect
RvbHall1
RvbRoom3
ChoDly 3
Reflect
ChoDly 3
ChoDly 3
RvbHall1
RvbRoom1
Chorus 4
ChoDly 3
Equalize
FlanDly1
ChoDly 3
StXDelay
RvbRoom1
RvbHall1
RvbHall1
RvbHall1
RvbRoom3
DistDly1
PhaAPan2
DistDly1
DistDly1
FlanDly3
RvbHall1
RvbHall1
DistDly1
FlanDly2
DistDly1
GateRvb2
Rotary 2
RvbHall1
MetalDly
GateRvb2
GateRvb2
Enhancer
RvbHall1
Enha Dly
Enha Dly
A-3
735A-E–117A
WK3000_e_A-01-16.p65
Range
Type
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
N
–1
N
N
N
N
–1
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
–1
N
–1
N
N
3
04.3.26, 0:12 PM
Appendix
No.
Tone Group
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
BRASS
REED
REED
REED
REED
REED
REED
REED
REED
REED
REED
REED
REED
REED
REED
REED
REED
REED
PIPE
PIPE
PIPE
PIPE
PIPE
PIPE
PIPE
PIPE
PIPE
PIPE
PIPE
PIPE
PIPE
PIPE
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
Tone Name
DEEP SYNTH-BRASS 1
SOFT SYNTH-BRASS
VINTAGE SYNTH-BRASS
TRUMPET 1
TRUMPET P
TROMBONE
TROMBONE F
WAH MUTE TRUMPET
FRENCH HORN
BRASS SFZ
DEEP SYNTH-BRASS 2
TUBA
SQR SYNTH-BRASS
WARM SYNTH-BRASS
ANALOG BRASS 1
BRASS + TRUMPET
SLOW SYNTH-BRASS
TROMBONE SECTION
BRASS
OCTAVE BRASS
ANALOG BRASS 2
BRASS + FRENCH HORN
STACK TUBA
BREATHY TENOR SAX
BREATHY ALTO SAX
MELLOW SOPRANO SAX
VELO. TENOR SAX
VELO. ALTO SAX
VELO. CLARINET
OBOE
SOPRANO SAX
ALTO SAX
TENOR SAX
ALTO SAX FF
BARITONE SAX
CLARINET
ALTO SAXYS
TENOR SAXYS
STACK BARITONE SAX
SYNTH-OBOE
VELO. FLUTE
PICCOLO
PAN FLUTE
BOTTLE BLOW
RECORDER
WHISTLES
FLUTE
PICCOLO ENSEMBLE
MELLOW FLUTE
OCTAVE FLUTE
FLUTE + REED
SYNTH-PAN FLUTE
SYNTH-RECORDER
WHISTLE
SAW TOOTH LEAD
MELLOW SAW LEAD
GR LEAD 1
SQUARE LEAD 1
Program
Change
62
63
63
56
56
57
57
59
60
61
62
58
62
63
62
61
63
57
61
61
62
61
58
66
65
64
66
65
71
68
64
65
66
65
67
71
65
66
67
68
73
72
75
76
74
78
73
72
73
73
73
75
74
78
81
81
81
80
Bank Select Maximum
MSB
Polyphony
51
51
48
48
50
48
49
49
48
53
53
48
52
52
48
52
49
51
48
54
54
55
49
49
49
49
50
51
49
48
48
48
48
50
48
48
52
51
49
49
49
48
48
48
48
49
48
49
50
51
52
49
49
48
48
53
54
48
16
16
16
32
16
16
32
32
16
16
16
32
16
16
32
16
16
16
32
16
32
16
16
16
16
16
16
32
16
32
32
32
32
32
32
32
16
16
16
16
16
32
32
32
32
16
32
16
16
16
16
16
16
32
16
16
16
16
A-4
WK3000_e_A-01-16.p65
Range
Type
N
N
N
N
N
–1
–1
N
–1
N
N
–1
N
N
N
N
N
N
N
N
N
N
–1
–1
–1
N
–1
–1
N
N
N
–1
–1
–1
–1
N
–1
–1
–1
N
N
1
N
N
N
N
N
1
N
N
N
N
N
N
N
N
N
N
DSP Type
Enha Dly
Enha Dly
RvbHall2
RvbHall1
RvbHall1
RvbHall1
RvbHall1
LFO Wah
RvbHall1
Comp 2
Enha Dly
RvbHall1
Delay
Delay
Comp 2
RvbHall2
ChoDly 4
GateRvb2
RvbHall2
RvbHall2
Equalize
RvbHall2
Comp 2
Enhancer
Enhancer
CmpEnDly
GateRvb2
GateRvb2
Reflect
GateRvb2
Equalize
Equalize
Equalize
Equalize
Equalize
GateRvb2
Equalize
Equalize
Comp 2
ChoDly 4
GateRvb2
Equalize
GateRvb2
Equalize
GateRvb2
ChoDly 4
Reflect
Equalize
Reflect
Equalize
StXDelay
AWhChDly
ChoDly 4
Od Rot 2
Enha Dly
Enha Dly
PhaDly 2
ChoDly 2
735A-E–118A
4
04.3.26, 0:12 PM
Appendix
No.
Tone Group
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-LEAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
Tone Name
SQUARE LEAD 2
VOX SQR LEAD
CALLIOPE LEAD
CHIFF LEAD 1
CHARANG LEAD
GT SYNTH-LEAD 1
SOLO VOX
FIFTH LEAD
HUSKY SAW
BASS LEAD 1
BASS LEAD 2
VOX SAW LEAD
SQUARE LEAD 3
MELLOW SQR LEAD
ADVANCED CALLIOPE
SEQ SAW 1
REED SAW
PIPE LEAD
ATTACK SQR 1
PERC. CHIFF 1
PLUCK LEAD 1
VOX LEAD 1
5TH MELLOW
4TH LEAD
REED LEAD
RESO. SAW LEAD
GR LEAD 2
DETUNED SAW
ATTACK SQR 2
SQUARE WAVE 1
SQUARE WAVE 2
CHIFF LEAD 2
PLUCK LEAD 2
TECH POLYSYNTH 1
RESO LEAD
FRET LEAD
TECH POLYSYNTH 2
7TH SEQ
FANTASY PAD
WARM PAD
POLYSYNTH PAD
NOISY SAW
SINE PAD
SPACE VOICE 1
COSMIC VOICE
BOWED PAD
METAL PAD 1
HALO PAD
SWEEP PAD
RAIN PAD
VIBE PAD
MOVIE SOUND
CRYSTAL PAD 2
ATMOSPHERE PAD
BRIGHTER
GOBLIN PAD
STAR THEME
NEW FANTASY
Program
Change
80
80
82
83
84
84
85
86
86
87
87
81
80
80
82
81
81
82
80
83
84
85
86
86
87
81
81
81
80
80
80
83
84
86
86
87
86
86
88
89
90
90
89
91
91
92
93
94
95
96
96
97
98
99
100
101
103
88
Bank Select Maximum
MSB
Polyphony
51
52
48
48
48
49
48
48
49
48
50
57
53
54
49
55
56
50
55
49
50
50
50
51
51
58
59
51
56
49
57
50
51
52
53
52
54
55
48
48
48
49
49
48
50
48
48
48
48
48
49
48
50
48
49
48
48
49
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
32
16
16
32
32
16
16
16
16
16
32
16
16
32
16
16
16
16
16
16
16
16
32
16
16
16
16
16
16
16
16
16
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
DSP Type
ChoDly 2
ChoDly 4
Equalize
Comp 1
Equalize
PhaAPan1
PhaDly 1
Auto Wah
PhaDly 1
Chorus 2
LFO Wah
RgChoDly
FlanDly1
Tremolo
RvbPlate
Equalize
Enha Cho
Reflect
Comp 2
Comp 1
FlanDly2
FlanDly2
StXDelay
Auto Pan
Equalize
Phaser
CmpCrDly
Chorus 2
3Tap Dly
Auto Pan
AWhChDly
Comp 1
FlanDly2
Ring Mod
Enha Dly
Enha Dly
LoFi Ref
Phaser
PhaDly 2
Equalize
Cho Trem
Lo-Fi
Phaser
RotRef 1
Rotary 2
3Tap Dly
St Delay
StPhaser
Equalize
Comp 1
CmpDelay
FlanDly1
St Delay
GateRvb1
Delay
Flanger
PhaAPan2
ChoDly 3
A-5
735A-E–119A
WK3000_e_A-01-16.p65
Range
Type
5
04.3.26, 0:12 PM
Appendix
No.
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
Tone Group
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
SYNTH-PAD
Tone Name
WARM VOX
FLUTE PAD
ATTACK POLYSYNTH
CHIFF CHOIR
STAR VOICE
SPACE VOICE 2
GLASS PAD
BOTTLE PAD
METAL VOICE
BRIGHTNESS PAD
CRYSTAL PAD 1
POLY SAW
BOUNCE PAD
SLOW SWEEP
STEEL PAD
Program
Change
89
89
90
91
91
91
92
92
93
100
98
90
94
95
99
Bank Select Maximum
MSB
Polyphony
50
51
50
51
52
49
50
49
49
48
48
51
49
49
49
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
Range
Type
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
DSP Type
Equalize
Equalize
Equalize
Cho Flan
DsChoDly
RgChoDly
Equalize
LFO Wah
RotRef 1
ChoDly 2
PhaDly 2
ChoDly 3
Dist Cho
RgChoDly
ChoDly 3
Preset Tones
No.
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
Tone Group
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
Tone Name
PIANO 1
PIANO 2
PIANO 3
HONKY-TONK GM
ELEC. PIANO 1 GM
MODERN EP 1 GM
HARPSICHORD GM
CLAVI GM
CELESTA GM
GLOCKENSPIEL GM
MUSIC BOX
VIBRAPHONE GM
MARIMBA GM
XYLOPHONE
TUBULAR BELL
DULCIMER
DRAWBAR ORGAN 1 GM
PERC. ORGAN 1 GM
ROCK ORGAN GM
CHURCH ORGAN 1 GM
REED ORGAN
ACCORDION GM
HARMONICA GM
BANDONEON GM
NYLON GUITAR GM
STEEL GUITAR GM
JAZZ GUITAR GM
CLEAN GUITAR GM
MUTED GUITAR GM
OVERDRIVE GT GM
DISTORTION GT GM
GUITAR HARMONICS
ACOUSTIC BASS GM
FINGERED BASS GM
PICKED BASS GM
FRETLESS BASS GM
Program
Change
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
Bank Select Maximum
MSB
Polyphony
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
32
32
32
16
32
16
32
32
32
32
16
32
32
32
32
16
32
16
16
16
32
16
32
16
32
32
32
32
32
16
16
32
32
32
32
32
A-6
WK3000_e_A-01-16.p65
Range
Type
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
DSP Type
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
735A-E–120A
6
04.3.26, 0:12 PM
Appendix
No.
