advertisement
ELECT
COLOUR
TELEVISION
25A6
29A5/29A6/29A7
29K3/29K5//29K10
29M6/29U2/29Z4
34A7/34Z4
Owner’s Instructions
Before operating the unit, please read this manual thoroughly, and retain it for future reference.
REMOTE CONTROL
ON-SCREEN MENUS
PICTURE IN PICTURE FUNCTION
TELETEXT FUNCTION
ENG
ENG
Safety Instructions
The following illustrations represent the precautions to be taken when using and moving your television.
10%
H
5°
35°
H
75%
Do NOT expose the television to extreme temperature conditions or to extreme humidity conditions.
Do NOT expose the television to direct sunlight.
Do NOT expose the television to any liquids.
If the television is broken, do not try to repair it yourself. Contact qualified service personnel.
During a storm conditions
(especially when there is lightning) unplug the television from the mains socket and aerial.
If the remote control is not used for a long period of time, remove the batteries and store it in a cool, dry place.
THIS DEVICE IS NOT FOR USE IN INDUSTRIAL ENVIRONMENTS
➣
Please use a soft and dry cloth (not containing volatile matter) when you clean the TV.
Caution
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
CAUTION:
TO PREVENT ELECTRICAL SHOCK, DO
NOT REMOVE REAR COVER, NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING:
TO PREVENT DAMAGE WHICH MAY
RESULT IN FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
☛
The main voltage is indicated on the rear of the TV set and the frequency is 50 or
60Hz.
The lightning flash and arrow head within the triangle is a warning sign alerting you of “dangerous voltage” inside the product.
The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product.
!
Mode System
CZ PAL-B/G, D/K, I, SECAM-B/G,D/K, I,
NTSC4.43
CW PAL-B/G, D/K, I, SECAM-B/G,D/K, I, L/L’,
NTSC4.43
CS PAL-B/G, D/K, I, SECAM-B/G,D/K, I,
NTSC4.43/3.58
2
Contents
◆ PREPARING YOUR TELEVISION
■ Safety Instructions .........................................................................................
■ Caution ..........................................................................................................
■ Front Control Panel .......................................................................................
■ Connection Panels ........................................................................................
■ Infrared Remote Control (All Functions Except Teletext & PIP) ....................
■ Infrared Remote Control (Teletext & PIP Functions) .....................................
■ Inserting the Batteries in the Remote Control................................................
■ Connecting the Aerial (or Cable Television Network)....................................
■ Switching Your Television On and Off...........................................................
■ Placing Your Television in Standby mode .....................................................
■ Plug & Play Feature.......................................................................................
■ Viewing the Demonstration............................................................................
■ Choosing Your Language..............................................................................
◆ SETTING UP THE CHANNELS
■ Storing the Channels Automatically...............................................................
■
■
■
■
■
Storing the Channels Manually......................................................................
Giving Channels Names................................................................................
Skipping Unwanted Channels .......................................................................
Fine tuning Channel Reception .....................................................................
Sorting the Stored Channels .........................................................................
◆ USING THE TELEVISION
■ Changing the Picture Standard .....................................................................
■ Adjusting the Picture Settings........................................................................
■ Selecting the Picture Format .........................................................................
■ Activation/Deactivation the Digital Noise Reduction Feature ........................
■ Using the Tilt Control Feature (Option)..........................................................
■ Freezing the Current Picture (Option) ...........................................................
■ Changing the Sound Standard ......................................................................
■ Adjusting the Sound Settings ........................................................................
■ Extra Sound Settings.....................................................................................
■ Selecting the Sound Mode ............................................................................
■ Selecting the Turbo Sound ............................................................................
■ Adjusting the Volume.....................................................................................
■ Switching the Sound Off Temporarily ............................................................
■ Using the LNA (Low Noise Amplifier) Feature (Option).................................
■ Setting the Sleep Timer .................................................................................
■ Setting and Displaying the Current Time.......................................................
■ Switching the Television On and Off Automatically .......................................
■ Setting the Blue Screen Mode.......................................................................
■ Activating the Childlock .................................................................................
■ Picture In Picture ...........................................................................................
◆ USING THE TELETEXT FUNCTION
■ Teletext Decoder ...........................................................................................
■
■
■
■
Displaying Teletext Information .....................................................................
Selecting a Specific Teletext Page ................................................................
Using FLOF to Select a Teletext Page ..........................................................
Storing Teletext Pages ..................................................................................
◆ INFORMATION ON CONNECTIONS AND RECOMMENDATIONS FOR USE
■ Connecting to the AV-1 or 2 Input/Outputs....................................................
■ Connecting to the S-VIDEO Input..................................................................
■ Connecting to the DVD Input.........................................................................
■ Connecting to the RCA Input.........................................................................
■ Connecting Headphones ...............................................................................
■ Viewing Picture From External Sources ........................................................
■ Automatic Degaussing to Remove Colour Patches.......................................
■ Trouble Shooting: Before Contacting Service Personnel ..............................
Symbols
☛ ➢
Press Important Note
3
33
33
34
35
35
13
14
16
17
18
19
38
38
39
39
36
36
37
37
8
8
6
7
4
5
2
2
10
11
9
9
12
27
27
28
28
25
26
26
27
29
30
30
31
22
23
23
24
20
21
21
22
ENG
ENG
Front Control Panel
(depending on the model)
➣
Buttons and markings are subject to change.
❶
TV/VIDEO SELECTION
❷
MENU DISPLAY
❸
VOLUME ADJUSTMENT
❹
CHANNEL SELECTION
❺
STAND-BY/TIMER INDICATOR
❺
*
STAND-BY INDICATOR
❻
REMOTE CONTROL SENSOR
❼
POWER
4
Connection Panels
☛
This figure shows the Standard Connector-jack panel.
The actual configuration on your TV may be different, depending on the model.
