Smart SDC-450 User`s guide
Below you will find brief information for Document Camera 450. This guide helps you set up and utilize your new document camera to transform any learning environment into an interactive space. Learn to display documents, objects, and microscope slides, capture images and videos, and integrate with SMART Notebook software for dynamic presentations, including manipulating 3D models with the mixed reality cube.
Advertisement
Advertisement
SMART Document
Camera™ 450
User’s guide
Product registration
If you register your SMART product, we’ll notify you of new features and software upgrades.
Register online at smarttech.com/registration .
Keep the following information available in case you need to contact SMART Support.
Serial number:
Date of purchase:
FCC warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Trademark notice
SMART Document Camera, SMART Board, SMART Notebook, SMART Exchange, smarttech, the SMART logo and all SMART taglines are trademarks or registered trademarks of SMART Technologies ULC in the U.S. and/or other countries. Google 3D Warehouse and SketchUp are trademarks of Google Inc. Adobe, Reader and
Acrobat are registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. Windows is either a registered trademark or trademark of Microsoft Corporation in the U.S. and/or other countries. Mac and OS X are trademarks of Apple Inc., registered in the U.S. and other countries. All other thirdparty product and company names may be trademarks of their respective owners.
Copyright notice
© 2012 SMART Technologies ULC. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language in any form by any means without the prior written consent of SMART Technologies ULC. Information in this manual is subject to change without notice and does not represent a commitment on the part of SMART.
This product and/or use thereof covered by one or more of the following U.S. patents.
www.smarttech.com/patents
01/2013
i
Important information
W A R N I N G l
Failure to follow the installation instructions shipped with your SMART product could result in personal injury and damage to the product.
l
Ensure that any cables extending across the floor to your SMART product are properly bundled and marked to avoid a trip hazard.
l
To reduce the risk of fire or electric shock, do not expose the SMART product to rain or moisture.
l
Do not push foreign objects into the openings on your SMART product.
l
Do not open or disassemble the SMART product. You risk electrical shock from the high voltage inside the casing. Opening the casing also voids your warranty.
l
The camera arm on your SMART product has joints that present a pinch hazard when you move the camera arm. Keep clear of the pinch points.
l
Do not stare into the light or shine the light directly into someone’s eyes. Turn off the light when displaying or capturing images of people.
l
Do not overload power outlets or extension cords as this can result in a fire or electric shock.
l
Turn off and disconnect your SMART product before a thunderstorm. During a thunderstorm, do not touch your SMART product or the power plug, because there is a risk of electrical shock.
l
Only use your SMART product with the type of power source that is written on the power supply and do not modify the plug.
C A U T I O N l
Place your SMART product on a solid surface to prevent it from falling.
l
If you have a security cable attached to our SMART product, do not carry or swing your
SMART product by the security cable.
I M P O R T A N T I N F O R M A T I O N l
Do not connect non-shielded interface cables to your SMART product and do no leave cables connected to unused connectors, because this can cause interference levels that exceed
FCC regulations.
l
Avoid setting up and using the SMART product in an area with excessive levels of dust, humidity and smoke.
l
Do not block or cover the openings or slots on your SMART product. These slots provide ventilation, ensure reliable operation and protect your SMART product from overheating.
l
Do not carry your SMART product by the camera arm. Carry it by the base of the unit.
l
Do not aim the camera lens at the sun.
l
If your SMART product requires replacement parts, make sure the service technician uses replacement parts specified by SMART Technologies or parts with the same characteristics as the original.
ii
iii
Contents
Chapter 2: Setting up your SMART Document Camera
Setting up your document camera
Connecting your document camera to different displays
Turning you document camera on and off
Connecting your document camera to external devices
Shooting area, overhead light and anti-glare sheet
Chapter 3: Using your SMART Document Camera
Understanding Camera, Computer Pass-Through and Playback modes
Identifying features of each mode
Inserting and removing an SD/SDHC card
Chapter 4: Using your SMART Document Camera in Camera mode
Using the on-screen display (OSD) menu in Camera mode
Capturing and transferring images and videos
Chapter 5: Using your SMART Document Camera with SMART Notebook software
Using your document camera with SMART Notebook software
Chapter 6: Using your SMART Document Camera in Playback mode
Setting your document camera to Playback mode
C O N T E N T S
Using the Playback mode on-screen display (OSD) menu
Deleting images in Playback mode
Chapter 7: Using 3D Tools for SMART Notebook software and Mixed Reality Tools
Incorporating 3D content into your lessons
Getting started with Mixed Reality Tools for SMART Document Camera
Inserting and manipulating 3D models
Using Mixed Reality Tools for SMART Document Camera
Using SketchUp sketching software and Trimble 3D Warehouse
Appendix A: Hardware environmental compliance
Waste Electrical and Electronic Equipment regulations (WEEE directive)
Restriction of Certain Hazardous Substances (RoHS directive)
iv
Chapter 1:
1
Chapter 1
Overview
Adjustable camera arm and camera head
SMART Notebook software and SMART Product Drivers
Introduction
Your document camera 450 can transform any classroom or lecture hall into a spontaneous and interactive learning environment. It uses a high-resolution video camera to display clear and detailed images of written material or any physical object.
2
C H A P T E R 1
Overview
Your SMART Document Camera™ 450 enables you to display printed documents, microscope slides and 3D objects on your computer, projector or television. You can record videos, scan documents, capture images and save them to a SMART Notebook™ collaborative learning software file or to an
SD/SDHC card or USB drive.
Your document camera integrates with SMART Notebook software and SMART Board® interactive whiteboards, creating an interactive presentation environment.
You can use the mixed reality cube with your document camera to manipulate 3D models in
SMART Notebook files.
Document camera features
Camera
l
High resolution 5 MP CMOS sensor l
8× optical zoom, 8× digital zoom l
Internal memory l
Up to 30 frames per second l
Automatic or manual focus l
Maximum shooting area 15 3/4" × 11 3/4" (40 cm × 30 cm) l
Microphone integrated into base l
Microscope mode that requires adapters
Output/input
l
VGA and DVI-I outputs XGA (1024 × 768), SXGA (1280 × 1024), 720p (1280 × 720), 1080p (1920
× 1080) l
Composite video output with user-selectable NTSC or PAL formats l
RGB (VGA) input (when selected by the user) is a pass-through to the VGA output.
Physical construction
l
Security lock slot l
Flexible arm l
Bright LED overhead light
3
C H A P T E R 1
Overview
Software
l
SMART Notebook software 11 or later, including 3D Tools for SMART Notebook software and
Mixed Reality Tools software.
l
SMART Product Drivers
Image and video storage
l
Supports SD/SDHC cards with a built-in card slot (up to 32 GB, speed glass 4).
l
Supports USB drivers.
l
Supports USB mass storage mode for internal memory and SD card when connected to a computer.
Parts of the document camera
Adjustable camera arm and camera head
You can fold and adjust the flexible arm to position the lens at any angle. The camera head has a bright LED overhead light to enhance the lighting condition.
1 Camera head
2 Camera lens
3 Overhead light
4 Flexible arm
5 Control panel
Control panel
You can use the control panel to switch between Camera, Computer Pass-Through and Playback modes. You can also use it to control features and settings in the Camera mode's on-screen display menu.
C H A P T E R 1
Overview
Button
1 Select/Enter
2 Menu
3 Record video
4 Power on/off
7 Select playback
8 Overhead light on/off
9 Image brightness
10 Zoom in/out
5 Select camera 11 Auto-focus
6 Select computer pass-through 12 Capture to SMART Notebook software or to local memory
13 USB indicator: computer or USB drive
For information on the different modes, see Understanding Camera, Computer Pass-Through and
4
5
C H A P T E R 1
Overview
Rear connection panel
The rear connection panel has DC 12V 2A, VGA In, VGA Out, Composite Video Out and USB mini-B connectors.
1 Connect the power cable
2 Connect a VGA output connector of a computer
3 Connect any display device with a VGA cable
4 Connect the supplied composite video adapter cable
5 Connect a USB connector of a computer
Left-side connection panel
The left-side connection panel has a DVI output, a switch for selecting either a computer or a USB drive, and audio in and out connect.
1 Connect any display device with a DVI cable
2 USB switch
3 Connect a USB drive
4 Connect an external microphone
5 Connect speakers for video playback only
6
C H A P T E R 1
Overview
Right-side connection panel
The right-side connection panel has an SD/SDHC card slot, a switch for selecting VGA-DVI or composite video output and a security lock slot.
1 Camera head storage
2 SD/SDHC card slot
3 TV/VGA switch
4 Security lock slot
Bottom control panel
The NTSC/PAL switch is on the bottom control panel. This switch enables you to change the format of the composite video output for your television. Changes to the selected video output take effect the next time you turn on your document camera. The resolution reset button resets the output VGA/DVI resolution to XGA.
