Features: Back, Ports, And Battery Charge Well
Contents of the box:
This Guide
NEO compartment
Docking connector
Desktop
1
PX3001
Docking
3
Getting Started
Insert the NEO to charge its battery.
Choose a plug for the universal power adaptor. The
adaptor may already be fi: tted with the plug you need.
Slide the NEO into the Docking
Station until it latches.
Station
Quick Star
t Guide
ber 14,
2008
Novem
Drain hole
PN: 81001
76.A
ISO 9001
Certified
Quality
Manage
ment System
The Docking Station
Power adaptor
and plugs
USB Micro-AB to A cable
Spare battery well
Drain hole
Battery contacts
Spare battery well
Micro-USB connector
Mounting The Desktop Docking Station
NEO compartment
The Desktop Docking Station can be
fixed to the optional Wall Mount Bracket
(model PX3011), or to another surface,
by two broad-headed screws.
Rubber feet (quantity 4)
LED indicator
Mounting holes (quantity 2)
Mounting screw (quantity 2)
Docking connector
Note: Use only the universal
AC power supply approved by
Psion Teklogix for use with the
Docking Station.
2. Pivot the existing plug
out of the adaptor.
DC In port
Features: Front
1. Press the button on
the power adaptor to
release the plug.
3. Pivot the desired plug into
the adaptor until it clicks.
2
Connect the Docking Station
to external power.
Note: The position of
the mounting holes is
indicated by markings on
the front and sides of the
Desktop Docking Station.
Insert the screws into the holes on the base of the unit,
then slide the unit towards the back to secure it.
.
4
Insert the spare battery.
Note: During charge, the LED indicator on the NEO
is YELLOW until charging reaches 75%.
Between 75% and 95% the indicator flashes
GREEN slowly, and, above 95%, the indicator is
GREEN continuously.
The LED indicator on the Docking Station behaves
the same when a spare battery is being charged.
Allow the NEO and the spare battery to charge
for three hours before first use.
DC Input
Note: Full battery performance is only reached after
the first few charge/discharge cycles.
0 - 40 °C
32 - 104 °F
3h
Over
To connect the Docking Station to a host computer:
™
Location Guide For Mounting Screws
The NEO in the Docking Station acts as a USB Client.
1. Connect the smaller end
of the USB cable to the
Docking Station.
Rubber feet
2.20 in (5.60 cm)
USB Host computer
Maximum diameter of screw head: 1.05 cm (0.41 in)
Maximum diameter of screw shaft: 0.65 cm (0.26 in)
November 14, 2008
2.09 in
(5.30 cm)
Mounting
holes
Maximum height of screw head:
0.45 cm (0.18 in)
Maximum height between screw
head and mounting surface:
0.4 cm (0.16 in)
Quick Start Guide
2.13 in
(5.40 cm)
Dimensions Of Mounting Screws
Desktop Docking Station
0.512 in
(1.30 cm)
5.20 in (13.2 cm)
2. Connect the flat
end of the USB cable
to the host computer.
PX3001
0.512 in Outline of
(1.30 cm) Desktop Docking
Station
Front of Docking
Station
2.16 in (5.50 cm)
0.61 in
(1.55 cm)
3.44 in (8.75 cm)
The mounting screws are M4 x 6mm panhead screws.
Psion Teklogix and NEO
are trademarks of Psion
Teklogix Inc. Other product
names mentioned in this
document are trademarks
or registered trademarks of
other hardware, software,
or service providers and are
used herein for identification
purposes only.
8
1
0
0
1
7
6
8100176
Rev. A
ISO 9001 Certified
Quality Management System
PN: 8100176.A
">
