M74HC04
Hex inverter
DIP14 SO14 TSSOP14
Datasheet
-
production data
Description
The M74HC04 is a high-speed CMOS hex inverter manufactured using silicon gate C
2
MOS technology.
The internal circuit is composed of 3 stages including a buffer output which enables high noise immunity and stable output.
All inputs are equipped with protection circuits to guard against static discharge and transient excess voltage.
Features
High speed: t
PD
= 8 ns (typ.) at V
CC
= 6 V
Low power dissipation:
I
CC
= 1 μA (max.) at T
A
= 25 °C
High noise immunity:
V
NIH
= V
NIL
= 28% V
CC
(min.)
Symmetrical output impedance:
|I
OH
| = I
OL
= 4 mA (min) at V
CC
= 4.5 V
Balanced propagation delays: t
PLH
@ t
PHL
Wide operating voltage range:
V
CC
(OPR) = 2 V to 6 V
Pin and function compatible with 74 series 04
ESD performance
– CDM: 1 kV
– HBM: 2 kV
– MM: 200 V
Order code
Table 1. Device summary
Temperature range Package Packaging Marking
M74HC04B1R
M74HC04YRM13TR
M74HC04RM13TR
M74HC04TTR
M74HC04YTTR
(1)
(1)
-55 °C to +125 °C
-40 °C to +125 °C
-55 °C to +125 °C
-55 °C to +125 °C
DIP14
SO14 (automotive grade)
SO14
TSSOP14
Tube
Tape and reel
Tape and reel
Tape and reel
-40 °C to +125 °C TSSOP14 (automotive grade) Tape and reel
M74HC04B1
74HC04Y
74HC04
HC04
HC04Y
1. Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC
Q001 and Q002 or equivalent.
September 2013
This is information on a product in full production.
DocID001882 Rev 3 1/13
www.st.com
3
4
1
2
Contents
Contents
5
M74HC04
Pin information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.1
DIP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2
SO14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3
TSSOP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2/13 DocID001882 Rev 3
M74HC04
Figure 1. Pin connections and IEC logic symbols
Pin information
Pin number
1, 3, 5, 9, 11, 13
2, 4, 6, 8, 10, 12
7
14
Table 2. Pin description
Symbol
1A to 6A
1Y to 6Y
GND
V
CC
Name and function
Data inputs
Data outputs
Ground (0 V)
Positive supply voltage
DocID001882 Rev 3 3/13
13
Functional description
Table 3. Truth table
A
L
H
Figure 2. Input and output equivalent circuit
Y
H
L
M74HC04
4/13 DocID001882 Rev 3
M74HC04 Electrical characteristics
Stressing the device above the ratings listed in the “Absolute maximum ratings” table may cause permanent damage to the device. These are stress ratings only, and operation of the device at these or any other conditions above those indicated in the operating sections of this specification are not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Symbol
Table 4. Absolute maximum ratings
Parameter Value Unit
V
CC
V
I
V
O
I
IK
I
OK
I
O
I
CC or
I
GND
P
D
T stg
T
L
Supply voltage
DC input voltage
DC output voltage
DC input diode current
DC output diode current
DC output current
DC V
CC
or ground current
Power dissipation
Storage temperature
Lead temperature (10 sec)
-0.5 to +7
-0.5 to V
500
CC
-0.5 to V
CC
±20
±20
±25
±50
(1)
+0.5
+0.5
-65 to +150
1. 500 mW at 65 °C; derate to 300 mW by 10 mW/°C from 65 °C to 85 °C
300 mA mA mA mW
V
V
V mA
°C
°C
Symbol
V
CC
V
I
V
O
T op t r
, t f
Table 5. Recommended operating conditions
Parameter Value
Supply voltage
Input voltage
Output voltage
Operating temperature
Input rise and fall time
V
CC
= 2.0 V
V
CC
= 4.5 V
V
CC
= 6.0 V
2 to 6
0 to V
CC
0 to V
CC
-55 to 125
0 to 1000
0 to 500
0 to 400
Unit
°C ns ns ns
V
V
V
DocID001882 Rev 3 5/13
13
Electrical characteristics M74HC04
Symbol Parameter V
CC
(V)
V
IH
V
IL
V
OH
V
OL
I
I
I
CC
High-level input voltage
Low-level input voltage
High-level output voltage
Low-level output voltage
Input leakage current
Quiescent supply current
2.0
4.5
6.0
4.5
6.0
4.5
6.0
4.5
6.0
2.0
4.5
6.0
2.0
2.0
4.5
6.0
6.0
6.0
Table 6. DC specifications
Test condition
I
O
= -20 μA
I
O
= -20 μA
I
O
= -20 μA
I
O
= -4.0 mA
I
O
= -5.2 mA
I
O
= 20 μA
I
O
= 20 μA
I
O
= 20 μA
I
O
= 4.0 mA
I
O
= 5.2 mA
V
I
= V
CC
GND or
V
I
= V
CC
GND or
Value
T
A
= 25°C
-40 to 85°C -55 to 125°C
Min.
Typ.
Max.
Min.
Max.
Min.
Max.
