Compaq Mega-Post User manual

PDF

Document

Diagnostic Card

PC Analyzer

Version 4.0 PCI

User’s Guide

User’s Guide

Model: postcard_40

For use only in a desktop model computer with PCI slot

User’s Guide

INTRODUCTION

Diagnostic Card is a powerful diagnostic tool for technicians and administrators to troubleshoot various problems of IBM compatible PCs. It is easy to install, yet extremely powerful to use. With

Diagnostic Card in hand, you no longer have to go through tedious and time consuming process of trying to figure out what is wrong with your PC hardware. Diag nostic Card will tell you exactly what is wrong with your PC in just seconds. It saves you time and money.

Our new and improved design of diagnostic card can work with almost all popular types of CPUs,

Motherboards, and BIOS.

All though we tr y, it is not possible to update this manual ever y time a new motherboard is made by the manufactures. It is always advised to visit the bios manufacture website, and download the latest codes per bios revision. Or visit bioscentral.com for an online reference.

System Requirements

The Diagnostic Card itself only requires an empty PCI expansion slot. It is not necessary to install memory chips to perform analysis. “POST Codes” can be displayed through the hexadecimal display panel on the Diagnostic Card itself.

Tech Support

Tech Support 1-888-359-0747 [email protected]

Diagnostic Card INDICATORS

Two ‘Indicators’ are any light emitting diode s (LED) or hexadecimal displa y panel that may be mounted on an Diagnostic Card. This section discusses the follo wing indicators that appear on the

Diagnostic Card: l

POST Code Display l

PCI BUS SIGNALS LEDs

POST Code Display

The POST Code Display is made up of a dual, dot matrix hexadecimal read -out that displays Power

On Self Test (POST) status codes.

Power On Self -Test (POST) Codes

Most AT and 386 computers (and a few XT computers) output status codes during POST. The

Diagnostic Card displays these codes during and after PO ST. Refer to Appen dix A for a comprehensive listing of POST codes provided by BIOS manufacturers.

User’s Guide

PCI Signal Definition:

TRDY

IRDY

FRAME

RESET

3V3

Device Ready. Flashes when an TRDY signal is detected.

I/O Read y. Flashes when an IRDY signal is detected.

PCI Bus Frame. Should be on under normal circumstances and flashes when a PCI Frame Signal is detected .

Reset. After power on or reset, this in dicator should be on for an half second and then turned o ff.

Power Supply, 5 -Volt Positive. Should be on all the time otherwise there is a short circuit.

Power Supply, 3.3 -Volt. Some motherboards have 3.3V power supply to

PCI slots. This indicator should be on if the motherboard supplies 3.3V power.

INSTALLING Diagnostic Card

Installation Procedure

TO INSTALL A Diagnostic Card:

1) Install the Diagnostic Card in any available PCI expansion slot.

2) Power on the machine.

User’s Guide

POST Codes

When the machine is turned on, the hexadecimal displa y should show the various POST codes as the system executes (unless it has a rare BIOS that does not display POST codes).

If the machine does not boot, s ystem POST has detected a fatal fault and stopped. The number showing in the hexadecimal display on the Diagnostic Card is the number of the test in which

POST failed. Refer to Appendix A for a listi ng of POST codes.

Troubleshooting During POST

After initial power up, Power-On Self-Test (POST) codes begin displaying on the Diagnostic

Card’s hexadecimal displays (for most machines).

NOTE: A few machines use the parallel port to display POST codes instead of the Diagnostic

Card.

THE POST PROCESS

The ROM built onto the motherboard of the computer rums its built -in POST (Power-On Self-Test) when you switch power on to the computer, press the reset button on the computer, or press

Ctrl-Alt-Del (warm boot). POST performs a tightly interwoven initialization and testing process for each of these methods, but it typically does not test or initialize memory above 64K for warm boot.

You can get an even better idea of the detailed pr ocess by studying the POST code listings in

Appendix A.

Appendix A

AMI

Error Code-00

(00)Going to give control to INT 19H boot loader.

AMI

Award

Error Code-01

(01)Processor register test about to start, and NMI to be disabled,286 reg. test about to start.

(01)Processor test 1;Processor status(1FLAGS) verification; Tests the followin g processor status flags carry, zero, sign, overflow. The BIOS will set each of these flags, verify the y are set then turn each flag off and verify it is off.

(01)[Beep]=none 80286 register test in –progress. Phoenix

AMI

Error Code - 02

(02)NMI is disabled. Power on delay starting. Power on delay starting.286reg.

AST

Award

(02)Test CPU register.

(02)Processor test 2;Read/write/ verify all CPU registers except SS,SP and BP with data pattern FF&00.Determine status o f manufacturing jumper.

Chips&Tech (02)Test CPU register.

Dell

Phoenix

(02)[Beep]=1-1-3 CMOS write/read test .

(02)Verify real-mode operation(Beep)=1 -1-1-3.CPU Flags test.

Phoenix (02)[Beep]=1-1-3 CMOS write/read test in-progress or failure.

AMI

AST

Error Code – 03

(03)Power on delay complete. To check soft reset/power-on. Any initialization before keyboard BAT is in progress. ROM BIOS c hecksum(32K at F800:0) passed.

(03)Test 8042 keyboard controller reset.

Award

(03)Initialize Chips; Disable N MI,PIE,AIE,UEI,SQWV, disable video, parit y checking, DMA; Reset math Coprocessor; Clear all page registers, CMOS shutdown byte; Initialize timer 0,1 and 2 including set EISA timer to a known state; Initialize

DMA controllers 0 and 1; Initialize interrupt controller 0 and 1;Initialize EISA extended registers. Calculate BIOS EPROM and sign -on message checksum; fail if not 0.Initialize EISA registers(EISA)BIOS only).Clear 8042 keyboard controller.

Chips & Tech (03)ROM did not checksum.

Phoenix&Dell

(03)Disable Non-Maskable Interrupt(NMI).[Beep]=1 -1-4 BIOS ROM checksum in-progress or failure.

Error Code – 04

AMI

AST

AMI

AST

(04)Any initializati on before keyboard BAT is complete. Reading ke yboard SYS bit, to check soft reset/power-on. Reading keyboard SYS bit, to check soft reset/power

On. Keyboard controller test with and without mouse passed. 8259 initialization OK.

(04)Low level keyboard communication, keyboard ID verification.

Award

(04)Test memory refresh toggle; RAM must be periodically refreshed in order to keep the memory from decaying. This function assur es that the memory refresh function is worki ng properly. Test CMOS RAM I/O port interface and veri fy battery power is available(bat. status=1).Reset 8042.

Chips & Tech (04)DMA Controller failed.

Phoenix&Dell

(04)Get the CPU type (Beep)=1 -1-2-1.CPU register test. Programmable Interval

Timer test failure.

Error Code – 05

(05)Soft reset/power -on determined. Going to enable ROM. i.e. disable shadow

RAM/Cache if any. Going to enable ROM.i.e. disable shadow RAM/cache if any.Chipset initializati on over,DMA and interrupt controller disabled. CMOS pending interrupt disabled.

(05)Read keyboard input port.

Chips & Tech (05)System timer bad.

Award

(05)Keyboard controller self-test enable keyboard inter face. Blank video, Initialize keyboard; Keyboard controller initialization. Initialize Chips; Disable

NMI,PIE,AIE,UEI, SQ - WV, disable video, parity checking, DMA; Reset math Coprocessor; Clear all page registers,CMOS shutdown byte; Initialize timer 0,1 and 2 including set EISA timer to a known state; Init ialize DMA controllers 0 and

1;Initialize interrupt controller 0 an d 1; Initialize EISA extended Regis- ters.Get manufacturing status, reset if set(loop 1 -5).

Phoenix&Dell (05)[Beep]=1-2-2 DMA initialization in-progress or failure.

Error Code – 06

AMI (06)ROM is enabled. Calculating ROM BIOS checksum, and waiting for Keyboard

Appendix A

AST controller input buffer to be free. Calculating ROM BIOS checksum.Video disabled and system timer test begin. Video disabled and system timer counting O K.

(06)Support chipset initialize.

Award

(06)Test memory refresh toggle;RAM must be periodicall y refreshed in-order to keep the memory from decaying.This function assures that the memory refresh function is working properl y.Initialize c hips.

Chips & Tech (06)64K RAM Failed.

Phoenix&Dell (06)Initialize system hardware (Beep)=1 -1-2-3.DMA page register write/read tes t

AMI in-progress or fail.

Error Code – 07

(07)ROM BIOS checksum passed.CMOS shutdown regi - ster test to be done

Award next.ROM BIOS checksum passed, Keyboard controll er I/B free.Going to issue the

BAT command to keyboar d controller.Goin g to issue the BAT command to keyboard controller.CH -2 of 8254 initializat ion half way.CH-2 of 8253 test OK

(07)Verifies CMOS’s basis R/W functionality.Test CMOS interface and battery status;Verifies CMOS is workin g correctly,detects bad batter y. Setup low memory;

Early chip set initialization; Memory presence test; OEM chip set routines; Clear low 64K of memory; Test first 64K memory; clear lower 256K of memory, enable parity checking and test parity in lower 256K; test lower 25 If the BIOS detects error

2C,2E,or 30(b ase 512K RAM error),it displays 6K memory. Set up stack,beep.Read/write/verify CPU registers.

Chips & Tech (07)64K RAM failed data test (Base Memory)

Error Code – 08

ACER (08)Shutdown 0.

AMI

Award

(08)CMOS shutdown register test done. CMOS checksum calculation to be done next. BAT command to ke yboard controller is issued. Goin g to verify the BAT command. Goi ng to verify the BAT command. CH-2 of timer initialization over.

