Kodak Signet 35 Guide
Kodak Signet 35, a precision-built, sturdy camera, offers a range of features for capturing sharp, clear images. Its 44mm f/3.5 Lumenized Ektar lens, coupled with the superimposed image-type range finder, ensures accurate focus. The built-in Kodak Synchro 300 Shutter allows for flash synchronization up to 1/300th of a second, making it suitable for various lighting conditions.
PDF
Document
Advertisement
Advertisement
DETAILS of Kodak Signet 35 Camera Film NEGATIVE S1ZE—24 x 36mm (approx 1"x14"). FILM Size—Kodak 135; 20- or 56-exposure magazine. Lens Konak ExTar—44mm f/3.5, Lumenized lens. LENs OPENINGS—f/3.5, f/4, f/5.6, f/8, f/11, f/16, f/22. COMBINATION LENS ATTACHMENTS — Series V — No. 22 Kodak Adapter Ring (Screw-in Type), or 1%” Kodak Adapter Ring (Slip-on Type). Shutter KODAK SYNCHRO 300—Cocking type. SPEEDS—1/25, 1/50, 1/100, 1/300 and “B.” Bony RELEASE—Right front of camera body. FLASH—Built-in synchronization for Class M (No. 5 or 25) flash lamps. Focusing and Viewing RANGE FINDER—Superimposed type, combined with view finder, coupled to focus mount. Focusing Rance—2 feet to infinity. View FinpeEr—Optical, eye-level enclosed, combined with range finder. DouBLE-EXPOSURE PREVENTION— Film advance interlocked with body shutter release to provide double-exposure prevention. Construction CAMERA StzeE—4% x 3% x 2% inches. ‘ Bony—Die-cast alloy with black Kodadur covering. Back—Same as body, with metal pressure pad. Back is readily removable for easy access in loading. TriIPOD SockET—Standard tripod thread for tripod or Kodak Flasholder Bracket. SERIAL NumBER—For positive identification — is stamped on the top of the case under the rewind knob. Keep a record of this number with your personal papers. Eastman Kodak Company e Rochester 4, N. Y. 9-52-CH-DX PRINTED IM THE UNITED STATES OF AMERICA - №" E O. - Г. ЧЕ 4 a TAI <a Ch =p E Мл Е, 1 SEE e. ОННЩИ ный ed frat т i "e a | np po “a mail wiper i * The fine appearance of this camera is matched by its performance and operation. Precision-built, sturdy, and amazingly easy to use, the Kodak Signet 35 Camera has features that provide results comparable with the finest cameras. Before using your camera, take a few minutes to get acquainted with it. Go through this manual with the camera, performing each operation as indicated, Then, when the moment of picture making arrives, you will be ready. Before making any important pictures—a trip, some special event, or any pictures expected to prove valu- able — you should shoot a roll or two of film and take a few flash pictures. This will give you practice and pro- vide a check on your equipment. If you have any questions, your Kodak dealer will always be glad to help you in any way he can. The automatic double-exposure mechanism and film counter are designed lo work when the cam- era is loaded. The double-expo- sure prevention mechanism may not work and the film counter will not work without film in the camera. T.M. REG. U.S. PAT. OFF. OPERATING FEATURES Kodak Ektar Lens Pictures produced with your Kodak Signet 35 Camera and its highly corrected Kodak Ektar 44mm f/3.5 Lumenized Lens are clear and needle-sharp. Kodak Synchro 300 Shutter With its built-in synchronization capable of taking flash shots up te 1/300 second, your camera is well equipped for a remarkably wide range of picture-making situations. Coupled Range-Finder The superimposed image-type range finder is coupled with the lens to give instant and accurate focus. À single eyepiece serves both the range and view finders. Exposure Guide A unique, built-in picture-making aid, the exposure guide on the com- era back provides for rapid deter- mination of the lens and shutter settings. It can also be used as a reminder of the type of film in your camera, | 3 ес т ве El Пр A 2 TE RETA de DrisadT Lap осн! eE mart = en Fila ire | YEE Depth-of-Field Scale For correct ranging accuracy, the depth-of-field scale, located just above the focusing mount, gives you instant reference lo compose your picture for near and far objects. Fa ” i A Ta a a чт [8 5 Wee Qe SES, > Film Counter There's no guesswork to the number of pictures you hove snapped. The film counter accurately records the number of unexposed frames of film remaining in the film magazine. Convenient Size Knobs The wind and rewind knobs on the Kodak Signet 35 Camera have been designed for easy turning. An arrow on the top of each knob gives the direction in which the knob should be turned. Double-Exposure Prevention Built into the camera mechanism is an automatic device to prevent double exposures. The lever located on the camera front will enable you to make intentional double expo- sures if desired, see page 17. 5 8 10 12 14 16 17 18 21 22 24 26 28 31 Loading 3 Simple Settings Exposure Guide Depth of Field Box Camera Simplicity Taking the Picture Unloading Flash Pictures Flood Pictures Around the Clock Picture Taking Films Tips for Better Pictures Accessories Kodak Portra Lens Tables The tinted appearance of the lens is due to Lumenizing—a special hard coating applied to all air-glass surfaces of the lens. This treatment improves the brilliance of black-and-white pictures and the color purity of full-color pictures. + LOADING 1. Press the LATCH down firm- ly with the ball of the index finger while sliding the back < lock down with the thumb. Swing the back out 90° and lift it off the camera. 2. Pull out the REWIND KNOB. Insert the film magazine in the recess under the knob. The end of the magazine containing the crosspiece goes toward the rewind knob. Push in the rewind knob, turning the knob until it en- gages the slot with the cross- piece in the magazine, у Si — TEE EEE I dre А О, Eh ul [E VA | pa | ji i = CM a Е VA Ko Sos 3. Bend the film leader between the first and second perforation; then insert the hooked end of the film into the slot of the take-up reel. Do not try to remove this reel, 4, Turn the WINDING KNOB in the direction of the arrow until the slack is removed from the film. The teeth of the SPROCKET must fit into the holes in the film. Replace the camera back. Turn the winding knob until it locks. WINDING KNOB __— X 5. Free the winding knob by pushing the REWIND LEVER toward the rewind knob. Hold the lever and turn the winding knob % turn. Then release the lever and turn the winding knob until it locks. Do this three times. The winding knob should be turned with a steady, even mo- tion—never in a rapid and jerky manner. It is not necessary to use the REWIND LEVER to advance the film after the shutter is released. The winding knob is automatically freed when you snap a picture. However, if you accidentally trip the double-exposure lever, it will be necessary to hold the REWIND LEVER until the winding knob is turned Y turn. 6. Turn the film counter in the direction of the arrow to 20 for à 20-exposure magazine—to 36 for à 36-exposure magazine. The counter will move a mark for each picture taken. It shows the number of exposures remaining. After each exposure, turn the winding knob until it locks. This advances the film for the next picture. к. SIMPLE SETTINGS A. Shutter Speed Move the knurled ring un- til the pointer is at the desired shutter setting. The pointer “click stops" at each speed. The shut- ter must be cocked for all settings including "B." Cock the shutter by press- ing the COCKING LEVER down as far as it will go before each exposure. Never oil the shutter. B. Lens Opening The size of the lens open- ing is changed by moving the lens pointer across the scale. The pointer “click stops'' at each morked lens opening. C. Focus Look through the eye- piece of the range finder, with the camera pressed firmly against the face. Select any vertical line in your subject and move the focusing ring until the two images of the subject coincide. For accuracy, focus the subject directly under the peak of the triangle. 9 L JA TT IT ATT Зе HOW TO USE THE Dark Subjects People in dark cloth- ing, dark foliage, flow- ers, animals, buildings. Strong Shadows ОНИ, Mura - Average Subjects Near-by people, gor- dens, houses, scenes not in shade. Light and dark objects in about equal proportions. Use this class if in doubt. Hazy Sun Soft Shadows EXPOSURE GUIDE Light Subjects Distant scenery, near- by people in marine, beach, snow scenes. Light-colored objects dominating. Cloudy Bright No Shadows 7/354 588 1 IS TE OPENNG © After you have focused on your subject, that subject will be sharp in the picture. However, other objects in the picture area, both in front of and beyond the subject, will also appear in focus. This is range of sharpness or “depth of field.” The method of determining depth of field by the scale is shown in the illustrated example to the left. Subject focused on is at 15 feet; exposure calls for a lens opening of f/8. Look for the lens openings on the depth-of-field scale. There is one on each side of the distance arrow. The figure 8 is opposite f/8 on one side of the arrow. Infinity is opposite f/8 on the other side of the arrow. These show that all objects from 8 feet to infinity will be sharp and clear. DEPTH OF FIELD A large lens opening was used to obtain a shallow depth of field. DL A J ; В DL ME LE i a = - = Pr y ki 1 Es ue 4 IF YOU WANT IT box camera simplicity 16 TAKING THE PICTURE The Finder Hold the camera firmly against the face. To frame the picture, hold the camera at that distance from the eye which allows you to superimpose the rear finder frame on the front finder frame (see diagram below). To compose the picture, move the camera and your head simultaneously. The view finder is designed for correct aiming of the camera throughout the entire focusing range, provided the eye is positioned as suggested above. The range finder triangle can be used to help center your eye. The illustrations show the most practical manner of holding the camera to guard against camera move- ment at the moment of exposure. With the camera steadied against the face, depress the exposure release with a slow, squeezing action. Note: The release will remain locked if the shutter is not cocked, or the film has not been advanced to an unexposed frame. It sometimes may be necessary after an exposure to turn back the winding knob a trifle to release the winding mechanism. For intentional double exposures, trip the lever on the bottom of the front of the camera. Cock the shutter and make your sec- ond exposure. UNLOADING THE FILM UE: Нее ; EJE ra ETA LE TTT 17 FLASH PICTURES You can make pictures at night in full color or black and white with your Kodak Signet 35 Camera. All you need are the Kodak Flasholder, batteries, and lamps. For color, use Kodachrome Film Type A. Attach the flasholder by screwing the bracket thumbscrew into the camera tripod socket. Remove the caP from the FLASH POST on the rim of the shutter. and attach the cord. Flashing the lamp is controlled by the synchro feature of the shutter. Use “C” size batteries (photoflash are best). They should test at least 5 amperes. The Kodak B-C Flashpack can be used instead of the “C” size batteries. The Flash- pack and a 22%-volt photoflash battery will Caution: Since lamps may shatter when flashed, the use of a Kodak 2-Way Flashguard or other shield over the reflector is recommended. Do not flash the lamps in an explosive atmosphere. Do not insert flash lamps in the reflector if the shutter is open — the lamp may flash and a serious burn may result. 18 make a battery-condenser unit out of your Kodak Flasholder at a nominal cost. It provides long battery life and trouble-free synchronization—see page 33. Use Class M (No. 5 or 25) flash lamps only. These lamps can be used at all shutter speeds. Class F flash lamps (SM or SF) should not be used. Be sure the bottom of the lamp base is clean and bright before inserting the lamp in the flasholder. If the contact point is tarnished, rub it on a rough surface. 19 = РР це ГО Ш) = fi FLOOD PICTURES a — ET Practical, flexible home lighting is provided by flood lamps in suitable reflectors such as the Kodak Vari- Beam Lights. A good basic lighting is shown in the diagram. during the exposure. Use a tripod such as the Kodak Eye-Level Tripod or other firm support. To make a long exposure (the focus and lens open- ing having been set), set the shutter on “B.” Cock the shutter, Press the release and hold it down for the ; exposure required; then let the release spring back. Avoid jarring the camera. The Kodak TBI Metal Ca- ble Release No. 2 is useful for longer exposures. Sundown. dark davs, or dark interiors need not mark the end of picture taking, You can still make good pictures by using longer exposure or by using Hood or flash lamps. LONG EXPOSURES FOR STILL SUBJECTS The “B” setting on your shutter enables you to keep the shutter open for as long as required. Excellent night pictures can be made by using long exposures. Many novel pictures are made by the reflection of lighted buildings or monuments on wet pavement or fireworks, fireside scenes, ete, Both camera and subject must be still 99 al md striking when a little EER QT forethought goes into their composition. 0 Salhouetles can be wor Pra bY vel AN a | Note: To advance the film when a cable release is used, press and hold the rewind lever (see page 7) and rotate the winding knob 4 turn; then release the lever and turn the knob until it locks. Reflections from wet pavements or bodies of water are spectacu- lar. Place your camera on a solid support or tripod, aim and hold the shutter open on "B" for the exposure required. In this case 30 seconds to 1 min- ute. 4 y E i Chri Ly MT TELA How could grandma be more characteristi- cally portrayed than with a flash shot like this? KODAK FILMS The Kodak Signet Camera uses Kodak 135 Film. Kodachrome Film — For superb color pictures. The film is processed, at no additional cost, at an Eastman Kodak Laboratory. The resulting transparencies are returned to you, mounted (unless otherwise specified) for projection or viewing. Kodacolor Prints and Enlarge- ments can be made from your Koda- chrome transparencies. Kodacolor Prints are attractive 34 x 5-inch full-color prints with white borders. Kodacolor Enlargements can be supplied in sizes 5 x 7 and B x 10. The first Kodacolor Print from each transparency is moder- ately priced and there is a great sav- ing on all following prints. Kodacolor Prints and Enlargements must be or- dered through your Kodak dealer, Use Kodachrome Film Daylight Type for daylight pictures and Kodachrome Film Type À for flood or flash pictures. 20 or 36 exposures. To select transparencies for printing, hold each one at an angle near a sheet 24 of white paper which is illuminated by a tungsten light. Any transparency which has been carefully exposed under good picture-taking conditions will appear attractive when viewed in this manner. In general, transparencies of this type will produce pleasing prints, Don't choose a slide for a color print because it looks good when being projected in a darkened room. You'll be viewing your Kodacolor Prints and Enlargements in a lighted room, so it's wise to select your slides as mentioned above. Choose only transparencies which are (1) clear and sharp, and (2) evenly lighted—not con- trasty. Kodak Plus-X Panchromatic Film — An excellent film for general outdoor and well-lighted interior use. The low graini- ness and high resolving power permit high-quality enlargements. 20 or 36 exposures. Kodak Super-XX Panchromatic Film — A very high-speed film for use when the light is poor. Especially valuable for use with artificial light. 20 or 36 exposures. 25 for better pictures Y Tell a Story Look Beyond the Subject Whatever the background, make sure that it is a set- ting or frame for your picture, not an intruding ele- ment in the composition. Look beyond the subject; The best pictures are those which tell a simple story and tell it at a glance. You'll treasure pictures of day-to-day ac- tivities around the home, perhaps including some entirely unposed ones, But whatever the subject, a moment spent in ex- pressing an idea will re- pay you many times in satisfaction with your fin- ished prints. your camera does. Side and Back Lighting Pictures in which the light comes from the side of the scene often give a feeling of depth. Shadows across the foreground make you feel that you are looking into the picture. With either side or back lighting it is important to shield the lens from direct light by keeping it in the shade, or by using the Kodak Lens Hood (see page 29). ACCESSORIES A Kodak Leather Car- rying Case of top grain leather protects your camera and per- mits it to be ready at a moments notice. The screw in the base of the case screws into the tripod socket of the camera. The exposure guide on the camera is visible when the front flap is down. You can leave the adapt- er ring and filter on and still close the case. Cable Releases — Two releases are available for your Kodak Signet 35 Camera: the Kodak TBI Metal Cable Release No. 2, which simplifies the making of time exposures, and the Kodak Metal Cable Release No. 5. To attach a cable release, screw the release into the 28 hole in the shutter housing, under the trip lever. Kodak Eye-Level Tripod —This sturdy aluminum tripod provides a rigid and dependable support for your camera. Folded, it measures 22% inches; extended, 60 inches. The use of the Kodak Turn-Tilt Tripod Head (an accessory) is recom- mended for maximum facility in changing the position of the camera on the tripod. Kodak Combination Lens Attachments — Series V Lens Attachments are used with this camera, The basis of the combination is the Series V, No. 22, screw-in type or 1%-inch slip-on type Kodak Adapter Ring. Kodak E: eZ me NE o de = SN a E an me E 4 5. 29 Wratten Filters, Portra Lenses 24+ and 3+, Pola- Screen, and Lens Hood are available in this series. If you use a Pola-Screen in combination with another attachment such as a filter, use a Series V-VI Step-up Ring and a Series VI Pola-Screen. To assemble a filter or lens in the ring, unscrew and remove the insert, place the filter or lens in the ring, and replace the insert. The Kodak Lens Hood can be used in place of the insert. Filters add greatly to the pictorial effects of black-and- white pictures by darkening the sky and recording the clouds. The Kodak Wratten Filters K-2, G or A can be used for this purpose. These result in medium, strong, and extra-strong effects respectively. Never use these strongly colored filters with Kodachrome Film. With Kodachrome Film use a Kodak Pola- Screen to darken the sky, Filters for Kodachrome Film — Kodachrome pictures made in open shade under a clear blue sky, or on over- cast or hazy days will be improved if a Kodak Skylight Filter is used. Kodachrome Film Type A can be used for daylight exposures with the Kodak Daylight Filter for Kodak Type A Color Films. For flash photography with Kodachrome Film, Kodak Light Balancing Filters No. 81C with No. 5 flash lamps and No. 81D with No. 25 flash lamps are recommended for best color rendering. 30 KODAK PORTRA LENS 3 + KODAK PORTRA LENS 2 + Approx. Field Size Based on Kodak Readymount Opening (inches) Subject (inches) Distance Comera Lens Setting—| to Lens* Feet Approx. Field Size Based on Kodak Readymount Opening (inches) *Subject-to-lens distance is measured to front of the Portra Lens Distance Subject to Lens* (inches) Camera Lens Setting — Feet *Subject-to-lens distance is measured to front of the Fortra Lens Kodaslide Merit Projector—You get big-picture projec- tion and even illumination with the Kodaslide Merit Projector. An f/3.5 Lumenized Kodak Projection Ektanon Lens, new, unique slide-feeding mechanism, built-in elevation device—all these combine to make your scenes live again in brilliant coloring, Kodaslide Table Viewer 4X—This new viewer pro- vides complete one-package projection for your 35mm transparencies. Your slides are enlarged over 4 times and brilliantly illuminated by the Lumenized optics without fuss or bother in a normally lighted room. The Kodak Projection Ektanon 50mm f/3.5 Lens projects the image to the special daylight type view- ing screen. It is easily transported and only needs plugging into a 100- to 125-volt, a-¢ or d-c¢ line to be instantly ready for use. If you wish the added fea- ture of a slide changer, the Kodaslide Table Viewer Model A should be your choice, It will accept 75 ready mounts or 30 dou- ble-glass slides. Your slides are enlarged nearly 5 times. The Kodak B-C Flashpack offers a battery-condenser method of flashing lamps. It provides more than enough energy for accurate synchronization and de- pendable lamp firing. In addition, you'll be able to use the same battery for a year or more. Ask your dealer to show you one today. The Kodak Standard Flash- older is a new, lightweight yet rugged unit that ac- cepts midget flash lamps. It is powered by two "C” cells or a Kodak B-C Flashpack. A decal on the reflector gives instant ex- posure information. The bracket is designed to hold the flasholder rigidly for accurate aiming or to per- | | mit rapid removal for off- | the-camera work. = ER No y T are Mara ">
/
Download
Just a friendly reminder. You can view the document right here. But most importantly, our AI has already read it. It can explain complex things in simple terms, answer your questions in any language, and help you quickly navigate even the longest or most compilcated documents.
Advertisement