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
Tone Group
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
Tone Name
SLAP BASS 1
SLAP BASS 2 GM
SAW SYNTH-BASS 1 GM
SQR SYNTH-BASS 1 GM
VIOLIN GM
VIOLA GM
CELLO GM
CONTRABASS
TREMOLO STRINGS
PIZZICATO GM
HARP GM
TIMPANI
STRINGS 1
STRINGS 2
SYNTH-STRINGS 1 GM
RESO SYNTH-STRINGS GM
CHOIR
VOICE DOO GM
SYNTH-VOICE 1 GM
ORCHESTRA HIT 1 GM
TRUMPET 1 GM
TROMBONE GM
TUBA GM
MUTE TRUMPET GM
FRENCH HORN GM
BRASS GM
SYNTH-BRASS 1
SYNTH-BRASS 2
SOPRANO SAX GM
ALTO SAX GM
TENOR SAX GM
BARITONE SAX GM
OBOE GM
ENGLISH HORN
BASSOON
CLARINET GM
PICCOLO GM
FLUTE GM
RECORDER GM
PAN FLUTE GM
BOTTLE BLOW GM
SHAKUHACHI
WHISTLE GM
OCARINA
SQUARE LEAD
PLAIN SAW LEAD
CALLIOPE
CHIFF
CHARANG
PLAIN SOLO VOX
FIFTH SAW
BASS LEAD
FANTASY
WARM SYNTH
POLYSYNTH
SPACE VOX
BOWED GLASS
METAL SYNTH
Program
Change
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
Bank Select Maximum
MSB
Polyphony
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
32
32
16
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
16
32
32
32
32
16
32
32
16
32
32
32
32
32
32
32
32
32
32
32
32
32
16
32
32
16
16
16
16
16
16
16
16
16
32
16
16
16
16
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
DSP Type
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
A-7
735A-E–121A
WK3000_e_A-01-16.p65
Range
Type
7
04.3.26, 0:12 PM
Appendix
No.
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
Tone Group
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
GM
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
Tone Name
HALO SYNTH
SWEEP
RAIN DROP
SOUND TRACK
CRYSTAL
ATMOSPHERE
BRIGHTNESS
GOBLIN
ECHOES
SF
SITAR
BANJO GM
SHAMISEN
KOTO
THUMB PIANO
BAG PIPE
FIDDLE
SHANAI
TINKLE BELL
AGOGO
STEEL DRUMS
WOOD BLOCK
TAIKO
MELODIC TOM
SYNTH-DRUM
REVERSE CYMBAL
GT FRET NOISE
BREATH NOISE
SEASHORE
BIRD
TELEPHONE
HELICOPTER
APPLAUSE
GUNSHOT
PIANO 1 WIDE
MELLOW PIANO GM
PIANO 2 WIDE
TECHNO PIANO
MODERN E.G.PIANO WIDE
HONKY-TONK 2
ELEC. PIANO 2
60’S E.PIANO GM
MODERN EP + E.G.PIANO
MODERN EP 3
HARPSICHORD WIDE
PULSE CLAVI GM
VIBRAPHONE WIDE
MARIMBA WIDE
TREMOLO ORGAN GM
DRAWBAR ORGAN 2 GM
70’S ORGAN GM
JAZZ ORGAN GM
CHURCH ORGAN 2 GM
CHURCH ORGAN 3
PUFF ORGAN
NYLON GUITAR RLS
12 STRING GUITAR GM
PEDAL STEEL
Program
Change
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
0
0
1
1
2
3
4
4
5
5
6
7
11
12
16
16
17
17
19
19
20
24
25
26
Bank Select Maximum
MSB
Polyphony
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
65
66
65
70
65
65
65
67
65
67
66
65
65
65
65
66
65
66
65
66
65
66
65
65
16
32
16
16
16
16
16
16
32
16
16
32
32
32
32
16
32
32
32
32
16
32
32
32
32
32
32
32
16
16
32
32
16
32
32
32
32
32
32
16
16
32
16
16
32
32
32
32
32
32
32
16
16
16
16
16
16
16
A-8
WK3000_e_A-01-16.p65
Range
Type
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
DSP Type
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
735A-E–122A
8
04.3.26, 0:12 PM
Appendix
No.
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
Tone Group
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
VARIOUS
Tone Name
DETUNED CLEAN GT
PLAIN ELEC. GUITAR REAR
PLAIN ELEC. GUITAR FRONT
FEEDBACK GUITAR GM
GUITAR FEEDBACK
SAW SYNTH-BASS 3
RESO. SAW BASS 3
SAW SYNTH-BASS 4
ORGAN BASS 2
SQR SYNTH-BASS 2
KICK BASS 1
SQR SYNTH-BASS 3
ATTACK SQR BASS
BRIGHT STRINGS GM
OCTAVE STRINGS
SYNTH-STRINGS 2
PURE SYNTH-STRING
CHOIR + UUH
VOICE UUH GM
SYNTH-VOICE 2 GM
SEQ VOX
BASS HIT GM
POP HIT 3
ORCHESTRA HIT 2
TIMPANI HIT
TRUMPET 2
TROMBONE F GM
MELLOW FRENCH HORN
BRASS + TROMBONE
SYNTH-BRASS 3
OCTAVE SYNTH-BRASS
SYNTH-BRASS SFZ
BS SYNTH-BRASS
SQUARE WAVE
TRIANGLE WAVE
SQUARE WAVE 3
SAW WAVE
SAW + SQR
SEQ SAW 2
PERC. CHIFF 2
GT SYNTH-LEAD 2
VOX LEAD 2
BASS LEAD 3
SINE SYNTH
SOPRANO PAD
FAST SWEEP
WOOD PAD
SYNTH-MALLET
Program
Change
27
27
27
30
31
38
38
38
38
39
39
39
39
48
48
50
50
52
53
54
54
55
55
55
55
56
57
60
61
62
62
63
63
80
80
80
81
81
81
83
84
85
87
89
89
95
96
98
Bank Select Maximum
MSB
Polyphony
65
66
67
65
65
67
72
73
74
65
72
73
74
65
66
65
66
65
65
65
66
65
66
67
73
65
65
65
65
65
66
65
66
65
66
74
65
66
68
67
68
65
65
65
68
66
66
65
16
32
32
16
32
16
16
16
16
16
16
16
16
32
16
16
16
16
16
32
32
16
16
16
16
32
32
16
16
32
16
16
16
32
32
32
32
16
16
16
16
16
16
16
16
16
16
16
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
DSP Type
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
A-9
735A-E–123A
WK3000_e_A-01-16.p65
Range
Type
9
04.3.26, 0:12 PM
Appendix
Drum Sets
No.
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
Tone Group
DRUM
DRUM
DRUM
DRUM
DRUM
DRUM
DRUM
DRUM
DRUM
DRUM
DRUM
DRUM
DRUM
DRUM
DRUM
DRUM
Tone Name
STANDARD SET 1
STANDARD SET 2
ROOM SET
POWER SET
ELEC. SET
SYNTH SET 1
SYNTH SET 2
JAZZ SET
BRUSH SET
ORCHESTRA SET
HIP-HOP SET 1
HIP-HOP SET 2
TECHNO SET 1
TECHNO SET 2
DANCE SET 1
DANCE SET 2
Program
Change
Bank Select
MSB
0
1
8
16
24
25
30
32
40
48
64
65
66
67
68
69
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
Drawbar Organ Tones
No.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Tone Group
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
Tone Name
Drawbar Organ 1
Jazz Organ 1
Full Drawbar
Perc. Organ 1
16’+1’ Organ
Soul Organ 1
Overdrive Organ 1
Drawbar Organ 2
Block Organ 1
Theater Organ 1
Jazz Organ 2
Soul Organ 2
Gospel Organ 1
Chorus Organ 1
Overdrive Organ 2
Block Organ 2
Drawbar Organ 3
Perc. Organ 2
Theater Organ 2
Gospel Organ 2
Even Organ
Flute Organ 1
Chorus Organ 2
Overdrive Organ 3
16’ Organ
Soul Organ 3
Perc. Organ 3
Drawbar Organ 4
Perc. Organ 4
Odd Organ
Reed Organ 1
Block Organ 3
Program
Change
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Bank Select Maximum
MSB
Polyphony
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
10
10
16
16
16
10
16
16
16
16
10
16
16
16
10
16
16
16
16
16
16
16
16
16
16
16
16
16
10
16
16
10
A-10
WK3000_e_A-01-16.p65
Range
Type
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
DSP Type
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
OvdRotry
Rotary
OvdRotry
Rotary
Rotary
Rotary
Rotary
Rotary
OvdRotry
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
735A-E–124A
10
04.3.26, 0:12 PM
Appendix
No.
Tone Group
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
DRAWBAR
Tone Name
Overdrive Organ 4
Drawbar Organ 5
Gospel Organ 3
8’ + 4’ Organ
Block Organ 4
String Organ 2
Pure Organ 1
Drawbar Organ 6
Delay Organ 1
Deep Chorus Organ
Tremolo Organ
Delay Organ 2
LFO Wah Organ
Dist. Organ Lead
Ring Organ
Mad Rotary Organ
Old Organ
Dist. Ring Organ
Program
Change
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
Bank Select Maximum
MSB
Polyphony
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
96
10
10
16
32
32
16
32
10
10
32
16
16
16
16
16
10
16
10
Range
Type
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
DSP Type
OvdRotry
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
Rotary
StXDly 2
Cho.Dly4
Cho.Trem
Cho.Dly6
LWhChDl2
MetalDly
RingMod2
RgChDly2
LoFiRef2
DistRing
NOTE
Range
Symbol
N
–1
–2
1
2
1/2
1/4
Meaning
Normal
1 Octave Down
2 Octave Down
1 Octave Up
2 Octave Up
1/2 Octave
1/4 Octave
User Tones
No.
Tone Type
Standard Tone
600-699 User Tones
700-719 User Tones with Waves
800-803 User Drum Sets with Waves
Drawbar Organ Tones
100-199 User Tones
Program Change
Bank Select MSB
000-099
000-019
000-003
094
088
125
000-099
104
A-11
735A-E–125C
WK3000_e_A-01-16.p65
11
04.3.26, 0:12 PM
Appendix
Drum Assignment List
➝
“
” indicates the same sound as STANDARD SET.
