SAMSUNG P1401, P1201, P1001, P801 washing machine SERVICE Manual
Annonce
Annonce
WASHING MACHINE
P1401
P1201
P1001
P801
SERVICE
Manual
WASHING MACHINE CONTENTS
Caution for the safety during servicing
1. SPECIFICATIONS
2. OVERVIEW OF THE WASHING MACHINE
3. OVERVIEW OF THE CONTROL PANEL
4. GENERAL ERROR FUNCTION
5. TROUBLE DIAGNOSIS
6. TEST MODE
7. DESIGNATION OF MAIN COMPONENTS
8. PCB SCHEMATIC DIAGRAM
PCB CIRCUIT DIAGRAM
9.ASSEMBLE AND DISASSEMBLE
10.
TOOLS FOR DISASSEMBLY AND ASSEMBLY
11.EXPLODED VIEW AND PARTS LIST
2
Caution for the safety during servicing
1. Do not allow the customer to repair the product.
☞
The person may be injured or the product life may be shortened.
2. Execute A/S after unplugging the power supply unit.
☞
Be care of the electric shock.
3. Do not plug several plugs in the same outlet.
☞
It may cause the fire due to overheat.
4. Check the damage, pressing or burning of the power plug or outlet.
☞
Replace it promptly if it has problem.(It may cause the electric shock or fire)
5. Do not clean the main body with the water.
☞
It may cause the electric shock and fire and shorten the product life)
6. The wiring of the harness shall be free from the moisture and tightened during serving.
☞
It shall not be deviated by certain impact.
7. Remove any dust or filth on the housing section,wiring section,connection section during servicing.
☞
Protect the cause of the fire such as the tracking,shortage and etc.
8. Check any mark of the moisture on the electrical parts, harness section and etc.
☞
Replace the parts or remove the moisture.
9. Check the assembly status of the parts after servicing.
☞
Maintain the status before servicing.
10. Pull out the power cord with holding the plug.
☞
Be care of the electric shock and fire when the cord is damaged.
11. Unplug the power plug from the outlet when the wash machine is not used.
☞
Be care of the electric shock and fire due to the strike of the lightening.
12. Do not use or store the spray or flammable materials(including gasoline,alcohol and etc.) around the wash machine.
☞
Be care of the explosion or fire due to the electric spark.
13. Do not put the bowl of water or wet laundry on the wash machine.
☞
If the water is penetrated to the wash machine, this may cause the electric shock or fire.
14. Do not install the wash machine in the place where the snow or rain falls.
☞
It may cause the electric shock and fire and shorten the product life.
15. Do not push the control buttons with the awl,pin, or sharp materials.
☞
It may the electric shock and trouble.
16. Check the wash machine is leveled horizontally and installed properly on the floor.
☞
The vibration may shorten the product life.
17. Joint the wire by the connector correctly.
☞
When the wire is jointed by the tape, this may cause the fire due to the tracking.
18. When the wash machine is to be laid for the service, put the pad on the floor and lay the product at side slowly.
☞
If the wash machine is laid front, the relay may be damaged by the tub.
19. When the wash-heater is replaced, check it is inserted in the bracket-heater and screw the nut.
☞
If the wash-heater is not inserted in the bracket-heater properly, this may cause the noise and leakage since it is contacted to the drum.
SAMSUNG ELECTRONICS CO., LTD
1. Specifications
WASH TYPE
DIMENSION
WATER PRESSURE
WEIGHT
WASH and SPIN CAPACITY
POWER CONSUMPTION
WATER CONSUMPTION
SPIN REVOLUTION
GROSS
NET
GROSS
NET
WASHING
WASHING and
HEATING
SPIN
MODEL
220-240V
PUMPING
MODEL rpm
FRONT LOADING TYPE
W 680mm X D 665mm X H 892mm
W 598mm X D 550mm X H 844mm
50 kPa ~ 800 kPa
80 kg
75 kg
5.5 kg (DRY LAUNDRY)
220 V 180 W
240 V
220 V
240 V
P1401 P1201
550W 500W
180 W
2000
2400
P1001
500W
34 W
49
l
(STANDARD COURSE)
P1401
1400
P1201
1200
P1001
1000
P801
430W
P801
800
SAMSUNG ELECTRONICS CO., LTD 3
2. Overview of the Washing Machine
4 SAMSUNG ELECTRONICS CO., LTD
3. Overview of the control panel
P1401/P1201
P1001
P801
8 9
1. Detergent dispenser
2. Display panel
Displays the remaining wash cycle time and error messages.
3. Program button
Press the button to select one of the eight available wash programs.
Cotton, Colour, Synthetic, Delicate, Wool, Quick, Rinse+Spin, Spin
4. Option Button
Press the button repeatedly to cycle through the available partial wash options
P1401/P1201 : Eco +
➔
Rinse +
➔
Prewash
➔
(Eco + +Rinse + )
➔
(Rinse + +Prewash)
➔
Cancel
➔
Eco +
P1001/P801 : Rinse +
➔
Prewash
➔
(Rinse + +Prewash)
➔
Cancel
Note : Prewash is available only with Cotton, Colour, Synthetic or Delicate programs.
5. Spin selection button
Press the button repeatedly to cycle through the available spin speed options.
P1401
P1201
P1001
P801
no, rh, 400, 600, 800, 1000, 1200, 1400 rpm no, rh, 400, 600, 800, 1000, 1200 rpm no, rh, 400, 600, 800, 1000 rpm no, rh, 400, 600, 800 rpm
no:no spin, rh:rinse hold
When pressing this button during operation, you can see the selected spin speed in the display panel.
6. Temperature selection button
Press the button repeatedly to cycle through the available water temperature options (cold water, 30 ˚C, 40 ˚C , 60 ˚C and 95 ˚C).
When pressing this button during washing, you can see the selected temperature in the display panel.
7. Delay Start button
Press the button repeatedly to cycle through the available delayed start options
(from 1 hour to 24 hours in one hour increments).
8. Start/Pause button
Press to pause and restart programs.
Press once to turn the washing machine on, press again to turn the washing machine off. If the washing machine power is left on for longer than 10 minutes without any buttons being touched, the power automatically turns off.