CH-2 delta count test OK

(08)Setup low memory; Early chip set initialization; Memory presence test; OEM chip set routines; Clear low 64K of memor y; Test first 64K memory; clear lower

256K of memory, enable parit y checking and test parity in lower 256K; test lower

256K memory. Set up stack, beep. Setup interrupt vector table in lower 1K RAM area; Initialize first 120 interrupt vectors with SPURIOUS_INT_HDLR and initialize INT 00h-1Fh according to INT_TB L. Initialize CMOS timer.

Chips & Tech (08)Interrupt Controller bad.

Phoenix&Dell (08)Initialize chipset registers with POST values. [Beep]= 1 -3-1 RAM refresh

AMI verification in-progress or failure.

Error Code – 09

(09)CMOS checksum calculation is done, CMOS diag byte written. CMOS initiali ze

AST to begin. Keyboard controller BAT result verified. Ke yboard command byte to be written next.(09)Keyboard command byte to be written next. CH -1 of timer initializatio n over. CH-1 delta count test OK.

(09)Verify BIOS ROM checksum, fl ush external cache.

Award (09)Program the configuration register of Cyrix CPU. OEM specific cache initialization., Early Cache initialization; Cyrix CPU initialization; cache initialization. Test CMOS RAM checksum; beep; also test extended storage of para meters in the motherboard chipset;if not warm- booting;displa y the Test CMOS

RAM checksum message, if bad, or insert key pressed, load defaults if bad. Check

BIOS Checksum.

Chips & Tech (09)Unexpected interrupt is occurring.

Phoenix&Dell (09)Set POS T flay.(Beep)=1-1-3-2. 1st 64K RAM test in-progress.

Error Code – 0A

AMI (0A)CMOS initialization done(if any). Keyboard command byte code is issued.

Award

Going to write command byte data. Go - ing to write command byte data. CH -0 of timer initialization over. CH-0 delta count test OK

(0A)Initialize the first 32 interrupt vectors. Initialize INTs 33 to 120.Early Power

Management initialization. Setup interrupt vector table in lower 1K RAM area;

Initialize first 120 interrupt vectors with SPURIOUS_INT_HDLR and initialize I NT

00h-1Fh according to INT_TBL. Initialize key - board; Detect type of keyboard controller(optional 8242 or 8248, with Nedadon XOR gate control); Set

NUM_LOCK status. Reset keyboard test keyboard controller interface to verify it returned AAH and responded to enable/disable commands,set ke yboard buffer, enable keyboard and keyboard interrupts for normal use, beep, halt .Initialize Video controller.

Chips & Tech (0A)Timer cannot interrupt.

Phoenix&Dell (0A)Initialize CPU registers. (Beep)=1 -1-3-3. Perform BIOS checksum test. 1st 64K

RAM chip or data line failure multi -bit.

Error Code – 0B

Appendix A

AMI

Award

CMOS status register initialize done. Keyboard controller command byte is written.

Going to issue Pin-23,24 blocking/ unblockin g command. Going to issue pin-23,24 blocking/nubolcking command. Refresh started. Parity status cleared

(0B)Verify the RTC time is valid or not. Detect bad batt ery. Read CMOS data into

BIOS stack area. Perform PnP initializations. Assign I/ O & Memor y for PCI devices

(PCI BIOS Only). Test CMOS RAM checksum; beep; also test extende d storage of parameters in the motherboard chipset; if not warm -booting,displa y the Test CMOS

RAM checksum message, if bad, or insert key pressed,load defaults if bad.

Initialize video interface; Detect C PU clock; Read CMOS location 14b to find out type of video in use; Detect and initialize vid eo adapter. 8254 timer,channel 0 test.

Chips & Tech (0B)CPU protected mode.

Phoenix&Dell (0B)Enable CPU Cable -Check CPU Jumpers. [Beep]=1 -3-4 1st 64K RAM odd/even

AMI logic failure.

Error Code – 0C

(0C)KB controller I/B free. Going to issue the BAT command to keyboar d controller.

Award

Pin-3,24 of ke yboard controller is blocked/unblocked. NOP command of keyboard controller to be issued next. NOP command of key - board controller to be issued next. System timer started. Refresh & system timer OK

(0C)Initialization of the BIOS data area(40:00 -40:FF). Initialize keyboard; Detect type of keyboard controller (optional 8242 or 8248, with Nedadon XOR gate control); Set NUM_LOCK status. Reset keyboard test keyboard controller interface to verify it returned AAH and responded to enable/disable commands, set keyboard buffer, enable keyboard and keyboard interrupts for normal use,beep,halt.8254 timer,channel 1 test.

Chips & Tech (0C)DMA register failure.

Phoenix&Dell (0C)Initialize cache to initi al POST value. Test DMA page registers. [Beep]=1 -4-1

AMI

1st 64K RAM address line failure.

Error Code – 0D

(0D)BAT command to keyboard controller is issue d. Going to verify the BAT command. NOP command processing is do ne.CMOS shutdown register test to be done next. CMOS shutdown register test to be done next. Refresh link toggling

AST passed. Refresh link toggling passed.

(0D)(Beeps)=13 short,8254 timer r egister.

Chips & Tech (0D) (Beeps)=14 short, Refresh failure.

Award (0D)Program some of the chipset’s value. Measure CPU spee d for display. Video initialization including MDA, CGA,EGA/VGA. Initialize video interface; Detect

CPU clock; Read CMOS location 14b to find out type o f video in use; Detect and initialize video adapter. OEM specific -Initialize motherboard special chipset as required by OEM; initialize cache controller earl y, when cache is separate from chipset.8254 timer,channel 2 test.

Phoenix&Dell (0D)[Beep]=1-4-2 1st 64K RAM parity test in progress or failure.

Error Code – 0E

AST (0E)(Beeps)=14 short,ASIC registers.

AMI

Award

(0E)Keyboard controller BAT result verified. An y initialization after KB controller

BAT to be next. C MOS shutdown regist er R/W test passe d. Going to calculate

CMOS checksum,and update DIAG. Goint to calculate CMOS checks um,and update

DIAG Byte. Refresh period ON/OFF 50% OK

(0E)Initialize the APIC(Multi -Processor BIOS only). Test video RAM(If

Monochrome display device found). Show startup s creen message. Test video memory; Test video memory, write sign -on message to screen. Setup shadow

RAM-Enable shadow accor ding to setup. Test COMS Shutd own byte.

Chips & Tech (0E)(Beeps)=14 short, Keyboard controller failure.

Phoenix

AMI

(0E)Initialize I/O.( Beep)=1-1-4-3. Test 8254 timers.

Error Code – 0F

(0F)initializati on after KB controller BAT done. Keyboar d command byte to be

AST

Award written next. CMOS checksum calculation is done, DIAG byte written. CMOS Init.

To begin(If “INIT CMOS IN EVERY BOOT IS SET”).CMOS initialization to begin(If “INIT CMOS IN E VERY BOOT IS SET”).

(0F)(Beeps)=15 short,CMOS RAM shutdown.

(0F)DMA channel 0 Test. Test DMA controller 0; BIOS checksu m test, keyb oard detect and initializati on.Test Extended CMOS.

Chips & Tech (0F)(Beeps)=15 short,Protected mode failure.

Phoenix (0F)Initialize the local IDE

AMI

Error Code – 10

(10)KB controller command byte is written. Going to issue pin -23,24 blocking/unblocking command. CMOS initia - lization done(if any). CMOS status register about to Init for Date and Time. CMOS status register about to Init for Date and Time. Refresh on and about to start 64K base m emory test. Confirmed refresh

ON & about to start 64 K memory.

Appendix A

AST

Award

(10)DMA controller test 0 register

(10)DMA channel 1 Test. Test DMA controller 1 with AA, 55, FF,00 pattern.8237

DMA,channel 0 test.

Compaq (10)PPI disabled, Program timers 0 & 1.

Chips & Tech (10)(Beeps)=19 short, IDT,GDT failure.

Phoenix&Dell (10)Initialize Power Management.(Beep)=1 -2-1-1.Initia- lize 8254

AMI timers.[Beep]=2-1-1 1st 64K RAM chip or data line failure -bit 0.

Error Code – 11

(11)Pin23,24 of keyboard controller is blocked/unblocked. Going to check to check pressing of <INS>key during power -on.CMOS status register initialized.Going to

AST

Award disable DMA and Interrupt controllers. Going to disable DMA and interrup t controllers. Address line test passed. Address line test passed.

(11)DMA controller test r egister 1.

(11)DMA page register test. Test DMA page register s,use I/O ports to test address circuits. POST enabl es user reboot here.Test DMA page regist ers. FATAL DISPLAY

ER- RORS.8237 DMA,channel 1 test.

Compaq (11)Init(blast)VDU controllers.

Chips & Tech (11)Register LDT failure.

Phoenix&Dell (11)Load alternate registers with POS T values.(Beep)=1 -2- 2. 1st 64K RAM chip or

AMI data line failure-bit 1.

Error Code – 12

(12)Checking for pressing of <INS>key during power-on done. Going to disable

DMA and Interrupt controllers.D MA controller#1,#2,int errupt controller#1,#2 disabled. About to disable Video display and Init port -B. About to disable video display and Init port -B.64K base memory test passed. 64K base memory test passed.

(12)DMA page registers test. AST

Award (12)Call support 800 -909-3424. Test 8254 timer 0 chann el 0. Test DMA page registers.

Compaq (12)Clear screen, turn on video.

Chips & Tech (12)Task register failure.

Phoenix&Dell (12)Restore CPU control word during warm boot. Jump to User Path

AMI

0.(Beep)=1-2-1-3.Test both 8237 DMA controllers. 1st 64 K RAM chip or data line failure-bit 2.

Error Code – 13

(13)DMA controller#1,#2 ,interrupt controller#1,#2disa - bled. About to disable

Video displa y and initialize port-B. Chipset initialize/auto memory detection about to begin. Replace first memory SIMM.(13)Chipset in itialize/auto memory detection about to begin. Check first SIMM.(13) Interrupt vectors initialized.