Key/
Note number
A0 21
B0 23
C1 24
D1 26
E1 28
F1 29
G1 31
A1 33
B1 35
C2 36
D2 38
E2 40
F2 41
B 0 22
C#1 25
E 1 27
F#1 30
A 1 32
B 1 34
C#2 37
E 2 39
F#2 42
G2 43
A 2 44
A2 45
B 2 46
B2 47
C3 48
D3 50
E3 52
F3 53
C#3 49
E 3 51
F#3 54
G3 55
A 3 56
A3 57
B 3 58
B3 59
C4 60
D4 62
E4 64
F4 65
C#4 61
E 4 63
F#4 66
G4 67
A4 68
A4 69
B4 70
B4 71
C5 72
D5 74
C#5 73
E 5 75
E5 76
F5 77
F#5 78
G5 79
A 5 80
A5 81
B 5 82
B5 83
C6 84
D6 86
E6 88
F6 89
C#6 85
E 6 87
F#6 90
G6 91
A 6 92
A6 93
B 6 94
B6 95
C7 96
D7 98
E7 100
F7 101
C#7 97
E 7 99
F#7 102
G7 103
A 7 104
A7 105
B 7 106
B7 107
C8 108
D8 110
E8 112
C#8 109
E 8 111
Program Change No. / Drum Set Name
PC0: STANDARD SET 1 PC1: STANDARD SET 2 PC8: ROOM SET PC16: POWER SET PC24: ELEC SET
—
—
—
—
—
—
HIGH Q
SLAP
SCRATCH PUSH
SCRATCH PULL
STICKS
SQUARE CLICK
METRONOME CLICK
METRONOME BELL
STANDARD 1 KICK 2
STANDARD 1 KICK 1
SIDE STICK
STANDARD 1 SNARE 1
HAND CLAP
STANDARD 1 SNARE 2
LOW TOM 2
CLOSED HI-HAT
LOW TOM 1
PEDAL HI-HAT
MID TOM 2
OPEN HI-HAT
MID TOM 1
HIGH TOM 2
CRASH CYMBAL 1
HIGH TOM 1
RIDE CYMBAL 1
CHINESE CYMBAL
RIDE BELL
TAMBOURINE
SPLASH CYMBAL
COWBELL
CRASH CYMBAL 2
VIBRA-SLAP
RIDE CYMBAL 2
HIGH BONGO
LOW BONGO
MUTE HIGH CONGA
OPEN HIGH CONGA
LOW CONGA
HIGH TIMBALE
LOW TIMBALE
HIGH AGOGO
LOW AGOGO
CABASA
MARACAS
SHORT HI WHISTLE
LONG LOW WHISTLE
SHORT GUIRO
LONG GUIRO
CLAVES
HIGH WOOD BLOCK
LOW WOOD BLOCK
MUTE CUICA
OPEN CUICA
MUTE TRIANGLE
OPEN TRIANGLE
SHAKER
JINGLE BELL
BELL TREE
CASTANETS
MUTE SURDO
OPEN SURDO
APPLAUSE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
씯
씯
씯
씯
씯
씯
씯
씯
STANDARD 2 KICK 2
STANDARD 2 KICK 1
씯
STANDARD 1 SNARE 1
SYNTH HAND CLAP
STANDARD 1 SNARE 2
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
씯
씯
씯
씯
씯
씯
씯
씯
ROOM KICK 2
ROOM KICK 1
씯
ROOM SNARE 1
씯
ROOM SNARE 2
ROOM LOW TOM 2
씯
ROOM LOW TOM 1
씯
ROOM MID TOM 2
씯
ROOM MID TOM 1
ROOM HI TOM 2
씯
ROOM HI TOM 1
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
씯
씯
씯
씯
씯
씯
씯
씯
POWER KICK 2
POWER KICK 1
씯
POWER SNARE 1
씯
POWER SNARE 2
ROOM LOW TOM 2
씯
ROOM LOW TOM 1
씯
ROOM MID TOM 2
씯
ROOM MID TOM 1
ROOM HI TOM 2
씯
ROOM HI TOM 1
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
씯
씯
씯
씯
씯
씯
씯
씯
ELEC KICK 2
ELEC KICK 1
씯
ELEC SNARE 1
씯
ELEC SNARE 2
ELEC LOW TOM 2
씯
ELEC LOW TOM 1
씯
ELEC MID TOM 2
씯
ELEC MID TOM 1
ELEC HI TOM 2
씯
ELEC HI TOM 1
씯
REVERSE CYMBAL
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
PC25: SYNTH 1
PC30: SYNTH 2
—
—
—
—
—
—
씯
씯
씯
씯
씯
씯
씯
씯
SYNTH 1 KICK 1
SYNTH 1 KICK 2
SYNTH 1 RIM SHOT
SYNTH 1 SNARE 1
SYNTH HAND CLAP
SYNTH 1 SNARE 2
SYNTH 1 LOW TOM 2
SYNTH 1 CHH 1
SYNTH 1 LOW TOM 1
SYNTH 1 CHH 2
SYNTH 1 MID TOM 2
SYNTH 1 OHH
SYNTH 1 MID TOM 1
SYNTH 1 HI TOM 2
SYNTH 1 CYMBAL
SYNTH 1 HI TOM 1
씯
씯
씯
씯
씯
SYNTH 1 COWBELL
씯
씯
씯
씯
씯
SYNTH 1 HIGH CONGA
SYNTH 1 MID CONGA
SYNTH 1 LOW CONGA
씯
씯
씯
씯
씯
SYNTH 1 MARACAS
씯
씯
씯
씯
SYNTH 1 CLAVES
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
씯
씯
씯
씯
씯
씯
씯
씯
SYNTH 2 KICK 1
SYNTH 2 KICK 2
씯
SYNTH 2 SNARE 1
씯
SYNTH 2 SNARE 2
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
SYNTH 1 COWBELL
씯
씯
씯
씯
씯
SYNTH 1 HIGH CONGA
SYNTH 1 MID CONGA
SYNTH 1 LOW CONGA
씯
씯
씯
씯
씯
SYNTH 1 MARACAS
씯
씯
씯
씯
SYNTH 1 CLAVES
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
A-12
WK3000_e_A-01-16.p65
PC32: JAZZ SET
—
—
—
—
—
—
씯
씯
씯
씯
씯
씯
씯
씯
JAZZ KICK 2
JAZZ KICK 1
씯
JAZZ SNARE 1
씯
JAZZ SNARE 2
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
735A-E–126A
12
04.3.26, 0:12 PM
Appendix
Key/
Note number
A0 21
B0 23
C1 24
D1 26
E1 28
F1 29
G1 31
A1 33
B1 35
C2 36
D2 38
E2 40
F2 41
B 0 22
C#1 25
E 1 27
F#1 30
A 1 32
B 1 34
C#2 37
E 2 39
F#2 42
G2 43
A 2 44
A2 45
B 2 46
B2 47
C3 48
D3 50
E3 52
F3 53
C#3 49
E 3 51
F#3 54
G3 55
A 3 56
A3 57
B 3 58
B3 59
C4 60
D4 62
E4 64
F4 65
C#4 61
E 4 63
F#4 66
G4 67
A4 68
A4 69
B4 70
B4 71
C5 72
D5 74
C#5 73
E 5 75
E5 76
F5 77
F#5 78
G5 79
A 5 80
A5 81
B 5 82
B5 83
C6 84
D6 86
E6 88
F6 89
C#6 85
E 6 87
F#6 90
G6 91
A 6 92
A6 93
B 6 94
B6 95
C7 96
D7 98
E7 100
F7 101
C#7 97
E 7 99
F#7 102
G7 103
A 7 104
A7 105
B 7 106
B7 107
C8 108
D8 110
C#8 109
E 8 111
E8 112
Program Change No. / Drum Set Name
PC40: BRUSH SET PC48: ORCHESTRA SET PC64: HIP-HOP SET 1 PC65: HIP-HOP SET 2 PC66: TECHNO SET 1 PC67: TECHNO SET 2 PC68: DANCE SET 1 PC69: DANCE SET 2
—
—
—
—
—
—
씯
씯
씯
씯
씯
씯
씯
씯
JAZZ KICK 2
JAZZ KICK 1
씯
BRUSH TAP
BRUSH SLAP
BRUSH SWIRL
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
CLOSED HI-HAT
PEDAL HI-HAT
OPEN HI-HAT
RIDE CYMBAL 1
씯
씯
씯
씯
JAZZ KICK 1
CONCERT BASS DRUM
씯
CONCERT SNARE
CASTANETS
CONCERT SNARE
TIMPANI F
TIMPANI F
TIMPANI G
TIMPANI A
TIMPANI A
TIMPANI B
TIMPANI B
TIMPANI C
TIMPANI C
TIMPANI D
TIMPANI E
TIMPANI E
TIMPANI F
씯
씯
씯
CONCERT CYMBAL 2
씯
CONCERT CYMBAL 1
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
WHITE NOISE
LOOPED
BEEP 1
BEEP 2
HIT 1
HIT 2
씯
씯
HIP-HOP SCRACH 1
HIP-HOP SCRACH 2
씯
씯
씯
씯
HIP-HOP KICK 2
HIP-HOP KICK 1
씯
HIP-HOP SNARE 1
HAND CLAP 2
HIP-HOP SNARE 2
씯
HIP-HOP CHH
씯
HIP-HOP PHH
씯
HIP-HOP OHH
씯
씯
HIP-HOP CLASH
씯
HIP-HOP RIDE
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
ELEC KICK 1
SYNTH 1 KICK 1
SYNTH 1 KICK 2
DANCE KICK 3
TECHNO KICK 1
HIP-HOP BD 5
HIP-HOP BD 6
TECHNO KICK 4
DANCE KICK 2
DANCE KICK 1
DANCE KICK 5
DANCE KICK 6
POWER SNARE 2
SYNTH 1 SNARE 1
SYNTH 1 SNARE 2
SYNTH 2 SNARE 1
SYNTH 2 SNARE 2
HIP-HOP SNARE 5
HIP-HOP SNARE 6
TECHNO SNARE 3
TECHNO SNARE 5
TECHNO SNARE 6
DANCE SNARE 4
DANCE SNARE 5
WHITE NOISE
LOOPED
BEEP 1
BEEP 2
HIT 1
HIT 2
씯
씯
HIP-HOP SCRACH 1
HIP-HOP SCRACH 2
씯
씯
씯
씯
HIP-HOP KICK 4
HIP-HOP KICK 3
씯
HIP-HOP SNARE 3
HAND CLAP 2
HIP-HOP SNARE 4
SYNTH 2 LOW TOM 2
HIP-HOP CHH
SYNTH 2 LOW TOM 1
HIP-HOP PHH
SYNTH 2 MID TOM 2
HIP-HOP OHH
SYNTH 2 MID TOM 1
SYNTH 2 HI TOM 2
SYNTH 2 CYMBAL
SYNTH 2 HI TOM 1
SYNTH 2 RIDE
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
ELEC KICK 1
SYNTH 1 KICK 1
SYNTH 1 KICK 2
DANCE KICK 3
TECHNO KICK 1
