Peavey 602 Music Mixer Operating Guide

 OPERATING, GUIDE
CMX 602
Mixing Console
7%)
A Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
0 Intended to alert the user to the presence of important operating and maintenance (servicing) instruc-
tions in the literature accompanying the product.
CAUTION Risks of electrical shock — DO NOT OPEN
CAUTION To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside. Refer
Servicing to qualified service personnel.
WARNING To prevent electrical shock or fire hazard, do not expose this appliance to rain or moisture, Before
using this appliance, read the operating guide for further warnings.
sobre la operación y mantenimiento en la literatura que viene con el producto.
Este símbolo tiene el propósito de alertar al usuario de la presencia de “(voltaje) peligroso” que no
tiene aislamiento dentro de la caja del producto que puede tener una magnitud suficiente como
para constituir riesgo de corrientazo.
PRECAUCION Riesgo de corrientazo - No abra.
PRECAUCION Para disminuír el riesgo de corrientazo, no abra la cubierta. No hay piezas adentro que el usuario
pueda reparar. Deje todo mantenimiento a los técnicos calificados.
ADVERTENCIA Para evitar corrientazos o peligro de incendio, no deje expuesto a la lluvia o humedad este aparato.
Antes de usar este aparato, lea más advertencias en la guía de operación.
4 Este símbolo tiene el propósito de alertar al usuario de la presencia de instrucciones importantes
sur l’utilisation et 'entretien (service) de l'appareil dans la littérature accompagnant le produit.
Ce symbole est utilisé pour indiquer à l'utilisateur la présence à l’intérieur de ce produit de tension non-
isolée dangereuse pouvant être d'intensité suffisante pour constituer un risque de choc électrique.
ATTENTION Risques de choc électrique — NE PAS OUVRIR!
ATTENTION Afin de réduire le risque de choc électrique, ne pas enlever le couvercle. Il ne se trouve à l’intérieur
aucune pièce pouvant être réparée par l'utilisateur. Confier l’entretien à un personnel qualifié.
AVERTISSEMENT Afin de prévenir les risques de décharge électrique ou de feu, n'exposez pas cet appareil
à la pluie ou à l’humidité. Avant d'utiliser cet appareil, lisez les avertissements supplémentaires situés dans le
guide d'utilisation.
A Ce symbole est utilisé pour indiquer a Vutilisateur qu'il ou qu'elle trouvera d'importantes instructions
4 Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam
machen, die Handhabung und Wartung des Produkts betreffen.
Dieses Symbol soll den Anwender vor unisolierten gefihrlichen Spannungen innerhalb des Gehauses
warnen, die von Ausreichender Stárke sind, um einen elektrischen Schlag verursachen zu kónnen.
VORSICHT Risiko - Elektrischer Schlag! Nicht öffnen!
VORSICHT Um das Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es befinden
sich keine Teile darin, die vom Anwender repariert werden könnten. Reparaturen nur von qualifiziertem Fachper-
sonal durchführen lassen.
ACHTUNG Um einen elektrischen Schlag oder Feuergefahr zu vermeiden, sollte dieses Gerät nicht dem Regen
oder Feuchtigkeit ausgesetzt werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.
ur we 2 i 5 MICUNE 6 — EQUA L IZA TON REZA cue A OUTPUTS ——, = À
o Г] = = e E ER
©: ©: © © 0 0 0::0::0 a O: O: т
= a a : ñ = а i 15+ a ый ñ ах Un
ha ALLE Six CHANNEL MIXER
LEVEL LEVEL LEVEL [EYWEL | + т Ш T АНХ AOE
| | | | | | | 1
1 3 4 5 6 7 8 9 11
Thank you for purchasing the Peavey CMX™ 602. It is a six-channel, easy-to-use, highly mobile mixing console.
Your CMX 602 features a rugged, heavy-gauge, cold-rolled steel chassis, finished in oven-cured epoxy for
toughness and screen-printed utilizing the latest photographic film and UV.-cured ink technology for razor-
sharp, hard-wearing, control I.D. and calibration graphics.