N O T E
You can press the resolution reset button with a pen tip. Pressing the button for three seconds resets the output VGA/DVI resolution to 1024 × 768.
C H A P T E R 1
Overview
7
1
2
NTSC/PAL switch
Resolution reset button
Mixed reality cube
With a mixed reality cube, you can interact with 3D models in SMART Notebook software using
Power supply
Your document camera comes with a power supply, including a country-specific connector that connects to the external power supply. Plug adapters for North America, Great Britain, Europe and
Australia are provided.
USB cable
Use the USB cable to connect your document camera to your computer. You can display objects, capture images to SMART Notebook files and control your document camera from SMART Notebook software.
VGA cable
Use the VGA cable to connect your document camera to a computer, projector or display. You can display objects and capture images and videos to a storage device.
8
C H A P T E R 1
Overview
Composite video adapter cable
Use the composite video adapter cable to connect your document camera to a projector or a display.
You can display objects, capture images and videos to a storage device and use the features in the on-screen menus.
N O T E
The provided DB9 connector isn’t needed in any of the connection configurations.
Microscope adapter
Your document camera comes with a microscope adapter and two different sized rubber couplers to fit the microscope eyepiece. With a microscope you can examine microscopic objects on a big screen.
Anti-glare sheet
Place the anti-glare sheet over printed documents to reduce glare.
Document camera modes
Your document camera has three modes you can use to control how it sends data to a computer, projector, monitor or television.
l
Camera mode controls your document camera from its control panel and displays images on a projector, monitor or television.
l
Computer Pass-Through mode displays the image from the VGA input on a projector, monitor or television connected to the VGA output.
l
Playback mode controls your document camera from its control panel and displays images from an SD/SDHC card or USB drive on a connected projector, monitor or television.
See Understanding Camera, Computer Pass-Through and Playback modes on page 23 for more
information on these modes.
9
C H A P T E R 1
Overview
Document camera software
Your document camera includes software downloads that you need to present images from your document camera.
SMART Notebook software and SMART Product Drivers
Your document camera uses SMART Notebook software and SMART Product Drivers.
SMART Notebook software is presentation software designed to work with
SMART Document Cameras and the touch features of SMART Board interactive whiteboards. In addition, with a mixed reality cube, you can manipulate 3D models in SMART Notebook files using
Mixed Reality Collaboration tools (see Using 3D Tools for SMART Notebook software and Mixed
You can find system requirements for your computer in the SMART Notebook software 11.1 release
notes ( smarttech.com/kb/170138 ).
I M P O R T A N T
You need to have SMART Notebook software 11 SP1 or later installed on your computer before you connect your document camera.
Downloading software
To install SMART Notebook software and SMART Product Drivers
1. Go to smarttech.com/software.
2. Scroll to SMART Notebook collaborative learning software.
3. Click Choose a version, select the latest version of SMART Notebook software for Windows® or Mac, and then follow the on-screen instructions.
Chapter 2:
11
Chapter 2
Setting up your
SMART Document Camera
Setting up your document camera
Connecting your document camera to different displays
Connecting your document camera to a monitor or a projector
Connecting your document camera to a monitor or a projector with a DVI interface
Connecting your document camera to a TV or a projector
Turning you document camera on and off
Connecting your document camera to external devices
Connecting your document camera to a microscope
Switching between VGA, DVI and composite output
Connecting your document camera to an external microphone
Connecting your document camera to speakers
Shooting area, overhead light and anti-glare sheet
Introduction
This chapter explains how to set up your document camera and how to connect with different displays and devices. It also explains external memory storage usage.
C H A P T E R 2
Setting up your SMART Document Camera
Setting up your document camera
The document camera has a flexible arm with rotational movement for easy positioning display objects.
To unfold and position your document camera
1. Place a hand on the base of the document camera to stabilize it.
2. Press the camera head down, and then pull the camera arm outward and upward.
3. Move the camera head to aim the lens at your object.
I M P O R T A N T
To use your document camera with SMART Notebook software you need to connect your document camera to a computer.
12
C H A P T E R 2
Setting up your SMART Document Camera
To connect the power supply
1. Connect the power supply cable to the DC 12V receptacle on the rear connection panel.
2. Connect a country-specific connector to the power supply.
3.
C A U T I O N
Ensure you connect the power connector to the power supply before connecting the power plug to a power outlet.
4. Connect the plug to a power outlet.
To use your document camera in Camera or Playback mode, connect your document camera directly to an external display.
To connect your document camera to a computer with a USB cable
1. Set the USB switch on the left side connection panel to .
The indicator on the control panel lights up, and you can use your document camera as a
USB camera or to transfer captured pictures/videos from the memory source to your computer.
2. Connect a USB cable to the USB receptacle on the rear connection panel.
3. Locate the USB connector on your computer, and then connect the cable to it.
To connect your document camera to a computer with a VGA cable
1. Connect a VGA cable to the VGA In receptacle on the rear connection panel.
2. Locate the VGA Out connector on your computer, and then connect the cable to it.
Connecting your document camera to different displays
After you complete the basic connection procedure, you can connect your document camera to an external display. This enables you to use the document camera in Camera mode and Playback mode
(see page 23) and to access the on-screen display menu for those modes.
13
C H A P T E R 2
Setting up your SMART Document Camera
You can connect your document camera directly to an external display to enable the following functions: l
Use Camera mode to view the camera image in full-screen on the external display.
l
Use Playback mode to view a full-screen slide show on the external display.
I M P O R T A N T
To use your document camera with SMART Notebook software you need to connect your document camera to a computer.
Setting the TV/VGA switch
The TV/VGA switch determines the display output selection. Set it to VGA (right)
VGA or DVI connection for a signal output. Set it to TV (left) a composite output.
when using a when using an RCA connection for
Connecting your document camera to a monitor or a projector
In this configuration your document camera is connected to your external display device with a VGA cable.
To connect your document camera to a monitor or a projector
1. Complete the basic connection steps (see page 12).
I M P O R T A N T
Make sure the TV/VGA switch is set to VGA .
2. Connect a VGA cable to your document camera's VGA Out receptacle and your display device's VGA In connector .
Connecting your document camera to a monitor or a projector with a DVI interface
In this configuration your document camera is connected to your external display device with a DVI cable (not supplied).
14
C H A P T E R 2
Setting up your SMART Document Camera
To connect your document camera to a monitor or a projector with a DVI interface
1. Complete the basic connection steps (see page 12).
I M P O R T A N T
Make sure the TV/VGA switch is set to VGA .
2. Connect a DVI cable to your document camera's DVI Out receptacle and your monitor's or projector’s DVI Input connector.
3. Connect your document camera to an external display with a VGA cable (see page 16).
This configuration makes it easy to transition from Computer Pass-Through mode to Camera mode or Playback mode using the same projector or display for all three modes.
Connecting your document camera to a TV or a projector
In this configuration your document camera is connected to your computer with both a composite video adapter cable and an RCA cable.
To connect your document camera to a TV or a projector
1. Complete the basic connection steps (see page 12).
2. Connect a composite video adapter cable to your document camera's Composite Video receptacle.
3. Connect an RCA cable to your display's Video In connector.
4. Connect the composite video adapter and the RCA cables (see page 16).
I M P O R T A N T
Do not connect the 9-pin cable
DVI or composite video displays will not display your computer view. A VGA display is required.
15
C H A P T E R 2
Setting up your SMART Document Camera
Turning you document camera on and off
To turn on your document camera
Press the power button on the control panel.
The power light changes from amber to flashing green. When the light is solid green, your document camera is operational.
To turn off your document camera
Press the power button on the control panel.
The power light changes from green to amber.
Connecting your document camera to external devices
You can connect your document camera directly to the following external devices: l
Microscope l
Microphone l
Speakers
Connecting your document camera to a microscope
You can connect your document camera to a microscope. This enables you to examine microscopic objects on a big screen.
To set up a microscope
1. Select the appropriate rubber coupler size for the microscope eyepiece and insert it in the microscope adapter.
16
C H A P T E R 2
Setting up your SMART Document Camera
2. Attach the microscope adapter to your document camera's camera head, and then connect it to your document camera.
3. Tighten the three bolts until the adapter secures the eyepiece.
4. Fit the camera head with the microscope adapter over the microscope's eyepiece.
I M P O R T A N T
Make sure the arrow on the camera head and microscope adapter are on the same side.