HIP-HOP BD 5
HIP-HOP BD 6
TECHNO KICK 4
DANCE KICK 2
DANCE KICK 1
DANCE KICK 5
DANCE KICK 6
POWER SNARE 2
SYNTH 1 SNARE 1
SYNTH 1 SNARE 2
SYNTH 2 SNARE 1
SYNTH 2 SNARE 2
HIP-HOP SNARE 5
HIP-HOP SNARE 6
TECHNO SNARE 3
TECHNO SNARE 5
TECHNO SNARE 6
DANCE SNARE 4
DANCE SNARE 5
WHITE NOISE
LOOPED
BEEP 1
BEEP 2
HIT 1
HIT 2
씯
씯
HIP-HOP SCRACH 1
HIP-HOP SCRACH 2
씯
씯
씯
씯
TECHNO KICK 2
TECHNO KICK 1
SYNTH 1 RIM SHOT
TECHNO SNARE 1
HAND CLAP 3
TECHNO SNARE 2
SYNTH 1 LOW TOM 2
SYNTH 1 CHH
SYNTH 1 LOW TOM 1
SYNTH 1 PHH
SYNTH 1 MID TOM 2
SYNTH 1 OHH
SYNTH 1 MID TOM 1
SYNTH 1 HI TOM 2
SYNTH 1 CYMBAL
SYNTH 1 HI TOM 1
SYNTH 1 RIDE
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
ELEC KICK 1
SYNTH 1 KICK 1
SYNTH 1 KICK 2
DANCE KICK 3
TECHNO KICK 1
HIP-HOP BD 5
HIP-HOP BD 6
TECHNO KICK 4
DANCE KICK 2
DANCE KICK 1
DANCE KICK 5
DANCE KICK 6
POWER SNARE 2
SYNTH 1 SNARE 1
SYNTH 1 SNARE 2
SYNTH 2 SNARE 1
SYNTH 2 SNARE 2
HIP-HOP SNARE 5
HIP-HOP SNARE 6
TECHNO SNARE 3
TECHNO SNARE 5
TECHNO SNARE 6
DANCE SNARE 4
DANCE SNARE 5
WHITE NOISE
LOOPED
BEEP 1
BEEP 2
HIT 1
HIT 2
씯
씯
HIP-HOP SCRACH 1
HIP-HOP SCRACH 2
씯
씯
씯
씯
TECHNO KICK 4
TECHNO KICK 3
SYNTH 1 RIM SHOT
TECHNO SNARE 3
HAND CLAP 3
TECHNO SNARE 4
SYNTH 1 LOW TOM 2
TECHNO CHH 1
SYNTH 1 LOW TOM 1
TECHNO PHH
SYNTH 1 MID TOM 2
TECHNO OHH
SYNTH 1 MID TOM 1
SYNTH 1 HI TOM 2
TECHNO CYMBAL
SYNTH 1 HI TOM 1
TECHNO CYMBAL
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
ELEC KICK 1
SYNTH 1 KICK 1
SYNTH 1 KICK 2
DANCE KICK 3
TECHNO KICK 1
HIP-HOP BD 5
HIP-HOP BD 6
TECHNO KICK 4
DANCE KICK 2
DANCE KICK 1
DANCE KICK 5
DANCE KICK 6
POWER SNARE 2
SYNTH 1 SNARE 1
SYNTH 1 SNARE 2
SYNTH 2 SNARE 1
SYNTH 2 SNARE 2
HIP-HOP SNARE 5
HIP-HOP SNARE 6
TECHNO SNARE 3
TECHNO SNARE 5
TECHNO SNARE 6
DANCE SNARE 4
DANCE SNARE 5
WHITE NOISE
LOOPED
BEEP 1
BEEP 2
HIT 1
HIT 2
씯
씯
HIP-HOP SCRACH 1
HIP-HOP SCRACH 2
씯
씯
씯
씯
DANCE KICK 4
DANCE KICK 3
SYNTH 1 RIM SHOT
DANCE SNARE 3
HAND CLAP 3
DANCE SNARE 4
SYNTH 2 LOW TOM 2
HIP-HOP CHH
SYNTH 2 LOW TOM 1
HIP-HOP PHH
SYNTH 2 MID TOM 2
HIP-HOP OHH
SYNTH 2 MID TOM 1
SYNTH 2 HI TOM 2
TECHNO CYMBAL
SYNTH 2 HI TOM 1
TECHNO CYMBAL
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
ELEC KICK 1
SYNTH 1 KICK 1
SYNTH 1 KICK 2
DANCE KICK 3
TECHNO KICK 1
HIP-HOP BD 5
HIP-HOP BD 6
TECHNO KICK 4
DANCE KICK 2
DANCE KICK 1
DANCE KICK 5
DANCE KICK 6
POWER SNARE 2
SYNTH 1 SNARE 1
SYNTH 1 SNARE 2
SYNTH 2 SNARE 1
SYNTH 2 SNARE 2
HIP-HOP SNARE 5
HIP-HOP SNARE 6
TECHNO SNARE 3
TECHNO SNARE 5
TECHNO SNARE 6
DANCE SNARE 4
DANCE SNARE 5
A-13
735A-E–127A
WK3000_e_A-01-16.p65
WHITE NOISE
LOOPED
BEEP 1
BEEP 2
HIT 1
HIT 2
씯
씯
HIP-HOP SCRACH 1
HIP-HOP SCRACH 2
씯
씯
씯
씯
DANCE KICK 2
DANCE KICK 2
SYNTH 1 RIM SHOT
DANCE SNARE 1
HAND CLAP 3
DANCE SNARE 2
씯
SYNTH 2 CHH
씯
SYNTH 2 PHH
씯
SYNTH 2 OHH
씯
씯
HIP-HOP CLASH
씯
HIP-HOP RIDE
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
씯
ELEC KICK 1
SYNTH 1 KICK 1
SYNTH 1 KICK 2
DANCE KICK 3
TECHNO KICK 1
HIP-HOP BD 5
HIP-HOP BD 6
TECHNO KICK 4
DANCE KICK 2
DANCE KICK 1
DANCE KICK 5
DANCE KICK 6
POWER SNARE 2
SYNTH 1 SNARE 1
SYNTH 1 SNARE 2
SYNTH 2 SNARE 1
SYNTH 2 SNARE 2
HIP-HOP SNARE 5
HIP-HOP SNARE 6
TECHNO SNARE 3
TECHNO SNARE 5
TECHNO SNARE 6
DANCE SNARE 4
DANCE SNARE 5
13
04.3.26, 0:12 PM
Appendix
Rhythm List
No.
Rhythm Name
8 BEAT
0
8 BEAT 1
1
8 BEAT 2
2
8 BEAT 3
3
8 BEAT POP 1
4
8 BEAT POP 2
5
8 BEAT POP 3
6
60’S SOUL
7
8 BEAT DANCE
8
POP ROCK 1
9
POP ROCK 2
16 BEAT
10
16 BEAT 1
11
16 BEAT 2
12
16 BEAT 3
13
SLOW 16 BEAT
14
16 BEAT SHUFFLE 1
15
16 BEAT SHUFFLE 1
16
FUNK 1
17
FUNK 2
18
FUSION
19
LATIN FUSION
POPS
20
POP
21
SOUL
22
POP SHUFFLE 1
23
POP SHUFFLE 2
24
SOUL POP
25
WORLD POP
26
MELLOW R&B
27
60’S POP
28
80’S POP
29
POP WALTZ
BALLAD
30
8 BEAT BALLAD 1
31
8 BEAT BALLAD 2
32
8 BEAT BALLAD 3
33
16 BEAT BALLAD 1
34
16 BEAT BALLAD 2
35
16 BEAT BALLAD 3
36
6/8 BALLAD
37
POP BALLAD
38
OLDIES BALLAD
39
SERENADE
ROCK
40
ROCK 1
41
ROCK 2
42
R&B
43
SHUFFLE ROCK
44
SLOW ROCK
45
HEAVY METAL
46
60’S ROCK
47
SHUFFLE BOOGIE
48
BLUES
49
TWIST
DANCE
50
TRANCE 1
51
TRANCE 2
52
AMBIENT 1
53
AMBIENT 2
54
AMBIENT 3
55
RAVE
56
TECHNO
57
DIGITAL ROCK
58
HOUSE
59
LATIN HOUSE
60
DANCE 1
61
DANCE 2
62
MODERN R&B
63
HIP-HOP
64
TRIP-HOP
65
ELECTRIC POP
66
DANCE POP 1
67
DANCE POP 2
68
DANCE POP 3
69
DISCO SOUL
JAZZ
70
FAST BIG BAND
71
MIDDLE BIG BAND
72
SLOW BIG BAND
73
JAZZ COMBO
74
SWING
75
SLOW SWING
76
MODERAN JAZZ
77
FOX TROT
78
QUICKSTEP
79
JAZZ WALTZ
EUROPEAN
80
POLKA
81
POLKA FOX
82
POP POLKA
83
1.Mar
84
2.Mar
85
GERMAN MARCH
86
WALTZ 1
87
WALTZ 2
88
VINNESE WALTZ
89
FRENCH WALTZ
LATIN/VARIOUS
90
BOSSA NOVA 1
91
BOSSA NOVA 2
92
SAMBA
93
MERENGUE
94
CUMBIA
95
CHA-CHA-CHA
96
SALSA
97
BEGUINE
98
BOLERO
99
MAMBO
100
RHUMBA
101
TANGO 1
102
TANGO 2
103
REGGAE 1
104
REGGAE 2
105
SKA
106
BLUEGRASS
107
COUNTRY
108
COUNTRY SHUFFLE
109
COUNTRY WALTZ
110
FAST GOSPEL
111
SLOW GOSPEL
112
BROADWAY
113
JIVE
114
DIXIE
115
PASODOBLE
116
SIRTAKI
117
HAWAIAN
118
ADANI
119
BALADI
FOR PIANO
120
PIANO BALLAD 1
121
PIANO BALLAD 2
122
PIANO BALLAD 3
123
EP BALLAD 1
124
EP BALLAD 2
125
BLUES BALLAD
126
MELLOW JAZZ
127
JAZZ COMBO 2
128
RAGTIME
129
BOOGIE WOOGIE
130
ARPEGGIO 1
131
ARPEGGIO 2
132
ARPEGGIO 3
133
PIANO BALLAD 4
134
6/8 MARCH
135
3.Mar
136
2 BEAT
137
WALTZ 3
138
WALTZ 4
139
WALTZ 5
A-14
WK3000_e_A-01-16.p65
735A-E–128A
14
04.3.26, 0:12 PM
Appendix
Fingered Chord Chart
Chord
Type
Root
M
m
7
m7
dim7
M7
dim
m7-5
C
C /(D )
D
(D )/E E
F
F /(G )
G
(G )/A
A
(A )/B B
* You can use the above fingerings to finger chords within the accompaniment keyboard range.
A-15
735A-E–129A
WK3000_e_A-01-16.p65
15
04.3.26, 0:12 PM
Appendix
Chord
Type
Root
aug
sus4
7sus4
m add9
mM7
7-5
add9
C
C /(D )
D
(D )/E E
F
F /(G )
G
(G )/A
A
(A )/B B
A-16
WK3000_e_A-01-16.p65
735A-E–130A
16
04.3.26, 0:12 PM
WK3000_e_A-17-18.p65
17
Display Name
Standard
Bass +
Treble +
Loundness
Mellow
Bright
Rock
Dance
Jazz
Classic
No.
