advertisement
VIDEO CASSETTE RECORDER
HR-VP830U
POWER
A B
1
4
7
C.RESET
CANCEL
CH SKIP
2
5
DAILY (M–F)
8
AUX
0
TV
VOL.
CH
SP/EP DISPLAY TV/VIDEO CABLE
TV
PLAY
REW
FF
VCR
REC
C.M
EMOR
Y
ADD
MEN
U
STOP
PAUSE
SKIP SEAR
CH
OK
ENTER
OSD
3
6
WEEKLY
9
TIMER
TIME
SCAN
ILLUMI GUIDE
MULTI BRAND
REMOTE CONTROL UNIT
POWER
MENU dB
L
–20 15 10 8 6 4 2 0 2 4 6 +8
I T R
VIDEO
TIMER
SP
AM
M EP PM H
dB
R
–20 15 10 8 6 4 2 0 2 4 6 +8
M S
ST
SAP
R E C
PLAY
PAUSE
CH
OK
PLAY
REW
SE
AR
CH
SLO
W
8
SLOW
SE
AR
C
H
FF
STOP/EJECT
REW FF
w Cable Channel
Changer
INSTRUCTIONS
For Customer Use:
Enter below the Serial No. which is located on the rear of cabinet. Retain this information for future reference.
Model No. HR-VP830U/U(C)
Serial No.
PU30425-1820
2
Dear Customer,
Thank you for purchasing the JVC VHS video cassette recorder. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of your new VCR.
CAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
CAUTION:
This video cassette recorder should be used with AC
120V`, 60Hz only.
To prevent electric shocks and fire hazards, DO NOT use any other power source.
Failure to heed the following precautions may result in damage to the VCR, remote control or video cassette.
1. DO NOT place the VCR . . .
... in an environment prone to extreme temperatures or humidity.
... in direct sunlight.
... in a dusty environment.
... in an environment where strong magnetic fields are generated.
... on a surface that is unstable or subject to vibration.
2. DO NOT block the VCR’s ventilation openings.
3. DO NOT place heavy objects on the VCR or remote control.
4. DO NOT place anything which might spill on top of the
VCR or remote control.
5. AVOID violent shocks to the VCR during transport.
**MOISTURE CONDENSATION
Moisture in the air will condense on the VCR when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form on the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the VCR’s power turned on for a few hours to let the moisture dry before inserting a tape.
**ABOUT HEAD CLEANING
Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or interrupted. Be sure to contact your nearest JVC dealer if such troubles occur.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE
LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU'AU FOND.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
VCR Plus+C
3
and PlusCode are trademarks of Gemstar Development Corporation.
The VCR Plus+C
3
system is manufactured under licence from
Gemstar Development Corporation.
DSS TM is an official trademark of DIRECTV, Inc., a unit of GM
Hughes Electronics .
CAUTION:
Changes or modifications not approved by JVC could void user's authority to operate the equipment.
n Cassettes marked "VHS" (or "S-VHS") can be used with this video cassette recorder. However, only "VHS" recordings can be played back in this model.
n HQ VHS is compatible with existing VHS equipment.
IMPORTANT PRODUCT
SAFETY INSTRUCTIONS
Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing.
ATTENTION:
Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety, please read all the safety and operating instructions before you operate this product and keep this booklet for future reference.
5. Ventilation
Slots and openings in the cabinet are provided for ventilation.
To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.
• Do not block the openings by placing the product on a bed, sofa, rug or other similar surface.
• Do not place the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
INSTALLATION
1. Grounding or Polarization
(A) Your product may be equipped with a polarized alternatingcurrent line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way.
This is a safety feature.
If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
(B) Your product may be equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
2. Power Sources
Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions.
3. Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
4. Power Cord Protection
Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
ANTENNA INSTALLATION
INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
2. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.
3. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN WIRE
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION
810-20)
ELECTRIC SERVICE
EQUIPMENT
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
3
4
USE
1. Accessories
To avoid personal injury:
• Do not place this product on an unstable cart, stand, tripod, bracket, or table. It may fall, causing serious injury to a child or adult, and serious damage to the product.
• Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product.
• Use a mounting accessory recommended by the manufacturer and follow the manufacturer’s instructions for any mounting of the product.
• Do not try to roll a cart with small casters across thresholds or deep-pile carpets.
2. Product and Cart Combination
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
PORTABLE CART WARNING
(Symbol provided by RETAC)
3. Water and Moisture
Do not use this product near water—for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the like.
4. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or shortout parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
5. Attachments
Do not use attachments not recommended by the manufacturer of this product as they may cause hazards.
6. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
7. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
SERVICING
1. Servicing
If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions, do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a.When the power supply cord or plug is damaged.
b.If liquid has been spilled, or objects have fallen into the product.
c.If the product has been exposed to rain or water.
d.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.
e.If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance—this indicates a need for service.
3. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
4. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating condition.
HOW TO USE THIS INSTRUCTION
MANUAL
● All major sections and subsections are listed in the Table Of
Contents on page 5. Use this when searching for information on a specific procedure or feature.
● The Index on pages 67–69 lists frequently-used terms, and the number of the first page on which they are used or explained in the manual. This section also illustrates the controls and connections on the front and rear panel, the front display panel and the remote control.
● The
Z
mark signals a reference to another page for instructions or related information.
● Operation buttons necessary for the various procedures are clearly indicated through the use of illustrations at the beginning of each major section.
BEFORE YOU INSTALL YOUR NEW
VCR . . .
. . . please read the sections/literature listed below.
● ”Cautions” on page 2
● ”Important Products Safety Instructions” on the previous pages
CONTENTS
I
NSTALLING YOUR NEW VCR 6
Basic Connections ..................................6
I
NITIAL SETTINGS
Dual Quick Set .............................................. 7
Language ..................................................... 8
Clock ............................................................ 9
7
Preparation ................................................................9
Semi-Auto ................................................................10
Manual .................................................................... 11
Auto ........................................................................ 11
Tuner .......................................................... 12
Set Receivable Channels .......................................... 12
Add Or Delete A Channel ........................................ 14
Cable Box Control ....................................... 15
Situate And Connect Controller ............................... 15
Set Cable Box Output Channel ................................ 16
Set Cable Box Brand ................................................17
VCR Plus+ Setup ......................................... 19
DSS Receiver Control ................................... 22
Situate And Connect Controller ............................... 22
Set DSS Receiver Output Channel ........................... 23
Set DSS Receiver Brand ........................................... 24
S
IMPLE PLAYBACK AND
RECORDING 25
Simple Playback ......................................... 25
Simple Recording ........................................ 26
P
LAYBACK AND RECORDING
FEATURES 27
Playback .................................................... 27
Still Picture/Frame-By-Frame Playback ..................... 27
Slow Motion/Reverse Slow Motion .......................... 27
Manual Tracking ......................................................28
Select The Soundtrack .............................................29
Superimpose ............................................................30
Index Search ............................................................31
Manual Index Mark/Erase ........................................31
Repeat Playback ......................................................31
Instant ReView .........................................................32
Counter Reset ..........................................................32
Counter Memory .....................................................32
Tape Position Indicator ............................................33
Next-Function Memory ............................................33
AV COMPU LINK Playback ..................................... 33
Time Scan ................................................... 35
High-Speed Search (7 x playback) ........................... 35
Variable-Speed Search/Reverse Play ........................ 35
Skip Search ..............................................................36
Time Scan Audio .....................................................37
Active Video Calibration.............................. 38
Preparation ..............................................................38
Recording ................................................................39
Playback ..................................................................40
Recording ................................................... 41
Record One Program While
Watching Another ....................................................41
Display Elapsed Recording Time .............................. 41
Stereo And SAP (Second Audio Program) ................. 42
To Record SAP Programs ..........................................42
Hi-Fi Audio Recording Level Control ....................... 43
T
IMER RECORDING 44
VCR Plus+ Timer Programming .................... 44
On-Screen Timer Programming ........... 46
Check And Cancel Programs ................................... 48
Auto Timer ......................................................49
Instant Timer Recording (ITR) ....................... 50
E
DITING 51
Edit To Or From Another VCR ....................... 51
Edit From A Camcorder ............................... 52
Assemble Editing ........................................ 54
Audio Dubbing ........................................... 55
Insert Editing .............................................. 56
Random Assemble Editing ........................... 58
S
PECIAL FEATURES 60
TV Multi-Brand Remote Control .............................. 60
Cable Box Multi-Brand Remote Control ................... 61
Control Two JVC VCRs ............................................62
Child Lock ...............................................................62
T
ROUBLESHOOTING 63
Power ........................................................ 63
Tape Transport ............................................ 63
Playback .................................................... 63
Recording ................................................... 64
Timer Recording .......................................... 64
Other Problems. ......................................... 65
Q
UESTIONS AND ANSWERS 66
Playback .................................................... 66
Recording ................................................... 66
Timer Recording .......................................... 66
I
NDEX 67
List Of Terms ............................................... 67
Front View .................................................. 68
Rear View .................................................. 68
Front Display Panel ..................................... 69
Remote Control ........................................... 69
S
PECIFICATIONS
F
OR SERVICING
W
ARRANTY
70
71
72
5
6
Basic
Connections
Antenna or Cable
AC Power
Cord
Coaxial Cable
Flat Feeder
Back of VCR
AC
Outlet
Video Cable
(supplied)
Audio Cable
(supplied)
RF Switch
TV
Matching Transformer
(Not supplied)
Back of VCR
75 ohm terminal
RF OUT
CH4
CH3 OFF
ANTENNA-
IN (Antenna or Cable input)
RF
OUT
RF Cable
(supplied)
INSTALLING YOUR NEW VCR
1
CHECK CONTENTS
Make sure the package contains all of the accessories listed in “SPECIFICATIONS” (
Z
pg. 70).
SITUATE VCR
Place the VCR on a stable, horizontal surface.
2
3
4
5
CONNECT VCR TO TV
The connection method you use depends on the type of
TV you have.
RF Connection
● To Connect To A TV With NO AV Input Terminals . . .
a– Disconnect the TV antenna from the TV.
b– Connect the TV antenna cable to the ANT IN jack on the rear of the VCR.
c– Connect the supplied RF cable between the RF
OUT jack on the rear of the VCR and the TV’s antenna terminal.
AV Connection
● To Connect To A TV With AV Input Terminals . . .
a– Connect the antenna, VCR and TV as shown in the illustration.
b– Connect an Audio/Video Cable between the AUDIO
OUT and VIDEO OUT jacks on the rear of the VCR and the AV IN jacks on the TV.
CONNECT VCR TO
POWER SOURCE
Connect the power plug to an AC outlet.
● The clock and tuner will automatically be set when the antenna is connected and when the AC is first connected to the VCR (
Z
pg. 7).
FINAL PREPARATION FOR
USE
Select the VCR channel (3, 4 or OFF) by setting the RF switch on the rear of the VCR as shown in the illustration.
Z
NOTES below.
Turn on the power to the TV. You are now able to perform simple playback (
Z
pg. 25) and recording (
Z
pg. 26).
(If 'Auto' is displayed on the front display panel, the clock is being set automatically. Wait for the time to be displayed before powering on the VCR.)
NOTES:
● The VCR channel is the channel on the TV which will display the audio and video signals from the VCR.
● The RF switch is preset to the CH3 position.
Set to CH4 if you use the RF connection and CH3 is used for broadcasting in your area. If you use the AV connection, set the RF switch to OFF.
● If your TV has no AV input terminals, set the channel on the
TV to correspond to the RF switch on the back of the VCR.
● Even if your TV has AV input terminals, you must connect it to the VCR using an RF cable in order to record one show while watching another (
● For full identification of the VCR's rear panel, refer to the
Index (REAR VIEW
Z
Z
pg. 41).
pg. 68).
INITIAL SETTINGS
Dual Quick Set
Auto Clock Set/Auto Tuner Set
•
•
•
•
•
•
•
•
•
8
IMPORTANT
● Don’t press any buttons on the VCR or remote during
Dual Quick Set.
● If you perform Dual Quick Set successfully, there’s no need to perform the Clock (
Z
pg. 9) and Tuner (
Z
pg. 12) procedures. If, however, you want to add or delete channels, refer to “Add Or Delete A Channel” on page 14.
ATTENTION CABLE BOX SUBSCRIBERS
If you perform the Dual Quick Set procedure . . .
● Select the PBS channel on your cable box before plugging your VCR’s power plug into the AC outlet. (If you have more than one PBS channel, you may have to select an alternative PBS channel if Dual Quick Set is not successful.)
● If there is no PBS channel in your area, perform the
Manual Clock Set procedure (
Z
pg. 11).
● For automatic clock adjustment to take place the VCR's power must be off and the cable box must be set to the
PBS channel at clock adjustment times.
● If you perform Dual Quick Set successfully, D.S.T. will be set to “AUTO”. At the D.S.T. adjustment time (
Z
pg. 11), your VCR's power must be off and your cable box must be set to the host PBS channel in your area for the D.S.T.
adjustment to take place. If the clock is not set correctly, change the D.S.T. setting to “ON” or “OFF. See step 9 of
Semi-Auto procedure (
Z
pg. 10) or step 6 of Manual procedure (
Z
pg. 11).
NOTE:
If, due to a power outage or other event, the memory backup fails,
Dual Quick Set is performed when power is restored to the VCR.
Dual Quick Set sets the clock and tuner channels automatically when power is first connected to the VCR. The antenna cable must be connected for dual quick set.
The time and date can be set automatically from clock setting data that is transmitted by one of the regular TV broadcast channels. We call this TV channel the “Host Channel” and it is a PBS channel in your area.
1
PERFORM DUAL QUICK SET
Make sure that the antenna cable is connected to the
VCR. Then connect the VCR’s power plug to an AC outlet. For connection configuration, refer to “Basic
Connections” (
Z
pg. 6). The clock and tuner channels will automatically be set.
● Auto clock set is performed first. The auto clock set function scans all the channels received by your VCR to find the Host Channel and then sets the clock.
AUTO is displayed on the front display panel during
Auto clock set.
● Auto channel is performed next. The auto channel set function scans all the channels that are receivable by your VCR. It then automatically assigns each receivable channels to the CH▲▼ buttons. It skips non-receivable channels. During auto channel set the channel numbers are displayed in ascending order.
● When Dual Quick Set has been completed successfully the correct time is displayed.
● If "AUTO CLOCK SET" or "SEMI-AUTO CLOCK SET" is selected at the Override Auto Clock Set screen on page 10, the clock will be adjusted automatically by the Host PBS every hour on the hour (except for
11:00 PM, midnight, 1:00 AM and 2:00 AM) by the incoming PBS channel clock setting data. (This automatic clock adjustment can only be performed when the VCR’s power is turned off. The clock will be adjusted on the hour based on the time displayed on the VCR, not on the actual real time.) The default setting is "AUTO CLOCK SET".
● If an incorrect time is displayed on the front display panel, you may be receiving the clock setting data of a PBS channel from an adjacent time zone, or an incorrect PBS channel from a cable TV system. In this case, perform the Semi-Auto procedure (
Z
pg. 10).
Auto channel set has already taken place and it need not be set again.
● If “- -:- -” appears on the display, your antenna cable may not be connected to the VCR, there may not be a
Host PBS signal available in your area, or your cable box may not be set to the PBS channel. If the antenna connection or cable box setting is incorrect, connect the antenna cable to the VCR or select the correct cable channel. Then power on and power off the VCR; the
Dual Quick set mode will be automatically reactivated and "Auto" will be displayed on the VCR's front panel. If everything is connected and set correctly, perform the
Manual Clock Set procedure (
Z
pg. 11). Auto channel set has not yet taken place, so please also perform the
“Set Receivable Channels” procedure (
Z
pg. 12).
7
During Initial Auto Clock Set During Auto Channel Set
The channels appear in ascending order, beginning with 1.
PM
Dual Quick Set Completed
The current time (including
AM/PM) is displayed.
8
Language
•
•
•
•
•
•
•
•
•
•
MENU
POWER
1
4
7
2
5
8
0
3
6
9
CH
5∞
OK
TIME SCAN
5∞
8
INITIAL SETTINGS (cont.)
This VCR offers you the choice to view on-screen messages in
English, Spanish or French (not including messages superimposed on the TV picture). Select the desired language using this procedure. The default setting is "ENGLISH".
1
TURN ON THE VCR
Press POWER.
2
ACCESS ON-SCREEN
MENU
Press MENU as many times as necessary to bring up the
Main Menu screen.
3
ACCESS CUSTOM SET
SCREEN
At the Main Menu screen, place the arrow next to
“CUSTOM SET” by pressing CH
5∞ or TIME
SCAN
5∞, then press OK.
MAIN MENU
PROGRAM SET
FUNCTION SET
TUNER SET
=CUSTOM SET
VIDEO CALIBRATION
R.A. EDIT
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
4
ACCESS LANGUAGE
SELECT SCREEN
The messages are preset to appear in English. If you want to see them in Spanish or
French, place the arrow next to “LANGUAGE SELECT” by pressing CH
5∞ or TIME
SCAN
5∞, then press OK.
CUSTOM SET
OVERRIDE
AUTO CLOCK SET
=LANGUAGE SELECT
VCR PLUS+ SET-UP
DSS RECEIVER OUTPUT
DSS RECEIVER BRAND SET
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
5
SELECT LANGUAGE
At the Language Select screen, place the arrow next to the desired language by pressing
CH
5∞ or TIME SCAN
5∞, then press MENU as many times as necessary to return to the normal screen.
LANGUAGE SELECT
=ENGLISH
ESPAÑOL
FRANCAIS
PRESS (
5,∞) TO SELECT
PRESS (MENU) TO END
Clock
•
•
•
•
•
•
•
•
•
MENU
1
4
7
2
5
8
0
3
6
9
CH
POWER
8
Perform clock setting only if the clock has not been set correctly by Dual Quick Set. Access the Override Auto Clock Set screen to choose the Auto, Semi-Auto or Manual clock setting procedure. Each procedure starts from step 5. *Auto need only be selected if Semi-Auto or Manual had previously been selected.
9
Preparation
TURN ON THE VCR
Press POWER.
