Installation

Instructions

If you have questions, call 800-GE-CARES or visit our website at: www.monogram.com

27" and 30"

Warming Drawers

Models:

ZKD910

ZTD910

Monogram.

We bring good things to life.

®

Contents

Before you begin — Read these instructions completely and carefully.

IMPORTANT - Save these instructions for local inspector’s use.

IMPORTANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES.

Note to Installer - Be sure to leave these instructions with the Consumer.

Note to Consumer - Keep these instructions with your Owner’s Manual for future reference.

This appliance must be properly grounded. See “Electrical Supply”, page 4.

Cet appareil doit être correctement mis à la terre. Consulter page 4.

If you received a damaged warming drawer, you should immediately contact your dealer or builder.

Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE

Appliance Warranty. See the Use & Care

Guide for warranty information.

• Use this appliance only for its intended purpose.

Check with local utilities for electrical codes that apply in your area. Local codes vary.

Installation electrical connections and grounding must comply with applicable codes.

In the absence of local codes, the drawer should be installed in accordance with

National Electrical Code ANSI/NFPA 70-1990 or latest edition.

WARNING:

ANTI-TIP PRECAUTIONS

An anti-tip brace must be installed to prevent the drawer from tipping forward when opened and loaded. Failure to do so could result in personal injury.

PRÉCAUTIONS

CONTRE LE BASCULEMENT

Pour éviter les blessures, il faut installer une patte de retenue pour empêcher le tiroir de basculer quand il est ouvert et plein.

For Monogram local service in your area,

1-800-444-1845.

For Monogram service in Canada, call

1-888-880-3030.

For Monogram Parts and Accessories, call

1-800-626-2002.

Design Information

Models Available .................................................................................................................................. 3

Product Dimensions ............................................................................................................................ 3

Accessories ........................................................................................................................................... 3

Tools and Materials Required ............................................................................................................ 3

Installation Preparation

Advance Planning ............................................................................................................................... 4

Grounding the Appliance ................................................................................................................... 4

Remove the Packaging and Parts ....................................................................................................... 5

Installation Below a Countertop ........................................................................................................ 5

Installation Below Wall Ovens ............................................................................................................ 6

Installation

Step 1: Provide Cabinet Support and Anti-Tip Bracket ................................................................... 7

Step 2: Install Warming Drawer ......................................................................................................... 7

2

Models

Available

ZTD910

30” Wide model

ZKD910

27” Wide model

Design Information

Warming Drawer

The warming drawers may be installed directly into a wall or wall oven cabinetry, or below a countertop.

Product

Dimensions

Accessories

27"

Drawer

Open

1"

23-1/4"

9"

10-1/2"

26"

Including

Handle

A

Dimension A

ZTD910 30”

ZKD910 26-3/4”

ZXD27B, ZXD30B – This kit provides for the installation of a custom front panel on 27” and 30" black and white wide models.

Note: The original drawer front will be removed and discarded when this kit is used. The tubular handle can be reinstalled onto the custom panel with longer screws (not provided). Or, the original handle can be replaced with a custom handle of your choice.

(Handle is not supplied.) Choose a custom handle to match or complement cabinetry hardware.

JXPN1 – Warming drawer pan kit. This kit includes supports and a set of 5 pans which fit into 27" and 30" models.

JXPN2 – Warming drawer pan kit. This kit includes supports and a set of 3 pans which fit into 27" and 30" models.

Tools and

Materials

Required

• Wood screws and adhesive or other hardware for installing runners or shelf to support warmer drawer.

• 2 x 4 or 2 x 2 lumber for runners

• 2 x 4 or 2 x 2 wood block for anti-tip security

• Saw

• Level

• Drill and 1/16” bit

• Phillips screwdriver

Runners must be level, rigidly mounted and capable of supporting

150 pounds.

3

Advance

Planning

Grounding the

Appliance

Design Information

Warming Drawer

• The drawer may be installed below a countertop, a cooktop, a single or double oven and side by side using 2 drawers.

• The warming drawer can be installed below approved cooktops. Allow 2" min. clearance from bottom of cooktop burner box to top of warming drawer cutout. See page 5.

• The warming drawer can be installed below approved ovens. Allow a 2" min. clearance between cutouts. Additional clearances may be required. See page 6.

• Electrical power cord is located on the right side of the warming oven. Locate the outlet within reach of the 56” long power cord in an adjacent cabinet, within 42” of the right side or 16” from the left side of the cutout. A recessed receptacle can be installed on the right side of the cutout, 7” max. from the rear of cabinet.

