Imagine Communications Selenio 6800 WCLK6801+ WordClock Distribution Amplifier Installation and Operation Manual
Pubblicità
Pubblicità
Installation and Operation Manual
Selenio 6800™ WCLK6801+
WordClock Distribution Amplifier
Installation and Operation Manual
Edition A
175-100460-00
Delivering the Moment
Publication Information
© 2014 Imagine Communications Corp. Proprietary and Confidential.
Imagine Communications considers this document and its contents to be proprietary and confidential. Except for making a reasonable number of copies for your own internal use, you may not reproduce this publication, or any part thereof, in any form, by any method, for any purpose, or in any language other than English without the written consent of Imagine Communications. All others uses are illegal.
This publication is designed to assist in the use of the product as it exists on the date of publication of this manual, and may not reflect the product at the current time or an unknown time in the future. This publication does not in any way warrant description accuracy or guarantee the use for the product to which it refers. Imagine Communications reserves the right, without notice to make such changes in equipment, design, specifications, components, or documentation as progress may warrant to improve the performance of the product.
Trademarks
6800+™, ADC™, CCS Navigator™, Channel ONE™, ChannelView™, ClipSync™, Delay™, D Series™, D Series DSX™, Deliver the Moment™, Delivering the Moment™, FAME™, Farad™, G8™, G Scribe™, HView™, IconMaster™, IconLogo™, IconStation™, IconKey™, InfoCaster™, InfoCaster Creator™, InfoCaster Manager™, InfoCaster Player™, InstantOnline™, Invenio®,
Live Update™, mCAPTURE™, Magellan™, Magellan CCS Navigator™, Magellan Q SEE™, MultiService SDN™, NetPlus™,
NetVX™, NewsForce™, Nexio® G8™, Nexio AMP® ChannelView™, Nexio® Channel ONE™, Nexio® ClipSync™, Nexio®
Delay™, Nexio® Digital Turnaround Processor™, Nexio® Farad™, Nexio® G Scribe™, Nexio® IconKey™, Nexio® IconLogo™,
Nexio® IconMaster™, Nexio® IconStation™, Nexio® InfoCaster™, Nexio® InfoCaster Creator™, Nexio® InfoCaster Manager™, Nexio® InfoCaster Player™, Nexio® InfoCaster Traffic™, Nexio® InstantOnline™, Nexio® mCAPTURE™, Nexio® News-
Force™, Nexio® NXIQ™, Nexio® Playlist™, Nexio® Remote™, Nexio®RTX Net™, Nexio® TitleMotion™, Nexio® TitleOne™,
Nexio® Velocity ESX™, Nexio® Velocity PRX™, Nexio® Velocity XNG™, Nexio® Volt™, OPTO+™, Panacea™, Platinum™,
Playlist™, Predator II GRF™, Predator II GX™, Punctuate™, Remote™, RTX Net™, QuiC™, Q SEE™, SD STAR™, Selenio™,
Selenio 6800+™, SelenioNext™, Selenio X50™, Selenio X85™, Selenio X100™, TitleMotion™, TitleOne™, Velocity ESX™,
Velocity PRX™, Velocity XNG™, Versio™, Videotek® SD STAR™, X50™, and X85™ are trademarks of Imagine Communications or its subsidiaries.
Altitude Express®, Connectus®, Enabling PersonalizedTV®, ICE® Broadcast System, ICE Illustrate®, ICE Q® algorithms, ICE-
PAC®, Imagine ICE®, Inscriber®, Inscriber® Connectus®, Invenio®, NEO®, Nexio®, Nexio AMP®, PersonalizedTV®, Router-
Works®, Videotek®, Videotek® ASI STAR®, Videotek® GEN STAR®, and Videotek® HD STAR® are registered trademarks of
Imagine Communications or its subsidiaries.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation. HD BNC is a trademark of Amphenol
Corporation. Some products are manufactured under license from Dolby Laboratories. Dolby and the double D symbol are registered trademarks of Dolby Laboratories. DTS Neural audio products are manufactured under license from DTS
Licensing Limited. DTS and the Symbol are registered trademarks & the DTS Logos are trademarks of DTS, Inc. © 2008
2010 DTS, Inc. All other trademarks and trade names are the property of their respective companies.
Contact Information
Imagine Communications has office locations around the world. For locations and contact information see:
http://www.imaginecommunications.com/contact us/
Support Contact Information
For support contact information see:
▪
▪ Support Contacts: http://www.imaginecommunications.com/services/technical support/ eCustomer Portal: http://support.imaginecommunications.com
© 2014 Imagine Communications Corp. Proprietary and Confidential
WCLK6801+
WordClock
Distribution Amplifier
Installation and Operation Manual
Edition A
April 2013
Contents
Preface
..........................................................................................................................v
Waste from Electrical and Electronic Equipment (WEEE) Directive .............................. vii
Chapter 1 Introduction
.............................................................................................................. 1
Chapter 2 Installation and Operation
................................................................................ 3
iii
iv
Chapter 3 Specifications
......................................................................................................... 13
Appendix A Communication and Control Troubleshooting Tips
............................. 15
Index
........................................................................................................................... 19
Preface
Manual Information
Purpose
This manual details the features, installation, operation, maintenance, and specifications for the WCLK6801+ WordClock Distribution Amplifier.
Audience
This manual is written for engineers, technicians, and operators responsible for the installation, setup, and/or operation of the WCLK6801+ WordClock Distribution Amplifier.
Revision History
Table 1-1 Document Revision History
Edition
A
Date
April 2013
Revision History
Product release
Writing Conventions
To enhance your understanding, the authors of this manual have adhered to the following text conventions:
Table 1-2 Writing Conventions
Term or
Convention
Bold
Description
Italics
CAPS
Code
Indicates dialog boxes, property sheets, fields, buttons, check boxes, list boxes, combo boxes, menus, submenus, windows, lists, and selection names
Indicates E-mail addresses, the names of books or publications, and the first instances of new terms and specialized words that need emphasis
Indicates a specific key on the keyboard, such as ENTER, TAB, CTRL, ALT, or DELETE
Indicates variables or command-line entries, such as a DOS entry or something you type into a field v
vi
Preface
Table 1-2 Writing Conventions (Continued)
Term or
Convention
>
Description
hyperlink
Internet address
Indicates the direction of navigation through a hierarchy of menus and windows
Indicates a jump to another location within the electronic document or elsewhere
Indicates a jump to a website or URL
Indicates important information that helps to avoid and troubleshoot problems
Obtaining Documents
Product support documents can be viewed or downloaded from our website. Alternatively, contact your Customer Service representative to request a document.
Unpacking/Shipping Information
Unpacking a Product
This product was carefully inspected, tested, and calibrated before shipment to ensure years of stable and trouble-free service.
1
Check equipment for any visible damage that may have occurred during transit.
2
Confirm that you have received all items listed on the packing list.
3
Contact your dealer if any item on the packing list is missing.
4
Contact the carrier if any item is damaged.
5
Remove all packaging material from the product and its associated components before you install the unit.
Keep at least one set of original packaging, in the event that you need to return a product for servicing.
Product Servicing
Except for firmware upgrades, the WCLK6801+ module is not designed for field servicing.
All hardware upgrades, modifications, or repairs require you to return the modules to the
Customer Service center.
Returning a Product
In the unlikely event that your product fails to operate properly, contact Customer Service to obtain a Return Authorization (RA) number, and then send the unit back for servicing. If the original package is not available, you can supply your own packaging as long as it meets the following criteria:
WCLK6801+
Installation and Operation Manual
vii
The packaging must be able to withstand the product’s weight.
The product must be held rigid within the packaging.
There must be at least 2 in. (5 cm) of space between the product and the container.
The corners of the product must be protected.
Ship products back to us for servicing prepaid and, if possible, in the original packaging material. If the product is still within the warranty period, we will return the product prepaid after servicing.
Restriction on Hazardous Substances (RoHS) Directive
Directive 2002/95/EC—commonly known as the European Union (EU) Restriction on
Hazardous Substances (RoHS)—sets limits on the use of certain substances found in electrical and electronic equipment. The intent of this legislation is to reduce the amount of hazardous chemicals that may leach out of landfill sites or otherwise contaminate the environment during end-of-life recycling. The Directive, which took effect on July 1, 2006, refers to the following hazardous substances:
Lead (Pb)
Mercury (Hg)
Cadmium (Cd)
Hexavalent Chromium (Cr-V1)
Polybrominated Biphenyls (PBB)
Polybrominated Diphenyl Ethers (PBDE)
In accordance with this EU Directive, products sold in the European Union will be fully
RoHS-compliant and “lead-free.” Spare parts supplied for the repair and upgrade of equipment sold before July 1, 2006 are exempt from the legislation. Equipment that complies with the EU directive will be marked with a RoHS-compliant symbol, as shown in
Figure 1-1 RoHS Compliance Symbol
Waste from Electrical and Electronic Equipment (WEEE) Directive
The European Union (EU) Directive 2002/96/EC on Waste from Electrical and Electronic
Equipment (WEEE) deals with the collection, treatment, recovery, and recycling of electrical and electronic waste products. The objective of the WEEE Directive is to assign the responsibility for the disposal of associated hazardous waste to either the producers or users of these products. As of August 13, 2005, producers or users are required to recycle electrical and electronic equipment at end of its useful life, and must not dispose of the equipment in landfills or by using other unapproved methods. (Some EU member states may have different deadlines.)
In accordance with this EU Directive, companies selling electric or electronic devices in the
EU will affix labels indicating that such products must be properly recycled. Contact your local Sales representative for information on returning these products for recycling.
Equipment that complies with the EU directive will be marked with a WEEE-compliant symbol, as shown in
viii
Preface
Safety
Figure 1-2 WEEE Compliance Symbol
Safety
Carefully review all safety precautions to avoid injury and prevent damage to this product or any products connected to it. If this product is rack-mountable, it should be mounted in an appropriate rack using the rack-mounting positions and rear support guides provided. To protect a frame from circuit overloading, connect each frame to a separate electrical circuit.
If this product relies on forced air cooling, all obstructions to the air flow should be removed prior to mounting the frame in the rack.
If this product has a provision for external earth grounding, ground the frame to the earth using the protective earth ground on the rear panel.
IMPORTANT!
Only qualified personnel should perform service procedures.
Safety Terms and Symbols in this Manual
WARNING
Statements identifying conditions or practices that may result in personal injury or loss of life. High voltage is present.
CAUTION
Statements identifying conditions or practices that can result in damage to the equipment or other property.
1
Introduction
Product Description
The WCLK6801+ module distributes WordClock reference signals required for timing distribution in audio, production, and post-production. The module supports the
WordClock, 1 PPS, and 10 MHz standards.
Main Features
The following are the main features of the WCLK6801+:
SDIF-2 Word Clock compliant
Supports WordClock, 1 PPS, and 10 MHz signal types
Supports the following input clock frequencies:
WordClock signals: 32-108Khz
1PPS signals:1 Hz
10 MHz signals: 10 MHz
Supports a wide range of input amplitudes:
WordClock signals: from 1.25 V to 5 V peak load at 75Ω
1 PPS signals: from 0.75 to 3 V peak load at 50Ω
10MHz signals: from 0.35 to 1.4 V pk-to-pk load at 50Ω
Provides one input and up to eight outputs, with the following:
5 V peak (WordClock) load at 75Ω
3 V peak (1 PPS) load at 50Ω
1.4 V pk-to-pk (10 MHz) load at 50Ω
Fans out AC-Coupled and TTL/CMOS types of signals while the amplifier maintains an end-to-end DC transparency
Provides high impedance/50Ω/75Ω terminated inputs, and 50/75Ω terminated outputs
Supports voltage gain adjustment from -12dB to +6dB
Provides adjustable output levels
Provides card edge control for Gain parameter
Includes built-in basic signal detection and auto-adjusting thresholds when selecting different input signals
Provides a passive loop-through input (when used with WCLK6801+DL) to ease distribution of more than 8 Word Clock signals, by daisy chaining many WCLK6801+ modules
Supports remote control, status monitoring, and error reporting with CCS-P/SNMP control software
Hot-swapping capability
1
2
Back Modules
2
IN
1
4
6
OUT
3
5
8
7
2
IN
LOOP
1
4
6
OUT
3
5
8
7
WCLK6801+D
WCLK6801+DL
Figure 1-1 WCLK6801+D and WCLK6801+WCLK6801+DL Back Modules
Signal Flow
WordClock /
1 PPS / 10 MHz
Input
Receiver
Input Buffer
+6 / -12 dB
Amplifier
Signal
Presence
Detector
Control
Interface
CPU
Control
Figure 1-2.
WCLK6801+ Signal Flow Diagram
Loop (WCLK6801+DL Back Module)
Driver
50Ω 25Ω
Driver
50Ω 25Ω
Driver
50Ω
25Ω
Driver
50Ω
25Ω
Driver
50Ω 25Ω
Driver
50Ω 25Ω
Driver
50Ω 25Ω
Driver
50Ω
25Ω
Out 1
Out 2
Out 3
Out 4
Out 5
WordClock /
1 PPS / 10 MHz
Output
Out 6
Out 7
Out 8
2
Installation and Operation
3
Unpacking the Module
Before you install modules, perform the following:
Check the equipment for any visible damage that may have occurred during transit.
Confirm receipt of all items on the packing list.
Contact your Customer Service representative if parts are missing or damaged.
Remove the anti-static shipping pouch, if present, and all other packaging material.
Retain the original packaging materials for possible re-use.
See “Unpacking/Shipping Information” on page vi for information about returning a
product for servicing.
Setting Jumpers
Prior to power-up, you must set the WCLK6801+ jumpers to the correct configurations. The different jumpers and their settings are described in
On Jumper CJS3, for example (
Figure 2-1 on page 4 ), place the jumper on pins 1 and 2 to
set the module for Remote control, or pins 2 and 3 to set the module for Local control.
The Local setting locks out external control panels and allows card-edge control only; in this position, remote software applications can monitor, but not control the module. The
Remote setting allows either remote or local (card-edge) configuration, operation, and monitoring of the WCLK6801+.
4
CJ3
LOC
REM
CJ3
LOC
REM
Remote Control
(Pins 1 and 2)
Local Control
(Pins 2 and 3)
Figure 2-1 Jumper CJS3 Settings for Remote and Local Control
If you intend to control the gains locally at the card edge, you will need to configure
jumpers J9 and J11 for Gain Value Set (see Table 2-1 on page 5
). This makes it possible to use the card-edge up/down toggle switch to raise or lower the Gain.
Before operating the WCLK6801+ module, ensure that the Input impedance jumper (J10) and the eight Output jumpers (CJ4 to CJ7) are all set to the same value (either 50Ω or
75Ω). This is necessary to configure the input to the WordClock, 1 PPS, or 10 MHz standard. The module will not function if the input and output jumpers are set to different values.
(The default Input impedance is 75Ω for the non-loopthrough version, and Open:
Hi-Z for the loopthrough version. The default Output impedance is 75Ω for both the non-loopthrough and loopthrough versions.)
By placing the jumper J10 in open state, the Input impedance is set to Hi-Z. This mode is used to transfer all of the voltage signal from the source without loss—in other words, it is
voltage bridging: a maximum voltage transfer to the load.
To operate the module, you must also make a selection in the Signal Type parameter that appears in the software control interface, even if you intend to locally control this module.
As shown in
Table 2-1 on page 5 , the Boot Loader Mode uses a combination of the J9
and J11 jumpers. To enter into Boot Loader Mode, set the jumpers as shown in
, and then re-insert the module—while at the same time holding the toggle switch in the up or down position.
See
Figure 2-2 , Figure 2-3 and Figure 2-4
for the locations of the jumpers.
WCLK6801+
Installation and Operation Manual
5
Table 2-1 WCLK6801+ Jumpers
Function
WordClock (default)
1 PPS and 10 MHz
Loopthrough
(default on WCLK6801+DL back module)
Remote/Local Control
Gain Value Set Enabled
Boot Loader Enabled*
Impedance Pins/Jumper
75Ω
50Ω
Input Termination: Short Pins 2 and 3 on Jumper J10
Output Termination: Short Pins 1 and 2, and Pins 3 and 4 of CJ4 to CJ7
(OUT1 to OUT8)
Input Termination: Short Pins 1 and 2 on Jumper J10
Output Termination: Short Pins 1 and 2, and Pins 3 and 4 of CJ4 to CJ7
(OUT1 to OUT8) short for 50
Ω
.
High-Z
--
--
--
Input Termination: Sets all pins to Open on Jumper J10
Output Termination: Short pins as required for WordClock or 1 PPS/10
MHz operation
Remote: Short Pins 1 and 2 on Jumper CJS3 (default)
Local: Short Pins 2 and 3 on Jumper CJS3
Short Pins 1 and 2 on Jumper J9
Short Pins 2 and 3 on Jumper J11
Short Pins 1 and 2 on Jumper J9
Short Pins 1 and 2 on Jumper J11
*To enter the Boot Loader mode, set the jumpers indicated in the table, and then re-insert the module into the frame while holding down (or up) the card-edge toggle switch.
Table 2-2 shows an example of the WordClock input and output voltage amplitudes than
can be expected at 0 dB Gain.
Table 2-2 Example of Output vs. Input Voltage Amplitudes at 0dB Gain for WordClock Application
Voltage
Source
(Zs=75Ω)
1.5 V
Internal Input
Impedance
Setting (Zin)
Terminated
(Zs=Zin)
Input Voltage
(Seen by
WCLK6801+)
WCLK User
Gain
Setting
Output Voltage,
Unterminated
(Zload >> Zout)
1.5 V 0 dB 3 V
Output Voltage,
Terminated
(Zload=Zout)
~
1.5 V
High*
(Zin>>Zs
High
(Zin>>Zs
1.5V
3.0 V
3 V
6 V
~
~
1.5 V
3.0 V
* Assumes that the input impedance has been terminated on one of the other devices in the chain, such that the input impedance remains at 75Ω. Note: Proper termination at input and output is recommended.
6
Gain Value Set and
Boot Loader Mode
Remote/Local
Output Impedance
Input Impedance
Figure 2-2.
Location of WCLK6801+ Jumpers
Remote/Local
Gain Value Set and
Boot Loader Mode
Figure 2-3 Gain Value, Boot Loader, and Remote/Local Jumpers
Input
Impedance
Output
Impedance
Figure 2-4 Impedance Jumpers
WCLK6801+
Installation and Operation Manual
7
Maximum Frame Power Ratings
WCLK6801+ modules operate only in fan-cooled FR6822
+QXFE frames, or FR6822+F frames containing a 6800+ETH module, subject to the limitations shown in
The power consumption of a WCLK6801+ module is 8.4 W in WordClock mode, 1.4 W in
1 PPS mode, and 3.3 W when set to 10 MHz. This maximum power use is dependent on the mode of operation, the output amplitude, and the load. For example, when the signal type is WordClock, the maximum power consumption is 8.4 W when the output signal is
5 V peak, and all the outputs are terminated into 75
Ω
. The module consumes less power in
WordClock mode if the output amplitude is lower and the outputs are not connected—or are set to drive a high impedance load.
Table 2-3 Maximum Allowable Frame Power Ratings
Frame Type
FR6822
+QXFE frame
FR6822+F frame containing a
6800+ETH module
Max. Frame Power
Dissipation
120W
Number of
Usable Slots*
20
*Each WCLK6801+ module requires two slots; a frame can include a maximum of ten WCLK6801+ modules.
Max. Power
Dissipation Per Slot
6 W
CAUTION: To maintain proper temperatures, ensure that the front panel is closed at all times and that the fan module is fully operational.
Installing WCLK6801+ Modules
WCLK6801+ products can be installed in an FR6822
+QXFE frame, or an FR6822+F frame containing a 6800+ETH module. See your Frame Installation and Operation Manual for general information about installing back modules in a frame.
CAUTION: Before installing this product, read the 6800
+ Series Safety Instructions
and Standards Manual available on our website, or on the Harris Infrastructure and
Networking Documentation DVD. This safety manual contains important information about the safe installation and operation of 6800
+ series products.
WCLK6801+ modules require no specialized installation or removal procedures. However, if you are installing both front and rear modules, ensure that the back module is installed first before plugging in the front module.
During removal, ensure that the front module is unplugged from the frame first, before uninstalling the rear module.
8
Upgrading Module Firmware
This module’s firmware can be updated using CCS Navigator version 4.9 or higher, or the
HTTP software upgrade tool. In order to perform these upgrades, the frame must be equipped with a 6800
+ETH module, version 4.8 or higher. See your frame manual for more information.
In the event of a failed upgrade, the Boot Loader mode is enabled using jumpers. See
for details.
Loopthrough Functionality
Loopthrough capability is only available using the WCLK6801+DL back module.
If the loopthrough WCLK6801+DL back module is used in a terminated application, Out 1 should be terminated at the downstream device .
If there is no downstream device, ensure that you terminate the Out 1 port with an external 50Ω terminator (for 10 MHz and 1 PPS), or 75Ω terminator (for WordClock). See
.
For non-terminated applications, both the WCLK6801+ and the downstream device should be set to Open (High-Z) input.
WCLK6801+
Installation and Operation Manual
9
Downstream Device
Terminated Applications
WCLK6801+DL
2
WCLK IN
LOOP
1
If a downstream device is connected, output 1 termination should be located at the downstream device.
Jumper J10 is set to Open (High-Z).
4
3
WCLK OUT
6 5
8
7
WCLK6801+DL
2
WCLK IN
LOOP
1
4 3
WCLK OUT
6
5
8
7
If The WCLK6801+ is not connected to a downstream device, output1 should be terminated by an external terminator.
Jumper J10 is set to Open (High-Z).
No Downstream Device
Non-Terminated Application
WCLK6801+DL
2
WCLK IN
LOOP
1
Jumper J10 set to
High -Z (open)
4 3
Note: To maintain good signal integrity, a matching load termination is recommended.
WCLK OUT
6
5
8
7
High -Z
(open)
Figure 2-5.
Loopthrough Terminated and Non-Terminated Applications
Downstream Device
10
Changing Parameter Settings
All parameters can be controlled or viewed using control software. However, only the Gain control can be operated at the card edge.
Using CCS Software
Before using CCS Navigator to change your module’s parameter settings, you must discover the module.
To discover the module, your Navigator software must be in Build mode.
1
If the Discovery window is not open, click Tools > Discovery in the main menu.
A Discovery window opens, most likely in the bottom left corner of the screen.
2
Click Options, and then click Add.
3
Enter the IP address of the frame that contains your module, or the frame that contains a
6800
+ETH module that provides access to your module.
4
Click OK to close the Add Host dialog box, and then click OK again to close the Discovery
Options dialog box.
5
Click Start.
This triggers Navigator to run a discovery. When the discovery finishes, Discovery
Completed is displayed in the Discovery pane.
6
Click Save to save the results of your discovery to the Discovery folder of the Navigation pane.
7
Switch to Control mode by selecting Operational Mode > Control from the main menu.
8
Double-click WCLK6801+ in the Navigation pane.
The Control window opens, displaying the module’s controls.
You can now switch to Control mode by selecting Operational Mode > Control from the main menu. Double-click WCLK6801+ in the Navigation pane. The Control dialog box opens, displaying the module’s controls.
Reading Software and Hardware Versions
The current software version of your module can viewed using an HTTP browser, CCS
Navigator, or a CCS-enabled control panel.
Control Parameters
Table 2-4 lists all of the available parameters and options for the WCLK6801+. All
parameters clip unless otherwise indicated. Although all parameters can be controlled or viewed using control software, only the Gain control can be operated at the card edge. A waveform monitor, vectorscope, or other monitoring device is required to check the Gain
output levels when using card-edge controls (see Table 2-5).
WCLK6801+
Installation and Operation Manual
11
To use the Gain control locally, you must enable the Gain Value Set, using the J9 (CTRL1) and J11 (CTRL2) jumpers. See
Note: If the actual input signal is not the same as the option you selected in the Input Type parameter, the signal is passed through to the output, but the Signal Presence parameter may—or may not—display No Signal. In this condition, the Gain control continues to amplify or reduce the output levels, depending on the user setting.
When setting the control parameters on the WCLK6801+, the effect is immediate.
However, the module requires 30 seconds to save the latest change. After 30 seconds, the new settings are saved and will be restored if the module loses power and must be restarted.
Table 2-4 WCLK6801+ Parameters
Parameter
Serial Number [RO]
Input Type
Description
Displays the WCLK6801+ serial number
Selects the type of input signal
Signal Presence
[RO]
Gain (dB)
Detects the presence of an input signal
Adjusts the gain of the output signal
Value
--
WordClock
1 PPS
10 MHz
Yes
No
-12 dB to +6 dB
Table 2-5 Characteristics of Signals
Signal Type
10 MHz
1 PPS
Impedance
50 Ω
Frequency
1 Hz
32-108 KHz
Waveform
Square pulse
Square wave
Default
--
WordClock
--
0 dB
12
LEDs and Alarms
Figure 2-6 shows the location of the Input Signal Present monitoring LED on the front
module.
Status LED
Signal Presence
LED
Figure 2-6 Location of Card-Edge LEDs
The WCLK6801+ module does not have any card-edge alarms. Instead, a module status
LED on the corner of the module lights up if an error is detected.
Table 2-6 Module Status LED Descriptions
LED Color
Off
Green
Red
Meaning
There is no power to the module; the module is not operational.
There is power to the module; the module is operating properly.
The module detects an alarm condition.
The WCLK6801+ detects only one alarm condition: loss of input signal.
Table 2-7 Alarm Description
Alarm Name
Loss of Signal
Priority
6
Trigger Time
(Seconds)
1
Clear Time
(Seconds)
2
3
Specifications
Signal Input
Table 3-1 WCLK6801+ Signal Input Specifications
Item
Number of Connectors
Specification
1
Standards
WordClock, 1 PPS,10 MHz
Back Module Connector
Type
Impedance
BNC
Bandwidth
Input Amplitude
Hi-Z
75Ω (WordClock)
50Ω (1 PPS,10 MHz
±
1%, jumper-selectable)
32-108Khz (WordClock)
1 Hz (1 PPS)
10 MHz (10 MHz)
WordClock signals: from 1.25 V to 5 V peak into a 75Ω load
1 PPS signals: from 0.75 V to 3 V peak into a 50Ω load
10MHz signals: from 0.35 V to 1.4 V pk-to-pk into a 50Ω load
13
14
Signal Output
Table 3-2 WCLK6801+ Signal Output Specifications
Item
Number of Outputs
Back Module Connector Type
Standards
Bandwidth
Impedance
Maximum Output Voltage
Specification
8 (non looping WCLK6801+D back module)
7 (looping WCLK6801+DL back module)
BNC
WordClock, 1 PPS,10 MHz
32-108Khz (WordClock)
1 Hz (1 PPS)
10 MHz (10 MHz)
75Ω (WordClock)
50Ω (1 PPS,10 MHz
±
1%, jumper-selectable)
5 V peak (WordClock) into a 75Ω load
3 V peak (1 PPS) into a 50Ω load
1.4 V pk-to-pk (10 MHz) into a 50Ω load
Power Consumption
The power consumption of this module is dependent on the mode of operation, the output
amplitude, and the load. See page 7
for details.
Table 3-3 Power Consumption Specifications
Module Signal Type
WordClock
1PPS
10M
Maximum Power Consumption
8.4 W
1.4 W
3.3 W
Propagation Delays
Table 3-4 Propagation Delay Specifications
Item
10 MHz Signal
1 PPS Signal
WordClock 32 KHz Signal
WordClock 108 KHz Signal
* Accuracy ±1ns
Specification*
54 ns
52 ns
50 ns
54 ns
A
Communication and Control
Troubleshooting Tips
15
Software Communication Problems
Problem
The frame is powered up, but the module does not communicate with CCS Navigator or the web GUI interface.
Solutions
Ensure you have specified the proper module slot.
See your 6800
+ Frame Installation and Operation Manual for more information about slot identification.
Confirm there is an 6800
+ETH module installed in the frame.
Remove any legacy 6800 series product that is in the frame.
CCS software cannot communicate with legacy 6800 series products, even if these modules may operate with card-edge controls in the frame. Legacy 6800 products do not have the “
+” symbol on their extractor handles.
Check for damaged pins on the back module by following this procedure:
i.
Unplug the front module.
ii.
Unscrew and remove the back module.
iii. Inspect the 20- or 30-pin spring connector at the bottom of the back module, and verify that the connector does not have any slightly bent, or severely depressed pins.
iv. Carefully reposition any bent or depressed pins. If this is not possible, contact Harris
Customer Support.
Figure A-1 Typical Back Module Spring Connector
16
Problem
The IP address of the frame has been forgotten.
Solution
Follow this procedure:
1
Remove the ETH6800
+ module from the frame.
2
Select DIP switch 2 on the ETH6800
+ module and slide the tab to the forward position.
This sets the ETH6800
+ module to its default IP address of 192.168.100.250.
Slide this DIP switch tab forward for default IP address
Figure A-2 ETH6800
+ DIP Switch
3
Use CCS Navigator or the web browser to interface with the ETH6800
+ module and then set the desired IP address.
4
Set the DIP switch back to its normal position and then re-insert the module.
Problem
There is no Ethernet connectivity with the frame.
Solutions
Verify that the correct IP address is being used. If your are not certain, refer to the above procedure to set to default IP.
Verify that the ethernet cable is the correct type (a crossover cable is required for direct connection from a PC).
Verify the Link and Activity (left and right) status LEDS are active on the RJ-45 connector at the rear of the frame.
Verify the Status LED is lit and green on the ETH6800+ card, as viewed from the front of the frame with the door open.
Verify that the security settings on the PC allow for connection to a frame (TCP port 80 and UDP ports 4000/4050 must be open).
Verify that the PC is configured for and can communicate on the desired subnet.
Verify that the frame reference signal has not been mistakenly connected to a
Communications port on the rear of the frame.
WCLK6801+
Installation and Operation Manual
17
Problem
CCS software sees the frame, but does not find all of the modules.
Solutions
Remove any legacy 6800 series products.
Plug your modules in before starting the discovery.
Start your discovery after the frame and all modules have fully powered up.
Refresh the CCS software and ensure that the installed modules are fully powered up first before discovery.
Problem
CCS Software does not respond after it is launched.
Solutions
Close any CCS software that is already launched.
Problem
CCS software shows a module in the Control window, but cannot control it.
Solution
Follow this procedure:
1
Set the module’s Local/Remote jumper to Remote.
2
Ensure the module name in the Control window matches the module type in the frame.
3
Gently push the module into its slot in the frame to ensure it is seated properly and powered up.
4
Verify that the Control window indicates the device is ready.
Hardware Communication Problems
Problem
After a power failure, the frames and PC do not communicate.
Solution
Follow this procedure:
1
Wait four minutes for the frames to recover from the power failure.
2
Close the CCS software, and then restart the PC.
3
Restart the software application.
18
Problem
The module does not seem to work.
Solutions
Ensure the correct frame is powered up.
Verify that all appropriate rear connections are secure.
Gently push the module into its slot in the frame to ensure it is seated properly. Then verify the Status LED on the module is lit and green.
Ensure the back module does not have any slightly bent, or severely depressed pins.
F ollow this procedure:
i.
Unplug the front module.
ii.
Unscrew and remove the back module.
iii. Carefully reposition any slightly bent, or severely depressed pins. If this is not possible, contact Customer Support.
Index
A
B
C
Changing parameter settings 10
D
F
G
–
H
I
J
–
L
–
M
O
P
–
Propagation delay specifications 14
R
S
Safety precautions, general viii
–
Specifications
T
U
,
V
19
Scarica
Link pubblico aggiornato
Il link pubblico alla tua chat è stato aggiornato. Puoi visualizzare e gestire i tuoi link di chat dopo la registrazione qui.
Link pubblico del documento
Pubblicità