Every on-board component has been carefully chosen to deliver the highest possible performance. Precision,
professional reliability, and absolute minimal operating noise characteristics are among the initial criteria us-
ed during the process of selecting the components that ensure that your CMX 602 becomes an indispensable
addition to your performance equipment.
All printed circuit boards are constructed from rugged U.S. military specification material using the latest
automated assembly technology, wave solder, and computer-controlled ‘All-faults analyzed and corrected” Q.A.
procedures.
Each channel features front panel output controls, as well as group High, Mid, and Low equalization controls.
Clip LED (1)
This LED will illuminate when the signal in the channel reaches clipping.
Level Controls (2)
These determine the levels of the channels in the main mix. These controls should be operated near the mid-
point of travel (#5) to insure that an optimum balance between channel noise and headroom is made available.
Low EQ (3)
An active tone control (shelving type, +15 dB) that varies the low frequency boost or cut.
Mid EQ (4)
An active tone control (peak/notch, +12 dB) that adjusts the mid frequency range.
High EQ (5)
An active tone control (shelving type, +15 dB) that varies the high frequency boost or cut.
LED Bar (6)
A five segment LED array used to visually indicate the level of signal at the Master output. The top (red)
LED is a clip indicator for the Master output.
Meter Adjust (7)
Used to set the level of signal that is seen by the LED meter.
Master Output (8)
Controls the overall volume level of the Master Output. This level can be seen on the LED meter.
Aux Output (9)
Controls the overall volume level of the Aux Output.
Power LED (10)
Indicates that AC mains power or DC power is connected and the power switch is in the “ON” position.
Power Switch (11)
Depress the switch to the “ON” position. The red pilot light (LED) will illuminate, indicating power is being
supplied to the unit.
13 12
| | |
| i
MASTER MIÉ NE МЕНЕ MIC
Gute
= ок. РФ ® ©
> Po | = cer 7 © e e
GG RUT PHERT Eh pre LEC PLC. nap == СОТРЫТ === | ТЯ
20 WATTS WEA WADE USA
| | 1
i i I
18 17 16 15 14
Microphone Inputs (1-4) (12)
For use with low impedance microphones or low level sources.
Mic/Line Input (5,6) (13)
For use with high impedance microphones or high level sources. This input has no phantom power capability.
Master Output (14)
This 1s a transformer balanced output, used to drive an external power amplifier.
Aux Output (15)
This 1s an unbalanced output used to drive an external power amplifier.
Phantom Power Switch (16)
Selects phantom power for all Mix channels. In the “off” position no phantom power is available on any channels.
DC Input (17)
This unit may be operated from a DC power source. This DC power source must provide a minimum of
[2 Y DC and not more than 28 Y DC. H must provide at least 0.6 AMP. and be negative ground.
Line Cord (120 V Products Only) i)
For your safety, we have incorporated a 3-wire line (mains) cable with proper grounding facilities. It is not
advisable to remove the ground pin under any circumstances. If it is necessary to use the equipment without
proper grounding facilities, suitable grounding adapters should be used. Less noise and greatly reduced shock
hazard exists when the unit is operated with proper grounded receptacles.
SPECIFICATIONS
Channel Microphone Input
(Channel 1 to 4):
Microphone Impedance:
150-600 ohms
Input Impedance:
3 K ohms balanced
Nominal Input Level:
0 dBV (I V RMS)
Minimum Input Level:
-64 dBY (0.6 mV RMS)
Maximum Output Level:
+13 dBV (4.5 V RMS)
Channel/Line Input
(Channel 5,6):
Line Impedance:
10 K ohms balanced
Nominal Input Level:
0 dBY (1 Y RMS)
Minimum Input Level:
-50 dBV (3 mV RMS)
Maximum Input Level:
+13 dBV (4.5 V RMS)
Master Aux Output:
Load Impedance:
600 ohms or greater
Nominal Output:
0 dBV (1 V RMS)
Maximum Output:
+13 dBV (4.5 V RMS)
The following specifications are measured
with a nominal setting of 5 on channel 1-6,
Master and Aux, EQ, Low Mid Hi set flat.