SAMSUNG ELECTRONICS CO., LTD 5
7. Designation of Main Components
7-1 Normal / Reverse Revolution of Motor and R. P. M. Control
1 2 3 4 5 6 7 8 9 10
8
5
Rotor
Stator coil
9
+
10
-
CW
8
Rotor
Stator coil
9
+
5
-
10
CCW
STATOR
5
<Figure1>
WASHING MOTOR
<Figure2>
H
( ± 7%)
Resistance value
STATOR(5.10) STATOR(5.1) ROTOR(8.9) TACHO(3.4) PROTECTOR(6.7) “H”(mm) Code-No
2.07
Ω
0.90
Ω
2.35
Ω
42.7
Ω
0 45 DC31-00002C
Rated value 220~240V / 50Hz
Remark
B
7-2 Door safety Device
DC61-00122A
7-3 Heater
1) Capacity : AC 230V/2000W
2) Location : Bottom of TUB
3) Function : Raise the water temperature supplied at the wash process.
4) Resistance value : 23
Ω
~ 29
Ω
5) Thermal Fuse : 128°C
10
Thermistor
SAMSUNG ELECTRONICS CO., LTD
7-4 ASSY-TUB BACK
OUT-BEARING
B
INNER-BEARING
A C
OIL-SEAL
TYPE INNER-BEARING(A) OUT-BEARING(B) OIL-SEAL(C) Assy-Housing Bearing(D)
I
II
III
ø 30
ø 30
ø 20
ø 25
ø 25
ø 17
ø 43.9
ø 43.9
ø 24.3
DC97-00419A
DC97-00125A
DC97-00215D
Assy-Tub Back
(unit : mm)
REMARK
DC97-00214A P1401
DC97-00214B P1001/P1201
DC97-00214K P801
7-5 ASSY- DRUM
C
A
B
TYPE
I
(A)
ø 30
(B)
ø 25
II
III
IV
ø 30
ø 30
ø 20
SAMSUNG ELECTRONICS CO., LTD
ø 25
ø 25
ø 17
(C)
ø 44.7
ø 44.7
ø 44.7
ø 25
CODE-NO.
DC97-01463A
DC91-12281A
DC97-00785B
DC97-00785A
REMARK
Lifter type
P1001/P1201/P1401
P1001/P1201
P1401
P801
(unit : mm)
11
6
4. General Error Function
•· When an error occurs, this function starts to keep generating error melody sounds and displays error indicators as shown in the followings per corresponding error by blinking in 0.5sec interval until the error status is completely cleared out. In this case, all the driving devices are turned off until the error is cleared out.
1. WATER SUPPLY ERROR
- Display shows ‘E1’.
- Water Supply Error occurs when water level frequency does not show changes more than 100Hz or water is not supplied up to the water level presetting for 20 min or more at the time of initial water supply.
- The error status can be cleared by turning POWER S/W OFF and resuming the POWER ON initial status.
2. WATER DRAIN ERROR
- Display shows ‘E2’.
- In case the water level frequency is 25.5KHz or less in the initial phase of UNB-detecting cycle.
- Water Drain error can be cleared by turning POWER S/W OFF and resuming the POWER ON initial status.
3. OVER-FLOW ERROR
- Display shows ‘E3’.
- Over-Flow error occurs when the water level is in abnormal operation. It can be cleared by turning POWER S/W
OFF. Water is drained prior to POWER S/W OFF and it is forced to be drained for 2 min if a frequency of more than 25.24 KHz is detected.
4. DOOR OPEN ERROR
- Display shows ‘door’
- Door Open error can be cleared by closing the door.
5. UNBALANCE ERROR
- Display shows ‘E4’.
- Laundry load is unbalanced; loosen any tangled laundry.
- If only one item of clothing needs washing, such as a bathrobe or jeans, the final spin result might be unsatisfactory and an “E4” error message will be shown in the display window.
- Unbalance error is cleared by POWER S/W OFF and by resuming the POWER ON initial status.
6. WATER HEATER ERROR
- Display shows ‘E5,E6’.
- In case the water temperature rises by 40°C or more in 5 min. or by 2°C less in 10 min after heating is started.
- It can be cleared by turning POWER S/W OFF.
7. ASS’Y PRESSURE S/W ERROR
* Generated Frequency Signal of WATER LEVEL(W/L) S/W (KHz)
Level
Abnormal W/L Frequency
Low Level High Level
30.00 KHz 15.00 KHz
- If the same signal as the above table is detected for more than 5 seconds, it is a PRESSURE S/W Error.
- When the error occurs, water drain pump will operate for 3 min. and then turn off the water drain pump.
Then the display shows ‘E7’ indicating a pressure s/w error indicator.
8. ABNORMAL WATER TEMPERATURE ERROR
Course
Delicate
Wool
Water Temp
50˚C or more
50˚C or more
- In case the water temperature is 50°C or more in Delicate and Wool course.
- At the time of initial water supply, if the water temperature is not appropriate, water starts to be drained and it is forced to be drained for 2 min when the abnormal frequency of 25.24KHz is detected.
- Display shows ‘E8’.
- This error can be cleared by POWER S/W OFF.
9. WATER LEAKAGE ERROR (E9)
- Water Leakage error occures when water is drained naturally after washing program starts.
SAMSUNG ELECTRONICS CO., LTD
5. Trouble Diagnosis
●
As the micom wash machine is configured of the complicate structure, there might be the service call.
Below information is prepared for exact trouble diagnosis and suitable repair guide.
Caution for the Repair and Replacement
Please follow below instruction for the trouble diagnosis and parts replacement.
1) As some electronic components are damaged by the charged static electricity from the resin part of wash machine or the human body, prepare the human body earth or remove the potential difference of the human body and wash machine by contacting the power supply plug when the work contacting to PCB is executed.
POWER SUPPLY PLUG
2) Since AC220~240V is applied to the triac T1 and T2 on P.C.B, the electric shock may occur by touching and be careful that the strong and weak electricity are mixed.