1
2
ACCESS ON-SCREEN
MENU
Press MENU as many times as necessary to bring up the Main Menu screen.
3
ACCESS CUSTOM SET
SCREEN
At the Main Menu screen, place the arrow next to
“CUSTOM SET” by pressing CH
5∞ or TIME
SCAN
5∞, then press OK.
MAIN MENU
PROGRAM SET
FUNCTION SET
TUNER SET
=CUSTOM SET
VIDEO CALIBRATION
R.A. EDIT
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
4
ACCESS CLOCK SET MODE
SELECT SCREEN
Place the arrow at the
Custom Set screen next to
“OVERRIDE AUTO
CLOCK SET” by pressing
CH
5∞ or TIME SCAN
5∞, then press OK.
CUSTOM SET
=OVERRIDE
AUTO CLOCK SET
LANGUAGE SELECT
VCR PLUS+ SET-UP
DSS RECEIVER OUTPUT
DSS RECEIVER BRAND SET
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
OK
TIME SCAN
10
•
•
•
•
•
•
•
•
•
•
NUMBER
1
4
7
2
5
8
0
3
6
9
CH
MENU
OK
TIME SCAN
8
INITIAL SETTINGS (cont.)
Semi-Auto
5
SELECT MODE
At the Override Auto
Clock Set screen, place the arrow next to “SEMI-
AUTO CLOCK SET” by pressing CH▲▼ or TIME
SCAN
5∞, then press OK.
OVERRIDE AUTO CLOCK SET
AUTO CLOCK SET
=SEMI-AUTO CLOCK SET
MANUAL CLOCK SET
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
6
7
ACCESS SELECT SCREENS
At the Semi-Auto Clock Set screen, place the arrow next to the desired mode by pressing CH▲▼ or TIME SCAN
5∞, then press OK.
SEMI-AUTO CLOCK SET
=HOST CHANNEL SELECT
TIME ZONE SELECT
D.S.T. SELECT
To select the Host Channel
— step 7
To select the Time Zone
— step 8
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
To select the D.S.T. mode — step 9
SELECT HOST CHANNEL
You can either select
“AUTO”, or enter a PBS channel number. For
HOST CHANNEL SELECT
automatic channel selection, simply press
(CATV)
CH AUTO
MENU. To manually select the PBS channel, press the appropriate NUMBER key,
PRESS (
5,∞) TO SELECT
PRESS (MENU) TO END
CH▲▼ or TIME SCAN
5∞ to cycle through the channel numbers (hold button down to speed through numbers) and stop when the desired number appears. Press MENU and the Semi-
Auto Clock Set screen reappears.
8
NOTES:
● For cable box users: Select "AUTO" or the channel on your VCR that receives the cable box channels, and set the cable box to the PBS channel.
● There are some PBS channels that do not transmit clock setting data.
SELECT TIME ZONE
You can either select
“AUTO”, or select the correct zone. If you selected "AUTO" in step 7 and if you live near the boundary of an adjacent
TIME ZONE SELECT
=AUTO
ATLANTIC
EASTERN
CENTRAL
MOUNTAIN
PACIFIC
ALASKA
HAWAII
time zone, or receive cable TV channels, a PBS
PRESS (
5,∞) TO SELECT
PRESS (MENU) TO END
channel from a different time zone may become your host channel. Therefore, in this case make sure to manually select the correct time zone. Place the arrow next to your choice by pressing CH
5∞ or TIME SCAN 5∞, then press MENU to return to the Semi-Auto Clock Set screen.
•
•
•
•
•
•
•
•
•
8
9
11
SELECT D.S.T. MODE
You have three choices:
a–Select “AUTO” and the adjustment to your VCR’s clock will be made according to the incoming signal from the host channel.
D.S.T. SELECT
=AUTO
ON
OFF
b–Select “ON” and the adjustment will be made
PRESS (
5,∞) TO SELECT
PRESS (MENU) TO END
based on the clock itself.
c–Select “OFF” if Daylight Saving Time doesn’t apply to you.
Place the arrow next to your choice by pressing CH
5∞ or TIME SCAN
5∞, then press MENU and the Semi-
Auto Clock Set screen reappears.
IMPORTANT
After setting the Semi-Auto clock set, make sure that the VCR is off before the next hour so that the clock can be adjusted.
(The clock is automatically adjusted on the hour except at
11:00 PM, midnight, 1:00 AM and 2:00 AM.)
NUMBER
MENU
1
4
7
2
5
8
0
3
6
9
CH
OK
TIME SCAN
**AUTO DAYLIGHT SAVING TIME
This function enables automatic adjustment of the VCR’s clock at the start and end of Daylight Saving Time.
With Auto DST activated, . . .
. . . on the first Sunday of April at 2:00 AM, the clock is adjusted to 3:00 AM.
. . . on the last Sunday of October at 2:00 AM, the clock is adjusted to 1:00 AM.
Auto
5
SELECT MODE
At the Override Auto Clock Set screen, place the arrow next to "AUTO CLOCK SET" by pressing CH▲▼ or
TIME SCAN
5∞, then power off the VCR. Do not power it on again until the clock has been adjusted.
The clock is automatically adjusted on the hour except at 11:00 PM, midnight, 1:00 AM and 2:00 AM. (The clock will be adjusted on the hour based on the time displayed on the VCR, not on the actual real time.)
Manual
5
SELECT MODE
At the Override Auto Clock Set screen (
Z
pg. 10), place the arrow next to “MANUAL CLOCK SET” by pressing
CH▲▼ or TIME SCAN
5∞, then press OK.
6
SET DATE, TIME AND D.S.T.
The Manual Clock Set screen is displayed and the first setting that can be set
MANUAL CLOCK SET
begins flashing.
Press the appropriate
DATE 1/ 1/96 MON
TIME – – : – – AM
D.S.T. ON
NUMBER keys to set the date and time (if only 1 digit, press "0" first). Press
PRESS NUMBER KEY(0-9)
OR (
5,∞), THEN (OK)
PRESS (MENU) TO END
CH▲▼ or TIME SCAN
5∞ to set AM/PM and D.S.T. (Daylight Saving Time) to
“ON” (automatic adjustment based on VCR’s clock) or
“OFF” (if D.S.T. doesn’t apply to you).
Press OK after AM/PM and D.S.T. settings. The next setting that can be set begins flashing. When you’re finished with this set-up procedure, press MENU to start the clock.
7
NOTE:
CH
5∞ and TIME SCAN 5∞ can be used to perform all operations. (In this case, press OK after each setting.)
MAKE CORRECTIONS
To change any of the settings, press OK or TIME SCAN
™
£ until the item you want to change blinks, then set as in step 6.
12
Tuner
•
•
•
•
•
•
•
•
•
•
MENU
1
4
7
2
5
8
0
3
6
9
CH
POWER
8
INITIAL SETTINGS (cont.)
Set Receivable Channels
TURN ON THE VCR
Press POWER.
1
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
2
3
ACCESS TUNER SET
SCREEN
Place the arrow next to "TUNER SET" by pressing
CH
5∞ or TIME SCAN 5∞, then press OK.
4
ACCESS BAND SCREEN
Place the arrow next to
"BAND" by pressing
CH
5∞ or TIME SCAN
5∞, then press OK.
TUNER SET
=BAND
AFC
AUTO CHANNEL SET
MANUAL CHANNEL SET
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
5
SET FREQUENCY BAND
If you receive your TV channels from an external antenna, select "TV". If
BAND
TV
=CATV you receive your TV channels from a cable TV system, select "CATV".
Place the arrow next to your choice by pressing
CH
5∞ or TIME SCAN
PRESS (
5,∞) TO SELECT
PRESS (MENU) TO END
5∞, then press MENU to return to the Tuner Set screen.
OK
TIME SCAN
•
•
•
•
•
•
•
1
4
7
2
5
8
0
3
6
9
CH
8
6
13
PERFORM AUTO CHANNEL
SET
Place the arrow next to
"AUTO CHANNEL SET" by pressing CH
5∞ or TIME
SCAN
5∞, then press OK.
Receivable channels in your area are automatically assigned to the CH
5∞ buttons, and non-receivable channels are skipped.
AUTO CHANNEL SET
(TV)
CH 2 ADD
SCANNING ...
PRESS (MENU) TO END
7
NOTES:
● At the end of Auto Channel Set, “SCAN COM-
PLETED” appears on screen.
● If the scan was unsuccessful, “SCAN COMPLETED–
NO SIGNAL” appears on screen. Check the band setting and connections and start again.
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
MENU
OK
TIME SCAN
14
•
•
•
•
•
•
•
•
•
•
NUMBER
CH.SKIP
1
4
7
2
5
8
0
3
6
9
CH
ADD
MENU
OK
TIME SCAN
8
INITIAL SETTINGS (cont.)
Add Or Delete A Channel
1
2
ACCESS TUNER SET
SCREEN
Access by performing steps 2 and 3 of the Tuner procedure on page 12.
● To add a channel, go to step 2.
● To delete a channel, skip to step 4.
ACCESS AFC SCREEN
Place the arrow next to "AFC" by pressing CH
5∞ or
TIME SCAN
5∞, then press OK.
3
MAKE SELECTION
Place the arrow next to
"SPCL" by pressing CH
5∞ or TIME SCAN
5∞, then press MENU to return to the Tuner Set screen.
AFC
NORM
=SPCL
4
● AFC set to SPCL (special) is necessary for turning on certain CATV systems.
PRESS (
5,∞) TO SELECT
PRESS (MENU) TO END
ACCESS MANUAL
CHANNEL SET SCREEN
Place the arrow next to "MANUAL CHANNEL SET" by pressing CH
5∞ or TIME SCAN 5∞, then press OK.
5
STORE DESIRED CHANNEL
Input the channel number using the NUMBER keys or by pressing CH
5∞ or TIME
SCAN
5∞, then press ADD to add or CH.SKIP to delete.
Repeat for each channel you want to store or skip.
MANUAL CHANNEL SET
(CATV)
CH 125 SKIP
SELECT CH NO. AND
PRESS (ADD/SKIP)
PRESS (MENU) TO END
6
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
Cable Box
Control
Suggested Location
Place the cable box on top of the VCR. Attach the VCR's
Controller to the top of the VCR with the Controller’s transmitter pointed towards the cable box’s remote sensor.
Attention:
The Controller can also control a DSS receiver. If both a cable box and a DSS receiver are used, position the controller so its signal reaches the remote control sensors of both the cable box and DSS receiver.
Cable box
Your VCR
Controller
Transmitter
Your VCR
Cable box
Connected to
ANT. IN
CABLE
BOX
Controller
(suggested locations)
15
This procedure is required if you receive your TV channels through a cable box (descrambler). The Controller allows the
VCR to automatically switch the cable box channel during timer-recording. The Controller is effective for recording shows that have been programmed using VCR Plus+ (
On-Screen Timer Programming (
Z
pg. 46).
Z
pg. 44) or
Situate And Connect
Controller
1
SITUATE CONTROLLER
Place the Controller so that the path between its transmitter and the cable box’s remote sensor is unobstructed.
ATTACH CONTROLLER
Fasten securely using the supplied adhesive strips.
2
3
CONNECT CABLE BOX TO
VCR
The connection method depends on the type of cable box you have.
If your cable box has AUDIO and VIDEO OUT connectors . . .
. . . connect them to the AUDIO and VIDEO IN connectors on your VCR.
If your cable box doesn’t have AUDIO and VIDEO
OUT connectors . . .
. . . connect the antenna output connector on the cable box to the ANT.IN connector on the rear of your VCR.
Set the VCR tuner to the same channel as the cable box
RF output (see page 17 also).
NOTE:
Refer to your cable box’s instruction manual during connection.
CONNECT CONTROLLER
TO VCR
Connect to the CABLE BOX connector on your VCR.
4
Connected to VIDEO/
AUDIO IN
About Your Cable Box
This VCR has two separate methods to control your Cable Box.
● The VCR's Wireless Remote Control Unit can control your
Cable Box.
This eliminates the need for a separate Cable Box Remote
Control Unit.
● The VCR's Controller can also control your Cable Box.
This allows the VCR to change your Cable Box's channel number during timer recording.
Each method must be set up separately. To set up the VCR's
Remote Control unit, refer to page 61. To set up the Controller go to page 16.
16
•
•
•
•
•
•
•
•
•
•
MENU
1
4
7
2
5
8
0
3
6
9
CH
POWER
OK
TIME SCAN
8
INITIAL SETTINGS (cont.)
Set Cable Box Output
Channel
TURN ON THE VCR
Press POWER.
1
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
2
3
ACCESS CUSTOM SET
SCREEN
Press CH
5∞ or TIME
SCAN
5∞ to place the arrow next to “CUSTOM
MAIN MENU
PROGRAM SET
FUNCTION SET
SET”, then press OK.
TUNER SET
=CUSTOM SET
VIDEO CALIBRATION
R.A. EDIT
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
4
ACCESS VCR PLUS+ SET-UP
SCREEN
Press CH
5∞ or TIME
SCAN
5∞ to place the arrow next to “VCR PLUS+
CUSTOM SET
OVERRIDE
AUTO CLOCK SET
SET-UP”, then press OK.
LANGUAGE SELECT
=VCR PLUS+ SET-UP
DSS RECEIVER OUTPUT
DSS RECEIVER BRAND SET
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
5
ACCESS CABLE BOX
OUTPUT SCREEN
Press CH
5∞ or TIME
SCAN
5∞ to place the arrow next to “CABLE
VCR PLUS+ SET-UP
GUIDE CHANNEL SET
BOX OUTPUT”, then press OK.
GUIDE CHANNEL MAP
=CABLE BOX OUTPUT
CABLE BOX BRAND SET
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
•
•
•
•
•
•
•
•
•
•
NUMBER
1
4
7
2
5
8
0
3
6
9
CH
ENTER
MENU
OK
TIME SCAN
8
17
6
SELECT CABLE BOX
OUTPUT CHANNEL
Your selection depends on how your cable box is connected to your VCR.
CABLE BOX OUTPUT
=OFF
ON CH2
ON CH3
ON CH4
If your cable box is
ON CH5 connected to your VCR using an RF connection . . .
. . . press CH
5∞ or TIME
ON CH6
ON LINE
PRESS (
5,∞), TO SELECT
PRESS (MENU) TO END
SCAN
5∞ to place the arrow next to the channel number representing the cable box’s output (2–6).
If your cable box is connected to your VCR’s AUDIO/
VIDEO IN connectors . . .
. . . press CH
5∞ or TIME SCAN 5∞ to place the arrow next to “ON LINE”.
RETURN TO VCR PLUS+
SET-UP SCREEN
Press MENU.
7
Set Cable Box Brand
1
TURN ON CABLE BOX
Select a channel other than channel 9 on your Cable
Box.
2
ACCESS CABLE BOX
BRAND SET SCREEN
At the VCR Plus+ Set-Up screen, press CH
5∞ or
TIME SCAN
5∞ to place the arrow next to “CABLE
BOX BRAND SET”, then press OK.
VCR PLUS+ SET-UP
GUIDE CHANNEL SET
GUIDE CHANNEL MAP
CABLE BOX OUTPUT
=CABLE BOX BRAND SET
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
3
ENTER CABLE BOX BRAND
Press the appropriate
NUMBER keys to enter the
Cable Box Code from the
CABLE BOX BRAND SET
1
CABLE BOX BRAND LIST on page 18, then press
ENTER.
● If the cable box’s channel changes to 9,
SELECT BRAND NO. AND
PRESS (ENTER)
PRESS (MENU) TO END
setting is complete.
● If there are more than one code number listed for your brand of cable box, repeat step 3 until the cable box’s channel changes to 9.
● If you go through all listed code numbers and the channel doesn’t change, try all other numbers between 1 and 69. That is because, maybe, your cable box model is not listed.
CONTINUED ON NEXT PAGE.
18
•
•
•
•
•
•
•
•
•
•
MENU
1
4
7
2
5
8
0
3
6
9
8
NOTES:
● Although the supplied Controller is compatible with many different cable box brands, it is possible that it will not work with your cable box.
● If your cable box doesn’t respond to any code between 1 and
69, you can’t use the Controller to change cable box channels. In this case, make sure to leave the cable box turned on and tuned to the proper channel before the scheduled start of timer recording.
Please contact your cable company about the possibility of exchanging your current cable box with one that is compatible with your VCR.
● The VCR can only change the cable box channel through the
Controller during timer recording.
● If your cable box is one that can’t be operated with a remote control (has no remote sensor), you can’t use the Controller to change its channels. Make sure to leave the cable box turned on and tuned to the proper channel before the scheduled start of timer recording.
● If you are unable to set the Controller, please contact JVC toll free at 1-800-252-5722.
INITIAL SETTINGS (cont.)
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
4
You can now set up the VCR Plus+ feature (
Z
pg. 19).
CABLE BOX BRAND LIST
BRAND
ARCHER
CABLEVIEW
CITIZEN
CURTIS
DIAMOND
EAGLE
EASTERN
GC BRAND
GEMINI
GENERAL ELECTRIC
GENERAL INSTRUMENTS
HAMLIN
JERROLD
MACOM, HITACHI
MAGNAVOX
MOVIETIME
NSC
OAK
PANASONIC
PHILIPS
PIONEER
PULSER
RCA
REGAL
REGENCY
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
SPRUCER
STARGATE
SYLVANIA
TEKNIKA
TELECAPTION
TELEVIEW
TEXSCAN
TOCOM
UNIKA
UNIVERSAL
VIDEOWAY
VIDEO TECH
VIDTER
VIEWSTAR
ZENITH
CODE
49, 52, 53, 54
49, 53
49, 53
9, 10, 62, 63
52, 53, 54
30, 31, 32, 33, 34, 35, 36, 37
51
49, 53
8, 56
67
1, 2, 3, 4, 5, 6, 7,8
15, 16, 17,18
1, 2, 3, 4, 5, 6, 7, 8
57, 58, 59
30, 31, 32, 33, 34, 35, 43
44, 45, 46
44, 45, 46
19, 20, 21, 30, 47, 48
24, 25, 26
30, 31, 32, 33, 42
13, 14
49, 53
24, 25, 26
15, 16, 17, 18, 33
51
8, 13, 49, 50
9, 10, 62, 63
19, 20, 21
8, 13, 49, 50
24, 25, 26
8, 13, 49, 50
29
68, 69
27
8, 13, 49, 50
28, 29
22, 23, 64, 65, 66
52, 53, 54
38, 39, 40, 41
11, 12, 60, 61
55
55
30, 31, 32, 33, 34, 35, 36, 37
11, 12, 60, 61
VCR Plus+
Setup
•
•
•
•
•
•
•
•
•
•
MENU
1
4
7
2
5
8
0
3
6
9
POWER
8
19
The VCR Plus+ timer programming system eliminates the need to input channel, date, start and stop time data when setting the timer record function. Simply key in the PlusCode number for the TV program you wish to record (found in most TV listings) and the VCR’s timer is automatically programmed.
