IDEAL 4810-95, 4850-95, 4850-95EP, 5221-95EP, 6550-95EP Guillotines User Manual

Guillotines
GB Operating Instructions
IDEAL 4810-95
IDEAL 4850-95
IDEAL 4850-95EP
IDEAL 5221-95EP
IDEAL 6550-95EP
• Safety precautions •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
D
GB
F
NL
I
E
S
FIN
N
PL
Bitte lesen Sie vor Inbetriebnahme der Maschine unbedingt diese Betriebsanleitung
und beachten Sie die Sicherheitshinweise. Die Betriebsanleitung muss jederzeit
verfügbar sein.
Please read these operating instructions before putting the machine into operation
and observe the safety precautions. The operating instructions must always be
available.
Nous vous prions de lire attentivement le mode d’emploi avant d’utiliser la machine,
et attirons votre attention sur les consignes de sécurité. Les instructions d'utilisation
et les consignes de sécurité doivent toujours être disponibles. Les instructions
d'utilisation et les consi.
Leest u voor de ingebruik name van het apparaat a.u.b. deze gebruiksaanwijzing
goed door en neemt u de veiligheidsinstructies n acht. De gebruiksaanwijzing en
de veiligheids-voorschriften moeten altijd binnen handbereik zijn.
Per favore legga questo manuale di istruzione prima di mettere in funzione il
distruggidocumenti e osservi le regole di sicurezza. Le istruzioni d’uso devono
essere sempre disponibili.
Le recomendamos lea las instrucciones antes de poner en funcionamiento esta
máquina y cumpla las normas de seguridad. Las instrucciones de servicio y
seguridad deben estar siempre disponibles.
Läs igenom denna bruksanvisning innan ni startar maskinen. Var noga med
säkerhetsföreskrifterna. Instruktionsmanualen måste alltid finnas tillgänglig.
Lue nämä käyttö-ohjeet läpi ennenkuin käynnistät laitteen !
Noudata turvaohjeita. Käyttöohjeiden on oltava aina saatavilla.
Lees gjennom denne bruksannvisningen før De tar i bruk maskinen
Vær oppmerksom på sikkerhetsforskriftene. Opperatørmanualen
må alltid være tilgjengelig.
Proszę uważnie przeczytać instrukcję obsługi przed uruchomieniem urządzenia i
stosować się do przepisów bezpieczeństwa. Instrukcje obsługi muszą być
zawsze dostępne.
RUS Ïîæàëóéñòà, ïðî÷èòàéòå èíñòðóêöèþ ïî ýêñïëóàòàöèè ïåðåä óñòàíîâêîé
àïïàðàòà, ñîáëþäàéòå òåõíèêó áåçîïàñíîñòè. Èíñòðóêöèÿ ïî
ýêñïëóàòàöèè äîëæíà íàõîäèòüñÿ â äîñòóïíîì äëÿ ïîëüçîâàòåëÿ ìåñòå.
A gép üzembe helyezése elott figyelmesen olvassa el a kezelési utasítást és tartsa
be a biztonsági eloírásokat.Kezelési utasításnak mindig elérhetonek kell lennie.
TR Lütfen makineyi çalýþtýrmadan önce bu kullanma talimatlarýný dikkatli bir þekilde
okuyunuz ve belirtilen güvenlik önlemlerine uyunuz. Kullanma Talimatlarý
her zaman kullanýma hazýr olmalýdýr.
DK Før installation af maskinen bedes De venligst læse brugervejledningen
brugervejledningen og være opmærksom på sikkerhedsanvisningerne.
Brugervejledningen skal altid være tilgængelig.
CZ Prosím přečtěte si instrukce k obsluze a dodržujte bezpečnostní
upozornění. Návod k obsluze musí být vzdy dostupný.
P
Por favor leiam o manual de instruções antes de colocar a máquina em operação
e vejam as precauções de segurança. As instruções de operação deverão estar
sempre disponíveis.
GR ÐÁÑÁÊÁËÙ ÄÉÁÂÁÓÔÅ ÔÉÓ ÏÄÇÃÉÅÓ ×ÑÇÓÅÙÓ ÊÁÉ ÔÉÓ ÐÑÏÖÕËÁÎÅÉÓ
ÁÓÖÁËÅÉÁÓ ÐÑÉÍ ÂÁËÅÔÅ ÔÏ ÌÇ×ÁÍÇÌÁ ÓÅ ËÅÉÔÏÕÑÃÉÁ.
ÏÉ ÏÄÇÃÉÅÓ ×ÑÇÓÇÓ ÐÑÅÐÅÉ ÍÁ ÅÉÍÁÉ ÐÁÍÔÁ ÄÉÁÈÅÓÉÌÅÓ.
SLO Prosimo preberite navodila za uporabo ter upoštevajte varnostna opozorila
preden zaženete naparavo. Navodila naj bodo vedno pri roki.
SK Starostlivo si preštudujte tento návod na obsluhu pred uvedením stroja do
prevádzky a najmä bezpecnostné predpisy. Držte tento návod na obsluhu na
dostupnom mieste.
EST Palun lugege enne masina käivitamist käesolevat kasutusjuhendit ning järgige
ohutusnõudeid. Kasutusjuhend peab alati käepärast olema.