1.5
3.15
4.2
0.5
1.35
1.8
1.9
4.4
5.9
2.0
4.5
6.0
4.18
4.31
5.68
5.8
0.0
0.0
0.1
0.1
0.0
0.1
0.17
0.26
0.18
0.26
1.5
3.15
4.2
1.9
4.4
5.9
4.13
5.63
0.5
1.35
1.8
0.1
0.1
0.1
0.33
0.33
1.5
3.15
4.2
1.9
4.4
5.9
4.10
5.60
0.5
1.35
1.8
0.1
0.1
0.1
0.40
0.40
0.1
1
1
10
1
20
Unit
V
V
V
V
μA
μA
6/13 DocID001882 Rev 3
M74HC04 Electrical characteristics
t fLH t fHL
Output transition time t
PLH t
PHL
Propagation delay time
2.0
4.5
6.0
2.0
4.5
6.0
Table 7. AC electrical characteristics
(C
L
= 50 pF, input t r
= t f
= 6 ns)
Test condition Value
Symbol Parameter V
CC
(V)
T
A
= 25°C
-40 to 85°C -55 to 125°C
Min.
Typ.
Max.
Min.
Max.
Min.
Max.
45
9
8
38
8
6
75
15
13
95
19
16
95
19
16
120
24
20
110
22
19
145
29
25
Unit
ns ns
Table 8. Capacitive characteristics
Test condition Value
T
A
= 25°C
-40 to 85°C -55 to 125°C
Symbol Parameter
V
CC
(V) Unit
Min.
Typ.
Max.
Min.
Max.
Min.
Max.
C
C
IN
PD
Input capacitance
Power dissipation capacitance
(1)
5.0
5.0
5
22
10 10 10 pF pF
1. CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to the test circuit). Average operating current can be obtained by the following equation:
I
CC(opr)
= C
PD
x V
CC
x f
IN
+ I
CC
/6 (per gate)
DocID001882 Rev 3 7/13
13
Electrical characteristics
Figure 3. Test circuit
M74HC04
Figure 4. Waveforms: propagation delay times (f = 1 MHz; 50% duty cycle)
8/13 DocID001882 Rev 3
M74HC04 Package information
4.1
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK
®
packages, depending on their level of environmental compliance. ECOPACK
® specifications, grade definitions and product status are available at:
www.st.com
.
ECOPACK
®
is an ST trademark.
DIP14 package information
Figure 5. Plastic DIP14 package mechanical outline
Dimension
E e b1
D a1
B b
I
L e3
F
Z
Min.
0.51
1.39
Table 9. Plastic DIP14 package mechanical data mm.
inches
Typ Max.
Typ.
1.65
Min.
0.020
0.055
0.5
0.25
0.020
0.010
20
8.5
2.54
15.24
0.335
0.100
0.600
7.1
5.1
3.3
0.130
1.27
2.54
0.050
Max.
0.065
0.787
0.280
0.201
0.100
DocID001882 Rev 3 9/13
13
Package information
4.2 SO14 package information
Figure 6. Plastic SO14 package mechanical outline
M74HC04
Ref.
10/13
L
M
F
G
S e e3
D
E b b1
C c1
A a1 a2
Min.
0.1
0.35
0.19
8.55
5.8
3.8
4.6
0.5
Table 10. SO14 package mechanical data mm.
Typ Max.
Min.
inches
Typ.
0.5
1.75
0.2
1.65
0.46
0.25
0.003
0.013
0.007
8.75
6.2
45° (typ.)
0.336
0.228
0.019
1.27
7.62
0.050
0.300
4.0
5.3
1.27
0.68
8° (max.)
0.149
0.181
0.019
DocID001882 Rev 3
0.344
0.244
0.157
0.208
0.050
0.026
Max.
0.068
0.007
0.064
0.018
0.010
M74HC04
4.3 TSSOP14 package information
Figure 7. TSSOP14 package mechanical outline
Package information
Ref.
c
D
E
E1
A
A1
A2 b e
K
L
Min.
0.05
0.8
0.19
0.09
4.9
6.2
4.3
0°
0.45
Table 11. TSSOP14 package mechanical data mm.
inch es
Typ Min.
Typ.
1
5
6.4
4.4
0.65 BSC
Max.
0.20
5.1
6.6
4.48
1.2
0.15
1.05
0.30
0.002
0.031
0.007
0.004
0.193
0.244
0.169
0.004
0.039
0.197
0.252
0.173
0.0256 BSC
0.60
8°
0.75
0°
0.018
0.024
Max.
0.047
0.006
0.041
0.012
0.0089
0.201
0.260
0.176
8°
0.030
DocID001882 Rev 3 11/13
13
Revision history M74HC04
Date
11-Sep-2013
Revision
Table 12. Document revision history
Changes
3
Added ESD information to
Features
Added automotive grade order codes, temperature ranges, and marking information to
Table 1: Device summary
Revised document presentation
Minor textual updates
12/13 DocID001882 Rev 3
M74HC04
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE
IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH
PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR
ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED
FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN
WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE,
AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS.
PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE
CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2013 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
DocID001882 Rev 3 13/13
13