Depending on the TV or cable stations that you receive and the channel numbers that they are received on in your area, you may have to make certain changes in your VCR’s “Guide Channel Set” menu to get proper results. Please read the following information carefully to find out which tasks you need to perform.
Before VCR Plus+ setup you must have performed the following procedures:
● Dual Quick setting (
Z
pg. 7)
or
Clock setting (
Z
pg. 9)
Tuner setting (
Z
pg. 12)
● Tuner and cable box setting if you receive your TV channels through a cable box (
Z
pg. 15)
Channel Number Matching
Most TV listings have a chart indicating the “Guide Channel” number assigned to each station for purposes of VCR Plus+ programming. Check the chart in your TV listings and see if the
Guide Channel numbers listed for the stations you receive are the same as the channel number on which each is received by your VCR or cable box.
**SPECIAL NOTES FOR CABLE SUBSCRIBERS**
● In many instances, cable TV stations have VCR Plus+ Guide
Channel numbers that DO NOT match the number of the channel on which you receive the station. Check your TV listings, or contact your cable supplier for details.
● Many normal broadcast TV stations can be viewed on cable.
Check your TV listing, or contact your cable supplier for details.
If the numbers match, go directly to “VCR Plus+ Timer
Programming” (
Z
pg. 44).
If the numbers are different, and you want to be able to timer record programs from those stations, you have to inform the
VCR of the mismatch. Go to step 1. If you will not want to timer record from those stations, you can go directly to “VCR Plus+
Timer Programming” (
Z
pg. 44).
1
TURN ON THE VCR
Press POWER.
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
2
CONTINUED ON NEXT PAGE.
20
•
•
•
•
•
•
•
•
•
•
NUMBER
1
4
7
2
5
8
0
3
6
9
CH
OK
TIME SCAN
8
INITIAL SETTINGS (cont.)
3
ACCESS CUSTOM SET
SCREEN
Press CH
5∞ or TIME
SCAN
5∞ to place the arrow next to “CUSTOM
MAIN MENU
PROGRAM SET
FUNCTION SET
SET”, then press OK.
TUNER SET
=CUSTOM SET
VIDEO CALIBRATION
R.A. EDIT
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
4
ACCESS VCR PLUS+ SET-UP
SCREEN
Press CH
5∞ or TIME
SCAN
5∞ to place the
CUSTOM SET
OVERRIDE
arrow next to “VCR PLUS+
AUTO CLOCK SET
SET-UP”, then press OK.
LANGUAGE SELECT
=VCR PLUS+ SET-UP
DSS RECEIVER OUTPUT
DSS RECEIVER BRAND SET
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
5
ACCESS GUIDE CHANNEL
SET SCREEN
Press CH
5∞ or TIME
SCAN
5∞ to place the arrow next to “GUIDE
VCR PLUS+ SET-UP
CHANNEL SET”, then
=GUIDE CHANNEL SET
GUIDE CHANNEL MAP
press OK.
CABLE BOX OUTPUT
CABLE BOX BRAND SET
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
6
INPUT GUIDE CHANNEL
NUMBER
Press CH
5∞, TIME SCAN
5∞ or the appropriate
GUIDE CHANNEL SET
GUIDE CH : VCR CH
NUMBER keys to input the
1 : 1
Guide Channel number as shown in the TV listing.
Then press OK.
● If you receive your channels with a cable
PRESS NUMBER KEY (0-9)
OR (
5,∞), THEN (OK)
PRESS (MENU) TO END
box and if you have properly set your Cable Box
Controller, “CABLE CH” appears in place of “VCR
CH”. If not, refer to pages 15–16 and re-perform the procedure.
•
•
•
•
•
•
•
•
•
•
NUMBER
1
4
7
2
5
8
0
3
6
9
CH
MENU
OK
TIME SCAN
8
21
7
INPUT RECEIVING CHANNEL
NUMBER
Press CH
5∞, TIME SCAN 5∞ or the appropriate
NUMBER keys to input the number of the channel on which the Guide Channel’s broadcasts are received.
Then press OK.
● If there is more than one mismatch, repeat steps 6 and 7 for each instance.
RETURN TO VCR PLUS+
SET-UP SCREEN
Press MENU.
8
9
10
CHECK INPUT DATA
Press CH
5∞ or TIME
SCAN
5∞ to place the arrow next to “GUIDE
VCR PLUS+ SET-UP
CHANNEL MAP”, then press OK.
GUIDE CHANNEL SET
=GUIDE CHANNEL MAP
CABLE BOX OUTPUT
CABLE BOX BRAND SET
● The Guide Channel and
VCR or cable box channel numbers you
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
input appear on the screen in ascending
GUIDE CHANNEL MAP
order. Check to ensure you’ve entered them
GUIDE : VCR
6 : 47
GUIDE : VCR
10 : 55
correctly.
● If you entered more than
10 sets of numbers, press
12 : 41
33 : 28
15 : 38
67 : 49
OK to see the next set of
PRESS (OK) TO NEXT
PRESS (MENU) TO END
numbers.
● Guide Channel Map contains only the Guide Channels and VCR channels that you entered.
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
You can now use VCR Plus+ for quick and simple timer programming (
Z
pg. 44).
22
DSS Receiver
Control
Suggested Location
Place the DSS (Digital Satellite System) receiver on top of the
VCR. Attach the VCR's Controller to the top of the VCR with the
Controller’s transmitter pointed towards the DSS receiver's remote sensor.
Attention:
The Controller can also control a cable box. If both a DSS receiver and a cable box are used, position the controller so its signal reaches the remote control sensors of both the DSS receiver and cable box.
Your VCR
DSS receiver
Controller
(suggested locations)
Controller
Transmitter
Connected to
ANT. IN
DSS receiver
Connected to VIDEO/
AUDIO IN
INITIAL SETTINGS (cont.)
The following procedure is required if you receive satellite channels through a DSS (Digital Satellite System) receiver and you want your VCR to change to receiver's channels during timer recording.
The VCR can control the DSS Receiver during timer recording using its Controller.
NOTE:
The Controller can automatically change the DSS Receiver channels when the VCR has been programmed using On-
Screen Timer Programming (
Z
pg. 46).
Because satellite programming does not use PlusCode; the
Controller can not change the DSS Receiver channels during
VCR Plus+ Timer Recording.
Situate And Connect
Controller
1
SITUATE CONTROLLER
Place the Controller so that the path between its transmitter and the DSS receiver's remote sensor is unobstructed.
ATTACH CONTROLLER
Fasten securely using the supplied adhesive strips.
2
3
CONNECT DSS RECEIVER
TO VCR
The connection method depends on the type of DSS receiver you have.
If your DSS receiver has AUDIO and VIDEO OUT connectors . . .
. . . connect them to the AUDIO and VIDEO IN connectors on your VCR.
If your DSS receiver doesn’t have AUDIO and VIDEO
OUT connectors . . .
. . . connect the antenna output connector on the DSS receiver to the ANT.IN connector on the rear of your VCR.
NOTE:
Refer to your DSS receiver's instruction manual during connection.
CONNECT CONTROLLER
TO VCR
Connect to the CABLE BOX connector on your VCR.
4
Your VCR
CABLE
BOX
•
•
•
•
•
•
•
•
•
•
MENU
1
4
7
2
5
8
0
3
6
9
CH
POWER
OK
TIME SCAN
8
Set DSS Receiver Output
Channel
TURN ON THE VCR
Press POWER.
1
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
2
3
ACCESS CUSTOM SET
SCREEN
Press CH
5∞ or TIME
SCAN
5∞ to place the arrow next to “CUSTOM
MAIN MENU
PROGRAM SET
FUNCTION SET
SET”, then press OK.
TUNER SET
=CUSTOM SET
VIDEO CALIBRATION
R.A.EDIT
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
23
4
ACCESS DSS RECEIVER
OUTPUT SCREEN
Press CH
5∞ or TIME
SCAN
5∞ to place the arrow next to “DSS
CUSTOM SET
OVERRIDE
AUTO CLOCK SET
RECEIVER OUTPUT”, then press OK.
LANGUAGE SELECT
VCR PLUS+ SET-UP
=DSS RECEIVER OUTPUT
DSS RECEIVER BRAND SET
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
5
6
SELECT DSS RECEIVER
OUTPUT CHANNEL
Your selection depends on how your DSS receiver is connected to your VCR.
DSS RECEIVER OUTPUT
If your DSS receiver is
=OFF
ON CH3
ON CH4
ON LINE connected to your VCR using an RF connection . . .
. . . press CH
5∞ or TIME
SCAN
5∞ to place the
PRESS (
5,∞), TO SELECT
PRESS (MENU) TO END
arrow next to the channel number representing the DSS receiver's output (3–4).
If your DSS receiver is connected to your VCR’s
AUDIO/VIDEO IN connectors . . .
. . . press CH
5∞ or TIME SCAN 5∞ to place the arrow next to “ON LINE”.
RETURN TO CUSTOM SET
SCREEN
Press MENU.
24
•
•
•
•
•
•
•
•
•
•
NUMBER
1
4
7
2
5
8
0
3
6
9
CH
ENTER
MENU
OK
TIME SCAN
8
NOTES:
● Depending on the type of DSS receiver, it is possible that the
Controller will not work with it.
● If your DSS receiver doesn’t respond to the code, you can’t use the Controller to change satellite channels. In this case, make sure to leave the DSS receiver turned on and tuned to the proper channel before the scheduled start of timer recording.
● The VCR can only change the satellite channel through the
Controller during timer recording.
● If your DSS receiver is one that can’t be operated with a remote control (has no remote sensor), you can’t use the
Controller to change its channels. Make sure to leave the DSS receiver turned on and tuned to the proper channel before the scheduled start of timer recording.
● If you are unable to set the Controller, please contact JVC toll free at 1-800-252-5722.
INITIAL SETTINGS (cont.)
Set DSS Receiver Brand
1
TURN ON DSS RECEIVER
Select a channel other than channel 205 on your DSS receiver.
2
ACCESS DSS RECEIVER
BRAND SET SCREEN
At the Custom Set screen, press CH
5∞ or TIME
SCAN
5∞ to place the arrow next to “DSS
RECEIVER BRAND SET”, then press OK.
CUSTOM SET
OVERRIDE
AUTO CLOCK SET
LANGUAGE SELECT
VCR PLUS+ SET-UP
DSS RECEIVER OUTPUT
=DSS RECEIVER BRAND SET
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
3
ENTER DSS RECEIVER
BRAND
Press the appropriate
NUMBER keys to enter the
DSS Receiver Code from the following list, then
DSS RECEIVER BRAND SET
80
press ENTER.
The unit is pre-set to code
80 (RCA) when shipped.
SELECT BRAND NO. AND
PRESS (ENTER)
PRESS (MENU) TO END
● If the DSS receiver's channel changes to 205, setting is complete.
BRAND
RCA
SONY
CODE
80
81
4
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
SIMPLE PLAYBACK AND RECORDING
25
Before performing the following steps, make sure the TV is set to the VCR channel (3 or 4) or AV mode.
Simple
Playback
•
•
•
•
•
•
•
•
•
STOP/EJECT
REW
8
FF
1
2
3
LOAD A CASSETTE
Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR. Don’t apply too much pressure when inserting.
● The VCR’s power comes on automatically.
● The counter is automatically reset to "0H 00M 00S".
● If the cassette's record safety tab has been removed, playback begins automatically.
FIND PROGRAM START
POINT
If the tape is advanced past the start point, press REW or turn the TIME SCAN SHUTTLE ring to the left. To go forward, press FF or turn the TIME SCAN SHUTTLE ring to the right.
START PLAYBACK
(
Press PLAY. "VIDEO CALIBRATION" appears on screen
Z
pg. 40).
4
STOP PLAYBACK
Press STOP or STOP/EJECT. Then press STOP/EJECT to remove the cassette.
1 2 3
4 5 6
7 8
0
9
PLAY
FF (Fast-Forward)
Usable cassettes
Full-Size VHS
T-30 (ST-30**)
T-60 (ST-60**)
T-90
T-120 (ST-120**)
T-160 (ST-160**)
ST-210**
REW (Rewind)
Compact VHS*
TC-20 (ST-C20**)
TC-30 (ST-C30**)
TC-40 (ST-C40**)
* Compact VHS camcorder recordings can be played on this video recorder. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette.
** This video recorder can record on regular VHS and
Super VHS cassettes. However, it will record and play back regular VHS signals only. It is not possible to play back Super VHS recordings.
26
Simple
Recording
•
•
•
•
•
•
•
•
•
•
NUMBER
PAUSE
1
4
7
2
5
8
0
STOP/EJECT
CH
3
6
9
SIMPLE PLAYBACK AND RECORDING (cont.)
CH
ENTER
8
1
2
3
4
LOAD A CASSETTE
Make sure the record safety tab is intact. If not, cover the hole with adhesive tape before inserting the cassette.
SELECT RECORDING
CHANNEL
Press CH
5∞. Or press the appropriate NUMBER keys, then press ENTER. (The channel changes after a few seconds whether you press ENTER or not.)
SET TAPE SPEED
Press SP/EP to set the recording speed.
START RECORDING
Press and hold REC and press PLAY on the remote control, or press REC on the VCR's front panel.
Active Video Calibration takes place at the beginning of both the first SP and the first EP recording after inserting the cassette (
Z
pg. 39).
5
6
PAUSE/RESUME
RECORDING
Press PAUSE. Press PLAY to resume recording.
● During record pause, you can change the recording channel by using the CH
5∞ buttons or NUMBER keys.
STOP RECORDING
Press STOP or STOP/EJECT. Then press STOP/EJECT to remove the cassette.
SP/EP
REC
PAUSE
Accidental erasure prevention
● To prevent accidental recording on a recorded cassette, remove its record safety tab.
To record on it later, cover the hole with adhesive tape.
Record safety tab
PLAYBACK AND RECORDING FEATURES
Playback
•
•
•
•
•
•
•
•
•
1 2
CH
3
8
2
27
Still Picture/Frame-By-
Frame Playback
1
PAUSE DURING PLAYBACK
Press PAUSE. If there is vertical jitter, use the CH
5 or ∞ button to correct the picture.
● During still picture, the sound from the previous
3 seconds (approx.) will be played back repeatedly
(provided there was at least 6 seconds of normal playback prior to engaging the still picture mode).
● "TIMESCAN AUDIO" must be set to "ON", or the sound will not be heard (
Z
pg. 37).
ACTIVATE FRAME-BY-
FRAME PLAYBACK
Turn the JOG dial to the right for forward frame-byframe playback, or to the left for reverse frame-by-frame playback.
OR
Press PAUSE repeatedly to advance one frame at a time.
OR
Press TIME SCAN ™ or £ repeatedly to advance one frame at a time.
Press TIME SCAN £ for forward frame by frame playback or TIME SCAN ™ for reverse frame by frame.
4 5 6
To resume normal playback, press PLAY.
7 8 9
0
CH
PLAY
PAUSE
TIME SCAN ™/£
Slow Motion/
Reverse Slow Motion
1
ACTIVATE SLOW-MOTION
PLAYBACK
For hands-free slow-motion, turn the TIME SCAN
SHUTTLE ring to the left or press TIME SCAN ™ during playback to decrease speed in the forward direction. To play in reverse slow-motion (and in reverse play mode), continue to turn the TIME SCAN
SHUTTLE ring to the left or press TIME SCAN ™ after selecting all the forward direction slow-motion modes.
OR
During still picture, turn the TIME SCAN SHUTTLE ring to the right for forward slow motion, or to the left for reverse slow motion.
OR
During still picture, press and hold TIME SCAN £ for forward slow motion, or press and hold TIME SCAN ™ for reverse slow motion. Release to return to still picture.
Refer to the chart on pg. 36 for slow motion speeds.
To resume normal playback, press PLAY.
28
•
•
•
•
•
•
•
•
•
•
1
4
7
2
5
8
0
3
6
9
PLAYBACK AND RECORDING FEATURES (cont.)
Manual Tracking
Once playback begins, the VCR’s automatic tracking function is engaged. If noise appears in the picture, you can override this and make the adjustment manually.
1
2
3
ENGAGE MANUAL
TRACKING MODE
During playback, press the CH
5∞ buttons on the
VCR's front panel simultaneously to cancel the automatic tracking mode and enable manual tracking adjust.
ADJUST MANUAL
TRACKING
Press CH
5∞ on the VCR's front panel or remote. Press lightly for fine adjust, or press and hold for coarse adjust. Watch the screen and continue adjusting until optimum picture and sound quality are achieved.
RE-ENGAGE AUTOMATIC
TRACKING
Press the CH
5∞ buttons on the VCR's front panel simultaneously.
● When automatic tracking is re-engaged, video calibration is automatically activated.
CH
8
NOTES:
● To obtain a noiseless still picture it may be necessary to adjust tracking in slow playback and then engage Pause.
● Manual tracking is possible during hands-free slow-motion.
During hands-free slow-motion playback, simply press CH
5 or
∞ on the VCR's front panel or remote to adjust tracking.
•
•
•
•
•
•
•
•
•
•
MENU
1
4
7
2
5
8
0
3
6
9
CH
OK
TIME SCAN
8
NOTES:
● If the tape being played back has no Hi-Fi soundtrack, the
Normal soundtrack will be heard no matter what choice you make at the Audio Select screen.
● If you select "HI-FI" or "MIX", the L and R symbols near the audio level meters will be illuminated.