(13)Initialize video.

(13)Test 8254 timer 0 channel 1. Test keyboard con troller.

AST

Award

Compaq (13)Test timer 0.

Chips & Tech (13)LSL instruction failure.

Phoenix&Dell [Beep]=2-1-4 1st 64K RAM chip or data line failure -bit 3. Initialize PCI Bus

Mastering devices.

Error Code – 14

ACER (14)DMA Controller.

AMI (14)Chipset initiali zation/auto me mory detection over. To un-compress the POST code if compressed BIOS.8254 timer test about to start.8254 timer test about to start.8042 keyboard controller test OK.

AST

Award

(14)Memory refresh test.

(14)Test 8254 timer 0 counter 2. Test timer c ounter 2; Test 8254 ti mer 0 counter 2.

Compaq

Test memory refresh.

(14)Disable RTC interrupts.

Chips & Tech (14)LAR failure.

Phoenix&Dell (14)Initialize keyboard controller.(Beep)=1 -2-2-1.Initialize 823 7 DMA

AMI controllers.[Beep]=2 -2-1 1st 64K RAM chip or data line failure -bit 4.

Error Code – 15

(15)POST code is un-compressed.8254 timer about to start. CH -2 timer test

Award halfway.8254 CH-2 timer test to be complete.8254 CH -2 timer test to be completed.

Interrupt vectors initialized. CMOS read/write test OK.

(15)test 8259 interrupt mask bits for c hannel 1. Test 8259-1 mask bits; Verify 8259 channel 1 masked interrupt by alternate turni ng off and on the interrupt line. Test 1st

64K of syste m memory.

Compaq (15)Check battery power.

Chips & Tech (15)VERW/VERR failure.

Phoenix&Dell (15)[Beep]=2-2-2 1st 64K RAM chip or data line failure-bit 5.

Error Code – 16

AMI (16)CH-2 timer test over.8254 CH -1 timer test to be complete. CMOS checksum/batter y check OK

Appendix A

Award

Compaq

(16)Test 8259-2 mask bits; Verify 8259 channel 2 masked interr upt by alternate turning off and on the interrupt line. Setup Interrupt vectors.

(16)Battery power was lost.

Chips & Tech (16)Keyboard controller gate A20 failure.

Phoenix&Dell (16)BIOS ROM checksum.(Beep)=1 -2-2-3. Initialize 8259, reset

AMI

Coprocessor.[Beep]=2-2-3 1st 64K RAM chip or data line failure-bit 6.

Error Code – 17

(17)CH-1 timer test over.8254 CH -0 timer test to be completed. Monochrome mode

Award set.

(17)Test struck 8259’s interrupt bits; Turn off interrupt then verify no interr upt mask

Compaq register is on. Setup video I/O op erations.

(17)Cler CMOS-DIAG

Phoenix&Dell (17)Initialize cache before memory auto -size.[Beep] =2-2-4 1st 64K RAM chip or data line failure-bit 7.

ACER

AMI

AST

Award

(18)Timer initialize.

(18)CH-0 timer test over. About to start memory re fresh. Color mode set.

(18)Testing Video memory.

Error Code – 18

(18)Test 8259 interrupt functionality; Force an interrupt and verify the interrupt

Dell occurred. Test video memory.

(18)[Beep]= 2-3-1 1st 64K RAM chip or data line failure - bit 8

Compaq (18)Test base memory(first 128K)

Chips & Tech (18)Shutdown during memory test.

Phoenix&Dell (18)8254 timer initialization.(Beep)=1 -2-3-1. Test 8259 interrupt controllers

AMI registers.[Beep]=2-3-1 1st 64K RAM chip or data line failure -bit 8.

Error Code – 19

(19)82 timer test over. Memory refresh test to be done next. About to look for

Award optional video ROM at segment C000 and give control to the optional video ROM if present.

(19)Test 8259 functionali ty. Test stuck NON-Maskable Interrupt bits(Parity/I/O check);Verify NMI can be cleared. 8259 Interrupt controll er, channel 1 mask bits

Compaq test.

(19)Clear and initialize base memor y.

Phoenix&Dell (19)check memory[Beep]=2 -3-2 1st 64K RAM chip or data line failure -bit 9.

Error Code – 1A

AMI (1A)Memory r efresh line is toggling. Going to check 15 micro second ON/OFF time. Return from optional video ROM. Optional video ROM control OK

Award

Compaq

(1A)Display CPU clock.8259 Interrupt controller, channel 2 mask bits test.

(1A)Initialize and test VDU adapter s.

Chips & Tech (1A)Copyright checksum errors.

Phoenix&Dell (1A)8237 DMA controller initialization.(Beep)=1 -2-3-3. Verify refres h is occurring.[Beep]=2-3-3 1st 64K RAM chip or data line failure -bit A.

AMI

Error Code – 1B

(1B)Memory refresh period 30 m icro second test complete. Base 64K memory test about to start. Shadow RAM enable /disable completed. Display memory read/write test OK.

Award (1B)Test CMOS battery status. Test the system ROM.

Chips & Tech (1b)Shutdown during memory sizing.

Phoenix&Dell (1B)[Beep]=2-4-1 1st 64K RAM chip or data line failure - bit B.

ACER (1C)Memory refresh.

Error Code – 1C

AMI (1C)Display memory read/write test for main display type as set in the CMOS setup program over. Display memory read/write test for alternate d isplay OK.

Award (1C)Test CMOS RAM checks um. Test CMOS.

Chips & Tech (1C)Chip-Set initialization.

Phoenix&Dell (1C)[Beep]=2-4-1 1st 64K RAM chip or data line failure - bit C.Reset Progra mmable

Interrupt Controller.(Beep)=1 -2 –4-1.Base 64K address test.

AMI

Error Code – 1D

(1D)Display memory read/write test for alternate display type complete if main display memor y read/write test returns error. Video retrace check OK. Set configuration from CMOS.

Compaq (1D)Test DMA controller a nd page registers.

Phoenix&Dell (1D)[Beep]=2-4-2 1st 64K RAM chip or data line failure - bit D

ACER

AMI

Award

Compaq

(1E)Select memory type.

(1E)Test keyboard controller.

Error Code – 1E

(1E)Global equipment byte set for proper display type.

(1E)If EISA NVM checksum is good, execute E ISA initialization(EISA BIOS

ONLY). Size s ystem memory.

Appendix A

Phoenix&Dell (1E)[Beep]=2-4-3 1st 64K RAM chip or data line failure - bit E.Base 64K RAM test(16 bits).

Error Code - 1F

AMI (1F)Video mode set call for mono/color begins. Mode set call for mono/color OK.

Set EISA mode; If EISA non - volatile memory checksu m is good, execute EISA initialization. If not, exe cute ISA test an clear EISA mode flag. Test EISA configuration memory integrit y(checksum & comm.- unication interface).

Award

Compaq

(1F)Test system memor y.

(1F)Test 286 protected mode.

Phoenix&Dell (1F)[Beep]=2-4-4 1st 64K RAM chip or data line failure - bit F.

ACER

AMI

AST

Award

Compaq

Error Code – 20

(20)Test 128K.

(20)Memory refresh period 30 micro second test complete. Base 64K memory/address test started. Address line test to be done next. Video mode set completed.

(20)Power up bus boar d(EISA only).

(20)Enable slot 0;Initialize slot 0(system board).(Check memory size).8259 stuck bits test.

(20)Test real and extende d memory.

Phoenix&Dell (20)[Beep]=3-1-1 master DMA register test in -progress or failure. Test DRAM refresh.(Beep)=1-3-1-1. Upper 16 of 32 bit test failed.

AMI

Error Code – 21

(21)Address line test passed. Going to do toggle parit y. (21)ROM t ype 27256

Award

Compaq verified. Video display OK.

(21)Enable slots 1 through 15;Initialize slot 1.Test stuck NMI bits (parity I/O check).

(21)Init time-of-day.

Phoenix&Dell (21)[Beep]=3-1-2 slave DMA register test in -progress or failure.

AMI

Award

Error Code – 22

(22)Toggle parity over. Going for sequential data R/W test on 64 K memory. Power on message displa y OK.

(22)Enable slots 2; Initialize sl ot 2.Test 8259 workin g.

Compaq (22)Init 287 Coprocessor.

Phoenix&Dell (22)[Beep]=3-1-3 master interrupt mask register test in- progress or fail. Test 8742

AMI

Award

Compaq keyboard controller.(Beep)=1 - 3-1-3

Error Code – 23

(23)Base 64K sequential data R/W test passed. Going to SET BIOS stack and to do any setup before Interrupt vector Init. Any setup before interrupt vector Init about to start. Power on message displayed.

(23)Enable slots 3;Initialize sl ot 3.Test protected mode.

(23)Test keyboard and interface.

Phoenix&Dell [Beep]=3-1-4 slave interrupt mask register test in -progress or fail.

Error Code – 24

ACER

AMI

(24)Test keyboard contr oller(8042).

(24)Setup required before vector initialization complete. Interrupt vector

Award

Compaq

Phoenix initialization about to begin.

(24)Enable slots 4;Initialize slot 4.Size exte nded memory.

(24)reset A20 ads set default CPU speed .

(24)Set ES segment to register to 4 GB.(beep)=1 -3-2-1. Verify CMOS/Configur e

CMOS.

AMI

Error Code – 25

(25)Interrupt vector initialization done. Going to read Input port of 9042 for turbo

Award

Compaq switch(if any).Going to read I/O port of 8042 for turb o switch(if any).

(25)Enable slots 5;Initialize slot 5.Test extended memor y.

(25)Test diskette subsystem.

Phoenix&Dell (25)[Beep]=none interrupt vector loading in -progress.

AMI

Error Code – 26

(26)I/O port of 8042 is read. Going to initi alize global data for turbo switch. Going to

Award

Compaq initialize global data for turbo switch.