5. Turn the microscope adapter counterclockwise to line up the arrows and lock the microscope adapter in place.
17
C H A P T E R 2
Setting up your SMART Document Camera
To connect the microscope to a projector or a display
1. Press the button on the control panel, and then select the tab.
2. Use the control panel.
button on the control panel to select MODE, and then press the
3. Use the control panel.
button on the control panel to select , and then press the button on the button on the
4. Press the button on the control panel to close the menu.
5. Connect the other end of the VGA cable to the VGA In connector on your projector or display.
6. Set the VGA/TV switch on the right-side connection panel to VGA .
Switching between VGA, DVI and composite output
If you’re using a projector or a computer display with a VGA or a DVI cable, set your document camera to the VGA mode. If you’re using a television with the composite video cable, set your document camera to the TV mode
To set your document camera to the VGA mode
Set the VGA/TV switch on the right-side connection panel to VGA
To set your document camera to the TV mode
Set the VGA/TV switch on the right-side connection panel to TV .
.
Connecting your document camera to an external microphone
You can connect an external microphone to your document camera.
N O T E S l
The built-in microphone on the control panel is disabled when an external microphone is connected.
l
The audio is in monophonic sound.
18
C H A P T E R 2
Setting up your SMART Document Camera
To connect an external microphone to your document camera
Connect the microphone's cable to the microphone on your document camera's left-side connection panel.
Connecting your document camera to speakers
You can connect speakers to your document camera. Only audio from the video playback is supported.
C A U T I O N
Turn the volume down to prevent hearing damage when using earphones.
To connect speakers
Connect the speakers’ 3.5 mm cable to the speaker receptacle on your document camera's leftside connection panel.
Shooting area, overhead light and anti-glare sheet
Shooting area
The shooting area can view a maximum area of 15 3/4" × 11 3/4" (40 cm × 30 cm).
To rotate the image
1. Press the
2. Press the button on the control panel.
button on the control panel, and then select button on the control panel.
.
3. Press the
4. Press the
5. Press the button on the control panel, and then select ROTATE.
button on the control panel.
6. Select rotation range, and then press the button on the control panel.
7. Press the button on the control panel to close the menu.
19
C H A P T E R 2
Setting up your SMART Document Camera
To mirror the image
1. Press the
2. Press the button on the control panel.
button on the control panel, and then select button on the control panel.
.
3. Press the
4. Press the
5. Press the button on the control panel, and then select MIRROR.
button on the control panel.
6. Select ON or OFF, and then press the button on the control panel.
7. Press the button on the control panel to close the menu.
Overhead light
Press the button on your document camera's control panel to turn the overhead light on or off.
Anti-glare sheet
The anti-glare sheet is a special coated film that helps eliminate any glare that could be encountered while displaying glossy objects, such as magazines and photos. Place the anti-glare sheet on top of the object to reduce reflected light.
20
C H A P T E R 2
Setting up your SMART Document Camera
External memory storage
Your document camera supports both an SD/SDHC card and a USB drive for image capture, audio and video recordings. Your document camera detects when an external storage device is connected and automatically switches to the last detected storage. If no external storage device is connected, all captured images are saved in the built-in memory.
I M P O R T A N T
Your document camera comes with piece of plastic inserted in the SD card slot. Remove this piece of plastic before you insert your SD/SDHC card.
N O T E S l
Your document camera supports SD/SDHC cards with up to 32 GB, speed class 10.
l
SDHC card with class-6 or higher is recommended for high-quality recording.
l
Push in the SD/SDHC card to eject it.
To connect a USB drive
1. Set the USB switch on the left-side connection panel to
Your document camera detects the USB drive and the lights up.
2. Insert the USB drive into the USB receptacle.
N O T E S
Your document camera supports USB drives with up to 64 GB.
.
indicator on the control panel
21
Chapter 3:
23
Chapter 3
Using your
SMART Document Camera
Understanding Camera, Computer Pass-Through and Playback modes
Identifying features of each mode
Inserting and removing an SD/SDHC card
Introduction
This chapter provides information about your document camera's different modes.
Understanding Camera, Computer Pass-
Through and Playback modes
You can use your document camera in Camera, Computer Pass-Through or Playback mode. Each mode enables you to complete different functions and requires a specific connection to either a display, a projector or a computer.
Camera mode
In Camera mode, you can view document camera images only in SMART Notebook software.
Camera mode allows connection over USB and live image output. You can view full-screen images from your document camera using a projector or high-definition display without a computer.
C H A P T E R 3
Using your SMART Document Camera
You can save images to your SMART Notebook file to present them later, or if your computer is connected to an interactive whiteboard, projector or television, you can deliver your
SMART Notebook presentation with live images from your document camera.
N O T E
The Capture button on the control panel saves the image to the Notebook page and closes the
SMART Document Camera window. Pressing the Capture button again will re-open the
SMART Document Camera window.
You can use the Camera mode’s on-screen display menu for greater control of the image.
See Using your SMART Document Camera in Camera mode on page 31.
Computer Pass-Through mode
Computer Pass-Through mode switches your document camera's video output to the VGA input. You can switch between the live camera image and your computer screen image.
You can view the document camera live image only in SMART Notebook software.
N O T E S l
Capture button on the control panel has no effect in Computer Pass-Through mode.
l
In Computer Pass-Through mode, you can only view the document camera live image in
SMART Notebook software.
Playback mode
In Playback mode you can view full-screen images and slide shows from the memory card on a projector or high-definition display without a computer. You can’t use your document camera as a mass storage device in Playback mode.
24
C H A P T E R 3
Using your SMART Document Camera
Identifying features of each mode
The following table describes the differences between each mode.
Feature description Camera mode
Computer
Pass-Through mode
Playback mode
View computer input (VGA In) No
View document camera image Yes
View pictures from a memory card No
Access an internal memory and SD/SDHC card from the computer with a USB cable
Yes
[1]
Control the document camera from a computer
Capture to SMART Notebook software
Capture to an SD/SDHC memory card
Access the related on-screen display menu
Capture to a USB drive
Yes
Yes
Yes
Yes
Yes
[2]
Yes (VGA out and
DVI analog)
No
No
No
Yes
[1]
No
Yes
No
Yes
[1]
No
No
No
No
No
No
No
Yes
No
N O T E S l
[1] Only when the USB switch is set to l
[2] Only when the USB switch is set to
. See The Setting tab on page 39.
. See The Setting tab on page 39.
The following table describes outputs when your document camera is connected to a display with
VGA, DVI or Composite Video Out.
Feature description Camera mode
Computer
Pass-Through mode
Playback mode
Connect to a projector or display (VGA out and DVI analog output)
Camera image
VGA In Memory card images
25
C H A P T E R 3
Using your SMART Document Camera
Feature description Camera mode
Computer
Pass-Through mode
Connect to a DVI digital output projector or a display
Camera image
Connect to a television (composite video out)
Camera image
N/A
N/A
Playback mode
Memory card images
Memory card images
Setting document camera modes
To set your document camera to Camera mode
1. Set your document camera to Computer mode using the switch on the left-side connection panel. The USB indicator on the control panel displays .
2. Connect your document camera to your computer with the USB cable.
3. Set the TV/VGA switch on the right-side connection panel to VGA .
4. Connect your document camera to a projector, monitor or television with a VGA cable.
5. Press the button on the control panel.
To set your document camera to Computer Pass-Through mode
1. Connect your document camera to your computer with the USB cable.
2. Connect your computer with the VGA cable to your document camera's VGA In receptacle.
3. Connect your display device with another VGA cable to your document camera's VGA Out receptacle.
4. Press the button on the control panel.
26
C H A P T E R 3
Using your SMART Document Camera
To set your document camera to Playback mode
1. Disconnect the USB cable from the rear connection panel.
2. Connect your document camera to a projector or a monitor with the VGA cable or to a television with the composite video adapter cable if needed.
3. Press the button on the control panel.
Displaying printed documents
When you set your document camera to Camera mode, you can display printed documents, use the anti-glare sheet to reduce glare, and optimize the image for text and graphic documents with the
Image mode options.
To display printed documents
1. Place your documents on the table.
2. Adjust the document camera, and then aim its lens at your documents.
3. Press the button on the control panel to adjust the focus.
To reduce glare
If glare makes it difficult for you to read the printed documents that you’re displaying, place the anti-glare sheet on top of the printed documents.
To optimize the image for text documents
1. Set your document camera to Camera mode.
2. Press the button on the control panel.
The on-screen display menu appears.
3. Press the control panel.
button on the control panel to select , and then press the button on the
4. Press the button on the control panel to select IMAGE MODE, and then press the button on the control panel.
27
C H A P T E R 3
Using your SMART Document Camera
5. Press the control panel.
button on the control panel to select , and then press the
See The Image tab on page 34 for an explanation of the settings.
button on the
To optimize the image for documents with graphics
1. Set your document camera to Camera mode.
2. Press the button on the control panel.
The on-screen display menu appears.
