HearthRite HR20EN-1 Owners Manual and Installation Manual


Add to my manuals
24 Pages

advertisement

HearthRite HR20EN-1 Owners Manual and Installation Manual | Manualzz
 HearthRite
INFRARED VENT-FREE
NATURAL GAS
SPACE HEATER
OWNER S OPERATION AND INSTALLATION MANUAL
HR20EN-1 HR30EN-1
A WARNING: Improper installation,
adjustment, alteration, service or main-
tenance can cause injury or property
damage. Refer to this manual for correct
installation and operational procedures.
For assistance or additional information
consult a qualified installer, service agency,
or gas supplier.
AWARNING: This is an unvented gas-
fired heater. It uses air (oxygen) from the
room in which it is installed. Provisions
for adequate combustion and ventilation
air must be provided. Refer to Air For
Combustion and Ventilation section on
page 5 of this manual.
HearthRite
A Division of Empire Comfort Systems, Inc.
918 Freeburg Avenue
Belleville, IL 62220
Phone : 618-233-7420 or 1-800-851-3153
Fax : 618-233-7097 or 1-800-443-8648
www.hearthrite.com
A WARNING: If the information in
this manual is not followed exactly, a
fire or explosion may result causing
property damage, personal injury, or loss
of life.
Do not store, or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS
e Do not try to light any appliance.
e Do not touch any electrical switch; do not
use any phone in your building.
e Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
e If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed by a
qualified installer, service agency or gas
supplier.
This appliance may be installed in an
aftermarket* permanently located, manufac-
tured (mobile) home, where not prohib-
ited by local codes.
This appliance is only for use with the
type of gas indicated on the rating plate.
This appliance is not convertible for use
with other gases.
WATER VAPOR: ABY-PRODUCT OF UNVENTED ROOM
HEATERS
Water vapor is a by-product of gas combustion.An
unvented room heater produces approximately one (1)
ounce (30ml) of water for every 1,000 BTU’s
(.3KW”s) of gas input per hour. Refer to page 4.
*Aftermarket: Completion of sale, not for purpose of
resale, from the manufacturer.
INSTALLER: Leave this manual with the appli-
ance
CONSUMER: Retain this manual for future refer-
ence
HR-MCL051-01E-0507
Table of Contents
SATCLY INMTOMMATION 7100 cs cvorensavanea poucrssese ss aaesvrecuanarednranpes Area a 2
Product CFeattres i rte cea al A 3
| Deal COS rrr rer eT rE Te Ee vs ws ETE Rese SE Se A CA nn... 3
LN DE CAINE ee oc wm wm vnc me er 4
Air for Combustion and Ventilation.......…..….….…........ssesseserrn cran cran nca nn en 5
InstallatioNn..…..............eccscereeecer ee rer eee rene ana nan an ana na eaa ana nan aa nana aa een nana eeos 7
Gannecting lo Gas Supply: :-.=.=— enanos ro NAAA ea aa somos 9
Checking Gas ConneCtiON Sasse ere eae ae 10
Operating, U Sa a aaa Rae: cea. eee NA sary 11
Cleaning 8% MaintenancCe.....................0000veci 0 e RN ER RR RI IR II II II IR GIRAR 14
Replacement Parts. cocoa 16
SO PECHICAHONS. ov ov sams wnsis soa assay sues swims wes 555 CNAE ea as ME 16
Troubleshootingya. 2 .0.. er ee 17
op oo pds a TRA I I rE TT 20
warranty INTOTNRIOÓN ..———— ..——— entra aa Ne E A ст 24
SAFETY INFORMATION
Make certain you read and under-
stand all warnings. Keep this
manual for reference. It is your
guide to safe and proper operation
of this heater.
A IMPORTANT: Read this
owner's manual carefully and
completely before trying to
assemble, operate, or service
this heater. Improper use of
this heater can cause serious
injury or death from burns,
fire, explosion, electrical
shock, and carbon monoxide
poisoning.
A DANGER: Carbon monoxide
poisoning may lead to death!
WARNING
When used without fresh air, heater
may give off CARBON MONOXIDE, an
odorless, poisonous gas.
DO NOT INSTALL HEATER UNTIL
ALL NECESSARY PROVISIONS ARE
MADE FOR COMBUSTION AND VEN-
TILATION AIR. CONSULT THE WRIT-
TEN INSTRUCTIONS PROVIDED
WITH THE HEATER FOR INFOR-
MATION CONCERNING COMBUS-
TION AND VENTILATION AIR. IN THE
ABSENCE OF INSTRUCTIONS,
REFER TO THE NATIONAL FUEL
GAS CODE. ANSI 2223. 1. SEC-
TION 5.3 OR APPLICABLE LOCAL
CODES.
This heater is equipped with a PILOT
LIGHT SAFETY SYSTEM designed to
turn off the heater if not enough fresh air
is available
SAFETY SYSTEM!
DO NOT TAMPER WITH PILOT LIGHT
If heater shuts off, do not relight until
you provide fresh air.
[CARBON MONOXIDE POISONING
MAY LEAD TO DEATH!
Early signs of carbon monoxide poi-
soning resemble the flu with
headache, dizziness and/or nausea.
If you have these signs, heater may
not be working properly. Get fresh air
at once! Have heater serviced.Some
people - pregnant women, persons
with heart or lung disease, anemia,
those under the influence of alcohol,
those at high altitude - are more af-
fected by carbon monoxide than
others.
WARNING
Natural Gas: Natural gas is
odorless. An odor-making agent
is added to natural gas. The
odor helps you detect a natural
gas leak . However, the odor
added to natural gas can fade.
Natural gas may be present
even though no odor exists.
If heater keeps shutting off have it ser-
viced . Keep burner and control com-
partment clean.
SAFETY INFORMATION
4 WARNING: Do not use any
accessory not approved for
use with this heater.
WARNING: Any change to
lts controls can
A
this heater or
|be dangerous.
WARNING
Models HR20EN-1 , HR30EN-1 are
equipped for natural gas. Field
conversion is not permitted.
Due to high temperatures, heater
should be kept out of
traffic and away from furniture
and draperies.
Front surface of heater becomes
very hot when operating heater.
Keep children and adults away
from hot surface to avoid burns
or clothing ignition. Heater will
remain hot for atime after shut
down. Allow surface to cool
before touching.
Do not place clothing or other
flammable material on or near
the appliance. Never place any
objects on the heater.
Carefully supervise young
children when they are in the
same room with heater.
Make sure grill guard is in
place before operating the heater.
Keep the appliance area clear
and free from combustible
materials, gasoline, and other
flammable vapors and liquids.
1. This appliance is only for use
with the type of gas indicated
on the rating plate. This
appliance is not convertible for
use with other gases.
2. If you smell gas
e Shut off gas supply.
e Do not try to light any appliance.
e Do not touch any electrical
switch, do not use any phone in
your building.
e Immediately call your gas
supplier from a neighbor's
phone. Follow the gas
suppliers instructions.
e |f you cannot reach your gas
supplier, call the fire department.
3. This heater shall not be
installed in a bedroom or
bathroom
4. This heater needs fresh,
air to run properly.