(26)Enable slots 6;Initialize slot 6.Test protected mode exceptions.

(26)Test fixed disk subsystem.

Phoenix 6.0 (26)Enable A20 line. Verify/Load NVRAM par ameters.

AMI

Error Code – 27

(27)Global data initialization for turbo switch is over. Any initializati on before

Award

Compaq setting video mode to be done next.

(27)Enable slots 7; Initialize slot 7.Setup cache control or shadow RAM.

(27)initialize parallel prin ter.

Phoenix&Dell (27)[Beep]=3-2-4 keyboard controller test in -progress or failure.

Error Code – 28

ACER (28)Test CPU.

Appendix A

AMI

Award

(28)initialization before settin g video mode is complete. Going for monochrome mode and color setting .Check extended memory.

(28)Enable slots 8;Initialize slot 8. Setup 8242.

Compaq (28)Perform search for option ROMs

Phoenix&Dell (28)[Beep]=3-3-1 CMOS power-fail and checksum checks in -progress. Auto-size

DRAM.(Beep)=1-3-3-1.Protected mode 1.

Error Code – 29

AMI

Award

Compaq

(29)Monochrome mode setting is done. Going for color mode setting.

(29)Enable slots 9;Initialize slot 9.

(29)Test for valid system configuration.

Phoenix&Dell (29)[Beep]=3-3-2 CMOS configuration info validation in - progress. Initiali ze POST

Memory Ma nager.

AMI

Error Code – 2A

(2A)monochrome Color mode setting is done. About to go for toggle parity before

Award

Compaq

Phoenix optional rom test. About to go for toggle parity before optional ROM Check.

(2A)Enable slots A; Initialize slot A.(2A)8242 in itialization.

(2A)Clear screen.

(2A)Clear 512K base RAM.(Beep)=1 -3-3-3.Aubo-site memory chips.

Error Code – 2B

AMI (2B)Toggle parity over. About to give control for any setup required before opti onal video ROM check.

Award

Compaq

(2B)Enable slots B; Initialize slot B. Initialize floppy drive and controller.

(2B)Check for invalid time and date.

Phoenix&Dell (2B)[Beep]=3-3-4 screen memory test in -progress or failure.

Error Code – 2C

ACER

AMI

Award

Compaq

Dell

(2C)Set up interrupt controller(8259).

(2C)Processing before video ROM control is done. About to look for optional video

ROM and give control.

(2C)Enable slots C;Initialize slot C.Detect & initialize serial ports.

(2C)Boot.

(2C)[Beep]=3-4-1 screen initialization in-progress or failure.

Phoenix (2C)RAM failure on address xxxx.If the BIOS detects error 2C,2E,or 30(base 512K

RAM error),it displays and additional word -bitmap(xxxx)indication the address line

Award

Dell

Phoenix or bits that failed. For example, “2C 0002”means addressline 1 (bit one set) has failed. “2E 1020 means data bits 12 and 5 (bits 12 and 5 set) have failed in the lower

16 bits. Note that error 30 cannot occur on 386SX systems because they have a 16 rather than 32-bit bus. The BIOS also sends the bitmap to the port -80 LED disp lay. It first display the check point code, followed b y a delay, the high-order byte, another delay, and then the low -order byte of the err or. It repeats this sequence continuously.

Test 512 base address li nes.(Beep)= 1-3-4-1 Activate interleave(if

AMI possible).[Beep]3-4-1 screen initialization in-progress or failure.

Error Code – 2D

(2D)Optional video ROM control is done. About to give control to do any processing after video ROM returns control.

Award (2D)Enable slots D; Initialize slot D. Detect & i nitialize parallel ports. Test timer 2.

Phoenix& Dell (2D)[Beep]=3-4-2 screen retrace tests in-progress or failure.

AMI

Error Code – 2E

(2E)Return from processing after t he video ROM control. If EGA/VGA not found then do display memor y R/W test.

(2E)Enable slots E; Initialize slot E. Initialize hard dri ve & controller.

(2E)[Beep]=3-4-3 search for video ROM in -progress.

AMI

Award

Compaq

Phoenix

ACER

AMI

(2E)See Error code “2C”.Test 512K base memory.(Beep)= 1-3-4-3.Exit 1st protected mode test.[Beep]=none search for video ROM in-progress.

Error Code – 2F

(2F)EGA/VGA not found. Displa y memory R/W test about to begin.

(2F)Enable slots F; Initialize slot F. Detect & initializ e 80x87 Co-Processor.

(2F)Write to DIAG byte.

(2F)Enable cache before system BIOS shadow.

Error Code – 30

(30)Set up Temp. interrupt.

(30)display memor y R/W test passed. About to look for the retrace checking. Virtual

AST

Award

Compaq

Dell

Phoenix mode memory test about to begin.

(30)Interrupt controller#1.

(30)Get base memor y & extended memory size. Size base And extended memory from 256K to 640K and extended memory above 1MB.

(30)Clear 1st 128K bytes of RAM.

(30)[beep]=none screen believed running w/video ROM.

(30)see Error Code “2C”.Unexpected shutdow n.[Beep]=none screen believed operable. [Beep]=none screen believed running w/video ROM.

Appendix A

AMI

Error Code – 31

(31)Display memory R/W test or retrace checking failed. About to do alternate

Display memor y R/W test. Virtual mode memory test started.

AST

Award

(31)Interrupt controller#2.

(31)Test base and extended memory; Test base memor y from 256K to 640K and extended memory above 1MB using various patterns. Detect & initialize optional

ROMs.

Compaq (31)Load interrupt vectors 70 -77.

Phoenix&Dell (31)[Beep]=none monochromatic screen believed operable.

Error Code – 32

AMI

AST

Award

Compaq

Dell

Phoenix

(32)Alternate display memory R/W test passed. About to look for the alternate display retrace checking. Processor executing in virtual mode.

(32)Interrupt controllers for stuck interrupt.

(32)Display the Award Plug & Pla y BIOS extension message(PnP BIOS only).Test

EISA extended memory; If EISA mode flag is set then test EISA memory found in slots initialization, T his test is skipped in ISA mode and can be skipped with ESC key in EISA mode.

(32)Load interrupt vectors 00 -1F.

(32)[Beep]=none 40-column color screen believed operable.

(32)Test CPU bus-clock frequenc y.(Beep)=1-4-1-3.Deter- mine system board memory size.

AMI

[Beep]=none 40-column color screen be lieved operable.

Error Code – 33

(33)Video display checking over. Verification of display type with switch setting and actual card to begin. Verification of display type with switch setting and Actual Card

AST

Award

Compaq to begin. Memory address line test in progr ess.

(33)Non-maskable interrupt for stuck interrupt(EISA,P486, P386)

(33)Call Tech Support 727 -532-4151.

(33)Initialize Memor y SIZE and RESETWD.

Phoenix&Dell (33)[Beep]=none 80 -column color screen believed operable. Initialize dispatch

Manager.

ACER (34)Set up BIOS interr upt vector.

Error Code – 34

AMI (34)Verification of display adapter done. Display mode to be set next. Memory address line test in progress.

Compaq (34)Verify CMOS checksum.

Phoenix&Dell (34)[Beep]=4-2-1 timer tick interrupt test in progress or failure. Relocate memory option.

AMI

Error Code – 35

(35)Display mode set complete. BIOS ROM data area about to be checked. Memory

Compaq below 1MB calculated.

(35)CMOS checksum not valid.

Phoenix&Dell (35)[Beep]=4-2-2 shutdown test in progress or failure.

AMI

Error Code – 36

(36)BIOS ROM data area check over. Going to set cursor for power on message.

Compaq

Memory above 1MB calculated.

(36)Check battery power.

Phoenix&Dell (36)[Beep]=4-2-3 gate A20 fail ure. Warm start shut down. Configure EMS memory option.

AMI

Error Code – 37

(37)Cursor setting for power on message id complete. Going to display the power on

Compaq message. Memory test about to start.

(37)Check for game adapters.

Phoenix&Dell (37)[Beep]=1-4-2-4 unexpected interrupt in protected mode. Reinitialize the motherboard chipset.

ACER

AMI

(38)CMOS RAM.

Error Code – 38

(38)Power on message display complete. Going to read new cursor position.

Compaq

Memory below 1MB initialized.

(38)Check for serial p orts.

Phoenix&Dell (38)[Beep]=4-3-1 RAM test in progress or failure above address 0FFFFh

Phoenix

AMI

(38)Shadow system BIOS ROM.(Beep)=1 -4-3-1.Configure wait state option.

Error Code – 39

Compaq

Phoenix

AMI

(39)New cursor position read and saved. Going go display the Hi t<DEL>message.

Memory above 1MB initialized.

(39)Check for parallel ports.

(39)Reinitialize the cache.(Beep)=1 -4-3-1

Error Code – 3A

(3A)Check memory, first 64K,one long beep. Reference string displa y is over. Going

Appendix A

Award to display the Hit<ESC> massage. Memory size display initiated. This will be updated when the BIOS goes through the memory.

(3A)Check me mory.

Compaq (3A)Initialize Port. And comm. timeouts.

Phoenix&Dell (3A)[Beep]=4-3-3 Interval timer channel 2 test in progress o r failure.

Phoenix

AMI

(3A)Auto-size cache.(Beep)=1-4-3-3.Retest 64K base RA M.

Error Code – 3B

(3b)Hit<DEL>or<ESC>message displa yed. Virtual mode memory test about to start,

About to start below 1MB memory test.

Compaq (3B)Flush ke yboard buffer.

Phoenix&Dell (3B)[Beep]=4-3-4 Time-Of-Day clock test in progress or failure.

Error Code – 3C

ACER

AMI

(3C)Memory size.

(3C)Memory test below 1MB completed and about to start above 1MB test.

Award

Phoenix

(3C)Set flag to allow users to enter C MOS setup utility. Setup enabled.

(3C)Configure advanced chipset registers.(Beep)=1 -4-4-1. Determine relative CPU speed.

Phoenix&Dell (3C)[Beep]=4-4-2 Serial port test in progress or failure.

Error Code – 3D

AMI

Award

(3D)Memory test above 1MB completed.

(3D)Initialize keyboard. Install PS/2 mouse. Initialize & install mouse; Detect if

Phoenix mouse is present, initialize mouse, install interrupt vectors.

(3D)Load alternate registers with CMOS values,(Beep)= 1 -4-4-2

Phoenix&Dell (3D)[Beep]=4-4-2 Parallel port test in progress or failure.

AMI

Award

Error Code – 3E

(3E)About to go to real mode(shutdown).

(3E)Try to turn on level 2 cache.,

Phoenix 3.07 (3E)Get switches/jumper status from 8742.

Phoenix&Dell (3E)[Beep]=4-4-3 Math CoProcessor test in progress o r failure.

Error Code – 3F

AMI (3F)Shutdown successful and Processor in real mode.

Award (3F)Enable shadow RAM per CMOS RAM setup or if ME - MORY TYPE is SYS in the EISA configuration.

Dell

ACER

AMI

AST

Award

Compaq

Phoenix

AMI

AST

Award

Compaq

AMI

(3F)Cache memory failure.

Error Code – 40

(40)Shutdown#1.

(40)Preparation for virtual mode test starte d. Going to verify from video memory.

CACHE memory on and about to disable A20 address line.

(40)CMOS RAM backup batter y.

(40)Display virus protest disable or enable.

(40)Save RESET WD value.

(40)Set initial CPU speed.(Beep)=2 -1-1-1.

Error Code – 41

(41)Returned after verifying from displa y memory. Going to prepare the descriptor bables.A20 address line disabled successful.

(41)CMOS RAM checksum.

(41)Initialize floppy disk drive controller.

(41)Check RAM refresh.

Error Code – 42

(42)descriptor tables prepared. Going to enter in virtual mode for memory test.486 internal cache turned on. About to start DMA controller t est.

AST

Award

Compaq

Phoenix

AMI

Award

Compaq

ACER

AMI

Award

Compaq

Phoenix

(42)Setup CMOS RAM.

(42)Initialize hard drive & controller; Initialize hard drive controller and an y drives.

(42)Start write cycle of 128K RAM test.

(42)Initialize interrupt vectors.(Beep)=2 -1-1-3.

Error Code – 43

(43)Entered in the virtual mo de. Going to enable interrupts for diagnostics mode.

About to start DMA controller test.

(43)If it is a PnP BIOS, initialize serial & parallel ports. Detect & initialize serial/parallel ports; Initialize any serial and parallel ports (also game port ).

(43)Reset parity checks.

(44)Video BIOS ROM initialize.

Error Code – 44

(44)Interrupts enabled(if post switch is on). Going to initialize data to check memo ry wrap around at 0:0.

(44) Going to initialize data to check memory re-map at 0:0.

(44)Start verify cycle if 128K RAM test.

(44)Initialize BIOS interrupts.(Beep)=2 -1-2-1. Verify video con figuration.

Error Code – 45

Appendix A

ACER

AMI

Award

Compaq

Phoenix

ACER

AMI

Award

Compaq

Phoenix

AMI

Award

ACER

AMI

Phoenix

AMI

Phoenix

AMI

Phoenix

AMI

Phoenix

ACER

AMI

Phoenix

AMI

Award

Compaq

Phoenix

(45)Set up BIOS RAM .

(45)Data initialized. Going to check for memory wrap arou nd at 0:0 and the total system memory size.

(45)Detect & Initialize math CoProcessor; Initialize math CoProcessor.

(45)Check for parity errors.

(45)POST device initialization.

Error Code – 46

(46)Test controller and cache me mory.

(46) Memory wrap around test done. Memory size calculation over, writing pat terns to test me mory.

(46)display the setup message(to press Ctrl -Alt-Esc to enter setup), and enable setup.

(46)No RAM errors.

(46)Check ROM cop ying notice.(Beep)=2-1-2-3. Initialize video system.

Error Code – 47

(47)Pattern to be tested written in extende d memory,640K memory.

(47)Set system speed for boot.

(47)Got a RAM error.

(47)Initialize manager for PCI Options ROMs.(Beep)=2-1- 2-4.

Error Code – 48

(48)Memor y test.

(48)Patterns written in base memor y. Going to find out amount of memory below

1M memor y.

(48)Check Video confi guration against CMOS.(Beep)=2 - 1-3-1. Test for unexpect ed interrupts.

Error Code – 49

(49)Memory below 1M found and verified. Going to find out amount of memory above 1M me mory.

(49)Initialize PCI bus and devices.(Beep)=2 -1-3-2.

Error Code – 4A

(4A)Amount of memory above 1M found and verified. Going for BIOS ROM data area check.

(4A)Initialize all video adapters in system.(Beep)=2 -1-3-3. Start 2nd protected mode test.

Error Code – 4B

(4B) Amount of memory above 1M found and verified. Check for soft reset and going to clear memory below 1M for reset.(If power on, go to check point#4Eh).BIOS ROM data area check over. Going to check<ESC> and to clear memory below 1M for soft reset.

(4B)Quiet-Boot start(optional).

Error Code – 4C

(4C)#3 shutdown.

(4C)Memory below 1M cl eared.(SOFT RESET)Going to clear memor y above 1M.

(4C)Shadow video BIOS ROM.(Beep)=2 -1-4-1.Perform LDT instructions test.

Error Code – 4D

(4D)Memory above 1M cleared. (SOFT RESET)Going to save the memory size.(GOTO check point#52h)

Error Code – 4E

(4E)Memory test started.(NO SOFT RESET)About to display the first 64K memory test.

(4E)If there is any error, show all the error messages on the screen & wait for user to press<F1>.Manufacturing POST loop or display messages; Reboot i f manufacturing

Phoenix

AMI

Award

ACER

AMI

POST loop pin is set. Otherwise display any messages and enter setup.

(4E)Display copying notice.(Beep)=2 -1-4-3. Perform TR instruction test.

Error Code – 4F

(4F)Memory size display started. This will be updated during memor y test. Going for sequential and random memory test. Processor in real mode after shutdown.

(4F)If password is needed, ask for password. Clear the Energy Star logo(Green BIOS only).Security ch eck; Ask password securit y.

Error Code – 50

(50)#2 shutdown.

(50)Memory testing/initialization below 1M complete. Going to adjust displayed

AST memory size for relocati on /shadow. DMA page register test complete.

(50)Protected mode.

Award (50)Write all the CMOS values currentl y in the BIOS stack areas back into the

CMOS. Write CMOS; Write all CMOS values back to RAM and clear scre en.

Compaq (50)Check for dual freq in CMOS.

Chips & Tech (50)Hardware initialize.

Phoenix (50)Display CPU type and speed.(Beep)=2 -2-1-1.(50)Per- form LSL instruction test.[Beep]=none Custom chip set or custom platform.

Appendix A

AMI

Error Code – 51

(51)Memory size display adjusted due to relocation/shadow. Memory test above 1M to follow. DMA unit-1 base register test about to start.

AST

Award

Compaq (51)Check CMOS VDU configuration.

Chips & Tech (51)Timer Initialize

Phoenix

AMI

(51)Protected mode.

(51)Pre-boot enable; Enable parity checker; Enable NMI, Enable cache before boot.

(51)Initialize E ISA board.

Error Code – 52

(52)Memory testing/initialization below 1M complete. Going to save memory size

Award information. Going to prepare to go back to real mode. DMA un it-1 channel OK, about to begin CH-2.

(52)Initialize all ISA ROMs. Later PCI initializations(PCI BIOS only).PnP initializations(Pn P BIOS only).Program shadow RA M according to setup settings.

Program parity according to setup setting. Power Management initialization.

Initialize option ROMs; initialize any option ROMs present from C8000h to

Compaq

EFFFFh.

(52)Start VDU search.

Chips & Tech (52)DMA controller init ialize.

Phoenix (52)Test keyboard.(Beep)=2 -2-1-3.(52)Perform LAR instruction test.

Error Code – 53

AMI

Award

(53)Memory size information is saved. CPU registers are saved. Going to enter in real mode. DMA CH -2 base register test OK.

(53)If it is not a PnP BIOS, initialize serial & parallel ports. Initialize time value in

BIOS data area. Initialize time value; Initialize time value in 40h BIOS data area.

Compaq (53)Vector to VDU opt ion ROMs.

Chips & Tech (53)Initialize interrupt controller.

Error Code – 54

ACER

AMI

(54)#7 shutdown.

(54)Shutdown successful, CPU in real mode. Going to re - store registers saved during preparation for shutdown. About to check F/F latch for unit -1 and unit-2.

Compaq (54)Initialize primar y display adapter.

Chips & Tech (54)Chip-Set Initialize.

Phoenix

AMI

(54)Set key click if enabled.(Beep)=2 -2-2-1.(54)Perform VERR instruction test.

Error Code – 55

(55)Registers restored. Going to disable gate A20 address line. F/F latch for both units checked.

Award

Compaq

(55)Check PCI video Card-or replace video card.

(55)Initialize secondar y display adapter.

Chips & Tech (55)EMS configuration Setup.

AMI

Error Code – 56

(56)A20 address line disable successful. BIOS ROM data area about to be checked.

DMA unit 1 and 2 programm ing over and about to initialize 8259 interrupt controller.

Compaq (56)No display adapters installed.

Chips & Tech (56) Protected mode.

Phoenix

AMI

(56)Enable keyboard.(Beep)=2 -2-2-3.Unexpected exception.

Error Code – 57

(57)A20 address line disable successful. BIOS ROM data area chec k halfway. BIOS

Compaq

ROM data area check to be com - plete.8259 initializa tion over.

(57)Init primary VDU mode.

Chips & Tech (57)Memor y size.

ACER

AMI

(58)#6 shutdown.

Error Code – 58

(58)Memory size adjusted for relocation/shado w. Going to clear Hit<DEL> message. BIOS ROM data area check over. Going to clear Hit<ESC > message.8259 mask register check OK.

Compaq (58)Start of VDU test (for each adapter).

Chips & Tech (58)Memory interleave configure.

Phoenix (58)Test for unexpected interrupts.(Beep)=2 -3-3-.(58) Perform A20 gate test.

Error Code – 59

AMI (59)Hit<ESC> message cleare d.<Wait..> messa ge displayed. About to start DMA and interrupt controller test. Master 8259 mask register OK, about to start slave.

Compaq (59)Check existence of adapter.

Chips & Tech (59)Exiting protected mode.

Phoenix (59)Initialize POST display service.

Error Code – 5A

AMI

Compaq

(5A)About to check timer and keyboard interrupt level.

(5A)Blank displa y, check VDU registers.

Appendix A

Chips & Tech (5A)Board memory size.

Phoenix (5A)Keyboard ready test. Display prompt “press F2 to enter

SETUP”.(Beep)=2-2-3-3

AMI

ACER

Compaq

(5B)Timer interrupt OK.

(5B)Start screen memory test.

Chips & Tech (5B)Shadow RAM relocated.

Phoenix (5B)Display CPU cache.

Error Code – 5B

Error Code – 5C

(5C)About to test keyboard and I/O.`

AMI

Compaq

(5C)About to test keyboard interrupt.

(5C)End of test of adapter, clear memor y.

Chips & Tech (5C)EMS configure.

Phoenix (5C)Test RAM between 512 and 640K.(Beep)=2-2-4-1. Determine if AT or KT keyboard t ype.

AMI

Compaq

Error Code – 5D

(5D)ERROR! Timer/keyboard interrupt not in proper level.

(5D)Error detected on an adapter.

Chips & Tech (5D)Wait state configuratio n is set-up.

AMI

Error Code – 5E

(5E)8259 interrupt controller error.

Compaq (5E)test the next adapter.

Chips & Tech (5E)1st 64K RAM re-test.

Phoenix (5E)Enter third protected mode test.

Error Code – 5F

AMI

Compaq

(5F)8259 interrupt controller test OK.

(5F)All adapters successfully tested.

Chips & Tech (5F)Shadow RAM.

Error Code – 60

ACER

AMI

(60)Set up BIOS interrupt.

(60)DMA page register test passed. About to go for DMA #1,verify from display

AST memor y.

(60)RAM size.

Award

Compaq

Chips & Tech (60)CMOS RAM.

Phoenix (60)Test expanded memory.(Beep)=2-3-1-1.(60)Base memory test.

AMI

AST

(60)Setup virus protection(Boot sector protection).

(60)Start of memor y test.

(61)RAM test.

Error Code – 61

(61)Displa y memory verification over. About to go for DMA #1 base register test.

Award

Compaq initialization. Show the system configuration table.

(61)Enter protected mode.

Chips & Tech (61)Video.

AMI

AST

Award

(61)Try to turn on level 2 cache. Set the boot up speed according to setup setting.

Last chance for chipset initialization. Last chance for power management

(62)DMA#1 base register test passe d. About to go for DMA #2 base register test.

(62)Shadow R AM.

Error Code – 62

(62)Setup daylight saving according to setup values. Program the NUM lock, type rate & type speed according to setup setting. Setup NUM_LOCK; Setup

NUM_LOCK status according to setup.

Compaq

Phoenix

AMI

AST

Award

(62)Start memory sizing.

(62)Test extended memory address lines.(Beep)=2 -3-1-3. Base memory address test.

Error Code – 63

(63)DMA #2 base register test passed . About to go for BIOS ROM data area check.

(63)Cache memory.

(63)If there is any changes in the hardware configuration, update the ESCD information(PnP BIOS only. Clear memor y that have been used. Boot s ystem via

INT 19h.

Compaq (63)Get CMOS size.

Chips & Tech (63)Protected mode interrupt.

Error Code – 64

ACER (64)Start test real time clock.

AMI

AST

Compaq

(64)BIOS ROM data area check halfwa y. BIOS ROM data area check to be complete.

(64)Copy BIOS to shadow RAM.

(64)Start test of real memor y.

Chips & Tech (64)Address line A20.

Phoenix (64)Jump to User Patch 1.(Beep)=2 -3-2-1.Shadow memory test.

Appendix A

AMI

AST

Error Code – 65

(65)DMA #2 base register test passed. About to program DMA unit 1 and 2.

(65)Copy video BIOS to shadow RAM.

Compaq (65)Start test of ext ended memory.

Chips & Tech (65)Memor y address li nes.

AMI

Error Code – 66

(66)DMA unit 1 and 2 program ming over. About to initialize 8259 interrupt

AST

Compaq controller.

(66)8254 timer channel #2.

(66)Save size of real and extend ed memory.

Chips & Tech (66)Memory Test.

Compaq (66)Configure advanced cache registers.(Beep)=2 -3-2-3. Extended memory test.

AMI

AST

Compaq

Error Code – 67

(67)8259 initialization over. About To start ke yboard test.

(67)Memor y initialize.

(67)Update 128K-Option installed CMOS bit.

Chips & Tech (67)Extended memory.

Phoenix (67)Initialize Multi Pr ocessor APIC.

Error Code – 68

ACER

Compaq

(68)Test floppy disk.

(68)Prepare to return to real mode.

Chips & Tech (68)Timer interrupt.

Phoenix (68)Enable external and CPU caches.(Beep)=2 -3-3-1. Ex- tended address test.

Compaq

Error Code – 69

(69)Back in real mode -test successful.

Chips & Tech (69)Real Time clock.

Phoenix (69)Setup System Management Mode(SMM) area.

Compaq

Error Code – 6A

(6A)Back in real mode -error during test.

Chips & Tech (6A) Keyboard contr oller.

Phoenix (6A) Display external cache size.(Beep)=2 -3-3-3.Determine memory test.

Compaq (6B)Display error messages.

Error Code – 6B

Chips & Tech (6B)Test Math chip.

Phoenix (6B)Load custom defaults(optional).

Error Code – 6C

ACER

Compaq

(6C)Test hard disk drive.

(6C)End of memor y test.

Chips & Tech (6C)Test serial port(RS232).

Phoenix (6C)Display shadow message.(Beep)=2 -3-4-1.Display error messages.

Compaq

Error Code – 6D

(6D)Initialize KB OK display string.

Chips & Tech (6D)Test parallel ports.

Error Code – 6E

Compaq (6E)Determine size to test.

Chips & Tech (6E)Dual card.

Phoenix (6E)Display possible hig h address for UMB recovery. Display non-disposable segments.(Beep)=2-3-4-3.Configure ROM/RAM BIOS.

Error Code – 6F

Compaq (6F)Start of MEMO RY TEST.

Chips & Tech (6F)Test flopp y drive controller.

ACER

AMI

(70)About to test parallel port.

(70)start of ke yboard test.

Compaq (70)Display XXXXX KB OK.

Chips & Tech (70)Test hard drive controller.

Error Code – 70

Phoenix

AMI

Compaq

(70)Display error messages.(Beep)=2 -4-1-1.System time test.

(71)Keyboard controll er BAT test over.

(71)Test each RAM segment.

Chips & Tech (71)Key-lock.

Error Code – 71

AMI

Error Code – 72

(72)Keyboard interface test over, mouse interface test started.

Compaq (72)High order address test.

Chips & Tech (72)Pointing divide.

Phoenix (72)Check for configuration errors.(Beep)=2 -4-1-3.(72) Real time clock test.

Error Code – 73

AMI

Compaq

(73)Global data initializatio n for keyboard/mouse over.

(73)Exit memory test.

Compaq

Phoenix

AMI

Compaq

Phoenix

AMI

Compaq

Phoenix

AMI

Compaq

Phoenix

AMI

Compaq

AMI

Compaq

Phoenix

AMI

Compaq

ACER

Compaq

Phoenix

AMI

ACER

AMI

Compaq

Phoenix

AMI

Compaq

AMI

Compaq

Phoenix

AMI

Compaq

ACER

Compaq

Phoenix

Compaq

AMI

Compaq

Phoenix

AMI

Compaq

ACER

AMI

Appendix A

Error Code – 74

(74)About to test serial port.

(74)Display ’SETUP’ prompt and about to start flopp y setup.

(74)Parity error on bus after memory test, s ystem halted.

(74)Test real-time clock.(Beep)=2 -4-2-1.Test for stuck keys.

Error Code – 75

(75)Floppy setup o ver.

(75)Start of protected mode test.

Error Code – 76

(76)Hard disk setup about to start.

(76)Prepare to enter protected mode.

(76)Check for keyboard errors. (Beep)=2 -4-2-3.Initialize hardware interrupt vectors.

Error Code – 77

(77)Hard disk setup over.

(77)Test software exceptions.

Error Code – 78

(78)Set real time.

(78)Prepare to return to real mode.

(78)Detect and test CoPr ocessor.

Error Code – 79

(79)About to initialize timer data area.

(79)Back in real mode -No error.

Error Code – 7A

(7A)Timer data initialized and about to verify CMOS bat tery power.

(7A)Back in real mode-error.

(7A)Determine/Init COM channels.

Error Code – 7B

(7B)CMOS batter y verification over.

(7B)Exit protected mode.

Error Code – 7C

(7C)scan option. RAMs.

(7C)High order address test failure.

(7C)Set up hardware interrupts vectors.(Beep)=2 -4-4-1.Determine LPT channels.

Error Code – 7D

(7D)About to analyze POST results. About to analyze diagnostic test results for memor y.

(7D)Enter cache controller test .

Error Code – 7E

(7E)CMOS memory size updated.

(7E)Exit cache controller test.

(7E)Test CoProcessor if p resent.(Beep)=2-4-4-3.Initialize BIOS data area.

Error Code – 7F

(7F)Look for <DEL>key and get into CMOS setup if found About to check optional ROM C000:0.

(7F)Copy System ROM to high RAM.

Error Code – 80

(80)Determine math CoProcessor is present.

(80)Keyboard test starte d, clearing output buffer, checking for stuck key, About to issue keyboard reset command. About to give control to optional ROM in segment

C800 to DE00.

(80)Start of 8042 test.

(80)Disable onboard Super I/O ports and IRQs.(Beep)=3 -1- 1-1.Detect floppy controller.

Error Code – 81

(81)Keyboard reset error/stuck key found. About to issue keyboard controller interface test command. Optional ROM control over.

(81)Do 8042 self-test.

(81)late POST device initialization.

Error Code – 82

(82)Keyboard controller interface test over. About to write co mmand byte and Init circular buffer. Check for printer ports and put the addresses in global data area.

(82)Check result received.

(82)Detect and install external RS232 ports.(Beep)=3 -1- 1-3.Test floppy drives.

Error Code – 83

(83)Command byte written, global data Init done. About to check for lock -key.

Check for RS232 ports and put the addresses in global data area.

(83)Error result.

(83)Configure non-MCD IDE controllers.

Error Code – 84

Appendix A

ACER

AMI

(84)Keyboard initialize.

(84)Lock-key checking over. About to check for memory size mismatch with

CMOS. CoProcessor detection over. 80287 check/test OK.

Compaq

Phoenix

AMI

Phoenix

AMI

Compaq

Phoenix

AMI

(84)OK 8042,Init mode=5D.

(84)Detect and install external parallels ports.(Beep)=3 -1- 2-1.Fixed disk test.

Error Code – 85

(85)Memor y size check done. About to display soft error and check for password or bypass setup. About to display soft error message. If no video replace Video card.

(85)Initialize PC-compatible P nP ISA devices.

Error Code – 86

(86)Password checked. About to do programming before setup. About to give control to system ROM at segment E000.

(86)Start keyboard test, reset keyboard.

(86)Re-initialize onboard I/O ports.(Beep)=3 -1-2-3.(86)Per form external ROM scan.

Error Code – 87

(87)Programming before setup complete. Going to uncompress SETUP code and execute CMOS setup. S ystem ROM E000:0 check over.

(87)Got acknowledge, read result.

(87)Configure Motherboard Configuration Dev ices(optional)

Error Code – 88

Compaq

Phoenix

ACER

AMI

Compaq

Phoenix

AMI

Compaq

Phoenix

(88)System #1 initialize.

(88)Returned from CMOS setup program and screen is cleared. About to do programming after setup.

(88)Got result, check it

(88)Initialize BIOS Data Area.(Beep)=3 -1-3-1.Test key- lock/keyboard t ype.

Error Code – 89

(89)Programming after setup complete. Going to displa y power on screen message.

(89)Test for stuck keys.

(89)Enable Non-Maskable Interrupts (NMIs)

Error Code – 8A

AMI

Compaq

Phoenix

AMI

ACER

AMI

Phoenix

AMI

Compaq

Phoenix

Compaq

(8A)First screen message displayed. About to displa y <WAIT…>message.

(8A)Key seems to be stuck.

(8A)Initialize Extended BIOS D ata Area.(Beep)=3-1-3-3. wait for F1 test.

Error Code – 8B

(8B)First scree n message displa yed <WAIT…>message displa yed. About to do

Main and Video BIOS sha dow.

(8B)Test keyboard interface.

(8B)Test and initialize PS/2 mouse.

Error Code – 8C

(8C)System #2 initialize.

(8C)Main and video BIOS shadow successful. Setup options programming after

CMOS setup about to start.

(8C)Got result, check it.

(8C)Initialize flopp y controller.(Beep)=3-1-4-1.Final system initialization.

Error Code – 8D

(8D)Setup options are programmed, mouse check and Init to be done next. Going for hard disk, flopp y reset.

(8D)End of test, no errors. Compaq

AMI

Error Code – 8E

(8E)Mouse check and initialization complete. Going for hard disk controller reset.

Phoenix

AMI

Phoenix

ACER

AMI

About to go For floppy check.

(8E)Interrupt 19 boot lo ader.

Error Code – 8F

(8F)Hard disk controller reset done. Floppy setup to be done nest.

(8F)Determine number of ATA drives(optional)

Error Code – 90

(90)Invoke interr upt 19 to boot loader.

(90)Floppy setup is over. Test for hard disk presen ce to be done.

Compaq (90)Start of CMOS test .

Chips & Tech (90)Set-up RAM.

Phoenix (90)Initialize hard-disk controller.(Beep)=3-2-1-1

Error Code – 91

AMI

Compaq

AMI

(91)Floppy setup complete. Hard disk setup to be done next.

(91)CMOS seems to be OK.

Chips & Tech (91)CPU speed.

Phoenix (91)Initialize local-bus hard-disk controller.(Beep)=3 -2-1-2

Error Code – 92

(92)Hard disk set up complete. About to go for BIOS ROM data area c heck.

Appendix A

Compaq (92)Error on CMOS read/write test.

Chips & Tech (92)Configuration check.

Phoenix (92)Jump to User Patch 2.(Beep)= 3 -2-1-3

AMI

Compaq

Phoenix

ACER

Error Code – 93

(93)BIOS ROM data area check halfwa y. BIOS ROM data area check to be completed.

(93)Start of DMA controller test.

(93)Build MPTABLE for multi processor boards.

Error Code – 94

(94)#5 shutdown.

AMI (94)Hard disk setup complete. Going to set base and extended memory size. BIOS

ROM data area check over.

Compaq (94)Page registers seem OK.

Chips & Tech (94)POD Bootstrap.

Phoenix

AMI

Compaq

(94)Disable A20 address line.(Beep)=3 -2-2-1

(95)DMA controller OK.

Error Code – 95

(95)Memory size adjusted due to mouse support, har d disk type-47.Going to verify from displa y memory.

Chips & Tech (95)Reset ICS.

Phoenix (95)Install CD ROM for boot.

AMI

Error Code – 96

(96)Memory size adjusted due to mouse support, hard disk type -47.Going to do any

Init before C800 optical ROM control. Returned after verifying from display memor y.

Compaq (96)8237 D MA Initialization complete.

Chips & Tech (96)BIOS PEAK.

Phoenix

AMI

(96)Clear huge ES segment register.(Beep)=3 -2-2-3.

(97)Any Init before C800 optional ROM control is over. Optional ROM check & control will be done next.

Error Code – 97

Chips & Tech (97)VGA power.

Phoenix (97)Fix-up Multi Processor table.

ACER

AMI

(98)#A shutdown.

Error Code – 98

(98)Optional ROM control is done. About to give control to do any required processing after optional ROM returns control.

Chips & Tech (98)Adapters POS.

Phoenix (98)Search for option ROMs. One long, two short beeps on checksu m failure.(Beep)=3-2-3-1.

AMI

Phoenix

AMI

Phoenix

AMI

Error Code – 99

(99)Any initialization required after optional ROM test over. Going to setup timer data area and printer base address.

(99)Check for SMART Drive(optional).

Error Code – 9A

(9A)Return after setting timer and printer base address. Going to set the RS -232 base address.

(9A)Shadow option ROMS.(Beep)=3 -2-3-3.

Error Code – 9B

(9B)Returned after RS -232 base address. Going to de any initialization before

Co-Processor test.

ACER

AMI

Phoenix

AMI

Error Code – 9C

(9C)#B shutdown.

(9C)Required initialization before co -Processor is over. Going to initialize the

CoProcessor next.

(9C)Set up Power Management.(Beep)=3 -2-4-1.

Error Code – 9D

(9D)CoProcessor initialized. Going to do any in itialization after CoProcessor test.

Error Code – 9E

(9E)Initialization after CoProcessor test is complete. Going to check expander keyboard, keyboard ID and number -lock.

Phoenix

AMI

Phoenix

AMI

Compaq

(9E)Enable hardware interrupts.(Beep)=3 -2-4-3.

Error Code – 9F

(9F)Extended keyboard check is done, ID flag set. num -lock on/off. Keyboard ID command to be issued.

(9F)Determine number at ATA and SCSI drives.

Error Code – A0

(A0)Keyboard ID command issued. Keyboard ID flag to be reset.

(A0)Start of diskette tests.

AMI

Compaq

Phoenix

AMI

Compaq

AMI

Compaq

Phoenix

Compaq

AMI

Award

Compaq

Phoenix

AMI

Award

Compaq

Phoenix

Compaq

Phoenix

Compaq

Phoenix

Compaq

Phoenix

Compaq

Phoenix

Compaq

Phoenix

AMI

Compaq

AMI

Compaq

Phoenix

AMI

Compaq

AMI

Compaq

Phoenix

AMI

Compaq

AMI

Compaq

AMI

Appendix A

(A0)Set time of day .(Beep)=3 -3-1-1

Error Code – A1

(A1)Keyboard ID flag reset . Cache memory test to follow.

(A1)FDC reset active (3F8H bit 2)

Error Code – A2

(A2)Cache memory test over. Going to display any soft errors.

(A2)FDC reset inactive(3F8H bit 2)

(A2)Check key lock.(Beep)=3 -3-1-3

Error Code – A3

(A3)Soft error display complete. Going to set the keyboard type matric rate.

(A3)FDC motoron.

Error Code – A4

(A4)Keyboard type matric rate set. Going to program memory wait states.

(A4)FDC time-out error.

(A4)Initialize Type matric rate.

Error Code – A5

(A5)Memory wait states programming over. Going to clear the screen and enable parity/NMI.

(A5)FDC failed reset.

Error Code – A6

(A6)Screen cleared. Going to enable parit y and NMI.

(A6)FDC passed reset.

Error Code – A7

(A7)NMI and parity enabled. Going to do any Initialization required before giving control to optional ROM at E000.

Error Code – A8

(A8)Initialization before E0 00 ROM control over. E000 ROM to get control ne xt.

(A8)Start of determine drive type.

(A8)Erase F2 prompt.(Beep)3 -3-3-1

Error Code – A9

(A9)Returned from E000 ROM co ntrol. Going to do any init required after E000 optional ROM control.

(A9)Seek operation initiated.

Error Code – AA

(AA)Initialization after E000 optional ROM control is over. Going to display the system configuration.

(AA)Waiting for FDC status.

(AA)Scan for F2 key stroke.(Beep)=3 -3-3-3

Error Code – AB-AF

(AC)Enter SETUP.(Beep)=3-3-4-1

(AE)Clear in-POST flag.(Beep)=3 -3-4-3.Clear Boot fag.

(AF)diskette tests complete.

Error Code – B0

(B0)System configuration is displa yed. Going to un-compress SETUP code for hot-key setup.

(B0)Spurious interrupt occ urred in protect mode. Check mismatch memory.

(B0)Start of fixed drive tests.

(B0)Check for errors.(Beep)=3 -4-1-1.Unknown interrupt occurred.

Error Code – B1

(B1)un-compressing of SETUP code is complete. Going to copy any code to specific area.

(B1)If unmasked NMI occurs, Press F1 to disable NMI,F2 to boot.

(B1)Combo board not found, exit.

Error Code – B2-B5

(B2)Combo controller failed, exit.

(B2)POST done-prepare to boot operating s ystem.(Beep)=3- 4-1-3

(B3)Testing drive 1.

(B4)Testing drive 2.

(B4)One short beep before boot.(Beep)=3 -4-3-1

(B5)Drive error(error condition).

(B5)terminate Quiet -Boot(optional)

Error Code – B6

(B6)Drive failed(failed to respond).

(B6)Check password(optional).(Beep)=3 -4-2-3

Error Code – B7-BD

(B7)CMOS RAM invalid or no fixed drives, exit .

(B8)Fixed drive tests complete.

(B8)Clear global descriptor table.(Beep)=3 -4-3-4

(B9)Attempt to boot diskette.

Appendix A

Phoenix

Compaq

Phoenix

(B9)Prepare boot.

(BA)Attempt to boot fixed drive.

(BA)Initialize DMI parameters.

Compaq

Phoenix

Compaq

Phoenix

Compaq

Phoenix

Award

(BB)Boot attempt failed(diskette or fixed).

(BB)Initiali ze PnP option ROMs.

(BC)Boot record read, jump to boot record.

(BC)Clear parity checkers.(Beep)=3 -4-4-1

(BD)Drive error, retry booting.

(BD)Display Multi -Boot menu.

Error Code – BE

Compaq

Phoenix

Award

Phoenix

(BE)Program defaults values into chipset.(BE)Chipset default initialization;

Program chipset registers with power on BIOS defaults.

(BE)Weitck CoProcessor test.

(BE)Clear screen(optional).(Beep)=3 -4-4-3

Error Code – BF

(BF)Program the rest of the chipset

(BF)Chipset initialization; Program chipset registers with setup values.

(BF)Check virus and backup reminders.(Beep)=3 -4-4-4

Error Code – C0

Award (C0)Turn off chipset cache; OEM S pecific-cache control.

Chips & Tech (C0)System board memory failure.

Phoenix

Award

(C0)Try to boot with INT 19.(Beep)=4 -1-1-1

Error Code – C1,C2,C3,C4

(C1)Memory presence test; OEM specific -test to size onboard memory. Bad

SIMM.

Chips & Tech (C1)I/O channel activated.

Phoenix (C1)Initialize POST Error Manager(PEM).

AMI

Phoenix

(C2)NMI is Disable. Power on delay start on.

(C2)Initialize error logging.

AMI

Award

(C3)Check memor y(Cache, Video or first 64 K)

(C3)DRAM Select page, Check BIOS setting and first SIMM, Possible address line

Phoenix

Award failure.

(C3)Initialize error display function.

Phoenix

AMI

Award

Phoenix

AMI

Award

Phoenix

AMI

Award

Phoenix

AMI

(C4)CMOS conflicts, check video switch, BIOS(Chipset) on the video not initializing.

(C4)initialize system error ha ndler.

Error Code – C5

(C5)Power on delay complete. Goin g to enable ROM i.c. disable Cache if an y.

(C5)Early shadow; OEM Specific -Early shadow enable for fast boot.

(C5)PnPnd dual CMOS(optional)

Error Code – C6

(C6)Calculating ROM BIOS checksum.

(C6)Cache presence test; External cache size detection. (Check Memory first

64K.Check CPU jumper Setti ng). Also, Check Video memory

(C6)Initialize notebook docking (optional).

Error Code – C7

(C7)ROM BIOS checksum passed. CMOS shutdown registe r test to be done next.

(C7)Shadow video/system BIOS after memory pass.

(C7)Initialize notebook docking late.

Error Code – C8,C9

(C8)CMOS Shutdown register test done. CMOS checksum calculation to be done

Award

Phoenix

AMI

Award

AMI

Award

AMI

Compaq next.

(C8)CMOS Shutdow n, time dela y.

(C8)Force check(optional)

(C9)Extended checksum(optional)

Error Code – CA,CB,CC

(CA)CMOS checksum calculation is done, CMOS Drag byte written. CMOS status register about to initializin g for Date and Time.

(CA)Micronics cache initialization.

(CB)CMOS status register Init done. Any initialization be fore keyboard BAT to be done next.

(CC)NMI handler shutdown.

Error Code – CD-CF

(CD)BAT command to keyboard contr oller is to be issu ed.

(CE)Keyboard controller BAT result veri fied. Any initialization after KB controller.

(CF)Initializatio n after KB controller BAT done. Keyboard command byte to be written next.

Error Code – D0-DC

(D0)Entry to clear memory routine.

Phoenix

AMI

Compaq

AMI

Compaq

Phoenix

AMI

Compaq

AMI

Compaq

Phoenix

AMI

Phoenix

AMI

Compaq

Phoenix

Compaq

Phoenix

Compaq

Phoenix

Compaq

Phoenix

Award

Phoenix

Award

Appendix A

(D0)Interrupt handler err or.(Beep)=4-2-1-1

(D1)Keyboard controller command byte is written. Going to check pressing of

<INS> key during power-on.

(D1)Ready to go to protected mode.

(D2)Checking for pressing of <INS>key during power -on done. Going to disable

DMA and Interrupt controllers.

(D2)Ready to clear extended memor y.

(D2)Unknown interrupt error.(Beep)=4 -2-1-3

(D3)DMA controller #1,#2,interr upt controller #1,#2 disable. Video display is disable and port -B is initialized. Chipset initialize/auto memory detection about to begin.

(D3)Ready to reset back to real mode.

(D4)Chipset Initialization/auto memory detection about to begin. Check SIMM for mismatch.

(D4)Back in real mode-ready to clear real mode.

(D4)Pending interrupt error.(Beep)=4 -2-2-1

(D5)RUNTIME code is un-compressed.

(D6)Initialize option ROM error.(Beep)4 -2-2-3.Shutdown error.(Beep)=4-2-3-1.(DA)Extended Block Move.(Beep)=4 -2-3-3.(DC)Shutdown

10 error(Beep)=4-2-4-1

(DD)Transfer control to un-compressed code in shadow ram at F000:F FF0.

(E0)Ready to replace E000 ROM.

(E0)Initialize the chipset.

Error Code – E1,E2

(E1)Completed E000 ROM replacement.

(E1)Initialize the bridge.

(E2)Ready to replac e EGA ROM.

(E2)Initialize the motherboard chipset, and CPU.(Beep)=4 -3 -1-3

Error Code – E3

(E3)Completed EGA ROM replacement.

(E3)Initialize refresh counter and system timer(Beep)=4 -3- 1 –4

Error Code – E4-EC

(E4)Check for forced Flash or initialize system I/O.(Beep)= 4 -3-2.(E5)Check HW status of ROM or check force recovery boot.(Beep)4 -3-2-2. (E6) BIOS ROM is OK.

(Beep) =4-3-2-3. (E7) Do a complete RAM Test or go to BIOS. (Beep)=4 -3-2-4.

(E8)Do OEM initialization or set huge segment. (Beep)=4 -3-3-1. (E9) Initialize interrupt controller or initialize multi pr ocessor. (Beep)=4-3-3-2. (EA)Read in bootstrap code or initialize OEM special code. (Beep)=4 -3 -3-3. (EB) Initialize all vectors or initialize PI C and DMA. (Beep)=4 -3-3-4. (EC) Boot the Flash program or initialize memory t ype. (Beep)=4-3-4-1. (ED) Initialize the boot device or initialize memory size. (Beep)=4 -3-4-2

Error Code – EE

(EE)Unexpected Processor exception.

(EE)Boot code was read OK or shadow boot block.(Beep)= 4 -3-4-3

Error Code – F0-F7

(F0)Initialize interrupt vectors.(F1)Initiali ze Run Time Clock. (F2) Initialize video.

(F3)Initialize System Management Mode.(F4)Output one beep before

DOS.(F5)Boot to Mini DOS.(F6)Clear Huge Segment.(F7)Boot to Full DOS.

Error Code – FF

(FF)System booting. This means that the BIOS already passed control to the operation system. If no error flags such as memory size are set ,boot via INT 19 -load system from drive A, then C; display error message if correct boot device not found.

Boot system.

Hello! I am an AI chatbot specifically trained to assist you with the Compaq Mega-Post User manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!