Side of TV Front of TV
RCA AUDIO/VIDEO INPUT
CONNECTORS
S-VIDEO INPUT JACK
HEADPHONE JACK
HEADPHONE JACK RCA AUDIO/VIDEO INPUT
CONNECTORS
S-VIDEO INPUT JACK
Rear of TV
MONITOR
-OUT
VIDEO
(MONO)
L-AUDIO-R
INPUT 2
INPUT 1
MONITOR
-OUT
VIDEO
(MONO)
L-AUDIO-R
INPUT 2
INPUT 1
2
RGB
1
❶ RCA AUDIO/VIDEO INPUT/OUTPUT
CONNECTORS
❷ DVD INPUT CONNECTORS
❸ SCART AUDIO/VIDEO INPUT/OUTPUT
CONNECTORS
❹ 75 Ω COAXIAL CONNECTOR FOR
AERIAL/CABLE NETWORK
ENG
5
ENG
Infrared Remote Control (All Functions Except Teletext & PIP)
➣
Buttons and markings are subject to change.
POWER
ON-SCREEN DISPLAY
PICTURE MENU DISPLAY
AUTOMATIC SWITCH-OFF
ONE/TWO-DIGIT CHANNEL
SELECTION
SOUND MENU DISPLAY
TURBO SOUND ON/OFF
OPTION
TUNER/CABLE NETWORK
SELECTION
VOLUME DECREASE
PREVIOUS CHANNEL
PICTURE SIZE
DIRECT CHANNEL SELECTION
SOUND MODE SELECTION
SOUND STANDARD
PICTURE STANDARD
STILL PICTURE
EXTERNAL INPUT SELECTION
NEXT CHANNEL
VOLUME INCREASE
MENU DISPLAY
TEMPORARY SOUND SWITCH-
OFF
➣
Operation of remote control may be affected by bright artificial light near to the TV set.
6
Infrared Remote Control (Teletext & PIP Functions)
➣
Buttons and markings are subject to change.
TELETEXT REVEAL
TELETEXT STORE
TELETEXT HOLD
FASTEXT TOPIC SELECTION
PIP SIZE SELECTION
(OPTION)
PIP CHANNEL SELECTION
(OPTION)
PIP SOURCE SELECTION
(OPTION)
TELETEXT NEXT PAGE
TELETEXT PREVIOUS PAGE
TELETEXT SIZE
PIP ON
PIP SWAP
PIP LOCATE
PIP STILL
TELETEXT SUB-PAGE
(OPTION)
PIP SCAN (OPTION)
TELETEXT DISPLAY/MIX
LIST/FLOF MODE SELECTION
PROGRAMME SELECTION
BY NAME
ENG
7
ENG
PRESS
Inserting the Batteries in the Remote Control
You must insert or replace the batteries in the remote control when you :
◆ Purchase the television.
◆ Find that the remote control is no longer operating correctly.
1 Remove the cover of the remote control by pressing the symbol
( PRESS ) and pulling the cover in the direction of the arrow.
2 Insert batteries, taking care to respect the polarities:
◆
◆
+ on the battery with + on the remote control
-
on the battery with
-
on the remote control
3
Replace the cover by pushing it in the direction of the arrow.
PRESS
Connecting the Aerial (or Cable Television Network)
To view television channels correctly, a signal must be received by the set from one of the following sources:
◆ An outdoor aerial
◆ A cable television network
Plug the aerial or cable network input cable to the 75Ω coaxial socket on the rear of the television.
Rear of TV
8
Cable
Television
Network
Switching Your Television On and Off
The mains lead is attached to the rear of the television.
1
Plug the mains lead into an appropriate socket.
➢
The main voltage is indicated on the rear of the TV set and the frequency is 50 or 60Hz.
2 Press the POWER (ON/OFF) button on the front of the television.
Result: The Standby indicator lights up on the front panel.
3 Press the POWER button on the remote control to switch the television on.
Result: The programme that you were watching last is reselected automatically.
4 To switch your television off, press the POWER (ON/OFF) button again on the front of the television.
Placing Your Television in Standby mode
Your television can be placed in Standby mode, in order to reduce:
◆ Power consumption
◆ Wear of the cathode ray tube
The Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).
The television is placed automatically in Standby mode when you turn it on.
1 Press the POWER button on the remote control.
Result: The screen is turned off and the Standby indicator on the front of the television lights up.
2 To switch the screen back on, simply press the POWER button again on the remote control.
➣
Do not leave your television in standby mode for long periods of time (when you are away on holiday, for example).
In this case, you should switch it off completely.
9
ENG
ENG
Plug & Play Feature
Plug & Play
Ant. Input : Check
Select Exit
Auto store
Area : ASIA W/EUROPE
Search : -/+
Select Adjust Exit
Time
Clock : -- : -- am
Timer : Off
Select Enter Exit
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock
Demonstration
Select Enter Exit
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock
Demonstration
Select Enter Exit
When the television is initially powered ON, three basic customer settings proceed automatically and subsequently: setting the language, channel and clock.
1
If the television is in Standby mode (red light visible on the television front panel), press the POWER button on the remote control.
Result: The message “Plug & Play” is displayed. It flickers for a little while and then the “Language” menu is automatically displayed.
2
Press the
▲ or ▼ button to select required language. Press the
MENU button to enter the language, and then the message “Ant.
Input : Check” is displayed.
➣
If any language is not selected on the “Language” menu, the
“Language” menu will be displayed about 30 seconds later.
3 Make sure that the antenna is connected to the TV. And then press the + or – button.
Result: The “Auto store” menu is displayed.
4 Select your country by pressing the + or – button. To search the channels, select the “Search” by pressing the
▲ or ▼ button, and then press the + or – button (refer to “Storing the Channels
Automatically” on page 13). Press the MENU button to skip.
Result: The “Time” menu is displayed.
5
Press the
+ or
– button to move to the hour or minute. Set the hour or minute by pressing the
▲ or ▼ button (refer to “Setting and
Displaying the Current Time” on page 28).
6
When you have finished, press the MENU button.
Result: The message “ENJOY YOUR WATCHING” is displayed, and then the channel which has been stored will be activated.
7 If you want to reset this feature...
1 Press the MENU button.
2 Press the
▲ or ▼ button to select the “Function”, and then press the + or – button.
3 Select the “Plug & Play” by pressing the
▲ or ▼ button, and then press the
+ or
– button.
Result: The message “Plug & Play” is displayed.
10
Viewing the Demonstration
To become familiar with the various menus provided by your television, you can view the inbuilt demonstration.