3) As the P.C.B assembly is designed for no trouble, do not replace the P.C.B assembly by the wrong diagnosis and follow the procedure of the trouble diagnosis when the micom is not operated normally.
SAMSUNG ELECTRONICS CO., LTD 7
8
5-1. Trouble Diagnosis
No
1
Item
The power is not supplied
Cause and treatment
- Is the PCB connector connected well?
- Is the voltage normal?
- Is the power supply plug connected well?
- Is the noise filter connected well?
- Is the secondary output of the power supply transformation normal?
- Is the fuse disconnected? (option)
• If above points are not found, the PCB assembly is out of order.
Replace it.
2
3
4
5
6
7
8
9
The water is not supplied.
The wash does not start though the water supply is stopped.
- Is the knob open?
- Did you push START/PAUSE button after selecting the course?
- Is the water supply valve connected well?
- Is the winding of the water supply valve continuous?
- Is the connection and operation of the pressure switch normal?
• If above points are not found, the PCB assembly is out of order.
Replace it.
- Is the connection and operation of the pressure switch normal?
- Is the pressure switch hose damaged so that the air is leaked?
- Is the pressure switch hose bent?
- Check the operation of the water level switch.
• If above points are not found, the PCB assembly is out of order.
Replace it.
The drum does not rotate during washing.
- Is the belt connected well?
- Is the winding of the motor continuous?
(Rotor winding, stator winding, generator)
- Is the motor protector normal?
• If above points are not found, the PCB assembly is out of order.
Replace it.
The drum rotates by one direction - The PCB assembly is out of order. Replace it.
during washing. (The drum rotates (Inversion relay open trouble) to one direction for SPIN.)
Drainage problem.
Dehydration problem.
Abnormal noise during SPIN.
Leak breaker or current/leak breaker is down during washing.
- Is the drainage hose bent?
- Is the winding of the drainage pump continuous?
- Is the drain filter clogged by the waste?
• If above points are not found, the PCB assembly is out of order.
Replace it.
- The unbalance is detected.
- Put in the laundry uniformly and start again.
- Is the pulley nut loosen?
- Is the transport safety device removed?
- Is the product installed on the level and stable place?
(Little noise may be generated during the high-speed SPIN.)
<When the leak breaker and current breaker is installed separately>
- When the leak breaker is down, check and make the earth of the outlet.
- When the current is down, the current is leaked.
<Is the breaker down when the leak/current breaker is combined?>
- Check the rated capacity of the current and leak breaker.
The current breaker may be down due to the lack of the current when the wash machine and other apparatus are used.
In this case, execute the cold water wash to check whether the current capacity is lack.
10 The heating is not executed.
- Is the wash heater terminal unplugged?
- Is the wash heater normal?
- If above points are not found, the PCB assembly is out of order.
Replace it.
SAMSUNG ELECTRONICS CO., LTD
6. Test Mode
1. Driving Compartment Test Mode
A. Hold down “1” and “2” keys simultaneously and then press POWER S/W “4” on.
(Whole lamps turn on and display show “tl” after 3 Seconds.)
B. The driving compartment can be tested when you press “3” key right after entering into the initial stage of the TEST MODE.
• Driving Compartment Test
Pre-wash VALVE ON(0.3sec)
➔
OFF(0.3sec)
➔
COLD VALVE ON(0.3sec)
➔
[OFF(0.3sec)
➔
HOT VALVE ON (0.3sec) :
OPTION
]
➔
OFF(0.3sec)
➔
Rinse VALVE ON(0.3sec)
➔
OFF(0.3sec)
➔
Pump MOTOR ON(0.3sec)
➔
OFF(0.3sec)
➔
MOTOR Left (0.5sec)
➔
OFF(0.5 sec)
➔
MOTOR Right (0.5sec)
➔
OFF(0.3sec)
➔
HEATER RELAY ON(0.3sec)
➔
OFF(0.3sec)
➔
DOOR OPEN
(Function continues when door is closed)
2. THERMISTOR TEST MODE
A. Hold down “1” and “2” keys simultaneously and then press POWER S/W “4” on.
(Whole lamps turn on and display show “tl” after 3 Seconds.)
B. Press the “1” key and display shows “t2”
C. Press the “3” key and display shows the inside temperature of tub.
SAMSUNG ELECTRONICS CO., LTD 9
5. Main function
9) Power-out compensation function
● If power is out on selected process, the process before power out is stored to EEPROM, once power is back the process before power out continues.
● When power is back, washing process starts from the process at the point of the power out, rinse/drain process starts from the initial process.
POWER-OUT COMPENSATION FUNCTION PROCESS
START WASHING
RINSE/DRAIN
START
FINISH
POWER OUT
SAVE DATA to EEPROM
POWER BACK
READ DATA
(PROCESS+TIME)
MICOM RESTORE
RESTART
PROCESS
SAVE DATA to EEPROM
RINSE/DRAIN
PROCESS
POWER OUT
POWER BACK
MICOM RESTORE
10) Water heater Error function
① This function starts working, when the heater works abnormally.
(this function begins sensing the heater 2 minutes later, after the heater operating)
② The value of the initial thermistor(A1) is compared with that of the thermistor(A2) in 2 minutes (Y=A2-A1)
- For 10 minute the variance of temperature(Y) is less than 2℃ "E5"message is displayed on the panel.
③ The value of the initial thermistor(A1) is compared with that of the thermistor(A2) in 11 minutes (Y=A2-A1)
- For 1 minute the variance of temperature(Y) increases more than 7℃(0.3V) "E6"message is displayed on the panel.
④ At this time heater, Error "E5 (heater do not work), E6(overheated)" is displayed and all working process off
⑤ The heater operating continues during heating hours, if washing hour is left over, the residual washing process keeps going without heating.
8
6. Test Mode
1. Driving Compartment Test Mode
A. Hold down “1” and “2” keys simultaneously and then press POWER S/W “4” on.
(Whole lamps turn on and display show “tl” after 3 Seconds.)
B. The driving compartment can be tested when you press “3” key right after entering into the initial stage of the TEST MODE.