0
1
2
3
4
5
6
7
8
9
Equalizer List
Standard
Bass +
Treble +
Loundness
Mellow
Bright
Rock
Dance
Jazz
Classic
Type Name
Room 1
Room 2
Room 3
Hall 1
Hall 2
Plate 1
Delay
Pan Delay
Plate 2
Plate 3
Large Room 1
Large Room 2
Stadium 1
Stadium 2
Long Delay 1
Long Delay 2
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Room 1
Room 2
Room 3
Hall 1
Hall 2
Plate 1
Delay
PanDelay
Plate 2
Plate 3
LrgRoom 1
LrgRoom 2
Stadium 1
Stadium 2
LongDly 1
LongDly 2
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Chorus 1
Chorus 2
Chorus 3
Chorus 4
FBChorus
Flanger1
SDelay 1
SDelay 2
SFChorus
BRChorus
DPChorus
Flanger 2
Flanger 3
Flanger 4
SDelay 3
SDelay 4
Display Name
No.
Display Name
No.
Type Name
CHORUS Effect List
REVERB Effect List
Effect List
Chorus 1
Chorus 2
Chorus 3
Chorus 4
Feedback Chorus
Flanger 1
Short Delay 1
Short Delay 2
Soft Chorus
Bright Chorus
Deep Chorus
Flanger 2
Flanger 3
Flanger 4
Short Delay 3
Short Delay 4
Type Name
DSP Effect List
735A-E-131A
04.3.26, 0:12 PM
[12]
[13]
10
09
03
06
06
07
13
16
17
19
18
M05
26
M07
Flanger
[07]
[08]
[09]
[10]
[11]
Chorus
[05]
[06]
Phaser
[00]
[01]
[02]
[03]
[04]
Dynamics Fx
DSP Algorithm
No. ID
Flanger
EnhaFlan
Chorus 1
Chorus 2
Chorus 3
Chorus 4
Enha Cho
Phaser
StPhaser
Equalize
Comp 1
Comp 2
Limiter
Enhancer
Display
Name
Flanger
Enhancer - Flanger
Chorus 1
Chorus 2
Chorus 3
Chorus 4
Enhancer - Chorus
Phaser
Stereo Phaser
Equalizer
Compressor 1
Compressor 2
Limiter
Enhancer Phaser
DSP Name
Settable parameters depend on the DSP type. Also,
the parameters for each DSP type depend on the
algorithm* associated with the DSP type. See the DSP
Algorithm List on page A-19 for more information.
* Effector structure and operation type
Appendix
A-17
Display
Name
WK3000_e_A-17-18.p65
18
[34]
[35]
[36]
[37]
[38]
[39]
[40]
[41]
[42]
[43]
Reverb
27
27
27
27
27
27
23
23
24
24
M02
M02
M04
M04
M00
M00
M01
M01
M19
M18
M23
M08
M03
M03
RvbRoom1
RvbRoom2
RvbRoom3
RvbHall 1
RvbHall 2
RvbPlate
GateRvb 1
GateRvb 2
GateRvb 3
GateRvb 4
PhaCho 1
PhaCho 2
PhaDly 1
PhaDly 2
ChoDly 1
ChoDly 2
ChoDly 3
ChoDly 4
CmpDelay
CmpEnDly
CmpChoRf
Cho Flan
FlanDly 1
FlanDly 2
Reverb Room 1
Reverb Room 2
Reverb Room 3
Reverb Hall 1
Reverb Hall 2
Reverb Plate
Gate Reverb 1
Gate Reverb 2
Gate Reverb 3
Gate Reverb 4
Phaser - Chorus 1
Phaser - Chorus 2
Phaser - Delay 1
Phaser - Delay 2
Chorus - Delay 1
Chorus - Delay 2
Chorus - Delay 3
Chorus - Delay 4
Compressor - Delay
Compressor - Enhancer -Delay
Compressor - Chorus -Reflection
Chorus - Flanger
Flanger - Delay 1
Flanger - Delay 2
04
05
M21
M22
A-18
04.3.26, 0:12 PM
[64]
[65]
[66]
[67]
[68]
[69]
[70]
[71]
08
08
08
08
08
08
M29
M29
Guitar Fx
[60]
[61]
[62]
[63]
Wah Fx
11
11
12
12
M17
M17
M17
M16
M16
M16
[50]
[51]
[52]
[53]
[54]
[55]
[56]
[57]
[58]
[59]
01
M09
00
M10
M10
M20
[20]
[21]
[22]
[23]
[24]
[25]
[26]
[27]
[28]
[29]
[30]
[31]
[32]
[33]
Delay
3-Tap Delay
Stereo Delay
Stereo Cross Delay
Enhancer - Delay
Reflection
Rotary Fx
Delay
3Tap Dly
St Delay
StXDelay
Enha Dly
Reflect
Cho/Flanger/Delay Combination
28
22
20
21
M06
25
Crunch
Ovrdrive
Dist 1
Dist 2
Metal
Fuzz
CrnPhase
Od Phase
LFO Wah
Auto Wah
AWhChDly
LWhChDly
Rotary 1
Rotary 2
Od Rot 1
Od Rot 2
RotRef 1
RotRef 2
RotRef 3
OdRtRef 1
OdRtRef 2
OdRtRef 3
Tremolo
Cho Trem
Auto Pan
PhaAPan 1
PhaAPan 2
PhaChoAP
[44]
[45]
[46]
[47]
[48]
[49]
DSP Algorithm
No. ID
[14]
[15]
[16]
[17]
[18]
[19]
DSP Name
Pan/Tremolo Fx
Display
Name
Delay
DSP Algorithm
No. ID
Crunch
Overdrive
Distortion 1
Distortion 2
Metal
Fuzz
Crunch - Phaser
Overdrive - Phaser
LFO Wah
Auto Wah
Auto Wah - Chorus - Delay
LFO Wah - Chorus - Delay
Rotary 1
Rotary 2
Overdrive - Rotary 1
Overdrive - Rotary 2
Rotary - Reflection 1
Rotary - Reflection 2
Rotary - Reflection 3
Overdrive - Rotary - Reflection 1
Overdrive - Rotary - Reflection 2
Overdrive - Rotary - Reflection 3
Tremolo
Chorus - Tremolo
Auto Pan
Phaser - Auto Pan 1
Phaser - Auto Pan 2
Phaser - Chorus - Auto Pan
DSP Name
[92]
[93]
[94]
[95]
[96]
[97]
[98]
[99]
SFX
14
M12
M13
15
M11
M14
M15
M15
Ring Mod
RgChoDly
RingDist
Lo-Fi
CompLoFi
LoFi Ref
Crn LoFi
DistLoFi
Crn Cho
OdChorus
Dist Cho
MetalCho
DistFlan
Met Flan
CrnDelay
Od Delay
DistDly 1
DistDly 2
MetalDly
Fuzz Dly
CrChoDly
DsChoDly
CmpCrDly
AWhCrDly
AWhOdDly
AWhDsDly
LWhOdDly
LWhDsDly
[72]
[73]
[74]
[75]
[76]
[77]
[78]
[79]
[80]
[81]
[82]
[83]
[84]
[85]
[86]
[87]
[88]
[89]
[90]
[91]
M30
M30
M30
M30
M31
M31
M28
M28
M28
M28
M28
M28
M24
M24
M25
M26
M26
M26
M27
M27
Display
Name
DSP Algorithm
No. ID
Ring Modulator
Ring Modulator - Chorus - Delay
Ring Modulator - Distortion
Lo-Fi
Compressor - Lo-Fi
Lo-Fi - Reflection
Crunch - Lo-Fi
Distortion - Lo-Fi
Crunch - Chorus
Overdrive - Chorus
Distortion - Chorus
Metal - Chorus
Distortion - Flanger
Metal - Flanger
Crunch - Delay
Overdrive - Delay
Distortion - Delay 1
Distortion - Delay 2
Metal - Delay
Fuzz - Delay
Crunch - Chorus - Delay
Distortion - Chorus - Delay
Compressor - Crunch - Delay
Auto Wah - Crunch - Delay
Auto Wah - Overdrive - Delay
Auto Wah - Distortion - Delay
LFO Wah - Overdrive - Delay
LFO Wah - Distortion - Delay
DSP Name
Appendix
735A-E-132A
WK3000_e_A-19-31.p65
19
735A-E-133A
04.3.26, 0:12 PM
3 : High Gain (Range: -12, -11, -10 to 0 to +10, +11, +12)
Adjusts the gain of the high-band equalizer.
2 : High Frequency (Range: 0 (6.0KHz), 1
(8.0KHz), 2 (10KHz))
Adjusts the cutoff frequency of the high-band
equalizer.
1 : Low Gain (Range: -12, -11, -10 to 0 to +10, +11, +12)
Adjusts the gain of the low-band equalizer.
0 : Low Frequency (Range: 0 (200Hz), 1 (400Hz),
2 (800Hz))
Adjusts the cutoff frequency of the low-band
equalizer.
■ Parameters
■ Function
This is a two-band equalizer.
02 : 2BandEQ
1 : Depth (Range: 0 to 127)
Adjusts the tremolo depth.
0 : Rate (Range: 0 to 127)
Adjusts the tremolo rate.
■ Parameters
■ Function
Adjusts volume of input signal in accordance
with an LFO.
01 : Tremolo
1 : Depth (Range: 0 to 127)
Adjusts the panning depth.
0 : Rate (Range: 0 to 127)
Adjusts the panning rate.
3 : LFO Rate (Range: 0 to 127)
Adjusts the rate of the LFO.
2 : Mid Frequency (Range: 0 (1.0KHz), 1 (1.3KHz),
2 (1.6KHz), 3 (2.0KHz), 4 (3.0KHz), 5 (4.0KHz),
6 (6.0KHz), 7 (8.0KHz))
Adjusts the center frequency of the mid-band
equalizer.
■ Function
This is a “wah” effect that can automatically
affect the frequency in accordance with an LFO.
04 : LFO Wah
5 : High Gain (Range: -12, -11, -10 to 0 to +10, +11,
+12)
Adjusts the gain of the high-band equalizer.
4 : High Frequency (Range: 0 (6.0KHz), 1
(8.0KHz), 2 (10KHz))
Adjusts the cutoff frequency of the high-band
equalizer.
3 : Mid Gain (Range: -12, -11, -10 to 0 to +10, +11,
+12)
Adjusts the gain of the mid-band equalizer.
2 : Manual (Range: 0 to 127)
Adjusts the frequency used as the basis for the
wah filter.
1 : Low Gain (Range: -12, -11, -10 to 0 to +10, +11,
+12)
Adjusts the gain of the low-band equalizer.
2 : Manual (Range: 0 to 127)
Adjusts the frequency used as the basis for the
wah filter.
1 : Resonance (Range: 0 to 127)
Adjusts the resonance of the sound.
0 : Input Level (Range: 0 to 127)
Adjusts the input level. The input signal can
become distorted when the level of the sound
being input, the number of chords, or the Resonance value is large. Adjust this parameter to
eliminate such distortion.
■ Parameters
■ Function
This is a “wah” effect that can automatically
affect the frequency in accordance with the
level of the input signal.
05 : Auto Wah
4 : LFO Depth (Range: 0 to 127)
Adjusts the depth of the LFO.
1 : Resonance (Range: 0 to 127)
Adjusts the resonance of the sound.