1 Press the MENU button.
2 Press the
▲ or ▼ button to select the “Function” and press the + or
– button.
3 Press the
▲ or ▼ button to select the “Demonstration” and press the + or – button.
Result: Each of the menu options is displayed in turn.
4 When you wish to stop the demonstration, press any button on the remote control.
Picture
Mode Custom
Adjust
Digital NR : Off
Tilt : 0
LNA : Off
Select Enter Exit
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock
Demonstration
Select Enter Exit
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock
Demonstration
Select Enter Exit
ENG
11
ENG
Picture
Mode Custom
Adjust
Digital NR : Off
Tilt : 0
LNA : Off
Select Enter Exit
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock
Demonstration
Select Enter Exit
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock
Demonstration
Select Adjust Exit
Choosing Your Language
When you start using your television for the first time, you must select the language which will be used for displaying menus and indications.
1
Press the MENU button.
2
Press the
▲ or ▼ button to select the “Function”.
3 Press the + or – button to select the “Language”.
4 Select a particular language by pressing the
▲ or ▼ button repeatedly.
5 When you have finished, press the TV button, or press the MENU button repeatedly to return to normal viewing.
12
Storing the Channels Automatically
You can scan the frequency ranges available on your television and in your area and store all the channels found automatically.
The channels are stored in the order in which they appear in the frequency bands. It is possible that the automatically allocated numbers may not correspond to those by which you wish to identify the channels. If this is the case, refer to “Sorting the Stored
Channels” on page 19.
1 Press the MENU button.
2 Press the
▲ or ▼ button to select the “Channel”.
3 Press the + or – button to select the “Auto store”.
4 Press the + or – button again.
Result: The “Auto store” menu is displayed with the “Area” selected.
5
Select your country by pressing the
+ or
– button. The following countries are available: ASIA W/EUROPE - CIS E/EUROPE -
CHINA - HONGKONG U/K - AUSTRALIA - NZ/INDONESIA -
SOUTH AFRICA - AMERICA.
6
Press the
▲ or ▼ button to select the “Search” and press the + or
– button.
Result: The horizontal bar is displayed, and then channels are stored in an order which reflects their positions in the frequency range. Finally, the search will end automatically.
7 When searching and storing is complete, the “Sort” menu is displayed.
To...
Sort the stored channels into the desired numerical order
Exit the channel store function without sorting the channels
Then...
Go to Step 4 of the “Sorting the Stored Channels” procedure on page 19.
Press the MENU button repeatedly until the menus disappear.
Channel
Auto store
Manual store
Name
Add/Erase
Fine tune
Sort
Select Enter Exit
Auto store
Area : ASIA W/EUROPE
Search : -/+
Select Adjust Exit
Auto store
Area : ASIA W/EUROPE
Search : -/+
Select Search Exit
P 8 C25 -----
426 MHz 22 %
Exit
Sort
From : P 1
To : P--
Store : ?
Select Adjust Exit
ENG
13
ENG
Channel
Auto store
Manual store
Name
Add/Erase
Fine tune
Sort
Select Enter Exit
Channel
Auto store
Manual store
Name
Add/Erase
Fine tune
Sort
Select Enter Exit
Manual store
Color system : Auto
Sound system : BG
Search : 138MHz
Channel : S 6
Prog.No. : P12
Store : ?
Select Adjust Exit
Manual store
Color system : Auto
Sound system : BG
Search : 138MHz
Channel : S 6
Prog.No. : P12
Store : ?
Select Adjust Exit
Storing the Channels Manually
When storing channels manually, you can choose:
◆ Whether or not to store each of the channels found.
◆ The number by which you wish to identify each stored channel.
1 Press the MENU button.
2 Press the
▲ or ▼ button to select the “Channel” and press the + or
– button.
3 Press the
▲ or ▼ button to select the “Manual store” and press the
+ or – button.
Result: The “Manual store” menu is displayed with the “Color system” selected.
4 Press the + or – button repeatedly until the color is of the best quality.
Result: The “Color system” is changed.
Auto
↔ PAL ↔ SECAM ↔ NT4.43 ↔ NT3.58 (option)
➣
NT4.43 is a “trick” playback mode used by special VCR’s to play PAL-recorded videos in NTSC mode.
5 Press the
▲ or ▼ button to select the “Sound system” and press the + or – button repeatedly until the sound is of the best quality.
Result: The “Sound system” is changed.
BG
↔ DK ↔ I ↔ M (option)
14
Storing the Channels Manually
(continued...)
6 If you know the number of the channel to be stored, press the...
1.
▲ or ▼ button to select the “Channel”.
2.
+ button.
3.
▲ or ▼ button to select the “C” (Air channel) or “S” (Cable channel).
4.
+ button.
5.
▲ or ▼ button to select the channel.
➣
If no sound or abnormal sound...
1.
Press the
+ button.
2.
Press the
▲ or ▼ button to select the “Sound system”.
3.
Select the “BG”, “DK”, “I” or “L” by pressing the
+ or
– button.
If you do not know the channel numbers, press the...
1.
▲ or ▼ button to select the “Search”.
2.
+ or – button to start the search.
Result: The tuner scans the frequency range until the first channel or the channel that you selected is received on your screen.
7 To assign a programme number to the channel, select the
“Prog.No.”. Press the + or – button until you find the correct number.
8 To store the channel and associated programme number, select the “Store” and press the + or – button.
Result: “OK” is displayed.
9 Repeat Steps 6 to 8 for each channel to be stored.
10 When you have finished manual storage, press the TV button, or press the MENU button repeatedly to return to normal viewing
Manual store
Color system : Auto
Sound system : BG
Search : 138MHz
Channel : S 6
Prog.No. : P12
Store : ?
Select Adjust Exit
Manual store
Color system : Auto
Sound system : BG
Search : 138MHz
Channel : S 6
Prog.No. : P12
Store : ?
Select Search Exit
Manual store
Color system : Auto
Sound system : BG
Search : 138MHz
Channel : S 6
Prog.No. : P12
Store : ?