All microphone inputs terminated with 130
ohms. All line inputs are terminated wiht 10
K ohms.
Frequency Response:
+0, -2 dB, 20 Hz to 20 kHz
Preamp Hum and Noise:
-87 dBV (all channels on)
Equivalent Input Noise:
114 dBV (150 ohms source)
Distortion:
Less than 0.02% THD (typically
below 0.01%) 1 Y RMS output,
20 Hz to 20 kHz
Equalization:
Low +15 dB at 50 Hz (shelving)
Mid +12 dB at 600 Hz
(peak/notch)
Hi +15 dB at 10 kHz (shelving)
Crosstalk:
Greater than 50 dB at 1 kHz
Channel LED Indicator:
Clipping
Maximum Available Gain:
Microphone Input Level: 44 dB
Line Input Level: 30 dB
Master Level: 20 dB
Aux Level: 20 dB
LED Meter Adjustment:
-18 dBV to clipping
Power Requirements:
120 V AC, 60 Hz, 20 watts or
+12 to +28 V DC, 0.6 amp.
=
CLIP
LED
3 AMP
MIC О ==
INPUT 0) +
LEVEL
OP 3 BAND OP
AMP EQUALIZATION AMP
PHANTOM y
POWER | 1
PHANTOM LOW MID HIGH
POWER SWITCH
ip CLIP
= LED
MIC wages 3 >=
LINE AE |} $
МРОТ
LEVE 7
This bleck diagram shows signa! flow within the unit. In order to thoroughly understand the unit's functions, please study the block diagram carafully.
THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA. ALL EXPORTED PRODUCTS ARE SUBJECT
TO WARRANTY AND SERVICES TO BE SPECIFIED AND PROVIDED BY THE AUTHORIZED DISTRIBUTOR FOR EACH COUNTRY.
Ces clauses de garantie ne sont vaiables qu'aux Etats-Unis et au Canada. Dans tour les autres pays, les clauses de garantie et de maintenance sont fixees par
le distributeur national et assuree par lul seion la legislation envigueur.
Diese Garantie ist nur in den USA and Kanada gultig. Alle Export-Produkte sind der Garantie und dem Service des Importeurs des jewelligen Landes unterworfen.
Esta garantia es valida solamente cuando el producto es comprado en E.U. continentales o en Canada. Todos los productos que sean comprados en el extranjero,
estan sujetos a las garantias y servicio que cada distribuidor autorizado determine y ofrezca en los diferentes paises.
PEAVEY ONE-YEAR LIMITED
WARRANTY/REMEDY
PEAVEY ELECTRONICS CORPORATION ("PEAVEY") warrants this product, EXCEPT for covers, foolswitches, patchcords, tubes and meters, to be free from defects
in material and workmanship for a period of one (1) year from date of purchase, PROVIDED, however, that this limited warranty is extended only to the original retail purchaser
and is subject to the conditions, exclusions; and limitations hereinafter set forth:
PEAVEY 90-DAY LIMITED WARRANTY ON TUBES AND METERS
If this product contains tubes or meters, Peavey warrants the tubes or meters contained in the product to be free from defects in material and workmanship for a period
of ninety (20) days from date of purchase; PROVIDED, however, that this limited warranty is extended only to the original retail purchaser and Is also subject to the conditions,
exclusions, and limitations hereinafter set forth.
CONDITIONS, EXCLUSIONS, AND LIMITATIONS OF LIMITED WARRANTIES
These limited warranties shall be void and of no effect, if:
a. The first purchase of the product is for the purpose of resale; or
b. The original retail purchase 18 not made from an AUTHORIZED PEAVEY DEALER; or
Cc. The product has been damaged by accident or unreasonable use, neglect, improper service or maintenance, or other causes not arising out of defects in
material or workmanship; or
d. The serial number affixed to the product Is altered, defaced, or removed.
