Installation Guide
Case components
140mm fans x 2
Multi-media ports
Power switch
Reset switch
5.25" mounting bezels
Removable
120mm fans with air filter
Rubberized grommets for liquid cooling tubing
120mm fan
Patented tool-less
PCI add-on card holder
VGA card support column
Patented tool-less
PSU mounting bracket
Hardware list
Buzzer (1)
USB 3.0 to USB 2.0 converter
Bracket (1) for power supply mounting
Screw (4) for PSU mounting
Screw (20) for 2.5" HDD/spare parts
Longer thumb screw (3) for motherboard mount
Shorter thumb screw (9) for motherboard mount
Screw driver (1) to ass’y motherboard
Stand off bolt (3) for motherboard (spare parts)
Mounting bracket for SSI CEB/EEB M/B
Thumb screw(36) for HDD
Rubber slide rail (18) for HDD
Cable ties (2)
Nut (3) for stand off
Patented tool-less 5.25” device mounting
Hot swap
3.5" HDD cage
(For 3.5" HDD x 9)
Removable
2.5" HDD module
(For 2.5" HDD x 2)
PCI card holder/B (4)
PCI card holder/A (8)
Thumb screw (8) for PCI card holder
Box (1) for spare parts
Key is in the accessories box
1
2
Remove six thumb screws.
Remove front panel
Slide the panel backward to release.
ODD installation
Remove four thumb screws, to release the VGA card support column
!
!
!
Note: For hard to reach areas
use long thumb screws.
for SSI CEB/EEB
The oval hole on the M/B tray is designed for special server boards. Please use a nut to secure the copper bolt in place
Place the M/B on the copper bolt and secure with thumb screws.
Pull the front panel towards yourself.
Press the right and left sides of the bezel to remove.
Press the plastic handle to release the mounting bracket.
Push the ODD into the 5.25" rack.
Close the bracket to secure the ODD.
3.5” HDD module installation 2.5” HDD module installation
2
L
Install the screws to the HDD with anti-vibration rubber rings.
Slide the HDD into the
HDD cage.
Fasten eight screws.
Slide the HDD into the
HDD cage.
1
1.Close the gate to secure
the HDD.
2.Lock.
C50.Z7000.01E-1
PSU installation
Place the PSU on the stand, and push against the rear panel.
Place the PSU bracket into the slot as shown.
Lock the PSU bracket to secure the PSU.
VGA card pillar installation guide
* For transportation, please use
screws to secure the PSU.
Cable management
L
Insert PCI card holder/A
PCI add-on card installation
Use PCI card holder/B for thick VGA cards.
Remove air filter
Washable air filter below the PSU
1
2
Open the aluminum latch to remove the PCI slot bracket.
Push the card into the PCI slot, close the aluminum latch to secure the card.
Slide the air filter to remove.
Change fan from right-side to left-side
Washable air filter on the right-side
Rotate washable air filter clockwise to remove.
Supports liquid cooling systems
Slide the fan up to remove.
Remove six screws to release the bracket.
I/O port installation
E-SATA USB 2.0 USB 3.0
USB 3.0
MIC EAR
USB 3.0
Supports motherboard
USB 3.0 20 Pin header
HD AUDIO
BLUE 10
BLACK PURPLE
YELLOW
BROWN
RED
4
2
8
6
USB 2.0
Place the bracket on the other side, fasten six screws to secure.
Place the fan into the bracket and slide down to secure.
9
7
5
3
1
GREEN
KEY
ORANGE
N.C.
GND+H.S. TUBE
E-SATA
SATA
Cable
Cable installation guide
GROUND
PWR
GROUND
Reset
PLED-
PLED+
IDE_LED-
IDE_LED+
Speaker
+5V
WHITE
GRAY
WHITE
BLUE
WHITE
NC
GREEN
WHITE
ORANGE
BLACK
NC
NC
RED
POWER SW
RESET SW
POWER
LED
H.D.D LED
SPEAKER
USB 3.0 to USB 2.0 converter
20 1
11 10
VCC
D-
D+
GND
RED
WHITE
GREEN
BLACK
RED
WHITE
GREEN
BLACK
KEY
VCC
D-
D+
GND
C50.Z7000.01E-2