CHI
H
UAE
- 2-
• Safety precautions •
D
GB
F
NL
I
E
S
FIN
N
PL
RUS
H
TR
DK
CZ
P
GR
SLO
SK
EST
CHI
UAE
Keine Bedienung durch Kinder!
Children must not operate the machine!
Pas d‘utilisation par un enfant!
Geen bediening door kinderen!
Non lasciare utilizzare il tagliacarte a bambini!
No dejar que la utilicen los niños!
Installera maskinen utom räckhåll för barn!
Asentakaa laite lasten ulottumattomiin !
Installer maskinen utenfor rekkevidde for barn!
Dzieciom nie wolno obsługiwać urządzenia !
D
GB
F
NL
I
E
S
FIN
N
PL
RUS
H
TR
DK
CZ
P
GR
SLO
SK
EST
CHI
UAE
Nicht unter das Messer fassen!
Do not reach beneath the blade!
Ne pas passer les mains sous la lame!
Niet met de handen onder het mes komen!
Non toccare la lama nella parte inferiore!
¡No tocar debajo de la cuchilla!
Sträck inte in handen under kniven!
Älä laita kättäsi terän alle !
Plasser aldri hender ol. under kniven !
Nie wkładać rąk pod noże!
Íå äîïóñêàéòå äåòåé ê ïîëüçîâàíèþ àïïàðàòîì!
Gyerekek a gépet nem kezelhetik
Makinayý Çocuklar Kullanmamalýdýr.
Må kun betjenes af voksne
Stroj nesmí být obsluhován dětmi
As crianças não devem trabalhar com a máquina!
ÁÐÁÃÏÑÅÕÅÔÁÉ Ç ×ÑÇÓÇ ÁÐÏ ÐÁÉÄÉÁ.
Otroci ne smejo uporabljati naprave
So strojom nesmú pracovat deti!
Lapsed ei tohi masinat kasutada!
Èçáåãàéòå ïîïàäàíèÿ ðóê ïîä ëåçâèå!
Ne nyúljon a kés alá!
Elinizi býçaðýn altýna sokmayýnýz!
Stik ikke hænderne ind under knivbladet!
Nesahejte pod ostří nože!
Não tocar na parte inferior da faca!
ÌÇÍ ÁÃÃÉÆÅÔÅ ÔÏ ÊÁÔÙ ÌÅÑÏÓ ÔÇÓ ËÅÐÉÄÁÓ!
Ne segajte z roko pod rezilo!
Nevkladajte ruky pod nôž!
Ärge pange kätt tera alla!
-3-
• Safety precautions •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
D
Messer nie lose liegen lassen!
Messer nur mit Messerwechselvorrichtung oder im
Messertransportkasten befördern!
(siehe Seite 33 und 35).
Warnung! Verletzungsgefahr!
GB Never leave the blade unattended!
Do not extract or transport the blade without protection!
(See page 33 and 35).
Danger! Risk of injury!
F Ne jamais laisser la lame sans protections !
Elle ne doit être démontée qu’à l’ aide du dispositif de
changement de lame (cf. page 33 et 35), ou transportée dans
son étui en bois !
Danger! Risques de coupures !
NL Laat nooit de messen alleen achter.
Transporteer de messen niet zonder de houten bescherming
(zie pagina 33 en 35).
Waarschuwing! Opgelet voor ongevallen!
I
Non lasciare mai la lama incustodita. Non rimuovere o
trasportare la lama senza protezione. (Vedi pagina 33 e 35).
Attenzione! Rischio di infortunio!
E ¡No quitar la cuchilla sin prestar atención. No desmontar no
transportar la cuchilla sin protección! (vérase pág. 33 y 35)
¡Advertencia! ¡Peligro de hacerse daño!
S Lämna aldrig maskinen obemannad. Ta inte ur eller
transportera kniven utan skydd. (se sid 33 och 35).
Skaderisk!
FIN Käsittele terää aina varoen. Älä siirrä tai kuljeta
terää ilman suojaa ! (katso sivu 33 ja 35)
Loukkaantumisen vaara !
N La aldri kniven ligge ubeskyttet. Ta aldri ut kniven eller
transporter den uten beskyttelse (Se side 33 og 35)
FARE ! Muligheter for skade !
PL Nigdy nie pozostawiac nozy bez nadzoru.
Nie wyciagac lub transportowac nozy bez oslon!
(zobacz strona 33 i 35).
Ryzyko skaleczenia sie!
RUS Íå îñòàâëÿéòå îòêðûòîå ëåçâèå áåç ïðèñìîòðà! Íå
H
TR
ïûòàéòåñü èçâëå÷ü èëè òðàíñïîðòèðîâàòü ëåçâèå áåç
ñïåöèàëüíûõ ìåð ïðåäîñòîðîæíîñòè!
(Ñì. ñòðàíèöû 33 è 35)
Ñîáëþäàéòå âûøå ïåðå÷èñëåííûå ïðàâèëà
äëÿ èçáåæàíèÿ òðàâì!
Soha ne hagyja a kést őrizetlenül!
Ne vegye ki vagy ne szállítsa a kést védőtok nélkül!
(Lásd 33. és 35. oldal)
Veszély! Sérülésveszély!
Býçaðý hiçbir zaman gözetimsiz býrakmayýnýz!