3. Press the control panel.
button on the control panel to select , and then press the button on the
4. Press the button on the control panel to select IMAGE MODE, and the press the button on the control panel.
5. Press the control panel.
button on the control panel to select , and then press the
See The Image tab on page 34 for an explanation of the settings.
button on the
Inserting and removing an SD/SDHC card
Your document camera has an SD/SDHC card slot on the right-side connection panel. You can save document camera images to an SD/SDHC card when your document camera is in Camera or
Computer Pass-Through mode. When your document camera is in Playback mode you can display previously captured images from an SD/SDHC card.
C A U T I O N
Avoid static electricity near a card because it can damage.
I M P O R T A N T
Your document camera comes with a piece of plastic inserted in the SD/SDHC card slot. Remove this piece of plastic before you insert your SD/SDHC card.
28
C H A P T E R 3
Using your SMART Document Camera
To insert an SD/SDHC card
1. Press the button on the control panel.
2. Insert an SD/SDHC card into the card slot on the right-side connection panel with the contact facing down.
I M P O R T A N T l
You might need to set your document camera to use the SD/SDHC card as the storage
location (see The Setting tab on page 39).
l
Ensure the label on the SD/SDHC card is facing up.
To remove an SD/SDHC card
C A U T I O N
To prevent memory card damage, do not remove the memory card while capturing or deleting images.
1. Press the image.
button on the control panel and wait until your document camera displays a live
2. Push in the card to eject it, and then remove the card.
29
Chapter 4:
Chapter 4
Using your
SMART Document Camera in
Camera mode
Using the on-screen display (OSD) menu in Camera mode
Using the Picture in Picture (PiP) feature
Capturing and transferring images and videos
Transferring images to your computer
Introduction
This chapter explains how to use your document camera in Camera mode.
Using Camera mode
When your SMART Document Camera is connected to a projector, flat-panel display or television you can display a full-screen image from your document camera.
You can use your document camera in Camera mode to perform the following tasks: l
Display objects.
l
Capture images to an SD/SDHC card.
l
Capture images to SMART Notebook.
31
C H A P T E R 4
Using your SMART Document Camera in Camera mode l
Use the features and settings in the on-screen display menu.
l
Use a microscope with a standard eyepiece with additional adapters.
I M P O R T A N T
Your document camera must be connected directly to an external display when using the OSD
menu. See Connecting your document camera to external devices on page 16.
To switch to Camera mode
1. Connect your document camera to a projector or flat-panel display with the appropriate cable
(see Connecting your document camera to external devices on page 16).
2. Press the button on the control panel.
To display objects
1. Press the button on the control panel.
2. Place the object you want to display under the camera.
3. Rotate the camera head to aim the lens at your object.
To adjust the zoom magnification
Press the button on the control panel.
To automatically adjust the focus
Press the button on the control panel.
To adjust brightness settings
Press the button on the control panel.
To record a video
1. Insert an SD/SDHC card or USB drive into the appropriate receptacle.
2. Press the
3. Press the button on the control panel to start recording.
button on the control panel to stop recording.
32
C H A P T E R 4
Using your SMART Document Camera in Camera mode
Using the on-screen display (OSD) menu in
Camera mode
There are four tabs on the OSD menu: Image, Presentation, Setting and System. Use the OSD menu to adjust settings for your document camera in Camera mode.
To navigate the OSD menu and submenus
1. Set your document camera to Camera mode.
2. Press the button on the control panel.
The OSD menu appears.
3. Press the
4. Press the
5. Press the
6. Press the
7. Press the and and buttons on the control panel to toggle between tabs.
buttons on the control panel to choose a selection in the menu list.
button on the control panel to make a selection.
button on the control panel to enter a submenu.
button on the control panel to return to the previous menu level.
8. Press the button on the control panel to exit the menu.
The following OSD menu options are available when your document camera is in Camera mode.
Tab
Image
Presentation
Settings
System
Options
Brightness, Contrast, Mode, Effect, Mirror, Advanced, Focus, Rotate.
See The Image tab on the next page.
Picture in Picture (PiP), Split Screen, Timer. See The Presentation tab on page 36.
Capture, Recording, Storage, Format, USB to PC and Flicker.
Language, Output Display, Backup, Save Setting, Recall Setting,
Information, Default.
33
C H A P T E R 4
Using your SMART Document Camera in Camera mode
The Image tab
To access the Image settings menu
1. Press the button on the control panel.
2. Press the button on the control panel.
3. Press the control panel.
button on the control panel to select , and then press the
4. Press the or on the control panel.
button on the control panel to select button on the
, and then press the button
34
Image options
Brightness
Contrast
Description
Adjust the image brightness manually.
Adjust the image contrast.
C H A P T E R 4
Using your SMART Document Camera in Camera mode
Image options
Mode
Effect
Mirror
Advanced o o o
Auto Image
Exposure
White Balance
Focus
Rotate
Description
Select an option from five image settings: o Sharp – adjust the contrast to make text appear more visible o
Graphics – adjust the image gradient o Motion – increase the frame rate (sufficient lighting is required when using this setting) o
Macro – set when viewing an object that is close to the camera, no more than 7 3/4" (20 cm) away from the camera o
Infinite – set when viewing an object that is more than
22" (55 cm) away from the camera
Convert the image to color, black/white or film negative image.
Select to flip the image: o o
OFF – displays a normal image
ON – displays a mirrored image
Select to automatically adjust white balance and exposure, and to correct color and exposure compensation.
Select the exposure setting: o o
AUTO – automatically adjust the camera exposure
MANUAL – manually adjust the camera exposure
Select the white balance setting for various light conditions: o
AUTO – automatically adjust the white balance o MANUAL – manually adjust the red and blue color levels up to 255.
Adjust the focus manually.
o o o o
OFF – displays normal image rotation
90° – rotates the image 90°
180° – rotates the image 180°
270° – rotates the image 270°
35
C H A P T E R 4
Using your SMART Document Camera in Camera mode
The Presentation tab
Presentation features enable you to show previously captured images along with the live camera view. These features aren't available when the document camera is connected as a USB camera.
To access the Presentation tab
1. Press the button on the control panel.
2. Press the button on the control panel.
3. Press the control panel.
button on the control panel to select
4. Press the control panel.
button on the control panel to select
, and then press the button on the
, and then press the button on the
36
C H A P T E R 4
Using your SMART Document Camera in Camera mode
Presentation options
Picture in Picture (PiP)
Description o Shows captured pictures or video as thumbnails in corner of the screen in Camera mode.
37
Split Screen o Press the left and right navigation buttons to navigate through the stored images.
o Press the button to cancel PiP.
o o o
Divides the screen in two parts.
Half of the screen displays thumbnail images and the other half displays the image from your document camera.
Select the display location: left, right, top, bottom.
o Press the left/right and up/down navigation buttons to highlight the image.
o
Press the button to select the image.
o Press the left/right and up/down navigation buttons to pan the stored image.
C H A P T E R 4
Using your SMART Document Camera in Camera mode
Presentation options
Timer
Description o
Press the o
N O T E button to cancel split screen.
You can’t capture an image while in Split Screen mode.
o Provides an on-screen countdown timer for a presenter to assist with presentation time management.
Using the Picture in Picture (PiP) feature
The PiP feature allows you to display an image from stored memory within the live camera image.
This is useful for showing before and after comparisons.
N O T E
The PiP feature is for display purposes only. You can’t capture an image while in PiP mode.
To display the PiP image
1. Display an object in Camera mode, and then press the
The OSD menu appears.
button on the control panel.
2. Press the control panel.
button on the control panel to select , and then press the
3. Press the control panel.
button on the control panel to select PiP, and then press the button on the button on the
38
C H A P T E R 4
Using your SMART Document Camera in Camera mode
4. Select the corner of the display, and then press the button on the control panel.
Your document camera displays a picture in picture image.
5. Press and
The Setting tab
buttons on the control panel to choose different stored images.
To access the Setting tab
1. Press the button on the control panel.
2. Press the button on the control panel.
3. Press the control panel.
button on the control panel to select
4. Press the control panel.
button on the control panel to select
, and then press the
, and then press the button on the button on the
39
C H A P T E R 4
Using your SMART Document Camera in Camera mode
40
Settings options
Capture o Resolution o Quality o Type o Interval
Recording
Storage
Format
USB to PC
Description
Select image capture size. In 5M setting, the capture resolution is 2592 × 1944.
Select image quality; Finest, High, Normal.
Select image capture type: o o
Single – capture one picture at a time
Continuous – capture consecutive pictures
Set the time interval for continuous capture. The length can be set up to 600 sec (10 min).
Select the video recording compression setting.
Change the storage location: o Audio and video recording can be saved only on an
SD/SDHC card, or a USB drive.
Delete all the data in the selected memory.
Select the status of your document camera when it’s connected to the computer using a USB cable. Make sure the USB switch on the left-side connection panel is set to
.
o o
Camera – can be used as a computer webcam, to capture still images or to record a video
Storage – transfer captured images or videos from the memory to a computer hard drive
C H A P T E R 4
Using your SMART Document Camera in Camera mode
Settings options
Flicker
Description
Select refresh rate: o o
50 Hz – sets frequency to 50 Hz
60 Hz – sets frequency to 60 Hz
Playback mode
Playback mode sets how your document camera, computer and a memory card interact.
To access the Playback mode
1. Press the button on the control panel.
2. Press the button on the control panel.
3. Press the control panel.
button on the control panel to select , and then press the button on the
4. Press the button on the control panel to select USB to PC, and then press the on the control panel.
5. Select STORAGE, and then press the button on the control panel.
Action
See the memory card from your computer
View and use your document camera from SMART Notebook software
Capture image to the memory card in both Computer Pass-
Through and Camera modes
No
Storage
Yes
No button
Camera
No
Yes
Yes
This mode enables you to see the contents of your USB drive or SD memory card from your computer.
The mass storage mode enables you to see the contents of the embedded memory or SD/SDHC card from your computer. They will show up as removable disks. Look in the document camera DCIM directories for the stored images and videos.”
41
C H A P T E R 4
Using your SMART Document Camera in Camera mode
The System tab
To access the System menu
1. Connect your document camera to a projector, flat-panel display or television (see page 16).
2. Press the button on the control panel.
3. Press the button on the control panel.
The OSD menu appears.
4. Press the control panel.
button on the control panel to select , and then press the button on the
42
System options
Language
Description
Select or change the language: o o o o
English
Français
Deutsch
Español
C H A P T E R 4
Using your SMART Document Camera in Camera mode
System options
Output Display
Backup
Save Settings
Recall Settings
Information
Default
Description
Set the resolution to display an image on the screen: o o o o
1024 × 768
1280 × 1024
1280 × 720
1920 × 1080
N O T E
This selection disabled in TV output mode.
o o
SD/SDHC – copy images and presentations from the build-in memory to an SD/SDHC card
USB drive – copy images and presentations from the build-in memory to a USB drive
Save the current setting in the selected profile number.
N O T E
Only effect, mode, brightness and contrast settings can be saved.
Restore the setting to the selected profile number.
Display the product information.
Restore all the settings to the factory default settings.
Capturing and transferring images and videos
You can capture images and videos from your document camera to an SD/SDHC card or USB drive and transfer them to a computer.
Capturing images
You can capture images and videos to an SD/SDHC card or USB drive when your document camera is in Camera mode.
To capture images to memory
1. Set your document camera to Camera mode. See Using Camera mode on page 31.
2. Position your document camera.
3. Adjust any camera settings using the Camera mode’s OSD menu. See Using Camera mode on
43
C H A P T E R 4
Using your SMART Document Camera in Camera mode
4. Press the button on the control panel.
To record a video using an SD/SDHC card
1. Insert an SD/SDHC card in your document camera's SD/SDHC card slot.
2. Press the control panel.
button on the control panel to select
3. Press the to select STORAGE, and then press the
The document camera detects the SD/SDHC card.
, and then press the button on the button on the control panel.
4. Press the
2.
N O T E button on the control panel to start recording.
The video saves in .AVI format in your SD/SDHC card.
5. Press the button on the control panel to stop recording.
To record a video using a USB drive
1. Insert a USB drive in your document camera’s USB receptacle.
2. Press the to select STORAGE, and then press the
The document camera detects the USB drive.
button on the control panel.
3. Press the
2.
N O T E button on the control panel to start recording.
The video saves in .AVI format in your USB drive.
3. Press the button on the control panel to stop recording.
Transferring images to your computer
You can transfer images from your external storage device to your computer.
44
C H A P T E R 4
Using your SMART Document Camera in Camera mode
To transfer images to your computer
1. Use the OSD menu to set your document camera USB to PC mode to STORAGE.
2. Connect your document camera to your computer with the USB cable (see Setting up your
Your computer recognizes your document camera and the external storage device as a removable disk.
3. Browse to the removable disk on your computer, and then transfer the images to your computer.
Using a microscope
You can view the microscope stage through the document camera using additional attachments. See
Connecting your document camera to external devices on page 16.
To display a microscope slide
1. Place a slide or object on the stage of the microscope.
2. Focus the microscope so that the subject is in sharp focus.
3. Position the microscope under your document camera so the camera lens is aligned with the microscope eyepiece.
C A U T I O N
Ensure you do not hit your document camera lens with the microscope. This could damage your document camera’s lens.
4. Press the button on the control panel.
5. Press the button on the control panel.
6. Press the control panel.
button on the control panel to select , and then press the
7. Press the control panel.
button on the control panel to select MODE, and then press the button on the button on the
8. Press the control panel.
button on the control panel to select , and then press the button on the
45
Chapter 5:
Chapter 5
Using your
SMART Document Camera with
SMART Notebook software
Using your document camera with SMART Notebook software 47
Using your document camera with
SMART Notebook software
You can display objects and capture an image to a SMART Notebook page.
You can present images from your document camera through SMART Notebook software. The interactive whiteboard or projector displays your computer desktop or SMART Notebook file.
I M P O R T A N T
Your document camera should be in Camera mode. SMART Notebook software also works with
the camera in the Computer Pass-Through mode. See The Setting tab on page 39.
N O T E
For information on using 3D Tools for SMART Notebook software and Mixed Reality Tools for
SMART Document Camera, see Using 3D Tools for SMART Notebook software and Mixed
To open a SMART Document Camera window
1. Connect your SMART Document Camera to your computer and turn on the document camera.
2. Start SMART Notebook software.
3. Press SMART Document Camera on the SMART Notebook menu bar.
A SMART Document Camera window appears.
47
C H A P T E R 5
Using your SMART Document Camera with SMART Notebook software
4. Place the object or objects you want to display under the camera.
5. Press any of the following on the menu bar to adjust the image.
Menu option Description
Zoom out.
Zoom in.
Decrease brightness.
Increase brightness.
Focus automatically.
Focus out manually.
Focus in manually.
Change the appearance of the image: rotate it 180º, define the image color, black and white or film negative. You can also start and stop Microscope mode and start Mixed Reality Tools for SMART Document Camera automatically.
Start Mixed Reality.
Insert a screen capture on the current page and then close the window.
Capture an image and insert a screen capture on a new page and keep the current window open.
48
C H A P T E R 5
Using your SMART Document Camera with SMART Notebook software
To take a series of screen captures
1. Open a SMART Document Camera window.
2. Press Capture with Time-Lapse on the SMART Document Camera window menu bar, and then select a period of time. (For example, if you want to take a screen capture every 15 seconds, select 15 Seconds.)
3. When you’re done, press to stop recording.
N O T E
The display appears in the bottom left corner of your SMART Notebook page. It displays the time that has lapsed since the last screen capture and the number of screen captures taken.
To use a microscope
1. Connect your document camera to a microscope. See Connecting your document camera to
2. Open a SMART Document Camera window.
3. Press Additional Settings on the SMART Document Camera window menu bar, and then select Start Microscope Mode.
N O T E
The Additional Settings button doesn’t appear if you’re using a
SMART Document Camera 230 with SMART Notebook software.
4. Press Additional Settings , and then select Stop Microscope Mode when you’re done.
49
Chapter 6:
51
Chapter 6
Using your
SMART Document Camera in
Playback mode
Setting your document camera to Playback mode
Using the Playback mode on-screen display (OSD) menu
Playback mode OSD menu options
Deleting images in Playback mode
Introduction
This chapter explains how you can use your document camera in Playback mode. When you set your document camera to Playback mode, you can play back images from the SD/SDHC card, USB drive or internal memory. You can browse through the stored images and display previously captured images either individually or as a slide show.
N O T E
In this mode your document camera can’t be connected by a USB cable and you must have images stored in either internal or external memory source.
Setting your document camera to Playback mode
Playback mode takes over the video output of the document camera. Live images and USB functions are not available during this time.
To set Playback mode using an SD/SDHC card
1. Connect your document camera directly to a projector or another display. For connection
C H A P T E R 6
Using your SMART Document Camera in Playback mode
2. Insert an SD/SDHC card in your document camera.
3. Press the button on the control panel.
To set Playback mode using a USB drive
1. Connect your document camera directly to a projector or another display. For connection
2. Set the USB switch to . The USB indicator on the control panel is lit.
3. Press the button on the control panel.
Using the Playback mode on-screen display
(OSD) menu
The Playback mode OSD menu shows the source storage location and controls how stored images are displayed.
Playback mode OSD menu options
To access the Playback mode OSD menu
1. Connect your document camera directly to a projector or another display. For connection
2. Set the USB switch to
OR
. The USB indicator on the control panel is lit.
Disconnect the computer USB connection to change the memory location to the USB drive.
3. Press the button on the control panel.
52
C H A P T E R 6
Using your SMART Document Camera in Playback mode
Playback mode OSD menu
Playback menu option
Slide Show
Interval
Effect
Current Storage
Delete All
Description
Displays all captured still images in an automated slide show.
Sets the slide show interval (in 5 second increments) before displaying the next image. The maximum interval is 100 sec.
Selects the slide show transition effect: o o o o o
Slide image
Checker down
Wipe down
Split vertical out
Split horizontal in
Chooses the storage source if more than one is available. Detects the storage source if only one is available.
Permanently deletes all the data in the selected memory source.
N O T E
A warning message appears. Select YES to continue or NO to stop.
To select the settings for a slide show
1. Press the button on the control panel to access the Playback mode OSD menu.
2. Press the and buttons on the control panel to make a selection, and then press the button on the control panel.
53
C H A P T E R 6
Using your SMART Document Camera in Playback mode
3. Press the
4. Press the and buttons on the control panel to toggle between functions.
button on the control panel to make a selection.
5. Press the button on the control panel to close the menu.
Repeat steps 2–4 as needed.
To play a slide show
1. Connect your document camera directly to a projector or another display. For connection
2. Set the USB switch to
OR
. The USB indicator on the control panel is lit.
Insert an SD/SDHC card or a USB drive in the appropriate receptacle.
3. Press the button on the control panel.
Thumbnail images from the memory source are displayed.
4. Press the
5. Press the
6. Press the view.
button on the control panel.
button on the control panel twice to start the slide show.
button on the control panel to stop the slide show or to return to the thumbnails
54
C H A P T E R 6
Using your SMART Document Camera in Playback mode
To play a video
N O T E
In the thumbnails view, videos have a symbol in the top left corner of the thumbnail image.
1. Connect your document camera directly to a projector another display. For connection
2. Set the USB switch to . The USB indicator on the control panel is lit.
3. Insert an SD/SDHC card or a USB drive in the appropriate receptacle.
4. Press the button on the control panel.
Thumbnail images from the memory source are displayed.
5. Press the and buttons on the control panel to toggle between images.
55
C H A P T E R 6
Using your SMART Document Camera in Playback mode
6. Press the button on the control panel to select the video you want to play.
7.
N O T E
Press the
Press the
Press the button to pause your video.
or button to adjust the volume.
button to rewind and the button to fast-forward.
8. Press the button on the control panel to stop the video or to return back to thumbnails view.
Deleting images in Playback mode
You can delete all images at once from your document camera’s three memory sources using the
OSD menu, or you can delete only selected images.
56
C H A P T E R 6
Using your SMART Document Camera in Playback mode
To delete all images
I M P O R T A N T
You are unable to delete images from your computer in Playback mode. You can delete images only from the three memory sources.
1. Select the memory source you want to delete all the images from.
2. Press the button on the control panel to access the Playback mode OSD menu.
3. Press the button on the control panel to select DELETE ALL.
4. Press the selection.
button on the control panel, and then press the
The DELETE ALL warning appears.
button again to make a
5. Press the
6. Press the
7. Press the or button on the control panel to select YES or NO.
button on the control panel to DELETE or CANCEL.
button on the control panel again to close the Playback mode OSD menu.
N O T E
The deleting-image icon appears briefly while your document camera deletes images.
To delete selected image
1. Press the
2. Press the delete.
button on the control panel to display all the images in the memory storage.
or or or button on the control panel to select the image you want to
3. Press the button on the control panel.
The DELETE THIS IMAGE warning appears.
4. Press the
5. Press the or button on the control panel to select YES or NO.
button on the control panel to DELETE or CANCEL.
57
Chapter 7:
Chapter 7
Using 3D Tools for
SMART Notebook software and
Mixed Reality Tools
Incorporating 3D content into your lessons
Getting started with Mixed Reality Tools for SMART Document Camera
Activating 3D Tools for SMART Notebook software and Mixed Reality Tools
Hardware and software requirements
Inserting and manipulating 3D models
Pausing, playing and restarting animation
Using Mixed Reality Tools for SMART Document Camera
Manipulating 3D models using Mixed Reality Tools for SMART Document Camera
Disguising 3D models before presenting them
Using SketchUp sketching software and Trimble 3D Warehouse
Using SketchUp sketching software
Introduction
This chapter provides the information you need to begin using 3D Tools for SMART Notebook software and Mixed Reality Tools with your SMART Document Camera as well as SketchUp™ sketching software and Trimble® 3D Warehouse™ (formerly Google™ 3D Warehouse).
3D Tools for SMART Notebook software and Mixed Reality Tools provide an intuitive way for students and teachers to explore digital content with the document camera. This technology is integrated with SMART Notebook software.
59
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
3D Tools for SMART Notebook software and Mixed Reality Tools take this experience to a new level by providing teachers and students with a new way to engage with digital 3D content.
Incorporating 3D content into your lessons
You can incorporate 3D content into your SMART Notebook software lessons. The following are examples of how to do this: l
If you’re teaching a biology lesson, insert a 3D model of a heart into your .notebook file. Rotate and change the size of the 3D model to present the different parts of the heart.
l
If you’re teaching an English lesson, insert a 3D model of a city that is referenced in a novel the class is reading. Enter the 3D scene to navigate streets and interiors of buildings.
l
If you’re teaching a primary lesson, insert multiple 3D models and use the Disguise feature to reveal answers as a memory exercise.
Getting started with Mixed Reality Tools for
SMART Document Camera
Activating 3D Tools for SMART Notebook software and
Mixed Reality Tools
3D Tools for SMART Notebook software and Mixed Reality Tools provide an intuitive way for students and teachers to explore digital content with the SMART Document Camera.
When you connect your document camera to your computer, 3D Tools for SMART Notebook software and Mixed Reality Tools activate automatically. If you want to use 3D Tools for
SMART Notebook software on a computer that has never been connected to a document camera, you can activate 3D Tools for SMART Notebook software by obtaining a product key and following the procedure below.
N O T E
You can obtain a product key for 3D Tools for SMART Notebook software by registering your document camera’s serial number at smarttech.com/register .
To activate 3D Tools for SMART Notebook software
1. For Windows operating systems, select Start > All Programs > SMART Technologies >
SMART Tools > SMART Product Update.
60
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
For Mac OS X operating system software, browse to and double-click
Applications\SMART Technologies\SMART Tools\SMART Product Update.
The SMART Product Update window appears.
2. Click Activate in the SMART Notebook row.
The SMART Software Activation dialog box appears.
3. Click Add.
4. Type the product key you received from SMART in the Product Key box, and then click Add.
5. Click license agreement, review the license agreement, and then click Close.
6. If you accept the license agreement, select the I accept the terms in the license agreement check box.
7. Click Next.
3D Tools for SMART Notebook software activates.
8. Click Finish, and then close the SMART Product Update window.
Hardware and software requirements
To get started with Mixed Reality Tools for SMART Document Camera, you need the following: l
SMART Notebook software 11 SP1 l
SMART Document Camera 450 l
A mixed reality cube l
A computer meeting the requirements in the SMART Notebook software release notes
( smarttech.com/kb/170421 ).
61
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
Lighting requirements
Mixed Reality Tools works best in a bright room where the work surface doesn’t have any noticeable shadows or glare.
The light must be as uniform as possible, shining on the cube and background. You can achieve this by setting up the document camera so that the camera is facing directly down, perpendicular to a uniform, neutral work surface. The work surface should not be darker than the black elements on the mixed reality cube or lighter than the white elements on the cube.
N O T E S l
In very bright rooms, the work surface can appear whiter than the white elements on the cube.
l
To help increase the contrast between the cube elements and the background, and to increase the image frame rate, you can place a piece of white paper under the cube.
A typical projector room is usually quite dark. For Mixed Reality Tools to work properly, the document camera’s light should be turned on. Don’t manipulate the cube more than 14" (35 cm) from the document camera.
N O T E
If SMART Notebook software doesn’t enter Mixed Reality mode when you hold the cube under the camera, shake the cube under the camera. If the issue persists, press and hold the brighten button on the document camera to maximize the brightness.
Inserting and manipulating 3D models
To use 3D Tools for SMART Notebook software, you need to insert a 3D model in your .notebook file.
After you insert a 3D model, you can manipulate it in the same way you manipulate other objects in
SMART Notebook software.
N O T E
You can insert 2D images and 3D models on the same page and manipulate them the same way you manipulate other objects in SMART Notebook software.
62
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
Inserting 3D models
3D models are available from the 3D Objects folder in Lesson Activity Examples and the
SMART Exchange™ website ( exchange.smarttech.com
) as well as the Trimble 3D Warehouse (see
Using Trimble 3D Warehouse on page 73). You can also insert your own 3D models if they are in one
of the following formats: l
COLLADA (.dae) l
3D Object (.obj) l
FBX (.fbx)
N O T E
Textures and other information for some 3D models are stored in separate files and folders. When you insert these 3D models, ensure the 3D model file is located in the correct folder structure with the supporting files and folders.
To insert a 3D model
1. Select Insert > 3D File.
The Insert 3D File dialog box appears.
2. Browse to and select the 3D model you want to insert.
3. Press Open.
The 3D model appears on the page.
Manipulating 3D models
After inserting a 3D model, you can manipulate it in the same way you manipulate other objects in
SMART Notebook software. In particular, you can do the following: l
Cut, copy and paste l
Clone l
Move l
Scale l
Lock l
Attach links and sounds l
Add to the Gallery tab
63
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
N O T E S l
For information on these basic options, see the Help for SMART Notebook software.
l
When you add a 3D model to the Gallery tab, it appears in the 3D Objects category.
In addition to these basic options, you can do the following: l
Rotate the 3D model l
Pause, resume, play and restart animation l
Add labels
Rotating a 3D model
You can rotate a 3D model along multiple axes. After rotating a 3D model, you can reset it to its original orientation.
To rotate a 3D model along a single axis
1. Select the 3D model.
2. Press and hold one of the side rotation handles.
3. Drag your finger around the center of the 3D model, and then release your finger when done.
To rotate a 3D model along multiple axes
1. Select the 3D model.
2. Press and hold the center rotation handle.
3. Drag your finger in the direction you want to rotate the 3D model, and then release your finger when done.
To reset a 3D model to its original orientation
1. Select the 3D model.
2. Press the 3D model’s menu arrow, and then select Reset Rotation.
Pausing, playing and restarting animation
If a 3D model contains animation, you can pause, resume and restart the animation.
64
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
N O T E
If a 3D model doesn’t contain animation, the Animation menu documented in the following procedures is disabled.
To pause animation
1. Select the 3D model.
2. Press the 3D model’s menu arrow, and then select Animation > Play/Pause Animation.
To resume playing animation
1. Select the 3D model.
2. Press the 3D model’s menu arrow, and then select Animation > Play/Pause Animation.
To restart animation
1. Select the 3D model.
2. Press the 3D model’s menu arrow, and then select Animation > Restart Animation.
Adding labels
You can use labels to highlight different components of a 3D model. Labels can be text, shapes or other 2D objects.
To add a label
1. Select the 3D model.
2. Right-click the 3D model where you want to connect the label, and then select Add Label.
A label appears.
3. To use text in the label, double-click the label’s default text and then type your own text.
OR
To use a shape or other 2D object in the label, create the object and then drag it into the label.
4. Optionally, drag the label’s connection point to a different location on the 3D model.
To hide and display a label
1. Press the label’s connection point on the 3D model.
65
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
The label is hidden.
2. Press the label’s connection point to display the label.
To remove a label
1. Select the label.
2. Press Close .
Navigating 3D scenes
Large 3D models that contain internal details are called 3D scenes. You can navigate 3D scenes using controls in SMART Notebook software.
N O T E S l
You can use the navigation controls to navigate any 3D model. However, not all 3D models contain internal details. If you enter a 3D model that doesn’t contain internal details, the interior appears empty or dark.
l
If you’re using Mac OS X operating system software, you’re unable to enter a 3D scene while in Full Screen mode. To enter a 3D scene, first exit Full Screen mode and then complete the following procedure.
66
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
To navigate a 3D scene
1. Select a 3D model.
2. Press the 3D model’s menu arrow, and then select Enter 3D Scene.
SMART Notebook software displays the 3D scene in Full Screen mode. A map of the 3D scene, navigation controls and the Close button appear.
T I P S o You can press the gray border of the map to drag it to another area of the page if it’s covering materials you want to present. You can also resize the map by pressing and dragging the gray border in the lower-right corner.
o You can press the gray background or center icon of a navigation control to drag it to another area of the page if it’s covering materials you want to present.
67
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
3. Navigate the 3D scene using the navigation controls.
68
Button
G
H
E
F
I
J
C
D
A
B
Use to:
Change your orientation upward.
Change your orientation to the left.
Change your orientation to the right.
Change your orientation downward.
Raise elevation.
Move forward in the scene.
Move to the left in the scene.
Move to the right in the scene.
Move backward in the scene.
Lower elevation.
Alternatively, you can use keyboard buttons to navigate the 3D scene.
Keyboard button
D
S
W
A
Use to:
Change your orientation upward.
Change your orientation to the left.
Change your orientation to the right.
Change your orientation downward.
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
Keyboard button
PAGE UP
UP ARROW
LEFT ARROW
RIGHT ARROW
DOWN ARROW
PAGE DOWN
ESC
Use to:
Raise elevation.
Move forward in the scene.
Move to the left in the scene.
Move to the right in the scene.
Move backward in the scene.
Lower elevation.
Close
N O T E
As you navigate the 3D scene, a red indicator in the map displays where you are in the scene and the direction you are viewing. The arrow in the center indicates orientation. The arrow becomes a circle when you’re facing directly up or down.
Level Incline Decline
Off-screen (level)
4. Press Close when you’re done.
Upward Downward
Using Mixed Reality Tools for
SMART Document Camera
After inserting 3D models in your .notebook files using 3D Tools for SMART Notebook software, you can manipulate those models using Mixed Reality Tools for SMART Document Camera.
Manipulating 3D models using Mixed Reality Tools for
SMART Document Camera
You manipulate 3D models using your SMART Document Camera and the mixed reality cube.
69
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
To manipulate a 3D model using the mixed reality cube
1. Connect your SMART Document Camera to your computer and turn on the document camera.
2. Open the .notebook file, and then display the page containing the 3D model.
3. Place the mixed reality cube under the SMART Document Camera, showing one side of the cube to the camera.
SMART Notebook software enters Mixed Reality mode and assigns the 3D model to the cube. If there is more than one 3D model on the page, move the cube until the animation on the page indicates that the cube is connected to the 3D model you want to manipulate.
N O T E
SMART Notebook software enters Mixed Reality mode in this situation only if a 3D model is on the page. Alternatively, you can enter Mixed Reality mode by pressing SMART Document
Camera in the toolbar, and then pressing Start Mixed Reality in the
SMART Document Camera window.
70
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
4. Do any of the following: o To move the 3D model on the screen, move the cube.
o To rotate the 3D model on the screen, rotate the cube in your hand.
o To unassign the 3D model from the cube, cover the cube’s markings with your hand.
N O T E
If you experience any of the following symptoms, the cause may be issues with tracking: o The 3D model doesn’t connect to the cube.
o The 3D model shakes when it’s connected to the cube.
o The 3D model sporadically disconnects from the cube.
o SMART Notebook software enters Mixed Reality mode when the cube is under the camera even if you aren’t moving the cube.
To address tracking issues, see Lighting requirements on page 62.
T I P S o As you move and rotate the cube in your hand, ensure you don’t cover the symbols on the cube’s surface.
o To hide the image from the SMART Document Camera and show only the 3D model, move the transparency slider to the left.
5. If you’ve purchased a second cube from SMART and there is more than one 3D model on the page, manipulate another 3D model by completing steps 3 and 4 with the other cube.
N O T E
The two cubes must have different patterns if you want to use them both at the same time.
6. When you’re done, move the cube (or cubes) away from the camera.
SMART Notebook software exits Mixed Reality mode after a few seconds.
Disguising 3D models before presenting them
If you want to hide 3D models in your .notebook file before presenting them, you can use the Disguise feature to hide the 3D models with a magic hat.
When you use Mixed Reality Tools, the magic hat disappears after Mixed Reality Tools assigns the
3D model to the cube, revealing the 3D model.
71
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
N O T E
If you hide multiple 3D models on the same page with magic hats, each magic hat has a different colored ribbon.
To hide a 3D model with a magic hat
1. Select the 3D model.
2. Press the 3D model’s menu arrow, and then select Disguise > Disguised.
To change the magic hat’s color
1. Select the magic hat.
2. Press the magic hat’s menu arrow, and then select Disguise > Change Color.
To reveal a 3D model under a magic hat
Use Mixed Reality Tools as described in Manipulating 3D models using Mixed Reality Tools for
SMART Document Camera on page 69.
After Mixed Reality Tools assigns the 3D model to the cube, stars swirl around the magic hat, and then the magic hat disappears, revealing the 3D model behind it.
T I P
You can also reveal the 3D model by pressing the hat icon in the lower-left corner.
Using SketchUp sketching software and
Trimble 3D Warehouse
You can use the following 3D tools with 3D Tools for SMART Notebook software and Mixed Reality
Tools: l
SketchUp sketching software l
Trimble 3D Warehouse (formely Google 3D Warehouse)
72
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
Using SketchUp sketching software
You can use SketchUp sketching software to create 3D models. You can save these 3D models in
COLLADA (.dae) format and then insert them in SMART Notebook software.
To save a 3D model in .dae format
1. Open the 3D model in SketchUp sketching software.
2. Select File > Export > 3D Model.
The Export Model dialog box appears.
3. Browse to where you want to save the file.
4. Type a name for the file in the File name box.
5. Select COLLADA File (*.dae) in the Export type drop-down list.
6. Press Export.
To insert the 3D model in SMART Notebook software
See Inserting 3D models on page 63.
Using Trimble 3D Warehouse
Trimble 3D Warehouse (formerly Google 3D Warehouse) is an online repository of 3D models. Using this link in the SMART Notebook software Gallery tab, you can search for 3D models and download them to your computer. You can then insert the 3D models into your .notebook files.
To download 3D models
1. Press the Gallery tab.
2. Press Google 3D warehouse.
3. Search or browse for a 3D model that you want to download.
Select the model.
4. Press Download Model, and then press the Download link beside Collada (.zip).
N O T E S o When you first download a 3D model, you could be asked to provide a nickname.
o If you’re using Mac OS X operating system software and you cancel the download, the
3D model still saves to the Downloads folder.
73
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
5. Save the .zip file to your computer.
6. Extract the contents of the .zip file to a folder on your computer.
To insert a downloaded 3D model
See Inserting 3D models on page 63.
74
Chapter 8:
75
Chapter 8
Troubleshooting
This chapter includes troubleshooting information for your SMART Document Camera.
Document camera issues
Use the following table to troubleshoot issues with your document camera.
N O T E
These procedures vary depending on your version of Windows operating system and your system preferences.
Issue
The power light turns orange in standby mode.
Solution
Press the power turns green.
No camera image displays
(Camera mode).
button again to turn it on. The power light l l l l
Ensure your document camera is turned on.
Check all cable connections.
Check the TV/VGA switch on the right-side connection panel of your document camera and set it to the type of display device you have.
Reset the output resolution to 1024×768 by using a pen tip or other small object to press the resolution reset button on the bottom of the document camera.
No computer image displays
(Computer Pass-Through mode) l l l l l
Ensure your document camera is turned on.
Check all cable connections.
Check the cable connections from the computer VGA output to the VGA input of your document camera.
Ensure your document camera is in Computer Pass-Through mode.
On the some laptop computers, you can press FN+F5 repeatedly to toggle between display modes and the computer image on the presentation screen.
C H A P T E R 8
Troubleshooting
Issue
The presentation screen is dark and unreadable.
The image on the presentation screen is distorted or blurry.
SMART Notebook software doesn’t detect your document camera.
Solution l l l l l
Turn on Auto Image in your document camera’s on-screen display (OSD) menu (Menu > IMAGE > Advanced > Auto
Image) to adjust the image brightness..
Reset your document camera to its default settings (Menu >
SYSTEM > Default > Yes > Enter).
Make sure there’s enough light in the room, or turn on the overhead light on your document camera.
Adjust the brightness and contrast levels manually in the document camera's OSD menu, or use the control panel buttons.
If you are using a projector, check the bulb.
l l
Reset your document camera to its default settings (Menu >
SYSTEM > Default > Yes).
Adjust the brightness and contrast manually to reduce the distortion.
l
Press the out of focus.
button on the control panel if the image is blurry or l l l
Make sure your USB cable is connected.
Make sure the USB switch is set to .
Make sure your software is up-to-date (you should have at least
SMART Notebook software 11 SP1).
l l
Make sure the USB cable and the computer USB receptacle are working properly.
Make sure the USB to PC setting is set to CAMERA in the document camera's OSD menu.
SMART Notebook software enters Mixed Reality mode unexpectedly.
l
Press SMART Document Camera in the toolbar.
l
Press Additional Settings , and then clear the selection of
Automatically Start Mixed Reality Tools.
1.
N O T E
To enable the automatic detection of Mixed Reality again, press Additional Settings , and then select
Automatically Start Mixed Reality Tools.
76
C H A P T E R 8
Troubleshooting
Issue
No image appears when you press the button.
Your document camera doesn't detect the inserted
USB drive.
You're unable to record a video (the red recording light doesn’t turn on).
The SD/SDHC card or USB drive doesn't play video properly, or the document camera stops responding during video recording.
Solution l
Insert an SD/SDHC card or USB drive with stored images, or capture an image to the embedded memory.
1.
N O T E
Images need to be stored in the available memory location in order to enter Playback mode.
.
l
Disconnect the USB cable or set the USB switch to
Ensure the USB switch is set to .
l
Ensure an SD/SDHC card or USB drive is installed.
l
Disconnect the USB cable (the document camera doesn't record video while being used as a USB camera or mass storage device).
Format the SD/SDHC card or USB drive using the document camera's OSD menu (Menu > SETTING > Format > SD
CARD / USB DRIVE).
1.
C A U T I O N
This erases all the data on the SD/SDHC or USB drive.
Your document camera has an issue not described above.
Restart the document camera using the power the control panel.
button on
77
Appendix A:
79
Appendix A
Hardware environmental compliance
SMART Technologies supports global efforts to ensure that electronic equipment is manufactured, sold and disposed of in a safe and environmentally friendly manner.
Waste Electrical and Electronic Equipment regulations (WEEE directive)
Waste Electrical and Electronic Equipment regulations apply to all electrical and electronic equipment sold within the European Union.
When you dispose of any electrical or electronic equipment, including SMART Technologies products, we strongly encourage you to properly recycle the electronic product when it has reached the end of its life. If you require further information, please contact your reseller or
SMART Technologies for information on which recycling agency to contact.
Restriction of Certain Hazardous Substances
(RoHS directive)
This product meets the requirements of the European Union’s Restriction of Certain Hazardous
Substances (RoHS) directive 2002/95/EC.
Consequently, this product also complies with other regulations that have arisen in various geographical areas, and that reference the European Union’s RoHS directive.
Packaging
Many countries have regulations restricting the use of certain heavy metals in product packaging. The packaging used by SMART Technologies to ship products complies with applicable packaging laws.
81
Index
3
3D models
manipulating with Mixed Reality Tools 69
A
C
Capturing images
D
document camera
document cameras
using with SMART Notebook software 47
E
F
G
H
I
L
I N D E X
M
Mixed Reality Tools for SMART Document
modes
N
Notebook software See SMART Notebook
O
P
Playback mode
printed documents, displaying 27
R
82
S
SketchUp sketching software 73
T
U
V
W
Z
SMART Technologies smarttech.com/support smarttech.com/contactsupport
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
Key features
High-resolution 5 MP CMOS sensor
8x optical zoom, 8x digital zoom
Up to 30 frames per second
Automatic or manual focus
Maximum shooting area 15 3/4" × 11 3/4"
Integrated microphone and flexible arm
Microscope mode with adapters
VGA, DVI-I, and composite video outputs
Supports SD/SDHC cards (up to 32 GB) and USB drives
Integrates with SMART Notebook software and Mixed Reality Tools
Frequently asked questions
The SMART Document Camera 450 has three main modes: Camera mode for live viewing and capture, Computer Pass-Through mode for displaying computer input, and Playback mode for viewing stored images and videos.
To connect to a computer, set the USB switch on the left-side connection panel to the computer icon, then connect a USB cable from the document camera's rear USB receptacle to your computer. Ensure SMART Notebook software 11 SP1 or later is installed.
Yes, the document camera supports SD/SDHC cards (up to 32 GB, speed class 10 recommended) and USB drives for storing captured images, audio, and video recordings.
In Camera mode, press the Menu button, navigate to the Image tab, select 'MODE', and then choose 'Sharp' for text documents or 'Graphics' for documents with images.
The mixed reality cube allows you to interact with and manipulate 3D models within SMART Notebook software using the Mixed Reality Tools.