• Driving Compartment Test
Pre-wash VALVE ON(0.3sec)
➔
OFF(0.3sec)
➔
COLD VALVE ON(0.3sec)
➔
[OFF(0.3sec)
➔
HOT VALVE ON (0.3sec) :
OPTION
]
➔
OFF(0.3sec)
➔
Rinse VALVE ON(0.3sec)
➔
OFF(0.3sec)
➔
Pump MOTOR ON(0.3sec)
➔
OFF(0.3sec)
➔
MOTOR Left (0.5sec)
➔
OFF(0.5 sec)
➔
MOTOR Right (0.5sec)
➔
OFF(0.3sec)
➔
HEATER RELAY ON(0.3sec)
➔
OFF(0.3sec)
➔
DOOR OPEN
(Function continues when door is closed)
2. THERMISTOR TEST MODE
A. Hold down “1” and “2” keys simultaneously and then press POWER S/W “4” on.
(Whole lamps turn on and display show “tl” after 3 Seconds.)
B. Press the “1” key and display shows “t2”
C. Press the “3” key and display shows the inside temperature of tub.
SAMSUNG ELECTRONICS CO., LTD 9
8. PCB Schematic Diagram
12 SAMSUNG ELECTRONICS CO., LTD
8. PCB CIRCUIT DIAGRAM
SAMSUNG ELECTRONICS CO., LTD
8-1. WB : ASSY-PCB Part List
NO. Part Code Code No. Q'ty Description
WB003
WB006
WB006
WB006
WB006
WB007
WB008
WB007
WB002
WB002
WB003
WB004
WB004
WB004
WB004
WA010
WB007
WB009
WB010
WB011
WB012
13
14
15
16
9
10
11
12
17
18
19
20
21
7
8
5
6
3
4
1
2
1401-001007
1401-001024
0402-001023
3501-001180
1 THYRISTOR-TRIAC
5 THYRISTOR-TRIAC
1 DIODE-BRIDGE
1 RELAY-MINIATURE
3501-001156
3501-001157
2 RELAY-POWER
3 RELAY-POWER
3501-001007 1 RELAY
DC26-00005B 1 TRANS-FORMER
0402-000137
0504-000130
6 DIODE-RECTIFIER
2 TR-DIGITAL
DE13-20016A 1 IC-VOLT REGU.
0504-000159 2 TR-DIGITAL
0501-000465
1202-000141
1 TR-SMALL
1 IC-VOL. COMP
2802-001058 1 RESONATOR-CERAMIC
DE13-20017A 3 IC-DRIVE
1103-001160 1 IC-EEPROM
DE30-20016A 1 BUZZER
3404-001022 7 SWITCH-TACT
DE07-20040A * LED LAMP
0703-001056 1 LED DISPLAY
Specificatio
10A,SM10LZ47(TOSHIBA)
2A,SM2LZ47(TOSHIBA)
RBV1506,600V,15A,SIP-4
12V DC,RTE24012
12VDC,0.53W,16000MA,1FORMA
12VDC,0.53W,16000MA,1FORMC
12Vdc,200mW,5A,(TAKAMISAYA)
450MA,220~240VAC,11VDC
1N4007,1000V,1A
KSR1105
KA7805A
KSR2105
MMBT390X
7033,SOT-89
8MHz,0.2%,TP,10x5x8mm
KID65003AP,DIP,16P,STICK
4C010,128X8BIT,DIP,8P
CBE2220BA,STICK
15V,20mA,130°
±
40gf,6x6x5mm
SLH-34VC70F,RED,T,PI5
Y-GRN,4dig,7seg,46X19X24.6mm
Remark
TRIAC1
TRIAC 2~6
BD1
RELAY3
RELAY 5
RELAY 1,2
RELAY6
TRANS
D15~D19
TR3,TR4
TR7
TR1,TR2
TR5,TR6
IC4
RESO
IC3,IC5,IC6
IC2
BZ
SW 1~7
SAMSUNG ELECTRONICS CO., LTD 13
9. Assemble and Disassemble
1. ASS’Y-COVER TOP
1) Remove two screws fixing the top-cover on back side.
2) Push the top-cover back about 15mm and pull it up.
3) It’s possible to exchange and service Assy-Panel
(PCB), the pressure-sensor, the noise-filter, the water valve and trans(option).
15mm
SCREW
2. FRAME FRONT
1) Remove the top-cover and the ass’y drawer.
2) Remove two screws fixing the control-panel on front side and the screw on right side.
3) Remove the cover-front(L) by using the (-)driver.
4) Pull the lever and open the ass’y-door.
5) Part the diaphragm and the wire diaphragm away from the frame-front.
6) Remove the eight screws fixing the frame-front.
7) It’s possible to exchange and service the heater, the pump, the shock-absorber and the door lock s/w.
LEVER
14 SAMSUNG ELECTRONICS CO., LTD
9. Assemble and Disassemble
3. BELT
1) Remove the top-cover.
2) Disassemble and assemble the belt.
3) Check the belt is located at center of the motor-pulley.
<When assemble the belt>
Hook the belt on the motor pulley 1) and place it around the pulley 2).
2
PULLEY
BELT
1
MOTOR
4. MOTOR
1) Lay down the washer on left side.
2) Remove the wire housing from the motor.
3) Remove the bolt fixing the motor with the box drive on back side.
4) Remove the motor.
Motor Assemble Hole
5. How to Assemble the RELAY Housing.
<CAUTION>
Insert the Relay Housing to the Relays on the opposite direation each other.
[Relay Housing Color]
A
WHITE
B
BLUE
Relay Housing (A)
Relay
Relay Housing (B)
SAMSUNG ELECTRONICS CO., LTD 15
10. Tools for Disassembly and Assembly
NO.
①
Box driver
TOOL
10mm
13mm
17mm
19mm
Heater (1)
Motor (1), Balance (5)
2 holes of each left and right of the shock absorber
1 Pulley hole
➁
Double-ended spanner
10, 13
17, 19mm
Replaceable for the box driver.
Since the bolt runs idle when the box driver is used, use the box driver 17mm.
➂
Vice pliers Tool to protect the idle and abrasion of the bolt for the box driver.
➃
Other(Driver, Nipper, Long nose) General tools for the after service.