29
Select The Soundtrack
Your VCR can record two soundtracks simultaneously (Normal and Hi-Fi) and play back the selected one, or both together.
1
2
ACCESS MAIN MENU
SCREEN
Press MENU during playback or when VCR is in stop mode.
● If the VCR Plus+ screen appears press MENU again.
ACCESS FUNCTION SET
SCREEN
Place the arrow next to "FUNCTION SET" by pressing
CH
5∞ or TIME SCAN 5∞, then press OK.
3
ACCESS AUDIO SELECT
SCREEN
Place the arrow next to
"AUDIO SELECT" by pressing CH
5∞ or TIME
SCAN
5∞, thenpress OK.
FUNCTION
AUTO TIMER
SUPERIMPOSE
2ND AUDIO
=AUDIO SELECT
AUX INPUT
SPECIAL FUNCTION
HI-FI REC LEVEL
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
4
ACCESS AUDIO MONITOR
SCREEN
Place the arrow next to
"AUDIO MONITOR" by pressing CH
5∞ or TIME
SCAN
5∞, then press OK.
AUDIO SELECT
=AUDIO MONITOR
TIMESCAN AUDIO
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
5
6
SELECT MODE
You have three choices:
a– Hi-Fi
b– Normal
c– Mix
AUDIO MONITOR
=HI-FI
NORM
MIX
Place the arrow next to your choice by pressing CH
5∞ or TIME SCAN
5∞.
PRESS (
5,∞) TO SELECT
PRESS (MENU) TO END
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
30
•
•
•
•
•
•
•
•
•
•
MENU
1
4
7
2
5
8
0
3
6
9
PLAYBACK AND RECORDING FEATURES (cont.)
CH
OSD
8
Superimpose
This function, switchable between ON and OFF, determines whether or not operational indicators will appear on screen.
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
1
2
ACCESS FUNCTION SET
SCREEN
Place the arrow next to "FUNCTION SET" by pressing CH
5∞ or TIME SCAN 5∞, then press OK.
3
ACCESS SUPERIMPOSE
SCREEN
Place the arrow next to
"SUPERIMPOSE" by pressing CH
5∞ or TIME
SCAN
5∞, then press OK.
FUNCTION
AUTO TIMER
=SUPERIMPOSE
2ND AUDIO
AUDIO SELECT
AUX INPUT
SPECIAL FUNCTION
HI-FI REC LEVEL
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
4
SELECT MODE
Place the arrow next to
"ON" or "OFF" by pressing
CH
5∞ or TIME SCAN 5∞.
OK
SUPERIMPOSE
=ON
OFF
TIME SCAN
To recall an indication
1
Press OSD.
n All indications corresponding to the current status are displayed for 5 seconds, leaving the counter information, and RECORD/PAUSE if in the Record Pause mode, on the screen. (No indication during still and search.)
2
Press OSD again to clear the display.
PRESS (
5,∞) TO SELECT
PRESS (MENU) TO END
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
5
NOTE:
If you engage the Record Pause mode, RECORD/PAUSE is displayed whether "SUPERIMPOSE" is set to "ON" or "OFF".
The superimposed indication on the TV screen tells you what the VCR is doing.
Tuned-in channel or AUX(iliary) mode
When the channel is changed, the new channel is displayed on the screen for 5 seconds.
CH 125
THU 12:00 AM
RECORD
PAUSE
]
SP
Clock time
B
+ + +
E
Tape position indicator
NORM
HI–FI COUNT
INDEX-1
MEMORY OFF
–1:23:45
"Cassette Loaded" mark
When a cassette is loaded, the mark is displayed for 5 seconds. It blinks when the
VCR's EJECT button is pushed.
Audio mode indicators
Operation mode
When the operation mode is changed, the new mode is displayed — RECORD
(5 sec.), PLAY (5 sec.), FF/REW (5 sec.
when engaged from Stop mode),
RECORD PAUSE (for as long as Pause is engaged), and ITR *:** (5 sec.).
Tape speed indicator
INDEX indication
Counter reading
Counter memory on/off
•
•
•
•
•
•
•
•
•
•
INDEX ERASE
STOP
REW
1
4
7
2
5
8
0
3
6
9
PLAY
FF
PAUSE
STOP
TIME SCAN
8
31
Index Search
This function seeks out index codes that are placed on the tape at recording start.
1
START SEARCH
While the tape is stopped, press TIME SCAN ™ or
£
.
2
ACCESS DISTANT CODE
To access a recording 2–9 index codes away, press
TIME SCAN ™ or £ repeatedly until the correct number is displayed on screen (only if SUPERIMPOSE is set to ON (
Z
pg. 30). Playback begins automatically when the desired recording is located.
● To find the very beginning of the desired program, press REW or FF and search visually for the start point.
NOTE:
An index code is not placed on the tape when recording is paused and then resumed.
Manual Index Mark/Erase
To mark an index code...
...during playback press INDEX MARK on the VCR.
n The VCR will mark an index code at that location.
n If "SUPERIMPOSE" is set to ON (
Z
pg. 30), "MARK" blinks on the screen while an index code is being marked.
To erase an index code...
...during playback or still press INDEX ERASE on the VCR.
n The VCR will fast-forward to the nearest index code (Sound will not be heard during this) and erase it. Playback continues after the index code is erased.
n If "SUPERIMPOSE" is set to ON (
Z
pg. 30), "ERASE" blinks on the screen while an index code is being erased.
Repeat Playback
1
START REPEAT
Press and hold PLAY (until "PLAY" blinks on the front display panel) during playback, then release.
VIDEO SP PLAY
H M S
2
● The entire tape is played back 20 times.
STOP REPEAT
To stop, press STOP at any time.
NOTE:
Pressing PLAY, REW, FF, PAUSE or TIME SCAN ™ or
£
also stops Repeat Playback.
32
•
•
•
•
•
•
•
•
•
•
REVIEW
C.RESET
REW
C.MEMORY
1
4
7
2
5
8
0
DISPLAY
3
6
9
PLAYBACK AND RECORDING FEATURES (cont.)
STOP
REW
8
FF
Instant ReView
At the press of a button, you can power up your VCR, rewind the tape and begin viewing the most recent timer-recorded program.
1
ACTIVATE INSTANT REVIEW
After ensuring that the VCR is off and the Timer mode is disengaged, press REVIEW.
● The power comes on and the VCR searches for the index code indicating the start of the last timer-recorded program, then begins playback automatically.
● You can access a program 2–9 index codes away from the current position on the tape. If, for example, you have 5 programs recorded and you want to watch the third one, press REVIEW three times.
● To find the very beginning of the desired program, press REW or FF and search visually for the program’s start point.
Counter Reset
1
RESET COUNTER TO ZERO
Press C.RESET.
NOTE:
By pressing the DISPLAY button, you can change the display to show the counter reading, channel number or clock time. (Channel number is not displayed during playback.)
FF
STOP
Counter Memory
When activated, this feature returns the tape to counter position
“zero”.
1
2
ACTIVATE COUNTER
MEMORY
Press C.RESET during playback at a point you want to have quick access to later. The counter reads “0H 00M 00S”.
Then press C.MEMORY. The Counter Memory indicator in the front display panel lights.
RETURN TO COUNTER
POSITION ZERO
Press STOP (during playback), then press REW or FF.
The tape rewinds or fast-forwards and stops at approximately “0H 00M 00S” automatically.
● To cancel Counter Memory, press C.MEMORY.
•
•
•
•
•
•
•
•
•
REW
POWER
REW
PLAY
1
4
7
2
5
8
0
3
6
9
TIMER
FF
C.MEMORY
MENU
8
FF
33
Tape Position Indicator
The Tape position indicator appears on screen when, from the stop mode, you press FF, REW, or use the TIME SCAN SHUTTLE ring, or perform an Index Search or
Instant ReView. The position of "
" in relation to "B" (Beginning) or
"E" (End) shows you where you are on the tape.
B
+ +
COUNT
+
E
0:33:27
NOTE:
"SUPERIMPOSE" must be set to "ON", or the indicator will not appear (
Z
pg. 30).
Next-Function Memory
The Next Function Memory “tells” the VCR what to do after rewinding. * Before continuing, ensure that the VCR is in stop mode.
a– For Automatic Start Of Playback After Tape Rewind . . .
. . . press REW, then press PLAY within 2 seconds.
b– For Automatic Power Off After Tape Rewind . . .
. . . press REW, then press POWER within 2 seconds.
c– For Automatic Timer Standby After Tape Rewind . . .
. . . press REW, then press TIMER within 2 seconds.
NOTE:
If you want the "next function" to automatically start when the counter reads "0H 00M 00S" (instead of at the beginning of the tape), press C. MEMORY so that the counter memory indicator appears on the front display panel before pressing REW or FF.
AV COMPU LINK Playback
Your VCR is compatible with JVC’s AV COMPU LINK components, including amplifiers (or receivers) and televisions. AV COMPU
LINK provides one touch control of the audio and video components that are linked via their AV COMPU LINK connectors.
For example: simply load a cassette in the VCR and press PLAY and the AV COMPU LINK components automatically power on, the TV's VIDEO mode is selected and the VCR goes into play mode. (PLAY need not be pressed if the cassette's record safety tab is removed.)
1
MAKE CONNECTION
Connect your VCR to an AV COMPU LINK component as shown in the illustration on page 34.
● The mini-plug cable is a mono 3.5 mm mini-plug to mono 3.5 mm mini-plug connector.
TURN ON THE VCR
Press POWER.
2
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
3
CONTINUED ON NEXT PAGE.
34
•
•
•
•
•
•
•
•
•
•
Example
MENU
VIDEO OUT
1
4
7
2
5
8
0
3
6
9
PLAYBACK AND RECORDING FEATURES (cont.)
CH
8
4
5
ACCESS FUNCTION SET
SCREEN
Press CH
5∞ or TIME SCAN 5∞ to place the arrow next to “FUNCTION SET”, then press OK.
ACCESS SPECIAL
FUNCTION SCREEN
Press CH
5∞ or TIME
SCAN
5∞ to place the arrow next to “SPECIAL
FUNCTION
AUTO TIMER
SUPERIMPOSE
2ND AUDIO
FUNCTION”, then press
OK.
AUDIO SELECT
AUX INPUT
=SPECIAL FUNCTION
HI-FI REC LEVEL
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
6
ENABLE AV COMPU LINK
PLAYBACK
Press CH
5∞ or TIME SCAN
5∞ to place the arrow next to “AV COMPU LINK”.
SPECIAL FUNCTION
R.A. EDIT/PAUSE
=AV COMPU-LINK
PLAY
OK
TIME SCAN
Your VCR
PRESS (
5,∞) TO SELECT
PRESS (MENU) TO END
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
7
8
PERFORM AV COMPU LINK
PLAYBACK
Simply insert a cassette and press PLAY (if the cassette’s record safety tab has been removed, playback begins automatically). Linked components are turned on, and the TV set to its VIDEO mode, automatically!
PAUSE/SPECIAL
FUNCTION
NOTE:
Connection varies depending on the type of JVC TV you have.
Please refer to the TV’s instruction manual when making this connection.
AUDIO OUT
Mini-plug cable
(not supplied)
VIDEO IN
AUDIO IN
AV COMPU LINK
Television
AV COMPU LINK II
(VCR ONLY)
TimeScan
TIME SCAN SHUTTLE INDICATOR
TIME SCAN INDICATOR
• • •
•
•
•
•
REW
8
35
Your VCR is equipped with the TimeScan function. TimeScan allows noise free pictures to be displayed on your TV screen in the forward and reverse search modes. Audio will be played back at normal speed during any of the TimeScan modes (
Z
pg. 36).
TimeScan allows you to view a program in search mode while listening to the audio.
NOTES:
● "TIMESCAN AUDIO" must be set to "ON", or the sound will not be heard in TimeScan mode (
Z
pg. 27)
Z
pg. 37).
● The audio will not synchronize with the video in TimeScan modes.
● In Pause mode 3 seconds (approx.) of audio will be played back repeatedly. (
● In TimeScan search modes some of the audio information will not be played so that the audio can keep up with the video.
● If "VIDEO CALIBRATION" is displayed, wait for this function to complete before selecting a play or search mode.
Audio signal during TimeScan
Playback tape 1 2 3 4 5
Sound of 1, 3 and 5 is heard.
Sound of 2 and 4 is not heard.
Output audio signal is normal (monaural) sound.
REW
1
4
7
2
5
8
0
3
6
9
PLAY
FF
TIME SCAN
High-Speed Search
(7x playback)
1
ACTIVATE HIGH-SPEED
SEARCH
During playback or still, press FF for forward high-speed search, or REW for reverse high-speed search.
To resume normal playback, press PLAY.
NOTE:
For short searches, during playback or still, press and hold FF or
REW for over 2 seconds. When released, normal playback resumes.
Variable-Speed Search/
Reverse Play
1
ACTIVATE VARIABLE-SPEED
SEARCH
During playback or still, turn the VCR's TIME SCAN
SHUTTLE ring. It remains at that position even after you release it. Each time it passes a click position, the playback speed changes.
(Refer to the chart on pg 36 for playback speeds).
OR
During playback, press TIME SCAN ™ or £.
● To increase the speed in the forward direction, press
£
.
● To decrease the speed in the forward direction, press
™
.
● To play in reverse slow motion, and in reverse play mode, continue to press ™ after selecting all the forward slow motion modes.
(Refer to the chart on pg 36 for playback speeds).
To resume normal playback, press PLAY.
36
TimeScan
PLAYBACK AND RECORDING FEATURES (cont.)
Names of special-effects playback
Speed
VCR's Time
Scan shuttle indicator
Search
Reverse
Play Slow-Motion *Still
X-7 X-5 X-3 X-1 X-1/6 X -1/18
SEARCH SLOW
Orange Green
0
6
Red
Slow-Motion
X1/18 X1/6
SLOW
Green
Forward
Play
X1
Search
X2 X3 X5 X7
SEARCH
Orange
Audio output
Audio is output.
Audio is not output.
Audio is output.
* Still mode cannot be engaged using the remote control's TIME SCAN button.
● The VCR's TimeScan indicator lights during TimeScan.
● The speed is shown in the upper right corner of the TV screen for approx. 5 seconds.
● The TimeScan search speed is the same for SP and EP recordings.
● To resume normal playback, press PLAY.
● When using the VCR's TIME SCAN SHUTTLE ring, the playback speed may not change depending on how far it is turned.
● When using the VCR's TIME SCAN SHUTTLE ring, the playback speed will change up to X7 and -X7 search speeds. Turning the TIME SCAN SHUTTLE ring further will not increase the search speed.
● Picture may be distorted at the position where the recording speed is switched.
● The picture may be noisy for a moment when you change the playback speed.
● Depending on the tape in use, noise may appear or the upper part of the picture may be distorted.
● Picture may appear distorted in comparison to normal playback.
● In TimeScan mode there will be a time lag between the video and the audio and noise may appear in the audio signal.
● TimeScan sound quality will differ in comparison to normal playback.
● When the playback direction is reversed, it takes approximately 6 seconds until sound is heard.
1
4
7
2
5
8
0
3
9
Skip Search
1
SKIP OVER UNWANTED
SECTIONS
Press SKIP SEARCH 1 to 4 times during playback. Each press initiates a 30-second period of fast- motion playback. Normal playback resumes automatically.
NOTE:
To return to normal playback during a Skip Search, press PLAY.
SKIP SEARCH
•
•
•
•
•
•
•
MENU
1
4
7
2
5
8
0
3
6
9
CH
OK
TIME SCAN
8
37
TimeScan Audio
The audio output can be set ON/OFF during TimeScan. Select
ON/OFF as required.
*The default setting is "ON".
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
1
2
ACCESS FUNCTION SET
SCREEN
Place the arrow next to "FUNCTION SET" by pressing
CH
5∞ or TIME SCAN 5∞, then press OK.
3
ACCESS AUDIO SELECT
SCREEN
Place the arrow next to
"AUDIO SELECT" by pressing CH
5∞ or TIME
SCAN
5∞, thenpress OK.
FUNCTION
AUTO TIMER
SUPERIMPOSE
2ND AUDIO
=AUDIO SELECT
AUX INPUT
SPECIAL FUNCTION
HI-FI REC LEVEL
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
4
ACCESS TIMESCAN
AUDIO SCREEN
Place the arrow next to
"TIMESCAN AUDIO" by pressing CH
5∞ or TIME
SCAN
5∞, thenpress OK.
AUDIO SELECT
AUDIO MONITOR
=TIMESCAN AUDIO
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
5
SELECT MODE
Place the arrow next to
"ON" or "OFF" by pressing
CH
5∞ or TIME SCAN
5∞.
TIMESCAN AUDIO
=ON
OFF
PRESS (
5,∞), TO SELECT
PRESS (MENU) TO END
6
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
38
PLAYBACK AND RECORDING FEATURES (cont.)
Active Video
Calibration
Your VCR is equipped with the Active Video Calibration feature, which checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures. *The default setting for both recording and playback is "ON".
•
•
•
•
•
•
•
•
•
•
MENU
1
4
7
2
5
8
0
3
6
9
CH
OK
POWER
8
Preparation
TURN ON THE VCR
Press POWER.
1
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
2
3
ACCESS VIDEO
CALIBRATION SCREEN
Press CH
5∞ or TIME
SCAN
5∞ to place the arrow next to “VIDEO
MAIN MENU
PROGRAM SET
FUNCTION SET
CALIBRATION”, then press OK.
TUNER SET
CUSTOM SET
=VIDEO CALIBRATION
R.A. EDIT
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
4
SELECT MODE
Place the arrow next to
"ON" by pressing CH
5∞ or TIME SCAN
5∞, then press OK to move the arrow to the Playback section. Set Playback to
ACTIVE VIDEO CALIBRATION
RECORDING
= ON
OFF
PLAYBACK
= ON
OFF
"ON", then press MENU as many times as necessary to
PRESS (
5,∞), THEN (OK)
PRESS (MENU) TO END
return to the normal screen.
(Pressing OK returns the arrow to the Recording section.)
NOTE:
When recording or when playing back tapes recorded on this VCR set the Active Video Calibration to "ON".