0 : Input Level (Range: 0 to 127)
Adjusts the input level. The input signal can
become distorted when the level of the sound
being input, the number of chords, or the Resonance value is large. Adjust this parameter to
eliminate such distortion.
■ Parameters
0 : Low Frequency (Range: 0 (200Hz), 1 (400Hz),
2 (800Hz))
Adjusts the cutoff frequency of the low-band
equalizer.
■ Parameters
■ Function
This is a three-band equalizer.
■ Function
Continually performs left-right panning of the
input signal in accordance with an LFO.
■ Parameters
03 : 3BandEQ
00 : Auto Pan
DSP Algorithm List
Appendix
A-19
WK3000_e_A-19-31.p65
20
2 : Release (Range: 0 to 127)
Adjusts the time from the point when the input signal drops below a certain level until the
compression operation is stopped.
When an attack feeling is desired (no compression at the onset of the sound), set this parameter to as low a value as possible.
To have compression applied at all times, set a
high value.
1 : Attack (Range: 0 to 127)
Adjusts the attack amount of the input signal.
A smaller value causes prompt compressor
operation, which suppresses the attack of the
input signal.
A larger values delays compressor operation,
which causes attack to be output as-is.
0 : Depth (Range: 0 to 127)
Adjusts compression of the audio signal.
■ Parameters
■ Function
Compresses the input signal, which can have
the effect of suppressing level variation and
making it possible to sustain dampened
sounds longer.
06 : Compressor
3 : Depth(Range: -64 to 0 to +63)
Adjusts the depth of the wah in accordance
with the level of the input signal.
Setting a positive value causes the wah filter
to open in direct proportion with the size of
the input signal, producing a bright sound.
Setting a negative value causes the Wah filter
to close in accordance with the size of the input signal, which produces a dark tone quality. However, large input re-opens the Wah filter, even if it is closed.
A-20
04.3.26, 0:12 PM
0 : Gain (Range: 0 to 127)
Adjusts the input gain.
■ Parameters
■ Function
This effect provides
AmpSimulator.
08 : Distortion
Distortion
+
1 : Manual (Range: -64 to 0 to +63)
Adjusts the phaser shift volume, which is used
for reference.
0 : Resonance (Range: 0 to 127)
Adjusts the resonance of the sound.
■ Parameters
■ Function
This is a monaural phaser that modulates the
phase in accordance with a sine wave LFO.
10 : Phaser
4 : Wet Level (Range: 0 to 127)
Adjusts the volume level of the effect.
3 : Depth (Range: 0 to 127)
Adjusts the depth of the LFO.
2 : Rate (Range: 0 to 127)
Adjusts the rate of the LFO.
1 : Manual (Range: -64 to 0 to +63)
Adjusts the phaser shift volume, which is used
for reference.
2 : Release (Range: 0 to 127)
Adjusts the time from when the input signal
drops below a certain level until the limit operation stops.
3 : Level (Range: 0 to 127)
Adjusts the level being output.
The output volume changes in accordance with
the Limit setting and the characteristics of the
input tone. Use this parameter to correct for
such changes.
0 : Resonance (Range: 0 to 127)
Adjusts the resonance of the sound.
■ Parameters
■ Function
This is a stereo phaser that modulates the phase
in accordance with a sine wave LFO.
09 : Stereo Phaser
3 : Level (Range: 0 to 127)
Adjusts the output level.
2 : High (Range: 0 to 127)
Adjusts the high-band gain.
The cutoff frequency differs according to the
preset DSP.
1 : Low (Range: 0 to 127)
Adjusts the low-band gain.
The cutoff frequency differs according to the
preset DSP.
1 : Attack (Range: 0 to 127)
Adjusts the attack amount of the input signal.
0 : Limit (Range: 0 to 127)
Adjusts the volume level from which the limit
is applied.
■ Parameters
■ Function
This is an effector that you can use to set an
upper limit value on the level of the input signal.
07 : Limiter
3 : Level (Range: 0 to 127)
Adjusts the output level.
The output volume changes in accordance with
the Depth setting and the characteristics of the
input tone. Use this parameter to correct for
such changes.
Appendix
735A-E-134A
WK3000_e_A-19-31.p65
21
735A-E-135A
04.3.26, 0:12 PM
1 : Overdrive Level (Range: 0 to 127)
Adjusts the output level of the overdrive.
0 : Overdrive Gain (Range: 0 to 127)
Adjusts overdrive gain.
■ Parameters
■ Function
This is an overdrive - rotary speaker simulator.
12 : Drive Rotary
5 : Fast Rate (Range: 0 to 127)
Adjusts speaker rotation speed of the fast speed
mode.
4 : Slow Rate (Range: 0 to 127)
Adjusts speaker rotation speed of the slow
speed mode.
3 : Rise Accel (Range: 0 to 127)
Adjusts acceleration when the speed mode is
switched from slow to fast.
2 : Fall Accel (Range: 0 to 127)
Adjusts acceleration when the speed mode is
switched from fast to slow.
1 : Break (Range: Rotate, Stop)
Stops speaker rotation.
0 : Speed (Range: Slow, Fast)
Switches the speed mode between fast and
slow.
■ Parameters
■ Function
This is a rotary speaker simulator.
11 : Rotary
4 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
3 : Depth (Range: 0 to 127)
Adjusts the depth of the LFO.
2 : Rate (Range: 0 to 127)
Adjusts the rate of the LFO.
■ Function
This is a ring modulator (AM modulator) that
makes it possible to modulate the frequency
of internal oscillator (OSC) in accordance with
an internal LFO.
14 : Ring Modulator
3 : High Gain (Range: 0 to 127)
Adjusts the high range enhancer gain.
2 : High Frequency (Range: 0 to 127)
Adjusts the high range enhancer frequency.
1 : Low Gain (Range: 0 to 127)
Adjusts the low range enhancer gain.
0 : Low Frequency (Range: 0 to 127)
Adjusts the low range enhancer frequency.
■ Parameters
■ Function
Enhances the outlines of the low range and
high range of the input signal.
13 : Enhancer
7 : Fast Rate (Range: 0 to 127)
Adjusts speaker rotation speed of the fast speed
mode.
6 : Slow Rate (Range: 0 to 127)
Adjusts speaker rotation speed of the slow
speed mode.
5 : Rise Accel (Range: 0 to 127)
Adjusts acceleration when the speed mode is
switched from slow to fast.
4 : Fall Accel (Range: 0 to 127)
Adjusts acceleration when the speed mode is
switched from fast to slow.
3 : Break (Range: Rotate, Stop)
Stops speaker rotation.
2 : Speed(Range: Slow, Fast)
Switches the speed mode between fast and
slow.
5 : Resonance (Range: 0 to 127)
Adjusts the resonance of the sound.
4 : Tone (Range: 0 to 127)
Adjusts the tone.
3 : Noise Density 2 (Range: 0 to 127)
Adjusts the noise density of Noise Generator
2.
2 : Noise Level 2 (Range: 0 to 127)
Adjusts the level of Noise Generator 2.
1 : Noise Density 1 (Range: 0 to 127)
Adjusts the noise density of Noise Generator
1.
0 : Noise Level 1 (Range: 0 to 127)
Adjusts the level of Noise Generator 1.
■ Parameters
■ Function
This is an effector that reproduces a retro-type
Lo-Fi sound using Noise Generator 1 (phonograph record player type scratch noise generator) and Noise Generator 2 (FM radio type
white noise and pink noise continuous noise
generator), and by noise modulation (amplitude modulation = AM) and distortion of frequency characteristics.
15 : Lo-Fi
4 : Dry Level (Range: 0 to 127)
Adjusts the level of the original sound.
3 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
2 : LFO Depth (Range: 0 to 127)
Adjusts the depth of the LFO.
1 : LFO Rate (Range: 0 to 127)
Adjusts the rate of the LFO.
0 : OSC Frequency (Range: 0 to 127)
Sets the reference frequency of the internal
OSC.
■ Parameters
Appendix
A-21
WK3000_e_A-19-31.p65
22
A-22
04.3.26, 0:12 PM
■ Function
This is 3-phase chorus in accordance with two
LFOs of with different sine wave rates.
18 : 3-Phase Chorus
3 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
2 : Feedback (Range: -64 to 0 to +63)
Adjusts the feedback of the sound.
1 : LFO Depth (Range: 0 to 127)
Adjusts the depth of the LFO.
0 : LFO Rate (Range: 0 to 127)
Adjusts the rate of the LFO.
■ Parameters
■ Function
This is stereo chorus in accordance with a sine
wave LFO.
17 : Sin 2-Phase Chorus
3 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
2 : Feedback (Range: -64 to 0 to +63)
Adjusts the feedback of the sound.
1 : LFO Depth (Range: 0 to 127)
Adjusts the depth of the LFO.
0 : LFO Rate (Range: 0 to 127)
Adjusts the rate of the LFO.
■ Parameters
■ Function
This is monaural chorus in accordance with a
sine wave LFO.
16 : 1-Phase Chorus
7 : Level (Range: 0 to 127)
Adjusts the output level.
6 : Bass(Range: -64 to 0 to +63)
Adjusts the volume of low sounds.
2 : Feedback (Range: 0 to 127)
Adjusts the repeat of the delay.
1 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
0 : Delay Time (Range: 0 to 127)
Adjusts the delay time.
■ Parameters
■ Function
This is delay of stereo input and output.
20 : Stereo Delay 1
3 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
2 : Feedback(Range: -64 to 0 to +63)
Adjusts the feedback of the sound.
1 : LFO Depth (Range: 0 to 127)
Adjusts the depth of the LFO.
0 : LFO Rate (Range: 0 to 127)
Adjusts the rate of the LFO.
■ Parameters
■ Function
This is stereo chorus in accordance with triangular wave LFO.
19 : Tri 2-Phase Chorus
4 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
3 : Depth2 (Slow LFO Depth) (Range: 0 to 127)
Adjusts the depth of LFO2.
2 : Rate2 (Slow LFO Rate) (Range: 0 to 127)
Adjusts the rate of LFO2.
1 : Depth1 (Fast LFO Depth) (Range: 0 to 127)
Adjusts the depth of LFO1.
0 : Rate1 (Fast LFO Rate) (Range: 0 to 127)
Adjusts the rate of LFO1.
■ Parameters
■ Function
This is left/center/right 3-tap delay.
22 : 3-Tap Delay
5 : Ratio R (Range: 0 to 127)
Adjusts the delay time of the right channel.
Proportional to the value set for Delay Time.
4 : Ratio L (Range: 0 to 127)
Adjusts the delay time of the left channel.
Proportional to the value set for Delay Time.
3 : High Damp (Range: 0 to 127)
Adjusts damping of the high-range delay
sound.
The smaller the value, the greater the damping of high-range delay sound.
2 : Feedback (Range: 0 to 127)
Adjusts the repeat of the delay.
1 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
0 : Delay Time (Range: 0 to 127)
Adjusts the delay time.
■ Parameters
■ Function
This is cross feedback delay of stereo input and
output.
21 : Stereo Delay 2
5 : Ratio R (Range: 0 to 127)
Adjusts the delay time of the right channel.