IMPORTANT - (Please read carefully)

FOR PERSONAL SAFETY, THIS APPLIANCE

MUST BE PROPERLY GROUNDED.

Do not use an extension cord or adapter plug with this appliance. Follow National electrical codes or prevailing local codes and ordinances.

Recessed

Receptacle 7"

Max. From Rear on Right Side.

Drill 1-1/2" Hole

For Power Cord For

Left or Right Side

Outlet Location

This warming drawer must be supplied with

120V, 60Hz, and connected to an individual, properly grounded branch circuit, and protected by a 15 or 20 amp circuit breaker or time delay fuse.

• A properly grounded 3-prong receptacle should be located within reach of the drawers’ 56” long power cord.

• Locate the receptacle in an adjacent cabinet.

– within 42” of the right side or,

– within 16” of the left side or,

– A recessed receptacle may be located on the right side of the cutout, 7” from the back of the cabinet. In this location, the excess power cord should be coiled and secured to the warming drawer side with the power cord clip.

• When two warming drawers are installed side to side, they can operate from the same receptacle.

IMPORTANT: (Please read carefully).

The power cord of this appliance is equipped with a three-prong (grounding) plug that mates with a standard three-prong grounding wall receptacle to minimize the possibility of electric shock. The customer should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded and has the correct polarity.

• Where a standard two-prong wall receptacle is encountered, it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded threeprong wall receptacle.

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

DO NOT USE AN EXTENSION CORD.

4

Remove

Packaging and Parts

Installation

Below a

Countertop

Installation Preparation

Warming Drawer

• Place carton on a flat surface.

• Open one end of the carton and lift off the top piece.

• Lift the warmer up and out of the carton.

• Place the drawer on top of the shipping carton to protect the drawer front and the finished flooring.

• Remove all packing materials and tape.

• Locate package containing 4 wood screws and set aside.

Parts provided:

• 4 Wood Screws

Electrical

Outlet 16" Max.

From Left Side.

Install

2x4 or 2x2

Anti-Tip Block

Against Rear

Cabinet Wall

9" From Floor to Bottom of Block

9"

Electrical Outlet

Flush With Side

Electrical Outlet 42" Max.

From Right Side.

of Cabinet 7" Max.

7"

Install a Solid Barrier

Below a Cooktop

See Note

25"

1-1/2" Cabinet Top

1" Min.*

9-1/4"

36"

Countertop

Height

A

23-1/2" Min.

1/4"

Air Gap

Solid Barrier

Install a Solid Barrier and a 1/4" Air Gap

Above Warming Drawer

Dim. A

ZKD30 28-1/2”

ZKD27 25-1/2”

*Note: When installing the warming drawer below a cooktop, a solid barrier must be installed at least 1" from the lowest point of the bottom of cooktop burner box to the top of cutout. Use any solid material such as 1/4" thick plywood.

Allow at least 1/4" air gap between the barrier and the top of the warming drawer. See label on top of the warming drawer for approved cooktop models.

• When installed, the front face of the drawer will be nearly flush with adjacent cabinetry doors.

• Drawer overlaps will conceal cut edges on all sides of the opening.

The rough opening for the drawer must be:

– Depth - 23-1/2” min. from inside back to front of cabinet frame.

– Width - 25-1/2” for 27” wide models,

28-1/2” for 30” wide models.

– Height - 9-1/4”.

• 5” min. above floor or 1” above toekick.

23-1/4” from floor to bottom of cutout is recommended for under countertop installation.

Installation below a cooktop:

Warming drawers are approved for installation below only certain specified cooktop models. See the label attached to the top of the warming drawer for approved models. A solid barrier and air gap between cooktop and warming drawer is required. See Note above.

Installation below a cabinet drawer:

The warming drawer may be installed beneath a cabinet drawer. In this installation, a solid barrier should be installed above the warming drawer to block access. Use any solid material such as 1/4" thick plywood. Allow at least 1/4" air gap between the barrier and the top of the warming drawer. Observe the 5" min. above the floor or 1" above the toekick minimum installation height.

Note: If you are installing in frameless cabinets, it may be necessary to install 1/2” wide cleats to accept drawer mounting screws. See drawer to find exact locations of mounting screws.

Side to Side Installation:

Install two warming drawers in separate cutouts.

Allow 2" min. between cutouts.

2"

Min.

Side to Side Installation

5

Installation

Below

Wall Ovens

INSTALLATION

BELOW A

SINGLE OVEN

INSTALLATION

BELOW A

DOUBLE OVEN

23-1/2" Min.