Býçaðý muhafazasýz olarak yerinden çýkartmayýnýz veya
taþýmayýnýz! (Sayfa 33 ve 35’e bakýnýz)
Dikkat! Yaralanma riski!
-4-
• Safety precautions •
DK
Knivbladet må aldrig efterlades uden opsyn.
Forsøg ikke at afmontere eller transportere knivbladet uden
beskyttelse! (Se side 33 og 35)
FARE! Risiko for legemlig beskadigelse.
CZ Nikdy nenechávejte nůž bez krytu.
Nikdy nevyjímejte nebo neprepravujte nuz bez ochranného
krytu (viz. strany 33 a 35)
Nebezpecí! Riskujete zranení
P Deixar a faca sempre em local seguro!
Não retirar ou transportar a faca sem protecção!
(Ver pág. 33 e 35)
Perigo! Risco de dano!
GR ÌÇÍ ÁÖÇÍÅÔÅ ÔÇÍ ËÅÐÉÄÁ ÁÍÅÐÉÔÇÑÇÔÇ!
ÌÇÍ ÁËËÁÆÅÔÅ ¹ ÌÅÔÁÖÅÑÅÔÅ ÔÇÍ ËÅÐÉÄÁ ×ÙÑÉÓ
ÐÑÏÖÕËÁÎÇ (Äåßôå ó÷åôéêÜ óôéò óåëßäåò 33 & 35)
ÐÑÏÓÏ×Ç ! ÊÉÍÄÕÍÏÓ ÔÑÁÕÌÁÔÉÓÌÏÕ !
SLO Nikoli ne puščajte rezila nazaščitenega. Nikoli ne prenašajte
rezilo brez zaščite. ( glej stran 33 in 35).
Pozor! Nevarnost poškodbe.
SK Nenechávajte nôž nechránený (nezabezpecený)!
Nevyberajte alebo netransportujte nôž bez ochrany
(vid s. 33 a 35)
! Riziko úrazu !
EST Ärge jätke lõiketera kunagi järelevalveta!
Ärge pikendage ega teisaldage tera kaitseseadmeteta!
(Vt lk 33 ja 35)
Oht! Vigastuste oht!
CHI
33
UAE
35
33
-5-
35
• Safety precautions •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
D
GB
F
Keine harten und splitternden Materialien schneiden!
Do not cut hard materials or materials which may splinter!
La coupe de matériaux trop durs ou risquant des projections
est interdite !
NL Snij geen harde materialen of materiaal dat kan splinteren!
I
Utilizzare il tagliacarte esclusivamente per il taglio di risme
di carta o materiali analoghi!
E ¡No cortar materiales duros o materiales que puedan
astillarse!
S Förstör inte hârt material eller material som kan splittras!
FIN Asentakaa laite lasten ulottumattomiin !
N Ikke kutt hardt metall eller materiale som kan splintre !
PL Nie ciąć twardych materiałów lub materiałów, które mogą
ulec odpryśnięciu!
RUS Äàííûé ðåçàê íå ïðåäíàçíà÷åí äëÿ ðåçêè òâåðäûõ
H
TR
DK
ìàòåðèàëîâ èëè ìàòåðèàëîâ, êîòîðûå ìîãóò
ðàñùåïëÿòüñÿ!
Ne vágjon kemény vagy olyan anyagot, amely repedhet!
Sert veya parçalanabilecek malzemeleri kesmeyiniz!
Der må ikke skæres i hårde materialer eller i materialer, der
kan splintre!
CZ Neřežte tvrdý materiál, při kterém mohou ustřelovat ostré
úlomky!
P Não cortar materiais duros ou materiais que possam lascar!
GR ÌÇÍ ÊÏÂÅÔÅ ÓÊËÇÑÁ ÕËÉÊÁ ¹ ÕËÉÊÁ ÐÏÕ
ÈÑÕÌÌÁÔÉÆÏÍÔÁÉ!
SLO Nikoli ne režite trdih materialov ali materialov, ki se lahko
razcepijo.
SK Nerežte tvrdé materiály, alebo materiály, z ktorých môžu
vystrelovat ostré úlomky.
EST Ärge lõigake kõvasid materjale ega materjale, mis võivad
pilbasteks puruneda!
CHI
UAE
-6-
• Safety precautions •
The machine is designed for cutting stacks of
paper to a specified size.
This machine is constructed for "one-man
operation" only!
Warning! Clips or similar damage the
cutting blade.
Disconnect from the mains before starting any
service work or before removing the panels!
Replacement of blade and cutting stick may
be performed only when the main switch is
switched off!
-7-
• Safety precautions •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
All components which could endanger the
operator are covered by a guard!
A
A
A
Operating the machine without safety device is
forbidden!
(Front safety guard (A), rear screwed safety
guard (B) and panel (C).
B
C
A
C
-8-
• Safety precautions •
The dangerous cutting movement is
safeguarded by a movable guard (A) and a
safety two-handed control system! (B)
A
B
Before working with the machine and after
every blade replacement the automatic cut-off
function of safety guard (A),(correct if distance
between cover and table is < 20 mm) main
switch (B) and control panel (C) must be
checked.
C
-9-
• Safety precautions •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Protect mains cable against heat, oil and
sharp edges!
230V / 10A min
115V / 15A min
Connect the power cord to a single phase
socket.