Proportional to the value set for Delay Time.
4 : Ratio L (Range: 0 to 127)
Adjusts the delay time of the left channel.
Proportional to the value set for Delay Time.
3 : High Damp (Range: 0 to 127)
Adjusts damping of the high-range delay
sound.
The smaller the value, the greater the damping of high-range delay sound.
Appendix
735A-E-136A
WK3000_e_A-19-31.p65
23
735A-E-137A
04.3.26, 0:12 PM
2 : Feedback (Range: 0 to 127)
Adjusts the repeat of the reverb.
1 : HPF (Range: 0 to 127)
Adjusts the cutoff frequency of the high-pass
filter.
A larger value cuts the low range.
0 : LPF (Range: 0 to 127)
Adjusts the cutoff frequency of the low-pass
filter.
A smaller value cuts the high range.
■ Parameters
■ Function
This is a fader that creates artificial reverb that
sounds like it is being cut with a gate.
23 : Gate Reverb
6 : Ratio R (Range: 0 to 127)
Adjusts the delay time of the right channel.
Proportional to the value set for Delay Time.
5 : Ratio C (Range: 0 to 127)
Adjusts the delay time of the center channel.
Proportional to the value set for Delay Time.
4 : Ratio L (Range: 0 to 127)
Adjusts the delay time of the left channel.
Proportional to the value set for Delay Time.
3 : High Damp (Range: 0 to 127)
Adjusts damping of the high-range delay
sound.
The smaller the value, the greater the damping of high-range delay sound.
2 : Feedback (Range: 0 to 127)
Adjusts the repeat of the delay.
1 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
0 : Delay Time (Range: 0 to 127)
Adjusts the delay time.
■ Parameters
6 : Dry Level (Range: 0 to 127)
Adjusts the level of the original sound.
5 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
4 : Diffusion (Range: 0 to 127)
Provides fine adjustment of the reverb.
3 : High Damp (Range: 0 to 127)
Adjusts damping of the high-range reverb
sound.
The smaller the value, the greater the damping of high-range reverb sound.
2 : Feedback (Range: 0 to 127)
Adjusts the repeat of the reverb.
1 : HPF (Range: 0 to 127)
Adjusts the cutoff frequency of the high-pass
filter.
A larger value cuts the low range.
0 : LPF (Range: 0 to 127)
Adjusts the cutoff frequency of the low-pass
filter.
A smaller value cuts the high range.
■ Parameters
■ Function
This is gate reverb with a reverse rotation effect.
24 : Reverse Gate Reverb
6 : Dry Level (Range: 0 to 127)
Adjusts the level of the original sound.
5 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
4 : Diffusion (Range: 0 to 127)
Provides fine adjustment of the reverb.
3 : High Damp (Range: 0 to 127)
Adjusts damping of the high-range delay
sound.
The smaller the value, the greater the damping of high-range delay sound.
0 : Tone (Range: 0 to 127)
Adjusts the tone of the reverb sound.
■ Parameters
■ Function
This is an effector that preserves the breadth
of a sound by adding a reverb sound.
27 : Reverb
3 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
2 : Feedback (Range: -64 to 0 to +63)
Adjusts the feedback of the sound.
1 : LFO Depth (Range: 0 to 127)
Adjusts the depth of the LFO.
0 : LFO Rate (Range: 0 to 127)
Adjusts the rate of the LFO.
■ Parameters
■ Function
This is a flanger in accordance with a sine wave
LFO.
26 : Flanger
3 : Tone (Range: 0 to 127)
Adjusts the tone of the reflected sound.
2 : Feedback (Range: 0 to 127)
Adjusts the repeat of the reflected sound.
1 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
0 : Type (Range: 0 to 7)
Selects from among the eight available reflection patterns.
■ Parameters
■ Function
This is an effector that extracts the first reflected
sound from a reverb sound.
25 : Reflection
Appendix
A-23
WK3000_e_A-19-31.p65
24
A-24
04.3.26, 0:12 PM
★ The following “Multi” algorithms are used in combination with the algorithms described above. Parameters are shared by both types of algorithms.
5 : Ratio R (Range: 0 to 127)
Adjusts the delay time of the right channel.
Proportional to the value set for Delay Time.
4 : Ratio L (Range: 0 to 127)
Adjusts the delay time of the left channel.
Proportional to the value set for Delay Time.
3 : High Damp (Range: 0 to 127)
Adjusts damping of the high-range delay
sound.
The smaller the value, the greater the damping of high-range delay sound.
2 : Feedback (Range: 0 to 127)
Adjusts the repeat of the delay.
1 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
0 : Delay Time (Range: 0 to 127)
Adjusts the delay time.
■ Parameters
■ Function
This is left/right 2-tap delay.
28 : 2-Tap Delay
4 : Wet Level (Range: 0 to 127)
Adjusts the level of the effect sound.
3 : ER Level (Range: 0 to 127)
Adjusts the level of the initial reflection.
2 : High Damp (Range: 0 to 127)
Adjusts damping of the high-range reverb
sound.
The smaller the value, the greater the damping of high-range reverb sound.
1 : Time (Range: 0 to 127)
Adjusts the reverb time.
■ Function
This is a multi effector that is related to Phaser
- 3-Phase Chorus.
M02 : Multi02 (Phaser – 3-Phase Chorus)
7 : Delay Feedback
6 : Delay Wet Level
5 : Delay Time
4 : Chorus Wet Level
3 : Chorus Depth 2
2 : Chorus Rate 2
1 : Chorus Depth 1
0 : Chorus Rate 1
■ Parameters
■ Function
This is a multi effector that is related to 3-Phase
Chorus - 3-Tap Delay.
M01 : Multi01 (3-Phase Chorus – 3-Tap Delay)
7 : Delay High Damp
6 : Delay Feedback
5 : Delay Wet Level
4 : Delay Time
3 : Chorus Wet Level
2 : Chorus Feedback
1 : Chorus LFO Depth
0 : Chorus LFO Rate
■ Parameters
■ Function
This is a multi effector that is related to Sin 2Phase Chorus - 2-Tap Delay.
M00 : Multi00 (Sin 2-Phase Chorus – 2-Tap
Delay)
5 : Delay Time
4 : Phaser Wet Level
3 : Phaser Depth
2 : Phaser Rate
1 : Phaser Manual
0 : Phaser Resonance
■ Parameters
■ Function
This is a multi effector that is related to Stereo
Phaser - Stereo Delay 1.
M04 : Multi04 (Stereo Phaser – Stereo Delay
1)
7 : Delay High Damp
6 : Delay Feedback
5 : Delay Wet Level
4 : Delay Time
3 : Flanger Wet Level
2 : Flanger Feedback
1 : Flanger LFO Depth
0 : Flanger LFO Rate
■ Parameters
■ Function
This is a multi effector that is related to Flanger
- 2-Tap Delay.
M03 : Multi03 (Flanger – 2-Tap Delay)
7 : Chorus Depth 2
6 : Chorus Rate 2
5 : Chorus Depth 1
4 : Chorus Rate 1
3 : Phaser Depth
2 : Phaser Rate
1 : Phaser Manual
0 : Phaser Resonance
■ Parameters
Appendix
735A-E-138B
1 : Enhancer Low Gain
7 : Delay Feedback
WK3000_e_A-19-31.p65
7 : Flanger Wet Level
■ Parameters
25
■ Parameters
5 : Chorus LFO Depth
1 : Chorus LFO Depth
7 : Chorus Wet Level
■ Parameters
735A-E-139A
04.3.26, 0:12 PM
■ Parameters
■ Function
This is a multi effector related to Enhancer Flanger.
M07 : Multi07 (Enhancer – Flanger)
7 : Delay High Damp
6 : Delay Feedback
5 : Delay Wet Level
4 : Delay Time
3 : Enhancer High Gain
2 : Enhancer High Frequency
1 : Enhancer Low Gain
0 : Enhancer Low Frequency
6 : Flanger Feedback
7 : Flanger Wet Level
■ Function
This is a multi effector that is related to Enhancer - 2-Tap Delay.
5 : Tremolo Depth
4 : Tremolo Rate
3 : Chorus Wet Level
2 : Chorus Feedback
1 : Chorus LFO Depth
0 : Chorus LFO Rate
■ Parameters
■ Function
This is a multi effector that is related to Sin 2Phase Chorus - Tremolo.
M09 : Multi09
(Sin 2-Phase Chorus – Tremolo)
5 : Flanger LFO Depth
3 : Chorus Wet Level
4 : Flanger LFO Rate
M06 : Multi06 (Enhancer – 2-Tap Delay)
2 : Chorus Feedback
0 : Chorus LFO Rate
6 : Chorus Feedback
4 : Chorus LFO Rate
3 : Enhancer High Gain
■ Function
This is a multi effector that is related to Sin 2Phase Chorus - Flanger.
M08: Multi08 (Sin 2-Phase Chorus – Flanger)
2 : Enhancer High Frequency
1 : Enhancer Low Gain
0 : Enhancer Low Frequency
6 : Flanger Feedback
■ Function
This is a multi effector related to Enhancer - 1Phase Chorus.
5 : Flanger LFO Depth
3 : Enhancer High Gain
4 : Flanger LFO Rate
M05 : Multi05 (Enhancer – 1-Phase Chorus)
2 : Enhancer High Frequency
0 : Enhancer Low Frequency
6 : Delay Wet Level
2 : Ring LFO Depth
1 : Ring LFO Rate
0 : Ring OSC Frequency
■ Parameters
■ Function
This is a multi effector that is related to Ring
Modulator - Sin 2-Phase Chorus.
M12 : Multi12 (Ring Modulator – Sin 2-Phase
Chorus - 2-Tap Delay)
7 : Lo-Fi Bass
6 : Lo-Fi Resonance
5 : Lo-Fi Tone
4 : Lo-Fi Noise 2
3 : Lo-Fi Noise 1
2 : Compressor Level
1 : Compressor Attack
0 : Compressor Depth
■ Parameters
■ Function
This is a multi effector related to Compressor Lo-Fi.
M11 : Multi11 (Compressor – Lo-Fi)
6 : Auto Pan Depth
5 : Auto Pan Rate
4 : Phaser Wet Level
3 : Phaser Depth
2 : Phaser Rate
1 : Phaser Manual
0 : Phaser Resonance
■ Parameters
■ Function
This is a multi effector that is related to Stereo
Phaser - Auto Pan.
M10 : Multi10 (Stereo Phaser – Auto Pan)
Appendix
A-25
WK3000_e_A-19-31.p65
26
Multi14 (Lo-Fi – Reflection)
A-26
04.3.26, 0:12 PM
7 : Reflection Tone
6 : Reflection Feedback
5 : Reflection Wet Level
4 : Reflection Type
3 : Lo-Fi Resonance
2 : Lo-Fi Tone
1 : Lo-Fi Noise2
0 : Lo-Fi Noise1
■ Parameters
■ Function
This is a multi effector related to Lo-Fi - Reflection.