In the event of a defect in material and/or workmanship covered by this limited warranty, Peavey will:
a. In the case of tubes or meters, replace the defective component without charge.
b. In other covered cases (i.e, cases involving anything other than covers, footswitches, patehcords, lubes or meters), repair the defect in material or workmanship
or replace the product, at Peavey's option;
and provided, however, that, in any case, all costs of shipping, if necessary, are paid by you, the purchaser
THE WARRANTY REGISTRATION CARD SHOULD BE ACCURATELY COMPLETED AND MAILED TO AND RECEIVED BY PEAVEY WITHIN FOURTEEN (14) DAYS
FROM THE DATE OF YOUR PURCHASE.
In order to obtain service under these warranties, you must:
a. Bring the defective item to any PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER and present therewith the ORIGINAL PROOF
OF PURCHASE supplied to you by the AUTHORIZED PEAVEY DEALER in connection with your purchase from him of this product.
If the DEALER or SERVICE CENTER is unable to provide the necessary warranty service you will be directed to the nearest other PEAVEY AUTHORIZED
DEALER or AUTHORIZED PEAVEY SERVICE CENTER which can provide such service.
OR
b. Ship the defective item, prepaid, to:
PEAVEY ELECTRONICS CORPORATION
International Service Center
Highway 80 East
MERIDIAN, MS 32301
including therewith a complete, detailed description of the problem, together with a legible copy of the original PROOF OF PURCHASE and a complete return
address. Upon Peavey's receipt of these items:
If the defect is remedial under these limited warranties and the other terms and conditions expressed herein have been complied with, Peavey will provide the
necessary warranty service lo repair or replace the product and will return it, FREIGHT COLLECT, to you, the purchaser.
Peavey 's liability to the purchaser for damages from any cause whatsoever and regardless of the form of action, including negligence, is limited lo the actual
damages up to the greater of 5500.00 or an amount equal to the purchase price of the product that caused the damage or that is the subject of or is directly
related to the cause of action. Such purchase price will be thal in effect for the specific product when the cause of action arose. This limitation of liability will
not apply to claims for personal injury or damage to real property or tangible personal property allegedly caused by Peavey's negligence. Peavey does not assume
liability for personal injury or property damage arising out of or caused by a non-Peavey alteration or attachment, nor does Peavey assume any responshility
for damage to interconnected non-Peavey equipment that may result from the normal functioning and maintenance of the Peavey equipment.
UNDER NO CIRCUMSTANCES WILL PEAVEY BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, ANY INCIDENTAL DAMAGES, OR ANY CONSE-
QUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT, EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES.
THESE LIMITED WARRANTIES ARE IN LIEU OF ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IM-
PLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE; PROVIDED, HOWEVER, THAT IF THE OTHER TERMS AND COND/-
TIONS NECESSARY TO THE EXISTENCE OF THE EXPRESSED, LIMITED WARRANTIES, AS HEREINABOVE STATED, HAVE BEEN COMPLIED WITH, IM-
PLIED WARRANTIES ARE NOT DISCLAIMED DURING THE APPLICABLE ONE-YEAR OR NINETY-DAY PERIOD FROM DATE OF PURCHASE OF THIS PRODUCT.
SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THESE LIMITED WARRANTIES GIVE YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
THESE LIMITED WARRANTIES ARE THE ONLY EXPRESSED WARRANTIES ON THIS PRODUCT, AND NO OTHER STATEMENT, REPRESENTATION, WAR-
RANTY, OR AGREEMENT BY ANY PERSON SHALL BE VALID OR BINDING UPON PEAVEY.
In the event of any modification or disclaimer of expressed or implied warranties, or any limitation of remedies, contained herein conflicts with applicable
law, then such modification, disclaimer or limitation, as the case may be, shall be deemed to be modified to the extent necessary to comply with such law.
Your remedies for breach of these warranties are limited to those remedies provided herein and Peavey Electronics Corporation gives this limited warranty
only with respect to equipment purchased In the United States of America.
INSTRUCTIONS — WARRANTY REGISTRATION CARD
1. Mail the completed WARRANTY REGISTRATION CARD to:
PEAVEY ELECTRONICS CORPORATION
POST OFFICE BOX 2898
MERIDIAN, MISSISSIPPI 39302-2898
a. Keep the PROOF OF PURCHASE. In the event warranty service is required during the warranty period, you will need this document. There will
be no identification card issued by Peavey Electronics Corporation.
2, IMPORTANCE OF WARRANTY REGISTRATION CARDS AND NOTIFICATION OF CHANGES OF ADDRESSES:
a. Completion and mailing of WARRANTY REGISTRATION CARDS — Should notification become necessary for any condition that may
require correction, the REGISTRATION CARD will help ensure that you are contacted and properly notified,
b. Notice of address changes — If you move from the address shown on the WARRANTY REGISTRATION CARD, you should notify Peavey of
the change of address so as to facilitate your receipt of any bulletins or other forms of notification which may become necessary in
connection with any condition that may require dissemination of information or correction.
3 You may contact Peavey directly by telephoning (601) 483-5365.
IMPORTANT SAFETY INSTRUCTIONS
WARNING When using electric products, basic cautions should always be followed, including the following,
Lan X oe ba
En
=
14.
15.
16.
Е,
18.
Read all safety and operating instructions before using this product.
All safety and operating instructions should be retained for future reference.
Obey all cautions in the operating instructions and on the back of the unit.
All operating instructions should be followed.
This product should not be used near water, i.e., a bathtub, sink, swimming pool, wet basement, été.
This product should be located so that its position does no interfere with its proper ventilation. It should not be placed flat
against a wall or placed in a built-in enclosure that will impede the flow of cooling air.
This product should not be placed near a source of heat such as a stove, radiator, or another heat producing amplifier,
Connect only to a power supply of the type marked on the unit adjacent to the power supply cord.
Never break off the ground pin on the power supply cord. For more information on grounding, write for our free booklet
“Shock Hazard and Grounding.”
Power supply cords should always be handled carefully. Never walk or place equipment on power supply cords. Periodically
check cords for cuts or signs of stress, especially at the plug and the point where the cord exits the unit.
The power supply cord should be unplugged when the unit is to be unused for long periods of time.
If this product is to be mounted in an equipment rack. rear support should be provided.
Metal parts can be cleaned with a damp rag, The vinyl covering used on some units can be cleaned with a damp rag, or an
ammonia-based household cleaner if necessary. Disconnect unit from power supply before cleaning.
Care should be taken so that objects do not fall and liquids are not spilled into the unit through the ventilation holes or any
other openings.
This unit should be checked by a qualified service technician if
a. The power supply cord or plug has been damaged.
b. Anything has fallen or been spilled into the unit.
¢., The unit does not operate correctly.
d. The unit has been dropped or the enclosure damaged.
The user should not attempt to service this equipment. All service work should be done by a gualified service technician,
This product should be used only with a cart or stand that is recommended by Peavey Electronics.
Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to
noise induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient
time.
The U.S. Governments Occupational Safety and Health Administration (OSHA) has specified the following permissible noise
level exposures.
Duration Per Day In Hours Sound Level dBA, Slow Response
8 90
6 92
4 95
3 97
2 100
144 102
| 105
4 110
4 or less 115
According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss.
Ear plugs or protectors in the ear canals or over the ears must be worn when operating this amplification system in order to
prevent a permanent hearing loss if exposure is in excess of the limits as set forth above, To ensure against potentially
dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of produc-
ing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit 1s in
operation.
SAVE THESE INSTRUCTIONS
Features and specifications subject to change without notice.
Peavey Electronics Corporation 711 A Street / Meridian, MS 38302-2898 / U.S.A. / (601) 483-5365 / Telex 504115 / Fax 484-4278
©1993 #80301976 Printed in U.S.A, 3/93