➄
JIG for the Tub 1 (Disassemble and Assemble)
➃
①
➄ ➁ ➃ ➂
16 SAMSUNG ELECTRONICS CO., LTD
10. Designation of Main Components
10-1 Normal / Reverse Revolution of Motor and R. P. M. Control
1 2 3 4 5 6 7 8 9 10
8
5
Rotor
Stator coil
9
+
10
-
CW
8
Rotor
9
+
Stator coil
5
-
10
CCW
STATOR
5
<Figure1>
WASHING MOTOR
<Figure2>
H
(± 7%)
STATOR(51) ROTOR(8.9) TACHO(3.4) PROTECTOR(6.7) "H"(mm) Code-No.
Remark
Resistance value
Rated value
2.08Ω 1.99Ω 38.8Ω 0
220~240V/50Hz
39 DC31-00002E C1235
10-2 Door safety Device
1)Capacity
Code No : DC64-00652A
3P 1 - 2 Locking : 135Ω ±10%
2 - 3 UnLocking : 135Ω ±10%
4P 1 - 2 Door Lock 250V 16A
3 - 4 Door close 250V (16)1A
23
10-3 Heater
1) Capacity : AC 230V/1900W
2) Location : Bottom of TUB
3) Function : Raise the water temperature supplied at the wash process.
4) Resistance value : 23~29
5) Thermal Fuse : 169°C
Thermistor
10-4 Detergent tub and water supply value
A Detergent tub is composed of housing and 3 drawers . supplied water flows into the 3 drawer-detergent tub by way of classifier at each washing process.
three open drainage way whith detergent and supplied water by way of connector located under the housing flows into washing tub.
the water supply valve is composed of a hot water valve(1 way) and a cold water valve(2way) and water flow per min in the valve is below.
water flow(L/min) resistance value power consumption usable water pressure
Hot water valve(1 way)
10L
4.3㏀
AC 220v ~ 240V 50/60㎐
0.5 ~ 8 ㎏/㎤
10-5 Shock absorber and buffer spring
This wash machine is equipped with 2 Shock absorbers with same capacity and with 2 buffer springs. 2 Shock absorber are placed under the tub and outside case , 4 buffer springs are placed on the right and left of the upper side of outside case.
Shock absorber function: during wash, dehydration absorb the shock.
buffer spring: buffering the vibration device
Shock absorber capacity of Shock absorber
8±2kg
24
10-6 ASSY-TUB BACK
OUT-BEARING
B
INNER-BEARING
A C
OIL-SEAL
TYPE INNER-BEARING(A) OUT-BEARING(B)
I ø 30 ø 25
OIL-SEAL(C)
ø 34
10-7 ASSY- DRUM
Assy-Housing Bearing(D)
DC97-05168A
(unit : mm)
Assy-Tub Back
DC97-00214R
C
A
B
TYPE
I
(A)
ø 30
(B)
ø 23
10-8 ASSY-PUMP DRAIN
1) Capacity : AC 230V 34W
2) Location : Front bottom(R)
3) Resistance : 150Ω ~ 180Ω
(C)
ø 35
CODE-NO.
DC97-01463H
(unit : mm)
REMARK
25
11. WC:TOP(FRONT) - Exploded View
SAMSUNG ELECTRONICS CO., LTD 17
11-1. WC:TOP(FRONT) Parts List
8
9
WZ001
WCD04
10 WCD05
11 WZ001
12 WCD07
13 WCD08
14 WCD09
15 WCD10
16 WCD11
17 WZ008
18 WZ016
19 WCD12
No. Location No. Description
1
4
5
2
3
6
7
WCD01
WCD02
WCD03
WC005
WC001
WZ001
WB001
Code No. Q'ty P801
●
PANEL - DRAWER DC63-00030M 1
DC63-00030L 1
DC63-00030K 1
DC63-00030J 1
BODY-DRAWER
GUIDE-LIQUID
DC61-30348A 1
DC61-60498A 1
CAP-RINSE DC61-10687A 1
ASSY-PANEL CONTROL DC97-01328C 1
SCREW TAPPING
ASSY PCB PARTS
DC97-01328A 1
6002-000445 2
MF-P801-00 1
MF-P1001-00 1
MF-P1201-00 1
MF-P1401-00 1
SCREW TAPPING DC60-20049A 3
ASSY-FRAME PLATE(U) DC97-00417A 1
ASSY-HOUSING DRAWER DC91-12085A 1
SCREW TAPPING DC60-20049A 1
COVER-DOOR
DOOR-GLASS
DC61-00055A
DC61-00013A
1
1
HOLDER-GLASS
LEVER-DOOR
ASSY-HINGE
WASHER-PLAIN
NUT-FLANGE
ASSY-FRAME FRONT
DC61-00057A
DC66-00016A
DC97-00100A
DC60-60025C
DD60-50018A
DC97-00702A
1
1
1
2
2
1
-
●
●
●
●
●
-
-
-
●
●
●
●
●
●
●
●
●
●
●
●
-
-
-
●
P1201
-
-
●
-
●
●
●
●
●
●
-
●
●
●
●
●
●
●
●
-
●
●
●
-
-
●
P1401
●
●
●
-
-
-
●
-
●
●
●
●
●
●
●
●
●
●
●
●
●
●
-
-
-
●
P1001
-
●
●
-
●
●
●
●
●
●
●
●
●
●
●
●
-
-
●
-
●
-
-
●
●
●
18 SAMSUNG ELECTRONICS CO., LTD