M14 :
7 : Distortion Level
6 : Distortion Tone
5 : Distortion Gain
4 : Ring Dry Level
3 : Ring Wet Level
2 : Ring LFO Depth
1 : Ring LFO Rate
0 : Ring OSC Frequency
■ Parameters
■ Function
This is a multi effector related to Ring Modulator - Distortion.
M13 : Multi13 (Ring Modulator – Distortion)
7 : Delay Wet Level
6 : Delay Time
5 : Chorus LFO Depth
4 : Ring Dry Level
3 : Ring Wet Level
2 : Rotary Slow Rate
1 : Rotary Break
0 : Rotary Speed
■ Parameters
■ Function
This is a multi effector related to Rotary - Reflection.
M17 : Multi17 (Rotary – Reflection)
7 : Reflection Tone
6 : Reflection Feedback
5 : Reflection Wet Level
4 : Drive Rotary Fast Rate
3 : Drive Rotary Slow Rate
2 : Drive Rotary Speed
1 : Drive Rotary Level
0 : Drive Rotary Gain
■ Parameters
■ Function
This is a multi effector related to Drive Rotary
- Reflection.
M16 : Multi16 (Drive Rotary – Reflection)
7 : Lo-Fi Resonance
6 : Lo-Fi Tone
5 : Lo-Fi Noise2
4 : Lo-Fi Noise1
3 : Distortion Level
2 : Distortion High
1 : Distortion Low
0 : Distortion Gain
■ Parameters
■ Function
This is a multi effector related to Distortion Lo-Fi.
M15 : Multi15 (Distortion – Lo-Fi)
7 : Delay High Damp
6 : Delay Feedback
5 : Delay Wet Level
4 : Delay Time
3 : Compressor Level
2 : Compressor Release
1 : Compressor Attack
0 : Compressor Depth
■ Parameters
■ Function
This is a multi effector related to Compressor Stereo Delay 1.
M19 : Multi19 (Compressor – Stereo Delay
1)
7 : Delay Feedback
6 : Delay Wet Level
5 : Delay Time
4 : Enhancer High Gain
3 : Enhancer Low Gain
2 : Compressor Level
1 : Compressor Attack
0 : Compressor Depth
■ Parameters
■ Function
This is a multi effector that is related to Compressor - Enhancer - 2-Tap Delay.
M18 : Multi18 (Compressor – Enhancer - 2Tap Delay)
6 : Reflection Tone
5 : Reflection Feedback
4 : Reflection Wet Level
3 : Rotary Fast Rate
Appendix
735A-E-140A
WK3000_e_A-19-31.p65
27
735A-E-141A
04.3.26, 0:12 PM
■ Function
This is a multi effector that is related to LFO
Wah - Tri 2-Phase Chorus - 2-Tap Delay.
M22 : Multi22 (LFO Wah – Tri 2-Phase Chorus – 2-Tap Delay)
7 : Delay Feedback
6 : Delay Wet Level
5 : Delay Time
4 : Chorus LFO Depth
3 : Chorus LFO Rate
2 : Wah Depth
1 : Wah Manual
0 : Wah Resonance
■ Parameters
■ Function
This is a multi effector that is related to Auto
Wah - Tri 2-Phase Chorus - 2-Tap Delay.
M21 : Multi21 (Auto Wah – Tri 2-Phase Chorus – 2-Tap Delay)
7 : Auto Pan Depth
6 : Auto Pan Rate
5 : Chorus LFO Depth
4 : Chorus LFO Rate
3 : Phaser Depth
2 : Phaser Rate
1 : Phaser Manual
0 : Phaser Resonance
■ Parameters
■ Function
This is a multi effector that is related to Phaser
- 1-Phase Chorus - Auto Pan.
M20 : Multi20 (Phaser – 1-Phase Chorus –
Auto Pan)
6 : Delay Wet Level
■ Parameters
7 : Reflection Tone
6 : Delay Wet Level
5 : Delay Time
4 : Chorus LFO Depth
3 : Distortion Level
2 : Distortion High
1 : Distortion Low
0 : Distortion Gain
■ Parameters
7 : Delay Feedback
4 : Distortion Level
5 : Delay Time
3 : Distortion Tone
2 : Distortion Gain
1 : Wah Depth
■ Function
This is a multi effector that is related to Distortion - 1-Phase Chorus - 2-Tap Delay.
M24 : Multi24 (Distortion – 1-Phase Chorus
– 2-Tap Delay)
6 : Reflection Feedback
0 : Wah Manual
■ Function
This is a multi effector that is related to Auto
Wah - Distortion - 2-Tap Delay.
4 : Chorus LFO Depth
5 : Reflection Wet Level
3 : Chorus LFO Rate
M26 : Multi26 (Auto Wah – Distortion – 2-Tap
Delay)
7 : Delay Feedback
2 : Compressor Level
1 : Compressor Attack
0 : Compressor Depth
■ Parameters
4 : Distortion Level
5 : Delay Time
3 : Distortion High
2 : Distortion Low
1 : Distortion Gain
■ Function
This is a multi effector that is related to Compressor - Sin 2-Phase Chorus - Reflection.
M23 : Multi23 (Compressor – Sin 2-Phase
Chorus – Reflection)
6 : Delay Wet Level
0 : Compressor Depth
■ Parameters
7 : Delay Feedback
5 : Delay Time
■ Function
This is a multi effector that is related to Compressor - Distortion - 2-Tap Delay.
M25 : Multi25 (Compressor – Distortion – 2Tap Delay)
7 : Delay Feedback
6 : Delay Wet Level
4 : Chorus LFO Depth
3 : Wah LFO Depth
2 : Wah LFO Rate
1 : Wah Manual
0 : Wah Resonance
■ Parameters
Appendix
A-27
WK3000_e_A-19-31.p65
28
A-28
04.3.26, 0:12 PM
1 : Distortion Low
0 : Distortion Gain
■ Parameters
■ Function
This is a multi effector related to Distortion Phaser.
M29 : Multi29 (Distortion – Phaser)
7 : Delay High Damp
6 : Delay Feedback
5 : Delay Wet Level
4 : Delay Time
3 : Distortion Level
2 : Distortion High
1 : Distortion Low
0 : Distortion Gain
■ Parameters
■ Function
This is a multi effector that is related to Distortion - 3-Tap Delay.
M28 : Multi28 (Distortion – 3-Tap Delay)
7 : Delay Feedback
6 : Delay Wet Level
5 : Delay Time
4 : Distortion Level
3 : Distortion Gain
2 : Wah LFO Depth
1 : Wah LFO Rate
0 : Wah Manual
■ Parameters
■ Function
This is a multi effector that is related to LFO
Wah - Distortion - 2-Tap Delay.
M27 : Multi27 (LFO Wah – Distortion – 2-Tap
Delay)
7 : Flanger Wet Level
6 : Flanger Feedback
5 : Flanger LFO Depth
4 : Flanger LFO Rate
3 : Distortion Level
2 : Distortion High
1 : Distortion Low
0 : Distortion Gain
■ Parameters
■ Function
This is a multi effector related to Distortion Flanger.
M31 : Multi31 (Distortion – Flanger)
7 : Chorus Wet Level
6 : Chorus Feedback
5 : Chorus LFO Depth
4 : Chorus LFO Rate
3 : Distortion Level
2 : Distortion High
1 : Distortion Low
0 : Distortion Gain
■ Parameters
■ Function
This is a multi effector that is related to Distortion - Sin 2-Phase Chorus.
M30 : Multi30 (Distortion – Sin 2-Phase Chorus)
7 : Phaser Depth
6 : Phaser Rate
5 : Phaser Manual
4 : Phaser Resonance
3 : Distortion Level
2 : Distortion High
Appendix
735A-E-142A
735A-E-143A
WK3000_e_A-19-31.p65
29
04.3.26, 0:12 PM
735A-E-144A
WK3000_e_A-19-31.p65
30
04.3.26, 0:12 PM
735A-E-145A
WK3000_e_A-19-31.p65
31
04.3.26, 0:12 PM
735A-E-146C
WK3100_e_MIDI Chart.p65
2
04.3.26, 0:12 PM
Key's
Ch's
After
Touch
Control
Change
Pitch Bender
Note ON
Note OFF
Velocity
True voice
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X*2
O
O
O
O
O*3
O*3
O*3
O
O
O
O
0,32
1
6,38
7
10
11
16
17
18
19
64
66
67
71
72
73
74
X
O
O 9nH v = 1-127
X
0-127
0-127*1
O
X
X
O 9nH v = 1-127
X 9nH v = 0
0-127
❊❊❊❊❊❊❊❊❊❊❊❊❊❊
Mode 3
X
❊❊❊❊❊❊❊❊❊❊❊❊❊❊
Mode 3
X
❊❊❊❊❊❊❊❊❊❊❊❊❊❊
Default
Messages
Altered
Mode
Note
Number:
1-16
1-16
Recognized
1-16
1-16
Transmitted
Default
Changed
Basic
Channel
Function ..
MIDI Implementation Chart
Models WK-3500/WK-3100/WK-3000
Brightness
Bank select
Modulation
Data entry
Volume
Pan
Expression
DSP Parameter0
DSP Parameter1
DSP Parameter2
DSP Parameter3
Hold1
Sostenuto
Soft pedal
Resonance
Release Time
Attack Time
*1 Depends on tone.
Remarks
Version: 1.0
735A-E-147A
WK3100_e_MIDI Chart.p65
3
04.3.26, 0:12 PM
: Local ON/OFF
: All notes OFF
: Active Sense
: Reset
Aux
X
X
X
X
X
O
O
X
X
X
X
X
X
O
O 0-127
❊❊❊❊❊❊❊❊❊❊❊❊❊❊
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Brightness
Vibrato rate
Vibrato depth
Vibrato delay
DSP Parameter4
DSP Parameter5
DSP Parameter6
DSP Parameter7
Reverb send
Chorus send
NRPN LSB, MSB
RPN LSB, MSB
All sound off
Reset all controller
Release Time
Attack Time
Mode 2 : OMNI ON, MONO
Mode 4 : OMNI OFF, MONO
*3 Selected in accordance with sustain pedal setting.
Song Memory functions.
O : Yes
X : No
*2 Cannot be sent by keyboard play or control panel operations on this instrument, but sent by Auto Accompaniment or
Mode 1 : OMNI ON, POLY
Mode 3 : OMNI OFF, POLY
Remarks
Messages
: Clock
: Commands
System
Real Time
O
O
X
X
X
: Song Pos
: Song Sel
: Tune
System
Common
O 0-127
❊❊❊❊❊❊❊❊❊❊❊❊❊❊
O
:True #
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
System Exclusive
Program
Change
74
76
77
78
80
81
82
83
91
93
98, 99
100, 101
120
120
72
73
This recycle mark indicates that the packaging conforms to
the environmental protection legislation in Germany.
CASIO COMPUTER CO.,LTD.
6-2, Hon-machi 1-chome
Shibuya-ku, Tokyo 151-8543, Japan
WK3100_e_cover.p65
2
F
04.3.26, 0:13 PM
MA0403-C Printed in China
WK3100-E-1
Download PDF

advertising