Inside

Design Information

Warming Drawer

Note: Additional clearance between cutouts may be required. Check to be sure that oven supports above the

Warming Drawer location does not obstruct the required interior 23-1/2” depth and 9-1/4” height.

2x2 or 2x4

Anti-Tip Block

Against Rear

Wall, 9" From

Floor to

Bottom of

Block

9"

9-1/4"

Oven

Cutout

2" Min.

Allow 5/8"

Overlap on

All Sides 23-1/4"

10-1/2"

A

1" Min. Above Toekick or Adjust to Oven Installation Height

23-1/2" Min.

Inside

B

ZKD30

ZKD27

Dim. A

28-1/2”

25-1/2”

Dim. B

30”

26-3/4”

9"

9-1/4"

Oven

Cutout

Allow 5/8"

Overlap on

All Sides

Note: Additional clearance between cutouts may be required. Check to be sure that oven supports above the

Warming Drawer location does not obstruct the required interior 23-1/2” depth and 9-1/4” height.

2x2 or 2x4

Anti-Tip Block

Against Rear

Wall, 9" From

Floor to

Bottom of

Block

2" Min.

23-1/4"

10-1/2"

A

1" Min. Above Toekick B

When installed under a wall oven:

Warming drawers are approved for installation below only certain specified wall oven models.

See the label attached to the top of the warming drawer for approved models.

• When installed, the front face of the drawer will be nearly flush with adjacent cabinetry doors.

• Drawer overlaps will conceal cut edges on all sides of the opening.

The rough opening for the drawer must be:

– Depth – 23-1/2” min. from inside back to front of cabinet frame.

– Width – 25-1/2” for 27” wide models,

28-1/2” for 30” wide models.

– Height - 9-1/4”.

– Allow 2” min. between oven and drawer cutouts for clearance of overlaps.

Note: If you are installing in frameless cabinets, it may be necessary to install 1/2” wide cleats to accept drawer mounting screws. See drawer for mounting screw locations.

6

Provide

Cabinet

Support

Step 1

Install

Anti-Tip

Brackets

Step 2

Install

Warming

Drawer

2"x 4" or

Equivalent Runners

Installation

Warming Drawer

2"x 4" or

Equivalent Runners

23-1/2" 23-1/2"

22"

27"

Important: When installed below a single or double oven, check to be sure that any oven supports above the cutout do not obstruct the 23-1/2” required depth of the warming drawer cutout.

• A 2” min. clearance between oven and warming drawer cutouts are required.

Additional clearance may be required if 2 x 4 blocks are used to support runners or solid floor of the oven above.

• The warmer drawer may be supported by either a solid bottom, 2 x 4 or 2 x 2 runners.

25"

30"

• The support must be level and rigidly mounted, flush with the bottom edge of the cutout.

– There is no way to level the drawer once it has been installed. Be sure supports are level.

• The entire weight of the drawer is supported by the runners or solid floor and must be capable of supporting 150 lbs.

WARNING:

ANTI-TIP PRECAUTIONS

An anti-tip brace must be installed to prevent the drawer from tipping forward when opened and loaded. Failure to do so could result in personal injury.

PRÉCAUTIONS

CONTRE LE BASCULEMENT

Pour éviter les blessures, il faut installer une patte de retenue pour empêcher le tiroir de basculer quand il est ouvert et plein.

9"

2x4 or 2x2

Runners or Solid

Bottom

Install

2x4 or 2x2

Anti-Tip Block

Against Rear

Cabinet Wall

9" From Floor to Bottom of Block

• Slide left corner of the drawer into the opening.

• Push power cord into the hole leading to the outlet location. Thread the cord through as drawer is being pushed back into the opening. Check to be sure power cord does not get trapped under the drawer.

– If the outlet is installed inside the opening, plug the cord into the outlet. Coil power cord and secure to warming drawer side with power cord clip.

• Push the drawer back until the front flange is flush to the cabinet front.

• Open the drawer fully.

• Drill pilot holes through the holes in the overlaping frame, one on each corner.

• Drive wood screws provided into each corner.

7

Pub. No. 49-8937-1

Dwg. No. 164D3333P167

(N.D. 584) 9/02

977-0160-001-Rev. 1

Note: While performing installations described in this book, safety glasses or goggles should be worn.

For Monogram ® local service in your area, call

1-800-444-1845.

Note: Product improvement is a continuing endeavor at

General Electric. Therefore, materials, appearance and specifications are subject to change without notice.

Monogram.

We bring good things to life.

®

General Electric Company

Louisville, KY 40225