Toshiba 27AF61 Flat Panel Television User Manual

FIELD REPLACEABLE UNIT DOCUMENTATION
Portege’
3010/3020CT
BATTERY PACK REMOVAL OPTIONAL PCMCIA CARD REMOVAL
Release lever
Battery Pack
PC éard Eject Lever
1. Turnthe computer upside down as shown
2. Slide the battery release lever inthe direction ofthe 1.Pullout the eject lever ofthe PC card to be removed.
arrow 2.Pushthe eject lever toremove the PC card.
3. Pull the battery pack slightly forward and lit
it out.
EXPANSION MEMORY REMOVAL MEMBRANE/IPS SWITCH REMOVAL
Memory
cover
M2x3 flat
head black
1. Turnthe computer upside down. 1.R i ing the |
emove x ack screws s=curing the cover.
memory cover.
3. Grasp both sides ofthe memory module and pull it out.
TOSHIBA
Tough Enough for Today's World.
FIELD REPLACEABLE UNIT DOCUMEN
Portege"
3010/3020CT
MEMBRANEAPS SWITCH REMOVAL
Membrane switch
E
yo = head
silver
2. Turn the a right side up and lit up the 4. Remove LED lens.
almrest c 5. Remove three M2x3 flat head silver screws
3. Release the PS cable by Ea the connector securing the IPS bracket.
P11 and remove the palmrest с: 6. Remove the membrane switch and the IP S switch.
HDD/SUB BOARD REMOVAL
KEYBOARD REMOVAL
& ; USB earth
ai Bm PJ27 Coppertape HDD Plate/SUB board
1. Disconnect the sound cable Ш an PITO.
1. Release the lock ofPJ10 ctor and pull out th 2.Р соррег the HDD
a able” END dobbs % and removethe mylar cable from PJ20.
2. Release the == of PJ9 connector and pull out the 3. Remove one M2xd brass rare ing the USB
IPS switch c earth plate / SUB board and li
3. Lift out the Keyboard 4. Disconnect the HDD fom PJ27 and slick it ot ofthe
: : HDD insulator.
TOSHIBA
Tough Enough for Todays Word.
FIELD REPLACEABLE UNIT DOCUMENTATION
Portege’
3010/3020CT
DISPLAY ASSEMBLY REMOVAL
LCD cable PJ3
M2x6 flat head black screws
M2x4 brass screws
2. Disconnect the microphone cable from PJ15 and
1. Remove two M2x6 flat head black screws LCD cable from PJ3.
securingthe display assembly. 3. Remove six M2x4 brass screws securing the
display assembly.
RTC BATTERY REMOVAL SYSTEM BOARD REMOVAL
LCD cover sensor lever M2x6 Silver screw
1. Remove two M2x4 brass screws securing
RTC bétterycable PJ12 Insulator
1. Disconned the speaker cable from PJ16. the
2. Disconnect the RTC battery cable from PJ12. 2. Remove sound cable from PJ17.
3. Remove the insulator and then the RTC battery. 2. Remove one M2x6 silver screw securin
sensor lever and lift out te system board.
MOTE: The Heat conductors are separate parts. Please
remove them before sending the board to TOSHIBA,
to the replacement board to prevent it rom overheating.
TOSHIBA
Tough Enough for Today's World.
FIELD REPLACEABLE UNIT DOCUMENTATION
Portege’
3010/3020CT
SYSTEM BOARD REMOVAL MICROPHONE REMOVAL
PCMCIA
slot cable
Microphone
insulator
PCMCIA slot Microphone
3. Turn the system board upside down, release the lock of 1. Peel off the microphone insulator.
omc. sot cable and disconned it fom PJ6 on the 2.R tt icroph holder and th icroph
syster
4. ea he PCMCIA dot and remove it. FL INVERTER AND LCD REMOVAL
DISPLAY MASK REMOVAL К а
FL
cable
FL
inverter
M2x4
flat head
LCD cable LED module Fl inverter cable
1. Remove one M2x4 flat head silver screw securing
Display mask inverter board.
2. Lift upthe FL inverter board and disconnect the FL
1. en four mask seals using a pair of fine-tipped cable from CH2 andthe FL inverter cable from CH1
tue 3. Remove three M2x3 flat head
M2x5 flat head screwsílower side) securing the LCD module.
and two M2x4 flat hea screwsi(upper side). 4. Carefully rotate the LCD module from right to left of
3. There are 10 he securi MA the display mask. h cover and removethe clip securing the LCD.
Cereb insert yo! 5.D LCD cable from the LCD module and
e LCD panel and pry open the display ‘mask. Г.
remove the LCD from the compute
TOSHIBA
Tough Enough for Today's World.