Select Adjust Exit
Manual store
Color system : Auto
Sound system : BG
Search : 138MHz
Channel : S 6
Prog.No. : P12
Store : OK
Select Adjust Exit
15
ENG
ENG
Channel
Auto store
Manual store
Name
Add/Erase
Fine tune
Sort
Select Enter Exit
Name
P 0 : -----
P 1 : -----
P 2 : -----
P 3 : -----
Select Enter Exit
Name
P 0 : -----
P 1 : -----
P 2 : -----
P 3 : -----
Adjust Move Exit
Giving Channels Names
If you want edit the name, you can assign new names as required.
1
Press the MENU button.
2
Press the
▲ or ▼ button to select the “Channel” and press the + or
– button.
3 Press the ▲ or ▼ button to select the “Name” and press the + or – button.
4 To...
Select a letter or number
Move on the next letter
Press the...
▼ or ▲ button.
+ button.
– button.
Move back the previous letter
➣
The characters available are:
◆ Letters of the alphabet (A...Z)
◆ Numbers (0...9)
◆ Special characters (space, -)
5 You can have each channel newlynamed.
6 When you have finished entering the name, press the TV button, or press the MENU button repeatedly to return to normal viewing.
16
Skipping Unwanted Channels
You can exclude the channels of your choice from the channel scan operation. When you scan through the stored channels, those you have chosen to skip are not displayed.
All channels that you do not specifically choose to skip are displayed during scanning.
1
Press the MENU button.
2
Press the
▲ or ▼ button to select the “Channel” and press the + or
– button.
3 Press the ▲ or ▼ button to select the “Add/Erase” and press the + or – button.
Result: The “Add/Erase” menu is displayed.
4 Press the
▲ or ▼ button to select the required channel.
5 To add or erase the desired channel by pressing the + or – button.
6 When you have finished adding and erasing channels, press the
TV button, or press the MENU button repeatedly to return to normal viewing
Channel
Auto store
Manual store
Name
Add/Erase
Fine tune
Sort
Select Enter Exit
Add/Erase
P 0 : Added
P 1 : Added
P 2 : Added
P 3 : Added
Select Adjust Exit
Add/Erase
P 0 : Erased
P 1 : Added
P 2 : Added
P 3 : Added
Select Adjust Exit
ENG
17
ENG
Channel
Auto store
Manual store
Name
Add/Erase
Fine tune
Sort
Select Enter Exit
Fine tune
Tune : -/+
Store : ?
Erase : ?
Select Adjust Exit
Fine tune
Fine tuning Channel Reception
Fine tune
Tune : -/+
Store : OK
Erase : ?
If the reception is clear, you do not have to fine-tune the channel, as this is done automatically during the search and store operation.
If however the signal is weak or distorted, you may have to finetune the channel manually.
1
Press the MENU button.
2
Press the
▲ or ▼ button to select the “Channel” and press the + or
– button.
3 Press the ▲ or ▼ button to select the “Fine tune” and press the + or – button.
Result: The “Fine tune” menu is displayed with the “Tune” selected.
4 To...
obtain a sharp and clear picture and good sound quality memorise adjusted picture or sound erase adjusted picture or sound
Press the...
◆ + or – button.
Result: The horizontal bar’s cursor moves to the left or right.
◆ ▲ or ▼ button to select the “Store”.
◆ + or – button.
Result: “OK” is displayed.
◆ ▲ or ▼ button to select the “Erase”.
◆ + or – button.
Result: “OK” is displayed.
5 When you have finished, press the TV button, or press the MENU button repeatedly to return to normal viewing.
Select Adjust Exit
Fine tune
Tune : -/+
Store : ?
Erase : OK
Select Adjust Exit
18
Sorting the Stored Channels
You can exchange the numbers of two channels, in order to:
◆ Modify the numeric order in which the channels have been automatically stored.
◆ Give easily remembered numbers to the channels that you watch most often.
1 Press the MENU button.
2 Press the
▲ or ▼ button to select the “Channel” and press the + or
– button.
3 Press the
▲ or ▼ button to select the “Sort” and press the + or – button.
Result: The “Sort” menu is displayed with the “From” selected.
4 Press the + or – button until the channel number that you wish to change is displayed.
Result: The selected channel’s picture is displayed.
5 Press the
▲ or ▼ button to select the “To”.
6
Press the
+ or
– button until the new number by which you wish to identify the channel is displayed.
Result: The selected channel is exchanged with the one previously stored to the chosen number.
Example: If you select “ P 1” for the “From” and “P 3” for the “To”:
◆ Channel 1 becomes channel 3.
◆ Channel 3 becomes channel 1.
7 To...
Press the...
Confirm the exchange of channel numbers
◆ ▲ or ▼ button to select the “Store”.
◆ + or – button.
Result: “OK” is displayed.
➣
You can exchange other channel numbers by selecting
“From” and returning to step
4
.
8 When you have finished sorting channels, press the TV button, or press the MENU button repeatedly to return to normal viewing
Channel
Auto store
Manual store
Name
Add/Erase
Fine tune
Sort
Select Enter Exit
Sort
From : P 1
To : P--
Store : ?
Select Adjust Exit
Sort
From : P 1
To : P 3
Store : ?
Select Adjust Exit
Sort
From : P 3
To : P 1
Store : OK
Select Adjust Exit
ENG
19
ENG
Picture
Mode Custom
Adjust
Digital NR : Off
Tilt : 0
LNA : Off
Select Enter Exit
Picture
Mode Custom
Adjust
Digital NR : Off
Tilt : 0
LNA : Off
Select Adjust Exit
Changing the Picture Standard
You can select the type of picture which best corresponds to your viewing requirements. The following picture effects are available in the order given:
◆ Custom, Standard, Sports, Natural, Mild.
1
Press the MENU button.
Result: The “Picture” menu is displayed.
2 Press the + or – button to select the “Mode”.
3
Press the
+ or
– button repeatedly to cycle through the five choices: Custom, Standard, Sports, Natural, Mild.
4
When you are satisfied with the settings, press the TV button, or press the MENU button repeatedly to return to normal viewing.
You can use your remote control to select the type of picture which best corresponds to your viewing requirements.
To select the required picture effect, simply press the P.STD (Picture standard) button on the remote control.
Result: The following picture effects are available in the order given:
Custom ↔ Standard ↔ Sports ↔ Natural ↔ Mild
➢
You can display the picture menu directly by pressing the
“P.MENU” (Picture menu) button on the remote control.
20
Adjusting the Picture Settings
Your television has several settings which allow you to control picture quality:
◆ Color tone, Contrast, Brightness, Color, Sharpness, Tint
(NTSC only)
1 Press the MENU button.
Result: The “Picture” menu is displayed.
2 Press the + or – button.
3
Press the
▲ or ▼ button to select the “Adjust”, and then press the + or
– button.
Result: The “Adjust” menu is displayed.
➣
When select the “Mode” to “Custom”, the “Adjust” menu is displayed.
4
To adjust the...
◆ Color tone
Press the...
◆ + or – button.
Result: You select the required option
(Normal, Warm1/2, Cool1/2).
◆ Contrast
◆ Brightness
◆ Sharpness
◆ Color
◆ Tint (NTSC only)
◆ + or – button.
Result: The horizontal bar is displayed.
5
When you are satisfied with the settings, press the TV button, or press the MENU button repeatedly to return to normal viewing.
➣
The television has an “automatic degaussing” system that is activated if magnetic interference is present. To degauss the television screen, switch power off by pressing the “POWER ”
(ON/OFF) button on the front panel (refer to “Automatic
Degaussing To Remove Colour Patches” on page 39).
➣
If you make any changes to the “Adjust” settings, the picture standard is automatically switched to “Custom”.
Picture
Mode Custom
Adjust
Digital NR : Off
Tilt : 0
LNA : Off
Select Enter Exit
Adjust
Color tone : Normal
Contrast : 100
Brightness : 50
Sharpness : 50
Color : 50
Select Adjust Exit
Adjust
Color tone : Normal
Contrast : 100
Brightness : 50
Sharpness : 50
Color : 50
Select Adjust Exit
Contrast 100
ENG
Selecting the Picture Format
(depending on the model)
You can select the picture format which best corresponds to your viewing requirements by simply pressing the “P.SIZE” button.
Picture format
Plus
Normal
Zoom
16:9
Description
Full 12.8:9 format (extra 1 inch)
Setting for normal 4:3 format.
Expansion of a 16:9 picture to full screen format.
Setting for the 16:9 screen format
21
ENG
Picture
Mode Custom
Adjust
Digital NR : Off
Tilt : 0
LNA : Off
Select Enter Exit
Picture
Mode Custom
Adjust
Digital NR : On
Tilt : 0
LNA : Off
Select Adjust Exit
Activating/Deactivating the Digital Noise Reduction Feature
If the broadcast signal received by your television is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen.
1 Press the MENU button.
Result: The “Picture” menu is displayed.
2 Press the + or – button.
3
Press the
▲ or ▼ button to select the “Digital NR”.
4 To select the “On” by pressing the + or – button.
5 When you have finished, press the TV button, or press the MENU button repeatedly to return to normal viewing.
Using the Tilt Control Feature (Option)
Picture
Mode Custom
Adjust
Digital NR : Off
Tilt : 0
LNA : Off
Select Adjust Exit
If you find that the picture received is slightly tilted to one side, you can adjust the tilt setting.
1 Press the MENU button.
Result: The “Picture” menu is displayed.
2
Press the
+ or
– button.
3 Press the ▲ or ▼ button to select the “Tilt”.
4 To adjust the “Tilt” (±7) by pressing the + or – button.
5 When you are satisfied with the settings, press the TV button, or press the MENU button repeatedly to return to normal viewing.
22
Freezing the Current Picture (Option)
You can freeze the picture when watching a television programme.
To...
Freeze the picture on a given frame
Return to normal viewing
Press the...
STILL PICTURE button.
STILL PICTURE button again.
Changing the Sound Standard
(depending on the model)
You can select the type of special sound effect to be used when watching a given broadcast. The following sound effects are available in the order given:
◆ Custom, Standard, Music, Movie, Speech.
1 Press the MENU button.
2 Press the
▲ or ▼ button to select the “Sound” and press the + or – button.
3
Press the
+ or
– button repeatedly to cycle through the five choices: Custom, Standard, Music, Movie, Speech.
4 When you are satisfied with the settings, press the TV button, or press the MENU button repeatedly to return to normal viewing.
You can use your remote control to select the type of special sound effect to be used when watching a given broadcast.
To select the required sound effect, simply press the S.STD (Sound standard) button on the remote control.
Result: The following sound effects are available in the order given:
Custom
↔ Standard ↔ Music ↔ Movie ↔ Speech
➢
You can display the sound adjust (or equalizer) menu directly by pressing the “S.MENU” (Sound menu) button on the remote control.
Sound
Mode Custom
Equalizer
Auto volume : Off
Melody : Off
Pseudo stereo : Off
Select Enter Exit
Sound
Mode Custom
Equalizer
Auto volume : Off
Melody : Off
Pseudo stereo : Off
Select Adjust Exit
23
ENG
ENG
Sound
Mode Custom
Equalizer
Auto volume : Off
Melody : Off
Pseudo stereo : Off
Select Enter Exit
R
Equalizer
L
100 300 1K 3K 10K
Adjust Move Exit
Adjusting the Sound Settings
The sound settings can be adjusted to suit your personal preferences.
1
Press the MENU button.
2 Press the
▲ or ▼ button to select the “Sound” and press the + or – button.
3 Press the ▲ or ▼ button to select the “Equalizer”.
➣
When select the “Mode” to “Custom”, the “Equalizer” menu is displayed.
4 Press the + or – button.
Result: The “Equalizer” menu is displayed.
5 Select the required option and adjust to satisfy your preference.
6
When you are satisfied with the settings, press the TV button, or press the MENU button repeatedly to return to normal viewing.
24
Extra Sound Settings
(depending on the model)
The following sound settings can be adjusted to suit your personal preferences.
◆ Auto volume
Each broadcasting station has its own signal conditions, and so it is not easy for you to adjust the volume every time the channel is changed. “Auto volume” lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.
◆ Melody
You can hear clear melody sound when the TV is powered ON or OFF.