TIME SCAN
•
•
•
•
•
•
•
•
•
•
REC
PAUSE
1
4
7
2
5
8
0
PLAY
3
6
9
PAUSE
8
Recording
Perform steps 1 – 3 on page 26 ("Simple Recording") before continuing.
39
1
START RECORDING
Press and hold REC and press PLAY on the remote control, or press REC on the VCR's front panel.
DURING CALIBRATION
● The VCR takes about 7 seconds to assess the quality of the tape in use, then recording begins with the picture level optimized.
START END
+
ACTIVE VIDEO CALIBRATION
+
NOTES:
● Calibration occurs immediately prior to both the first SP and the
CALIBRATION COMPLETE first EP recording after inserting the cassette. It
START END
does not take place
+
during recording.
● In the case of timer
ACTIVE VIDEO CALIBRATION
recording, calibration takes place for both SP and EP
+
before the first timer recording after inserting the cassette
(regardless of the tape speed selected for that recording).
● Once the cassette is ejected, the calibration data is canceled. The next time the cassette is used for recording, calibration is re-performed.
● While Active Video Calibration is operative, the
PAUSE button will not function.
● SUPERIMPOSE must be set to "ON" or the Active
Video Calibration screen will not appear (
Z
pg. 30).
ATTENTION:
n As calibration takes place before recording actually starts, there is a delay of about 7 seconds after REC and PLAY on the remote, or REC on the VCR's front panel, are pressed.
To make sure you record the desired scene or program completely, first perform the following steps:
1) Press and hold PAUSE, and press REC to engage the
RECORD PAUSE mode.
● The VCR then automatically checks the condition of the tape and, after about 7 seconds, re-enters RECORD
PAUSE.
2) Press PLAY to start recording.
n If you want to bypass Active Video Calibration and start recording right away, set "RECORDING" to "OFF" in step
4 of the Preparation procedure (
Z
pg. 38).
40
•
•
•
•
•
•
•
•
•
•
PLAY
1
4
7
2
5
8
0
3
6
9
PLAYBACK AND RECORDING FEATURES (cont.)
Playback
The VCR assesses the quality of the tape once you initiate playback.
Before beginning, perform steps 1 and 2 on page 25.
8
1
START PLAYBACK
Press PLAY.
● The VCR adjusts the playback picture quality based on the quality of the tape in use.
VIDEO CALIBRATION
NOTES:
● When using rental tapes, or tapes recorded on other
VCRs, set “PLAYBACK” in step 4 of the Preparation
( procedure to either “ON” or “OFF” as desired
Z
pg. 38).
● The Video Calibration screen only appears at the beginning of automatic tracking. Even though the screen doesn't appear after that, the Active Video calibration function is operative.
● “SUPERIMPOSE” must be set to "ON" or the Video
Calibration screen will not appear (
Z
pg. 30).
Recording
•
•
•
•
•
•
•
•
•
•
C.RESET
1
4
7
2
5
8
0
3
6
9
TV/VIDEO
OSD
8
41
Record One Program While
Watching Another
1
2
ENGAGE TV MODE
During recording...
● Press TV/VIDEO. The VCR's VIDEO indicator goes out. (If you are using the RF connection (
Z
pg. 6). to view the output from your VCR, the TV broadcast being recorded disappears.)
● If you are using the AV connection (
Z
pg. 6), to view the output from your VCR, change the TV's input mode from AV to TV.
SELECT CHANNEL FOR
VIEWING
Use the TV’s channel selector to set the channel you want to watch.
Display Elapsed Recording
Time
1
2
RESET COUNTER TO ZERO
Before recording starts, press C.RESET. The counter resets to zero and displays the exact elapsed time as the tape runs.
DISPLAY ELAPSED TIME ON
SCREEN
During recording, press OSD at any time to see the elapsed time. All indications corresponding to the current status of the VCR are displayed for 5 seconds.
The counter display remains on the screen indicating the elapsed time. Press OSD again to remove the display.
● Make sure "SUPERIMPOSE" is set to "ON" (
Z
pg. 30).
42
•
•
•
•
•
•
•
•
•
•
MENU
1
4
7
2
5
8
0
3
6
9
PLAYBACK AND RECORDING FEATURES (cont.)
8
Stereo And SAP
(Second Audio Program)
Your VCR’s built-in MTS decoder enables reception of Multichannel TV Sound broadcasts.
● The ST indicator on the front display panel lights during stereo broadcast reception, and SAP lights during SAP program reception.
● Both indicators light when a stereo program is accompanied by SAP audio.
To Record Stereo Programs . . .
. . . simply follow the basic recording procedure.
To Listen To Stereo Soundtrack During Recording . . .
. . . select "HI-FI" at the Audio Monitor screen (
Z
pg. 29).
CH
OK
TIME SCAN
To Record SAP Programs . . .
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
1
2
ACCESS FUNCTION SET
SCREEN
Place the arrow next to "FUNCTION SET" by pressing
CH
5∞ or TIME SCAN 5∞, then press OK.
3
ACCESS 2ND AUDIO
SCREEN
Place the arrow next to "2ND AUDIO" by pressing
CH
5∞ or TIME SCAN 5∞, then press OK.
4
SELECT MODE
Place the arrow next to
"ON" by pressing CH
5∞ or TIME SCAN
5∞.
2ND AUDIO
=ON
OFF
PRESS (
5,∞) TO SELECT
PRESS (MENU) TO END
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
5
NOTES:
● If a SAP program is received, the SAP audio is recorded on both the Normal and Hi-Fi tracks. The main audio program is not recorded.
● If a non-SAP program is received, the main audio is recorded on both the Hi-Fi and Normal audio tracks.
•
•
•
•
•
•
•
•
•
•
REW
MENU
OK
1
4
7
2
5
8
0
3
6
9
CH
OK
TIME SCAN
POWER
FF
8
NOTE:
● Noise will increase if the recording level is too low, while distortion will increase if the level is too high.
FF
43
Hi-Fi Audio Recording Level
Control
Your VCR allows manual adjustment of the Hi-Fi audio recording level. Although the preset audio recording level is satisfactory for normal recording, if the sound you are going to record is too loud or too low, adjust the audio recording level while referring to the VCR's audio level meters.
TURN ON THE VCR
Press POWER.
1
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
2
3
ACCESS FUNCTION SET
SCREEN
Press CH
5∞ or TIME SCAN 5∞ to place the arrow next to “FUNCTION SET”, then press OK.
4
ACCESS HI-FI REC LEVEL
SCREEN
Press CH
5∞ or TIME SCAN 5∞ to place the arrow next to “HI-FI REC LEVEL”, then press OK.
5
SELECT MODE
Place the arrow next to
“MANUAL” by pressing
CH
5∞ or TIME SCAN
5∞.
HI-FI REC LEVEL CONTROL
PRESS
(REW)
PRESET
=MANUAL
PRESS
(FF)
MIN------*------MAX
PRESS (
5, ∞) TO SELECT
PRESS (MENU) TO END
6
7
ADJUST AUDIO RECORD-
ING LEVEL
Press FF or REW.
● To move the on-screen's audio levels by one division of the scale, press FF or REW briefly for 5 times in succession. To move the audio levels faster, keep FF or REW presssed.
● Adjust the recording level so that the audio level meters reach from 0dB to 4dB at the maximum sound volume.
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary to exit.
44
VCR Plus+
Timer
Programming
Before VCR Plus+ Timer programming, see "VCR Plus+
Setup" on page 19.
•
•
•
•
•
• •
•
•
•
•
NUMBER
CANCEL
MENU
OK
1
4
7
2
5
8
0
3
6
9
TV/CABLE/VCR
OK
8
ILLUMI GUIDE
When Using The Illumi-Guide Feature
● Buttons light or blink on the remote control for approximately 10 seconds. If the button or buttons extinguish during timer programming, press ILLUMI GUIDE and the button or buttons previously lit or blinking come back on. If the button or buttons do not re-light or start blinking again, press MENU as many times as necessary to return to the normal screen and extinguish all illuminated buttons, and re-perform the timer programming procedure from the beginning.
● If for some reason the remote control's signal is not received by the VCR, press MENU as many times as necessary to return to the normal screen and extinguish all illuminated buttons, and re-perform the timer programming procedure from the beginning.
Timer recording allows you to program the VCR to automatically record a program which will be broadcast at some future time.
The timer record function can be programmed using VCR Plus+ or On-Screen Timer Programming. (
Z
pg. 46)
During VCR Plus+ and on-screen programming, the Illumi-
Guide feature tells you which button on the remote control must be pressed next by lighting the relevant buttons. The
Illumi-Guide feature is activated by the ILLUMI GUIDE button on the remote control. The Illumi-Guide feature is only active when the remote control's TV/CABLE/VCR switch is set to
"VCR". (Illumi-Guide is an optional help feature which makes programming easier. It is not necessary to use Illumi-Guide to program the VCR.)
1
LOAD A CASSETTE
Make sure the record safety tab is present.
● The VCR’s power comes on automatically.
2
3
ACCESS VCR PLUS+ SCREEN
To use the Illumi-Guide feature press ILLUMI
GUIDE. MENU, REW,
PLAY and FF will light.
Press MENU on the remote control.
VCR PLUS+
● The clock must be set in order to access the VCR
PRESS NUMBER KEY(0-9)
PRESS (MENU) TO MAIN MENU
Plus+ screen. If you haven’t set the clock, the Main
Menu screen appears when you press MENU. Refer to page 7 for the Dual Quick Set procedure or page 9 for the clock setting procedure.
● If you are using the Illumi-Guide feature, the following buttons will light up: NUMBER keys (0 – 9), CANCEL and MENU.
ENTER PLUSCODE NUMBER
Press the appropriate NUMBER keys to enter the
PlusCode number printed in the TV listings for the TV program you wish to record.
● To make corrections, press CANCEL and input the correct PlusCode number.
● If the PlusCode number you input is incorrect,
"ERROR" may appear on the screen to advise you of the error. This happens when the PlusCode number is for a program which has already passed. "ERROR" is displayed for about 4 seconds and the VCR Plus+ screen reappears (step 2).
● If you are using the Illumi-Guide feature, OK blinks when the following buttons are lit: NUMBER keys
(0 – 9), CANCEL and MENU.
•
•
•
•
•
•
•
•
•
•
SP/EP
MENU
OK
TIME SCAN
8
NUMBER
1
4
7
2
5
8
0
3
6
9
CH
NUMBER "9"
TIMER
NUMBER "8"
45
4
CHECK INPUT DATA
Press OK and the Program screen appears.
The PlusCode number you entered appears in the
Program screen. Check to make sure it’s accurate.
PROGRAM 1
(VCR PLUS+ 12345678)
DATE
START
7/10 FRI
8:00 PM
STOP
CHANNEL
9:00 PM
8 SP
● To timer-record daily or weekly serials, press
PRESS (8=DAILY, 9=WEEKLY
SP/EP=REC SPEED)
PRESS (MENU) TO END
DAILY (NUMBER “8”) or
WEEKLY (NUMBER “9”). “DAILY” or “WEEKLY” appears on the Program screen.
● For weekly recording, the desired date for the day of the week must be entered.
● If you made a mistake, press CANCEL and, after pressing MENU as many times as necessary to access the VCR Plus+ screen, input the correct PlusCode number.
● If you are using the Illumi-Guide feature, MENU lights up for about 10 seconds.
SET TAPE SPEED
Press SP/EP.
5
6
7
CHECK/CORRECT INPUT
DATA
If the data is correct as it is, go to step 7. If not, press
OK or TIME SCAN ™£ until the item you want to change begins to blink. Then press the appropriate
NUMBER keys, CH
5∞ or TIME SCAN 5∞ to obtain the desired setting.
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
● Press just once to access the Auto Timer screen
(
Z
pg. 49).
ENGAGE TIMER MODE
Press TIMER. The VCR turns off automatically.
8
NOTES:
● To disengage the timer before recording starts, press TIMER again. Pressing once more re-engages it.
● In case of a power failure after programming, the VCR’s memory backup keeps your selections for approximately
10 minutes.
● When timer-recording cable channels received through a
Cable Box, be sure to keep the Cable Box set to ON.
46
On-Screen
Timer
Programming
•
•
•
•
•
•
•
•
•
•
NUMBER
MENU
1
4
7
2
5
8
0
3
6
9
CH
OK
TIME SCAN
ILLUMI GUIDE
8
TIMER RECORDING (cont.)
You can directly program the VCR’s timer to record up to 8 shows, as far as a year in advance. Remember, the clock must be set before you can program the timer (
Z
pg. 7 or 9).
You can also use the optional Illumi-Guide feature, where the relevant buttons on the remote control light to tell you which button to press next. The Illumi-Guide feature is activated by the
ILLUMI GUIDE button on the remote control. The Illumi-Guide feature is only active when the remote control's TV/CABLE/VCR switch is set to "VCR". (Illumi-Guide is an optional help feature which makes programming easier. It is not necessary to use
Illumi-Guide to program the VCR.)
1
2
3
4
LOAD A CASSETTE
Make sure the record safety tab is intact. If not, cover the hole with adhesive tape, then load.
● The VCR comes on, and the counter is reset, automatically.
ACCESS ON-SCREEN
MENU
To use the Illumi-Guide feature press ILLUMI GUIDE.
MENU, REW, PLAY and FF will light.
Press MENU as many times as necessary to bring up the
Main Menu screen.
● If you are using the Illumi-Guide feature, MENU lights up and OK blinks.
ACCESS PROGRAM SET
SCREEN
Make sure the arrow is to the left of "PROGRAM
SET", then press OK.
● If you are using the
Illumi-Guide feature, OK blinks when the following buttons are lit:
NUMBER keys (0 – 9),
PROGRAM 1
DATE - - / - -
START - - : - - AM
STOP - - : - - AM
CHANNEL - - SP
PRESS NUMBER KEY(0-9)
OR (
5,∞), THEN (OK)
PRESS (MENU) TO END
TIME SCAN, CANCEL and MENU.
SELECT PROGRAM NUMBER
Press the appropriate NUMBER keys or CH
5∞ or TIME
SCAN
5∞ to select a vacant program number, then press
OK. The first time you do this, all numbers will be vacant, so just press OK when the screen appears.
● If you are using the Illumi-Guide feature, OK blinks when the following buttons are lit: NUMBER keys
(0 – 9), TIME SCAN, CANCEL and MENU.
When Using The Illumi-Guide Feature
● Buttons light or blink on the remote control for approximately 10 seconds. If the button or buttons extinguish during timer programming, press ILLUMI GUIDE and the button or buttons previously lit or blinking come back on. If the button or buttons do not re-light or start blinking again, press MENU as many times as necessary to return to the normal screen and extinguish all illuminated buttons, and re-perform the timer programming procedure from the beginning.
● If for some reason the remote control's signal is not received by the VCR, press MENU as many times as necessary to return to the normal screen and extinguish all illuminated buttons, and re-perform the timer programming procedure from the beginning.
•
•
•
•
•
•
•
•
•
•
NUMBER
MENU
1
4
7
NUMBER "8"
2
5
8
0
3
6
9
CH
OK
TIME SCAN
EXAMPLE
If you program the VCR to timer record a show on September 6 on channel 40 from 12:00 noon to 1:00 PM in SP mode, the screen will look like this:
PROGRAM 1
DATE 9/ 6 SUN
START 12:00 PM
STOP 1:00 PM
CHANNEL 40 SP
PRESS NUMBER KEY(0-9)
OR (
5,∞), THEN (OK)
PRESS (MENU) TO END
8
NUMBER "9"
TIMER
NOTES:
● To disengage the timer before recording starts, press TIMER again. Pressing once more re-engages it.
● In case of a power failure after programming, the VCR’s memory backup keeps your selections for approximately 10 minutes.
● If you select "PROGRAM SET" without having set the date and time, an error message appears. Follow its instructions.
● If you enter a start time that has already passed, "ERROR" appears on the screen and flashes.
● Programs that start after midnight must have the next day’s date.
5
6
7
8
47
SET PROGRAM
INFORMATION
Press the appropriate NUMBER keys to set the date, start/stop time and channel number. Press CH
5∞ or
TIME SCAN
5∞ to set AM/PM and tape speed. Press
OK after AM/PM, channel number and tape speed settings. The next setting that can be set begins flashing.
● Any information comprised of 1 digit (except the channel number) should have a "0" entered before it.
● It is possible to set all information using the CH5∞ or
TIME SCAN
5∞ button.
(In this case, press OK after each setting.) Do not use the CH
∞ or TIME SCAN ∞ button to set the date.
● If you are using the Illumi-Guide feature, OK blinks when the following buttons are lit: NUMBER keys
(0 – 9), TIME SCAN, CANCEL and MENU.
NOTES:
● To timer-record a program received with a cable box or DSS receiver, directly enter the channel that the cable box or the DSS receiver receives it on.
● If a DSS receiver is used, cable channels 100 to 199 cannot be timer-recorded. For timer-recording of these channels, set the "DSS RECEIVER OUTPUT" to
"OFF". (
Z
pg. 23)
** You can record selected programs at the same time every weekday, or once a week. Before entering the month, press NUMBER key “8” (DAILY) or “9”
(WEEKLY). Either "DAILY" or "WEEKLY" appears.
Press again and "DAILY" or "WEEKLY" disappears.
For weekly recording, the desired date for the day of the week must be entered.
MAKE CORRECTIONS
To change any of the settings, press OK or TIME SCAN
™
£ until the item you want to change begins blinking. Then set as in step 5.
● If you are using the Illumi-Guide feature, OK blinks when the following buttons are lit: NUMBER keys
(0 – 9), TIME SCAN, CANCEL and MENU.
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
● Press just once to access the Auto Timer screen
(
Z
pg. 49).
● If you are using the Illumi-Guide feature, all buttons go out.
ENGAGE TIMER MODE
Press TIMER. The VCR turns off automatically.
● After timer recording is completed, the VCR’s power goes off automatically.
● You can program the timer while a regular recording is in progress; the on-screen menu will not be recorded.
● If the end of tape is reached during timer recording, the cassette is automatically ejected.
● When timer-recording cable channels received through a
Cable Box, be sure to keep the Cable Box set to ON.
● When timer-recording satellite channels received through a
DSS receiver, be sure to keep the DSS receiver set to ON.
48
•
•
•
•
•
•
•
•
•
•
POWER
CANCEL
1
4
7
2
5
8
0
3
6
9
CH
TIMER
MENU
OK
TIME SCAN
8
TIMER RECORDING (cont.)
Check And Cancel Programs
DISENGAGE TIMER
Press TIMER, then press POWER.
1
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
2
3
ACCESS PROGRAM SET
SCREEN
Press CH
5∞ or TIME SCAN 5∞ to place the arrow next to "PROGRAM SET", then press OK.
4
CHECK PROGRAM INFOR-
MATION
Press CH
5∞ or TIME SCAN 5∞ to check the programs in succession.
To Cancel A Program . . .
5
CANCEL A PROGRAM
Press CANCEL.
● Repeat steps 4 and 5 as many times as necessary.
6
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary. If there are still programs remaining, go to step 7.
RE-ENGAGE TIMER
Press TIMER again.
7
•
•
•
•
•
•
•
•
•
•
MENU
1
4
7
2
5
8
0
3
6
9
CH
TIMER
OK
TIME SCAN
8
49
Auto Timer
When the Auto Timer is set to ON the timer is automatically engaged when the VCR's power is turned off and automatically disengaged when the VCR is powered back on.
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
1
2
ACCESS FUNCTION SET
SCREEN
Place the arrow next to "FUNCTION SET" by pressing
CH
5∞ or TIME SCAN 5∞, then press OK.
3
ACCESS AUTO TIMER
SCREEN
Place the arrow next to "AUTO TIMER" by pressing
CH
5∞ or TIME SCAN 5∞, then press OK. Now skip to step 2 of the procedure below.
Or, during on-screen timer programming ...
1
2
ACCESS AUTO TIMER
SCREEN
In step 7 in the VCR Plus+ Timer Programming procedure (
Z
pg. 45) or in step 7 in the On-Screen Timer
Programming procedure (
Z
pg. 47), press MENU.
SELECT MODE
Place the arrow next to your choice ("ON" or
"OFF") by pressing CH
5∞ or TIME SCAN
5∞.
AUTO TIMER
=ON
OFF
PRESS (
5,∞) TO SELECT
PRESS (MENU) TO END
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
3
NOTE:
For safety, when AUTO TIMER is set to “OFF”, all other VCR functions are disabled while the Timer mode is engaged. To disengage the timer, press TIMER.
50
Instant Timer
Recording
(ITR)
•
•
•
•
•
•
•
•
•
•
I T R
VIDEO SP
8
R E C
TIMER RECORDING (cont.)
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-min. increments), and shuts the VCR off after recording is finished.
START RECORDING
Press REC on the front panel.
1
2
ENGAGE ITR MODE
Press REC again. ITR blinks and 0:30 appears on the front display panel.
3
SET RECORDING
DURATION
If you want to record for more than 30 minutes, press
REC to extend the time. Each press extends recording time by 30 minutes.
NOTES:
● You can only perform ITR using the REC button on the VCR's front panel.
● After you set the time, the previous display reappears.
● To check the remaining time, press REC once during recording and the remaining time will be displayed for about 5 seconds. Be careful not to press REC again within these 5 seconds, or you will round the recording time up to the next
30 minute increment.
EDITING
Edit To Or
From Another
VCR
Player
Your VCR
VIDEO OUT
Recorder
VIDEO IN
AUDIO OUT
AUDIO IN
Another VCR
51
You can use your VCR as the player or the recorder.
1
2
MAKE CONNECTIONS
Connect an AV cable between the player’s VIDEO OUT and AUDIO OUT connectors and the recorder’s VIDEO
IN and AUDIO IN connectors.
● When using your VCR as the recorder and a monaural
VCR as the player, connect the player’s AUDIO OUT connector to the AUDIO IN L connector on the recorder.
LOAD CASSETTES
Insert the playback cassette into the player and the cassette to be recorded on into the recorder.
3
SET RECORDER’S INPUT
MODE
Set to AUX. With this VCR, press NUMBER key “0” (AU appears on the front display panel in place of a channel number).
NOTE:
When using this VCR as the recorder, make sure to select
"FRONT" or "REAR" (depending on which input connectors you use) at the Aux Input Screen. (To select the correct AUX input connector, follow steps 4, 5, 9 – 11 from the "Edit
From A Camcorder" section,
Z
pg. 52.)
START PLAYER
Set to its play mode.
4
NOTE:
If the player is equipped with a superimpose/OSD disable feature then set "SUPERIMPOSE" to OFF before pressing PLAY (
Z
pg. 30).
START RECORDER
Set to its record mode.
5
NUMBER "0"
1
4
7
2
5
8
0
3
6
9
52
Edit From A
Camcorder
Recorder
Your VCR
8
•
•
•
•
•
•
•
•
•
•
AUDIO
IN
To rear panel PAUSE/SPECIAL
FUNCTION connector
Mini-plug cable (not supplied)
(JVC camcorder only)
VIDEO
IN
VIDEO
OUT
Camcorder
AUDIO OUT
EDIT
Player
NUMBER "0"
1
4
7
2
5
8
0
3
6
9
CH
MENU
OK
TIME SCAN
EDITING (cont.)
You can use a camcorder as the player and your VCR as the recorder.
1
MAKE CONNECTIONS
Connect an AV cable between the camcorder’s VIDEO
OUT and AUDIO OUT connectors and your VCR’s
VIDEO IN and AUDIO IN connectors.
● When a Master Edit Control-equipped JVC camcorder is used, the camcorder is capable of controlling your VCR.
The mini-plug cable is a mono 3.5 mm mini-plug to mono 3.5 mm mini-plug connector.
● If connecting to a camcorder with a monaural output, connect the audio output connector on the camcorder to AUDIO IN L of the VCR.
LOAD A CASSETTE
Insert the cassette to be recorded on into the recorder.
2
SET RECORDER’S INPUT
MODE
Press NUMBER key “0” to set to AUX.
3
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
4
5
ACCESS FUNCTION SET
SCREEN
Press CH
5∞ or TIME SCAN 5∞ to place the arrow next to “FUNCTION SET”, then press OK.
6
If you’re using a JVC Master Edit Control-equipped camcorder — step 6
If not — step 9
ACCESS SPECIAL
FUNCTION SCREEN
Press CH
5∞ or TIME SCAN 5∞ to place the arrow next to “SPECIAL FUNCTION”, then press OK.
7
SELECT MODE
Press CH
5∞ or TIME SCAN
5∞ to place the arrow next to “R.A. EDIT/PAUSE”.
SPECIAL FUNCTION
=R.A. EDIT/PAUSE
AV COMPU-LINK
PRESS (
5,∞) TO SELECT
PRESS (MENU) TO END
•
•
•
•
•
•
•
•
•
•
MENU
1
4
7
2
5
8
0
3
6
9
CH
OK
TIME SCAN
8
53
RETURN TO FUNCTION
SET SCREEN
Press MENU.
8
9
10
13
ACCESS AUX INPUT
SCREEN
Press CH
5∞ or TIME SCAN 5∞ to place the arrow next to “AUX INPUT”, then press OK.
SELECT INPUT
If you are connecting the
AV cable to the AV connectors on the front of the VCR, place the arrow next to "FRONT" by pressing CH
5∞ or TIME
SCAN
5∞. If you are connecting the AV cable to the AV connectors on the
AUX INPUT
=FRONT
REAR
PRESS (
5,∞) TO SELECT
PRESS (MENU) TO END
back of the VCR, place the arrow next to "REAR" by pressing CH
5∞ or TIME SCAN 5∞.
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
11
12
START PLAYER
Set the camcorder to its play mode.
NOTE:
If the camcorder is equipped with a superimpose/OSD disable feature then set its superimpose or display feature to OFF before pressing play.
START RECORDER
Set your VCR to its record mode.
● If you are using a Master Edit Control-equipped JVC camcorder, it can put the recorder automatically into
Record mode. (Refer to camcorder's instruction manual.)
54
Assemble
Editing
•
•
•
•
•
•
•
•
•
•
SP/EP
REC
PAUSE
1
4
7
2
5
8
0
3
6
9
PAUSE
8
EDITING (cont.)
Assemble Editing adds one recorded scene to another in succession.
To use your VCR as the recorder ...
1
LOAD CASSETTES
Insert the original cassette in the player, and the recording cassette in the recorder.
SET TAPE SPEED
Set to "SP" or "EP" by pressing the SP/EP button.
2
ENGAGE RECORD-
STANDBY MODE
Press and hold PAUSE, and press REC.
3
4
5
FIND EDIT START POINT
Play back the original tape until you reach the scene to be edited.
START EDITING
When you reach the scene on the original tape to be edited, press PLAY to initiate the recorder’s record mode.
STOP EDITING
Press PAUSE to pause the tape in the recorder.
6
CONTINUE EDITING
Repeat steps 4 through 6 to add additional scenes.
7
NOTE:
Assemble Editing is also possible using your VCR as the playback deck.
Audio Dubbing
55
Audio dubbing replaces the normal audio sound of a previously recorded tape with a new soundtrack. Use your VCR as the recorder.
Normal audio track
Pre-recorded tape
A. DUB
Video/Hi-Fi audio track
8
•
•
•
•
•
•
•
•
•
•
STOP
Audio component
(CD player etc.)
NOTES:
● When monitoring the sound during Audio Dubbing, the normal soundtrack is automatically selected. If you wish to hear the Hi-Fi or mixed sound (Hi-Fi + Normal soundtracks), refer to the "Select The Soundtrack" section (
Z
pg. 29) and select the soundtrack you wish to hear.
● Audio dubbing stops automatically when the counter reaches
"0
H
00
M
00
S
", and the VCR enters the Play mode. Check the counter reading before dubbing.
● Audio dubbing is also possible using the rear AUDIO IN connectors. When using these connectors, make sure to select
"REAR" at the Aux Input screen. To select the correct Aux
Input connector, follow steps 4, 5, 9 – 11 from the "Edit From
A Camcorder" section
Z
● Audio dubbing cannot be performed on a cassette that has
The Soundtrack" section (
pg. 52.
had its record safety tab removed.
● When playing back an audio-dubbed tape, refer to the "Select
Z
pg. 29) to select the soundtrack you wish to hear.
● It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.
Audio-dubbed tape
1
2
3
4
5
6
MAKE CONNECTIONS
Connect an audio component to the AUDIO IN L + R connectors on the VCR's front panel. *When connecting monaural equipment, use only the VCR's AUDIO
IN L connector.
SET INPUT MODE
Press NUMBER key "0" on the remote control. "AU" appears in place of a channel number.
● Be sure to select "FRONT" at the AUX Input Screen.
(To select the correct AUX Input connector, follow steps 4, 5, 9 – 11 from the "Edit From A Camcorder" section,
Z
pg. 52.)
LOCATE START POINT
Press PLAY to start playback of the tape in your VCR, and press PAUSE when you find the point where you want to start dubbing.
ENGAGE AUDIO DUBBING
Press A. DUB.
● Your VCR enters the Audio Dubbing Pause mode.
(REC blinks, PLAY and PAUSE light up on the front display panel.)
START DUBBING
Engage the audio component's Play mode, then press
PLAY to start the tape in your VCR. Audio dubbing begins at this point.
● REC blinks and PLAY is displayed on the front display panel.
● To stop dubbing temporarily, press PAUSE. Press
PLAY to resume dubbing.
END AUDIO DUBBING
Press STOP to stop the tape in your VCR, and engage the audio component's Stop mode.
56
Insert Editing
Recorder
PAUSE
TIME SCAN SHUTTLE
Your VCR
8
•
•
•
• • •
•
•
•
•
EDITING (cont.)
Insert editing replaces part of the recorded scene with new material. Both the picture and Hi-Fi audio soundtrack are replaced with new ones, while the normal audio soundtrack remains unchanged. If you wish to change the normal audio track as well, use the audio dubbing function simultaneously.
Use your VCR as the recorder.
Source tape
Audio signal
Video signal
Player
Another VCR
C.RESET
1
4
7
2
5
8
0
3
6
9
PAUSE
Recorded tape
Before insert editing
Normal audio track
1
2
3
After insert editing
Video/Hi-Fi audio track
MAKE CONNECTIONS
Connect the player's VIDEO OUT and AUDIO OUT connectors to your VCR's VIDEO IN and AUDIO IN on the front panel.
SET INPUT MODE
Press NUMBER key "0". "AU" appears in place of a channel number.
● Be sure to select "FRONT" at the Aux Input screen.
(To select the correct AUX input connector, follow steps 4, 5, 9 – 11 from the "Edit From A Camcorder" section
Z
pg. 52).
LOCATE END POINT
Load the recording cassette into your VCR, and play it back to determine the edit-out point (the end of the segment to be replaced) using the JOG/TIME SCAN
SHUTTLE controls or TIME SCAN ™£ and PAUSE.
RESET THE COUNTER
Press C.RESET to change the counter display to
"0
H
00
M
00
S
".
4
5
LOCATE START POINT
Determine the edit-in point (the beginning of the segment to be replaced) using the JOG/TIME SCAN
SHUTTLE controls or TIME SCAN ™£ and PAUSE.
● Be sure to engage the Still mode at the edit-in point.
TIME SCAN
k i
•
•
•
•
•
•
•
•
•
•
C.RESET
1
4
7
2
5
8
0
3
6
9
PLAY
8
57
6
7
8
ENGAGE INSERT EDITING
Press INSERT.
● Your VCR enters the Insert-Pause mode. (REC, PLAY and PAUSE light up on the front display panel.)
● The TV screen changes from the still picture to the input source you are going to record.
START EDITING
Load the source cassette and play back the segment that is to be inserted. When you reach the start of the section of the source tape that you wish to insert, press
PLAY to start the tape in your VCR; Insert Editing begins at this point.
● PLAY and REC are displayed on the front display panel.
END INSERT EDITING
At counter "0
H
00
M
00
S
", Insert Editing will stop automatically while the tape continues running in the Play mode. if you wish to stop Insert Editing before the specified edit-out point, press C.RESET.
FOR AV INSERT EDITING
If you want to replace the picture, Hi-Fi audio soundtrack and normal audio soundtrack all at the same time...
In step 6 above, after you press INSERT, press A. DUB. also.
(REC and PLAY blink and PAUSE lights up on the display panel.)
NOTES:
● Suitable leads can be obtained from your dealer.
● Insert editing is not possible with cassettes whose safety tab has been removed.
● In insert editing, the recording speed (SP/EP) is determined by the previous recording to be replaced. If the previous recording's speed changes within a single edit, the inserted picture will be distorted at the switching point.
● A small portion of the recording which precedes an insert edit may become erased.
● Insert Editing is also possible using the rear connectors.
When using these connectors, be sure to select "REAR" at the
Aux Input screen. To select the correct AUX Input connector, follow steps 4, 5, 9 – 11 from the "Edit From A Camcorder" section,
Z
pg 52.
58
EDITING (cont.)
This function makes it easier to create edited videos when your
Random As-
VCR is used as the source player in combination with another
VCR equipped with a Remote PAUSE Connector. You can preprogram up to 8 scenes or “cuts” for automatic editing in the sequence you have specified.
semble Editing
MAKE CONNECTIONS
Connect your VCR’s VIDEO OUT and AUDIO OUT
PAUSE/
SPECIAL
FUNCTION
1
connectors to the VIDEO IN and AUDIO IN connectors on the recording deck, and connect your VCR’s PAUSE/
SPECIAL FUNCTION connector to the PAUSE connector on the recording deck.
Player
Your VCR
8
● If the recording deck doesn’t have a PAUSE connector, connect to the R.A. EDIT connector instead.
● The Mini-plug cable is a mono 3.5 mm mini-plug to mono 3.5 mm mini-plug connector.
•
• • •
•
•
•
•
•
•
•
Audio signal
Recorder
•
•
•
•
•
•
•
•
•
•
•
Another VCR
(w/PAUSE connector)
REMOTE
PAUSE
CH
Video signal
STOP
Mini-plug Cable
(Not supplied)
8
2
3
4
PREPARE FOR EDITING
Perform steps 2 – 8 on page 52, “Edit From A
Camcorder”.
-ERROR-
CHOOSE SPECIAL FUNCTION
ON MAIN MENU AND SELECT
R.A. EDIT/PAUSE
NOTE:
If you mistakenly select
“AV COMPU LINK” in step 7 on page 52, an error
BEFORE YOU BEGIN
R.A. EDIT
PRESS (MENU) TO MAIN MENU
message appears when you finish step 6. Make sure “R.A. EDIT/PAUSE” is selected before you continue.
LOAD SOURCE CASSETTE
Insert the source cassette into your VCR.
● To return to the normal screen from the Function screen, press MENU.
START SOURCE PLAYBACK
Press PLAY.
5
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary to bring up the
Main Menu screen.
CANCEL
1
4
7
2
5
8
0
3
6
9
CH
PLAY
6
ACCESS R.A. EDIT SCREEN
Place the arrow next to
“R.A. EDIT” by pressing
CH
5∞ or TIME SCAN5∞, then press OK.
● The screen is superimposed on the video playback in step 7.
MAIN MENU
PROGRAM SET
FUNCTION SET
TUNER SET
CUSTOM SET
VIDEO CALIBRATION
=R.A. EDIT
PRESS (
5, ∞), THEN (OK)
PRESS (MENU) TO END
C.MEMORY
OK
TIME SCAN
MENU
7
8
LOCATE EDIT-IN POINT
Find the point on the source tape from where you want the edited scene to begin by pressing TIME SCAN
™£
, or using JOG/
TIME SCAN SHUTTLE
then press OK.
R.A. EDIT
=1
2
3
4
5
6
7
8
EDIT MODE
TTL 0:00:00 CNT 0:00:00
● The edit-in point is registered in memory and appears on the screen.
● You can also perform an Index Search (if index marks have been previously recorded on the tape at the desired points
Z
pg. 31) to find the points you want, but this will result in reduced accuracy.
LOCATE EDIT-OUT POINT
Find the point where you want the edited scene to end by pressing TIME SCAN
™£
, or using JOG/
TIME SCAN SHUTTLE then press OK.
R.A. EDIT
=1
0:02:23
2
3
4
5
6
7
8
TTL 0:00:00
EDIT MODE
CNT 0:02:23
● The edit-out point is registered in memory and appears on the screen.
● The total time of the edited scenes is displayed to the right of "TTL".
● Repeat steps 7 and 8 for each additional scene.
=2
3
R.A. EDIT
1 0:02:23
4
5
6
7
8
TTL 0:00:28
EDIT MODE
0:02:51
CNT 0:02:51
PREPARE RECORDING DECK
Engage its Record-Standby mode.
9
10
START R.A. EDIT
Press R.A. EDIT START on the VCR or C.MEMORY on the remote control.
● Automatic editing begins; all the specified scenes are copied to the recording deck in the order they were registered.
● The on-screen display remains while your VCR searches for each scene (blinking cursor indicates scene currently being searched for), but disappears during actual editing.
● During scene search, the recording deck automatically enters its Record-Standby mode. "SEARCHING" appears on the screen.
● When all registered scenes have been edited, your
VCR enters the Still mode, the recording deck enters its Record-Standby mode, and the cursor blinks at the next available number.
59
11
END R.A. EDIT
Press MENU as many times as necessary to return to the normal screen, and engage the Stop mode for the both
VCRs.
NOTES:
● You can also monitor the sound when searching for scenes you want to edit in steps 7 – 8. Since you can hear the soundtrack during selection, you can avoid abrupt or unnatural sounding scene-to-scene transitions. The sound that is heard, however, is not TimeScan Audio.
● When editing, there may be a discrepancy of about 2 seconds on the source tape between the locations you chose as edit-in/out points and the locations the VCR recognizes as those points.
● There are no limitations for R.A. Edit list (such as repeat segments, negative counter values, segments out of order).
Only the start-stop sequence has to be in the normal play direction.
● For any scene, the edit-out point must have a counter reading that is at least 1 second after the corresponding edit-in point. Any less than 1 second and the edit-out point will not be registered.
● Since the source VCR prerolls during Random Assemble
Editing, there must be at least 15 seconds worth of recorded material prior to any edit-in point on the source tape.
● If the search time for an edit-in point exceeds 5 minutes, the recording deck enters its Stop mode and editing will not take place.
To Make Corrections . . .
. . . during step 7 or 8, you can cancel registered in and out points by pressing CANCEL on the remote control. Each time you press, the preceding point is erased.
● If, for example, you have registered 5 sets of in and out points and want to reset the first set, you have to press CANCEL until all points after the first set have been erased. Reenter them after you've repaired the first set of points.
Memory Capacity
Random Assemble Editing shares memory space with the VCR's timer. If there are programs occupied by timer-recording data, those spaces cannot be used to register edit-in and -out points — meaning you won't be able to edit
8 scenes.
R.A. EDIT
PROGRAM FULL
TTL 0:00:00
EDIT MODE
CNT 0:00:00
● When all 8 programs are full, "PROGRAM FULL" appears on the R.A. EDIT screen.
● To cancel a program, see page 48.
RM-V403U Multi-Brand R.A. Edit Controller
(Not supplied)
By connecting this controller to your VCR's R.A. EDIT connector, you can perform Random Assemble Editing in combination with a second non-JVC VCR. The controller is compatible with various major VCR brands. For compatible systems and availability, please consult your JVC dealer.
60
POWER
NUMBER
VOL. +/-
1
4
7
2
5
8
0
3
6
9
ENTER
CH
TV/CABLE/VCR
TV/VIDEO
SPECIAL FEATURES
TV Multi-Brand Remote
Control
The VCR's remote control can control several functions on JVC remote control TVs and on the brands of remote control TVs listed below.
TURN ON THE TV
Turn the power on using the TV's remote control.
1
2
SET REMOTE CONTROL
MODE
Set the TV/CABLE/VCR switch on the VCR's remote control to TV.
3
4
SET TV BRAND CODE
Refer to the chart below. While holding down POWER on the VCR's remote control, enter your TV’s brand code using the NUMBER keys, then press STOP.
● Once you have set the remote control to operate the
TV, you don’t have to repeat this step until you replace your remote control’s batteries.
● PANASONIC has two codes. If the TV does not function with one code, try entering the other.
OPERATE TV
First, press POWER on the remote to see if the TV’s power goes off as it should. If it does, try other operations.
● The POWER, TV/VIDEO, CH5∞, VOL +/– and
NUMBER keys on the remote can all be used to operate the TV. *For some brands of TV, you must press ENTER after having pressed the NUMBER keys.
● To return the remote to VCR control, set the TV/
CABLE/VCR switch to VCR.
NOTE:
Depending on the kind of TV, there may be cases where some or all functions cannot be operated using the remote control.
TV BRAND NAME
JVC
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
SHARP
SONY
TOSHIBA
ZENITH
HITACHI
SAMSUNG
SANYO
SEARS
12
13
13
07
08
09
10
BRAND CODE
01
02
03
04, 11
05
06
NUMBER
1
4
7
2
5
8
0
3
6
9
POWER
ENTER
CH
TV/CABLE/VCR
CABLE BOX BRAND NAME BRAND CODE
CURTIS 09, 10
GEMINI
GENERAL INSTRUMENTS
08
01, 02, 03, 04, 05, 06, 07, 08
HAMLIN
JERROLD
OAK
PANASONIC
15, 16, 17, 18
01, 02, 03, 04, 05, 06, 07, 08
19, 20, 21
24, 25, 26
PIONEER
RCA
REGAL
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
SPRUCER
TELEVIEW
TOCOM
VIDEOWAY
ZENITH
13, 14
24, 25, 26
15, 16, 17, 18
08, 13
09, 10
19, 20, 21
08, 13
24, 25, 26
08, 13
22, 23
11, 12
11, 12
61
Cable Box Multi-Brand
Remote Control
The VCR's remote control can control functions on the brands of cable boxes listed below. Some cable box brands have more than one code. If your cable box does not function with a specified code, try other codes.
TURN ON THE CABLE BOX
Turn the power on using the cable box’s remote control.
1
2
SET REMOTE CONTROL
MODE
Set the TV/CABLE/VCR switch on the VCR’s remote control to CABLE.
3
4
ENTER CABLE BOX BRAND
While holding down POWER on the VCR's remote control, use the NUMBER keys to enter the cable box brand number from the chart below and then press
STOP.
● Once you have set the remote control to operate the cable box, you don't have to repeat this step until you replace the remote control's batteries.
OPERATE CABLE BOX
First, press POWER to see if the cable box’s power goes off as it should. If it does, try other functions (CH
5∞ and the NUMBER keys can be used to operate the cable box).
● For some brands of cable box, you must press ENTER after having pressed the NUMBER keys.
● To return the remote to VCR control, set the TV/
CABLE/VCR switch to VCR.
NOTES:
● You must set the cable box brand for your remote control and the cable box brand for your Controller (
Z
pg. 17) separately.
The list of cable box brands that can be controlled by your remote control is different from the list of brands that can be controlled by your cable box controller.
● It is possible that the remote control will not operate your cable box even if the cable box’s channels automatically change during timer recording using the Controller.
62
A/B CODE
POWER
1
4
7
2
5
8
0
3
6
9
TIMER
SPECIAL FEATURES (cont.)
Control Two JVC VCRs
The supplied remote control is capable of controlling two JVC
VCRs independently using the A/B CODE switch. You can set this VCR so it responds to remote commands only when the switch is set to B, and another VCR so it responds to commands when the switch is set to A. The switch is preset to A because this VCR normally responds to A-code signals. You can easily modify this VCR to accept B-code commands.
UNPLUG VCR'S POWER
CORD
Unplug from the AC outlet.
1
SET A/B CODE SWITCH
Set the A/B CODE switch on the remote control to B.
2
PLUG IN POWER CORD
Plug back in to the AC outlet.
3
4
TURN VCR POWER ON
Press POWER on the remote.
● You can control two VCRs with the same remote control by toggling the slide switch between A and B.
The VCR will now respond only to B-code commands.
Child Lock
This feature allows you to prevent the operation of the VCR.
TURN VCR POWER ON
Press POWER.
1
2
ENGAGE CHILD LOCK
Press and hold POWER on the remote control until the
Child Lock indicator ("—") appears on the front display panel.
● To cancel Child Lock, press and hold POWER on the remote to turn the VCR on. During timer recording, pressing TIMER also cancels Child Lock.
NOTES:
● When Child Lock is engaged, make sure to keep the remote control out of the reach of children.
● Timer recording of programs that were previously set can be performed while the Child Lock is engaged. The feature remains in effect after the recording is finished.
TROUBLESHOOTING
63
Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your VCR off for repair.
POWER
SYMPTOM
1. The power won’t come on.
2. The clock works, but the VCR’s power won’t come on.
3. The remote control won’t function.
POSSIBLE CAUSE
● The power cord is disconnected.
● The TIMER mode is engaged with
Auto Timer set to "OFF" (
Z
pg. 49).
● The batteries are discharged.
● The A/B CODE switch is in the wrong position.
● The TV/CABLE/VCR switch is in the wrong position.
CORRECTIVE ACTION
Connect the power cord.
Press TIMER to disengage.
Replace the dead batteries with new ones.
(
Re-perform the A/B Code setting
Z
pg. 62).
Set the switch to the position corresponding with the unit you want to operate.
TAPE TRANSPORT
SYMPTOM
1. The cassette gets stuck partway during loading, and is ejected.
2. The tape stops during rewind or fast forward.
POSSIBLE CAUSE
● The cassette was inserted incorrectly.
● The Counter Memory indicator
(“M”) is lit on the front display panel.
CORRECTIVE ACTION
Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR. Then insert the cassette
Press C.MEMORY to disengage the
Counter Memory mode and extinguish the indicator.
PLAYBACK
SYMPTOM
1. The tape is running but the picture won’t appear.
2. Noise appears during visual search.
3. Breaks are noticeable in Hi-Fi soundtrack.
4. The playback picture is blurred or interrupted, even though TV broadcasts are clear.
5. The Hi-Fi soundtrack cannot be heard.
POSSIBLE CAUSE
● If you’re using the RF OUT connection (
Z
pg. 6), the channel selector on the TV is set incorrectly.
● If you’re using the AV connection
(
Z
pg. 6), the TV receiver is set to the wrong mode.
● This is normal.
● Automatic tracking is engaged.
● The video heads may be dirty.
● The AUDIO MONITOR option at the Function Set screen was set incorrectly.
CORRECTIVE ACTION
Set the channel selector to channel 3 or 4.
Set the TV receiver to its AV mode.
(
Engage and adjust tracking manually
Z
pg. 28).
The heads must be cleaned. Consult your JVC dealer (
Z
pg. 71).
(
Set AUDIO MONITOR to "HI-FI"
Z
pg. 29).
CONTINUED ON NEXT PAGE.
64
RECORDING
SYMPTOM
1. Recording won’t start.
TROUBLESHOOTING (cont.)
2. TV broadcasts won’t record properly.
3. Tape-to-tape editing won’t work.
POSSIBLE CAUSE
● There’s no cassette loaded.
● The loaded cassette has had its record safety tab removed.
● The VCR has been set to its AUX mode by mistake.
●The VCRs or the camcorder and the
VCR have been incorrectly connected.
● The power to one or more of the units has not been turned on.
● The recorder’s input mode has been set incorrectly.
CORRECTIVE ACTION
Insert a cassette.
Remove the cassette and cover the hole with adhesive tape, or load a cassette on which the record safety tab is intact.
Set the VCR to the appropriate channel.
Refer to the directions and the illustration under “Edit To Or From
Another VCR” (
Z
pg. 51) or “Edit
From A Camcorder” (
Z
pg. 52) and properly connect the units.
Make sure the power to all units is on.
Set the recorder’s input mode to AUX and select "FRONT" or "REAR" at the
Aux Input Screen (
Z
pg. 53).
TIMER RECORDING
SYMPTOM
1. Timer recording won’t work.
POSSIBLE CAUSE
● The clock and/or the timer have been set incorrectly.
● The timer is not engaged.
● The VCR has not been set up properly.
2. On-screen timer programming won’t work.
3. TIMER and ] on the front display panel won’t stop blinking.
4. The cassette is automatically ejected, and TIMER and ] on the front display panel won’t stop blinking.
5. TIMER blinks for 10 seconds and the timer mode is disengaged.
● Timer recording is in progress.
● The timer is engaged but there’s no cassette loaded.
● The loaded cassette has had its record safety tab removed.
6. The cassette is automatically ejected, the power shuts off and
TIMER and ] won’t stop blinking.
7. Cable channels are not automatically switched during timer recording.
● TIMER has been pressed when there are no programs in memory, or the timer record program information has not been programmed correctly.
● The end of tape was reached during timer recording.
● The Cable Box Controller is not properly connected to the VCR.
● The output channel selected in the
Cable Box Output screen is incorrect.
● The cable box’s power is off.
CORRECTIVE ACTION
Check or re-perform the clock/timer settings to ensure correctness.
Press TIMER and check to make sure that TIMER appears on the front display panel.
Re-perform the set-up procedures.
Make sure you have compensated for
Guide Channel and VCR or cable
( box channel number mismatches
Z
pg. 19).
Timer programming can’t be performed when timer recording is in progress.
Wait until it finishes.
Load a cassette with the record safety tab intact, or with the hole covered with adhesive tape.
Remove the cassette and cover its hole with adhesive tape, or replace it with a cassette on which the safety tab is intact.
Check the programmed data and reprogram as necessary, then press
TIMER again.
The program may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire program.
Connect the Cable Box Controller correctly (
Z
pg. 15).
After confirming your cable box’s output channel number, re-access the
Cable Box Output screen and select the correct number (
Z
pg. 17).
Make sure the power is on before timer recording starts.
(
Set "CABLE BOX OUTPUT" to "OFF"
Z
pg. 17).
Re-perform the VCR Plus+ setup procedure (
Z
pg. 19).
Wait until a space in memory clears, or cancel unnecessary program information (
Z
pg. 48).
65
8. Timer recording begins as scheduled, but the channel is always incorrect.
9. We moved, and now VCR Plus+ doesn’t work properly.
10.“PROGRAM FULL” is displayed on the VCR Plus+ screen.
OTHER PROBLEMS
SYMPTOM
1. When scanning channels, some of them are skipped over.
2. The channel can’t be changed.
● Even though you don't use an external Cable Box, "CABLE BOX
OUTPUT" is set to "ON".
● The receivable stations in the new area are received on different channels than those in the previous area.
● All 8 programs of the VCR’s timer memory are used.
POSSIBLE CAUSE
● Those channels have been preset to be skipped.
● Recording is in progress.
3. The remote control won’t operate my TV.
4. The remote control won't operate my cable box.
5. Even though Auto or Semi-Auto clock setting has been selected, the clock is incorrect.
● The TV/CABLE/VCR switch is set to a position other than TV.
● The TV/CABLE/VCR switch is set to a position other than CABLE.
● The clock setting data received from the Host Channel is incorrect.
CORRECTIVE ACTION
If you need the skipped channels, restore them (
Z
pg. 14).
Press PAUSE to pause the recording, change channels, then press PLAY to resume recording.
Set the switch to TV.
Set the switch to CABLE.
Select a different Host Channel during
( the Semi-Auto setting procedure
Z
pg. 10), or perform the Manual setting procedure (
Z
pg. 11).
ATTENTION:
This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the power off and unplug the power cord. Then plug it in again and switch power on. Take out the cassette. After checking the cassette, operate the unit as usual.
66
PLAYBACK
Q. What happens if the end of the tape is reached during playback or search?
A. The tape is automatically rewound to the beginning.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. Can the VCR indefinitely remain in the still mode?
A. No. It stops automatically after 5 minutes to protect the heads.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. During search, slow, still and frame-by-frame playback, I can’t hear any audio. What’s the problem?
A. This is normal.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. During search, still and frame-by-frame playback, the picture is intermittent. What’s the cause?
A. Picture loss occurs when these types of playback are attempted with a tape recorded in LP mode. Pressing
PLAY to return to normal playback will restore the picture.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. When returning from multi-speed search to normal playback, the picture is disturbed. Should I be concerned about this?
A. No, it is normal.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. Noise bars appear during multi-speed search. What’s the problem?
A. This is normal.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. Other than preventing further recording, what effect does removing the safety tab have?
A. It disables marking of index codes.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. Sometimes, during Index Search, the VCR can’t find the program I want to see. Why not?
A. There may be index codes too close together.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. During playback, on-screen operational indicators sometimes jitter. Why does this happen?
A. If the condition of the tape being played back is not good, jittering of the video (including on-screen indicators) may occur.
QUESTIONS AND ANSWERS
RECORDING
Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the new recording. Why does this happen?
A. This is normal. It reduces distortion at the pause and resume points.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. Can the VCR indefinitely remain in the Record-Pause mode?
A. No. The VCR automatically goes to its Stop mode after 5 minutes to protect the heads. When paused during Instant Timer Recording (ITR), the VCR shuts off automatically after 5 minutes.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. What happens if the tape runs out during recording?
A. The VCR automatically rewinds it to the beginning.
TIMER RECORDING
Q. REC and TIMER remain lit on the front display panel.
Is there a problem?
A. No. This is a normal condition for a timer recording in progress.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. Can I program the timer while I’m watching a tape or a TV broadcast?
A. You won’t see the picture as it is replaced by the onscreen menu, but the audio from the program or tape you’re viewing is present.
INDEX
List Of Terms
This guide serves as a quick way to locate frequently used terms and on-screen display names. The first page on which the term appears is listed. Most terms appear more than once in the instruction manual.
67
A
A/B Code ....................................................................62
Active Video Calibration .............................................38
Add Channel ...............................................................14
AFC .............................................................................14
Audio Dubbing ...........................................................55
Audio Monitor ............................................................29
Auto Channel Setting ..................................................13
Auto Clock Setting ...................................................... 11
Auto Daylight Saving Time .......................................... 11
Auto Timer ..................................................................49
Automatic Tracking .....................................................28
Aux Input ....................................................................53
AV Compu Link Playback ........................................... 33
AV Connection .............................................................6
B
Band ...........................................................................12
C
Cable Box ...................................................................15
Cable Box Brand Setting ..............................................17
Cable Box Controller ...................................................15
Cancel Program ..........................................................48
Cassette Adapter.................................... ...................... 25
Check Program ...........................................................48
Child Lock ..................................................................62
Connection to TV ..........................................................6
Contents ........................................................................5
Counter Memory .........................................................32
Counter Reset ..............................................................32
D
Delete Channel ...........................................................14
DSS Receiver ..............................................................22
Dual Quick Setting ........................................................7
E
Editing .........................................................................51
F
Frame-by-Frame Playback ........................................... 27
Function Setting ..........................................................29
G
Guide Channel Map ....................................................21
Guide Channel Setting ................................................20
H
I
Host Channel Selection ...............................................10
Illumi Guide ................................................................44
Index Search ...............................................................31
Insert Cassette .............................................................25
Instant ReView ............................................................32
ITR (Instant Timer Recording) ...................................... 50
J
Jog Dial .......................................................................27
L
Language Selection .......................................................8
M
Main Menu ...................................................................8
Manual Channel Setting ..............................................14
Manual Clock Setting .................................................. 11
Manual Tracking .........................................................28
MBR (Multi-Brand Remote) Code Setting ..................... 60
N
Next-Function Memory ...............................................33
O
On-Screen Display ......................................................30
On-Screen Timer Programming ................................... 46
On-Screen Timer Recording ........................................46
Override Auto Clock Setting ..........................................9
P
PBS Channel .................................................................7
Playback .....................................................................25
R
Record Safety Tab .......................................................26
Recording ...................................................................26
Repeat Playback ..........................................................31
Reverse Motion Playback ............................................35
Reverse Slow Motion Playback ................................... 27
RF Connection ..............................................................6
S
SAP (Second Audio Program) ...................................... 42
Second Audio .............................................................42
Select Cable Box Output Channel ............................... 16
Semi-Auto Clock Setting ..............................................10
Skip Search .................................................................36
Slow Motion Playback ................................................27
Specifications ..............................................................70
Still Picture Playback ...................................................27
Superimpose ...............................................................30
T
Tape Position Indicator ................................................33
Tape Speed Setting ......................................................26
TimeScan ....................................................................35
TIME SCAN SHUTTLE Ring .........................................35
Time Zone Selection ...................................................10
Tuner Setting ...............................................................12
V
Variable-Speed Search ................................................35
VCR Plus+ ...................................................................19
VCR Plus+ Timer Programming ................................... 44
VCR Plus+ Timer Recording ........................................44
68
FRONT VIEW
1 2 3 4 5 6 7 8 9
INDEX (cont.)
POWER
REC PAUSE A.DUB
INSERT
MARK
INDEX
ERASE SP/EP
MENU
HEAD PHONE VOLUME
•
•
•
•
•
•
•
•
•
•
•
VIDEO
R.A.EDIT
START
L–AUDIO–R
MONO
0 dB
L
–20 15 10 8 6 4 2 0 2 4 6 +8
I T R
VIDEO
M
TIMER
SP AM
EP
PM
H
dB
R
–20 15 10 8 6 4 2 0 2 4 6 +8
M S
ST
SAP
R E C
PLAY
PAUSE
CH
OK
! @ # $ % ^
PLAY
REW
SE
AR
CH
SLO
W
8
SLOW
SE
AR
C
H
FF
STOP/EJECT
REW FF
& * ( ) q w e
1 Power ON/OFF Button (
Z
pg. 8)
2 Menu Button (
Z
pg. 8)
3 INDEX MARK Button (
4 Record [REC] Button (
5 Pause Button (
Z
pg. 31)
Z
pg. 26)
Z
pg. 26)
6 INDEX ERASE Button (
Z
pg. 31)
7 Audio Dubbing [A. DUB] Button (
Z
pg. 55)
8 INSERT Button (
Z
pg. 56)
9 Recording Speed [SP/EP] Button (
Z
pg. 26)
0 Cassette Loading Slot
! Stop/Eject Button (
Z
pg. 25)
Z
pg. 25) @ Play Button (
# TIME SCAN Indicator (
Z
pg. 35)
$ TIME SCAN SHUTTLE Ring (
Z
pg. 25)
% TIME SCAN SHUTTLE Indicator (
Z
pg. 35)
* It is possible to listen to the audio using headphones.
Adjust the volume level using the Headphone Volume Control.
r t y u i o
^ JOG Dial (
Z
pg. 27)
& Headphone Jack*
* Headphone Volume Control*
( Video Input Connector (
Z
pg. 52)
) Mono Audio Input Connector (
Audio Input Connector [L] (
Z
pg. 52) q Audio Input Connector [R] ( w R.A. EDIT START Button ( e Instant REVIEW Button ( r Front Display Panel ( t Remote Control Sensor
Z
pg. 52)
Z
pg. 52)
Z
pg. 59)
Z
y Channel [CH]
5∞ Buttons ( u OK Button (
Z
pg. 8)
Z
i Rewind [REW] Button (
pg. 32)
pg. 69)
Z
o Fast-Forward [FF] Button (
Z
pg. 8)
pg. 25)
Z
pg. 25)
REAR VIEW
1 2
3 4
VIDEO
OUT
IN
L
AUDIO
R
(MONO)
PAUSE/
SPECIAL
FUNCTION
CABLE
BOX
ANT.IN
RF OUT
CH3
CH4
OFF
1 Power Cord (
Z
pg. 6)
2 Video Output Connector (
3 Video Input Connector (
4 ANT. IN Connector (
Z
Z
Z
pg. 6)
pg. 51)
pg. 6)
5 Audio Output Connector [L] (
6 Audio Output Connector [R] (
7 Audio Input Connector [R] (
Z
Z
pg. 6)
Z
pg. 6)
8 Mono Audio Input Connector (
pg. 51)
Z
pg. 51)
Audio Input Connector [L] (
Z
pg. 51)
5 6 7 8 9 0 !
@
9 PAUSE/SPECIAL FUNCTION connector
● Remote PAUSE Connector (
● AV COMPU LINK Connector (
● Random Assemble Editing Connector (
0 CABLE BOX Connector (
! RF Switch (
Z
pg. 6)
@ RF OUT Connector (
Z
Z
pg. 6)
Z
pg. 52)
Z
pg. 15)
pg. 33)
Z
pg. 58)
69
FRONT DISPLAY PANEL
1
2
3
4
5 dB
L
–20 15 10 8 6 4 2 0 2 4 6
+8
I T R TIMER
VIDEO
SP
AM
M EP
PM
H
dB
R
–20 15 10 8 6 4 2 0 2 4 6
+8
M S
ST
SAP
R E C
PLAY
PAUSE
%
$
#
1
2
0
!
@
6
7
8
9
#
3
4
5
6 7 8
1 Audio Level Meter (
Z
2 Timer Mode Indicator (
pg. 43)
Z
pg. 45)
3 Instant Timer Recording Indicator (
4 Video Mode Indicator (
Z
pg. 41)
Z
pg. 50)
5 “Cassette Loaded” Mark
6 Counter Memory Mark (
7 Tape Speed Indicators (
8 AM/PM Indicators (
Z
pg. 32)
Z
pg. 26)
9 Clock Display (
Z
pg. 7)
Z
pg. 7)
9
REMOTE CONTROL (Provided)
0 !
@
0 Channel Display [“AU” for AUX mode]
(
Z
pg. 7)
Counter Display (
Z
pg. 25)
! Child Lock Indicator (
Z
pg. 62)
@ Multi-Channel TV Sound Indicators (
# Pause Mode Indicator (
Z
pg. 42)
$ Play Mode Indicator (
Z
Z
pg. 26)
pg. 25)
% Recording Mode Indicator (
Z
pg. 26)
POWER
A B ENTER
1
4
7
C.RESET
CANCEL
CH SKIP
2
5
DAILY (M–F)
8
AUX
0
OSD
3
6
WEEKLY
9
TIMER
TV
VOL.
CH
SP/EP DISPLAY TV/VIDEO CABLE
TV VCR
PLAY
REW
FF
REC
C.M
EMOR
Y
ADD
MEN
U
STOP
PAUSE
SKIP SEAR
CH
OK
TIME
SCAN
ILLUMI GUIDE
MULTI BRAND
REMOTE CONTROL UNIT
&
*
(
) q w e r t y
$
%
^ u i
** If the remote control doesn't work properly, remove its batteries, wait a short time and then try again.
1 Instant REVIEW Button (
Z
pg. 32)
2 A/B Code Select Switch (
3 NUMBER Buttons (
Z
Z
pg. 62)
pg. 10)
4 “AUX” Mode Select Button (
5 CANCEL Button (
Z
pg. 51)
Z
pg. 48)
Counter [C.] RESET (
Z
pg. 32)
Channel [CH.] SKIP Button (
6 Volume [VOL] +/– Buttons (
7 DISPLAY Button (
Z
pg. 32)
Z
pg. 14)
Z
pg. 60)
8 Recording Speed [SP/EP] Button (
9 Rewind [REW] Button (
Z
pg. 25)
Z
pg. 26)
0 PLAY Button (
Z
pg. 25)
! Record [REC] Button (
Z
pg. 26)
@ Counter [C.] MEMORY Button (
ADD Button (
Z
pg. 14)
Z
pg. 8)
Z
pg. 32)
# MENU Button (
$ POWER ON/OFF Button (
Z
pg. 26)
Z
pg. 8)
% ENTER Button (
On-Screen Display [OSD] Button (
Z
pg. 30)
Z
pg. 45) ^ DAILY Timer Recording Button (
& WEEKLY Timer Recording Button (
Z
pg. 45)
Z
pg. 45)
* TIMER Button (
( Channel [CH]
5∞ Buttons (
) TV/VIDEO Button ( q TV/CABLE/VCR Switch (
Z
pg. 8)
Z
pg. 41) r STOP Button (
Z
Z
pg. 26)
pg. 25) t SKIP SEARCH Button (
Z
pg. 60) w Fast-Forward [FF] Button ( e PAUSE Button (
Z
pg. 25)
Z
pg. 36) y OK Button (
Z
pg. 8) u TIME SCAN Button (
Z
pg. 8) i ILLUMI GUIDE Button (
Z
pg. 44)
70
GENERAL
Power requirement
Power consumption
: AC 120 V` , 60 Hz
: 21 W
Temperature
Operating
Storage
Operating position
: 5°C to 40°C (41°F to 104°F)
: –20°C to 60°C (–4°F to140°F)
: Horizontal only
Dimensions (W x H x D) : 435 x 105 x 353 mm
Weight
Format
Maximum recording time
(15-3/16" x 4-3/16" x 13 -15/16")
: 5.5 kg (12.2 lbs)
: VHS NTSC standard
SP : 210 min. with ST-210 video cassette
EP : 630 min. with ST-210 video cassette
VIDEO/AUDIO
Signal system : NTSC-type color signal and
EIA monochrome signal, 525 lines/60 fields
Recording/
Playback system : DA-4 (Double Azimuth) head helical scan system
Signal-to-noise ratio : 45 dB
Horizontal resolution : 240 lines
Frequency range
Normal audio
Hi-Fi audio
Input/Output
: 70 Hz to 10,000 Hz
: 20 Hz to 20,000 Hz
: RCA connectors (IN x 2,
OUT x 1)
TUNER
Tuning system
Channel coverage
VHF
UHF
CATV
RF output
: Frequency-synthesized tuner
: Channels 2–13
: Channels 14–69
: 113 Channels
: Channel 3 or 4 (switchable; preset to Channel 3 when shipped) 75 ohms, unbalanced
SPECIFICATIONS
TIMER
Clock reference
Program capacity
: Quartz
: 1-year programmable timer/
8 programs
Memory backup time : Approx. 10 min.
ACCESSORIES
Provided accessories : RF cable (F-type),
Infrared remote control unit,
“AA” battery x 2,
Controller,
Audio/Video cable
Specifications shown are for SP mode unless otherwise specified.
E. & O.E. Design and specifications subject to change without notice.
FOR SERVICING
HOW TO LOCATE YOUR JVC SERVICE CENTER
71
TOLL FREE: 1-800-252-5722
Dear customer:
In order to receive the most satisfaction from your purchase, read the instruction booklet before operating the unit. In the event that repair is necessary, or for the address nearest your location, please refer to the factory service center list below or within the
Continental United States, call 1-800-252-5722 for your authorized servicer. Remember to retain your Bill of Sale for Warranty
Service.
— JVC
107 Little Falls Road
Fairfield, NJ 07004-2105
(201) 808-9279
5665 Corporate Avenue
Cypress, CA 90630-0024
(714) 229-8011
230 Eliot Street
Ashland, MA 01721-2377
(508) 881-5923
JVC SERVICE & ENGINEERING
COMPANY OF AMERICA
DIVISION OF US JVC CORP.
FACTORY SERVICE CENTER LOCATIONS
1500 Lakes Parkway
Lawrenceville, GA 30243-5357
(770) 339-2522
10700 Hammerly, Suite 110
Houston, TX 77043-2310
(713) 935-9331
14505 Commerce Way
Miami Lakes, FL 33016-1512
(305) 362-6252
705 Enterprise Street
Aurora, IL 60504-8149
(708) 851-7855
2969 Mapunapuna Place
Honolulu, HI 96819-2040
(808) 833-5828
890 Dubuque Avenue
South San Francisco, CA 94080-1804
(415) 871-2666
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production of the wide array of JVC products, service is the key to maintaining the high level performance for which JVC is world famous. The
JVC service and engineering organization stands behind our products.
NATIONAL HEADQUARTERS
JVC SERVICE & ENGINEERING COMPANY OF AMERICA
DIVISION OF US JVC CORP.
107 Little Falls Road
Fairfield, NJ 07004-2105
If you ship the product...
Pack your JVC unit in the original carton or one of equivalent size and strength. Enclose, with the unit, a letter stating the problem or symptom that exists and also a copy of the receipt or bill of sale you received when you purchased your JVC unit. Print your home return address on the outside and the inside of the carton. Send to the appropriate JVC Factory
Service Center as listed above.
ACCESSORIES
To purchase accessories for your JVC product, you may contact your local JVC Dealer.
Or from the 48 Continental United States call toll free:
1-800-882-2345.
Don't service it yourself.
CAUTION
To prevent electrical shock, do not open the cabinet. No user serviceable parts inside.
Refer servicing to qualified service personnel.
72
WARRANTY
LIMITED WARRANTY
CONSUMER VIDEO 1-90
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL
PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period as shown below. ("The Warranty Period")
PARTS LABOR
1
YR
90
DAYS
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN
COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and above which are covered on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service center, please call toll free: (800) 252-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service, or if affixed to any attachment not provided with the products, or if the model or serial number has been altered, tampered with, defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;
7. Accessories;
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase); from the date of purchase);
There are no other express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS
LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO
TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET
FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential dameges or limitations on how long an implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
JVC COMPANY OF AMERICA
DIVISION OF US JVC CORP.
41 Slater Drive
Elmwood Park, New Jersey 07407
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF
REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION
PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain this information for future reference.
Model No.:
Purchase date:
Serial No.:
Name of dealer:
MEMO
73
MEMO
JVC COMPANY OF AMERICA
DIVISION OF US JVC CORP.
41 Slater Drive, Elmwood Park, N.J. 07407
COPYRIGHT © 1996 VICTOR COMPANY OF JAPAN, LTD.
U/U(C)
Printed in Malaysia
0696HOV * UN * PJ
advertisement
Related manuals
advertisement
Table of contents
- 6 Basic Connections
- 7 Dual Quick Set
- 8 Language
- 9 Clock
- 9 Preparation
- 10 Semi-Auto
- 11 Manual
- 12 Tuner
- 12 Set Receivable Channels
- 14 Add Or Delete A Channel
- 15 Cable Box Control
- 15 Situate And Connect Controller
- 16 Set Cable Box Output Channel
- 17 Set Cable Box Brand
- 19 VCR Plus+ Setup
- 22 DSS Receiver Control
- 22 Situate And Connect Controller
- 23 Set DSS Receiver Output Channel
- 24 Set DSS Receiver Brand
- 25 Simple Playback
- 26 Simple Recording
- 27 Playback
- 27 Still Picture/Frame-By-Frame Playback
- 27 Slow Motion/Reverse Slow Motion
- 28 Manual Tracking
- 29 Select The Soundtrack
- 30 Superimpose
- 31 Index Search
- 31 Manual Index Mark/Erase
- 31 Repeat Playback
- 32 Instant ReView
- 32 Counter Reset
- 32 Counter Memory
- 33 Tape Position Indicator
- 33 Next-Function Memory
- 33 AV COMPU LINK Playback
- 35 Time Scan
- 35 High-Speed Search (7 x playback)
- 35 Variable-Speed Search/Reverse Play
- 36 Skip Search
- 37 Time Scan Audio
- 38 Active Video Calibration
- 38 Preparation
- 39 Recording
- 40 Playback
- 41 Recording
- 41 Watching Another
- 41 Display Elapsed Recording Time
- 42 Stereo And SAP (Second Audio Program)
- 42 To Record SAP Programs
- 43 Hi-Fi Audio Recording Level Control
- 44 VCR Plus+ Timer Programming
- 46 On-Screen Timer Programming
- 48 Check And Cancel Programs
- 49 Auto Timer
- 50 Instant Timer Recording (ITR)
- 51 Edit To Or From Another VCR
- 52 Edit From A Camcorder
- 54 Assemble Editing
- 55 Audio Dubbing
- 56 Insert Editing
- 58 Random Assemble Editing
- 60 TV Multi-Brand Remote Control
- 61 Cable Box Multi-Brand Remote Control
- 62 Control Two JVC VCRs
- 62 Child Lock
- 63 Power
- 63 Tape Transport
- 63 Playback
- 64 Recording
- 64 Timer Recording
- 65 Other Problems
- 66 Playback
- 66 Recording
- 66 Timer Recording
- 67 List Of Terms
- 68 Front View
- 68 Rear View
- 69 Front Display Panel
- 69 Remote Control