Ensure free access to mains!
- 10 -
• Safety precautions •
When not in use for a longer period switch off.
(Main switch to "0").
Warning by IDEAL 4810-95
Danger!
Blade must always be covered by the
pressing bar
OK
Clamping
Blade
OK
- 11 -
• Installation •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Only IDEAL 4810-95, IDEAL 4850-95/EP,
IDEAL 6550-95EP
Remove the stand from the wooden pallet.
Only IDEAL 4810-95, IDEAL 4850-95/EP,
IDEAL 6550-95EP
4 strong people are required to lift the machine
from the pallet and place it on the stand.
Secure with 4 screws (A). Put the shelf (B) on
the stand. (Parts and tools are in the tool set
(C).
B
4x
A
C
- 12 -
• Installation •
A
C
IDEAL 5221-95EP
The machine is delivered ready for operation.
4 strong people are required to lift the
machine from the pallet.
Side tables, left and right, (A) are available
as accessories.
Attach the side tables to the front table so
that the upper surface is level.
(Screws and nuts are in a plastic bag in the
tool set (C).
The front and rear wooden panels must be
removed for in-house transport on a pallet
truck.
For transport through narrow doors:
• Remove side tables
• Remove the machine from its base
(4 screws)
• Tilt the machine on its side
• Mount the machine to its base
• Screw on all side panels
Only IDEAL 4810-95, IDEAL 4850-95
Tighten the backgauge crank (A). Parts and
tools are in the tool set (C).
C
A
- 13 -
• Installation •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
C
Only IDEAL 4810-95
Attach the enclosed hand-wheel for clamping.
Parts and tools are in the tool set (C).
Plug into socket.
The machine must be connected directly to the
socket.
- 14 -
• Operation •
It is forbidden to operate the machine if the
operating and safety instructions have not been
understood. Please check the safety devices
are functioning and complete before use.
• All covers have to be mounted (A).
• The release for cutting is allowed only if
the cover is closed and the two-hand safety
device is operated at the same time (B)
• If the front cover closes by itself the
gas spring (X) needs replacing.
A
A
We recommend you keep a record of your test
results.
A
B
B
X
- 15 -
• Operation •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Position the main switch to "I" (A). Insert the
key for the control system and move it to the
right (B). Open the safety guard (C). The
machine is now ready for use.
D
Only IDEAL 4850-95EP, IDEAL 5221-95EP,
IDEAL 6550-95EP
Press
button (D).
Machine will automatically go to the start
position.
S
B
A
C
IDEAL 4810-95, IDEAL 4850-95,
The measurement is set with the backgauge
crank (A). Proceed to position
generally
from the rear.
The measurement is shown on the scale (B)
just below the indicator and can be read in
mm/cm or inches.
B
A
- 16 -
• Operation •
B
IDEAL 4810-95EP, IDEAL 4850-95EP,
IDEAL 5221-95EP, IDEAL 6550-95EP
The measurement is set either with the handwheel (A) or by programming (B) the cutting
measurements. Measurement is shown on the
display in inches or cm (B).
A
- 17 -
• Operation •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
A
B
Optical cutting line (A) that indicates the exact
position of the cut. Blade cuts on the front
edge (B) of the light beam. (Only use when no
exact cut is required).
IDEAL 4810-95 has no cutting line indicator.
Only IDEAL 4810-95, IDEAL4850-95.
Pull out the handle to avoid the measurement
being wrongly adjusted.
- 18 -
• Operation •
B
A
C
Position the paper on the backgauge (A) and
side lays left or right (B).
To move paper stacks, please use the paper
knock-up block (C) provided.
(Run backgauge to the front for turning the
paper stack).
B
- 19 -
• Operation •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
IDEAL 4850-95/EP, IDEAL 5221-95EP
IDEAL 6550-95/EP
The clamp moves automatically when cutting
is activated.
The paper can also be pressed in advance.
Clamping and cutting is activated by
pressing button (A) on the front table.
A
+
=
Pre-clamping
+
=
Clamp returns
+
=
Cutting sequence with automatic clamping
Only 4810-95
Clamping is released by the hand-wheel.
Before every cut lower the clamp by turning the
hand-wheel to the right and tighten with a light
twist. The cut is activated by pressing the two
buttons exactly at the same time.
- 20 -
• Operation •
Close the safety guard.
Cutting activation:
Press both buttons of the two-handed control
system activation (A) simultaneously and them
pressed until the paper is completely cut.
To interrupt or stop cutting:
To interrupt or stop cutting, release
both buttons (A) of the two-hand control.
- 21 -
• Operation •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Operating elements
A - Front safety guard
two-handed control system
B - Safety
Pre-clamping and cutting
switch
C - Overload
(blade drive/clamp drive/
backgauge drive)
D - Backgauge control (EP)
clamp
E - Paper
(only IDEAL 4810-95)
F - Main switch
(EP) or crank handle
G - Hand-wheel
for backgauge setting
H - Key switch
I - Backgauge
J - Side lay left and right
K - Display cutting size (EP, cm or inch)
program step up (Programming)
L - Select
or fixed dimension (Standard 21 cm)
program step down (Programming)
M - Select
or fixed dimension (Standard 10,5 cm)
N - Stop and delete input
O - Start
P - Memory multiple cut
Q - Keypad
R - Changeover cm - inch (LED - display)
S - Clear program
T - Select program
U - Enter
V - Program number
W - Program step
X - Cut is blocked
Y - Display multiple cut
- 22 -
• Operation •
IDEAL 4810-95, IDEAL 4850-95/EP,
IDEAL 5221-95EP, IDEAL 6550-95EP
Start machine
• Main switch to position "I", insert the key
for the control panel and turn it to the right.
Open the front safety guard
• Press
button
backgauge moves
to the rear and searches for the reference
position, wait until a measurement
is shown in the display
IDEAL 4810-95
= 45 cm, 17,72 inches
IDEAL 4850-95/EP = 45 cm, 17,72 inches
IDEAL 5221-95EP = 52 cm, 20,47 inches
IDEAL 6550-95/EP = 61 cm, 24,02 inches
F
H
A
O
S
I
D.
Warning!
Before storing or cutting a measurement
please check if the correct measurement
scale (cm or inch) see above is stored.
For information on how to store see picture
below left.
Cutting to specified dimensions
• Enter dimension on the numerical key pad
LED "S" appears.
(If a wrong dimension is entered this can be
button).
corrected by pressing the
button
dimension is
• Press
approached,
LED "S" disappears.
Dimensions below 9 cm 3,5 cm (IDEAL
6550-95EP 2,5 cm) can only be approached
button pressed and held. (When
with the
button
is released, the backgauge
the
moves to a measurement of 9 cm
measurement 9 cm blinks, keep
button pressed, backgauge
moves
the
to e.g. 7 cm.
• Insert paper and move by means of the
and side
stacking angle to the backgauge
lay on the left .
• Only IDEAL4810-95
Turn the hand-wheel for paper clamping to
the right and tighten with a short twist.
• Close the front safety guard
• Release the cut.
Q
X
s
S
I
S
S
O
I
S
I
J
E
A.
Cut according to markings
• Adjust the backgauge with the hand-wheel or
crank handle to the back.
• Insert paper and move by means of the
stacking angle to the backgauge and side
lay on the left
• Turn the hand-wheel or crank handle to
the right until the marking on the paper to be
cut is below the cutting line indicator.
IDEAL 4810-95 has no cutting line indicator.
G
J.
- 23 -
I
G
• Operation •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Only EP machines.
• The further the hand-wheel
is turned to the right, the quicker the
backgauge moves. If the hand-wheel is turned
to the left the backgauge will return quicker.
Only IDEAL4810-95
• Turn the hand-wheel for paper clamping to
the right and tighten with a short twist.
• Close the front safety guard
• Release the cut.
G
E
A.
Eject function
,
If button j is pressed instead of button
after inserting the measurement , the
backgauge will advance forwards so that paper
can be removed. Finally the backgauge moves to
the last setting.
M
SO
Q
Adjust the eject-dimension
• Press , hold, and press
e on display.
• Insert the desired dimension.
(Standard is 20 cm).
•
Store dimension.
•
+ Escape the program mode.
p
T
g
p s
Program buttons b and j programs
Press , hold, and press b (ö appears on
the display) or
Press , hold, and press j (Ü appears on
the display)
• Enter the desired dimension (For example:
29,7 cm x 21 cm can be entered for DIN A4)
• Store dimension.
p
p
g
Display in cm or inch
display changes between cm and
inch (see page 23).
• Press
i
Cutting activation
Warning!
• Run backgauge to the front for turning the
paper stack.
• Do not interrupt the upward movement of the
blade by performing switching procedures.
• Release blade only when LED "S" has gone
out.
• Close the front safety guard .
• Blade must always be at the top and be
covered by the clamp. Do not touch the blade.
(see safety information on page 38).
Risk of injury!
X
A
- 24 -
• Operation •
Multiple cut
• Enter the multiple cut size on the display
• Advance to the measurement with the
button.
• Push the paper to the backgauge .
• Press button the red LED "M " light
will be on.
• Enter the multiple cut size.
• After cutting has been activated press
button.
Every time the
button is pressed, the
backgauge will advance by the multiple cut
size.
• Pressing the button shows the actual
size.
Q.
S
I
T
Y
S
S
s
N
Exiting program-mode
• Press button LED "M "
on the display.
T
- 25 -
Y is cleared
• Operation •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Programming
Only IDEAL 4850-95EP, IDEAL 5221-95EP,
DEAL 6550-95EP
This control system enables you to store 99
programs with 99 programmable steps. One
step represents one measurement. After
entering the program numbers you are able to
change between several program steps with
the button j and b .
First figure on display = program number.
Second figure = program step.
Dimensions below 9 cm/3,54 inch can only
button held pressed.
be approached with the
the entered dimension is
"u" on the display
too low.
the entered dimension is
"o" on the display
too high.
Each program step corresponds to one
dimension. The indicated program step can be
overwritten at any time. These programs
remain stored when the machine is off. Should
you change to another dimension unit all
programmed measurements are converted into
the new unit (cm or inch).
S
Entering a program
• Press p P appears on the display.
• 01 ... 99 Enter program number 01 ... 99.
(Top number on display = program number).
• If measurement is shown on the display
the
program is reserved.
• Enter dimension, or move the backgauge to
the desired measurement with the
hand-wheel .
• Store the dimension next program step
appears .
• Enter the next dimension.
Should an ejection be desired before this cut
press , hold, and press .
• Store the dimension next program step
appears.
• Should the entered program be required
(program is closed).
immediately
press
Press
again (backgauge moves to the
dimension of the first program).
Or:
• + Escape the program mode.
V
G
g
g
W
p
S
p s
- 26 -
K
T
S
• Operation •
Eject function program
The eject function can be added each time a
measurement is entered and ejects before
advancing to the next measurement.
An eject at the end of a program must be
programmed in the first step at the program.
If the dimension and eject function are stored in
the program step the program number appears
on the display .
V
Example of a program eject function
•
program 08
•
delete previous program
•
step 1 on 16,0 cm
•
step 2 on 20,0 cm
• Press , hold, and press
eject (e blinks)
•
Store the dimension
•
escape the program mode
p08
cc
16g
20
p
g
ps
T
How the example works
start program 08
•
•
proceeds to position
• Insert paper
• Release cut 1
• Press
button
• Paper is ejected ( blinks)
• Turn the paper
• Release cut 2
•
escape the program mode
p08
S
S
V
ps
Programming of multiple cut dimension
• Press "X" appears on the display.
•
...
Enter program number 01 ... 99.
Top number on display = program number.
Lower number = program step.
• Enter the cut size on the display .
• Store the dimension.
• Enter multiple cut size.
Press
button E
and multiple cut size
appears on the display.
Press
button again F ..... N.
• Store the dimension.
• + Escape the program mode.
Maximum nine multiple cuts can be entered.
p
01 9 9
Q
g
T
T
g
p s
- 27 -
W
• Operation •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Cancel a program
• p press "X" appears on the display.
• 0 1 ... 9 9 Enter program number 01 ... 99.
• Press button c twice.
Each program has to be cancelled separately.
Deleting a dimension when programming
and overwrite the dimension.
Press
s
Choose a program step appears.
Press , hold, and press
ß
Enter the desired number of steps (e.g.
p
T
W lights.
0 5).
Change a step
b next step
j previous step
Insert a step
Press , hold, and press b A new
program step is inserted before the displayed
program step is shown.
p
Delete a step
Press , hold, and press j
Program step
is deleted.
The following number of steps are updated.
p
- 28 -
• Operation •
Working with programs
"X" appears on the display
• Press
•
...
Enter program number 01 ... 99
With the button j and b you are able to
change between several program steps.
With
the backgauge moves to the indicated
dimension.
With
the backgauge stops.
p
01 99
S
s
General
LED "S" lights
Cut is blocked.
LED "S" is off
the actual dimension appears.
In the program mode the ejection of paper j
is not possible. The ejection of paper has to
be programmed.
Escape the program mode
• Press
"X" appears on the display.
• Press
escape the program mode.
p
s
- 29 -
• Blade and cutting stick replacement •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
If the cutting quality decreases:
• Check the cutting depth (see page 38).
• Check the cutting stick (see page 34).
• Replace or grind the blade (see page
28 - 38).
The blade cannot be ground if the blade
height is less than 83 mm/3,29 inches.
A new blade must be used.
The blade may only be ground by a qualified
supplier or from the manufacturer
Krug & Priester, D-72336 Balingen.
Danger! Risk of injury!
The blade is extremely sharp. Do not extract or
transport the blade without protection. Changing the blade may only be performed by
trained staff.
- 30 -
• Blade and cutting stick replacement •
Turn the blade depth adjustment screw to the
left until it stops. (Screwdriver found in tool set
(A).
Close the safety guard (1.).
Lower the blade by pressing both cutting
buttons (2.). Keep one button pressed and
turn off the main switch (3.).
- 31 -
• Blade and cutting stick replacement •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
The 3 eccentrics are now exposed and should
be turned counter clockwise to position "0"
with the special wrench and attachable
extension pipe (A) (in the tool set). The slot
must correspond to position "0" (B).
C
A
Only IDEAL 4810-95, 4850-95/EP
Unscrew the blade screws (C) on the right
hand side.
B
Remove the special wrench and turn on the
main switch until the blade returns to the home
position.
Warning by IDEAL 4810-95
Do not turn main switch to position
"0" whilst blade is moving upwards! The
clamp must always overlap the blade!
Danger! Risk of injury!
OK
Clamping
Blade
OK
- 32 -
• Blade and cutting stick replacement •
A
Position the main switch to "0" (1.)
Remove the 2 blade screws on the elongated
holes (2.). Then put the blade changing tool (A)
into place and fasten it to the blade (3.).
3.
2.
1.
1.
3.
B
4.
A
Remove 2 blade screws (1.)
IDEAL 4810-95, IDEAL 4850-95/EP
and 3 blade screws (1.) IDEAL 5221-95EP,
IDEAL 6550-95EP.
Loosen the grips (2.) of the blade changing
tool (A) lightly and allow the blade to be taken
downwards out of the machine (3.). Place the
blade into the blade carrier (B) and screw it
into place (4).
2.
- 33 -
• Blade and cutting stick replacement •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Take out the cutting stick with a small screwdriver. If needed the cutting stick can be turned
or exchanged. (The cutting stick can be used
eight times).
Replacing the cutting stick (not the blade)
• Turn the blade adjusting screw (A) to the left
until it stops.(Otherwise the first cut will be too
deep).
• Remove the cutting stick according to top
picture.
• Turn the cutting stick (the non-used side must
be near to the blade) and plug it into the
holding bolt.
Danger! Risk of injury!
Cutting test after replacing the cutting stick
(not the blade)
• Insert the paper and release the cut.
• If the last sheet of paper is not cut along the
entire length turn the blade adjusting screw
(A) ¼ turn to the right.
• If the last sheet is still not completely cut
repeat this process until the last sheet is cut
along the entire length.
- 34 -
• Blade and cutting stick replacement •
Take the exchange blade carefully out of the
blade box and screw it to the blade changing
tool (A)
• Make sure there is a space ot 11 mm
or 0.43 inches! (B).
• Blade must be covered! (C).
Danger! Risk of injury!
A
11 mm
0.43 inch
B
B
C
C
1.
A
Place the blade to be exchanged with the
blade changing tool (A) mounted (1.), into the
blade carrier and push it up to the top and
screw it into place with the grips (2.).
2.
- 35 -
• Blade and cutting stick replacement •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Lightly tighten 3 (IDEAL 4810-95,
IDEAL 4850-95/EP has 2) of the 5 blade
screws with washers (1.). Remove the blade
changing tool (2.). Lightly tighten the
remaining blade screws with washers (3.).
1.
A
2.
IDEAL 4810-95 and IDEAL 4850-95/EP
Lightly screw in the right blade screw with the
washer (A) when the blade is lowered.
3.
Remove all tools and distribute paper along
the entire cutting length (1.).
Turn main switch to position "I" (2.).
1.
2.
- 36 -
• Blade and cutting stick replacement •
1.
3.
Close the safety guard (1.) Lower the blade by
pressing both cutting buttons (2.). Keep one
button pressed and turn off the main switch (3.).
2.
Open the safety guard (4.). With the special
wrench (B) the 3 eccentrics should be screwed
down (5.)until the paper is cut along the
entire length of the blade (The blade must
remain parallel, not too deep into cutting stick).
4.
A
5.
Only IDEAL 4810-95 and
IDEAL 4850-95/EP
Tighten the blade screws (A) on the right hand
side.
A
2.
Turn main switch to position "I" (1.). Blade will
return to upper position. Tighten the blade
screws (2.) firmly.
Warning by IDEAL 4810-95
Do not turn main switch to position
"0" whilst blade is moving upwards! The
clamp must always overlap the blade!
Danger! Risk of injury!
1.
- 37 -
• Blade and cutting stick replacement •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Paper cutting test. If the last sheet or several
sheets are not completely cut, gradually turn
the knob for blade depth adjustment (A)
¼ turn to the right until the paper is cut along
the entire length. Do not set too low as blade
will become blunt sooner.
A
OK
Clamping
Warning by IDEAL 4810-95
Danger!
Blade must always be covered by the
pressing bar (see picture below at the left).
Blade
OK
- 38 -
• Maintenance and cleaning •
Maintenance work may only be performed by
trained staff.
Danger! Disconnect the mains before
starting any service work or before
removing the cover.
D
Grease the backgauge (A) control weekly with
a grease gun. Advance the backgauge as far
as possible to the front. (Use non-resinous oil
or grease).
Grease the remaining parts twice a year (see
picture).
The main switch must be on "0" (B).
Remove lower panel and rear wooden panel
(C). Tools in tool set.
• Remove any paper.
• Grease the machine.
• Check the 4 joining bolts and 2 pushing bars
for wear (D). If necessary inform your service
personnel.
• Mount the machine.
= Greasing points on the machine.
- 39 -
• Maintenance and cleaning •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Safety test
The safety regulations are according to the
regulations of the country where the cutting
machine is operated. The manufacturer
recommends a safety check is made every 5
years by an authorised service team.
- 40 -
• Possible malfuntions •
Machine does not function!
Is the machine plugged in?
Main switch to position "I"? (A)
Control system activated? (B)
(Turn key to the right)
Release a cut see page 21.
- 41 -
• Possible malfuntions •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Cut cannot be made.
• If cover is open:
close it.
• If cover is closed:
open and re-close it. (Security check).
- 42 -
• Possible malfuntions •
Machine turns off:
• Machine overloaded.
Safety button (A) ejects.
(Allow 1 minute cooling time and reset the
safety button (A).
Machine
blocked.
•
• Blade is blunt.
Eliminate the cause, and push the safety
button (A).
A, B
Only IDEAL 4850-95EP,
IDEAL 5221-95EP, IDEAL 6550-95EP
• Backgauge blocked
Safety button (B) ejects.
Eliminate the cause, and push the safety
button (B).
Safety button for:
A = Blade drive
A = Clamping drive
B = Backgauge drive
- 43 -
• Possible malfuntions •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
A
Does not cut through the last sheet:
• Turn or turn around the cutting stick (A),
readjust the blade by means of the blade
adjusting knob (B)
(see page 38).
Poor cutting quality or blade stays in the
paper stack.
• Change the blade (C) (see pages 30 - 38.
B
C
- 44 -
• Possible malfuntions •
IDEAL
"Service"
Motor runs but blade does not move
downwards.
• Security brake has been activated!
Inform the Service Team!
• www.ideal.de "Service"
[email protected]
Display illumination off
• Machine is plugged in? (A)
• Main switch on position "I"? (B)
• Push in the safety button! (C)
• Check the units fuse and the on-site circuit
breaker!
A
B
C
- 45 -
• Possible malfuntions •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
IDEAL 4850-95EP, IDEAL 5221-95EP,
IDEAL 6550-95EP
Cut cannot be made.
• Measurement has not been reached
correctly.
• LED "S" does not turn off.
Push the
button again.
Check the security cover (see page 42).
X
S
• Measurement below 9 cm/3,54 inch
Hold the
button
is achieved.
S
IDEAL
"Service"
O until the measurement
None of the above mentioned methods
helped to solve the problem:
Contact Service Team under
• www.ideal.de "Service"
[email protected]
- 46 -
• Accessories •
Recommended accessories:
Blade
• Nr. 9000 021 IDEAL 4810-95
• Nr. 9000 021 IDEAL 4850-95/EP
• Nr. 9000 130 IDEAL 5221-95EP
• Nr. 9000 025 IDEAL 6550-95/EP
Cutting stick (6 pieces)
• Nr. 9000 022 IDEAL 4810-95
• Nr. 9000 022 IDEAL 4850-95/EP
• Nr. 9000 024 IDEAL 5221-95EP
• Nr. 9000 026 IDEAL 6550-95/EP
Blade changing tool 1
• Nr. 9000 518 IDEAL 4810-95
• Nr. 9000 518 IDEAL 4850-95/EP
• Nr. 9000 512 IDEAL 5221-95EP
• Nr. 9000 513 IDEAL 6550-95/EP
Paper knock-up block 1
• Nr. 9000 521 IDEAL 4810-95
• Nr. 9000 521 IDEAL 4850-95/EP
• Nr. 9000 521 IDEAL 5221-95EP
• Nr. 9000 521 IDEAL 6550-95/EP
Side tables left and right
• Nr. 9000 530 IDEAL 5221-95EP
1
Included in delivery
- 47 -
• Technical data •
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Technical data:
• Power supply: 230V/50Hz/1~,115V/60Hz/1~
• Cutting height: 80 mm
• Sound level EN 13023: < 70 dB (A)
A
The exact technical specifications can be
found on the technical specifications sticker (A)
on the machine. A wiring diagram is found in
the electrical switch box.
To claim under guarantee, the machine must still
carry its original identification label.
IDEAL 4810-95
IDEAL 4850-95
IDEAL 4850-95 EP
IDEAL 5221-95 EP
IDEAL 6550-95 EP
Cuttinglength
mm
Tabledepth
mm
Minimum space
requirement
(B X T X H) mm
Weight
kg
475
475
475
520
650
458
458
450
520
610
755 x 970 x 1360
755 x 970 x 1230
755 x 970 x 1230
855* x 1067 x 1260
995 x 1260 x 1220
194
209
215
262**
304
* with side tables: 1560 mm
** with side tables: 276 kg
- 48 -
• Technical data •
This machine is approved by independent
safety laboratories and is in compliance with the
EC-regulations 98/37/EG, 2006/95/EG and
2004/108/EG.
Sound level information:
The sound level is < 70 db (A) as defined by
EN 13023.
Subject to alteration without notice.
- 49 -
IDEAL 4810-95 • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
D
GB
F
NL
I
E
EG-KONFORMITÄTSERKLÄRUNG
EC-declaration of conformity
Déclaration de conformité CE
EG-verklaring van overeenstemming
Dichiarazione CE di conformità
Declaración CE de conformidad
- Hiermit erklären wir, daß die Bauart von
- Herewith we declare that
- Par la présente, nous déclarons que
- Hiermede verklaren wij, dat de in de handel gebrachte machine
- Si dichiara che il modello della
- Por la presente, declaramos que la
4850-95 EP: 5221-95 EP; 6550-95 EP:
4810-95; 4850-95.
- folgenden einschlägigen Bestimmungen entspricht
- complies with the following provisons applying to it
- sont conformes aux dispositions pertinentes suivantes
- voldoet aan de eisen van de in het vervolg genoemde bepalingen
- è conforme alle seguenti disposizioni pertinenti
- satisface las disposiciones pertinentes siguientes
98/37/EG; 2006/95/EG; 2004/108/EG.
- Angewendete harmonisierte Normen insbesondere
- Applied harmonised standards in particular
- Normes harmonisées utilisées, notamment
- Gebruikte geharmoniseerde normen, in het bijzondere
- Norme armonizzate applicate in particolare
- Normas armonizadas utilizadas particularmente
EN 60204-1; EN 1010-1; EN 1010-3;
EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3;
EN ISO 12100-1; EN ISO 12100-2; EN ISO 13857; EN 954-1; EN 13023;
EN ISO 11204
Krug & Priester GmbH u. Co KG
72336 Balingen, Germany
- 50 -
01.08.2008
Datum
Wolfgang Priester
- General Manager -
Remarks:
- 51 -
IDEAL • Made in Germany
Document Shredders
•
IDEAL Krug & Priester
•
72336 Balingen
•
Germany
•
www.ideal.de
•
Printed in Germany • IDEAL 09/2008
Trimmers and Guillotines
">