◆ Pseudo stereo / Virtual surround
“Pseudo stereo” converts a monaural sound signal into two identical left and right channels.
Once the “Pseudo stereo” or “Virtual surround” is set to
“On” or “Off”, the setting applies to the sound effects such as Standard, Music, Movie and Speech.
1 Press the MENU button.
2 Press the
▲ or ▼ button to select the “Sound” and press the + or – button.
3 To...
Change an option
Select the required option (On/Off)
Press the...
▲ or ▼ button.
+ or – button.
4 When you are satisfied with the settings, press the TV button, or press the MENU button repeatedly to return to normal viewing.
➣
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
Sound
Mode Custom
Equalizer
Auto volume : Off
Melody : Off
Pseudo stereo : Off
Select Enter Exit
Sound
Mode Custom
Equalizer
Auto volume : On
Melody : Off
Pseudo stereo : Off
Select Adjust Exit
Sound
Mode Custom
Equalizer
Auto volume : Off
Melody : On
Pseudo stereo : Off
Select Adjust Exit
Sound
Mode Custom
Equalizer
Auto volume : Off
Melody : Off
Pseudo stereo : On
Select Adjust Exit
Sound
Mode Custom
Equalizer
Auto volume : Off
Melody : Off
Pseudo stereo : Off
Virtual surround : On
Select Adjust Exit
ENG
25
ENG
Selecting the Sound Mode
(depending on the model)
The “S.MODE” button displays/controls the processing and output of the audio signal. When power is switched ON, the mode is automatically preset to either “Dual-I” or “Stereo”, depending on the current transmission.
On-screen indication Type of broadcast
Regular broadcast
(Standard audio)
Regular +
NICAM Mono
NICAM
Stereo
NICAM Stereo
NICAM Dual-I/II
Mono (Normal use)
Mono
↔ Mono
Nicam (Normal)
Stereo
↔ Mono
Nicam (Normal)
Dual-I → Dual-II → Mono
Nicam Nicam (Normal)
Regular broadcast
(Standard audio)
Mono (Normal use)
A2
Stereo
Bilingual or Dual-I/II Dual-I ↔ Dual-II
Stereo
Stereo ↔ Mono
(Forced Mono)
➣
◆ If the receiving conditions deteriorate, listening will be easier if the mode is set to the “Mono” position using the
“S.MODE” button.
◆ If the stereo signal is weak (or if intermittent Stereo-Mono) and automatic switching occurs, then switch to the
“Mono” mode.
◆ When receiving mono sound in the AV mode, connect to the “L” input jack on the panels. If the mono sound comes out only from the left speaker, then press the
“S.MODE” button.
Selecting the Turbo Sound
(depending on the model)
Turbo sound suitably emphasizes both higher and lower bands of sound (and includes other effects).
To enjoy more magnificent and dynamic sound when watching music, movie or other channel, simply press the TURBO button on the remote control.
Turbo sound : On
26
Adjusting the Volume
◆ Press the + button to increase the volume (cursor moves to the right)
◆ Press the button to decrease the volume (cursor moves to the left)
➣
The volume setting is retained:
◆ When you switch the television to standby mode
◆ When you switch the television off using the
“POWER ” (ON/OFF) button on the front panel
◆ If there is a power failure.
Volume 12
Switching the Sound Off Temporarily
You can switch the sound off temporarily, for example you may wish to answer the telephone.
1 Press the MUTE button.
Result: The sound is switched off and “ ” is displayed.
2 When you wish to turn the sound back on at the same volume as before, press the MUTE button again (or either of the volume buttons).
Using the LNA (Low Noise Amplifier) Feature (Option)
This feature is very useful in the situation that the TV is used in weak signal. LNA amplifies the TV signal in the weak signal area, but not noise.
This feature is working only weak signal condition, and that is memorized on current channel, additional.
1 Press the MENU button.
Result: The “Picture” menu is displayed.
2 Press the + or – button.
3 Press the
▲ or ▼ button to select the “LNA”.
4 To select the “On” by pressing the + or – button.
5 When you have finished, press the TV button, or press the MENU button repeatedly to return to normal viewing.
Picture
Mode Custom
Adjust
Digital NR : Off
Tilt : 0
LNA : On
Select Adjust Exit
27
ENG
ENG
Setting the Sleep Timer
You can select a time period of between 30 and 180 minutes after which the television automatically switches to Standby mode by pressing the "SLEEP" button.
1 Press the SLEEP button on the remote control.
Result:
If the sleep timer is...
Already set
The screen displays...
Time remaining before the television will be placed in standby mode.
Word “Off”.
Not yet set
2 Press the SLEEP button repeatedly and cycle through the preset time intervals (30, 60, 90, 120, 150, 180).
Result: The television automatically switches to standby mode when the timer reaches 0.
3
To cancel the sleep timer function, press the SLEEP button repeatedly and select “Off”.
Setting and Displaying the Current Time
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock : Off
Demonstration
Select Enter Exit
Time
Clock : 11 : 35 am
Timer : Off
Select Adjust Exit
You can set the television’s clock so that the current time is displayed when you press the “DISPLAY” button.
You must also set the time if you wish to use the automatic On/Off timers.
➣
The clock will be re-set when pressing the “POWER ”
(ON/OFF) button on the front panel.
1 Press the MENU button.
2
Press the
▲ or ▼ button to select the “Function” and press the or
+ button.
3 Press the
▲ or ▼ button to select the “Time”, and press the or + button.
Result: The “Time” menu is displayed with the “Clock” selected.
4 To...
Press the...
Move to the hour or minute
Set the hour or minute
or + button.
▲ or ▼ button.
5 When you have finished, press the TV button, or press the MENU button repeatedly to return to normal viewing.
6
To display the...
Press the DISPLAY button...
Channel information Once.
Current time Twice.
7 To remove the display, press the DISPLAY button again.
28
Switching the Television On and Off Automatically
You can set the On/Off timers so that the television will:
◆ Switch on automatically and tune to the channel of your choice at the time you select
◆ Switch off automatically at the time you select
➣
The first step is to set the television’s clock (refer to
“Setting and Displaying the Current Time” on the previous page). If you have not yet set the clock, the message “Set the clock first” is displayed.