12. WD : TUB - Exploded View
SAMSUNG ELECTRONICS CO., LTD 19
12-1. WD : ASSY-TUB - Parts List
29
30
31
32
25
26
27
28
21
22
23
24
17
18
19
20
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
No. Location No. Description
33
34
35
36
WDD01 ASSY-WIRE DIAPHRAGM DC91-12078A 1
WDD02 DOOR-DIAPHRAGM DC61-20219A 1
WDD03 ASSY-CLAMP DIAPHGRAM DC97-00850A 1
WDD04 BOLT-W.MOTOR
DC60-40138A 3
WZ008 WASHER-PLAIN
WZ009 WASHER-NYLON
WDD05 WEIGHT-BALANCER(L)
WZ010 BAND RING
DC60-60044B
DC60-60040A
DC66-60154A
DC65-60125A
6
3
1
1
WDD06 HOSE-DRAWER TUB
WZ011 BOLT-HEX
WZ012 BOLT-FLANGE
WD007 HOSE-AIR
WDD07 WEIGHT-BALANCER(U)
WD006 PULLEY
WZ014 WASHER-SPRING
WZ013 NUT-HEX
DC62-10305A
DC60-40140A
DC60-40132B
DC62-10303A
DC66-60153A
DC66-10176B
DC60-60049A
DC60-50148B
1
2
1
1
1
1
1
1
WD008 BELT-TRANSMISSION
WDD08 CUSHION-MOTOR
WDD09 MOTOR-DRUM
WZ013 BRACKET-NUT
WZ010 BAND RING
WDD10 HOSE-FILTER TUB
WZ015 CLAMP-HOSE
WDD11 PACKING-TRAP
WD009 CAP-TRAP
WDD12 HEATER
WDD13 TUB-FRONT
WDD14 BRACKET-NUT
WDD15 BRACKET-HEATER
WDD16 SPACER-HEATER
WDD17 VANE-CHECK
WDD18 ASSY-DRUM
DC66-10139B
DC61-00041A
DC31-00002C
DC61-00201A
DC65-60118F
DC62-10304A
DC61-60497A
DC62-40184A
DC61-10676A
DC47-00001A
DC61-30346A
DC61-40348B
DC61-40344A
DC61-60496A
DC62-20311A
DC97-00785A
1
1
1
1
1
1
1
1
1
1
1
5
1
2
1
1
WDD19
WDD20
WDD21
WDD20
PACKING-TUB
CLIP-TUB
ASSY-TUB BACK
CLIP-TUB
DC91-12281A 1
DC97-00785B 1
DC62-40183A 1
DC61-60499B 8
DC97-00214K 1
DC97-00214B 1
DC97-00214A 1
DC61-60520A 1
Code No. Q'ty P801
-
-
●
●
●
-
-
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
P1201
-
-
●
●
●
-
-
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
P1001
-
●
-
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
-
●
-
●
P1401
-
-
●
●
●
-
-
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
20 SAMSUNG ELECTRONICS CO., LTD
13. WE:CASE - Exploded View
29
3
4
1
2
8
10
9
7
25
28
24
26
27
23
22
6
5
11
13
12
14
16
17
20
18
19
*option
30
15
21
SAMSUNG ELECTRONICS CO., LTD 21
13-1. WE:ASSY CASE OUTER - Parts List
No. Location No. Description
1
2
3
4
5
6
7
8
9
WA006 ASSY-M.WIRE HARNESS DC96-00052B 1
WA007 ASSY-WIRE HARNESS(SUB) DC96-00053B 1
WCD12 ASSY-FRAME FRONT
WED05 GUIDE-LEVER
WAD01 DOOR-LOCK S/W
WCD04 ASSY-FRAME PLATE(U)
WED04 HOSE-PRESSURE
WA002 SENSOR PRESSURE
WZ015 CLAMP-HOSE
10 WED05 BRACKET-PRESSURE
11 WED06 COVER-FRONT(L)
12 WZ011 BOLT-HEX
13 WZ011 BOLT-HEX
14 WED07 DAMPER-SHOCK
15 WED08 CAP-DRAIN
16 WD108 HOSE-DRAIN
17 WA003 ASSY-PUMP DRAIN
18 WE005 ASSY-LEG
19 WED09 ASSY-PAINT FRAME
20 WZ010 BAND RING
21 WZ005 ASSY-HOSE DRAIN(O)
22 WA001 ASSY-POWER CORD
23 WAD02 FILTER-EMI
24 WED10 SPRING-HANGER
25 WED11 SLEEVE-PLUG
26 WA009 VALVE-WATER(COOL)
27 WZ015 CLAMP-HOSE
28 WED12 HOSE-DRAWER
29 WCD13 ASSY-COVER TOP
30 WZ007 HOSE WATER(C)
DC96-00053A 1
DC97-00702A 1
DC61-60142A
DC61-00122A 1
DC97-00417A 1
DC62-10311A 1
DC32-30006P
DC61-60359D 1
DC61-40345A 1
DC61-10672A 1
DC60-40144A
DC60-40141A 2
DC66-60149A 2
DC61-10673A 1
DC62-10302A
DC96-00115A 1
DC91-12292A 4
DC99-00060A 1
DC65-60125B
DC97-00139B 1
DC96-00146A 1
DC29-00003A 1
DC61-70216C
DC61-60180A 3
DC62-30313A 1
DC61-60063B 6
DC62-10068A
DC97-00851A 1
DC62-10289B
1
1
2
1
1
2
3
1
Code No. Q'ty P801
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
-
●
●
●
P1001
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
-
●
●
●
P1401
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
-
●
●
●
P1201
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
-
●
●
●
22 SAMSUNG ELECTRONICS CO., LTD
15. TOP(FRONT) - Exploded View
R0036
R0036
A0242
C0002
C0115
R0019
F0125