This heater has an
Oxygen Depletion Sensor
(ODS) safety shutoff system.
The ODS shuts down the
heater if not enough fresh air
is available. See Fresh Air for
Combustion and Ventilation
pages 5 and 6.
5. Keep all air openings in front
and bottom of heater clear
and free of debris. This will
insure enough air for proper
combustion.
6. If heater shuts off. Do not
relight until you provide fresh,
outside air. If heater keeps
shutting off, have it serviced.
7. Do not operate
e Where flammable liquids or
vapors are used or stored
® Under dusty conditions
8. Before using furniture polish,
wax, carpet cleaner, or similar
products, turn heater off. If
heated, the vapors from these
products may create a white
powder residue within burner
box or on adjacent walls or
furniture.
9. Do not use heater if any part
has been under water.
Immediately call a qualified
service technician to inspect
the room heater and to replace
any part of the control system
and any gas control which has
been under water.
Turn off heater and let cool
before servicing. Only a qualified
service person should service
and repair heater.
11. Operating heater above
elevations of 4,500 feet could
cause pilot outage.
PRODUCT FEATURES
(see figure1,page 4)
SAFETY PILOT
This heater has a pilot with an
Oxygen Depletion Sensor(ODS)
safety shutoff system. The ODS/
10.
3
pilot shuts off the heater if there is
not enough fresh air.
AUTOMATIC IGNITION
SYSTEM
This heater is equipped with an
automatic control system.
This system requires no matches
to light heater.
TOUCH PAD THERMO-
STATIC HEAT CONTROL
This heater has a control module
with a thermostat sensing bulb.
Set desired temperature with touch
pad . This results in the greatest
heater comfort and may result in
lower gas bills.
MANUAL OVERRIDE
CONTROL SYSTEM
(HR20EN-1, HR30EN-1)
There are two control systems,
electric and manual override.
If no electric power is available,
you can operate heater by
manual override.
LOCAL CODES
This heater is designed for vent-free
operation. Some state and local
codes prohibit the use of vent-free
heater.
QUALIFIED
AGENCY
Installation and replacement of gas
piping, gas utilization equipment or
accessories and repair and servic-
ing of equipment shall be per-
formed only by a qualified agency.
The term “qualified” agency means
any individual,firm,corporation,or
company that either in in person or
through a representative is engaged
in and is responsible for (a) the
installation, testing, or replacement
of gas piping or(b) the connection
installation, testing, repair, or servic-
ing of equipment; that is experienced
in such work; that is familiar with all
precautions required, and that has
complied with all the requirements
INSTALLING
of the authority having jurisdiction .
PRODUCT FEATURES
Touch, Pad
ON/OFF Switch
Burner
4 E |
Cuore I |
ORTA LO: y
Lower Front Panel
Safety Pilot
sera Ne Top
| Grill Guard
TA
e
tv y
LA Ignitor for Manual Override Control
a System
naa
ontrol Knob for Manual Override
Control System
Figure1 Vent-Free Heater
LOCAL CODES CONTINUED
Install and use heater with care. Follow all local
codes. In the absence of local codes, use the
latest edition of National Fuel Gas code ANSI
2223.1, also known as NFPA 54%.
*Available from :
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
State of Massachusetts : The installation must be
made by a licensed plumber or gas fitter in the Com-
monwealth of Massachusetts.
Sellers of unvented propane or natural gas-fired
supplemental room heaters shall provide to each
purchaser a copy of 527 CMR30 upon sale of the
unit.
In the State of Massachusetts, unvented propane and
natural gas-fired space heaters shall be prohibited
in bedrooms and bathrooms.
UNPACKING
1. Remove heater from carton.
2. Remove all protective packaging applied to
heater for shipment.
. Check heater for any shipping damage. If heater
is damaged, promptly inform dealer where you
bought heater.
WATER VAPOR: A BY-PRODUCT OF VENT-FREE ROOM HEATERS
Water vapor is a by-product of gas combustion. A vent-
free room heater produces approximately one (1) ounce
(30ml) of water for every 1,000 BTU's (.3KW's) of gas
input per hour.
Unvented room heaters are intended for supplemental
heat (a room) rather than a primary heat source (an entire
house). In most supplemental heat applications, the
water vapor does not create a problem. In most
applications, the water vapor enhances the low humidity
atmosphere experienced during cold weather.
The following steps will help insure that water vapor does
not become a problem.
1. Be sure the heater is sized properly for the application,
including ample combustion and ventilation air.
2. If high humidity is experienced, a dehumidifier
may be used to help lower the water vapor content
of the air.
3. Do not use a vent-free room heater as the primary
heat source.
A IMPORTANT: Vent-free heaters add mois-
ture to the air. Although this is beneficial,
installing heater in rooms without enough
ventilation air may cause mildew to form from
too much moisture. See Fresh Air for Combus-
tion and Ventilation, pages 5 and 6.
AIR FOR COMBUSTION
AND VENTILATION
Á WARNING: This heater shall
not be installed in a confined
space or unusually tight con-
struction unless provisions are
provided for adequate combus-
tion and ventilation air. Read the
following instructions to insure
proper fresh air for this and other
fuel-burning appliances in your
home.
PROVIDING ADEQUATE
VENTILATION
The following are excerpts from
National Fuel Gas Code. NFPA
54/ANSI Z223.1, Section 5.3. Air
for Combustion and Ventilation.
All spaces in homes fall into one
of the three following ventilation
classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space
The information on pages 5
through 6 will help you classify
your space and provide adequate
ventilation.
LengthXWidthxHeight=
to the total volume of the space.
Unusually Tight Construction
The air that leaks around doors and
windows may provide enough fresh
air for combustion and ventilation.
However, in buildings of unusually
tight construction, you must provide
additional fresh air.
Unusually tight construction is
defined as construction where:
a. Walls and ceilings exposed to
the outside atmosphere have a
continuous water vapor retarder
with a rating of one perm (6x10 kg
per pa-sec-m? or less with
openings gasketed or sealed and
b. Weather stripping has been
added on openable windows and
doors and
c. Caulking or sealants are applied
to areas such as joints around
window and door frames, between
sole plates and floors, between
wall-ceiling joints, between wall
panels, at penetrations for plumbing,
electrical, and gas lines, and at
other openings. If your home meets
all of the three criteria above, you
must provide additional fresh air.
See Ventilation Air From Outdoors,
page 6.
If your home does not meet all of
the three criteria above, see
Determining Fresh-Air Flow for
Heater Location, page 5.
cu.ft. (volume of space)
Confined and
Unconfined Space
The National Fuel Gas Code ANSI
2223.1 defines a confined space as
a space whose volume is less than
50 cubic feet per 1,000 Btu per hour
(4.8 m* per kw) of the aggregate
input rating of all appliances in-
stalled in that space and an uncon-
fined space as a space whose
volume is not less than 50 cubic
feet per 1,000 Btu per hour (4.8 m*
per kw) of the aggregate input
rating of all appliances installed in
that space. Rooms communicating
directly with the space in which the
appliances are installed*, through
openings not furnished with doors,
are considered a part of the uncon-
fined space.
This heater shall not be installed
in a confined space or unusually
tight construction unless provisions
are provided for adequate combus-
tion and ventilation air.
* Adjoining rooms are communi-
cating only if there are doorless
passageways or ventilation grills
between them.
DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION
Determining if you have a Confined or Unconfined Space*
Use this worksheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways
or ventilation grills between the rooms.
1. Determine the volume of the space (lengthxwidthxheight).
Example: Space size20ft. (length)x16ft.( width)x8ft. (ceiling height)=2560cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms
2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.
(volume of space) 50 cu. ft.=(Maximum Btu/Hr the space can support)
Example: 2560 cu. ft. (volume of space)+50 cu.ft.=51.2 or 51.200(maximum Btu/Hr the space can support)
3. Add the Btu/Hr of all fuel burning appliances in the space.
Vent-free heater Btu/Hr
Gas water heater* Btu/Hr Example:
Gas fumace Btu/Hr Gas water heater 40,000 Btu/Hr
Vented gas heater Btu/Hr Vent free heater + 18,000 Btu/Hr
Gas Fireplace logs Btu/Hr Total - 58,000 Btu/Hr
Other gas appliances* + Btu/Hr
Total = Btu/Hr
*Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and
vents to the outdoors.
4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.
Btu/Hr (maximum the space can support)
Btu/Hr (actual amount of Btu/Hr used)
Example : 51,200 Btu/Hr(maximum the space can support)
58,000 Btu/Hr(actual amount of Btu/Hr used)
The space in the above example is a confined space because the actual Btu/Hr used is more than the
maximum Btu/Hr the space can support.
You must provide additional fresh air. Your options are as follows:
A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined
space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air From
Inside Building.
B. Vent room directly to the outdoors. See Ventilation Air From Outdoors.
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an
unconfined space. You will need no additional fresh air ventilation.
NOTE: If the area in which the heater may be operated is smaller than that defined as an unconfined space
or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one
of the methods described in the National Fuel Gas Code, ANSI Z223.1, Section 5.3 or applicable local codes.
Ventilation Air From Inside Building >
This fresh air would come from an adjoining a TUES
unconfined space. When ventilating to an adjoin- 7] | entiation Gils
Or into adjoining Room,
ing unconfined space, you must provide two per- Veces | JET НЕЕ
. т i 1 a АСТ
manent openings: one within 12" of the ceiling and oom.
Room, Room,
one within 12" of the floor on the wall connecting =| =
the two spaces (see options 1 and 2, Figure 2). You | = SZ
can also remove door into adjoining room (see Mar ==
option 3, Figure 2). Follow the National Fuel Gas Y
Code NFPA 54/ANSI Z223.1. Section 5.3, Air for
Combustion and Ventilation for required
size of ventilation grills or ducts. Figure 2 -Ventilation Air from Inside Building
Ventilation Air From Outdoors N
Provide extra fresh air by using ventilation grills or " oe устан Ш
ducts: You must provide two permanent openings: LL 25, ESA
one within 12" of the ceiling and one within 12" of Outet | =
the floor.
Connect these items directly to the outdoors or | bude
spaces open to the outdoors. These spaces include | = Space
attics and craw! spaces. Follow the National Fuel mel - | =
Gas Code NFPA 54/ANSI Z223.1, Section 5.3. Air for SE «ны Е "О ЕЕ)
Combustion and Ventilation for required size of
ventilation grills or ducts.
== Crawl Space |
IMPORTANT: Do not provide openings for inlet or Rework worksheet, adding the space of the adjoining
— -_— Ma — ——
Figure 3 -Ventilation Air from Outdoors
outlet air into attic if attic has a thermostat-con- unconfined space. The combined spaces must have
trolled power ventj, Heated air entering the attic will enough fresh air to supply all appliances in both
activate the power vent. spaces.
INSTALLATION
A\ NOTICE: This heater is in-
tended for use as supplemental
heat. Use this heater along with
your primary heating system. Do
not install this heater as your
primary heat source. If you have a
central heating system, you may
run system’s circulating blower
while using heater. This will help
circulate the heat throughout the
house.
WARNING: A qualified service
person must install heater. Fol-
low all local codes.
AWARNING: Electrical Grounding
Instructions
This appliance is equipped with a
three-prong (grounding) plug for
your protection against shock haz-
ard and should be plugged directly
into a properly grounded three-
prong receptacie
A\ WARNING: Never install
the heater
® in a bedroom or bathroom.
e in a recreational vehicle.
® where curtains, furniture,
clothing, or other flammable
objects are less than 36 inches
from the front, top, or sides
of the heater.
® as a fireplace insert.
® in high traffic areas.
e in windy or drafty areas.
A WARNING: Maintain the mini-
mum clearances shown in Fig-
ure 4. If you can, provide greater
clearances from floor, ceiling,
and adjoining wall.
CAUTION: If you install the
heater in a home garage
e heater pilot and burner must
be at least 18 inches above
floor.
e locate heater where moving
vehicle will not hit it.
CAUTION: This heater creates
warm air currents. These currents
move heat to wall surfaces next
to heater. Installing heater next to
vinyl or cloth wall coverings or
operating heater where impuri-
ties (such as tobacco smoke, aro-
matic candles, cleaning fluids,
oil or kerosene lamps, etc.) in the
air exist may discolor walls.
CHECK GASTYPE
Use only Natural gas. If your gas
supply is not Natural, do not install
heater. Call dealer where you
bought heater for proper type heater.
LOCATING HEATER
This heater is designed for mount-
ing on a wall, set on floor, away
from a wall. Purchase optional floor
mounting stand from your dealer.
See Accessories, page 16.
For convenience and efficiency,
install heater
e Where there is easy access for
operation, inspection, and service
in coldest part of room.
CEILING
|
| 36"
| Minimum
À
Minimum a = |
From | =
| Sides of
Heater
— 7]
2" Minimum to Top Surface of Carpeting,
Tile, or Other Combustible Material
FLOOR
Figure 4 -Mounting Clearances As
Viewed From Front Of Heater
FASTENING HEATER TO WALL
Mounting Bracket
The mounting bracket is located
on back panel of heater (see
Figure 5). It has been taped there
for shipping. Remove mounting
bracket from back panel.
Mounting Bracket
Figure 5 -Mounting Bracket
Location
INSTALLATION
CONTINUED
Methods For Attaching Mounting
Bracket To Wall
Only use last hole on each end
of mounting bracket to attach
bracket to wall. These two holes
are 16 1/2 inches apart from their
centers. Attach mounting bracket
to wall only in one of two ways:
1. Attaching to wall stud
2. Attaching to wall anchor
Note: Wall anchors, mounting
screws, and spacers are in
hardware package. The hardware
package is provided with heater.
Attaching to Wall Stud: This method
provides the strongest hold. Insert
mounting screws through mounting
bracket and into wall studs.
Attaching to Wall Anchor: This
method allows you to attach
mounting bracket to hollow walls
(wall areas between studs) or to
solid walls (concrete or masonry).
Decide which method better
suits your needs. Either method
will provide a secure hold for the
mounting bracket.
Marking Screw Locations
1. Tape mounting bracket to wall
where heater will be located.
Make sure mounting bracket is
level.
A WARNING: Maintain mini-
mum clearances shown in Figure
6. If you can, provide greater clear-
ances from floor and adjoining wall.
2. Mark screw locations on wall.
(see Figure 6)
Note: Only mark last hole on
each end of mounting bracket.
Insert mounting screws through
these holes only.
3. Remove tape and mounting
bracket from wall.
9 7/8
Min k
У т
Only Insert Mounting
Screws Through
Last Hole On Each
End
ТУ
Min,
Adjoining Wall
Floor
Model HR20EN-1
12 516" 18 12"
pu Min. | |
= я
Rie didi
Г Only Insert Mounting т
= Screws Through Min
= Last Hole On Each
End
27 Floor
Model HR30EN-1
Figure 6 - Mounting Bracket
Clearances
Attaching to Wall Stud Method For
attaching mounting bracket to wall
studs
1. Drill holes at marked locations
using 9/64" drill bit.
2. Place mounting bracket onto
wall. Line up last hole on each
end of bracket with holes drilled
in wall.
3. Insert mounting screws through
bracket and into wall studs.
4. Tighten screws until mounting
bracket is firmly fastened to
wall studs.
Attaching to Wall Anchor Method
For attaching mounting bracket to
hollow walls (wall areas between
studs) or solid walls (concrete or
masonry)
1. Drill holes at marked locations
using 5/16" drill bit. For solid
walls (concrete or masonry), drill
at least 1" deep.
2. Fold wall anchor as shown in
Figure 7 below.
Figure 7- Folding Anchor
3. Insert wall anchor (wings
first) into hole. Tap anchor
flush to wall.
4. For thin walls (1/2" or less),
insert red key into wall
anchor. Push red key to
"nop" open anchor wings
(see Figure 8). —
A IMPORTANT: Do not
hammer key! For thick walls
(over 1/2" thick) or solid walls,
do not pop open wings.
Figure 8 - Popping Open Anchor
Wing For Thin Walls
5. Place mounting bracket onto
wall. Line up last hole on
each end of bracket with wall
anchors.
6. Insert mounting screws through
bracket and into wall anchors.
7. Tighten screws until mounting
bracket is firmly fastened to wall.
Placing Heater on Mounting
Bracket
1. Locate two horizontal
back panel
Figure 9).
2. Place heater onto mounting
bracket. Slide horizontal slots
onto stand-out tabs on
mounting bracket.
slots on
of heater (see
Horizontal slots
Mounting Bracket
Stand-Out Tab (attached to wall)
Figure 9 - Mounting Heater Onto
Mounting Bracket
INSTALLATION
CONTINUED
Installing Bottom Bracket
(See Figure 10)
1. Install bottom bracket to heater
bottom with two screws. It may
be more convenient to remove
heater from wall mounting bracket
to attach bottom bracket.
2. Place heater on mounting bracket.
3. Locate two bottom mounting
holes on wall. These holes are
near bottom on heater.
E A Bottom Bracket
Figure 10 - Installing Bottom Bracket
4. Mark screw locations on wall.
5. Remove heater from mounting
CONNECTING TO GAS
SUPPLY
4h WARNING: A qualified service
person must connect heater to
gas supply. Follow all local codes.
4h WARNING: This appliance re-
quires a 3/8" NPT (Nominal Pipe
Thread) inlet connection to the
pressure regulator.
4h WARNING: Do not overtighten
gas connections.
4h WARNING: Never connect
heater to private ( non-utility )
gas well. This gas is commonly
known as well-head gas.
AA CAUTION: Use only new, black
iron orsteel pipe. Internally-tinned
copper tubing may be used in
certain areas. Check your local
codes. Use pipe of large enough
diameter to allow proper gas volume
to heater. If pipe is too small,
undue loss of pressure will occur.
AA CAUTION: Use pipe joint
sealant that is resistant to
natural gas.
bracket.
. If installing bottom mounting
screws into hollow or solid wall,
install wall anchors. Follow steps
1 through 4 under Attaching
To Wall Anchor Method. If
installing bottom mounting screw
into wall stud, drill holes at marked
locations using 9/64" drill bit.
Replace heater onto mounting
bracket.
. Tighten both screws until heater
is firmly secured to wall. Do not
overtighten.
AA CAUTION: Avoid damage to
regulator. Hold gas regulator with
wrench when connecting to gas
piping and/or fittings.
INSTALLATION NEEDS
Before installing heater, make sure
you have the items listed below.
e piping (check local codes)
® sealant (resistant to Natural
gas)
equipment shutoff valve*
ground joint union
test gauge connection”
sediment trap
tee joint
pipe wrench
*A CSA/AGA design-certified equip-
ment shutoff valve with 1/8" NPT
tap is an acceptable alternative to
test gauge connection.
IMPORTANT : Check your gas
line pressure before connecting
heater to gas line.Gas line pres-
sure must be no greater than10.5
inches of water.lf gas line pres-
sure is higher,heater regulator
damage could occur.
Gas Meter
Figure 11- Gas Meter
Typical Inlet Pipe Diameters
All models up to 20,000 BTU's use
3/8” or greater pipe;
All models 30,000 BTU's and higher,
use 1/2” or greater pipe.Installation
must include an equipment shutoff
valve, union, and plugged 1/8" NPT
tap. Locate NPT tap within reach for
test gauge hook up. NPT tap must be
upstream from heater(see Figure 12).
Pressure
Regulator — AN
5 NBT
_ Pipe Nipple
Heater - rs и ame
Cabinet | - Lea" MO
\ | es нее” ==
‘2 | — Gr
| = Ground Joint
== | ET Union
r Tee em Xx |
Test Reducer ce т tt A Equipment
Gauge Bushing to — > rer
Connection* | 1/8" NPT > A alve
" D Inlet Pipe From Gas
_1/8"NPT — ) 2] Meter (7"W.C. to
Plug Tap Г f= 10.5"W.C.Pressure)
JW
Tee Joint — ET
Sediment | | . |
| Cap —
Figure 12 -Gas Connection
—
*A CSA/AGA design-certified equipment shutoff valve with 1/8” NPT tap
is an acceptable alternative to test gauge connection. Purchase the
optional CSA/AGA design-certified equipment shutoff valve from
your dealer.
In the state of Massachusetts the gas
cock must be a T handle type. The
state of Massachusetts requires that
a flexible appliance connector cannot
exceed three feet in length .
IMPORTANT: Install an equipment
shutoff valve in an accessible
location. The equipment shutoff
valve is for turning on or shutting
off the gas to the appliance.
Apply pipe joint sealant lightly to
male threads. This will prevent
excess sealant from going into
pipe. Excess sealant in pipe could
result in clogged heater valves.
Install sediment trap in supply line
as shown in Figure 12. Locate
sediment trap where it is within
reach for cleaning. Locate
sediment trap where trapped
matter is not likely to freeze. A
sediment trap traps moisture and
contaminants. This keeps them
from going into heater controls. If
sediment trap is not installed or is
installed wrong, heater may
not run properly.
CHECKING GAS
CONNECTIONS
A WARNING: Test all gas
piping and connections for leaks
after installing or servicing. Correct
all leaks at once.
WARNING: Never use an
open flame to check for a
leak. Apply a mixture of liquid
soap and water to all joints.
Bubbles forming show a leak.
Correct all leaks at once.
CAUTION: Make sure external
regulator has been installed be-
tween gas supply and heater. See
guidelines under Connecting to Gas
Supply.
10
Pressure Testing Gas Supply
Piping System
Test Pressures In Excess Of
1/2 PSIG (3.5 K Pa)
1. Disconnect appliance with its
appliance main gas valve
(control valve) and equipment
shutoff valve from gas supply
piping system. Pressures in
excess of 1/2 psig will damage
heater regulator.
2. Cap off open end of gas pipe
where equipment shutoff valve
was connected.
3. Pressurize supply piping system
by either using compressed air
or opening main gas valve
located on or near gas meter.
4. Check all joints of gas supply
piping system. Apply mixture of
liquid soap and water to gas
joints. Bubbles forming indicate
a leak.
Correct all leaks at once.
6. Reconnect heater and equipment
shutoff valve to gas supply. Check
reconnected fittings for leaks.
Test Pressures Equal To or
Less Than 1/2 PSIG (3.5 K Pa)
1. Close equipment shutoff valve
(see Figure 13).
2. Pressurize supply piping system
by either using compressed air
or opening main gas valve lo
cated on or near gas meter,
3. Check all joints from gas meter to
equipment shut off valve (See
Figure14) Apply mixture of liquid
soap and water to gas joints.
Bubbles forming indicate a leak.
4, Correct all leaks at once.
o
CHECKING GAS
CONNECTIONS
CONTINUED
Pressure Testing Heater Gas
Connections
1. Open equipment shutoff valve
(see Figure 13).
2. Open main gas valve located on
or near gas meter.
3. Make sure control knob of
heater is in the OFF position.
4. Check all joints from equipment
shutoff valve to control valve
(see Figure 14). Apply mixture of
liquid soap and water to gas
joints. Bubbles forming indicate
a leak.
Correct all leaks at once.
6. Light heater (see Operating
Heater, pages 11 and 12). Check
the rest of the internal joints for
leaks.
7. Turn off heater (see page 12).
о!
Open
\
Closed
Equipment
Shutoff Valve
Figure 13 -Equipment Shutoff Valve
Figure 14 -Checking Gas
Connections
OPERATING YOUR
HEATER
BE FOR YOUR SAFETY E
READ BEFORE LIGHTING
4h WARNING: № you do not
follow these instructions exactly,
a fire or explosion may result
in causing property damage,
personal injury or loss of life.
A. This appliance is equipped with
an ignition device which
automatically lights the pilot. Do
not try to light the pilot by
hand.
B. BEFORE LIGHTING smell all
around the appliance area for
gas. Be sure to smell next to
the floor because some gas is
heavier than air and will settle
on the floor.
WHAT TO DO IF YOU SMELL GAS
e Do not try to light any appliance.
® Do not touch any electric switch;
do not use any phone in your
building.
e Immediately call your gas
supplier from a neighbor's
phone. Follow the gas
supplier's instructions.
e |f you cannot reach your
gas supplier, call the fire
department.
C. Use only your hand to push on
control knob. Never use tools.
If the control konb does not
operate , don't try
to repair it, call a qualified service
technician or gas supplier. Force
or attempted repair may result in
a fire or explosion.
D. Do not use this appliance if any
part has been under water.
Immediately call a qualified
service technician to inspect
the appliance and to replace
any part of the control system
and any gas control which has
been under water.
OPERATING
INSTRUCTION
For HR20EN-1, HR30EN-1 models
with manual override control
system, make sure the ELECTRIC
Control Knob is in the electric
postion.(See Figure 15).
1. STOP! Read the safety informa-
tion above before lighting.
2. Disconnect or turn off all electric
power to heater.
3. This appliance is equipped with
an ignition device which automati-
cally lights the pilot. Do not try to light
the pilot by hand.
11
4. Wait five (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow “B” in the safety infor-
mation above. If you don't smell
gas, go to next step.
5. Plug into a properly grounded three-
prong receptacle, set ON/OFF
switch on, you will hear a high pitch
sound that indicates the burner is
ready to be operated.
6. Make sure Control Knob is in
ELECTRIC position.
7. Press IGN/OFF button an electric
spark will ignite the pilot.
8. Press BURNER button for desired
burner operation.
AUTO: Burner will automatically turn
on or off to desired temperature
setting, press or Pp for desired
temperature setting.
MAN: Burner operates continuously.
OFF:The main burner will shut off.
9. If the appliance will not operate,
follow the instructions “To Turn Off
Gas To Appliance” and call your
service technician or gas supplier.
Note: The thermostat sensing bulb
measures the temperature of air
near the heater cabinet. This may
not always agree with room tempera-
ture (depending on housing
construction, installation location,
room size, air temperatures, etc.)
Frequent use of your heater will let
you determine your own comtort
levels.
SETTING CLOCK
Clock setting: Press CLOCK button
to select item (hour, minute). The
selected item will flash. Press « or
D to change to correct time (hour,
minute). Press CLOCK button again,
to set clock.
OPERATING YOUR HEATER
continued
SETTING TIMER
AUTO ON: With burner off, press
TIMER button. Then press «lor Dto
change to the scheduled time, then
press the TIMER button again, the
TIMER starts timing and the TIMER
will flash. Burner will automatically
come on at the set time.
AUTO OFF: With burner operating,
press TIMER button. Then press €
or > to change to the scheduled
time, then press the TIMER button
again, the TIMER starts timing and
the TIMER will flash. Burner will
automatically shut off at the desired
time.
LOCKING TOUCH-PAD
(childproof)
A. Key-press locking: Press LOCK
button on the operating panel,
a da symbol will appear on the
LCD.
B. Key-press unlocking: Press > ,
then press LOCK button to unlock.
OPERATING BLOWER
Press BLOWER button, for desired
blower operation.
AUTO: Blower will come on several
minutes after burner comes on and
will go off several minutes after
blower goes off.
MAN: Blower operates continuously.
OFF: Blower is off.
TO TURN OFF GAS TO Ш
HEATER
1.Press the IGN/OFF button on the
touch pad.
2.Set the ON/OFF switch to OFF
position on top panel.
NOTE: Wait one minute to light
again after shutting off heater.
E MANUALOPERATING H
INSTRUCTIONS
If no electric power is available,
you can operate heater manually.
Install battery for Manual Ignitor:
A WARNING: Do not install bat-
tery backwards, change or put in
fire-may explode or leak.
1. Remove round access door on
right side panel.
2.Unscrew the ignitor cap.
3. Insert a AAA type battery with its
anode (“+”) pointing out.
4. Screw the ignitor cap back .
Note: We recommend that the bat-
tery be taken out of the ignitor when
the power supply has been restored
1. STOP! Read the safety infor-
mation on page11 before lighting.
2. Check that gas supply to the
heater is on.
Control Knob GFT Te
{=a
Yoox Y A
Jon [gnitor Button
Led
\
12
3. Push in control knob slightly and
turn clockwise /”y to the OFF
position.If the manual control knob
points to ELECTRIC position, press
in the control knob and turn counter
clockwise y to OFF position.
. Wait five (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow “B” in the safety infor-
mation on page11. If you do not
smell gas, go to the next step.
Push in gas control knob slightly
and turn counterclockwise y to
PILOT/IGN and depress for five(5)
seconds. NOTE: The first time the
heater is operated after connecting
the gas supply, the control knob
should be depressed for about thirty
(30) seconds. This will allow air to
exit the gas system.
. With control knob pressed, push
ignitor button. This will light the
pilot. If needed, keep ignitor button
pressed until pilot lights.
. Keep control knob depressed for
ten (10) seconds after lighting
pilot. If pilot goes out, repeat
steps 5,6 and 7.
. Rotate counterclockwise , to
ON position to light burner. Do not
operate between locked positions.
MANUAL OPERATING E MANUAL LIGHTING Ш
INSTRUCTIONS PROCEDURE
continued (Match Light)
9. When electric power is available + Remove lower front panel.
and electronic operation is 2. Follow steps 1 through 5
desired, turn clockwise /\ to under Manual Operating
OFF positon for one minute. Then Instructions on page 12.
press down knob and rotate 3. With control knob pressed in,
clockwise y to ELECTRIC strike match. Hold match
position. Do not operate between to pilot until pilot lights.
locked positions.
4. Keep control knob pressed in Figure 17- Incorrect Pilot Flame
Pattern
BURNER FLAME PATTERN
Figure 18 shows a correct burner
for 30 seconds after lighting
pilot.
5. Rotate counterclockwise Y qto
/ ON position to light burner. Do flame pattern. Figure 19 shows an
not operate between locked incorrect burner flame pattern. If
EL positions. burner flame pattem is incorrect,
Figure 15- Manual Control 6. Replace lower front panel as shown in Figure 19.
e turn heater off (see page 12).
INSPECTING BURNER
= TOTURNOFFGASTO IM Check pilot flame pattern and
APPLIANCE
® see Troubleshooting, pages 17
burner flame pattern often. through 19.
Push in gas control knob slightly PILOT FLAME PATTERN
and turn clockwise y to OFF. Figure 16 shows a correct pilot
Do not use force. NOTE: Wait one flame pattern. Figure 17 shows an
1) minute with control knob in incorrect pilot flame pattern. The
(1) . E Figure 18 - Correct Burner
OFF position before operating incorrect pilot flame is not touch- Flame Pattern
heater. ing thermocouple. This will cause
the thermocouple to cool. When
a Fri
fo
eye Y
the thermocouple cools, the
|
|
|
|
||
|
|
healter will shut down. If pilot flame
И
Figure 17. Figure 19 - Incorrect Burner
® turn heater off (see page 12). Flame Pattern
pattern is incorrect, as shown in
e see Troubleshooting, pages 17
through 19.
13
CLEANING AND
MAINTENANCE
A WARNING: Disconnect
power before attempting any
maintenance or cleaning to reduce
the risk of fire , electric shock or
personal injury. Turn off heater and
let cool before cleaning.
A WARNING: Failure to keep
the primary air opening(s) of the
burner(s) clean may result in sooting
and property damage.
A CAUTION:Label all wires prior tq
disconnection when servicing
controls.Wiring errors can cause
improper and dangerous operation.
Verify proper operation after
servicing.
A CAUTION: You must keep
control areas, burner, and circulat-
ing air passageways of heater
clean. Inspectthese areas of heater
before each use. Have heater in-
spected yearly by a qualified ser-
vice person. Heater may need more
frequent cleaning due to excessive
lint from carpeting, bedding material,
pet hair, etc.
DISCONNECT WIRING ON
CONTROL MODULE
1. Remove two screws from the lower
front panel , pull the lower front panel
forward then down, take out thermostat
sensing bulb from the clip, then disco-
nnect the wires from control module .
Note: Do not confuse the mark on each
wire.
2. Remove two screws and hex nuts,
take out the control module. When
installing , reverse the steps above.
(See Figures 20 and 23)
Sensing Bulb
Power Cord
o
Lower Front panel
Figure 20 Control Module Access
DISCONNECT FAN
1. Remove screws from the fan
bracket panel, pull the fan bracket
panel out to remove. Disconnect
two wires of temperature sensor.
2. Markortag each wire removed for
its exact reconnection. Remove the
four screws from the fan, when
installing , reverse the steps above.
(See Figures 21 and 23)
y
Fan Bracket
/ Panel
Back Panel
Figure 21- Fan Access
CLEANING ODS/PILOT AND BURNER
e Use a vacuum cleaner,pressurized
air, or small, soft bristled brush
to clean.
CLEANING BURNER AND PILOT
AIR INLET HOLE
We recommend that you clean the
unit every 2,500 hours of operation
or every three months. We also
recommend that you keep the burner
tube and pilot assembly clean and
free of dust and dirt.
14
To clean these parts we recommend
using compressed air no greater
than 30 PSI. Your local computer
store, hardware store, or home center
may carry compressed air in a can.
You can use a vacuum cleaner in the
blow position. If using compressed
air in a can, please follow the direc-
tions on the can. If you don’t follow
directions on the can, you could dam-
age the pilot assembly.
1. Shut off the unit, including the
pilot. Allow the unit to cool for
at least thirty minutes.
Inspect burner, pilot for dust
and dirt.
3. Blow air through the ports/slots
and holes in the burner.
Clean the pilot assembly also. A
yellow tip on the pilot flame indi-
cates dust and dirt in the pilot
assembly. There is a small pilot air
inlet hole about two inches from
where the pilot flame comes out of
the pilot assembly (see Figure 22).
With the unit off, lightly blow air
through the air inlet hole. You may
blow through a drinking straw if
compressed air is not available.
Pilot Air Inlet
Hol
Pilot Assembly
Figure 22 - Pilot Air Inlet Hole
CLEANING HEATER CABINET
Air Passageways
e Use a vacuum cleaner or
pressurized air to clean.
Exterior
® Use a soft cloth dampened with
a mild soap and water mixture.
Wipe the cabinet to remove dust.
ea — (1) > Thermocouple
ZZ)
És
o)
© Control Module ©
Л JZ IB XA
pi Pa
1000 000000==11
1
9 man Ÿ
8 Te e e
ON/OFF “ / |< Е |8 ВЕ БЁ |°Ё
Switch = = |]
= a Touch pad
D о œ Temp Sensor
- BS вю 9-| BV 1
= = Fan T-Stat “18” à ELOWER
= Switch a | (@] Electronic
ne Ignitor
il ©) :
Normally 2 =
Closed
Switch
Black—
If any of the original wire as supplied with the appliance must be
Bush replaced, it must be replaced with a wire of at least a 105°
Control Valve temperature rating.
Caution: Label all wires prior to disconnection when servicing controls.
Wiring errors can cause improper and dangerous operation.
Power Cord Verify proper operation after servicing.
~120V 60HZ
[Fan Type Unvented Heater |
Figure 23- Double Control System Diagram
(Model HR20EN-1 HR30EN-1)
15
REPLACEMENT PARTS PARTSNOTUNDER FLOOR MOUNTING STAND
x WARRANTY
Note: Use only original replacement | Eorlocatina heater on the floor
parts. This will protect your warranty Contact authorized dealers of this 9 ,
coverage for parts replaced under Product. If they can’t supply original away from a wall
warranty. replacement part(s), call HearthRite's
h ber 1- 618-233-7420 or 1- |
PARTS UNDER WARRANTY phone number or | =
800-851-3153.
Contact authorized dealer from 1
whom you purchased this product. TECHNICAL SERVICE ==
If they are unable to supply original You may have further questions — тЫ пед
replacement part(s), са! the number about installation, operation, or ПОВ
on the front of manual. When con- troubleshooting. If so, contact |
tacting your dealer or HearthRite, have HearthRite's phone number 1- 618- ITT — ТО
ready: 233-7420 or 1-800-851-3153. NTE A
> your-fame EEE |
e your address о ЗОНЕ
e model and serial numbers of mis =
your heater
e how heater was malfunctioning
e type of gas used (propane/LP or
natural gas) Refer to base instructions for
® purchase date attaching floor stand.
e warranty card
Usually, we will ask you to return the
defective part to the factory.
SPECIFICATIONS
HR20EN-1 HR30EN-1
BTU/Hr 20,000 30,000
Gas Type Natural Gas Only Natural Gas Only
Ignition Automatic/Electronic Automatic/Electronic
Volts 120 V 120 V
Watts 20 W 27W
Manifold Pressure 6" W.C. 4" W.C
Inlet Gas Pressure (inches of
water)
Maximum 10.5" 10.5"
Minimum* 7" 7
Dimensions, Inches (HxWxD)
Heater 23 5/8x19 5/8x9 23 5/8x27 1/16x9
Carton 27 1/2x22x10 1/8 27 1/2x29 7/16x11 1/8
Weight (pounds)
Heater 34 43
Shipping 39 56
Note: Dimensions listed are outer most points on the heater (includes grill).
* For purposes of input adjustment.
TROUBLESHOOTING
ÁN WARNING: If you smell gas
Shut off gas supply.
Оо по! гу to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor's phone. Follow the gas
supplier's instructions.
e |f you cannot reach your gas supplier, call the fire department.
IMPORTANT: Operating heater where impurities in air exist may create odors.
Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new
carpet or textiles, etc., create fumes. These fumes may mix with combustion air
and create odors.
Warning : Make sure that power
is turned off before proceeding.
OBSERVED PROBLEM
pair heater.
WARNING: Turn off and let cool be;
fore servicing. Only a qualified ser:
vice person should service and re:
A CAUTION: Never use a wire,
needle, or similar object to clean
ODS/pilot. This can damage
ODS/pilot unit.
POSSIBLE CAUSE
REMEDY
When ignition button is pressed, 1. No power to heater 1. Check the electric power
there is no spark at ODS/pilot ~~ 2 ON/OFF switch not ON 2. Turn ON/OFF switch ON
3. Wire is damaged or loose 3. Check the wire for damage and
make sure connection is tight
4. Pilot electrode position is not correct 4. Replace Pilot
5. Touch pad cable is not connected 5. Reconnect touch pad cable
6. System halt 6. Place the control knob of manual
override on OFF position for at
least 1 minute, then turn to
ELECTRIC position
Spark at ODS/pilot but no ignition — 1, Gas supply turned off or equipment 1. Тит on gas supply or open
shut off valve closed equipment shutoff valve
2. Air in gas lines when installed 2. Press ignitor button again until air
is removed
3. Depleted gas supply 3. Contact local gas company
4. ODS/pilot is clogged 4. Clean ODS/pilot (see Cleaning
and Maintenamce, Page 14) or
replace ODS/pilot assembly
5. Gas inlet supply pressure not correct 5. Have qualified service technician
check inlet pressure
6. Wire is damaged or loose 6. Check the wire for damage and
make sure connection is tight
7. Pilot electrode position is not correct 7. Replace Pilot
8. Gas valve or regulator is damaged 8. Contact dealer or HearthRite
ODS/pilot has flame, but continues 1. Equipment shutoff valve is not 1. Fully open equipment shutoff valve
to spark fully open
2. Thermocouple connection 2. Check that connectors are secureon
loose at control module module
3 Low gas pressure 3. Contact local natural gas
company
4. Dirty or partially clogged ODS/pilot 4. Clean ODS/pilot (see Cleaningand
Maintenance, Page 14) or replace
ODS/pilot assembly
5. Thermocouple damaged 5. Replace thermocouple
6. Gas valve or regulator damaged 6. Contact dealer or HearthRite
17
TROUBLESHOOTING
Continued
OBSERVED PROBLEM POSSIBLE CAUSE REMEDY
ODS/pilot has flame, but burner(s) 1. Burner injector is clogged 1. Clean burner injector (see Cleaning
does not light and Maintenance, Page14) or
replace burner injector
2. Inlet gas pressure is too low 2. Contact local natural gas company
3. Thermocouple leads disconnected 3. Reconnect leads (See Wiring
or improperly connected Diagram)
4. Batteries weak 4. Replace batteries
—
—
Manifold pressure is too low Contact local natural gas company
2. Burner injector is clogged 2. Clean burner (see Cleaning and
Maintenance, Page 14) or replace
burner injector
Delayed ignition of burner(s)
Burner backfiring during combustion 1. Burner injector is clogged or 1. Clean burner injector (see Cleaning
damaged and Maintenance, Page 14) or
replace burner injector
2. Burner is damaged 2. Replace burner
3. Excessive supply pressure 3. Replace gas regulator
damaged regulator
Burner Plaque(s) does not glow 1. Plaque damaged 1. Replace burner
2. Inlet gas pressure is too low 2. Contact local natural gas
company
Slight smoke or odor during 1. Residues from manufacturing 1. Problem will stop after a few hours
initial operation processes of operation
Heater produces a clicking/ticking 1. Metal expanding while heating or 1. This is common with most
noise just after burner is lit or contracting while cooling heaters. If noise is excessive,
shut off contact qualified service person
White powder residue forming 1. Heated vapors from furniture 1. Turn heater off when using furniture
within burner box or on adjacent polish, wax, carpet cleaners, polish, wax, carpet cleaner, or
walls or furniture etc. turn into white powder similar products
residue
18
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE REMEDY
Heater produces unwanted odors 1. Heater is burning vapors from 1. Ventilate room. Stop using odor
paint, hair spray, glues, etc. causing products while heater
(See IMPORTANT statement is running
at beginning of troubleshooting)
2. Gas leak. See WARNING 2. Locate and correct all leaks(see
Statement at beginning of Checking Gas Connections,
troubleshooting Page 10)
Heater shuts off in use (ODS 1. Notenough fresh air is available 1. Open window and/or door for,
operates) ventilation
2. Low line pressure 2. Contact local natural gas
company
3. ODS/pilot is partially clogged 3. Clean ODS/pilot (see Cleaning
Page 14)
Gas odor exists even whenheateris 1. Gas leak. See WARNING 1. Locate and correct all leaks(see
shut off Statement at beginning of Checking Gas Connections,
troubleshooting Page 10)
Gas odor during combustion 1. Foreign matter between control 1. Remove foreign matter
valve and burner
2. Gas leak See WARNING 2. Locate and correct all leaks
Statement at beginning of (see Checking Gas
troubleshooting Connections, Page 10)
Moisture/condensation on windows 1. Not enough combustion/ 1. Refer to Air for Combustion and
ventilation air Ventilation requirements, Page
5
NOTE: BEFORE YOU SWITCH TO “ELECTRIC” CONTROL POSITION FROM MANUAL CONTROL, YOU
NEED TO TURN THE KNOB TO “OFF” POSITION FIRST AND WAIT FOR ONE MINUTE, THEN TURN THE
KNOB TO “ELECTRIC”.
IN CASE OF “ELECTRONIC” CONTROL LEVEL DOES NOT WORK, PLEASE TURN THE CONTROL KNOB
COUNTERCLOCKWISE TO “OFF” POSITION AND WAIT FOR ONE MINUTE.
19
ILLUSTRATED
PARTS BREAKDOWN
HR20EN-1
A
| m me f |
|
|
TN
D id
emm |
o-- Inne... LA
22 —=
sp, {Ne 6
EQ Ie |
0
met 7 \ В
18 24 19
32
_ / I /
197 ©
pet | Тонн!
[1] |
| |
| | y ||
20
|
PARTS LIST
This list contains replaceable parts for your heater. When ordering replacement
parts, following the instructions listed under Replacement Part on page 16 of this
HR20EN-1 manual.
KEY | IRON DESCRIPTION QTY
NO. PART NO.
1 MCL002-01 Left panel 1
2 MCL003-01 Right panel 1
3 MCL003-01B Door 1
4 MCLO001-02 Cabinet Top 1
5 MCL008-01 Hinge 1
6 MCL004-02 Top panel 2
7 MCB07001 Louver Assembly 1
8 MCB62001 Blower Thermostat Switch Asm 1
9 NFHTX Blower Assemble 1
10 MCB1100B Reflector Unit 1
11 MCLO17-08E Grill guard ASS Y 1
12 MCB09002 Lower Front Panel Assembly 1
13 MCB19004 Burner Assembly 1
14 ND4703X400-RH | ODS/Pilot Assembly 1
15 ND0803-C2 Thermocouple 1
16 ND0807 Ignitor Electrode 1
16-1 MCLO93-01 Power 1
16-2 | NAM03-00 Control Module 1
17 NAM03-07 Temperature Sensor 1
18 NRV81FIL-6 Regulator 1
19 AL092-01 Ignitor 1
20 MB16004 Control Knob 1
21 "MCL099-01 Control ASSY 1
22 NV2020-22 Control Valve Assembly 1
23 MCB40007 Regulator To Valve Tube 1
24 MCB40033 ODS Gas Line Assembly 1
25 MCB40006 Valve To Burner Tube 1
26 MCBLO36-01 Four-Way Connector 1
27 MCL092-01 Injector 2
28 MLO90-07 Injector 1
29 МАМО2-00 Touch Pad 1
30 VL067-01 ON/OFF Switch 1
31 PF0920C-01 Left Base 1
32 PF0920C-02 Right Base 1
PART AVAILABLE NOT SHOWN
MCB28001 Hardware Assembly 1
MCLO55-02 CSA/AGA Decal 1
MCLO46-01 Lighting Instruction Plate 1
MCL046-02 Warning Plate 1
21
ILLUSTRATED
PARTS BREAKDOWN
HR30EN-1
— a=
MON
? lo
i
22
PARTS LIST
This list contains replaceable parts for your heater. When ordering replacement
parts, following the instructions listed under Replacement Part on page 16 of this
HR30EN-1 manual.
ah DESCRIPTION QTY
1 MCL006-01 Back panel 1
2 MCL002-01 Left panel |
3 MCL003-01 Right panel 1
4 MCL003-01B Door 1
5 MCLO001-01 Cabinet Top 4
6 MCL008-01 Hinge 2
7 MCL004-01 Top panel 1
8 MCL024/025-01 [Left/Right Liner panel 2
9 MCB07001 Louver Assembly 1
10 MCB62001 Blower Thermostat Switch Asm 1
11 NFHTX186 Blower Assembly 1
12 MCB1102 Reflector Assembly 1
13 MCLO17-10E | Grill guard ASSY 1
14 MCBO9001 Lower Front Panel W/Brackets 1
15 MCB19001 Burner Assembly 1
16 ND4103X400-RH | ODS /Pilot Assembly 1
16-1 | ND0803-4C Thermocouple 1
16-2 | ND0807-C3 Ignitor Electrode 1
17 MCLO93-01 Power Cord 1
18 МАМОЗ-00 Control Module Asembly 1
19 NAM03-07 Temperature Sensor 1
20 NRV81FIL-4 Regulator 1
21 AL092-01 Ignitor 1
22 MB16004 Control Knob 1
23 MCL099-01 Control Switch 1
24 NV2020-22 Control Valve ASSY 1
25 MCB40001 Main Intlet Tube Assembly 1
26 MCB40020 ODS Gas Line Assembly 1
27 MCB40002 Main Inlet Tube Assembly 1
28 MCBL036-02 |Six-Way Connector 1
39 MLO90-08 Injector 1
30 MCB40021 Burner Gas Line Assembly ci and c2 5
31 MCB40022 Burner Gas Line Assembly b1 and b2 1
39 MCB40023 Burner Gas Line Assembly A 1
33 NAM02-00 Touch Pad 1
34 VL067-01 ON/OFF Switch 1
35 PF0920C-01 Left Base 1
36 PF0920C-02 | Right Base 4
1
PART AVAILABLE NOT SHOWN
MCB28001 Hardware Assembly 1
MELO55-02 CSA/AGA Decal 1
MCLO46-01 Lighting Instruction Plate 1
MCL046-02 Warning Plate 1
23
WARRANTY INFORMATION
KEEP THIS WARRANTY
SERIAL NUMBER
LABEL
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our
standard written warranty. We make no other warranty, expressed or implied.
/ /
LIMITED WARRANTY HEARTHRITE VENT-FREE-FIREPLACE Gas 374 ce Meatens
HearthRite warrants this product to be free from defects in materials, components except for electrical components
and limited labor for (3) three year and electrical components for (1) year from the date of first purchase, provided
that the product has been properly installed, operated and maintained in accordance with all applicable instructions.
To make certain under this warranty, the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to
restore this heater to proper operating condition and an allowance for labor when provided by a HearthRite
Authorized Service Center. Warranty part(s) MUST be obtained through authorized dealers of this product and/or
HearthRite who will provide original factory replacement parts. Failure to use original factory replacement parts voids
this warranty. The heater MUST be installed by a qualified installer in accordance with all local codes and instructions
furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear or parts that
fail or become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper
installation.
Some States do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental
or consequential damages, so the above limitation on implied warranties, or exclusion or limitation on damages may
not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. For
information about this warranty, please write to:
HearthKite
A Division of Empire Comfort Systems, Inc.
918 Freeburg Avenue
Belleville, 11. 62220
Phone : 618-233-7420 or 1-800-851-3153
Fax : 618-233-7097 or 1-800-443-8648
www. hearthrite.com
24

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement