SMART Technologies Document Camera 450 User guide
Tangazo
Tangazo
SMART Document
Camera™ 450
User’s guide
Product registration
If you register your SMART product, we’ll notify you of new features and software upgrades.
Register online at smarttech.com/registration .
Keep the following information available in case you need to contact SMART Support.
Serial number:
Date of purchase:
FCC warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the US Federal Communications Commission
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Trade-mark notice
SMART Document Camera, SMART Board, SMART Notebook, SMART Exchange, smarttech, the SMART logo and all SMART taglines are trade-marks or registered trade-marks of SMART Technologies ULC in the US and/or other countries. Google 3D Warehouse and SketchUp are trade-marks of Google Inc. Adobe,
Reader and Acrobat are registered trade-marks or trade-marks of Adobe Systems Incorporated in the United States and/or other countries. Windows is either a registered trade-mark or trade-mark of Microsoft Corporation in the US and/or other countries. Mac and OS X are trade-marks of Apple Inc., registered in the US and other countries. All other third-party product and company names may be trade-marks of their respective owners.
Copyright notice
© 2012 SMART Technologies ULC. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language in any form by any means without the prior written consent of SMART Technologies ULC. Information in this manual is subject to change without notice and does not represent a commitment on the part of SMART.
This product and/or use thereof covered by one or more of the following US patents.
www.smarttech.com/patents
01/2013
i
Important information
W A R N I N G l
Failure to follow the installation instructions included with your SMART product could result in personal injury and damage to the product.
l
Ensure that any cables extending across the floor to your SMART product are properly bundled and marked to avoid a trip hazard.
l
To reduce the risk of fire or electric shock, do not expose the SMART product to rain or moisture.
l
Do not push foreign objects into the openings on your SMART product.
l
Do not open or disassemble the SMART product. You risk electrical shock from the high voltage inside the casing. Opening the casing also voids your warranty.
l
The camera arm on your SMART product has joints that present a pinch hazard when you move the camera arm. Keep clear of the pinch points.
l
Do not stare into the light or shine the light directly into someone’s eyes. Turn off the light when displaying or capturing images of people.
l
Do not overload power sockets or extension cords as this can result in a fire or electric shock.
l
Turn off and disconnect your SMART product before a thunderstorm. During a thunderstorm, do not touch your SMART product or the power plug, because there is a risk of electrical shock.
l
Only use your SMART product with the type of power source that is written on the power supply and do not modify the plug.
C A U T I O N l
Place your SMART product on a solid surface to prevent it from falling.
l
If you have a security cable attached to our SMART product, do not carry or swing your
SMART product by the security cable.
ii
I M P O R T A N T I N F O R M A T I O N l
Do not connect non-shielded interface cables to your SMART product and do not leave cables connected to unused connectors, because this can cause interference levels that exceed FCC regulations.
l
Avoid setting up and using the SMART product in an area with excessive levels of dust, humidity and smoke.
l
Do not block or cover the openings or slots on your SMART product. These slots provide ventilation, ensure reliable operation and protect your SMART product from overheating.
l
Do not carry your SMART product by the camera arm. Carry it by the base of the unit.
l
Do not aim the camera lens at the sun.
l
If your SMART product requires replacement parts, make sure that the service technician uses replacement parts specified by SMART Technologies or parts with the same characteristics as the original.
iii
Contents
Chapter 2: Setting up your SMART Document Camera
Setting up your document camera
Connecting your document camera to different displays
Turning your document camera on and off
Connecting your document camera to external devices
Shooting area, overhead light and anti-glare sheet
Chapter 3: Using your SMART Document Camera
Understanding Camera, Computer Pass-Through and Playback modes
Identifying features of each mode
Inserting and removing an SD/SDHC card
Chapter 4: Using your SMART Document Camera in Camera mode
Using the on-screen display (OSD) menu in Camera mode
Capturing and transferring images and videos
Chapter 5: Using your SMART Document Camera with SMART Notebook software
Using your document camera with SMART Notebook software
Chapter 6: Using your SMART Document Camera in Playback mode
Setting your document camera to Playback mode
Using the Playback mode on-screen display (OSD) menu
Deleting images in Playback mode
C O N T E N T S
Chapter 7: Using 3D Tools for SMART Notebook software and Mixed Reality Tools
Incorporating 3D content into your lessons
Getting started with Mixed Reality Tools for SMART Document Camera
Inserting and manipulating 3D models
Using Mixed Reality Tools for SMART Document Camera
Using SketchUp sketching software and Trimble 3D Warehouse
Appendix A: Hardware environmental compliance
Waste Electrical and Electronic Equipment regulations (WEEE directive)
Restriction of Certain Hazardous Substances (RoHS directive)
iv
Chapter 1:
1
Chapter 1
Overview
Adjustable camera arm and camera head
SMART Notebook software and SMART Product Drivers
Introduction
Your document camera 450 can transform any classroom or lecture hall into a spontaneous and interactive learning environment. It uses a high-resolution video camera to display clear and detailed images of written material or any physical object.
Your SMART Document Camera™ 450 enables you to display printed documents, microscope slides and 3D objects on your computer, projector or television. You can record videos, scan documents, capture images and save them to a SMART Notebook™ collaborative learning software file or to an SD/SDHC card or USB drive.
2
C H A P T E R 1
Overview
Your document camera integrates with SMART Notebook software and SMART Board® interactive whiteboards, creating an interactive presentation environment.
You can use the mixed reality cube with your document camera to manipulate 3D models in
SMART Notebook files.
Document camera features
Camera
l
High resolution 5 MP CMOS sensor l
8× optical zoom, 8× digital zoom l
Internal memory l
Up to 30 frames per second l
Automatic or manual focus l
Maximum shooting area 40cm x 30cm (15 3/4" × 11 3/4") l
Microphone integrated into base l
Microscope mode that requires adapters
Output/input
l
VGA and DVI-I outputs XGA (1024 × 768), SXGA (1280 × 1024), 720p (1280 × 720), 1080p
(1920 × 1080) l
Composite video output with user-selectable NTSC or PAL formats l
RGB (VGA) input (when selected by the user) is a pass-through to the VGA output.
Physical construction
l
Security lock slot l
Flexible arm l
Bright LED overhead light
Software
l
SMART Notebook software 11 or later, including 3D Tools for SMART Notebook software and Mixed Reality Tools software.
l
SMART Product Drivers
C H A P T E R 1
Overview
Image and video storage
l
Supports SD/SDHC cards with a built-in card slot (up to 32 GB, speed glass 4).
l
Supports USB drivers.
l
Supports USB mass storage mode for internal memory and SD card when connected to a computer.
Parts of the document camera
Adjustable camera arm and camera head
You can fold and adjust the flexible arm to position the lens at any angle. The camera head has a bright LED overhead light to enhance the lighting condition.
1 Camera head
2 Camera lens
3 Overhead light
4 Flexible arm
5 Control panel
Control panel
You can use the control panel to switch between Camera, Computer Pass-Through and
Playback modes. You can also use it to control features and settings in the Camera mode's onscreen display menu.
Button
3
C H A P T E R 1
Overview
1 Select/Enter
2 Menu
3 Record video
7 Select playback
8 Overhead light on/off
9 Image brightness
4 Power on/off
5 Select camera
10
11
Zoom in/out
Auto-focus
6
Select computer passthrough
12 Capture to SMART Notebook software or to local memory
13 USB indicator: computer or USB drive
For information on the different modes, see Understanding Camera, Computer Pass-Through and
4
5
C H A P T E R 1
Overview
Rear connection panel
The rear connection panel has DC 12V 2A, VGA In, VGA Out, Composite Video Out and USB mini-B connectors.
1 Connect the power cable
2 Connect a VGA output connector of a computer
3 Connect any display device with a VGA cable
4 Connect the supplied composite video adapter cable
5 Connect a USB connector of a computer
Left-side connection panel
The left-side connection panel has a DVI output, a switch for selecting either a computer or a
USB drive, and audio in and out connect.
1 Connect any display device with a DVI cable
2 USB switch
3 Connect a USB drive
4 Connect an external microphone
5 Connect speakers for video playback only
C H A P T E R 1
Overview
Right-side connection panel
The right-side connection panel has an SD/SDHC card slot, a switch for selecting VGA-DVI or composite video output and a security lock slot.
1 Camera head storage
2 SD/SDHC card slot
3 TV/VGA switch
4 Security lock slot
Bottom control panel
The NTSC/PAL switch is on the bottom control panel. This switch enables you to change the format of the composite video output for your television. Changes to the selected video output take effect the next time you turn on your document camera. The resolution reset button resets the output VGA/DVI resolution to XGA.
N O T E
You can press the resolution reset button with a pen tip. Pressing the button for three seconds resets the output VGA/DVI resolution to 1024 × 768.
6
1 NTSC/PAL switch
7
C H A P T E R 1
Overview
2 Resolution reset button
Mixed reality cube
With a mixed reality cube, you can interact with 3D models in SMART Notebook software using
Mixed Reality Tools. See Using 3D Tools for SMART Notebook software and Mixed Reality
Power supply
Your document camera comes with a power supply, including a country-specific connector that connects to the external power supply. Plug adapters for North America, Great Britain, Europe and Australia are provided.
USB cable
Use the USB cable to connect your document camera to your computer. You can display objects, capture images to SMART Notebook files and control your document camera from
SMART Notebook software.
VGA cable
Use the VGA cable to connect your document camera to a computer, projector or display. You can display objects and capture images and videos to a storage device.
Composite video adapter cable
Use the composite video adapter cable to connect your document camera to a projector or a display. You can display objects, capture images and videos to a storage device and use the features in the on-screen menus.
N O T E
The provided DB9 connector isn’t needed in any of the connection configurations.
Microscope adapter
Your document camera comes with a microscope adapter and two different sized rubber couplers to fit the microscope eyepiece. With a microscope you can examine microscopic objects on a big screen.
Anti-glare sheet
Place the anti-glare sheet over printed documents to reduce glare.
8
C H A P T E R 1
Overview
Document camera modes
Your document camera has three modes you can use to control how it sends data to a computer, projector, monitor or television.
l
Camera mode controls your document camera from its control panel and displays images on a projector, monitor or television.
l
Computer Pass-Through mode displays the image from the VGA input on a projector, monitor or television connected to the VGA output.
l
Playback mode controls your document camera from its control panel and displays images from an SD/SDHC card or USB drive on a connected projector, monitor or television.
See Understanding Camera, Computer Pass-Through and Playback modes on page 21 for more
information on these modes.
9
C H A P T E R 1
Overview
Document camera software
Your document camera includes software downloads that you need to present images from your document camera.
SMART Notebook software and SMART Product Drivers
Your document camera uses SMART Notebook software and SMART Product Drivers.
SMART Notebook software is presentation software designed to work with
SMART Document Cameras and the touch features of SMART Board interactive whiteboards. In addition, with a mixed reality cube, you can manipulate 3D models in SMART Notebook files
using Mixed Reality Collaboration tools (see Using 3D Tools for SMART Notebook software and
Mixed Reality Tools on page 53).
You can find system requirements for your computer in the SMART Notebook software 11.1
release notes ( smarttech.com/kb/170138 ).
I M P O R T A N T
You need to have SMART Notebook software 11 SP1 or later installed on your computer before you connect your document camera.
Downloading software
To install SMART Notebook software and SMART Product Drivers
1. Go to smarttech.com/software.
2. Scroll to SMART Notebook collaborative learning software.
3. Click Choose a version, select the latest version of SMART Notebook software for
Windows® or Mac and then follow the on-screen instructions.
Chapter 2:
11
Chapter 2
Setting up your
SMART Document Camera
Setting up your document camera
Connecting your document camera to different displays
Connecting your document camera to a monitor or a projector
Connecting your document camera to a monitor or a projector with a DVI interface
Connecting your document camera to a TV or a projector
Turning your document camera on and off
Connecting your document camera to external devices
Connecting your document camera to a microscope
Switching between VGA, DVI and composite output
Connecting your document camera to an external microphone
Connecting your document camera to speakers
Shooting area, overhead light and anti-glare sheet
Introduction
This chapter explains how to set up your document camera and how to connect with different displays and devices. It also explains external memory storage usage.
C H A P T E R 2
Setting up your SMART Document Camera
Setting up your document camera
The document camera has a flexible arm with rotational movement for easy positioning display objects.
To unfold and position your document camera
1. Place a hand on the base of the document camera to stabilise it.
2. Press the camera head down and then pull the camera arm outward and upward.
3. Move the camera head to aim the lens at your object.
I M P O R T A N T
To use your document camera with SMART Notebook software you need to connect your document camera to a computer.
To connect the power supply
1. Connect the power supply cable to the DC 12V port on the rear connection panel.
2. Connect a country-specific connector to the power supply.
12
C H A P T E R 2
Setting up your SMART Document Camera
3.
C A U T I O N
Ensure that you connect the power connector to the power supply before connecting the power plug to a power socket.
4. Connect the plug to a power socket.
To use your document camera in Camera or Playback mode, connect your document camera directly to an external display.
To connect your document camera to a computer with a USB cable
1. Set the USB switch on the left side connection panel to .
The indicator on the control panel lights up, and you can use your document camera as a USB camera or to transfer captured pictures/videos from the memory source to your computer.
2. Connect a USB cable to the USB port on the rear connection panel.
3. Locate the USB connector on your computer and then connect the cable to it.
To connect your document camera to a computer with a VGA cable
1. Connect a VGA cable to the VGA In port on the rear connection panel.
2. Locate the VGA Out connector on your computer and then connect the cable to it.
Connecting your document camera to different displays
Once you have completed the basic connection procedure, you can connect your document camera to an external display. This enables you to use the document camera in Camera mode
and Playback mode (see page 21) and to access the on-screen display menu for those modes.
You can connect your document camera directly to an external display to enable the following functions: l
Use Camera mode to view the camera image in full-screen on the external display.
l
Use Playback mode to view a full-screen slide show on the external display.
I M P O R T A N T
To use your document camera with SMART Notebook software you need to connect your document camera to a computer.
13
C H A P T E R 2
Setting up your SMART Document Camera
Setting the TV/VGA switch
The TV/VGA switch determines the display output selection. Set it to VGA (right) using a VGA or DVI connection for a signal output. Set it to TV (left) connection for a composite output.
when when using an RCA
Connecting your document camera to a monitor or a projector
In this configuration your document camera is connected to your external display device with a
VGA cable.
To connect your document camera to a monitor or a projector
1. Complete the basic connection steps (see page 12).
I M P O R T A N T
Make sure that the TV/VGA switch is set to VGA .
2. Connect a VGA cable to your document camera's VGA Out port and your display device'sVGA In connector.
Connecting your document camera to a monitor or a projector with a
DVI interface
In this configuration your document camera is connected to your external display device with a
DVI cable (not supplied).
To connect your document camera to a monitor or a projector with a DVI interface
1. Complete the basic connection steps (see page 12).
I M P O R T A N T
Make sure that the TV/VGA switch is set to VGA .
2. Connect a DVI cable to your document camera's DVI Out port and your monitor's or projector’sDVI Input connector.
3. Connect your document camera to an external display with a VGA cable (see page 15).
This configuration makes it easy to transition from Computer Pass-Through mode to
Camera mode or Playback mode using the same projector or display for all three modes.
Connecting your document camera to a TV or a projector
In this configuration your document camera is connected to your computer with both a composite video adapter cable and an RCA cable.
14
C H A P T E R 2
Setting up your SMART Document Camera
To connect your document camera to a TV or a projector
1. Complete the basic connection steps (see page 12).
2. Connect a composite video adapter cable to your document camera's Composite Video port.
3. Connect an RCA cable to your display's Video In connector.
4. Connect the composite video adapter and the RCA cables (see page 15).
I M P O R T A N T
Do not connect the 9-pin cable
DVI or composite video displays will not display your computer view. A VGA display is required.
Turning your document camera on and off
To turn on your document camera
Press the power button on the control panel.
The power light changes from amber to flashing green. When the light is solid green, your document camera is operational.
To turn off your document camera
Press the power button on the control panel.
The power light changes from green to amber.
Connecting your document camera to external devices
You can connect your document camera directly to the following external devices: l
Microscope l
Microphone l
Speakers
15
C H A P T E R 2
Setting up your SMART Document Camera
Connecting your document camera to a microscope
You can connect your document camera to a microscope. This enables you to examine microscopic objects on a big screen.
To set up a microscope
1. Select the appropriate rubber coupler size for the microscope eyepiece and insert it in the microscope adapter.
2. Attach the microscope adapter to your document camera's camera head and then connect it to your document camera.
3. Tighten the three bolts until the adapter secures the eyepiece.
16
C H A P T E R 2
Setting up your SMART Document Camera
4. Fit the camera head with the microscope adapter over the microscope's eyepiece.
I M P O R T A N T
Make sure that the arrow on the camera head and microscope adapter are on the same side.
5. Turn the microscope adapter anticlockwise to line up the arrows and lock the microscope adapter in place.
To connect the microscope to a projector or a display
1. Press the button on the control panel and then select the tab.
2. Use the button on the control panel to selectMODE and then press the the control panel.
3. Use the control panel.
button on the control panel to select and then press the button on button on the
4. Press the button on the control panel to close the menu.
5. Connect the other end of the VGA cable to the VGA In connector on your projector or display.
6. Set the VGA/TV switch on the right-side connection panel to VGA .
Switching between VGA, DVI and composite output
If you’re using a projector or a computer display with a VGA or a DVI cable, set your document camera to the VGA mode. If you’re using a television with the composite video cable, set your document camera to the TV mode
17
C H A P T E R 2
Setting up your SMART Document Camera
To set your document camera to the VGA mode
Set the VGA/TV switch on the right-side connection panel to VGA .
To set your document camera to the TV mode
Set the VGA/TV switch on the right-side connection panel to TV .
Connecting your document camera to an external microphone
You can connect an external microphone to your document camera.
N O T E S l
The built-in microphone on the control panel is disabled when an external microphone is connected.
l
The audio is in monophonic sound.
To connect an external microphone to your document camera
Connect the microphone's cable to the microphone on your document camera's left-side connection panel.
Connecting your document camera to speakers
You can connect speakers to your document camera. Only audio from the video playback is supported.
C A U T I O N
Turn the volume down to prevent hearing damage when using earphones.
To connect speakers
Connect the speakers’ 3.5 mm cable to the speaker port on your document camera's leftside connection panel.
Shooting area, overhead light and anti-glare sheet
Shooting area
The shooting area can view a maximum area of 40cm x 30cm (15 3/4" × 11 3/4").
18
C H A P T E R 2
Setting up your SMART Document Camera
To rotate the image
1. Press the
2. Press the button on the control panel.
button on the control panel and then select button on the control panel.
.
3. Press the
4. Press the
5. Press the button on the control panel and then selectROTATE.
button on the control panel.
6. Select rotation range and then press the button on the control panel.
7. Press the button on the control panel to close the menu.
To mirror the image
1. Press the button on the control panel.
button on the control panel and then select 2. Press the
3. Press the
.
button on the control panel.
button on the control panel and then selectMIRROR.
4. Press the
5. Press the button on the control panel.
6. Select ON orOFF and then press the button on the control panel.
7. Press the button on the control panel to close the menu.
Overhead light
Press the off.
button on your document camera's control panel to turn the overhead light on or
Anti-glare sheet
The anti-glare sheet is a special coated film that helps to eliminate any glare that could be encountered whilst displaying glossy objects, such as magazines and photos. Place the antiglare sheet on top of the object to reduce reflected light.
19
C H A P T E R 2
Setting up your SMART Document Camera
External memory storage
Your document camera supports both an SD/SDHC card and a USB drive for image capture, audio and video recordings. Your document camera detects when an external storage device is connected and automatically switches to the last detected storage. If no external storage device is connected, all captured images are saved in the built-in memory.
I M P O R T A N T
Your document camera comes with piece of plastic inserted in the SD card slot. Remove this piece of plastic before you insert your SD/SDHC card.
N O T E S l
Your document camera supports SD/SDHC cards with up to 32 GB, speed class 10.
l
SDHC card with class-6 or higher is recommended for high-quality recording.
l
Push in the SD/SDHC card to eject it.
To connect a USB drive
1. Set the USB switch on the left-side connection panel to
Your document camera detects the USB drive and the lights up.
2. Insert the USB drive into the USB port.
N O T E S
Your document camera supports USB drives with up to 64 GB.
.
indicator on the control panel
20
Chapter 3:
21
Chapter 3
Using your
SMART Document Camera
Understanding Camera, Computer Pass-Through and Playback modes
Identifying features of each mode
Inserting and removing an SD/SDHC card
Introduction
This chapter provides information about your document camera's different modes.
Understanding Camera, Computer Pass-
Through and Playback modes
You can use your document camera in Camera, Computer Pass-Through or Playback mode.
Each mode enables you to complete different functions and requires a specific connection to either a display, a projector or a computer.
Camera mode
In Camera mode, you can view document camera images only in SMART Notebook software.
Camera mode allows connection over USB and live image output. You can view full-screen images from your document camera using a projector or high-definition display without a computer.
C H A P T E R 3
Using your SMART Document Camera
You can save images to your SMART Notebook file to present them later, or if your computer is connected to an interactive whiteboard, projector or television, you can deliver your
SMART Notebook presentation with live images from your document camera.
N O T E
The Capture button on the control panel saves the image to the Notebook page and closes the
SMART Document Camera window. Pressing the Capture button again will re-open the
SMART Document Camera window.
You can use the Camera mode’s on-screen display menu for greater control of the image.
See Using your SMART Document Camera in Camera mode on page 27.
Computer Pass-Through mode
Computer Pass-Through mode switches your document camera's video output to the VGA input.
You can switch between the live camera image and your computer screen image.
You can view the document camera live image only in SMART Notebook software.
N O T E S l
Capture button on the control panel has no effect in Computer Pass-Through mode.
l
In Computer Pass-Through mode, you can only view the document camera live image in
SMART Notebook software.
Playback mode
In Playback mode you can view full-screen images and slide shows from the memory card on a projector or high-definition display without a computer. You can’t use your document camera as a mass storage device in Playback mode.
Identifying features of each mode
The following table describes the differences between each mode.
Feature description Camera mode
Computer
Pass-Through mode
Playback mode
View computer input (VGA In) No Yes (VGA out and DVI analogue)
No
22
C H A P T E R 3
Using your SMART Document Camera
Feature description
View document camera image
View pictures from a memory card
Access an internal memory and SD/SDHC card from the computer with a USB cable
Control the document camera from a computer
Capture to SMART Notebook software
Capture to an SD/SDHC memory card
Access the related on-screen display menu
Capture to a USB drive
Yes
No
Yes
[1]
Yes
Yes
Yes
Yes
Yes
[2]
No
No
Yes
[1]
Yes
[1]
No
No
No
No
N O T E S l
[1] Only when the USB switch is set to l
[2] Only when the USB switch is set to
. See The Setting tab on page 35.
. See The Setting tab on page 35.
The following table describes outputs when your document camera is connected to a display with
VGA, DVI or Composite Video Out.
Feature description Camera mode
Computer
Pass-Through mode
Playback mode
No
Yes
No
No
No
No
Yes
No
Connect to a projector or display (VGA out and DVI analogue output)
Camera image
Connect to a DVI digital output projector or a display
Connect to a television (composite video out)
Camera image
Camera image
Camera mode
Computer
Pass-Through mode
Playback mode
VGA In
N/A
N/A
Memory card images
Memory card images
Memory card images
23
C H A P T E R 3
Using your SMART Document Camera
Setting document camera modes
To set your document camera to Camera mode
1. Set your document camera to Computer mode using the switch on the left-side connection panel. The USB indicator on the control panel displays .
2. Connect your document camera to your computer with the USB cable.
3. Set the TV/VGA switch on the right-side connection panel to VGA .
4. Connect your document camera to a projector, monitor or television with a VGA cable.
5. Press the button on the control panel.
To set your document camera to Computer Pass-Through mode
1. Connect your document camera to your computer with the USB cable.
2. Connect your computer with the VGA cable to your document camera's VGA In port.
3. Connect your display device with another VGA cable to your document camera's VGA Out port.
4. Press the button on the control panel.
To set your document camera to Playback mode
1. Disconnect the USB cable from the rear connection panel.
2. Connect your document camera to a projector or a monitor with the VGA cable or to a television with the composite video adapter cable if needed.
3. Press the button on the control panel.
Displaying printed documents
When you set your document camera to Camera mode, you can display printed documents, use the anti-glare sheet to reduce glare, and optimise the image for text and graphic documents with the Image mode options.
To display printed documents
1. Place your documents on the table.
2. Adjust the document camera and then aim its lens at your documents.
3. Press the button on the control panel to adjust the focus.
24
C H A P T E R 3
Using your SMART Document Camera
To reduce glare
If glare makes it difficult for you to read the printed documents that you’re displaying, place the anti-glare sheet on top of the printed documents.
To optimise the image for text documents
1. Set your document camera to Camera mode.
2. Press the button on the control panel.
The on-screen display menu appears.
3. Press the control panel.
button on the control panel to select and then press the button on the
4. Press the button on the control panel to selectIMAGE MODE and then press the button on the control panel.
5. Press the control panel.
button on the control panel to select and then press the
See The Image tab on page 29 for an explanation of the settings.
button on the
To optimise the image for documents with graphics
1. Set your document camera to Camera mode.
2. Press the button on the control panel.
The on-screen display menu appears.
3. Press the control panel.
button on the control panel to select and then press the button on the
4. Press the button on the control panel to selectIMAGE MODE and the press the button on the control panel.
5. Press the control panel.
button on the control panel to select and then press the
See The Image tab on page 29 for an explanation of the settings.
button on the
Inserting and removing an SD/SDHC card
Your document camera has an SD/SDHC card slot on the right-side connection panel. You can save document camera images to an SD/SDHC card when your document camera is in Camera or Computer Pass-Through mode. When your document camera is in Playback mode you can display previously captured images from an SD/SDHC card.
25
C H A P T E R 3
Using your SMART Document Camera
C A U T I O N
Avoid static electricity near a card because it can damage.
I M P O R T A N T
Your document camera comes with a piece of plastic inserted in the SD/SDHC card slot.
Remove this piece of plastic before you insert your SD/SDHC card.
To insert an SD/SDHC card
1. Press the button on the control panel.
2. Insert an SD/SDHC card into the card slot on the right-side connection panel with the contact facing down.
I M P O R T A N T l
You might need to set your document camera to use the SD/SDHC card as the storage
location (see The Setting tab on page 35).
l
Ensure that the label on the SD/SDHC card is facing up.
To remove an SD/SDHC card
C A U T I O N
To prevent memory card damage, do not remove the memory card whilst capturing or deleting images.
1. Press the live image.
button on the control panel and wait until your document camera displays a
2. Push in the card to eject it and then remove the card.
26
Chapter 4:
27
Chapter 4
Using your
SMART Document Camera in
Camera mode
Using the on-screen display (OSD) menu in Camera mode
Using the Picture in Picture (PiP) feature
Capturing and transferring images and videos
Transferring images to your computer
Introduction
This chapter explains how to use your document camera in Camera mode.
Using Camera mode
When your SMART Document Camera is connected to a projector, flat-panel display or television you can display a full-screen image from your document camera.
You can use your document camera in Camera mode to perform the following tasks: l
Display objects.
l
Capture images to an SD/SDHC card.
l
Capture images to SMART Notebook.
l
Use the features and settings in the on-screen display menu.
l
Use a microscope with a standard eyepiece with additional adapters.
C H A P T E R 4
Using your SMART Document Camera in Camera mode
I M P O R T A N T
Your document camera must be connected directly to an external display when using the OSD
menu. See Connecting your document camera to external devices on page 15.
To switch to Camera mode
1. Connect your document camera to a projector or flat-panel display with the appropriate cable
(see Connecting your document camera to external devices on page 15).
2. Press the button on the control panel.
To display objects
1. Press the button on the control panel.
2. Place the object you want to display under the camera.
3. Rotate the camera head to aim the lens at your object.
To adjust the zoom magnification
Press the button on the control panel.
To automatically adjust the focus
Press the button on the control panel.
To adjust brightness settings
Press the button on the control panel.
To record a video
1. Insert an SD/SDHC card or USB drive into the appropriate port.
2. Press the
3. Press the button on the control panel to start recording.
button on the control panel to stop recording.
Using the on-screen display (OSD) menu in
Camera mode
There are four tabs on the OSD menu: Image, Presentation, Setting and System. Use the OSD menu to adjust settings for your document camera in Camera mode.
28
C H A P T E R 4
Using your SMART Document Camera in Camera mode
To navigate the OSD menu and submenus
1. Set your document camera to Camera mode.
2. Press the button on the control panel.
The OSD menu appears.
3. Press the
4. Press the
5. Press the
6. Press the
7. Press the and and buttons on the control panel to toggle between tabs.
buttons on the control panel to choose a selection in the menu list.
button on the control panel to make a selection.
button on the control panel to enter a submenu.
button on the control panel to return to the previous menu level.
8. Press the button on the control panel to exit the menu.
The following OSD menu options are available when your document camera is in Camera mode.
Tab
Image
Presentation
Settings
System
Options
Brightness, Contrast, Mode, Effect, Mirror, Advanced, Focus, Rotate.
Picture in Picture (PiP), Split Screen, Timer. See The Presentation tab on page 32.
Capture, Recording, Storage, Format, USB to PC and Flicker.
Language, Output Display, Backup, Save Setting, Recall Setting,
Information, Default.
The Image tab
To access the Image settings menu
1. Press the button on the control panel.
2. Press the button on the control panel.
3. Press the control panel.
button on the control panel to select and then press the button on the
29
C H A P T E R 4
Using your SMART Document Camera in Camera mode
4. Press the or on the control panel.
button on the control panel to select and then press the button
30
Image options
Brightness
Contrast
Mode
Effect
Mirror
Advanced o Auto Image
Description
Adjust the image brightness manually.
Adjust the image contrast.
Select an option from five image settings: o
Sharp – adjust the contrast to make text appear more visible o
Graphics – adjust the image gradient o
Motion – increase the frame rate (sufficient lighting is required when using this setting) o
Macro – set when viewing an object that is close to the camera, no more than 20cm (7 3/4") away from the camera o
Infinite – set when viewing an object that is more than 55cm (22") away from the camera
Convert the image to colour, black/white or film negative image.
Select to flip the image: o o
OFF – displays a normal image
ON – displays a mirrored image
Select to automatically adjust white balance and exposure and to correct colour and exposure compensation.
C H A P T E R 4
Using your SMART Document Camera in Camera mode
Image options o Exposure o White Balance
Focus
Rotate
Description
Select the exposure setting: o o
AUTO – automatically adjust the camera exposure
MANUAL – manually adjust the camera exposure
Select the white balance setting for various light conditions: o
AUTO – automatically adjust the white balance o MANUAL – manually adjust the red and blue colour levels up to 255.
Adjust the focus manually.
o o o o
OFF – displays normal image rotation
90° – rotates the image 90°
180° – rotates the image 180°
270° – rotates the image 270°
31
C H A P T E R 4
Using your SMART Document Camera in Camera mode
The Presentation tab
Presentation features enable you to show previously captured images along with the live camera view. These features aren't available when the document camera is connected as a USB camera.
To access the Presentation tab
1. Press the button on the control panel.
2. Press the button on the control panel.
3. Press the control panel.
button on the control panel to select
4. Press the control panel.
button on the control panel to select and then press the button on the and then press the button on the
32
C H A P T E R 4
Using your SMART Document Camera in Camera mode
Presentation options Description
Picture in Picture (PiP) o Shows captured pictures or video as thumbnails in corner of the screen in Camera mode.
33
Split Screen o Press the left and right navigation buttons to navigate through the stored images.
o Press the button to cancel PiP.
o o o
Divides the screen in two parts.
Half of the screen displays thumbnail images and the other half displays the image from your document camera.
Select the display location: left, right, top, bottom.
o Press the left/right and up/down navigation buttons to highlight the image.
o Press the button to select the image.
o Press the left/right and up/down navigation buttons to pan the stored image.
o
Press the button to cancel split screen.
C H A P T E R 4
Using your SMART Document Camera in Camera mode
Presentation options
Timer
Description o
N O T E
You can’t capture an image whilst in Split Screen mode.
o Provides an on-screen countdown timer for a presenter to assist with presentation time management.
Using the Picture in Picture (PiP) feature
The PiP feature allows you to display an image from stored memory within the live camera image. This is useful for showing before and after comparisons.
N O T E
The PiP feature is for display purposes only. You can’t capture an image whilst in PiP mode.
To display the PiP image
1. Display an object in Camera mode and then press the
The OSD menu appears.
2. Press the control panel.
button on the control panel to select button on the control panel.
and then press the button on the
3. Press the control panel.
button on the control panel to select PiP and then press the button on the
34
C H A P T E R 4
Using your SMART Document Camera in Camera mode
4. Select the corner of the display and then press the button on the control panel.
Your document camera displays a picture in picture image.
5. Press and buttons on the control panel to choose different stored images.
The Setting tab
To access the Setting tab
1. Press the button on the control panel.
2. Press the button on the control panel.
3. Press the control panel.
button on the control panel to select
4. Press the control panel.
button on the control panel to select and then press the button on the and then press the button on the
35
C H A P T E R 4
Using your SMART Document Camera in Camera mode
Settings options
Capture o Resolution o Quality o Type o Interval
Recording
Storage
Format
USB to PC
Flicker
Description
Select image capture size. In 5M setting, the capture resolution is 2592 × 1944.
Select image quality; Finest, High, Normal.
Select image capture type: o o
Single – capture one picture at a time
Continuous – capture consecutive pictures
Set the time interval for continuous capture. The length can be set up to 600 sec (10 min).
Select the video recording compression setting.
Change the storage location: o Audio and video recording can be saved only on an
SD/SDHC card, or a USB drive.
Delete all the data in the selected memory.
Select the status of your document camera when it’s connected to the computer using a USB cable. Make sure the USB switch on the left-side connection panel is set to o
.
Camera – can be used as a computer webcam, to o capture still images or to record a video
Storage – transfer captured images or videos from the memory to a computer hard drive
Select refresh rate: o o
50 Hz – sets frequency to 50 Hz
60 Hz – sets frequency to 60 Hz
Playback mode
Playback mode sets how your document camera, computer and a memory card interact.
To access the Playback mode
1. Press the button on the control panel.
2. Press the button on the control panel.
3. Press the control panel.
button on the control panel to select
4. Press the and then press the button on the button on the control panel to select USB to PC and then press the
36
C H A P T E R 4
Using your SMART Document Camera in Camera mode button on the control panel.
5. Select STORAGE and then press the button on the control panel.
Action
See the memory card from your computer
View and use your document camera from SMART Notebook software
Capture image to the memory card in both Computer Pass-
Through and Camera modes
Storage
Yes
No
No
Camera
No
Yes
Yes
This mode enables you to see the contents of your USB drive or SD memory card from your computer.
The mass storage mode enables you to see the contents of the embedded memory or SD/SDHC card from your computer. They will show up as removable disks. Look in the document camera
DCIM directories for the stored images and videos.”
The System tab
To access the System menu
1. Connect your document camera to a projector, flat-panel display or television (see page 16).
2. Press the button on the control panel.
3. Press the button on the control panel.
The OSD menu appears.
4. Press the control panel.
button on the control panel to select and then press the button on the
37
C H A P T E R 4
Using your SMART Document Camera in Camera mode
System options
Language
Output Display
Backup
Save Settings
Recall Settings
Information
Default
Description
Select or change the language: o o o o
English
Français
Deutsch
Español
Set the resolution to display an image on the screen: o o o o
1024 × 768
1280 × 1024
1280 × 720
1920 × 1080
N O T E
This selection disabled in TV output mode.
o o
SD/SDHC – copy images and presentations from the build-in memory to an SD/SDHC card
USB drive – copy images and presentations from the build-in memory to a USB drive
Save the current setting in the selected profile number.
N O T E
Only effect, mode, brightness and contrast settings can be saved.
Restore the setting to the selected profile number.
Display the product information.
Restore all the settings to the factory default settings.
Capturing and transferring images and videos
You can capture images and videos from your document camera to an SD/SDHC card or USB drive and transfer them to a computer.
Capturing images
You can capture images and videos to an SD/SDHC card or USB drive when your document camera is in Camera mode.
To capture images to memory
1. Set your document camera to Camera mode. See Using Camera mode on page 27.
2. Position your document camera.
38
C H A P T E R 4
Using your SMART Document Camera in Camera mode
3. Adjust any camera settings using the Camera mode’s OSD menu. See Using Camera mode on page 27.
4. Press the button on the control panel.
To record a video using an SD/SDHC card
1. Insert an SD/SDHC card in your document camera's SD/SDHC card slot.
2. Press the control panel.
button on the control panel to select
3. Press the to selectSTORAGE and then press the
The document camera detects the SD/SDHC card.
and then press the button on the button on the control panel.
4. Press the
2.
N O T E button on the control panel to start recording.
The video saves in .AVI format in your SD/SDHC card.
5. Press the button on the control panel to stop recording.
To record a video using a USB drive
1. Insert a USB drive in your document camera’s USB port.
2. Press the to selectSTORAGE and then press the
The document camera detects the USB drive.
button on the control panel.
3. Press the
2.
N O T E button on the control panel to start recording.
The video saves in .AVI format in your USB drive.
3. Press the button on the control panel to stop recording.
Transferring images to your computer
You can transfer images from your external storage device to your computer.
39
C H A P T E R 4
Using your SMART Document Camera in Camera mode
To transfer images to your computer
1. Use the OSD menu to set your document camera USB to PC mode to STORAGE.
2. Connect your document camera to your computer with the USB cable (see Setting up your
Your computer recognizes your document camera and the external storage device as a removable disk.
3. Browse to the removable disk on your computer and then transfer the images to your computer.
Using a microscope
You can view the microscope stage through the document camera using additional attachments.
See Connecting your document camera to external devices on page 15.
To display a microscope slide
1. Place a slide or object on the stage of the microscope.
2. Focus the microscope so that the subject is in sharp focus.
3. Position the microscope under your document camera so the camera lens is aligned with the microscope eyepiece.
C A U T I O N
Ensure that you do not hit your document camera lens with the microscope. This could damage your document camera’s lens.
4. Press the button on the control panel.
5. Press the button on the control panel.
6. Press the control panel.
button on the control panel to select and then press the
7. Press the button on the control panel to selectMODE and then press the the control panel.
button on the button on
8. Press the control panel.
button on the control panel to select and then press the button on the
40
Chapter 5:
41
Chapter 5
Using your
SMART Document Camera with SMART Notebook software
Using your document camera with SMART Notebook software 41
Using your document camera with
SMART Notebook software
You can display objects and capture an image to a SMART Notebook page.
You can present images from your document camera through SMART Notebook software. The interactive whiteboard or projector displays your computer desktop or SMART Notebook file.
I M P O R T A N T
Your document camera should be in Camera mode. SMART Notebook software also works
with the camera in the Computer Pass-Through mode. See The Setting tab on page 35.
N O T E
For information on using 3D Tools for SMART Notebook software and Mixed Reality Tools for
SMART Document Camera, see Using 3D Tools for SMART Notebook software and Mixed
To open a SMART Document Camera window
1. Connect your SMART Document Camera to your computer and turn on the document camera.
2. Start SMART Notebook software.
3. Press SMART Document Camera on the SMART Notebook menu bar.
A SMART Document Camera window appears.
C H A P T E R 5
Using your SMART Document Camera with SMART Notebook software
4. Place the object or objects that you want to display under the camera.
5. Press any of the following on the menu bar to adjust the image.
Menu option Description
Zoom out.
Zoom in.
Decrease brightness.
Increase brightness.
Focus automatically.
Focus out manually.
Focus in manually.
Change the appearance of the image: rotate it 180º, define the image colour, black and white or film negative. You can also start and stop
Microscope mode and start Mixed Reality Tools for
SMART Document Camera automatically.
Start Mixed Reality.
Insert a screen capture on the current page and then close the window.
Capture an image and insert a screen capture on a new page and keep the current window open.
To take a series of screen captures
1. Open a SMART Document Camera window.
2. Press Capture with Time-Lapse on the SMART Document Camera window menu bar and then select a period of time. (For example, if you want to take a screen capture every 15 seconds, select 15 Seconds.)
42
C H A P T E R 5
Using your SMART Document Camera with SMART Notebook software
3. When you’ve finished, press to stop recording.
N O T E
The display appears in the bottom left-hand corner of your SMART Notebook page. It displays the time that has lapsed since the last screen capture and the number of screen captures taken.
To use a microscope
1. Connect your document camera to a microscope. See Connecting your document camera to
2. Open a SMART Document Camera window.
3. Press Additional Settings on the SMART Document Camera window menu bar and then select Start Microscope Mode.
N O T E
The Additional Settings button doesn’t appear if you’re using a
SMART Document Camera 230 with SMART Notebook software.
4. Press Additional Settings and then select Stop Microscope Mode when you’ve finished.
43
Chapter 6:
45
Chapter 6
Using your
SMART Document Camera in
Playback mode
Setting your document camera to Playback mode
Using the Playback mode on-screen display (OSD) menu
Playback mode OSD menu options
Deleting images in Playback mode
Introduction
This chapter explains how you can use your document camera in Playback mode. When you set your document camera to Playback mode, you can play back images from the SD/SDHC card,
USB drive or internal memory. You can browse through the stored images and display previously captured images either individually or as a slide show.
N O T E
In this mode your document camera can’t be connected by a USB cable and you must have images stored in either internal or external memory source.
Setting your document camera to Playback mode
Playback mode takes over the video output of the document camera. Live images and USB functions are not available during this time.
To set Playback mode using an SD/SDHC card
1. Connect your document camera directly to a projector or another display. For connection
C H A P T E R 6
Using your SMART Document Camera in Playback mode
2. Insert an SD/SDHC card in your document camera.
3. Press the button on the control panel.
To set Playback mode using a USB drive
1. Connect your document camera directly to a projector or another display. For connection
2. Set the USB switch to . The USB indicator on the control panel is lit.
3. Press the button on the control panel.
Using the Playback mode on-screen display
(OSD) menu
The Playback mode OSD menu shows the source storage location and controls how stored images are displayed.
Playback mode OSD menu options
To access the Playback mode OSD menu
1. Connect your document camera directly to a projector or another display. For connection
2. Set the USB switch to
OR
. The USB indicator on the control panel is lit.
Disconnect the computer USB connection to change the memory location to the USB drive.
3. Press the button on the control panel.
Playback mode OSD menu
46
C H A P T E R 6
Using your SMART Document Camera in Playback mode
Playback menu option
Slide Show
Interval
Effect
Current Storage
Delete All
Description
Displays all captured still images in an automated slide show.
Sets the slide show interval (in 5 second increments) before displaying the next image. The maximum interval is 100 sec.
Selects the slide show transition effect: o o o o o
Slide image
Checker down
Wipe down
Split vertical out
Split horizontal in
Chooses the storage source if more than one is available. Detects the storage source if only one is available.
Permanently deletes all the data in the selected memory source.
N O T E
A warning message appears. Select YES to continue or NO to stop.
To select the settings for a slide show
1. Press the button on the control panel to access the Playback mode OSD menu.
2. Press the and buttons on the control panel to make a selection and then press the button on the control panel.
and buttons on the control panel to toggle between functions.
3. Press the
4. Press the button on the control panel to make a selection.
5. Press the button on the control panel to close the menu.
Repeat steps 2–4 as needed.
To play a slide show
1. Connect your document camera directly to a projector or another display. For connection
2. Set the USB switch to
OR
. The USB indicator on the control panel is lit.
Insert an SD/SDHC card or a USB drive in the appropriate port.
47
C H A P T E R 6
Using your SMART Document Camera in Playback mode
3. Press the button on the control panel.
Thumbnail images from the memory source are displayed.
4. Press the
5. Press the button on the control panel.
button on the control panel twice to start the slide show.
6. Press the button on the control panel to stop the slide show or to return to the thumbnails view.
To play a video
N O T E
In the thumbnails view, videos have a image.
symbol in the top left-hand corner of the thumbnail
1. Connect your document camera directly to a projector another display. For connection
2. Set the USB switch to . The USB indicator on the control panel is lit.
3. Insert an SD/SDHC card or a USB drive in the appropriate port.
48
C H A P T E R 6
Using your SMART Document Camera in Playback mode
4. Press the button on the control panel.
Thumbnail images from the memory source are displayed.
5. Press the and buttons on the control panel to toggle between images.
6. Press the button on the control panel to select the video that you want to play.
49
C H A P T E R 6
Using your SMART Document Camera in Playback mode
7.
N O T E
Press the
Press the
Press the button to pause your video.
or button to adjust the volume.
button to rewind and the button to fast-forward.
8. Press the view.
button on the control panel to stop the video or to return back to thumbnails
Deleting images in Playback mode
You can delete all images at once from your document camera’s three memory sources using the
OSD menu, or you can delete only selected images.
To delete all images
I M P O R T A N T
You are unable to delete images from your computer in Playback mode. You can delete images only from the three memory sources.
1. Select the memory source that you want to delete all the images from.
2. Press the button on the control panel to access the Playback mode OSD menu.
3. Press the button on the control panel to select DELETE ALL.
4. Press the selection.
button on the control panel and then press the
The DELETE ALL warning appears.
button again to make a
5. Press the or button on the control panel to select YES or NO.
50
C H A P T E R 6
Using your SMART Document Camera in Playback mode
6. Press the
7. Press the button on the control panel to DELETE or CANCEL.
button on the control panel again to close the Playback mode OSD menu.
N O T E
The deleting-image icon appears briefly whilst your document camera deletes images.
To delete selected image
1. Press the button on the control panel to display all the images in the memory storage.
2. Press the want to delete.
or or or button on the control panel to select the image that you
3. Press the button on the control panel.
The DELETE THIS IMAGE warning appears.
4. Press the
5. Press the or button on the control panel to select YES or NO.
button on the control panel to DELETE or CANCEL.
51
Chapter 7:
53
Chapter 7
Using 3D Tools for
SMART Notebook software and Mixed Reality Tools
Incorporating 3D content into your lessons
Getting started with Mixed Reality Tools for SMART Document Camera
Activating 3D Tools for SMART Notebook software and Mixed Reality Tools
Hardware and software requirements
Inserting and manipulating 3D models
Pausing, playing and restarting animation
Using Mixed Reality Tools for SMART Document Camera
Manipulating 3D models using Mixed Reality Tools for SMART Document Camera
Disguising 3D models before presenting them
Using SketchUp sketching software and Trimble 3D Warehouse
Using SketchUp sketching software
Introduction
This chapter provides the information that you need to begin using SMART Document Camera as well as SketchUp™ sketching software and Trimble® 3D Warehouse™ (formerly Google™ 3D
Warehouse).
SMART Notebook software.
3D Tools for SMART Notebook software and Mixed Reality Tools take this experience to a new level by providing teachers and students with a new way to engage with digital 3D content.
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
Incorporating 3D content into your lessons
You can incorporate 3D content into your SMART Notebook software lessons. The following are examples of how to do this: l
If you’re teaching a biology lesson, insert a 3D model of a heart into your .notebook file.
Rotate and change the size of the 3D model to present the different parts of the heart.
l
If you’re teaching an English lesson, insert a 3D model of a city that is referenced in a novel the class is reading. Enter the 3D scene to navigate streets and interiors of buildings.
l
If you’re teaching a primary lesson, insert multiple 3D models and use the Disguise feature to reveal answers as a memory exercise.
Getting started with Mixed Reality Tools for
SMART Document Camera
Activating 3D Tools for SMART Notebook software and
Mixed Reality Tools
3D Tools for SMART Notebook software and Mixed Reality Tools provide an intuitive way for students and teachers to explore digital content with the SMART Document Camera.
When you connect your document camera to your computer, 3D Tools for SMART Notebook software and Mixed Reality Tools activate automatically. If you want to use 3D Tools for
SMART Notebook software on a computer that has never been connected to a document camera, you can activate 3D Tools for SMART Notebook software by obtaining a product key and following the procedure below.
N O T E
You can obtain a product key for 3D Tools for SMART Notebook software by registering your document camera’s serial number at smarttech.com/register .
To activate 3D Tools for SMART Notebook software
1. For Windows operating systems, select Start > All Programs > SMART Technologies >
SMART Tools > SMART Product Update.
For Mac OS X operating system software, browse to and double-click
Applications\SMART Technologies\SMART Tools\SMART Product Update.
The SMART Product Update window appears.
2. Click Activate in theSMART Notebook row.
The SMART Software Activation dialogue box appears.
54
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
3. Click Add.
4. Type the product key you received from SMART in the Product Key box and then clickAdd.
5. Click licence agreement, review the licence agreement and then clickClose.
6. If you accept the licence agreement, select the I accept the terms in the licence
agreement tickbox.
7. Click Next.
3D Tools for SMART Notebook software activates.
8. Click Finish and then close theSMART Product Update window.
Hardware and software requirements
To get started with Mixed Reality Tools for SMART Document Camera, you need the following: l
SMART Notebook software 11 SP1 l
SMART Document Camera 450 l
A mixed reality cube l
A computer meeting the requirements in the SMART Notebook software release notes
( smarttech.com/kb/170144 ).
Lighting requirements
Mixed Reality Tools works best in a bright room where the work surface doesn’t have any noticeable shadows or glare.
The light must be as uniform as possible, shining on the cube and background. You can achieve this by setting up the document camera so that the camera is facing directly down, perpendicular to a uniform, neutral work surface. The work surface should not be darker than the black elements on the mixed reality cube or lighter than the white elements on the cube.
N O T E S l
In very bright rooms, the work surface can appear whiter than the white elements on the cube.
l
To help increase the contrast between the cube elements and the background, and to increase the image frame rate, you can place a piece of white paper under the cube.
A typical projector room is usually quite dark. For Mixed Reality Tools to work properly, the document camera’s light should be turned on. Don’t manipulate the cube more than 35cm (14") from the document camera.
55
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
N O T E
If SMART Notebook software doesn’t enter Mixed Reality mode when you hold the cube under the camera, shake the cube under the camera. If the issue persists, press and hold the brighten button on the document camera to maximise the brightness.
Inserting and manipulating 3D models
To use 3D Tools for SMART Notebook software, you need to insert a 3D model in your .notebook
file. After you insert a 3D model, you can manipulate it in the same way that you manipulate other objects in SMART Notebook software.
N O T E
You can insert 2D images and 3D models on the same page and manipulate them the same way that you manipulate other objects in SMART Notebook software.
Inserting 3D models
3D models are available from the 3D Objects folder in Lesson Activity Examples and the
SMART Exchange™ website ( exchange.smarttech.com
) as well as the Trimble 3D Warehouse
(seeUsing Trimble 3D Warehouse on page 65). You can also insert your own 3D models if they
are in one of the following formats: l
COLLADA (.dae) l
3D Object (.obj) l
FBX (.fbx)
N O T E
Textures and other information for some 3D models are stored in separate files and folders.
When you insert these 3D models, ensure the 3D model file is located in the correct folder structure with the supporting files and folders.
To insert a 3D model
1. Select Insert > 3D File.
The Insert 3D File dialogue box appears.
2. Browse to and select the 3D model you want to insert.
3. Press Open.
The 3D model appears on the page.
56
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
Manipulating 3D models
Once you have inserted a 3D model, you can manipulate it in the same way that you manipulate other objects in SMART Notebook software. In particular, you can do the following: l
Cut, copy and paste l
Clone l
Move l
Scale l
Lock l
Attach links and sounds l
Add to the Gallery tab
N O T E S l
For information on these basic options, see the Help for SMART Notebook software.
l
When you add a 3D model to the Gallery tab, it appears in the 3D Objects category.
In addition to these basic options, you can do the following: l
Rotate the 3D model l
Pause, resume, play and restart animation l
Add labels
Rotating a 3D model
You can rotate a 3D model along multiple axes. After rotating a 3D model, you can reset it to its original orientation.
To rotate a 3D model along a single axis
1. Select the 3D model.
2. Press and hold one of the side rotation handles.
3. Drag your finger around the centre of the 3D model and then release your finger when finished.
To rotate a 3D model along multiple axes
1. Select the 3D model.
2. Press and hold the centre rotation handle.
57
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
3. Drag your finger in the direction that you want to rotate the 3D model and then release your finger when finished.
To reset a 3D model to its original orientation
1. Select the 3D model.
2. Press the 3D model’s menu arrow and then select Reset Rotation.
Pausing, playing and restarting animation
If a 3D model contains animation, you can pause, resume and restart the animation.
N O T E
If a 3D model doesn’t contain animation, the Animation menu documented in the following procedures is disabled.
To pause animation
1. Select the 3D model.
2. Press the 3D model’s menu arrow and then select Animation > Play/Pause Animation.
To resume playing animation
1. Select the 3D model.
2. Press the 3D model’s menu arrow and then select Animation > Play/Pause Animation.
To restart animation
1. Select the 3D model.
2. Press the 3D model’s menu arrow and then select Animation > Restart Animation.
Adding labels
You can use labels to highlight different components of a 3D model. Labels can be text, shapes or other 2D objects.
To add a label
1. Select the 3D model.
2. Right-click the 3D model where you want to connect the label and then select Add Label.
A label appears.
58
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
3. To use text in the label, double-click the label’s default text and then type your own text.
OR
To use a shape or other 2D object in the label, create the object and then drag it into the label.
4. Optionally, drag the label’s connection point to a different location on the 3D model.
To hide and display a label
1. Press the label’s connection point on the 3D model.
The label is hidden.
2. Press the label’s connection point to display the label.
To remove a label
1. Select the label.
2. Press Close .
Navigating 3D scenes
Large 3D models that contain internal details are called 3D scenes. You can navigate 3D scenes using controls in SMART Notebook software.
N O T E S l
You can use the navigation controls to navigate any 3D model. However, not all 3D models contain internal details. If you enter a 3D model that doesn’t contain internal details, the interior appears empty or dark.
l
If you’re using Mac OS X operating system software, you’re unable to enter a 3D scene while in Full Screen mode. To enter a 3D scene, first exit Full Screen mode and then complete the following procedure.
59
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
To navigate a 3D scene
1. Select a 3D model.
2. Press the 3D model’s menu arrow and then select Enter 3D Scene.
SMART Notebook software displays the 3D scene in Full Screen mode. A map of the 3D scene, navigation controls and the Close button appear.
T I P S o You can press the grey border of the map to drag it to another area of the page if it’s covering materials that you want to present. You can also resize the map by pressing and dragging the grey border in the lower right-hand corner.
o You can press the grey background or centre icon of a navigation control to drag it to another area of the page if it’s covering materials that you want to present.
60
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
3. Navigate the 3D scene using the navigation controls.
61
Button
G
H
E
F
I
J
C
D
A
B
Use to:
Change your orientation upward.
Change your orientation to the left.
Change your orientation to the right.
Change your orientation downward.
Raise elevation.
Move forward in the scene.
Move to the left in the scene.
Move to the right in the scene.
Move backward in the scene.
Lower elevation.
Alternatively, you can use keyboard buttons to navigate the 3D scene.
Keyboard button
D
S
W
A
PAGE UP
UP ARROW
LEFT ARROW
Use to:
Change your orientation upward.
Change your orientation to the left.
Change your orientation to the right.
Change your orientation downward.
Raise elevation.
Move forward in the scene.
Move to the left in the scene.
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
Keyboard button
RIGHT ARROW
DOWN ARROW
PAGE DOWN
ESC
Use to:
Move to the right in the scene.
Move backward in the scene.
Lower elevation.
Close
N O T E
As you navigate the 3D scene, a red indicator in the map displays where you are in the scene and the direction you are viewing. The arrow in the centre indicates orientation. The arrow becomes a circle when you’re facing directly up or down.
Level Incline Decline
Off-screen (level) Upward
4. Press Close when you’ve finished.
Downward
Using Mixed Reality Tools for
SMART Document Camera
After inserting 3D models in your .notebook files using 3D Tools for SMART Notebook software, you can manipulate those models using Mixed Reality Tools for SMART Document Camera.
Manipulating 3D models using Mixed Reality Tools for
SMART Document Camera
You manipulate 3D models using your SMART Document Camera and the mixed reality cube.
To manipulate a 3D model using the mixed reality cube
1. Connect your SMART Document Camera to your computer and turn on the document camera.
2. Open the .notebook file and then display the page containing the 3D model.
62
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
3. Place the mixed reality cube under the SMART Document Camera, showing one side of the cube to the camera.
SMART Notebook software enters Mixed Reality mode and assigns the 3D model to the cube. If there is more than one 3D model on the page, move the cube until the animation on the page indicates that the cube is connected to the 3D model you want to manipulate.
N O T E
SMART Notebook software enters Mixed Reality mode in this situation only if a 3D model is on the page. Alternatively, you can enter Mixed Reality mode by pressing SMART
Document Camera in the toolbar and then pressing Start Mixed Reality in the
SMART Document Camera window.
4. Do any of the following: o To move the 3D model on the screen, move the cube.
o To rotate the 3D model on the screen, rotate the cube in your hand.
o To unassign the 3D model from the cube, cover the cube’s markings with your hand.
N O T E
If you experience any of the following symptoms, the cause may be issues with tracking: o The 3D model doesn’t connect to the cube.
o The 3D model shakes when it’s connected to the cube.
o The 3D model sporadically disconnects from the cube.
o SMART Notebook software enters Mixed Reality mode when the cube is under the camera even if you aren’t moving the cube.
To address tracking issues, see Lighting requirements on page 55.
T I P S o As you move and rotate the cube in your hand, ensure that you don’t cover the symbols on the cube’s surface.
o To hide the image from the SMART Document Camera and show only the 3D model, move the transparency slider to the left.
63
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
5. If you’ve purchased a second cube from SMART and there is more than one 3D model on the page, manipulate another 3D model by completing steps 3 and 4 with the other cube.
N O T E
The two cubes must have different patterns if you want to use them both at the same time.
6. When you’re done, move the cube (or cubes) away from the camera.
SMART Notebook software exits Mixed Reality mode after a few seconds.
Disguising 3D models before presenting them
If you want to hide 3D models in your .notebook file before presenting them, you can use the
Disguise feature to hide the 3D models with a magic hat.
When you use Mixed Reality Tools, the magic hat disappears after Mixed Reality Tools assigns the 3D model to the cube, revealing the 3D model.
N O T E
If you hide multiple 3D models on the same page with magic hats, each magic hat has a different coloured ribbon.
To hide a 3D model with a magic hat
1. Select the 3D model.
2. Press the 3D model’s menu arrow and then select Disguise > Disguised.
To change the magic hat’s colour
1. Select the magic hat.
2. Press the magic hat’s menu arrow and then select Disguise > Change Colour.
To reveal a 3D model under a magic hat
Use Mixed Reality Tools as described in Manipulating 3D models using Mixed Reality
Tools for SMART Document Camera on page 62.
After Mixed Reality Tools assigns the 3D model to the cube, stars swirl around the magic hat, and then the magic hat disappears, revealing the 3D model behind it.
64
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
T I P
You can also reveal the 3D model by pressing the hat corner.
icon in the lower left-hand
Using SketchUp sketching software and
Trimble 3D Warehouse
You can use the following 3D tools with 3D Tools for SMART Notebook software and Mixed
Reality Tools: l
SketchUp sketching software l
Trimble 3D Warehouse (formely Google 3D Warehouse)
Using SketchUp sketching software
You can use SketchUp sketching software to create 3D models. You can save these 3D models in COLLADA (.dae) format and then insert them in SMART Notebook software.
To save a 3D model in .dae format
1. Open the 3D model in SketchUp sketching software.
2. Select File > Export > 3D Model.
The Export Model dialogue box appears.
3. Browse to where you want to save the file.
4. Type a name for the file in the File name box.
5. Select COLLADA File (*.dae) in the Export type drop-down list.
6. Press Export.
To insert the 3D model in SMART Notebook software
See Inserting 3D models on page 56.
Using Trimble 3D Warehouse
Trimble 3D Warehouse (formerly Google 3D Warehouse) is an online repository of 3D models.
Using this link in the SMART Notebook software Gallery tab, you can search for 3D models and download them to your computer. You can then insert the 3D models into your .notebook files.
To download 3D models
1. Press the Gallery tab.
2. Press Google 3D warehouse.
65
C H A P T E R 7
Using 3D Tools for SMART Notebook software and Mixed Reality Tools
3. Search or browse for a 3D model that you want to download.
Select the model.
4. Press Download Model and then press the Download link beside Collada (.zip).
N O T E S o When you first download a 3D model, you may be asked to provide a nickname.
o If you’re using Mac OS X operating system software and you cancel the download, the 3D model still saves to the Downloads folder.
5. Save the .zip file to your computer.
6. Extract the contents of the .zip file to a folder on your computer.
To insert a downloaded 3D model
See Inserting 3D models on page 56.
66
Chapter 8:
67
Chapter 8
Troubleshooting
This chapter includes troubleshooting information for your SMART Document Camera.
Document camera issues
Use the following table to troubleshoot issues with your document camera.
N O T E
These procedures vary depending on your version of Windows operating system and your system preferences.
Issue
The power light turns orange in standby mode.
No camera image displays
(Camera mode).
No computer image displays
(Computer Pass-Through mode)
Solution
Press the power light turns green.
button again to turn it on. The power l l l l
Ensure that your document camera is turned on.
Check all cable connections.
Check the TV/VGA switch on the right-side connection panel of your document camera and set it to the type of display device that you have.
Reset the output resolution to 1024×768 by using a pen tip or other small object to press the resolution reset button on the bottom of the document camera.
l l l l l
Ensure that your document camera is turned on.
Check all cable connections.
Check the cable connections from the computer VGA output to the VGA input of your document camera.
Ensure that your document camera is in Computer Pass-
Through mode.
On some laptop computers, you can press FN+F5 repeatedly to toggle between display modes and the computer image on the presentation screen.
C H A P T E R 8
Troubleshooting
Issue
The presentation screen is dark and unreadable.
Solution l l l l l
Turn on Auto Image in your document camera’s on-screen display (OSD) menu (Menu > IMAGE > Advanced > Auto
Image) to adjust the image brightness..
Reset your document camera to its default settings (Menu >
SYSTEM > Default > Yes > Enter).
Make sure that there’s enough light in the room, or turn on the overhead light on your document camera.
Adjust the brightness and contrast levels manually in the document camera's OSD menu, or use the control panel buttons.
If you are using a projector, check the bulb.
The image on the presentation screen is distorted or blurry.
SMART Notebook software doesn’t detect your document camera.
l l
Reset your document camera to its default settings (Menu >
SYSTEM > Default > Yes).
Adjust the brightness and contrast manually to reduce the distortion.
l
Press the button on the control panel if the image is blurry or out of focus.
l l l
Make sure that your USB cable is connected.
Make sure that the USB switch is set to .
Make sure that your software is up-to-date (you should have at least SMART Notebook software 11 SP1).
l l
Make sure that the USB cable and the computer USB port are working properly.
Make sure that the USB to PC setting is set to CAMERA in the document camera's OSD menu.
SMART Notebook software enters Mixed
Reality mode unexpectedly.
l l
Press SMART Document Camera in the toolbar.
Press Additional Settings and then clear the selection of Automatically Start Mixed Reality Tools.
1.
N O T E
To enable the automatic detection of Mixed Reality again, press Additional Settings and then select
Automatically Start Mixed Reality Tools.
No image appears when you press the button.
l
Insert an SD/SDHC card or USB drive with stored images, or capture an image to the embedded memory.
1.
N O T E
Images need to be stored in the available memory location in order to enter Playback mode.
l
Disconnect the USB cable or set the USB switch to .
68
C H A P T E R 8
Troubleshooting
Issue
Your document camera doesn't detect the inserted
USB drive.
You're unable to record a video (the red recording light doesn’t turn on).
The SD/SDHC card or
USB drive doesn't play video properly, or the document camera stops responding during video recording.
Solution
Ensure that the USB switch is set to l l
.
Ensure that an SD/SDHC card or USB drive is installed.
Disconnect the USB cable (the document camera doesn't record video whilst being used as a USB camera or mass storage device).
Format the SD/SDHC card or USB drive using the document camera's OSD menu (Menu > SETTING > Format > SD
CARD / USB DRIVE).
1.
C A U T I O N
This erases all the data on the SD/SDHC or USB drive.
Your document camera has an issue not described above.
Restart the document camera using the power the control panel.
button on
69
Appendix A:
71
Appendix A
Hardware environmental compliance
SMART Technologies supports global efforts to ensure that electronic equipment is manufactured, sold and disposed of in a safe and environmentally friendly manner.
Waste Electrical and Electronic Equipment regulations (WEEE directive)
Waste Electrical and Electronic Equipment regulations apply to all electrical and electronic equipment sold within the European Union.
When you dispose of any electrical or electronic equipment, including SMART Technologies products, we strongly encourage you to properly recycle the electronic product when it has reached the end of its life. If you require further information, please contact your reseller or
SMART Technologies for information on which recycling agency to contact.
Restriction of Certain Hazardous Substances
(RoHS directive)
This product meets the requirements of the European Union’s Restriction of Certain Hazardous
Substances (RoHS) directive 2002/95/EC.
Consequently, this product also complies with other regulations that have arisen in various geographical areas and that reference the European Union’s RoHS directive.
Packaging
Many countries have regulations restricting the use of certain heavy metals in product packaging.
The packaging used by SMART Technologies to send products complies with applicable packaging laws.
73
Index
3
3D models
manipulating with Mixed Reality Tools 62
A
C
Capturing images
D
document camera
document cameras
using with SMART Notebook software 41
E
F
G
H
I
L
M
I N D E X
Mixed Reality Tools for SMART Document
modes
N
Notebook software See SMART Notebook
O
P
Playback mode
printed documents, displaying 24
R
S
SketchUp sketching software 65
74
T
U
V
W
Z
SMART Technologies smarttech.com/support smarttech.com/contactsupport
Pakua
Kiungo cha umma kime sasishwa
Kiungo cha umma kwa mazungumzo yako kimesasishwa. You may view and manage your chat links after registration here.
Kiungo cha umma cha hati
Tangazo