Installation Guide
Case components
Hardware list
Buzzer (1)
USB 3.0 to USB 2.0 converter (1)
Cable ties (2)
140mm fan
Multi-media ports
Power switch
Reset switch
5.25" mounting bezels
Removable
120mm fans with air filter
120mm fan
Rubberized grommets for liquid cooling tubing
Patented tool-less
PCI add-on card holder
Patented tool-less
PSU mounting bracket
Longer thumb screw (3) for motherboard mount
Shorter thumb screw (6) for motherboard mount
Bracket (1) for power supply mounting
Thumb screw(24) for HDD
Rubber slide rail (12) for HDD
Patented tool-less 5.25” device mounting
Hot swap
3.5" HDD cage
(For 3.5" HDD x 6)
Removable
2.5" HDD module
(For 2.5" HDD x 2)
Screw (4) for PSU mounting
Screw (20) for 2.5" HDD/spare parts
Key is in the accessories box
!
!
!
Note:
For hard to reach areas use long thumb screws.
Remove four thumb screws.
Remove front panel
Slide the panel backward to release.
Place the M/B on the copper bolt and secure with thumb screws.
3.5” HDD module installation Cable management
Pull the front panel towards yourself.
Install the screws to the HDD with anti-vibration rubber slide rail.
Slide the HDD into the HDD cage.
2.5" HDD module installation
Fasten eight screws.
Slide the HDD into the HDD cage.
Close the gate to secure the HDD.
Lock.
C50.Z6000.01E-1
ODD installation
Press the right and left sides of the bezel to remove.
PSU installation
Press the plastic handle to release the mounting bracket.
Push the ODD into the 5.25” rack.
Close the bracket to secure the
ODD.
Place the PSU on the stand, and push against the rear panel.
PCI add-on card installation
Place the PSU bracket into the slot as shown.
Lock the PSU bracket to secure the PSU.
Remove air filter
Washable air filter below the PSU
1
2
Open the aluminum latch to remove the PCI slot bracket.
Push the card into the PCI slot, close the aluminum latch to secure the card.
Slide the air filter to remove.
Change fan from right-side to left-side
* For transportation, please use
screws to secure the PSU.
Washable air filter on the right-side
Rotate washable air filter clockwise to remove.
Supports liquid cooling systems
Slide the fan up to remove.
Remove five screws to release the bracket.
I/O port installation
E-SATA USB 2.0 USB 3.0
USB 3.0
MIC EAR
USB 3.0
Supports motherboard
USB 3.0 20 Pin header
USB 2.0
HD AUDIO
BLUE 10
BLACK PURPLE
YELLOW
BROWN
RED
4
2
8
6
Place the bracket on the other side, fasten five screws to secure.
9
7
5
3
1
GREEN
KEY
ORANGE
N.C.
GND+H.S. TUBE
E-SATA
Place the fan into the bracket and slide down to secure.
SATA
Cable
Cable installation guide
GROUND
PWR
GROUND
Reset
PLED-
PLED+
IDE_LED-
IDE_LED+
Speaker
+5V
WHITE
GRAY
WHITE
BLUE
WHITE
NC
GREEN
WHITE
ORANGE
BLACK
NC
NC
RED
POWER SW
RESET SW
POWER
LED
H.D.D LED
SPEAKER
USB 3.0 to USB 2.0 converter
20 1
11 10
VCC
D-
D+
GND
RED
WHITE
GREEN
BLACK
RED
WHITE
GREEN
BLACK
KEY
VCC
D-
D+
GND
C50.Z6000.01E-2