1
Press the MENU button.
2
Press the
▲ or ▼ button to select the “Function” and press the or
+ button.
3 Press the ▲ or ▼ button to select the “Time”, and press the or + button.
Result: The “Time” menu is displayed.
4 Press the
▲ or ▼ button to select the “Timer”.
5 Press the or + button to set the mode to “On”.
Result: The “On time” and “Off time” options are displayed.
6 Press the
▲ or ▼ button to select the “On time”.
7 Set the time at which you wish the television to be switched On.
To...
Move to the hour or minute
Adjust the hour or minute
Press the...
or + button.
▲ or ▼ button.
8
In the same way, set the time at which you wish the television to be switched Off.
9 When you have finished setting the On/Off time, press the TV button, or press the MENU button repeatedly to return to normal viewing.
Time
Clock : 11 : 35 am
Timer : Off
Select Adjust Exit
Time
Clock : 11 : 35 am
Timer : On
On Time : -- : --
Off Time : -- : --
Select Adjust Exit
Time
Clock : 11 : 35 am
Timer : On
On Time : 07 : 00 am
Off Time : -- : --
Select Adjust Exit
Time
Clock : 11 : 35 am
Timer : On
On Time : 07 : 00 am
Off Time : 11 : 30 pm
Select Adjust Exit
ENG
29
ENG
Setting the Blue Screen Mode
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock
Demonstration
Select Adjust Exit
If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background.
If you wish to continue viewing the poor picture, you must set the
“Blue screen” mode to “Off”.
1 Press the MENU button.
2 Press the
▲ or ▼ button to select the “Function” and press the or
+ button.
3 Press the
▲ or ▼ button to select the “Blue screen”.
4
Press the
or
+ button to select the required option (On/Off).
5 When you have finished, press the TV button, or press the MENU button repeatedly to return to normal viewing.
Activating the Childlock
Function
Language : English
Time
Plug & Play
Blue screen : Off
Childlock
Demonstration
Select Adjust Exit
Childlock
Childlock : On
Prog.No. : P 1
Lock : ?
Select Adjust Exit
Childlock
Childlock : On
Prog.No. : P 1
Lock : Locked
You can restrict viewing by locking the channels of your choice.
Example: You can prevent your children from watching unsuitable programmes.
1 Press the MENU button.
2
Press the
▲ or ▼ button to select the “Function” and press the or
+ button.
3 Press the
▲ or ▼ button to select the “Childlock” and press the or + button.
4 Set to “On” by pressing the or + button.
➣
If you want to unlock a channel, set to “Off”.
5 Press the ▲ or ▼ button to select the “Prog.No.”. Select the number of the channel to be locked by pressing the or + button.
6 Press the ▲ or ▼ button to select the “Lock” and press the or + button.
Result: “Locked” is displayed.
7 When you have finished, press the TV button, or press the MENU button repeatedly to return to normal viewing.
➣
If any channel is locked, you cannot enter the “Channel” menu (the message “Not available” is displayed).
Select Adjust Exit
30
Picture In Picture
(depending on the model)
You can display a “Picture-In-Picture screen” within the main picture of TV program or Video input. In this way you can watch or monitor TV program or the Video input from any connected equipment while watching TV or other Video input.
For information about connection of other equipment, see pages
36~37.
1
Press the MENU button.
2
Press the
▲ or ▼ button to select the “PIP”.
3 Set to “PIP : On” by pressing the or + button.
4 Press the
▲ or ▼ button to select the “Select” and press the or + button repeatedly.
Result: You can assign a source of sub picture:
TV / AV1 / AV2 / S-Video
5 Press the ▲ or ▼ button to select the “Prog.No.”.
6 Select the channel that you want to view through sub picture by pressing the or + button.
7 Press the
▲ or ▼ button to select the “Size” and press the or + button repeatedly.
Result: You can select the type of sub picture (depending on the model):
◆
Large / Small
◆
Large / Small / 3-PIP / 4-PIP / 9-PIP
◆
Large / Small / Double screen1 / Double screen2 /
3-PIP / 4-PIP / 9-PIP
8
When you have finished, press the TV button, or press the MENU button repeatedly to return to normal viewing.
PIP
PIP : Off
Select Adjust Exit
PIP
PIP : On
Select : TV
Prog.No. : P 1
Size : Large
Select Adjust Exit
PIP
PIP : On
Select : TV
Prog.No. : P 1
Size : Large
Select Adjust Exit
PIP
PIP : On
Select : TV
Prog.No. : P 1
Size : Large
Select Adjust Exit
PIP
PIP : On
Select : TV
Prog.No. : P 1
Size : Large
Select Adjust Exit
ENG
31
ENG
Picture In Picture
(depending on the model)
Remote-control functions while “PIP” is “On”:
Features
PIP ON
SWAP
Description
Used to operate ON/OFF function of PIP directly.
Used to interchange the main picture and the sub picture.
➢
When the main picture is in the Video mode and the sub picture is in the TV mode, you might not hear the sound of main picture when pressing the SWAP button after changing the sub picture channel. At this time, reselect the main picture channel.
LOCATE
STILL
CH
▼/▲
SIZE
Used to move the sub picture counterclockwise.
Used to freeze the sub picture.
Used to select the channel of sub picture.
Used to select the type of sub picture.
TV/VIDEO Used to assign a source of sub picture (TV, AV1, AV2,
S-Video).
SCAN Used to scan every memorized channel in order.
To stop scanning, press it again.
32
Teletext Decoder
Most television channels carry “teletext,” pages of written information that provide information such as:
◆ Television programme times
◆ News bulletins
◆ Weather forecasts
◆ Sports results
◆ Subtitles for the hard of hearing
The teletext pages are organized according to six categories:
Part
C
D
E
A
B
F
Contents
Selected page number.
Broadcasting station identity.
Current page number or search status
Date and time.
Text.
Status information.
Displaying Teletext Information
You can display teletext information at any time, but signal reception must be good. Otherwise:
◆ Information may be missing
◆ Some pages may not be displayed
To activate the teletext mode and display the contents page:
1 Using the ▲ ( ) or ▼ ( ) button, select the channel providing the teletext service.
2 Press the TTX/MIX button to activate the teletext mode.
Result: The contents page (page 100) is displayed. It can be redisplayed at any time by pressing the INDEX ( ) button.
3 To display the actual broadcast simultaneously with the teletext page, press the TTX/MIX button.
4 To return to normal viewing press the TV button.
33
ENG
ENG
Selecting a Specific Teletext Page
Press the number buttons on the remote control to enter the page number directly:
1 Enter the three-digit page number listed in the contents by pressing the corresponding numeric buttons.
Result: The current page counter is incremented and the page is then displayed.
2 If the selected page is linked with several secondary pages, the secondary pages are displayed in sequence. To freeze the display on a given page, press the HOLD ( ). Press the HOLD again to resume.
3 Using the various display options:
To display...
◆ Both teletext information and the normal broadcast
◆ Hidden text
(answers to quiz games, for example)
◆ The normal screen
◆ A secondary page, by entering its 4-digit number
◆ The next page
◆ The previous page
◆ Double-size letters in the:
• Upper half of the screen
• Lower half of the screen
◆ Normal screen
Press the...
TTX/MIX
REVEAL ( )
REVEAL ( ) again
SUB-PAGE ( )
PAGE UP ( )
PAGE DOWN ( )
SIZE ( )
◆ Once
◆ Twice
◆ Three times
34
Using FLOF to Select a Teletext Page
The various topics included in the teletext pages are color-coded, and can be selected by pressing the colored buttons on the remote control.
1 Display the teletext contents page by pressing the TTX/MIX button.
2 Press the colored button corresponding to the topic that you wish to select (The available topics are listed on the status information line).
Result: The page is displayed with additional color-coded information that can be selected in the same way.
3 To display the:
Previous page
Next page
Press the:
Red button.
Green button.
4
When you have finished, press the TV button to return to the normal broadcast.
Storing Teletext Pages
Up to four teletext pages can be stored.
1 Select the LIST mode.
Result: Four 3-digit numbers are displayed in different colors at the bottom of the screen.
2 Press the colored button corresponding to the page that will be replaced.
3 Enter the new page number using the numeric buttons.
4 Repeat steps 2 and 3 for each page to be stored, using a different colored button each time.
5 Press the STORE ( ) button until the corresponding blocks are displayed in white.
➣
The LIST ( ) button is used to switch between:
◆ LIST mode
◆ FLOF mode
35
ENG
ENG
Connecting to the AV-1 or 2 Input/Outputs
➣
These figures show typical connector-jack panels.
The actual configuration on your TV may be different, depending on your model.
➢
AV-1 is used for equipment with an RGB output, such as video game devices and video disc players or a VCR.
Rear of TV AV cable
MONITOR
-OUT
VIDEO
(MONO)
L-AUDIO-R
INPUT 2
INPUT 1 or
VCR
Decoder/
Video game device
Video disc player
Camcorder
2 or
Satellite receiver
RGB
1
Connecting to the S-VIDEO Input
(depending on the model)
Side of TV
➢
The S-VIDEO/RCA (AUDIO-L and R) connectors are used for equipment with an S-Video output, such as a camcorder or VCR.
and
Camcorder
VCR
Front of TV
36
Connecting to the DVD Input (Option)
➢
The DVD/RCA (AUDIO-L and R) connectors are used for equipment with a DVD output.
Rear of TV
MONITOR
-OUT
VIDEO
(MONO)
L-AUDIO-R
INPUT 2
INPUT 1
DVD
ENG
Connecting to the RCA Input
(depending on the model)
Side of TV
➢
The RCA (VIDEO + AUDIO-L and R) connectors are used for equipment such as camcorders, video disc players and some video game devices.
Camcorder
Front of TV
Video disc player
Decoder/
Video game device
37
ENG
Connecting Headphones
You can connect a set of headphones to your television if you wish to watch a television programme without disturbing the other people in the room.
1
Plug a set of headphones into the 3.5 mm mini-jack socket of the television.
Result: The sound is heard through the headphones.
2
When you wish to hear the sound through the speakers again, simply disconnect the headphones.
➢
Prolonged use of headphones at a high volume may damage your hearing.
Viewing Pictures From External Sources
Once you have connected up your various audio and video systems, you can view the different sources by selecting the appropriate input.
1 Check that all the necessary connections have been made.
2 Switch the television on and if necessary, press the VIDEO button one or more times until the required input is displayed.
➢
Depending on the source selected, the pictures may appear automatically.
➢
To watch television programmes again, press the TV button and select the number of the channel required.
38
Automatic Degaussing to Remove Colour Patches
A degaussing coil is mounted around the picture tube, so you do not normally need to degauss the television manually.
If you move the television to a different position and color patches appear on the screen, you must:
◆ Switch the television off by pressing the “POWER ” (ON/OFF) button on the front panel
◆ Unplug the television from the wall socket
◆ Leave the television power-off (stand-by) for about 30 minutes so that the automatic degauss function can be activated, and then press the POWER button on the remote control.
☛
If your television will be left unattended, press the “POWER ” (ON/OFF) button to turn your television off.
ENG
Troubleshooting: Before Contacting Service Personnel
Before contacting Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of the television and contact your local dealer.
No sound or picture
Normal picture but no sound
No picture or black and white picture
Sound and picture interference
Blurred or snowy picture, distorted sound
Remote control malfunctions
◆ Check that the mains lead has been connected to a wall socket.
◆ Check that you have pressed the “POWER ” (ON/OFF) button.
◆ Check the picture contrast and brightness settings.
◆ Check the volume.
◆ Check the volume.
◆ Check whether the MUTE button has been pressed on the remote control.
◆ Adjust the colour settings.
◆ Check that the broadcast system selected is correct.
◆ Try to identify the electrical appliance that is affecting the television and move it further away.
◆ Plug your television into a different mains socket.
◆ Check the direction, location and connections of your aerial.
This interference is often due to the use of an indoor aerial.
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check the battery terminals.
39
- AFTER SALES SERVICE
- Do not hesitate to contact your retailer or service agent if a change in the performance of your product indicates that a faulty condition may be present.
ELECTRONICS
AA68-01015D-03
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement