Annonce
Annonce
WILSONWERKS
ARCHIVES
This camera manual 1s for reference and historical purposes, all rights reserved.
This cover page is copyrighted material. This document may not be sold or
distributed without the express consent of the publisher.
©2008 wilsonwerks Llc
KODAK B-C FLASHOLDER
THE KoDAK B-C FI.ASHOLDER 185 a newly designed unit that can be
used to supplement sunlight or to serve as the main light source.
It can be used with any camera having a flash shutter and a standard
hayonet flash connector, or a camera having a continental flash shutter
equipped with a Kodak Flashpost Adapter. The outfit consists of a
Lumiclad reflector, battery case, 15-inch cord, camera bracket, and
Kodak 2-Way Flashguard. A table on the reflector gives easy-to-use
exposure information for Kodak films with various lamps. Get a
224-volt battery to power the unit. The lamp socket accepts midget-
type flash lamps.
Here's how the B-C (battery-condenser) circuit works. The battery
does not fire the lamp directly; rather, it supplies current to the con-
denser. The condenser acts as a storage reservoir. When the shutter is
tripped, a single, intense surge of current is supplied by the condenser
to the lamp. The condenser 1s then recharged by the battery. With your
B-C unit, disappointing flash failures due to weak batteries will be a
thing of the past. | |
This system offers many advantages over the use of a battery alone.
They are:
1. The peaking time of the lamp is more consistent.
2. In most cases the battery life will be its shelf life. This means
one year or more of flash work with one battery.
3. More dependable firing of extension units is assured.
4. The lamps will fire easily in cold winter weather.
5. Since the battery supplies current only to the condenser, even a
weak battery will charge the condenser. You will get the same syn-
chronization for the entire life of the battery.
Attach the Kodak B-C Flasholder to
the camera with the mounting
bracket. Select the proper hole in KODAK B-C FLASHOLDER
the bracket and fasten the bracket WITH KODAK TOURIST Ii
to the camera by screwing the CAMERA
thumbscrew into the camera tripod
socket. On some cameras when a
field case is used, the black washer
should be removed.
Once attached to your camera,
the Kodak B-C Flasholder serves as
a handy press-type grip.
T.M. Reg. U.S, Pat. Off
Now read the following instructions to make sure that you fully
understand your equipment—then you will be ready for new adventure
in photography.
POWER
The Kodak B-C Flasholder uses a 22%-volt battery of the type used
in miniature radios and electronic equipment. À battery is not supplied
with your Flasholder, but must be purchased from your dealer. Typical
batteries are: Eveready Mini-Max Photoflash #412; Olin X 0915;
Burgess Battery U15E; General Dry Batteries Inc. ¥ 612.
To install the battery in the Flasholder, remove the back from the
handle by loosening the screw. Then place the battery in the Flasholder
with the positive (+) terminal of the battery next to the condenser
marked “Battery +.” The negative ( —) terminal of the battery should
rest on the spring clip in the bottom of the battery case. The battery
should be left in the unit at all times.
Caution: Short battery life will result if the battery is installed in a reversed
position, that is, with the positive end down.
ATTACHING
The camera bracket has several holes to permit the selection of the one
most suitable for your camera. To attach the bracket to the camera,
select the proper hole, insert the thumbscrew (with the black washer)
in the hole, and screw it into the tripod socket in the camera.
After the bracket has been attached to the camera, screw the Flash-
older to the bracket. Aim the reflector so that it covers the same field
as seen through the view finder. Then, tighten the screw. You will get
better pictures if the bracket is attached so that the center of the
reflector will be higher than the camera lens. Remember, if the flash
lamp 1s below the camera lens, the lighting effect on faces will be
unnatural.
KODAK B-C FLASHOLDER
WITH KODAK SIGNET
35 CAMERA
KODAK B-C FLASHOLDER
WITH KODAK PONY 828
CAMERA
mes
CONNECTIONS
Connect the cord directly to the flash terminal* on the shutter or
camera. To make the connection, place the bayonet connector on the
cord over the terminal, push it in, and turn it to the right. To remove
the connector, push it in, turn 1t to the left, and pull it off the terminal.
When connecting the cord, make sure that it does not fall in front of
the camera lens.
FLASH LAMPS
Your Flasholder is designed to use any of the standard midget-type
flash lamps, such as SM, SF, Nos. 5, 5B, 25, and 25B. Before using any
lamp, make sure that the base is clean and bright; if tarnished, rub the
base on the rough surface provided by the edge of the thumbscrew.
To insert the lamp, place the two pins on the base of the lamp in the
slots in the socket—then push the lamp straight into the socket. Do
not twist the lamp! |
To release the lamp from the socket, push the LAMP RELEASE spring
located on the top of the Flasholder. The lamp will fall from the socket.
Caution: Do not insert a flash lamp in the socket if the shutter is set on
ET? and the shutter blades are open, or if the end of the cord is plugged into the
extension terminal on the front of the handle. The lamp will flash and a serious
burn may be the result.
Flash lamps are too hot to handle after they have been fired, there-
fore, never try to pull a lamp out of the socket. Always use the lamp
release because pulling lamps out by force may damage the socket.
KODAK FLASH SHUTTERS
Three types of Kodak flash shutters have been made: (1) with syn-
chronizer lever and scale nut, (2) with synchronizer lever and without
scale nut, (3) without synchronizer lever or scale nut.
Those with scale nuts must be pre-
set for the class of lamp being used.
Shutters without scale nuts require
no presetting, but a slightly different
procedure 1s followed for each class
of lamp.
*The use of the accessory Kodak Flashpost
Adapter (for Flash Compur, Pronto, and
Prontor Shutters) is necessary with most
continental shutters. To install the adapt-
er, slip the open end over the flash termi-
nal of the shutter and press it on firmly.
The exposed end of the adapter accepts the
bayonet connector on the Flasholder cord.
Flash Shutters with Synchronizer Lever
and Scale Nut
The synchronizer scale on the shutter has
two positions: F for Class F lamps, such as the SM or SF flash lamp;
and M for Class M lamps, such as the No. 5 or No. 25 flash lamp.
To insure accurate synchronization, the scale must be set at the
correct position.
To set the scale, loosen the SCALE NUT with a small screwdriver, shift
the scale so that the proper letter is opposite the arrow, and tighten
the nut securely. On some shutters the scale nut 1s of the plunger type
SYNCHRONIZER LEVER
and no screwdriver is needed. Once the scale has been set, do not
change it as long as lamps of the same class are used.
To Take Flash Pictures (Scale Nut Shutter)
After the Flasholder has been connected to the camera, insert a flash
lamp in the socket. Push the lamp straight in, without twisting it.
Before taking the picture, cock the shutter * in the usual way. Then
cock the sYNCHRONIZER LEVER by pushing it toward the synchronizer
scale as far as it will go. The synchronizer lever must always be cocked, or
the flash will not be synchronized.
Flash Shutters with Synchronizer Lever and without Scale Nut
In Kodak flash shutters without a scale nut, the synchronizing interval
for Class F lamps, such as the SM or SF flash lamp, is automatically
controlled by the action of the shutter blades—the synchronizer lever is
not used. When the synchronizer lever is used, the shutter is synchronized
with Class M lamps, such as the No. 5 or No. 25 flash lamp.
Class F lamps will not synchronize consistently with Kodamatic or
Supermatic Shutters without scale nuts at speeds faster than 1/100
second. However, with flash lamps, the exposure time 1s limited by
the duration of the flash which, in the case of SM or SF flash lamps, is
about 1/200 second. Thus, shutter speeds of 1/100 second or longer
with SM or SF flash lamps result in an exposure of 1/200 second—
short enough to stop all motion normally encountered.
*On some Kodak cameras the shutter is automatically cocked as the film is
advanced.
5
To Take Flash Pictures (Shutter with Synchronizer Lever but without
Scale Nut)
With Class IF lamps, such as SM or SF flash lamps:
1. Insert the lamp in the socket. .
2. Cock the shutter in the usual way. a
3. Release the shutter. Do not use the synchronizer lever.
With Class M lamps, such as No. 5 or No. 25 flash lamps:
1. Insert the lamp in the socket. |
2. Cock the shutter in the usual way. ™
3. Press the synchronizer lever clockwise as far as it will go.
4. Release the shutter.
Flash Shutters without Scale Nut or Synchronizer Lever
Flash Kodon Shutter:
With Class M lamps, set shutter at “B.”
With Class IF lamps, set shutter at “I.”
Kodak Flash Dakon, Flash Diomatic, and Flash 200 Shutters:
With Class M lamps, set shutter at 1/25, “T,” or “B.”
With Class F lamps, set shutter at 1/25, 1/50, or 1/100.
EXPOSUKE
Always consult your camera manual for specific information that may apply to
making flash pict: res with your camera.
To find the correct exposure, select from the table on page 7 the
exposure guide number for the film, lamp, and shutter speed. Divide
this number by the distance in feet from the lamp to the subject. The
answer is the recommended lens opening. |
For example, the exposure guide number for the SM or SF flash
lamp at 1/100 second with Kodak Super-XX Film is 110. At 10 feet
(lamp-to-subject distance), 110 divided by 10=11 or //11; at 5 feet,
110 divided by 5 =22 or f/22, etc.
The table on the reflector gives the lamp-to-subject distance in feet
for the various lens openings, with an exposure time of 1/25 second.
*On some Kodak cameras the shutter is automatically cocked as the film 1s
advanced. |
6
FLASH LAMP EXPOSURE GUIDE NUMBERS FOR KODAK FILMS
AND ONE FLASH LAMP NEAR THE CAMERA
Lamp SM or SF No. 5 or 25
Shutter Speed E 1/100 | 1/200 LA 1/50 | 1/100 | 1/200
Kodak Verichrome Film 75 70 1 60 140 120 100 80
Kodak Plus-X Film ‚ 85 75 1470 150 | 140 120 0%
Kodak Super-XX Film 120 110 | 100 | 220 200 170 130
Kodacolor Film Type A 60 55 50 110 | 100 85 65
Kodachrome Film Type A 551 50f| 451 80* | -70*| 60*| 45*
Rada Ektachrome Film Type B 60f| 553) 4541 35%
TSatisfactory results can be obtained without a filter. For best color rendering with the SF lamp,
use a Kodak Light Balancing Filter No. 81A.
*With No. 5 lamp, use Kodak Light Balancing Filter No. 81C. With No. 25 lamp, use Kodak
Light Balancing Filter No: 81D.
{With Kodak Light Balancing Filter No. 81C.
BLUE COATED FLASH LAMP EXPOSURE GUIDE NUMBERS FOR
KODAK COLOR FILMS, DAYLIGHT TYPE
- (For use indoors without daylight)
Lamp No. 5B or 25B
o B to |
Shutter Speed 5 1/50 | 1/100 (1/200
| | 1/25
Kodachrome Film Daylight Type 50 45 40 30
Kodacolor Film Daylight Type 80 70 60 45
Kodak Ektachrome Film Daylight Type 45 40 35 26
The flash guide numbers mentioned in your camera manual may
differ from the numbers on this page. This is because the Lumiclad
reflector throws more light than satin-finished reflectors. For best
results, always use these guide numbers or the decal on the reflector.
Caution: Since lamps may shatter when flashed, the use of a Kodak 2-Way
Flashguard over the reflector is recommended. The Flashguard is packed with
the Flasholder. Do not flash the lamps in an explosive atmosphere.
VARY YOUR LIGHTING
Most of your flash photography will probably be done at home
where you will be taking pictures of your family and friends. Birth-
days, holidays, and parties are but a few of the special events that you
should photograph. There’s nothing ‘quite like a picture record to help
you relive happy times. |
Because so many of your pictures will be of people, 1t's wise to con-
sider the different types of lighting that can be used. The illustrations
and diagrams show what can be done using one and two lights.
Four pictures and how they were made
1. On-the-camera Lighting—Flasholder at camera. 2. Off-the-camera Lighting—Flasholder with
3-foot Extension Cord.
These are but a few of the lighting setups that can be used. You will
probably be able to think of many more.
When the Flasholder is mounted on the camera, you will get even
lighting. While this is satisfactory for the average flash shot, more
modeling light is usually needed for pictures of people. Study the
pictures to see the effects of varied lighting.
Get a Kodak Flasholder 3-foot Extension Cord, Bayonet Connector,
to increase modeling. This cord, which fits between the Flasholder
cord and the shutter terminal, permits you to hold the Flasholder away
3. Extension for Accent Lighting—Flasholder at 4. Extension for Modeled Lighting— Flasholder
camera and Extension Unit far around to the side. at camera with Extension Unit at 45 degrees.
from and about two feet higher than the camera. Compare pictures
1 and 2.
Another useful accessory to the B-C Flasholder is the Kodak
Flasholder Extension Unit. The Extension Unit has a 20-foot cord and
a handy “C” clamp bracket. The 20-foot cord enables you to move
the second light away from the camera. In this way you will be able
to accent certain areas of the picture, improve roundness of the sub-
ject, and bring out texture. The “CC” clamp bracket serves as a “third”
hand, for the padded clamp can be fastened to any round or flat
surface up to two inches thick. Furniture, doors, etc., can be used as
light stands. The clamp can also be screwed onto a tripod. Complete
instructions are packed with the Extension Unit. Now look at pictures
3 and 4. The Extension Unit has been used for both of these.
The off-the-camera lighting (2) makes the subject stand out from
the background. As a rule, it is best to hold the Flasholder away from
the camera so that it will throw light in the direction toward which the
subject 1s facing.
In pictures 3 and 4, the Extension Unit is used in addition to the
light at the camera. The effect of the second lamp depends upon where
you place it in respect to the subject-to-camera axis.
With extension for accent lighting (3), the lamp is placed far around
to the side (almost at right angles to the camera axis). Here, it accents
the hair and cheek of the subject. For story-telling pictures, place this
light so that it creates a strong emphasis on the most important story-
telling element of the picture. This is why it is so widely used in maga-
zine and newspaper work.
With extension for modeled lighting (4), the Extension Unit is used
more conservatively, that is, it is not placed so far around to the side.
In this case the line between the Extension Unit and the subject makes
an angle of about 45 degrees with the camera axis. Hold the extension
high enough to throw a shadow of the nose downward, leaving a tri-
angular patch of highlight on the cheek. When you take a picture in
this manner, you will give a sense of roundness to the subject.
The relative distances of the extension lamp and the camera light
will determine the lighting contrast. At equal distances, they will
produce excellent results in color. For more dramatic effects in color
and black-and-white, an extension-light distance of about two-thirds
that of the camera-light distance is recommended.
10
SUPPLEMENTARY FLASH FOR OUTDOOR COLOR PICTURES
With bright sunlight and a clear blue sky, the contrast of the day-
light is frequently too high to permit best results on color films, particu-
larly with nearby side- or back-lighted subjects. No. 5B or No. 25B flash
lamps provide a convenient means of illuminating shadow areas with
light approximating daylight in color quality. Thus the lighting contrast
between highlights and shadows can be reduced to a more suitable ratio
for color pictures. Use a No. 5B or No. 25B flash lamp 5 to 10 feet from
the subject.
SUPPLEMENTARY FLASH TABLE
For Use in Bright Sunlight with Front or Side Lighting
Set Shutter at 1/25 Second
Kodacolor Film Daylight Type 1/16
Kodachrome Film Daylight Type Between f/8 and f/11
Kodak Ektachrome Film Daylight Type 1/8
EASTMAN KODAK COMPANY « ROCHESTER 4, N.Y.
6-52-KP-HX Printed in the United States of America
a
o a
e
qu
Ferté
">
/
Download
Bare en venlig påmindelse. Du kan se dokumentet lige her. Men vigtigst af alt har vores AI allerede læst det. Den kan forklare komplekse ting i enkle vendinger, besvare dine spørgsmål på ethvert sprog og hjælpe dig med hurtigt at navigere selv de længste eller mest komplicerede dokumenter.
Annonce