D0004
D0112
D0061
D0045
F0064
C0103
15. TUB - Exploded View
U0004
U0355
U0095
U0010
R0158
R0030
U0029
U0038
U0355
U0028
U0033
R0001
U0328
U0016
U0015
U0078
U0026
U0018
15. CASE - Exploded View
P0001
A0114
W0001
W0004
R0158
A0115
R0159
W0032
Y0040
R0027
I0041
W0002
A0025
I0022
C0058
F0027
A0132
A0006
U0133
U0133
I0046
J0013
B0070
I0040
I0040
I0040
I0041
I0043
I0046
I0047
F0045
F0064
F0065
F0125
I0022
I0030
J0013
J0019
C0058
C0103
C0115
D0004
D0045
D0046
D0061
D0109
D0112
F0027
A0115
A0132
A0242
A0243
A0328
A0358
A0362
B0070
C0002
SVC code
A0006
A0023
A0025
A0034
A0043
A0043
A0067
A0114 code
DC61-10672A
DC97-01160A
DC91-12102A
DC60-40146A
DC61-10688A
DC67-00208A
DC69-00646A
DC61-20235A
DC61-60180A
DC61-10673A
DC64-00144X
DC68-00904A
DC63-00030M
DC96-00171A
DC61-40081A
DC97-14289A
DC97-01328A
DC61-20205B
DC66-00016A
MFS-P801H-00
DC97-00100C
DC97-03423B
DC97-04752A
DC64-00920C
DC61-60519A
DC61-00055A
DC99-00524A
DC97-09928D
DC97-00702W
DC97-05134B
DC61-30344A
DC97-14291B
DC62-10278A
DC97-01298A
DC97-01298B
DC62-10311A
DC67-00205A
DC67-00244A
DC61-01136A
DC96-01336M
DC61-01674E description spec
COVER-FRONT(L) SWF-P12,PP(BJ-730),-,-,-,
ASSY COVER DRAWER P1092,BLEACH-CASE,PP,-
ASSY FIXER TUB -,SWF-P12,-,-,-,-
BOLT-SPANER
CAP-FIXER
-,CR,-,T2.5,OD36,-,-,-,-
SWF-P12,PP(TB53),-,-,-,WHT,-,
CAP-FIXER
CUSHION-CORNER
SHUTTER
SLEEVE-PLUG
CAP-DRAIN
INLAY-PANEL
MANUAL-BOOK
PANEL-DRAWER
ASSY WIRE EARTH
J1453GW/XEU,PP,1.5mm,-,-,NTR,-
Q1636GW/XEU,EPS,-,-,-,-,7
DANPLA,PP(BB110),WHT,
NYLON#6,SEW-720DR,-,-,NTR
SWF-P12,PP(TB53),-,-,-,WHT,-,
P801DWN/XAC,PC(T=0.5),-,-,-,
P805J/P803J/P801,SECA,ENG+FR
-,ABS(HG-0760),-,-,-,-,WHT,
P-PJT(DRUM),-,-,WIRE/UL1
HOLDER-WIRE
ASSY LEG
ASSY PANEL CON-
TROL
DOOR-LOCK S/W
LEVER-DOOR
ASSY PCB PARTS(M)
ASSY HINGE
DAWH-2NC,NYLON66,-,-,-,-,NTR
ALL MODEL,Φ39 NUT-HEX FLANGE,-,
P1401/P1201/P1001,-,-
-,-,-,-,-,P1092,-,-,BITRON
POM,-,-,-,-,NTR,DWM599W,DANBY
P801DWN
S1005J,OPEN ANGLE 180DEG,-,-,
ASSY HOLDER GLASS P1403J,-,CUSION-LID/AB
ASSY LEVER DOOR P-PJT,-,LEVER+SPRING,-,-
DOOR-GLASS
GUIDE-BAR
COVER-DOOR
ASSY PAINT FRAME
WF-J145NV1/XEN,HeatTreatment
SWF-P12,SHV-745CC1(SSEC),-,-,-
P6091,ABS,-,-,-,-,-,WHT,ROUND
CLON-PJT,B1445AV,-,-,-,
ASSY FILTER
ASSY FRAME FRONT
V7-PJT,L65/W55/H55,-,-
-,MID-PJT/T0.8,-,-,-,RO
ASSY FRAME PLATE(U) R-PJT,WF-R1053/XSC,-
FRAME-PLATE(U) SWF-P12,EGI,-,-,NTR,-,-,-
ASSY HOSE DRAIN(O) UG-KT/TROIKA/GERMANY,
HOSE-HANGER -,PP,-,-,-,-,NTR,JS20 RESIN
ASSY HOSE WATER
ASSY HOSE WATER
HOSE-PRESSURE
HOSE-AIR
HOSE-DRAIN
CLAMPER HOSE
ASSY PUMP DRAIN
CASE-PUMP
W751SC,-,COLD,1.5MT,-,-
W751SC,-,HOT,1.5MT,-,-
-,EPDM,ID13.5,-,-,-,BLK,SW
ALL-MODEL,EPDM,ID16,-,T1.7,-,BL
HOSE-DRAIN,EPDM,ID6,OD11,T2.5
F1235J,SK5,-,T1.0/ID14.8,WH
B1113JDW/XAC,-,ASKOLL/3H
WF7600SUV/XEO,PP,T2.5,W65,L94,
Q’ty SA/SNA
1
1
1
1
3
1
1
1
1
1
4
1
1
1
5
1
6
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SA
SA
SA
SA
SA
SA
SA
SA
SA
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SNA
SA
SA
SA
DC31-30008F
DC97-11090B
DC61-10687B
DC97-01463E
DC66-10179B
DC66-10178A
DC97-13901A
DC97-06572P
DC91-12085A
DC97-00731A
DC91-12078A
DC61-30348A
DD60-50018A
6011-001492
DC67-00285A
DC67-00051D
DC61-70216C
DC61-70217C
DC60-60044B
DC60-60044A
DC63-10003C
DC60-60040A
DC66-10176B
DC97-00214L
DC31-00002D
DC62-00007A
DC63-00845A
DC61-40348B
DC61-00201A
DC97-00215C
DC61-10676A
DC61-20219A
DC62-10304A
DC91-12077D
DC97-10977B
6602-001497
DC66-00343G
DC61-00041A
DC60-40144A
DC60-40141A
DC62-40183A
R0030
U0003
U0003
U0004
U0005
U0010
U0013
U0015
R0036
R0106
R0147
R0158
R0158
R0159
R0159
U0078
U0095
U0133
U0307
U0320
U0320
U0328
U0016
U0018
U0023
U0023
U0026
U0028
U0029
U0033
U0038
J0025
P0001
P0036
R0001
R0002
R0005
R0017
R0019
R0019
R0027
PUMP-DRAIN
ASSY COVER TOP
CAP-RINSE
ASSY DRUM
DRUM-FRONT
DRUM-BACK
ASSY DRUM LIFTER
ASSY HOUSING
DRAWER
ASSY HOUSING
DRAWER
ASSY SENSOR PRES-
SURE
ASSY WIRE DIA-
PHRAGM
BODY-DRAWER
NUT-FLANGE
BOLT-FLANGE
HOSE-DRAWER TUB
HOSE-DRAWER
SPRING-HANGER
SPRING-HANGER
WASHER-PLAIN
WASHER-PLAIN
SPONGE-HOSE AIR
FASTENER-WASHER
PULLEY
ASSY TUB BACK
MOTOR UNIVERSAL-
DRUM
SEAL-OIL
COVER-HEATER
BRACKET-NUT
BRACKET-NUT
ASSY TUB FRONT
CAP-TRAP
DOOR-DIAPHRAGM
HOSE-FILTER TUB
ASSY CLAMP DIAPH-
GRAM
SW-70XP,120V,60Hz,SYNCHRONOUS
P1053GW/XEH,6.0KG/HUNGARY
SEW-HW108,ABS,-,-,-,GRN,-
P801(800RPM)KRNJM,LEFTER TYPE/
SB-PJT,STS430,-,-,-,-,T0.4
SWF-P12,STS430,-,-,-,-,T0.5
B MODEL,SSEC/B MODEL,-,
B/P2/H+C,VALVE/110V/
SWF-P12,-,-,-,-,-
P1091,S-PRE+BRAKET+
SWF-P12,FRAME-FRONT,
TS2-PJT,PP,T2.5,-,L262.9,W15
-,M5XP0.8,FZY,MSWR10,-
M8,L25,PASS,STS304,NYLOCK,P1
JUMP2-MODEL,EPDM,40,56,T
S1093~S6093,EPDM,-,-,-,-,BLK
P1291,HSWR,CD3.5,-,-,L175,
P1291,HSWR,CD3.2,-,-,L175,
-,SBC,ID8.4/OD30,T2.0,-,-,-
-,ID10.5,OD30,T3,-,STS304
POL,GRY,SWF-P12,HB22-GRE
-,ID10.5,OD32,T2,-,PBSP-
P1291,-,-,-,-,-,-,ID12.5
P801DWN/XAC,BACK/LOW-RPM,-
MCC61/64 148/SEC1,0
-,NBR(SD25),BLK,-,-,-,P6091/NBU
ALL MODEL,ABS(V0),-,-,-,-,-
SBHG-R,P1291,T3,-,-,-,NO-PAI
SBHG-R,P1291,T3,-,-,-,NO-PAI
P1003J/W1092F/UL,NO-HEAT/
SWF-P12,PP(TB53),-,-,-,-,-,
EPDM,-,-,-,-,-,-,GRY,SWF-
-,EPDM,ID65,-,-,L151,BLK
WF-B853/XSC,TUB,-,S
ASSY SEMI TUB BACK P801/5.5KG,-,-,RPP(GR
BELT-TIMING GEAR -,RUBBER(GATES),T3.4,-,
DAMPER-SHOCK
CUSHION-MOTOR
GW-PJT,STEEL+PP+RUBBER,100N
SWF-6V,BUTYL,-,-,-,ID16/OD
BOLT-HEX
BOLT-HEX
PACKING-TUB
M10,L41,ZPC2(YEL),SM10C/DAMPER
SM10C/DAMPER,HEX,M8,L66,-,ZPC2(
SWF-P12,EPDM,-,-,-,-,-,BLK,-
1
1
1
1
1
1
1
1
3
1
1 SA
1
5
5
2
1
1
1
3
1
1
2
0.97
SA
1
2
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
2
2
1
1
1
2
1
1
1
1
2
1
1
1
1
1
SNA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SC
SA
SA
SA
SA
SA
SA
SA
SA
SA
39
U0353
U0353
U0353
U0353
U0355
U0355
U0360
U0360
V0005
W0001
W0002
W0004
W0031
W0031
W0032
W0032
Y0040
Z0004
DC61-60359E
DC61-60497A
DC65-00019A
DC61-00133A
DC66-60153A
DC66-60154A
DC61-60499B
DC61-60520A
DC68-02315A
DC96-00174B
DC96-00038E
DC96-00173C
DC65-60118P
DC65-60118K
DC62-30309J
DC62-30310R
DC29-00009A
DC60-50148B
DC61-60142A
CLAMPER HOSE F1235AS/F1035AS,SK5,-,ID7.8
CLAMPER HOSE-JOINT SWF-P12,HSWR,-,ID70/O
CLAMPER HOSE
CLAMPER HOSE-FIX
DRUM W/M,SK5,-,D34/H5/T1.5,
P1291,PP,ID24.5,OD29.5,
WEIGHT-BALANCER
WEIGHT-BALANCER
CLIP-TUB
CLIP-TUB
SWF-P12,CONCRETE,UPPER,
SWF-P12,CONCRETE,LOWER,
HSWR,P1291,-,NO/PAINT,
SK5,SWF-P12,-,PLATE-TYPE,
LABEL-ENERGY P1005J~P801,-,MOJO+REMOV,-,
ASSY WIRE HARNESS -,P801(MIJU),-,SUB,-,-
ASSY POWER CORD
ASSY M. WIRE HAR-
NESS
BAND-RING
P1092,125V/13A/EP3,-,-
P10O3J(MIJU),-,-,NO
BAND-RING
VALVE-WATER
WF-F105AV,HSWR,T3.0,-,-,YEL,ID
HSWR,YEL,PI2.0,OD22,ID18
P1092,PP(J320),-,-,-,#187(11
VALVE-WATER
FILTER-EMI
NUT-HEX
GUIDE-LEVER
P1092,PP(J320),-,-,-,#187(11
DFC-2715R,P/PV/P2,250V,15A,PI
SM20C(NYLON),M12,-,-,ZPC3(YEL),-
-,Y745STC(S7A77),-,-,-,WHT,-
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
SA
1
1
8
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
40
ELECTRONICS
© Samsung Electronics Co., Ltd. May 2000
Printed in Korea
Code No. : DC68 - 00799A
Download
Offentligt link opdateret
Det offentlige link til din chat er blevet opdateret. You may view and manage your chat links after registration here.
Dokument offentligt link
Annonce
